Search Results

Search found 18786 results on 752 pages for 'edit insanely'.

Page 670/752 | < Previous Page | 666 667 668 669 670 671 672 673 674 675 676 677  | Next Page >

• My facebook blocking ACL has stopped working

  - by Josh

  This probably very simple. This was setup before I arrived, and has been working to block facebook. I recently eliminated some static port forwarding on this 2691 (as in, I don't think anything else has changed), and now facebook is once again accessible. Why is this list not doing what it seems like it should be doing (and was doing)? Would an extended outbound ACL be more appropriate (I think that would have been my thought if I had been tasked with creating this in the first place)? Something different? I've included below what I believe are the relevant parts of the config. interface FastEthernet0/0 ip address my.pub.ip.add my.ip.add.msk ip access-group 1 in ip nat outside ip virtual-reassembly duplex auto speed auto access-list 1 deny 69.171.224.0 0.0.31.255 access-list 1 deny 74.119.76.0 0.0.3.255 access-list 1 deny 204.15.20.0 0.0.3.255 access-list 1 deny 66.220.144.0 0.0.15.255 access-list 1 deny 69.63.176.0 0.0.15.255 access-list 1 permit any ip nat inside source list 105 interface FastEthernet0/0 overload access-list 105 deny ip 192.168.0.0 0.0.0.255 192.168.8.0 0.0.0.255 access-list 105 permit ip 192.168.0.0 0.0.0.255 any access-list 105 permit ip 192.168.1.0 0.0.0.255 any EDIT ACL is once again blocking Facebook. Here is the new definition for those interested... access-list 1 deny 66.220.144.0 0.0.7.255 access-list 1 deny 66.220.152.0 0.0.7.255 access-list 1 deny 69.63.176.0 0.0.7.255 access-list 1 deny 69.63.176.0 0.0.0.255 access-list 1 deny 69.63.184.0 0.0.7.255 access-list 1 deny 69.171.224.0 0.0.15.255 access-list 1 deny 69.171.239.0 0.0.0.255 access-list 1 deny 69.171.240.0 0.0.15.255 access-list 1 deny 69.171.255.0 0.0.0.255 access-list 1 deny 74.119.76.0 0.0.3.255 access-list 1 deny 173.252.64.0 0.0.31.255 access-list 1 deny 173.252.70.0 0.0.0.255 access-list 1 deny 173.252.96.0 0.0.31.255 access-list 1 deny 204.15.20.0 0.0.3.255 access-list 1 permit any

  Read the article

• 401 - Unauthorized On Server 2008 R2 IIS 7.5

  - by mxmissile

  I have a web application deployed to Server 2008 IIS 7.5 box. From remote it gives this error: 401 - Unauthorized: Access is denied due to invalid credentials. (remote = desktops on the same LAN) Have tried several remote clients using different browsers, all the same result. (IE, FF, and Chrome) Hitting the application from the desktop of the server itself works flawlessly. However I have not tried Firebug on the server desktop. I would assume it's still issuing a 401 status code yet returning the content anyway. See Update #2. The application is using Anonymous Authentication. The application is written in .NET 4.0 Asp.Net using the MVC framework. Static content works fine, example: http://server.com/content/image.jpg Sysinternals procmon returns these 2 results for each request: FAST IO DISALLOWED and PATH NOT FOUND. I have 2 other MVC apps running fine on the same server. I have checked the security on the folders and they all match. App runs fine on a Server 2008 IIS 7.0 box. Nothing shows up in the Event log on the server related to this. Pulling my hair out here, any troubleshooting tips? UPDATE #1: This just get's more WTF as I dig. If I click on the Application in IIS Manager - Error Pages - Edit Feature Settings select Detailed Errors, the app works remotely. Not leaving this on, so problem is not solved yet, its just more confusing. UPDATE #2: Using Firebug, I see that the Status is still 401 Unauthorized, but the Response is returning the application's correct HTML. UPDATE #3 Playing around with Failed Request Tracing, here is the WARNING Request Trace that is causing the 401: ModuleName ManagedPipelineHandler Notification 128 HttpStatus 401 HttpReason Unauthorized HttpSubStatus 0 ErrorCode 0 ConfigExceptionInfo Notification EXECUTE_REQUEST_HANDLER ErrorCode The operation completed successfully. (0x0) Update #4 Regular IIS log is showing this: #Software: Microsoft Internet Information Services 7.5 #Version: 1.0 #Date: 2010-07-20 19:17:22 #Fields: date time s-ip cs-method cs-uri-stem cs-uri-query s-port cs-username c-ip cs(User-Agent) sc-status sc-substatus sc-win32-status time-taken 2010-07-20 19:17:22 10.10.1.10 GET /Purchasing/Home - 80 - 10.10.1.12 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US;+rv:1.9.2.6)+Gecko/20100625+Firefox/3.6.6 401 0 0 4414

  Read the article

• usb mouse connecting and disconnecting randomly and often

  - by Kalec

  Yes, I know this question has been asked here before but I can't add to the discussion over there and it did not help me, so here goes nothing. I've bought an acer aspire 5742G about 2 months ago or so and it's been running great, but sometimes I used to hear the windows error beep but I had no idea what was causing it since the "bug" was automatically fixed so fast I couldn't even see an error message (also it kinda always happened when I was busy also, either in a game or while doing my homework). Later on my mouse would simply not work for 3-5 seconds then work again, I thought nothing of it at the time. I also had a problem where it only worked in one usb and one only ... to move it I had to remove the battery, unplug the laptop and hold the power button for 2 minutes to reset the bios settings. Since today though it went nuts ... sometimes it disconnects / reconnects 12 times in 10 seconds and windows just keeps beeping till I unplug it, then it runs smooth for 5-6 minutes then it goes nuts again. Other times it seems like it skips (disconnects for a fraction of a second) other times just for 2-3 seconds. But this is incredibly frustrating. Sometimes the power just goes down (the laser turns off) and well that at least I would understand but this is a rare occurance. Now I know the usb ports work since I have a lot of other devices connected and I tried the mouse on a room m8's laptop so the mouse also works. My only conclusion is that it's an operating system / settings bug and / or problem (I have tried the mouse in all ports by the way). All drivers and bios are up to date (maybe except mouse but i can't seem to update that and the mouse has no name, just a serial number which helps with nothing. Still it worked till today and nothing should have changed any way). I have made sure windows can't shut it down to save power (in device management). Also I tried to delete the drivers and re-install them, rebooting and the power button trick but nothing ... most I have done is get rid of the 12 discconnects / reconnects every 10 seconds :) but that's all :( I would buy a new one but I'm afraid it might do the same thing :| ****EDIT****** Tried the mouse again at a friend but now it didn't even install it's software nor did the update work ... think I'll just buy a new one but I'd still like a suggestion at least so I'll leave this open

  Read the article

• List repositories from multiple projects in Trac using mod_python

  - by Steffen Eriksen

  Currently working on a customized webpage that shows the available projects I have in Trac (1.0.1). I am using mod_python to connect the trac interface. I found a standard page for this, but it didn't show listing of repositories. The page showed some variables to link to the different projects, but I can't find variables to the different repositories inside the projects. I have set up the webpage from reading this: http://trac.edgewall.org/wiki/TracInterfaceCustomization (under Site Appearance) Short summary; editing ../conf.d/trac.conf: PythonOption TracEnvParentDir /parent/dir/of/projects PythonOption TracEnvIndexTemplate /path/to/template And making a template file I can edit at /path/to/template: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xmlns:py="http://genshi.edgewall.org/" xmlns:xi="http://www.w3.org/2001/XInclude"> <head> <title>Available Projects</title> </head> <body> <h1>Available Projects</h1> <ul> <dl> <li py:for="project in projects" py:choose=""> <a py:when="project.href" href="$project.href" title="$project.description">$project.name</a> ## <dd> WANT TO ADD CODE HERE! </dd> <py:otherwise> <small>$project.name: <em>Error</em> <br /> ($project.description)</small> </py:otherwise> </li> </dl> </ul> </body> </html> So... The code I want to add is something like: <dd py:for="repos in project.repository" py:choose=""> <a py:when="repos.href" href="$repos.href"> $repos.name</a> </dd> I can't figure out where to add the variables, or if there already exists some variables I can use. After searching through the files it seemed like main.py had something to do with the variables (/usr/local/Trac-1.0.1/trac/web/main.py), but at first look it didn't seem easy to just add more variables. Is there a simple way to find the rest of the variables ? And how hard is it to add more variables? Will it perhaps be easier to do this an alternative way ? All I need is to link to the repositories dynamically

  Read the article

• NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

  - by Corey Kennedy

  What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help! edit: 1/19/2011 Well, this is truly bizarre. To my knowledge I've made no changes to either system - the laptop or the server. But today after starting up the server for the first time in a few days, and making sure that nxserver was running, I was able to connect with the nxclient from my laptop with no problems. I have a full desktop in a single window and I am able to interact with it normally. This is really weird, but the problem seems to be resolved.

  Read the article

• RHEL 6.x on Rackspace Cloud and Dedicated hardware experiencing Redis Timeouts

  - by zhallett

  I just recently set up a mixture of RHEL 6.1 Rackspace cloud hosts and RHEL 6.2 dedicated hosts using Rackconnect. I am experiencing intermittent Redis timeouts from within our Rails 3.2.8 app with Redis 2.4.16 running on the RHEL 6.2 dedicated hosts. There is no network latency or packet loss. Also there are no errors on any interfaces on our cloud or dedicated servers or on the managed firewall from Rackspace. When Redis timesout, there is nothing logged within redis even though it is set up to do debug logging. The only error we receive is from Airbrake saying there was a Redis timeout. Network topology: RHEL 6.1 cloud hosts <--> Alert logic IDS <--> Cisco ASA 5510 <--> RHEL 6.2 dedicated hosts (web nodes) (two way NAT) (db hosts running redis) Ping from db host to web host: 64 bytes from 10.181.230.180: icmp_seq=998 ttl=64 time=0.520 ms 64 bytes from 10.181.230.180: icmp_seq=999 ttl=64 time=0.579 ms 64 bytes from 10.181.230.180: icmp_seq=1000 ttl=64 time=0.482 ms --- web1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999007ms rtt min/avg/max/mdev = 0.359/0.535/5.684/0.200 ms Ping from web host to db host: 64 bytes from 192.168.100.26: icmp_seq=998 ttl=64 time=0.544 ms 64 bytes from 192.168.100.26: icmp_seq=999 ttl=64 time=0.452 ms 64 bytes from 192.168.100.26: icmp_seq=1000 ttl=64 time=0.529 ms --- data1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999017ms rtt min/avg/max/mdev = 0.358/0.499/6.120/0.201 ms Redis config: daemonize yes pidfile /var/run/redis/6379/redis_6379.pid port 6379 timeout 0 loglevel debug logfile /var/lib/redis/log syslog-enabled yes syslog-ident redis-6379 syslog-facility local0 databases 16 save 900 1 save 300 10 save 60 10000 rdbcompression yes dbfilename dump-6379.rdb dir /var/lib/redis maxclients 10000 maxmemory-policy volatile-lru maxmemory-samples 3 appendfilename appendonly-6379.aof appendfsync everysec no-appendfsync-on-rewrite no auto-aof-rewrite-percentage 100 auto-aof-rewrite-min-size 64mb slowlog-log-slower-than 10000 slowlog-max-len 1024 vm-enabled no vm-swap-file /tmp/redis.swap vm-max-memory 0 vm-page-size 32 vm-pages 134217728 vm-max-threads 4 hash-max-zipmap-entries 512 hash-max-zipmap-value 64 list-max-ziplist-entries 512 list-max-ziplist-value 64 set-max-intset-entries 512 zset-max-ziplist-entries 128 zset-max-ziplist-value 64 activerehashing yes Redis-cli info: redis-cli info redis_version:2.4.16 redis_git_sha1:00000000 redis_git_dirty:0 arch_bits:64 multiplexing_api:epoll gcc_version:4.4.6 process_id:4174 uptime_in_seconds:79346 uptime_in_days:0 lru_clock:1064644 used_cpu_sys:13.08 used_cpu_user:19.81 used_cpu_sys_children:1.56 used_cpu_user_children:7.69 connected_clients:167 connected_slaves:0 client_longest_output_list:0 client_biggest_input_buf:0 blocked_clients:6 used_memory:15060312 used_memory_human:14.36M used_memory_rss:22061056 used_memory_peak:15265928 used_memory_peak_human:14.56M mem_fragmentation_ratio:1.46 mem_allocator:jemalloc-3.0.0 loading:0 aof_enabled:0 changes_since_last_save:166 bgsave_in_progress:0 last_save_time:1352823542 bgrewriteaof_in_progress:0 total_connections_received:286 total_commands_processed:507254 expired_keys:0 evicted_keys:0 keyspace_hits:1509 keyspace_misses:65167 pubsub_channels:0 pubsub_patterns:0 latest_fork_usec:690 vm_enabled:0 role:master db0:keys=6,expires=0 edit 1: add redis-cli info output

  Read the article

• Hyper-V Machine drifts time all over, even with NTP

  - by MichaelGG

  Resolved The problem was Hyper-V on that machine. I removed Hyper-V, installed VMware Server, ran the same VM. Time sync issues went away (< 100ms difference after a day). My setup is like this: HYV1 - HyperV machine (non domain) - sync irrelevant AD1 - VM AD server on HYV1, sync'd to time.nist.gov. HyperV time sync off. S1 - Physical machine, sync'd to domain. S2 - Physical machine running HyperV, sync'd to domain. V1 - Linux VM machine on S2, sync'd to AD1. No HyperV integration. AD1 and S1 have fine sync -- stripchart shows less than 100ms difference. S2 drifts like crazy. Here's a bit of the stripchart against AD1: 18:33:22 d:+00.0010138s o:+05.4101899s 18:33:24 d:+00.0010138s o:+05.4319765s 18:33:26 d:+00.0000000s o:+05.4788429s 18:33:28 d:+00.0000000s o:+05.6089942s 18:33:30 d:+00.0010138s o:+05.7240269s 18:33:32 d:+00.0000000s o:+06.0421911s 18:33:34 d:+00.0081104s o:+06.5613708s 18:33:37 d:+00.0000000s o:+06.9096594s 18:33:39 d:+00.0000000s o:+06.8867838s 18:33:41 d:+00.0010127s o:+06.8936401s In 20 seconds, it drifted over a second. If I manually reset it to within 1s, within a few minutes it'll be back drifting about 2 seconds. Overnight it went from ~2s to ~5s. The Linux VM inside S2 has perfect sync with AD1. Here's the config: C:\Users\mgg>w32tm /dumpreg /subkey:Parameters Value Name Value Type Value Data ------------------------------------------------------------ ServiceDll REG_EXPAND_SZ %systemroot%\system32\w32time.dll ServiceMain REG_SZ SvchostEntry_W32Time ServiceDllUnloadOnStop REG_DWORD 1 Type REG_SZ NT5DS NtpServer REG_SZ ad01.mydomain ad02.mydomain C:\Users\mgg>w32tm /dumpreg /subkey:Config Value Name Value Type Value Data ----------------------------------------------------------- FrequencyCorrectRate REG_DWORD 4 PollAdjustFactor REG_DWORD 5 LargePhaseOffset REG_DWORD 50000000 SpikeWatchPeriod REG_DWORD 900 LocalClockDispersion REG_DWORD 9 HoldPeriod REG_DWORD 5 PhaseCorrectRate REG_DWORD 1 UpdateInterval REG_DWORD 30000 EventLogFlags REG_DWORD 2 AnnounceFlags REG_DWORD 5 TimeJumpAuditOffset REG_DWORD 28800 MinPollInterval REG_DWORD 2 MaxPollInterval REG_DWORD 8 MaxNegPhaseCorrection REG_DWORD -1 MaxPosPhaseCorrection REG_DWORD -1 MaxAllowedPhaseOffset REG_DWORD 300 I looked at the event log, and apart from warnings about sync (after it gets way out of sync), there's no other warnings. How can I go about troubleshooting this? It's the only machine that is having this problem. All the other machines (physical and virtual) are doing fine. Edit: To clarify: The VM (AD1) has integration turned off and syncs to time.nist.gov. AD1 is fine. It's the physical machine S1 that can't sync to AD1 and drifts all over. All the other physical servers are able to sync to AD1 just fine. Update So, it appears to be an issue of running the VM. The clock slips slowly with the VM off. Turned on, it immediately starts losing seconds. I swt the VM to only use half the resources, and that seems to have slightly mitigated it, for now. Thanks!

  Read the article

• Unable to use TweetDeck on Windows due to "Ooops, TweetDeck can't find your data" and "Sorry, Adobe

  - by Matt

  I'm running Adobe AIR 1.5.2 (latest) on Windows 7 (64-bit RTM) and downloaded TweetDeck 0.31.1 (latest). When I run TweetDeck I get the following errors: Ooops, TweetDeck can't find your data and Sorry, Adobe AIR has a problem running on this computer Other AIR applications install and run fine. I've uninstalled both TweetDeck and AIR and reinstalled. Following the uninstalls I've also removed all on-disk references to both TweetDeck and AIR, but no luck. UPDATE: Using Process Monitor I did a trace of Tweetdeck from the moment it launched until the first error occurred. I saw the following information in the output of the trace: 1 5:22:18.6522338 PM TweetDeck.exe 5580 CreateFile D:\ProgramData\Microsoft\Windows\Start Menu\Programs\rs\??\d:\Use\myusername\AppData\Roaming\Adobe\AIR\ELS\TweetDeckFast.F9107117265DB7542C1A806C8DB837742CE14C21.1\PrivateEncryptedDatak NAME INVALID Desired Access: Generic Write, Read Attributes, Disposition: OverwriteIf, Options: Synchronous IO Non-Alert, Non-Directory File, Attributes: N, ShareMode: Read, Write, AllocationSize: 0 In this trace output, Tweetdeck.exe is trying to create the file D:\ProgramData\Microsoft\Windows\Start Menu\Programs\rs\??\d:\Use\myusername\AppData\Roaming\Adobe\AIR\ELS\TweetDeckFast.F9107117265DB7542C1A806C8DB837742CE14C21.1\PrivateEncryptedDatak but the path specified is invalid. When looking at the path you can see that it is indeed an invalid path. First, there’s the “??” portion which doesn’t exist in the file system since the “?” is an invalid character in Windows/NTFS file systems. Additionally, looking at this path, it actually seems to be composed of two parts (is the "??" a delimiter?): Part 1: D:\ProgramData\Microsoft\Windows\Start Menu\Programs\rs\?? Part 2: d:\Use\myusername\AppData\Roaming\Adobe\AIR\ELS \TweetDeckFast.F9107117265DB7542C1A806C8DB837742CE14C21.1\PrivateEncryptedDatak (the problem here is that d:\Use... doesn’t even exist. What seems to be happening here is that Tweetdeck is looking for the user credentials (the “PrivateEncryptedDatak” file) but it’s looking in the wrong place, can’t find the file, and hence the error that Tweetdeck is giving (shown in the screenshot). I'm trying to determine how TweetDeck is getting this path. I searched the contents of all files on my hard disk hoping to find some TweetDeck or Adobe AIR configuration file containing this incorrect path, but I was unable to find anything. UPDATE: See Carl's comment regarding directory junctions and symbolic links under my accepted answer. This ended up being the problem. Edit by Gnoupi: People, the answer section is there to provide an actual ANSWER, not to say you have the same issue. It doesn't help anyone that you have the same problem. Eventually, if you think this is really worth mentioning, put it as a comment under the question. But simply, if what you want to add is not an answer to the question, then don't post it as an answer. This is not a forum, I recommend new users to read the FAQ: http://superuser.com/faq

  Read the article

• Microsoft signed drivers appears as publisher not verfied

  - by Priyanka Gupta

  Task at hand: Microsoft sign drivers on Win 7. I microsoft signed my driver package 3 times every time thinking I might have missed a step or something. However, I cannot seem to get rid of the Windows Security error message "Windows can't verify the publisher of this driver software'. This is not the first time I have signed the driver packages. I was successfully able to sign other driver packages a few months ago. However, with this driver package I keep getting Windows security dialog box. Here's the procedure I follow - Create a new cat file using INF2CAT tool. Self sign the driver using a Versign Class 3 Public Primary Certification Authority - G5.cer. Run the microsoft tests on DTM Servers and clients with the devices that use this driver. Create WLK submission package. Self sign the cab file. Submit the package for certification. The catalog file that comes back after successfully passing tests says Name of signer "Microsoft Windows Hardware Comptibility Publisher". When I check the validity of signature using SignTool, it says the signature is vaild. However, when I try to install the driver with new signed catalog file the windows complain. Any ideas? Edit 11/12/2012: Reply to Eugene's comment Thanks for the help, Eugene. Yes. I did sign two other driver packages before. One of them was modified version of WinUSB driver. I am using the same certificate I used when I signed those two driver packages a few months ago. It costs $250 per signing from Microsoft. I would think that Microsoft would complain about it during certification if the certificate is wrong. I use the following command to self sign the CAT file. I don't have to specify the ceritificate name as there's only one certificate in the directory - Signtool sign /v /a /n CompanyName /t http://timestamp.verisign.com/scripts/timestamp.dll OurCatalogFile.cat Below is the result from running Verify command on the Microsoft signed OutCatalogFile.cat C:\Program Files\Microsoft SDKs\Windows\v7.1\Bin\x64signtool verify /v "C:\User s\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Verifying: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Hash of file (sha1): BDDF39B1DD95881B462164129758A7FFD54F47D9 Signing Certificate Chain: Issued to: Microsoft Root Certificate Authority Issued by: Microsoft Root Certificate Authority Expires: Sun May 09 18:28:13 2021 SHA1 hash: CDD4EEAE6000AC7F40C3802C171E30148030C072 Issued to: Microsoft Windows Hardware Compatibility PCA Issued by: Microsoft Root Certificate Authority Expires: Thu Jun 04 16:15:46 2020 SHA1 hash: 8D42419D8B21E5CF9C3204D0060B19312B96EB78 Issued to: Microsoft Windows Hardware Compatibility Publisher Issued by: Microsoft Windows Hardware Compatibility PCA Expires: Wed Sep 18 18:20:55 2013 SHA1 hash: D94345C032D23404231DD3902F22AB1C2100341E The signature is timestamped: Tue Nov 06 11:26:48 2012 Timestamp Verified by: Issued to: Microsoft Root Authority Issued by: Microsoft Root Authority Expires: Thu Dec 31 02:00:00 2020 SHA1 hash: A43489159A520F0D93D032CCAF37E7FE20A8B419 Issued to: Microsoft Timestamping PCA Issued by: Microsoft Root Authority Expires: Sun Sep 15 02:00:00 2019 SHA1 hash: 3EA99A60058275E0ED83B892A909449F8C33B245 Issued to: Microsoft Time-Stamp Service Issued by: Microsoft Timestamping PCA Expires: Tue Apr 09 16:53:56 2013 SHA1 hash: 1895C2C907E0D7E5C0292B92C6EA8D0E236F525E Successfully verified: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Number of files successfully Verified: 1 Number of warnings: 0 Number of errors: 0 Thank you!

  Read the article

• How to make Shared Keys .ssh/authorized_keys and sudo work together?

  - by farinspace

  I've setup the .ssh/authorized_keys and am able to login with the new "user" using the pub/private key ... I have also added "user" to the sudoers list ... the problem I have now is when I try to execute a sudo command, something simple like: $ sudo cd /root it will prompt me for my password, which I enter, but it doesn't work (I am using the private key password I set) Also, ive disabled the users password using $ passwd -l user What am I missing? Somewhere my initial remarks are being misunderstood ... I am trying to harden my system ... the ultimate goal is to use pub/private keys to do logins versus simple password authentication. I've figured out how to set all that up via the authorized_keys file. Additionally I will ultimately prevent server logins through the root account. But before I do that I need sudo to work for a second user (the user which I will be login into the system with all the time). For this second user I want to prevent regular password logins and force only pub/private key logins, if I don't lock the user via" passwd -l user ... then if i dont use a key, i can still get into the server with a regular password. But more importantly I need to get sudo to work with a pub/private key setup with a user whos had his/her password disabled. Edit: Ok I think I've got it (the solution): 1) I've adjusted /etc/ssh/sshd_config and set PasswordAuthentication no This will prevent ssh password logins (be sure to have a working public/private key setup prior to doing this 2) I've adjusted the sudoers list visudo and added root ALL=(ALL) ALL dimas ALL=(ALL) NOPASSWD: ALL 3) root is the only user account that will have a password, I am testing with two user accounts "dimas" and "sherry" which do not have a password set (passwords are blank, passwd -d user) The above essentially prevents everyone from logging into the system with passwords (a public/private key must be setup). Additionally users in the sudoers list have admin abilities. They can also su to different accounts. So basically "dimas" can sudo su sherry, however "dimas can NOT do su sherry. Similarly any user NOT in the sudoers list can NOT do su user or sudo su user. NOTE The above works but is considered poor security. Any script that is able to access code as the "dimas" or "sherry" users will be able to execute sudo to gain root access. A bug in ssh that allows remote users to log in despite the settings, a remote code execution in something like firefox, or any other flaw that allows unwanted code to run as the user will now be able to run as root. Sudo should always require a password or you may as well log in as root instead of some other user.

  Read the article

• PHP app breaks on Nginx, but works on Apache

  - by rizon1990

  I want to migrate a PHP application from Apache to Nginx. The problem is that the App breaks, because the routing doesn't work anymore and I'm not exactly sure how to fix it. The PHP application includes some .htaccess files and I tried to convert those to Nginx. The first one is in the document root: <IfModule mod_rewrite.c> RewriteEngine on RewriteRule ^$ public/ [L] RewriteRule (.*) public/$1 [L] </IfModule> The second one is in /public/ <IfModule mod_rewrite.c RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d # Rewrite all other URLs to index.php/URL RewriteRule ^(.*)$ index.php?url=$1 [PT,L] </IfModule> <IfModule !mod_rewrite.c> ErrorDocument 404 index.php </IfModule> The third and last one is: deny from all My nginx version of it looks like the following: #user nobody; worker_processes 1; #pid logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; #tcp_nopush on; keepalive_timeout 65; gzip on; server { listen 8080; server_name localhost; root /Library/WebServer/Documents/admin; location / { index index.php; rewrite ^/$ /public/ break; rewrite ^(.*)$ /public/$1 break; } location /public { if (!-e $request_filename){ rewrite ^(.*)$ /index.php?url=$1 break; } } location /library { deny all; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } location ~ \.php$ { root /Library/WebServer/Documents/admin; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } } } The problem I face is that something that the routing is broken and just returns a 404 page instead. Hopefully someone has an idea and know how to fix it ;) Thanks EDIT I got it working with this config location /library { deny all; } location ~* ^.+.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js)$ { access_log off; rewrite ^(.*)$ /public/$1 break; } location / { rewrite ^/(.+)$ /index.php?url=$1 last; } I'm sure there are better solutions and I'm open for suggestions.

  Read the article

• Mysteriously empty $_POST array

  - by Lex

  Hi all! I have the following HTML/PHP page: <?php if(empty($_SERVER['CONTENT_TYPE'])) { $type = "application/x-www-form-urlencoded"; $_SERVER['CONTENT_TYPE'] = $type; } echo "<pre>"; var_dump($_POST); var_dump(file_get_contents("php://input")); echo "</pre>"; ?> <form method="post" action="test.php"> <input type="text" name="test[1]" /> <input type="text" name="test[2]" /> <input type="text" name="test[3]" /> <input type="submit" name="action" value="Go" /> </form> As you can see, the form will submit and the expected output is a POST array with one array in it containing the filled in values and one entry "action" with the value "Go" (the button). However, no matter what values I enter in the fields; the result is always: array(2) { ["test"]=> string(0) "" ["action"]=> string(2) "Go" } string(16) "test=&action=Go&" Somehow, the array named test is emptied, the "action" variable does make it through. I've used the Live HTTP Headers extension for Firefox to check whether the POST fields get submitted, and they do. The relevant information from Live HTTP Headers (with a, b and c filled in as values in the textboxes): Content-Type: application/x-www-form-urlencoded Content-Length: 51 test%5B1%5D=a&test%5B2%5D=b&test%5B3%5D=c&action=Go Does anybody have any idea as to why this is happening? I'm freaking out on this one, it has cost me so much time already... EDIT: We've tried this on different servers, on Windows boxes it does work, on the Ubuntu server with PHP version 5.2.4 (with Suhosin), it doesn't. It even works on a different server, also with Ubuntu and the same PHP version, also with Suhosin installed.

  Read the article

• Avoid read-write access to bad sectors on HDD to continue working on the HDD

  - by goldenmean

  I have a HP Pavilion dv6446 notebook. It had Windows Vista Home premium. After 4.5+ years of usage, just recently it started malfunctioning. While working fine, its screen goes white or sometimes some thin black lines horizontally. Laptop freezes. Hard reboot works. Again it works for some 2 hrs or so, same error. To diagnose I did run the Memory and Hard disk check which is present in the Bios Setup. Memory test passed. Hard disk test returned an error saying something like - "Replace the hard disk". Bad.. Some sectors or platters have gone bad on the disk. (I confirmed this later by further tests mentioned below) Then I tried installing a Ubuntu 11.10. It listed 3 partitions /dev/sda1, sda2, sda2. It again gave error and could not install grub loader on /dev/sda1. Bad sectors. Then redid the Ubuntu installation, this time asked to to install the Ubuntu on /dev/sda3. and kept /dev/sda1 for /home. Installed fine, and works fine as well. Due to unavailability of WiFi/ Ethernet driver for that adapters under Ubuntu( at least I could not configure them and get the networking working at all), I decided to go back to reinstall windows Vista. It did install fine. I did not have to format one data partition which has my data. I just formatted one partition which installed Windows So in effect HDD has not undergone a full format here. Worked ok for 1 day. But same white screen and freeze happened. Looks like while it is in use, it accesses the bad sectors for storing some data and that's when it bombs. I am inclined to think HDD has not failed fully or crashed but has developed bad sectors. Else if it was a HDD crash, it would have refused to boot at all let alone install on it. Questions: Is there any HDD test check under windows or any such tools windows/linux based ewhere which can identify the bad sectors of the HDD and 'lock/isolate' them from further read-write access of any kind. If not what are my options, if any to salvage this laptop HDD without replacing it. EDIT: Would the Disk Error checking tool under windows help in any way?

  Read the article

• Permission denied install Joomla CiviCRM

  - by Tim

  Dear All, I am trying to install CiviCRM on a Joomla 1.5.17 web server running Ubuntu 9.10. Uploading the package to the tmp directory in /var/www/[site name]/tmp and installing creates this error: Warning: fopen(/var/www/trbcp/administrator/components/com_civicrm/civicrm/templates/CRM/common/civicrm.settings.php.tpl) [function.fopen]: failed to open stream: Permission denied in /var/www/trbcp/libraries/joomla/filesystem/file.php on line 240 Warning: fopen(/var/www/trbcp/administrator/components/com_civicrm/civicrm/templates/CRM/common/civicrm.settings.php.tpl) [function.fopen]: failed to open stream: Permission denied in /var/www/trbcp/libraries/joomla/filesystem/file.php on line 240 Warning: include_once(/var/www/trbcp/administrator/components/com_civicrm/civicrm.settings.php) [function.include-once]: failed to open stream: Permission denied in /var/www/trbcp/administrator/components/com_civicrm/configure.php on line 115 Warning: include_once() [function.include]: Failed opening '/var/www/trbcp/administrator/components/com_civicrm/civicrm.settings.php' for inclusion (include_path='.') in /var/www/trbcp/administrator/components/com_civicrm/configure.php on line 115 Warning: require_once(DB.php) [function.require-once]: failed to open stream: No such file or directory in /var/www/trbcp/administrator/components/com_civicrm/configure.php on line 140 Fatal error: require_once() [function.require]: Failed opening required 'DB.php' (include_path='.') in /var/www/trbcp/administrator/components/com_civicrm/configure.php on line 140 Initially I got a permissions denied error and thought that Joomla did not have permissions to all its directories but looking at Help-System information all the necessary directories are writable. I then decided to chmod 777 all the directories and try again but it still fails. Looking at the directories afterwards it seems that the new directories being created are not being created 777. By changing them I can get at least one step further before the error appears again. My question is does anyone know how to get round this? I am thinking that the new directories being created will require sudo privileges to have mv and create actions carried out, hence the permission denied errors. Can this be configured in Joomla? Or is there a way to specify that new directories created in /var/www/[site name] take 777 by default? any help greatly appreciated! EDIT: P.S. if anyone could give me a clue as to how the insert code feature works as well that would be great! Might make this post a bit more readable! EDIT2: Well I have had a bash at changing the permissions and ownership. sudo chown -R www-data:www-data /var/www/trbcp I then tried changing the whole /var directory (insecure I know but this is a test and dev server for me to find my feet on) to 777 and still getting permission errors. It seems to be error opening stream? Not a php guy so not sure what that is but could it be that permissions to run php script need to change? any thoughts greatly appreciated.

  Read the article

• Buying a new printer instead of replacing ink?

  - by Kelsey

  With prices of basic printers being around $40 - $50 and a ink cartridge being around $20 - $30 each for black AND color. It costs me more to replace the printer's ink than to just buy a brand new printer. This just seems like a total waste of materials though (I have 4 printers sitting in my basement with no ink). I know the ink cartridges are smaller (not as full) in a new printer but I go through it in about 1 to 1.5 years only and by then my $40 gets me a better printer to boot. Also with certain printers the heads are not part of the ink (Epson use to do this and still might) so I get new heads as well. Is this a bad practice? Are retailers making this a reality when they are selling working hardware cheaper than replacement parts? Is there something more I should be considering? Edit: Some background, long ago I bought an Epson printer which I used to print docs etc vary rarely. The ink started running low so I bought to new carts for around $60 if I recall. The printer then stopped working so I replaced the carts with the new ones but the head was dead on the black which was not worth repairing. I bought a new HP printer for $49. This lasted around 1.5yrs and then the ink ran out, I went to buy new carts and the guy at the store got me to buy a new printer (that was smaller, faster, higher dpi, etc) and it was cheaper than replacing the ink. When the ink ran out on that one I bought a new printer again, etc. The printer gets used maybe once a week at most and I never print photos or anything. It normally is jsut stored away unplugged accumulating dust. People say to buy a laser printer but they are much larger, do not print color, (in the price range I am looking at) and might have the exact same issues. The problem I see is the manufacturer is making my behaviour possible by selling new printers at a loss hoping that they will cash in on the ink later. How can they produce a printer for so cheap which HAS ink in it, and the refills cost more than the unit? It can't.

  Read the article

• CPU overheating after cleaning it

  - by Roberts

  I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

  Read the article

• Apache proxy pass in nginx

  - by summerbulb

  I have the following configuration in Apache: RewriteEngine On #APP ProxyPass /abc/ http://remote.com/abc/ ProxyPassReverse /abc/ http://remote.com/abc/ #APP2 ProxyPass /efg/ http://remote.com/efg/ ProxyPassReverse /efg/ http://remote.com/efg/ I am trying to have the same configuration in nginx. After reading some links, this is what I have : server { listen 8081; server_name localhost; proxy_redirect http://localhost:8081/ http://remote.com/; location ^~/abc/ { proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://remote.com/abc/; } location ^~/efg/ { proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://remote.com/efg/; } } I already have the following configuration: server { listen 8080; server_name localhost; location / { root html; index index.html index.htm; } location ^~/myAPP { alias path/to/app; index main.html; } location ^~/myAPP/images { alias another/path/to/images autoindex on; } } The idea here is to overcome a same-origin-policy problem. The main pages are on localhost:8080 but we need ajax calls to http://remote.com/abc. Both domains are under my control. Using the above configuration, the ajax calls either don't reach the remote server or get cut off because of the cross origin. The above solution worked in Apache and isn't working in nginx, so I am assuming it's a configuration problem. I think there is an implicit question here: should I have two server declarations or should I somehow merge them into one? EDIT: Added some more information EDIT2: I've moved all the proxy_pass configuration into the main server declaration and changed all the ajax calls to go through port 8080. I am now getting a new error: 502 Connection reset by peer. Wireshark shows packets going out to http://remote.com with a bad IP header checksum.

  Read the article

• Tomcat and IIS 7 both on different ip's and different ports

  - by n00b

  I have Tomcat and IIS 7 installed together on a Windows 2008 server. The machine has two IPs (134.133.1.1 and 134.133.2.2). I want Tomcat to handle 134.133.1.1, on port 80, and IIS to handle both 134.133.2.2, on port 80 AND 134.133.1.1, on port 443, but can't seem to get the last two together (I can get one or the other by themselves on IIS, along with the first IP address on Tomcat). I have configured Tomcat to successfully listen to ip 134.133.1.1, on port 80 with this configuration; <Connector port="80" protocol="HTTP/1.1" address="134.133.1.1" connectionTimeout="20000" redirectPort="8443" /> I also have a site configured in IIS bound to ip 134.133.1.1, on port 443 (SSL). When I turn on IIS, after Tomcat, I can reach both 134.133.1.1:80 (Tomcat) and 134.133.1.1:443 (IIS) successfully (as desired). The problem now comes when I want to introduce a new site via IIS, at the new ip address. In IIS I have setup a new site at IP 134.133.2.2, port 80. I can not start the site. The event log shows this error; Unable to bind to the underlying transport for [::]:80. The IP Listen-Only list may contain a reference to an interface which may not exist on this machine. The data field contains the error number. I think this is because IIS 7 tries to listen to port 80 on all IPs, and it cant because Tomcat is taking port 80 for 134.133.1.1. From reading, the resolution is to specify the IP address you want IIS to bind on port 80. The problem is, when I add 134.133.2.2 to the iplisten list, then I get a 404 when I try navigating to 134.133.1.1:443. I assume this is because IIS is no longer listening to ANY port on 134.133.1.1. How do I resolve this such that IIS will return both sites? EDIT: Per request my IIS binding for site A is 134.133.2.2 on port 80 (http) and 134.133.2.2 on port 443. For site B in IIS, the binding is 134.133.1.1 on port 443 (https). Note the IPs in this example are just for example purposes, but consistent with my setup.

  Read the article

• Apache works on http and https, SVN only on http

  - by user27880

  I asked a question about this before, and got most of it fixed. If I switch off https redirect and go to http://mydomain.com/svn/test0, I get the authentication window popping up, and I can enter my AD credentials, and bingo. Switching https redirect back on, if I go to http://mydomain.com I am automatically redirected to https, which is what I want, and the 'CerntOS test page' pops up. Perfect. The problem occurs when I want to go to one of my test repos via https. Here is my httpd.conf file, with confidential information suitably hosed... === NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] ServerName svn.mycompany.com ErrorLog logs/subversion-error_log CustomLog logs/subversion-access_log common Redirect permanent / https://svn.mycompany.com </VirtualHost> <VirtualHost svn.mycompany.com:443> SSLEngine On SSLCertificateFile /etc/httpd/ssl/wildcard.mycompany.com.crt SSLCertificateKeyFile /etc/httpd/ssl/wildcard.mycompany.com.key SSLCertificateChainFile /etc/httpd/ssl/intermediate.crt ServerName svn.mycompany.com ServerAdmin [email protected] ErrorLog logs/subversion-error_log CustomLog logs/subversion-access_log common <Location /svn> DAV svn SVNParentPath /usr/local/subversion SVNListParentPath off AuthName "Subversion Repositories" # NT Logon Details Require valid-user AuthBasicProvider file ldap AuthType Basic AuthzLDAPAuthoritative off AuthUserFile /etc/httpd/conf/svnpasswd AuthName "Subversion Server II" AuthLDAPURL "ldap://our-pdc:389/OU=Company Name,DC=com,DC=co,DC=uk?sAMAccountName?sub?(objectClass=*)" AuthLDAPBindDN "DOMAIN\subversion" AuthLDAPBindPassword XXXXXXX AuthzSVNAccessFile /etc/httpd/conf/svnaccessfile </Location> </VirtualHost> === Now, in ssl_error_log, I get === ==> /etc/httpd/logs/ssl_error_log <== [Fri Nov 01 16:07:55 2013] [error] [client XXX.XXX.XXX.XXX] File does not exist: /var/www/html/svn === This comes from the DocumentRoot directive further up the httpd.conf file, which of course points to /var/www/html. I know that this location is wrong, but how can I get SVN to serve the repo? I tried an Alias directive as so .. Alias /svn /usr/local/subversion .. but this didn't work. I tried to alter the Location directive. That didn't work either. Can someone help? I sense that this is so close to being solved ... Thanks. Edit: apachectl -S output: [root@svn conf]# apachectl -S VirtualHost configuration: 127.0.0.1:443 svn.mycompany.com (/etc/httpd/conf/httpd.conf:1020) wildcard NameVirtualHosts and default servers: default:443 svn.mycompany.com (/etc/httpd/conf.d/ssl.conf:74) *:80 is a NameVirtualHost default server svn.mycompany.com (/etc/httpd/conf/httpd.conf:1012) port 80 namevhost svn.mycompany.com (/etc/httpd/conf/httpd.conf:1012) Syntax OK

  Read the article

• Hyper-V causes boot loop/failure on a non-Gigabyte Win8 Pro system

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated. EDIT: I found a collection of tips here.. http://social.msdn.microsoft.com/Forums/en-US/wptools/thread/b06cc9f2-aa5e-4cb3-9df1-0c273e1dfd68 So i've been attempting various bios settings to resolve this issue with no luck. I've tried setting 'CPUID Limit' to disabled. This seems to work partly as Win8 boots but no USB devices work at all. I also attempted disabling the usb 3.0 controller as the msdn topic lists an issue with USB controllers on Gigabyte boards. This also doesn't work. The USB devices light up but no input is received by the OS. All of my other bios CPU settings are in line with the info in the post. I'm totally stumped. Bios screenshots: http://i.imgur.com/yKN5u.png http://i.imgur.com/Y9wI4.png http://i.imgur.com/F6EuO.png

  Read the article

• getUserPrincipal() in JCIFS / Lan-Manager authentitation level setting in Windows 2k8

  - by Chris

  I have to find out in which exact format JCIFS stores the user principal in the "getUserPrincipal()" property. Therefor i created a test Environment like this: Windows Server 2008 Domain Controller Domain named "MYDOMAIN" Many Testusers in Active Directory Tomcat Application Server with my Web Application (which simply reads the user Principal and displays its values). The user should be logged in to the web-application with SSO therefor i need the format that jcifs is using to store the user. (For example user@MYDOMAIN or MYDOMAIN\user...) I tested the Authentication with other SSO frameworks with Kerberos Method and it works as expected. I'm now trying to use SSO through the NTLMHttpFilter of JCIFS. When i try to login i get the following error message: jcifs.smb.SmbException: The parameter is incorrect. jcifs.smb.SmbTransport.checkStatus(SmbTransport.java:541) jcifs.smb.SmbTransport.send(SmbTransport.java:641) jcifs.smb.SmbSession.sessionSetup(SmbSession.java:322) jcifs.smb.SmbSession.send(SmbSession.java:224) jcifs.smb.SmbTree.treeConnect(SmbTree.java:176) jcifs.smb.SmbSession.logon(SmbSession.java:153) jcifs.smb.SmbSession.logon(SmbSession.java:146) jcifs.http.NtlmHttpFilter.negotiate(NtlmHttpFilter.java:189) jcifs.http.NtlmHttpFilter.doFilter(NtlmHttpFilter.java:121) Regarding to the documentation i'm using to configure this, this is a know issue with the Group policy. It is stated there, that i have to change the Group policy "Networkaccess: lan-manager authentication level" to respond to NTLMv1 request. I have done this, but it's still not working. So what i also have to configure is the same policy on the client computer. I have to change the policy, so that the client computer sends NTLMv1. But it is always sending NTLMv2 tokens. The problem now is that i'm somehow not able to change this setting. (I already was before) because the dropdown box to choose the authentication method is "greyed out". edit: just to make this clear, this dialog is on the client-side in the "local-security policies" As you can see from this screenshot, the chosen method is "Only send NTLMv2 responses" which is the wrong setting and i'm pretty sure that this is causing the error above. My question is now, why can't i change this setting? Why is it greyd out?

  Read the article

• Hibernating and booting into another OS: will my filesystems be corrupted?

  - by Ryan Thompson

  Suppose I have Windows and Linux installed on the same computer. If I hibernate Windows, can I boot into Linux without corrupting the Windows filesystem when I resume Windows? What about the other way around? What if I hibernate one, boot into the other, and mount the hibernated filesystem read/write? Read-only? If this is unsafe, is there any way to detect the hibernated state of the other OS and prevent mounting its filesystem? Basically, how far can I push this before it breaks, and how dangerous is it near the edge? I think I know the answers to some of the above questions, but for other ones, I have no idea, and for obvious reasons I have not tested this on my own computer. If someone has tested these, please enlighten the rest of us. I'm not necessarily looking for a specific answer to every question; I'll accept any response that answers a reasonable portion. EDIT: Let me clarify that when I say "hibernate," I mean the process of writing the contents of RAM to the hard disk and completely powering down the computer. In this state, powering the computer back on brings you through the BIOS and bootloader again, and you could theoretically select another operating system on a multi-boot system. Anyway, on with the original question: RESULTS Ok, after everyone's assurances that this would work, I tested it for myself. I set up Ubuntu to remount all ntfs filesystems and external drives read-only before hibernating. There was no need for a similar Windows setup because Windows does not read Linux filesystems. Then, I tried alternately hibernating one operating system and resuming the other, back and forth a few times. I even tried mounting the Windows filesystem from Ubuntu read-write, and creating a few files. Windows didn't complain when I resumed. So, in conclusion, you can more or less freely hibernate in a dual-boot Windows/Linux scenario. Note that I did not test a dual Linux/Linux co-hibernation situation. If you have two or more Linux installs and you hibernate one of them, you might be able to corrupt the filesystem by mounting it from another.

  Read the article

• Exchange 2010 forwarded emails by external servers being blocked

  - by MadBoy

  Our users were getting spam messages from their own accounts (same domain/login for example [email protected] to [email protected]). This is preety standard trick and I decided to block it so that anonymous users can't send emails as @company.com. This brought some problems on us like our printers not being able to send emails etc but I solved it with secondary smtp receiver on different port with ip restrictions. However it seems to affect forwarding by some e-mail servers as well: Hi. This is the qmail-send program at home.pl. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. : 89.14.1.26 failed after I sent the message. Remote host said: 550 5.7.1 Client does not have permissions to send as this sender --- Below this line is a copy of the message. Return-Path: Return-Path: Received: from mail.company.com [89.14.1.26] (HELO mail.company.com) by company.ho.pl [79.93.31.43] with SMTP (IdeaSmtpServer v0.70) id 488fcb01c2f069d9; Tue, 3 Jan 2012 09:46:55 +0100 Received: from EXCHANGE1.COMPANY ([fe80::d425:135f:b655:1223]) by EXCHANGE2.COMPANY ([fe80::193f:51ac:9316:cb27%14]) with mapi id 14.01.0355.002; Tue, 3 Jan 2012 09:46:55 +0100 From: =?iso-8859-2?Q?MadBoy?= So basically server forwards it without affecting email address it was send with and our servers treat it like spam. I used this command to block things: Get-ReceiveConnector "DEFAULT Exchange2" | Get-ADPermission -user "NT AUTHORITY\Anonymous Logon" | where {$_.ExtendedRights -like "ms-exch-smtp-accept-authoritative-domain-sender"} | Remove-ADPermission Is there anyway I can keep on receiveing things like forwards but be able to block things (except some dedicated antispam solution - this will be added later). Also how do I "reassing" back the permissions that was removed? EDIT to clarify: I have a domain domain.com configured as Authorative. Couple of our users are on project for differentcompany.com which is not on our servers or anywhere close. Now when they send an email from their accounts lets say [email protected] to [email protected] that special alias is configured so that any email it receives it forwards to multiple people including a group alias at our domain [email protected] and that group alias puts the email in users mailboxes. After the email is forwarded by [email protected] and it reaches our server it is denied because the forwarding done by the "external" server doesn't affect user information so for the server it seems like the [email protected] was actually sender and it treats it as spam and denies it. The server at differentcompany.com just adds itself to the header that it passed thru it and doesn't modify sender at anyway (seems like this is how forwarding works). Although I could probably allow this particular server as allowed to relay but this would seem to affect more servers/users as anyone can setup forwarding on their email back to our domain...

  Read the article

• Adobe Reader not loading form content

  - by wullxz

  We have an FDL file which is used to offer an online application possibility. The FDL is filled out and sent to a mailbox. When I open the received file, Adobe Reader starts, loads the document in Internet Explorer (had to change my default browser because it doesn't work in chrome - the customer uses IE as default) and displays a warning that Adobe Reader has blocked the connection to the server where the initial document is saved: I can then click on "Trust this document once" (translated by me!) or "Add this host to trusted hosts" (also translated by me!). The second option doesn't work at all. The first option works but is a little bit annoying. I looked into Adobe Readers options (Edit - "Voreinstellungen" in german / the last option - Security (advanced)) and found the possibility to add hosts, files and directories or allow Adobe Reader to use the "Trusted Websites" list from Internetoptions. When I add the website either to Trusted Websites or the trusted list in Adobe Readers options, the warning doesn't pop up but the content in the prefilled (by the applicant) input boxes of the document doesn't show up on Windows 7 but it does show up on Windows XP. This Screenshot shows the settings window described in the last paragraph. The big input box at the bottom normally holds the trusted files/directories/hosts list. System Information: Windows 7 Enterprise x64 Adobe Reader X multiple IE versions (mine is latest but there's also IE 7 or 8) How do I get Adobe Reader to load the content of the form? This behaviour can be reproduced on a PC. When opening an fdf from a command line the form fields are blank even though there is data in the fdf and the pdf is located in a mnaully entered trsuted folder. Steps to reproduce: Clean install a Windows 7 PC (or use a virtual box) Map a network drive to a shared folder with a subfolder e.g. c:\test\docs becomes m:\docs Set security permissions to allow full control to everyone Add an fdf and a matching pdf file in the subfolder Manually add m:\docs to each of the trusted folders in the trust manager registry settings Ensure that Enhanced Security is on Run a command line to open the fdf file Expected result: pdf is opened in Adobe Reader with form fields filled out with data Actual results: pdf is opened with blank fields 'Yellow bar' appears asking to add document to trusted locations It appears that Adobe Reader XI is ignoring the privileged locations entries in the registry. Adding the document via the 'yellow bar' adds the individual document, with the same folder, to the privileged locations but means that the process has to be repeated for every document that needs to be opened from the folder.

  Read the article

• SQL 2008 R2 Named Instance Client Connectivity Issues?

  - by Jerry Dodge

  We're upgrading our software from using SQL 2000 to 2008 R2. Our customers will be installing an update which uninstalls 2000 and installs 2008 R2 under the same instance. So if no instance existed, then no instance name will be set (default). However, the problem starts with the customers which have a named SQL instance. Starting in 2008 R2 (not sure of ones before), for some reason, a client connecting to the server by its instance name is unsuccessful. I'm testing from the Management Studio - if I can't connect this, then nothing can connect. I browse network servers, and find the specific server\instance in the list. But, upon trying to connect to an instance name like MyServer\INST, I get: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) I do in fact have TCP/IP and Named Pipes protocols enabled, this is the first thing I did. When I connect to the server using a comma (,) and port number like MyServer, 49195, it works just fine. So it appears that client computers are just unable to identify the instance names. This has happened on all our installations of SQL 2008 R2 and from all client computers, including Win 7, XP, Vista, Server 2008, and Server 2003. We never experienced such issues on earlier versions of SQL. The problem even persists if the firewalls and antiviruses are all disabled. Now, this is a large update which we will be distributing soon to all our customers, and we want to minimize the interaction they need with us to get this installed. We absolutely hate the idea of using a port number, because it will always be different, and we would have to modify each client to point to this server/port. Some of our customers may have hundreds of client computers. How do I make client connections to a named SQL instance work again? After all, this is the whole purpose of named instances, and if a client can't connect to this instance by its name, then what is it even named for? EDIT It was mentioned to make sure SQL Browser is running, so I checked, and it is running. The server is also able to connect to its self (locally) - just external connections are refused. UPDATE After more careful checking, I learned the firewall wasn't completely disabled when testing, and upon disabling it completely, this works. So it appears that SQL Browser is being blocked by the firewall from external clients from accessing.

  Read the article

< Previous Page | 666 667 668 669 670 671 672 673 674 675 676 677  | Next Page >