Search Results

Search found 2133 results on 86 pages for 'iso'.

Page 67/86 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• CloneZilla Broke My System? Ubunut Installation Lost After Running CloneZilla

  - by nicorellius

  I just read through this post and tried to get my installation back using this answer to no avail. What happened to me is this: I spent an hour or more reading through the CloneZilla docs. I thought I was ready to test it out so I burned the disc with the ISO image on it and ran it. The system I used was Ubuntu 10.04, 32-bit. Everything seemed to go fine. I made a clone of my first partition and copied it to my second partition. I followed the instructions, removed the disc and rebooted my system. At this point, I would expect to have two bootable Linux installations, identical to one another. However, upon booting, I got this error message: error: no such device: 4cf1a6ef-xxxx-xxxx-xxxx-4e3a3ce92bcd error: file not found I booted from a Live Ubuntu disc and was able to see my to partitions: 4cf1(1) and 4cf1(2) (abbreviated, because the volumes have long numbers to identify them). The 50 GB partition, on which the original Ubuntu installation sits is the number and the second partition (175 GB) is the same number with an "_" at the end. I could browse the disc partitions and see the files, but I'm not sure what to do next. I know there is a way to restore my grub loader and actually boot either of these installations, but my Linux know-how is limited. Can I edit the boot loader file to fix this problem? The only clue I have is CloneZilla said something about making a new GRUB but I thought it was going to basically modify it so I could boot either installation. Not sure what happened. I am going to look through this post for the time being to see if I can learn anything to help my problem. But I thought that, since this happened as a result of using CloneZilla, it may be a unique question for this board.

  Read the article

• Squid3 not caching simple request and response

  - by Nick Spacek

  Hi folks, I've pared down my squid.conf to try to figure this out: http_port 80 accel defaultsite=host.to.cache cache_peer ip.to.cache parent 80 0 no-query originserver acl our_sites dstdomain host.to.cache http_access allow our_sites refresh_pattern . 1 20% 4320 Requests are being proxied correctly, so that's a start. Here's a request: GET http://host.to.cache/path?some_param=true Accept: */* Accept-Charset: ISO-8859-1,utf-8 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-US,en Connection: keep-alive Host: host.to.cache User-Agent: myuseragent And the response: Connection: keep-alive Content-Length: 585 Content-Type: application/xml Date: Thu, 06 Jan 2011 18:33:11 GMT Via: 1.0 localhost (squid/3.0.STABLE19) X-Cache: MISS from localhost X-Cache-Lookup: MISS from localhost:80 The response has no caching-related headers, but I thought that refresh_pattern would set a default behavior for responses without caching-related headers. For my test, I wanted to cache everything for one minute at minimum. Am I missing something obvious? I did take a peek at this question: Squid isn't caching ...and ran through the page here: http://www.mnot.net/cache_docs/ briefly, but didn't see anything relevant (not to say that there isn't, I could have missed something). Thanks for any help.

  Read the article

• Why Wireshark does not recognize this HTTP response?

  - by Alois Mahdal

  I have a trivial CGI script that outputs simple text content. It's written in Perl and using CGI module and it specifies only the most basic headers: print $q->header( -type => 'text/plain', -Content_length => $length, ); print $stuff; There's no apparent issue with functionality, but I'm confused about the fact that Wireshark does not recognize the HTTP response as HTTP--it's marked as TCP. Here is request and response: GET /cgi-bin/memfile/memfile.pl?mbytes=1 HTTP/1.1 Host: 10.6.130.38 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:11.0) Gecko/20100101 Firefox/11.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: cs,en-us;q=0.7,en;q=0.3 Accept-Encoding: gzip, deflate Connection: keep-alive HTTP/1.1 200 OK Date: Thu, 05 Apr 2012 18:52:23 GMT Server: Apache/2.2.15 (Win32) mod_ssl/2.2.15 OpenSSL/0.9.8m Content-length: 1048616 Keep-Alive: timeout=5, max=100 Connection: Keep-Alive Content-Type: text/plain; charset=ISO-8859-1 XXXXXXXX... And here is the packet overview (Full packet is here on pastebin) No. Time Source srcp Destination dstp Protocol Info tcp.stream abstime 5 0.112749 10.6.130.38 80 10.6.130.53 48072 TCP [TCP segment of a reassembled PDU] 0 20:52:23.228063 Frame 5: 1514 bytes on wire (12112 bits), 1514 bytes captured (12112 bits) Ethernet II, Src: Dell_97:29:ac (00:1e:4f:97:29:ac), Dst: Dell_3b:fe:70 (00:24:e8:3b:fe:70) Internet Protocol Version 4, Src: 10.6.130.38 (10.6.130.38), Dst: 10.6.130.53 (10.6.130.53) Transmission Control Protocol, Src Port: http (80), Dst Port: 48072 (48072), Seq: 1, Ack: 330, Len: 1460 Now when I see this in Wireshark: there's usual TCP handshake then the GET request shown as HTTP with preview then the next packet contains the response, but is not marked as an HTTP response--just a generic "[TCP segment of a reassembled PDU]", and is not caught by "http.response" filter. Can somebody explain why Wireshark does not recognize it? Is there something wrong with the response?

  Read the article

• Shut Out of XP - No Admin Password or CDR

  - by ashes999

  I inherited an old WinXP/Linux dual-boot machine from the stoneage. Because it has Linux, the regular boot process is replaced with the Fedora boot loader; I cannot, therefore, press F8 strategically to tell my PC to boot from CD. Even if I could, it's a moot point; the CDR doesn't seem to recognize any CDs. To make things worse, there's no option to network boot. The original user is probably long gone; I don't know the password for any of the Administrator group users. I can login using my corp account, but that's unprivileged on this machine. Since I'm not an admin, I can't do crazy things, like looking at boot.ini. Or deleting files. I only have 500MB free on my C drive. I'm pretty sure I can't boot from a USB, since I didn't see any settings for this in my BIOS. How can I get admin access for my user? Edit: Things I've tried: Boot from CD (CD not recognized) Launch CD from XP (CD not recognized) Install Daemon Tools Lite so I can install from an ISO -- don't have admin privileges XP password recovery tool -- requires admin privileges Adding an admin user -- no access to Control Panel Users since I'm not an admin Logging in as both the admin users on the system (trying some standard passwords) Using Fedora to chntpw (the Fedora version installed is ancient -- 2.7)

  Read the article

• SNMP Access on Ubuntu

  - by javano

  I am trying to use SNMP to monitor a machine locally on its self and remotely. This is the snmpd.conf (Ubuntu 8.04.1): # sec.name source comunity com2sec readonly 1.2.3.4 nicenandtight com2sec readonly 5.6.7.8 reallysafe group MyROGroup v1 readonly group MyROGroup v2c readonly group MyROGroup usm readonly view all included .1 view system included .iso.org.dod.internet.mgmt.mib-2.system access MyROGroup "" any noauth exact all none none syslocation my house syscontact me <[email protected]> exec .1.3.6.1.4.1.2021.7890.1 distro /usr/bin/distro smuxpeer .1.3.6.1.4.1.674.10892.1 includeAllDisks 95% 1.2.3.4 is the local machines IP and everything is working locally. 5.6.7.8 is the remote machine and initially I am just trying to touch SNMPD with snmpwalk from the remote machine; snmpwalk -v 2c -c reallysafe 1.2.3.4 Timeout: No Response from 1.2.3.4 I have added to iptables as the very first rule; -A INPUT -p udp -m udp --dport 161 -j ACCEPT With such a loose iptables rule I can't see why I can't even touch the SNMPD on that Uubuntu Machine. There are more specific rules further down the table but as I couldn't connect I added the above. TCPDump shows the UDP packets coming in. What could be going wrong here?

  Read the article

• Want to use something like Citrix XenDesktop, Free Alternative?

  - by Chris

  I'm looking to go into IT, general office server management, and it looks like XenDesktop would be a awesome tool to use. If I get it right, you would store a central image of the OS you want to deploy (in an iso file) on the main server. Then use XenDesktop to pull that image down to the client, and it will then boot the OS inside of the virtual machine. Does it download the image of the OS and store it locally (like cloning the VM onto the client?) I'd love to find a free (possibly open source?) alternative to this, I keep on hearing about KVM in Linux and PXE booting a minimalistic OS to use remote KVMs.... Would that be what I'm looking for? Ideally, I'd like a system.. - That allows me to manage one central image for multiple clients (virtualized hardware) - Easily boot a thin client OS that connected to XenDesktop. Would those things be possible with some kind of free alternative? Some guidance would be greatly appreciated.

  Read the article

• Apache reverse proxy with VirtualHost not serving a page

  - by Mr Aleph

  I have an Apache reverse proxy set to move requests to a Tomcat Applet. The config is similar to: <VirtualHost 100.100.100.100:80> ProxyPass /AppName/App http://1.1.1.1/AppName/App ProxyPassReverse /AppName/App http://1.1.1.1/AppName/App </VirtualHost> I also have a page called summary.html that exists on 1.1.1.1 as: http://1.1.1.1/AppName/summary.html When I browse directly to it I have no problem viewing it, however if I try to get there via the reverse proxy I get a blank page. Wireshark shows me a 503, but this one is coming from the Apache reverse proxy (IP 100.100.100.100) and not the Tomcat (IP 1.1.1.1). Should I add http://1.1.1.1/AppName/ to the config? How? I tried it but I get a blank page, however this one shows on the URL bar of the browser the internal IP of the Tomcat, so, no go. Help is appreciated. Thanks. EDIT: This is the dump from Wireshark: GET /AppName/ HTTP/1.1 Host: 100.100.100.100 User-Agent: Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_8) AppleWebKit/534.52.7 (KHTML, like Gecko) Version/5.1.2 Safari/534.52.7 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Cache-Control: max-age=0 Accept-Language: en-us Accept-Encoding: gzip, deflate Connection: keep-alive HTTP/1.1 404 Not Found Date: Tue, 30 Jan 2012 09:08:51 GMT Server: Apache Content-Length: 1 Connection: close Content-Type: text/html; charset=iso-8859-1

  Read the article

• ssd firmware, linux: updating large batch of drives

  - by wryfi

  I was recently hit with a fatal firmware bug that affected dozens of Crucial SSDs deployed in my datacenter. Many of the affected machines use LSI or other proprietary SAS controllers, which Crucial's bootable ISO does not recognize. None of the affected machines has a Windows license. The story is roughly similar for other SSD mfrs, including Samsung and Intel. To resolve this issue, I was forced to stop each machine, remove the affected SSD, remove the SSD from its hotswap caddy, install it temporarily into my ThinkPad, flash the firmware, reverse, rinse, repeat. It took the better part of a day to get through all the affected devices. I am looking for hardware, software, and/or purchasing strategies to ease this pain, as SSD firmware bugs seem inevitable, and our SSD footprint is growing. My first thought is to get a laptop with eSATA and one of these cables (http://www.newegg.com/Product/Product.aspx?Item=N82E16812311004). That should at least make it so I don't have to remove the drives from their caddies. Surely others have run into this. Any novel solutions?

  Read the article

• Is this "cache administrator" error my server's problem?

  - by Eoin

  Hey, I have a CentOS VPS running Apache with a phpBB installation. One specific user has received errors when posting a message or logging in to the forum. The following issue has arisen in parallel to installing nginx, which serves only the static files of my site. Not sure if this is only coincidence. Furthermore, my setup uses redirects (in some cases, double-redirects) to point the user to a different virtual folder. So, the forum is seen to be at /translation/ but the actual files are found in /phpbb/. I'm at a loss as to what may be the underlying issue. My server? The person's ISP? She has tested both at home and at work, with similar issues. While trying to process the request: GET /phpbb/index.php?sid=f62c927e7eb8f1d60a92dcc6fd918112 HTTP/1.1 Host: www.irishgaelictranslator.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.2.13) Gecko/20101203 Firefox/3.6.13 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-za Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive Referer: http://www.irishgaelictranslator.com/phpbb/ucp.php?mode=login Cookie: phpbb3_cipi4_u=96645; phpbb3_cipi4_k=; phpbb3_cipi4_sid=f62c927e7eb8f1d60a92dcc6fd918112; __utma=153470688.1232378553.1294664234.1294664234.1294664234.1; __utmb=153470688.9.10.1294664234; __utmc=153470688; __utmz=153470688.1294664235.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); style_cookie=null The following error was encountered: Invalid Response The HTTP Response message received from the contacted server could not be understood or was otherwise malformed. Please contact the site operator. Your cache administrator may be able to provide you with more details about the exact nature of the problem if needed.

  Read the article

• DXVA and ATI.... what am I missing?

  - by Shiki

  ATI Radeon HD3650 ffdshow (the one comes with CCCP 2010-10 AND the latest from Free-codecs site) Catalyst 10.12 Latest DirectX, Windows 7 HP x64 If I try to play it simply, the player (mpc-hc) won't use the acceleration. If I disable checks, I get artifacts. Back then it worked perfectly with my Intel and ATI too (Lenovo ThinkPad T500, switchable graphics). This only appeared recently. What should I do? What am I missing? If possible, I don't really want to downgrade drivers (waaa ATI drivers s.ck ... sorry but.. honestly), because the older one got a buggy DP driver so my external display gets a totally wrong resolution. Info about the media file: Video: Format : AVC Format/Info : Advanced Video Codec Format profile : [email protected] Codec ID : V_MPEG4/ISO/AVC Writing library : x264 core 88 r1462 7fcffde Encoding settings : cabac=1 / ref=8 / deblock=1:0:0 / analyse=0x3:0x133 / me=umh / subme=8 / psy=1 / psy_rd=0.80:0.20 / mixed_ref=1 / me_range=24 / chroma_me=1 / trellis=2 / 8x8dct=1 / cqm=0 / deadzone=21,11 / fast_pskip=1 / chroma_qp_offset=-3 / threads=3 / sliced_threads=0 / nr=0 / decimate=1 / mbaff=0 / constrained_intra=0 / bframes=8 / b_pyramid=2 / b_adapt=2 / b_bias=0 / direct=3 / wpredb=1 / wpredp=2 / keyint=250 / keyint_min=25 / scenecut=40 / intra_refresh=0 / rc_lookahead=40 / rc=crf / mbtree=1 / crf=16.0 / qcomp=0.60 / qpmin=10 / qpmax=51 / qpstep=4 / ip_ratio=1.40 / aq=1:1.00 The sample file I'm testing at the moment: [Coalgirls]_Kiddy_Girl-and_01_(1920x1080_Blu-Ray_FLAC)_[91428679].mkv (I tried many x264 files, no use.) Artifacts

  Read the article

• Why might my Fedora 15 live USB persistent storage not work?

  - by Richard J Foster

  I created a Fedora 15 "live" USB stick using the live USB creator found at https://fedorahosted.org/liveusb-creator/ and the Fedora 15 i686 Desktop ISO image with the persistent storage space set to 4096MB. (The USB stick I have available has an 8GB capacity, so there should be plenty of space.) Fedora appears to boot correctly, however it seems that the persistent storage is not working. To verify this, I opened a terminal prompt, then did su - followed by yum update yum. As expected, I was informed that a new version was available. (The live CD contains version 3.2.29-4, at the time of typing 3.2.29-6 is the current version). After installing, I verified that the new version was installed by typing yum --version. I then shutdown the system using shutdown now. After the system had shut down, I rebooted and returned to the terminal prompt. On typing yum --version, I was informed that the version was 3.2.29-4 (i.e. the original version). Why might the persistent storage not be working? Is there anything I can do to fix it?

  Read the article

• KVM Guest Reboot Loop

  - by javano

  I have been pulled into a situation where a KVM server (CentOS 6.2) lost power and upon reboot one of the guests hasn't started up again (XP SP3). I have SSH'ed in and someone must have changed something relating to the hyper visors prior to the power loss, but not rebooted all the guests. This particular guest wouldn't start because it was configured to use /usr/bin/qemu-system-x86_64 which isn't there now (assuming it was before?). I changed it to use /usr/libexec/qemu-kvm as this is what all the other guests on this server seem to be using, and its booting up. Using virt-manager on my local machine I can connect to the display of the XP machine and it gets as far as this screen; http://support.gateway.com/emachines/issues/2-1131285152-01.gif The problem I face now, is that which ever option I choose the machine just reboots. So it's and endless loop. I thought that perhaps a file system error maybe present due to the unclean shutdown. There is an XP SP3 ISO mounted under the guest, which I booted from in an attempt to access the recovery tools, but I don't have the Administrator password! I am out of ideas, and it's turning out to be quite the conundrum. Should I use a 3rd party live CD to test the FS for errors? How else can I trouble shoot these restarts?

  Read the article

• How to serve media across home network?

  - by TK Kocheran

  I'm looking to share my media across my home network. Router fully supports running a DLNA server, but I don't know if it'd be better to run the server from my main server computer instead of from the router, as the router would have to operate off of a network share and my server can operate directly off of the files. Here's what I need to serve, in order of importance: ISO 1:1 DVD rips (4-8GB files), MP4/H.264 encoded videos, MKV videos, MP3 files, JPEG/CR2 images. Maybe I'm completely ludicrous for wanting to push full DVD files across my network, but in reality, I would assume that only the parts of the actual file needed (ie: menu, main video payload for main title) would be served at any one time. Plus, encoding takes time and precious disk space, so why not stream it 1:1 ;) Does anyone know of the best way to accomplish this? Main goal is to serve it to Logitech Revue downstairs and secondary goal is to serve it to other computers in the house. For music, I assume I could run a DAAP server, but I don't think that the Revue supports that (and I can't exactly throw together an app that does it just yet).

  Read the article

• Cisco BVI: Claiming IP addresses

  - by cjavapro

  I would like to make sure I understand this correctly. Given a Cisco ISO router that is set up with a BVI (a variation of a bridge route).. and the following layout "ISP router" \ "Network switch" # nothing special here. | \ | \ | \ | \ "Router 1 with NAT" "Router 2 with BVI" If I understand correctly.. the outside of a BVI will only respond to IP addresses that have already been claimed on the inside of the BVI... example subnet is 123.123.123.??? and servers inside the BVI on 123.123.123.10 and 123.123.123.11, and the NAT router is holding a public IP address of 123.123.123.50. If a connection comes in to 123.123.123.10 it will be received by router 2 but if it is received on 123.123.123.50, it will be received by router 1 and not received by router 2. and if a connection comes in to 123.123.123.90 (does not exist) it will not be received by either router. Am I correct? Is it true that the BVI router will not even receive packets to IP addresses that it does not see as existing on the inside?

  Read the article

• How do I install a different OS on a Compaq Presario cq56 with preinstalled SuSE 11?

  - by McCoy

  Thing is, I don't have a clue of Linux systems, I usually use WinXP. Bought a notebook with SuSE 11 on it, because I have my XP licence and thought I could install that if I found the chipset drivers for the hardware (which I'm not completely sure I have the right versions of). Then I thought I'd give it a shot with the SuSE, looked nice enough. But I can't get my external hd to work (tried force mount) and the banshee doesn't do anything like playing video. Since that is one of the two main purposes of this notebook, I need to get that to work. Tried downloading VLC player, but that only works with SuSE 11.1 upwards. So I downloaded a SuSE 11.3 and burned the iso. But surprise, no way the notebook would boot from cd. Same with the XP cd (considered setting up a dual boot). And no, I can't get to BIOS to reset to default, either. So I can basically do nothing else than going online with this thing and that's not enough for me (gamer in withdrawal, yikes!). I need at least to get to my firefox profile on the external hd and be able to watch video. Can somebody please help me? I think at this point I'd prefer to install XP and MAYBE the SuSE 11.3 after that. I'm not a native speaker, so please speak plainly, thanks. :) Edit: if this is impossible, could someone please help me with the external hd mount and video playback? Edit: Found out how to boot from cd by now. But still no XP, because I get bluescreen after bluescreen while setup is loading files. I guess it's the missing SATA drivers...

  Read the article

• How can one use online backup with large amounts of static data?

  - by Billy ONeal

  I'd like to setup an offsite backup solution for about 500GB of data that's currently stored between my various machines. I don't care about data retention rates, as this is only a backup of, not primary storage, for my data. If the backup is stored on crappy non-redundant systems, that does not matter. The data set is almost entirely static, and mostly consists of things like installers for Visual Studio, and installer disk images for all of my games. I have found two services which meet most of this: Mozy Carbonite However, both services impose low bandwidth caps, on the order of 50kb/s, which prevent me from backing up a dataset of this size effectively (somewhere on the order of 6 weeks), despite the fact that I get multiple MB/s upload speeds everywhere else from this location. Carbonite has the additional problem that it tries to ignore pretty much every file in my backup set by default, because the files are mostly iso files and vmdk files, which aren't backed up by default. There are other services such as EC2 which don't have such bandwidth caps, but such services are typically stored in highly redundant servers, and therefore cost on the order of 10 cents/gb/month, which is insanely expensive for storage of this kind of data set. (At $50/month I could build my own NAS to hold the data which would pay for itself after ~2-3 months) (To be fair, they're offering quite a bit more service than I'm looking for at that price, such as offering public HTTP access to the data) Does anything exist meeting those requirements or am I basically hosed?

  Read the article

• Installing 64-bit Ubuntu Server 12.04 LTS, on a VM with VMWare Player, on a 64-bit Windows 7 PC

  - by WannaBeAGeek

  I'm trying to create a VM, using VMWare Player, with an ISO image of Ubuntu Server 12.04 (LTS). The machine I'm doing the installation on has an Intel(R) Core(TM) i5 CPU, and runs 64-bit Windows 7 I managed to create the VM (gave username, password, configured network etc), but I can't install Ubuntu Server. First I get this alert : Binary translation is incompatible with long mode on this platform. Disabling long mode. Without long mode support, the virtual machine will not be able to run 64-bit code. For more details see http://vmware.com/info?id=152. When I click OK, I get another alert : This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible. This host supports Intel VT-x, but Intel VT-x is disabled. Intel VT-x might be disabled if it has been disabled in the BIOS/firmware settings or the host has not been power-cycled since changing this setting. (1) Verify that the BIOS/firmware settings enable Intel VT-x and disable 'trusted execution.' (2) Power-cycle the host if either of these BIOS/firmware settings have been changed. (3) Power-cycle the host if you have not done so since installing VMware Player. (4) Update the host's BIOS/firmware to the latest version. For more detailed information, see http://vmware.com/info?id=152. Then, when I click OK, my VM exists, and I get back to the VMWare Player home screen. I don't know much about hardware and virtualisation, so there might be some necessary info I'm not giving. Please don't hesitate to let me know what is missing in my post, for finding solutions. Thanks :)

  Read the article

• Burners freezing the PC when starting lead write in

  - by steve

  hi guys ,am having trouble with new pioneer dvdr-219l dual layer burners ,have replaced old burners with these dual layer ones . they are sata attached ,have tried img burn, xbox360 cookie burner, dvd decrypter, dvd flick , the burners seem ok burning cd and normal dvds but when trying to burn an iso to dual layer they will both freeze at the lead in write , the pc freezes including alt/delete mouse etc so have to re-boot,have tried uninstalling all burning programs that i have to eliminate conflicts and re-installing 1 at a time to see if that was the problem , still no solution am starting to think that maybe i have a bad sata cable the pc and burners dont seem to talk to each other when trying to burn dual layer ,any suggestions ???? this problem is giving me the shits ,ran microsofts fix it program and it said i had no burners installed that were capable of burning , i have had a look at device manager and the burners are there and when trouble shooted it says they are working ok , have noticed in device manager that the driver for these burners is from B.H.A.corporation file version 8.0.0.5. copyright 2000-2006 and they are not digitally sighned these burners are the latest models so how com the drivers are so old ...help please . steve

  Read the article

• Why is IIS 7.5 seeing some requests as HTTP/1.0?

  - by Zhaph - Ben Duguid

  While trying to work out why Static File Compression wasn't working on one of our IIS servers, the error was coming back as "NO_COMPRESSION_10" which translates to: Server not configured to compress 1.0 requests Looking at the requests in Fiddler, I can see that I'm requesting HTTP 1.1, but everything is being sent back as HTTP 1.0: Request (from chrome, captured via Fiddler): GET /css/reset.css HTTP/1.1 Host: [-----].com Connection: keep-alive Cache-Control: max-age=0 If-Modified-Since: Tue, 16 Oct 2012 15:04:34 GMT User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.11 (KHTML, like Gecko) Chrome/23.0.1271.95 Safari/537.11 Accept: text/css,*/*;q=0.1 Referer: http://[-----].com/ Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en;q=0.8,en-US;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Response from IIS: HTTP/1.0 200 OK Cache-Control: no-cache, no-store Pragma: no-cache Content-Type: text/html; charset=utf-8 Expires: -1 Server: Microsoft-IIS/7.5 X-AspNet-Version: 4.0.30319 X-Powered-By: ASP.NET Date: Tue, 11 Dec 2012 11:57:03 GMT Connection: close Content-Length: 108837 Other servers with the same host that I'm running this site on all respond with HTTP/1.1. How can I persuade IIS to respond with HTTP/1.1 rather than HTTP/1.0? Edit to add: Digging deeper, I can see that some responses from the server are indeed being returned compressed, so I guess really I'm trying to work out why talking to this particular server from our office seems to result in it seeing 1.0 requests, while other servers at the same co-loc don't?

  Read the article

• Ubuntu 12.10 64bit host reboots when trying to install any guest system using VirtualBox

  - by gts123

  I am having a really nasty problem with VirtualBox as everytime I try to install any guest OS(using ISO file as CD for installation media), the installation starts normally but as soon as it is about to start either installing to virtual hard drive or loading(e.g. as LiveFS) it causes the host system to reboot abruptly. Config is as below: Host system: Ubuntu 12.10 64bit - Intel® Core i7-2640M CPU @ 2.80GHz × 4 Virtualbox version: 4.1.18_Ubuntu r78361 Guest OS systems tried: 32bit version of FreeBSD 9, Debian 6, Tails 0.14 VM setup Tried to have the minimal setup necessary just in case it would avoid for each system to make sure I'd avoid conflicts, but to no avail. I've tried different values and combinations of the below but the problem still persists: Shared Clipboard: Disabled Show in fullscreen/seamless: Disabled Remember runtime changes: DIsabled Base Memory: 2048 MB Chipset: PIIX3 IO APIC: Disabled EFI: Disabled Absolute Pointing device: Disabled Processor(s): 1 CPU PAE/NX: Disabled VT-x/AMD-V: Disabled Video Memory: 12 MB 3d/2d acceleration: Disabled Storage IDE COntroller: PIIX3 (same as chipset instead of PIIX4) Use host I/O cache: No Audio: disabled Network adapter: NAT USB controller: disabled No shared folder Also another sideeffect of the reboot is that it appears that it does not log any information in the error log files; not making things any easier. Please help.

  Read the article

• ubuntu preseed installation keep missing mirror files

  - by JackWu

  Install ubuntu12.04.2 with preseed file, but there is one buggy problem about preseed mirror setting. The symptom here is installing process got stuck. So I track down the log file, and find out the real problem, the installation is looking for a file that's not there. This is just one of them, another pops up if I faked this file. This all happened during preseed, so I believe preseed has something to do with this. I google ubuntu preseed mirror and find this post saying: # If you select ftp, the mirror/country string does not need to be set. #d-i mirror/protocol string ftp d-i mirror/country string manual d-i mirror/http/hostname string archive.ubuntu.com d-i mirror/http/directory string /ubuntu d-i mirror/http/proxy string # Alternatively: by default, the installer uses CC.archive.ubuntu.com where # CC is the ISO-3166-2 code for the selected country. You can preseed this # so that it does so without asking. #d-i mirror/http/mirror select CC.archive.ubuntu.com # Suite to install. #d-i mirror/suite string lucid # Suite to use for loading installer components (optional). #d-i mirror/udeb/suite string lucid # Components to use for loading installer components (optional). #d-i mirror/udeb/components multiselect main, restricted I wonder the difference between d-i mirror/http/hostname and d-i mirror/http/mirror, I mean they all specify a mirror, right? In my preseed file, this is no d-i mirror/http/mirror, and d-i mirror/http/hostname points to my own repo as you might notice in the previous image. Here is my question: Does preseed fetches file/resource from internet, if I use local repo? Why it's looking for file that's not even there? This has bothered for quite time, many thanks in advance to anyone who might give any help.

  Read the article

• Installing Ubuntu guest crashes Hyper-V host

  - by Grant

  I have a weird problem that I don't even know where to begin diagnosing. Trying to install Ubuntu to a VM locks up the host system! My setup is: Dell R715 server, dual 16 core AMD opteron processors, 96GB RAM Dell MD3600f SAN Server 2008 R2 Datacenter System Center VMM 2012 There are 5 windows virtual machines running that have had no problems. This is the first linux VM I've tried to create. I setup a VM through virtual machine manager, set the CD drive to a Ubuntu 12.04 server x64 iso, and started it up. It boots up the normal ubuntu install menu, but the second I hit enter on "Install Ubuntu Server", I get disconnected. The HOST machine stops responding to pings. So do all virtual machines on it. It locks up entirely - keyboard on the host won't work, mouse won't move, numlock light won't change. There's no blue screen - the host is sitting at the login screen completely unresponsive. I can't find any relevant logs in event viewer after rebooting. What could cause the host machine to freeze like that? It's not a one time occurrence - it happens every time at the exact same point. Thank god this server isn't in production yet!

  Read the article

• Unable to load Windows after using EasyBCD to Reset bcd [duplicate]

  - by johnny

  This question already has an answer here: How can I repair the Windows 8 EFI Bootloader? 9 answers My windows installation was working perfectly fine until i clicked "Reset BCD" in EasyBCD in Windows 8. After clicking that EasyBCD told me to add Win 8 entry via Add Entry Menu so i did. After restart, win 8 would not start. Neither would recovery F11. Attempts i made to Restore : Ran boot-repair from ubuntu live cd several time. Used Win8 system recovery disc created via virtualbox with win 8 preview iso. Automated repair from Win8 system recovery disc Ran following commands from cmd started from Win8 system recovery disc bootrec /fixmbr Result : Success message bootrec /rebuildbcd Result : after hitting (Y) "The requested system device cannot be found" System refresh started from Win8 system recovery disc gives error that device is locked. System reset started from Win8 system recovery disc gives error that required partition or device is missing or not accessible. Used automated repair from EasyRE disc. It gave success message. Used Fix boot problem from Macrium reflect winPE repair disc. Copied Recovery partition to usb. Booting from usb gave this error Your PC needs to be repaired. Error Code : 0XC000000f Press Enter to try again Press F8 for Startup Settings F8 & Enter does nothing I cannot install WIn7 or Win 8, error it gives : "windows cannot be installed on this disk. The selected disk is of the GPT partition style."

  Read the article

• Imac g5 with no OS nor CD drive

  - by sinekonata

  What I want: Ubuntu on a g5 Imac. What I have: An empty PC (Intel g5 17" Imac) with broken CD drive. Its model is A1173. This PC with Ubuntu 12.04 and an old Vista partition. a usb flash drive. Problems: No CD means the only boot Drive I could use is USB. There are no BIOS on Macs so I can't set boot settings or even see if it detects my USB drive. When I start the machine and press ALT the first and only thing I see is an old corrupted winXP partition and not a single option or additional information. So assuming blindly that the Mac hardware/firmware works normally, I don't have any Mac OS to use any of the tools that I found on different tutorials for building a bootable .img drive for macs. I can't find much software on Linux/Windows to substitute to those tools, for example among others converting an .iso file (win/linux) to .img (mac I guess). Which makes me think that the scenario where someone like me has Mac hardware but no Mac OS is extremely rare. So other than finding someone that has a Mac I have no solution. So I ask what would you do? the only thing is it should not involve any money (I know mac soft is rarely free) which also excludes getting any MacOS unless I can use a free macos.img for VM or restore the original Mac for free. Thank you

  Read the article

• Mac OS X in Virtualbox says "You need to restart your computer"

  - by humoeba

  I've been trying to figure out for the past week how to get Snow Leopard reliably running in a VM. Right now I am using VirtualBox, and it runs fine for a while, but every once in a while (happened 3 times in the last few hours) I get the "You need to restart your computer" message. Unfortunately, it hasn't even lasted long enough to finish installing the operating system yet. I first tried VMWare, which was a pain to set up. I got it running ok, operating system installed, with the guest tools. Every once in a while though, it just stops running. I click inside the VM, and there's no mouse. It doesn't respond to keyboard input either. I have to reset the VM to get a response. I'm wondering if this is the same error. This happens with both Workstation and Player. Here is the tutorial I used for VirtualBox: http://www.sysprobs.com/iboot-loader-virtualbox-install-snow-leopard Here's the tutorial I used for VMWare: http://bobhood.wordpress.com/2009/12/18/welcome-to-snow-leopard-mac-os-x-10-6-and-vmware-workstation-7/ I'm using an iso for Mac OS X 10.6.3. I have an HP Pavilion dm4 with an Intel Core i7 M640 running Windows 7; VT is turned on. Using VirtualBox 4.0.4 and VMWare Workstation 7.0.1 and VMWare Player 3.0.1 Does anyone know what might be causing this error or how I can fix it? Thanks.

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >