Search Results

Search found 18151 results on 727 pages for 'upside down'.

Page 679/727 | < Previous Page | 675 676 677 678 679 680 681 682 683 684 685 686  | Next Page >

  • Issues with Verizon's "Network Extender" device talking on my home network.

    - by Logan
    I recently switched my phone service to Verizon from ATT, and I get somewhat spotty service in my house. I called them and they sent me a "network extender" device for free. Its a femtocell that connects to my home network. The directions that come with it are very dumbed down, basically just say to connect it to your router and put it near a window (so it can get a GPS signal, it has to make sure its within the correct area before operating). The problem I'm having is the network light on it stays red. The troubleshooting information that came with it tells me this means there is a bad network connection. Its connected through an ASUS router running DD-WRT. No other devices on my network have a problem with it, including a Western Digital WDLIVE device, mine and my wife's cell phones (via wifi), a Wii, and an Xbox. If I connect the device directly to my cable modem, the light goes blue (which means good) and it starts working. So this tells me that its definately a configuration issue with my router. Verizon basically washed their hands of me when I connected it to my cable modem, and told me that its a router issue and to try a different router. Because normal people just have extra routers laying around their houses... When I connect it to the router, I can watch the DHCP Clients list on the status page, and the MAC of the network extender quickly fills up the clients list, grabbing every available DHCP address. Its like it grabs an address, can't connect to the internet, releases it, grabs another, then another, then another. So in the DHCP server settings I assigned a static IP to its MAC. This made it quit doing what it was doing before, but its still not working. I found the ports I needed to open on verizon's website, and opened them in the port forwarding config on my router. This still didn't help. So, I tried setting the network extender device's IP as the DMZ IP on the router. This still did no good. I called Verizon back and got the tech to write up a report which he passed on to a "senior network tech" who I got a call back from a few hours ago. This guy told me that while an ASUS router isn't listed as a supported device, he's not really sure why its not working. He suggested restoring the firmware to stock ASUS firmware and trying again. I have a very hard time believing its DD-WRT doing this, since every other device is working just fine with it. But its also not the Network Extender, since it works just fine when connected directly to the modem. At this point I'm out of ideas, and the next step is to restore the stock firmware on my router, and then going to walmart and getting a linksys WRT-54G to try. Is there anything else I could try before going that drastic? Cliffs- -Network extender won't work behind router, works when connected directly to cable modem. -Extender goes nuts when allowed to pick its own DHCP address, I had to assign it a static IP. -Won't work when correct ports are forwarded to it -Won't work with a DMZ address.

    Read the article

  • Starting MySQL database server: mysqld . . . . . . . . . . . . . . failed!

    - by meder
    I restarted my VPS box ( manually/hard restart ) and ever since, mysql fails to start for whatever reason. I did a tail /var/log/syslog and I get this: Feb 20 11:49:33 kyrgyznews mysqld[11461]: ) ;InnoDB: End of page dump 575 Feb 20 11:49:33 kyrgyznews mysqld[11461]: 110220 11:49:33 InnoDB: Page checksum 1045788239, prior-to-4.0.14-form checksum 236985105 576 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: stored checksum 1178062585, prior-to-4.0.14-form stored checksum 236985105 577 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Page lsn 0 10651, low 4 bytes of lsn at page end 10651 578 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Page number (if stored to page already) 3, 579 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: space id (if created with >= MySQL-4.1.1 and stored already) 0 580 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Database page corruption on disk or a failed 581 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: file read of page 3. 582 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: You may have to recover from a backup. 583 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: It is also possible that your operating 584 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: system has corrupted its own file cache 585 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: and rebooting your computer removes the 586 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: error. 587 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: If the corrupt page is an index page 588 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: you can also try to fix the corruption 589 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: by dumping, dropping, and reimporting 590 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: the corrupt table. You can use CHECK 591 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: TABLE to scan your table for corruption. 592 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: See also InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html 593 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: about forcing recovery. 594 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Ending processing because of a corrupt database page. 595 Feb 20 11:49:33 kyrgyznews mysqld_safe[11469]: ended 596 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: 0 processes alive and '/usr/bin/mysqladmin --defaults-file=/etc/mysql/debian.cnf ping' resulted in 597 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: ^G/usr/bin/mysqladmin: connect to server at 'localhost' failed 598 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: error: 'Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2)' 599 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: Check that mysqld is running and that the socket: '/var/run/mysqld/mysqld.sock' exists! 600 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: 601 Feb 20 11:49:56 kyrgyznews mysqld_safe[13437]: started 602 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: The log sequence number in ibdata files does not match 603 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: the log sequence number in the ib_logfiles! 604 Feb 20 11:49:56 kyrgyznews mysqld[13440]: 110220 11:49:56 InnoDB: Database was not shut down normally! 605 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Starting crash recovery. 606 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Reading tablespace information from the .ibd files... 607 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Restoring possible half-written data pages from the doublewrite 608 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: buffer... 609 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Database page corruption on disk or a failed 610 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: file read of page 3. 611 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: You may have to recover from a backup. I have looked at the page it referenced, http://dev.mysql.com/doc/refman/5.0/en/forcing-innodb-recovery.html, but before messing with any settings I was wondering what experienced DBAs would suggest doing? Is there any harm in forcing the recovery? PS - I did not make any updates to mysql. Version is mysql Ver 14.12 Distrib 5.0.51a, for debian-linux-gnu (i486) using readline 5.2.

    Read the article

  • How to disable proxy requests once a server has been added to spammers "open proxy" list?

    - by Matt
    Hello all, I've just started in a new company, and have been going over the setup of their Apache webserver conf files... only to find that they've had their apache servers set up as open proxies available to all the world for the last two months. I've already set ProxyRequests Off in the httpd.conf file and restarted the web server, but the access log file is still growing at a horrendous rate (about a gig a day). I noticed that another question was posted on here about this (http://serverfault.com/questions/63715/apache-hit-with-proxy-request), but their access log was supposedly returning 404 errors, while mine appears to be returning 403 and 404 codes... Is this correct? Here are a few lines out of my access log: 87.118.118.124 - - [16/Mar/2010:10:56:36 -0400] "GET http://www.c5interlude.ru/torrent/viewtopic.php?p=2501 HTTP/1.0" 404 219 "http://www.c5interlude.ru/torrent/viewtopic.php?p=2501" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; .NET CLR 1.1.4322)" 117.41.184.27 - - [16/Mar/2010:10:56:36 -0400] "GET http://ad.xtendmedia.com/st?ad_type=iframe&ad_size=300x250&section=790074 HTTP/1.0" 404 200 "http://www.newbiegamer.com" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.0; Alexa Toolbar)" 122.224.55.222 - - [16/Mar/2010:10:56:36 -0400] "GET http://www.188woool.net/\xb4\xf3\xd4\xcb\xb4\xab\xca\xc0.rar HTTP/1.1" 403 214 "http://www.188woool.net/\xb4\xf3\xd4\xcb\xb4\xab\xca\xc0.rar" "Mozilla/4.0" 58.55.21.40 - - [16/Mar/2010:10:56:36 -0400] "GET http://www.cpx24.com/ad1.js HTTP/1.0" 404 204 "http://thebighits.com/?id=aibux" "Mozilla/4.0 (compatible; MSIE 5.01; Windows NT 5.0)" 122.226.223.188 - - [16/Mar/2010:10:56:36 -0400] "GET http://ad.reduxmedia.com/st?ad_type=iframe&ad_size=160x600&section=798636 HTTP/1.0" 404 200 "http://www.gvvu.com" "Mozilla/4.0 (compatible; MSIE 5.5; AOL 6.0; Windows 98; Win 9x 4.90)" 84.51.109.31 - - [16/Mar/2010:10:56:36 -0400] "GET http://www.kslp.ru/forum/index.php HTTP/1.0" 404 213 "http://www.kslp.ru/forum/index.php" "Mozilla/4.0 (compatible; MSIE 7.0b; Windows NT 6.0 ; .NET CLR 2.0.50215; SL Commerce Client v1.0; Tablet PC 2.0" 122.224.48.49 - - [16/Mar/2010:10:56:36 -0400] "GET http://www1.vip218.com/\xb2\xca\xba\xe7\xb4\xab\xca\xc0.exe HTTP/1.1" 403 214 "http://www1.vip218.com/\xb2\xca\xba\xe7\xb4\xab\xca\xc0.exe" "Mozilla/4.0" 117.41.184.27 - - [16/Mar/2010:10:56:36 -0400] "GET http://ad.xtendmedia.com/st?ad_type=iframe&ad_size=728x90&section=657624 HTTP/1.0" 404 200 "http://www.raiseanimals.com" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98; Alexa Toolbar)" And my corresponding error log entries: [Tue Mar 16 10:56:36 2010] [error] [client 87.118.118.124] File does not exist: C:/public_html/torrent, referer: http://www.c5interlude.ru/torrent/viewtopic.php?p=2501 [Tue Mar 16 10:56:36 2010] [error] [client 117.41.184.27] File does not exist: C:/public_html/st, referer: http://www.newbiegamer.com [Tue Mar 16 10:56:36 2010] [error] [client 122.224.55.222] (22)Invalid argument: Cannot map GET http://www.188woool.net/\xb4\xf3\xd4\xcb\xb4\xab\xca\xc0.rar HTTP/1.1 to file, referer: http://www.188woool.net/\xb4\xf3\xd4\xcb\xb4\xab\xca\xc0.rar [Tue Mar 16 10:56:36 2010] [error] [client 58.55.21.40] File does not exist: C:/public_html/ad1.js, referer: http://thebighits.com/?id=aibux [Tue Mar 16 10:56:36 2010] [error] [client 122.226.223.188] File does not exist: C:/public_html/st, referer: http://www.gvvu.com [Tue Mar 16 10:56:36 2010] [error] [client 84.51.109.31] File does not exist: C:/public_html/forum, referer: http://www.kslp.ru/forum/index.php [Tue Mar 16 10:56:36 2010] [error] [client 122.224.48.49] (22)Invalid argument: Cannot map GET http://www1.vip218.com/\xb2\xca\xba\xe7\xb4\xab\xca\xc0.exe HTTP/1.1 to file, referer: http://www1.vip218.com/\xb2\xca\xba\xe7\xb4\xab\xca\xc0.exe [Tue Mar 16 10:56:36 2010] [error] [client 117.41.184.27] File does not exist: C:/public_html/st, referer: http://www.raiseanimals.com Does this in fact look like the server is blocking them correctly, and is there anything else that I could do better to cut down on my access log size? (perhaps block these requests from the server completely?) Thanks! Matt

    Read the article

  • php-fpm + persistent sockets = 502 bad gateway

    - by leeoniya
    Put on your reading glasses - this will be a long-ish one. First, what I'm doing. I'm building a web-app interface for some particularly slow tcp devices. Opening a socket to them takes 200ms and an fwrite/fread cycle takes another 300ms. To reduce the need for both of these actions on each request, I'm opening a persistent tcp socket which reduces the response time by the aforementioned 200ms. I was hoping PHP-FPM would share the persistent connections between requests from different clients (and indeed it does!), but there are some issues which I havent been able to resolve after 2 days of interneting, reading logs and modifying settings. I have somewhat narrowed it down though. Setup: Ubuntu 13.04 x64 Server (fully updated) on Linode PHP 5.5.0-6~raring+1 (fpm-fcgi) nginx/1.5.2 Relevent config: nginx worker_processes 4; php-fpm/pool.d pm = dynamic pm.max_children = 2 pm.start_servers = 2 pm.min_spare_servers = 2 Let's go from coarse to fine detail of what happens. After a fresh start I have 4x nginx processes and 2x php5-fpm processes waiting to handle requests. Then I send requests every couple seconds to the script. The first take a while to open the socket connection and returns with the data in about 500ms, the second returns data in 300ms (yay it's re-using the socket), the third also succeeds in about 300ms, the fourth request = 502 Bad Gateway, same with the 5th. Sixth request once again returns data, except now it took 500ms again. The process repeats for several cycles after which every 4 requests result in 2x 502 Bad Gateways and 2x 500ms Data responses. If I double all the fpm pool values and have 4x php-fpm processes running, the cycles settles in with 4x successful 500ms responses followed by 4x Bad Gateway errors. If I don't use persistent sockets, this issue goes away but then every request is 500ms. What I suspect is happening is the persistent socket keeps each php-fpm process from idling and ties it up, so the next one gets chosen until none are left and as they error out, maybe they are restarted and become available on the next round-robin loop ut the socket dies with the process. I haven't yet checked the 'slowlog', but the nginx error log shows lots of this: *188 recv() failed (104: Connection reset by peer) while reading response header from upstream, client:... All the suggestions on the internet regarding fixing nginx/php-fpm/502 bad gateway relate to high load or fcgi_pass misconfiguration. This is not the case here. Increasing buffers/sizes, changing timeouts, switching from unix socket to tcp socket for fcgi_pass, upping connection limits on the system....none of this stuff applies here. I've had some other success with setting pm = ondemand rather than dynamic, but as soon as the initial fpm-process gets killed off after idling, the persistent socket is gone for all subsequent php-fpm spawns. For the php script, I'm using stream_socket_client() with a STREAM_CLIENT_PERSISTENT flag. A while/stream_select() loop to detect socket data and fread($sock, 4096) to grab the data. I don't call fclose() obviously. If anyone has some additional questions or advice on how to get a persistent socket without tying up the php-fpm processes beyond the request completion, or maybe some other things to try, I'd appreciate it. some useful links: Nginx + php-fpm - recv() error Nginx + php-fpm "504 Gateway Time-out" error with almost zero load (on a test-server) Nginx + PHP-FPM "error 104 Connection reset by peer" causes occasional duplicate posts http://www.linuxquestions.org/questions/programming-9/php-pfsockopen-552084/ http://stackoverflow.com/questions/14268018/concurrent-use-of-a-persistent-php-socket http://devzone.zend.com/303/extension-writing-part-i-introduction-to-php-and-zend/#Heading3 http://stackoverflow.com/questions/242316/how-to-keep-a-php-stream-socket-alive http://php.net/manual/en/install.fpm.configuration.php https://www.google.com/search?q=recv%28%29+failed+%28104:+Connection+reset+by+peer%29+while+reading+response+header+from+upstream+%22502%22&ei=mC1XUrm7F4WQyAHbv4H4AQ&start=10&sa=N&biw=1920&bih=953&dpr=1

    Read the article

  • XFS disk becomes unavailable after a while

    - by Guard
    Ubuntu 12.04 (but the same was on 11.10 before upgrading) WD MyBook, 2TB, no RAID (or RAID0, not completely sure, anyway no mirroring, both 1TB disks are in use, mounted as a single device). Formatted to XFS, normally used for big movie files. Connected to Firewire 800. At some point the LED started going up and down as when constantly reading/writing. The device gives access error. When unplugged (cable, then holding the power button for a while, then unplugging the power) and re-connected becomes available. xfs_check with no results. xfs_repair did something, but looks like didn't fix any error. Then after a massive read (checking 1.5GB torrent file for integrity) becomes unavailable again. Any ideas what's wrong? Drives? Cables? Motherboard? OS? UPD: not sure how relevant this is, but here are dmesg output [14380.632816] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [14380.633356] SGI XFS Quota Management subsystem [14421.812220] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.890596] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.896858] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14453.895347] firewire_core: created device fw1: GUID 0090a99500a35518, S400, 9 config ROM retries [14453.904818] scsi6 : SBP-2 IEEE-1394 [14453.905014] scsi7 : SBP-2 IEEE-1394 [14454.139993] firewire_sbp2: fw1.0: logged in to LUN 0000 (0 retries) [14454.158769] scsi 6:0:0:0: Direct-Access WD My Book 1015 PQ: 0 ANSI: 4 [14454.159251] sd 6:0:0:0: Attached scsi generic sg3 type 0 [14454.162391] firewire_sbp2: fw1.1: logged in to LUN 0001 (0 retries) [14454.167453] sd 6:0:0:0: [sdc] 3907017568 512-byte logical blocks: (2.00 TB/1.81 TiB) [14454.178822] sd 6:0:0:0: [sdc] Write Protect is off [14454.178826] sd 6:0:0:0: [sdc] Mode Sense: 10 00 00 00 [14454.186830] scsi 7:0:0:1: Enclosure WD My Book Device 1015 PQ: 0 ANSI: 4 [14454.186995] scsi 7:0:0:1: Attached scsi generic sg4 type 13 [14454.190078] sd 6:0:0:0: [sdc] Cache data unavailable [14454.190087] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.202176] sd 6:0:0:0: [sdc] Cache data unavailable [14454.202185] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.239940] sdc: [mac] sdc1 sdc2 sdc3 sdc4 [14454.271262] sd 6:0:0:0: [sdc] Cache data unavailable [14454.271270] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.271354] sd 6:0:0:0: [sdc] Attached SCSI disk [14454.272149] ses 7:0:0:1: Attached Enclosure device [14606.090024] XFS (sdc3): Mounting Filesystem [14612.048343] XFS (sdc3): Starting recovery (logdev: internal) [14620.697636] XFS (sdc3): Ending recovery (logdev: internal) [14748.120957] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [14748.120963] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO [14752.568382] uhci_hcd 0000:00:1a.0: PCI INT A disabled [14752.568579] uhci_hcd 0000:00:1a.1: PCI INT B disabled [14752.568738] ehci_hcd 0000:00:1a.7: PCI INT C disabled [14752.568779] ehci_hcd 0000:00:1a.7: PME# enabled [14752.584526] uhci_hcd 0000:00:1d.1: PCI INT B disabled [14752.584689] uhci_hcd 0000:00:1d.2: PCI INT C disabled [14752.680079] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xe4641000-0xe46413ff] (PCI address [0xe4641000-0xe46413ff]) [14752.680104] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b) [14752.680136] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002) [14752.680170] ehci_hcd 0000:00:1a.7: PME# disabled [14752.680182] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.680190] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [14752.710334] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [14752.710342] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [14752.749186] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [14752.749194] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [14752.790231] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 [14752.790239] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [14752.829170] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.829178] uhci_hcd 0000:00:1d.2: setting latency timer to 64

    Read the article

  • Site-to-site VPN using MD5 instead of SHA and getting regular disconnection

    - by Steven
    We are experiencing some strange behavior with a site-to-site IPsec VPN that goes down about every week for 30 minutes (Iam told 30 minutes exactly). I don't have access to the logs, so it's difficult to troubleshoot. What is also strange is that the two VPN devices are set to use SHA hash algorithm but apparently end up agreeing to use MD5. Does anybody have a clue? or is this just insufficient information? Edit: Here is an extract of the log of one of the two VPN devices, which is a Cisco 3000 series VPN concentrator. 27981 03/08/2010 10:02:16.290 SEV=4 IKE/41 RPT=16120 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27983 03/08/2010 10:02:56.930 SEV=4 IKE/41 RPT=16121 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27986 03/08/2010 10:03:35.370 SEV=4 IKE/41 RPT=16122 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) [… same continues for another 15 minutes …] 28093 03/08/2010 10:19:46.710 SEV=4 IKE/41 RPT=16140 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28096 03/08/2010 10:20:17.720 SEV=5 IKE/172 RPT=1291 xxxxxxxx Group [xxxxxxxx] Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end IS behind a NAT device 28100 03/08/2010 10:20:17.820 SEV=3 IKE/134 RPT=79 xxxxxxxx Group [xxxxxxxx] Mismatch: Configured LAN-to-LAN proposal differs from negotiated proposal. Verify local and remote LAN-to-LAN connection lists. 28103 03/08/2010 10:20:17.820 SEV=4 IKE/119 RPT=1197 xxxxxxxx Group [xxxxxxxx] PHASE 1 COMPLETED 28104 03/08/2010 10:20:17.820 SEV=4 AUTH/22 RPT=1031 xxxxxxxx User [xxxxxxxx] Group [xxxxxxxx] connected, Session Type: IPSec/LAN- to-LAN 28106 03/08/2010 10:20:17.820 SEV=4 AUTH/84 RPT=39 LAN-to-LAN tunnel to headend device xxxxxxxx connected 28110 03/08/2010 10:20:17.920 SEV=5 IKE/25 RPT=1291 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28113 03/08/2010 10:20:17.920 SEV=5 IKE/24 RPT=88 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28116 03/08/2010 10:20:17.920 SEV=5 IKE/66 RPT=1290 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28117 03/08/2010 10:20:17.930 SEV=5 IKE/25 RPT=1292 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28120 03/08/2010 10:20:17.930 SEV=5 IKE/24 RPT=89 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28123 03/08/2010 10:20:17.930 SEV=5 IKE/66 RPT=1291 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28124 03/08/2010 10:20:18.070 SEV=4 IKE/173 RPT=17330 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices. 28127 03/08/2010 10:20:18.070 SEV=4 IKE/49 RPT=17332 xxxxxxxx Group [xxxxxxxx] Security negotiation complete for LAN-to-LAN Group (xxxxxxxx) Responder, Inbound SPI = 0x56a4fe5c, Outbound SPI = 0xcdfc3892 28130 03/08/2010 10:20:18.070 SEV=4 IKE/120 RPT=17332 xxxxxxxx Group [xxxxxxxx] PHASE 2 COMPLETED (msgid=37b3b298) 28131 03/08/2010 10:20:18.750 SEV=4 IKE/41 RPT=16141 xxxxxxxx Group [xxxxxxxx] IKE Initiator: New Phase 2, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28135 03/08/2010 10:20:18.870 SEV=4 IKE/173 RPT=17331 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices.

    Read the article

  • Outlook 2007 Does Not Accept Login Credentials, OWA Webmail Does. Troubleshooting Advice?

    - by Chris
    I am trying to connect Outlook 2007 to Exchange (Hosted Exchange from Rackspace). Soon, I will need to roll this out for our entire office. With the Exchange account added to Outlook, Outlook starts up and asks for the user's username and password. Unfortunately, it doesn't like the password I use for it. I can confirm this username (email address) and password combo works by using Outlook WebMail, and another user (in another network/office) confirmed the Exchange account does work within his Outlook client. In my network/office, I can confirm that an Outlook 2007 client (under Windows 7) can connect to the Hosted Exchange server from Rackspace. However, I have not been able to get Outlook 2007 (under Windows XP SP3) to connect to the very same Exchange server Outlook 2007 (under Windows 7) can connect to. Outlook continuously prompts me for the username and password and does not accept the correct combination. Now, regarding the Outlook client that cannot connect/login to Exchange: The user has full admin rights on the workstation We do not run a domain controller/LDAP The firewall on the workstation has been disabled Real time file scanning in Microsoft Security Essentials has been disabled There are no virus scanning applications that would interface with Outlook or an email server. The Exchange account is setup to run on a newly created Outlook profile The network firewall does not log any blocked attempts A packet capture at the router reveals communication between the workstation and the Exchange server or proxy (though, this is SSL encrypted, so I don't know what the computers are saying) I have applied a fix (Added DWORD value of 0 for DefConnectOpts under HKEY_CURRENT_USER\Software\Microsoft\Office\12.0\Outlook\RPC) that was recommended to make RPC function when the workstation does not have a default gateway set. Workstation is configured as DHCP. This fix did nothing, and it may be worth noting the RPC subkey was not present until I added it. RPC service is running on the workstation The program is not running under any compatibility mode. Side note: Outlook 2007 installs with compatibility mode for XP enabled by default in windows 7. Outlook 2007 will not even try to connect to exchange if this compatibility mode is checked. In windows xp, I tried checking compatibility mode for windows 2000, and was unable to connect to exchange as well. Here is the specific configuration I've used in a blank outlook profile: Microsoft Exchange Server: ##MASKED##-MBX-C18.mex07a.mlsrvr.com Username: (Full Email Address: [email protected]) Password: ##MASKED## Outlook Anywhere: Connect to Microsoft Exchange using HTTP Exchange Proxy Settings: Proxy Server: mex07a.emailsrvr.com Check "Connect using SSL only" Under "Only connect to proxy servers...", enter: msstd:mex07a.emailsrvr.com Check "On fast networks, connect using HTTP first, then connect using TCP/IP" Check "On slow networks, connect using HTTP first, then connect using TCP/IP" Proxy authentication settings: Basic Authentication Notes: mex07a.mlsrvr.com and mex07a.emailsrvr.com may look incorrect at first glance, but this is not a typo - these instructions were handed down from rackspace and are confirmed to be working, just not on this workstation. I have tried to use the RpcPing utility but must have been using it wrong. I got as far as "Bad Interface Descriptor". It would seem to me getting Outlook and Exchange to work together would be a breeze, especially since everything is done over port 80 with web services. Unfortunately, the user is stuck with WebMail access only, because Outlook won't accept the Exchange credentials. Do you have any ideas of other things I could try to debug this issue further? Any and all help is greatly appreciated. Thank you! -Chris

    Read the article

  • BluRay audio/video stuttering with PowerDVD 11, WinDVD 11 Pro, etc? Xonar/Auzen HD audio option?

    - by jrista
    I recently upgraded my Windows 7 MediaCenter HTPC due to a motherboard failure (really old motherboard and cpu, it was on its last legs.) I chose to upgrade to an i5 system with everything built into the motherboard. I did my due diligence, researched, and found some hardware that was within my budget. I ended up with: Core i5 2500K (3.3Ghz) Corsair XMS3 2x2Gb DDR3 (4Gb) ASUS P8H 61-M LE/CSM MicroCenter 64Gb SSD (Previous BluRay player, forget the brand) The system is pretty awesome, and plays everything I have perfectly. I almost went with an Atom solution, however there have been numerous notes that they do not play NetFlix Instant Watch well...and I am a heavy Netflix IW user. High definition BluRay rips work well, although they usually contain lower audio quality than the BluRay's they were ripped from. The real problem I am encountering is playing back BluRay video from discs. For some reason, I am encountering rather terrible stuttering problems with both the audio and video. The stuttering is synchronous in both, and occurs at seemingly random intervals. I've used PowerDVD 9, PowerDVD 11 trial, and WinDVD 11 Pro trial. All three have stuttering problems, although PowerDVD 11 seems to have the least. Watching system resource usage, CPU load is never above 20%, and memory usage tends to be a constant 1/3rd the total available system memory. When playback is fine, its superb...the video is crystal clear. The audio quality is ok, certainly not what I would expect from a BluRay disc. I did some research, and it seems that playing BluRay from a PC causes a downsampling of the audio? I am curious if the audio is my primary problem here, the cause of the stuttering I am encountering? When stuttering occurs, the audio gets REALLY bad, while the video just pauses momentarily every second until for whatever reason everything picks up and runs fine (usually after a few seconds to a couple minutes.) The audio chipset is a Realtek HD ALC887 8-channel, supposedly designed to support BluRay playback. Has anyone encountered any issues like this playing back bluray discs on a PC (namely with PowerDVD...WinDVD was FAR worse, and seemed to have real trouble even reading the discs, and I have no interest in fiddling with it further.) Is there any reason to suspect the video decoding as the problem?(Given how bad the audio gets during a stutter, and how clean the video remains, I am inclined to think the issue boils down to audio.) Is it even remotely possible that the motherboard, cpu, or ram are causing the stuttering (all three are pretty blazing fast...faster than the hardware that I replaced, which seemed to play BluRay fine with PowerDVD 9.) I've read a bit about the Asus Xonar HDAV 1.3 and the Auzen X-Fi HomeTheater HD home theater hi-fi audio cards. Seems they are the only way to get true full-quality, uncompressed BluRay audio bitstreaming over HDMI on a PC. None of the usual suspects seem to have these cards in stock, however. Are these cards worth getting? Are they even still available, or have they been discontinued (if so, that would indeed be sad...they sound simply fantastic.)

    Read the article

  • Call to daemon in a /etc/init.d script is blocking, not running in background

    - by tony
    I have a Perl script that I want to daemonize. Basically this perl script will read a directory every 30 seconds, read the files that it finds and then process the data. To keep it simple here consider the following Perl script (called synpipe_server, there is a symbolic link of this script in /usr/sbin/) : #!/usr/bin/perl use strict; use warnings; my $continue = 1; $SIG{'TERM'} = sub { $continue = 0; print "Caught TERM signal\n"; }; $SIG{'INT'} = sub { $continue = 0; print "Caught INT signal\n"; }; my $i = 0; while ($continue) { #do stuff print "Hello, I am running " . ++$i . "\n"; sleep 3; } So this script basically prints something every 3 seconds. Then, as I want to daemonize this script, I've also put this bash script (also called synpipe_server) in /etc/init.d/ : #!/bin/bash # synpipe_server : This starts and stops synpipe_server # # chkconfig: 12345 12 88 # description: Monitors all production pipelines # processname: synpipe_server # pidfile: /var/run/synpipe_server.pid # Source function library. . /etc/rc.d/init.d/functions pname="synpipe_server" exe="/usr/sbin/synpipe_server" pidfile="/var/run/${pname}.pid" lockfile="/var/lock/subsys/${pname}" [ -x $exe ] || exit 0 RETVAL=0 start() { echo -n "Starting $pname : " daemon ${exe} RETVAL=$? PID=$! echo [ $RETVAL -eq 0 ] && touch ${lockfile} echo $PID > ${pidfile} } stop() { echo -n "Shutting down $pname : " killproc ${exe} RETVAL=$? echo if [ $RETVAL -eq 0 ]; then rm -f ${lockfile} rm -f ${pidfile} fi } restart() { echo -n "Restarting $pname : " stop sleep 2 start } case "$1" in start) start ;; stop) stop ;; status) status ${pname} ;; restart) restart ;; *) echo "Usage: $0 {start|stop|status|restart}" ;; esac exit 0 So, (if I have well understood the doc for daemon) the Perl script should run in the background and the output should be redirected to /dev/null if I execute : service synpipe_server start But here is what I get instead : [root@master init.d]# service synpipe_server start Starting synpipe_server : Hello, I am running 1 Hello, I am running 2 Hello, I am running 3 Hello, I am running 4 Caught INT signal [ OK ] [root@master init.d]# So it starts the Perl script but runs it without detaching it from the current terminal session, and I can see the output printed in my console ... which is not really what I was expecting. Moreover, the PID file is empty (or with a line feed only, no pid returned by daemon). Does anyone have any idea of what I am doing wrong ? EDIT : maybe I should say that I am on a Red Hat machine. Scientific Linux SL release 5.4 (Boron) Would it do the job if instead of using the daemon function, I use something like : nohup ${exe} >/dev/null 2>&1 & in the init script ?

    Read the article

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • How to stop Apache from crashing my entire server?

    - by CyberShadow
    I maintain a Gentoo server with a few services, including Apache. It's fairly low-end (2GB of RAM and a low-end CPU with 2 cores). My problem is that, despite my best efforts, an over-loaded Apache crashes the entire server. In fact, at this point I'm close to being convinced that Linux is a horrible operating system that isn't worth anyone's time looking for stability under load. Things I tried: Adjusting oom_adj for the root Apache process (and thus all its children). That had close to no effect. When Apache was overloaded it would bring the system to a grind, as the system paged out everything else before it got to kill anything. Turning off swap. Didn't help, it would unload memory paged to binaries of processes and other files on /, thus causing the same effect. Putting it in a memory-limited cgroup (limited to 512 MB of RAM, 1/4th of the total). This "worked", at least in my own stress tests - except the server keeps crashing under load (basically stalling all other processes, inaccessible via SSH, etc.) Running it with idle I/O priority. This wasn't a very good idea in the end, because it just caused the system load to climb indefinitely (into the thousands) with almost no visible effect - until you tried to access an unbuffered part of the disk. This caused the task to freeze. (So much for good I/O scheduling, eh?) Limiting the number of concurrent connections to Apache. Setting the number too low caused web sites to become unresponsive due to most slots being occupied with long requests (file downloads). I tried various Apache MPMs without much success (prefork, event, itk). Switching from prefork/event+php-cgi+suphp to itk+mod_php. This improved performance, but didn't solve the actual problem. Switching I/O schedulers (cfq to deadline). Just to stress this out: I don't care if Apache itself goes down under load, I just want the rest of my system to remain stable. Of course, having Apache recover quickly after a brief period of intensive load would be great to have, but one step at a time. Right now I am mostly dumbfounded by how can humanity, in this day and age, design an operating system where such a seemingly simple task (don't allow one system component to crash the entire system) seems practically impossible - or at least, very hard to do. Please don't suggest things like VMs or "BUY MORE RAM". Some more information gathered with a friend's help: The processes hang when the cgroup oom killer is invoked. Here's the call trace: [<ffffffff8104b94b>] ? prepare_to_wait+0x70/0x7b [<ffffffff810a9c73>] mem_cgroup_handle_oom+0xdf/0x180 [<ffffffff810a9559>] ? memcg_oom_wake_function+0x0/0x6d [<ffffffff810aa041>] __mem_cgroup_try_charge+0x32d/0x478 [<ffffffff810aac67>] mem_cgroup_charge_common+0x48/0x73 [<ffffffff81081c98>] ? __lru_cache_add+0x60/0x62 [<ffffffff810aadc3>] mem_cgroup_newpage_charge+0x3b/0x4a [<ffffffff8108ec38>] handle_mm_fault+0x305/0x8cf [<ffffffff813c6276>] ? schedule+0x6ae/0x6fb [<ffffffff8101f568>] do_page_fault+0x214/0x22b [<ffffffff813c7e1f>] page_fault+0x1f/0x30 At this point, the apache memory cgroup is practically deadlocked, and burning CPU in syscalls (all with the above call trace). This seems like a problem in the cgroup implementation...

    Read the article

  • Bonding: works only for download

    - by Crazy_Bash
    I would like to install bonding with 4 links with mode 4. but only "download/receiving" works with bondig. for transmitting the system chooses one link. ifconfig bond0 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 inet addr:ip Bcast:ip Mask:255.255.255.248 inet6 addr: fe80::92e2:baff:fe0f:76b4/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:239187413 errors:0 dropped:10944 overruns:0 frame:0 TX packets:536902370 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14688536197 (13.6 GiB) TX bytes:799521192901 (744.6 GiB) eth2 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:54969488 errors:0 dropped:0 overruns:0 frame:0 TX packets:2537 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3374778591 (3.1 GiB) TX bytes:314290 (306.9 KiB) eth3 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:64935805 errors:0 dropped:1 overruns:0 frame:0 TX packets:2532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3993499746 (3.7 GiB) TX bytes:313968 (306.6 KiB) eth4 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:57352105 errors:0 dropped:2 overruns:0 frame:0 TX packets:536894778 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3524236530 (3.2 GiB) TX bytes:799520265627 (744.6 GiB) eth5 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:61930025 errors:0 dropped:3 overruns:0 frame:0 TX packets:2540 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3796021948 (3.5 GiB) TX bytes:314274 (306.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5320 (5.1 KiB) TX bytes:5320 (5.1 KiB) those are my configs: DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2 (0) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 802.3ad info LACP rate: slow Aggregator selection policy (ad_select): stable Active Aggregator Info: Aggregator ID: 1 Number of ports: 4 Actor Key: 17 Partner Key: 11 Partner Mac Address: 00:24:51:12:63:00 Slave Interface: eth2 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b4 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b5 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b6 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b7 Aggregator ID: 1 Slave queue ID: 0 /etc/modprobe.d/bonding.conf alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 Linux: Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux what i've tried: downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 mode 6

    Read the article

  • Issues configuring Exchange 2010 as well as SSL problems.

    - by Eric Smith
    Possibly-Relevant Background Info: I've recently moved up from icky shared hosting to a glorious, Remote Desktop-administrated VPS server running Windows Server 2008 R2. Even though I'm only 21 now and a computer science major, I've tried to play with every Windows Server release since '03, just to learn new things. What usually happens is inevitably I'll do something wrong and pretty much ruin the install. You're dealing with an amateur here :) Through the past few months of working with my new server, I've mastered DNS, IIS, got Team Foundation Server running (yay!), and can install all of the other basics like SQL Server and Active Directory. The Problem: Now, these last few weeks I've been trying to install Exchange Server 2010 (SP1). To make a long story short, it took me several attempts, and I even had to get my server wiped just so I could start fresh since Exchange decided uninstalling properly was for sissies (cost me $20, bah). Today, at long last, I got Exchange mostly working. There were two main problems left, however, that left me unsatisfied: Exchange installed itself and all of its child sites into Default Web Site. I wanted to access Exchange via mail.domain.com, but instead everything was configured to domain.com. My limited server admin knowledge was not enough to configure IIS or Exchange to move itself over to the website I had set up for it, appropriately titled 'mail.domain.com', which I had bound to a dedicated IP address (I was told this was necessary, but he may have been wrong). I have two SSL certificates: one for my main domain and one for my mail subdomain. For whatever reason, I had issues geting Exchange to use my mail certificate, even though I had assigned the proper roles in the MMC. I did, at one point, get it to work (or mostly work, anyways. Frankly, my memory of today is clouded by intense frustration). Additionally, I was confused which type of SSL certificate I should be using for Exchange. My SSL provider, GoDaddy, allows me to request a new certificate whenever, so I can use either the certificate request provided by IIS or the more complicated and specific request you can create with Exchange. Which type should I be using, the IIS or Exchange certificate? If I must use the Exchange certificate, will that 1) cause issues when I bind that certificate to my mail.domain.com subdomain or 2) is that an unnecessary step? The SSL Certificate Strikes Back When I thought I had the proper SSL certificate assigned for those brief, sweet moments, Google Chrome reported the correct mail.domain.com certificate when browsing https://mail.domain.com. However, Outlook 2010 threw up an error when trying to configure my email account claiming that the certificate didn't match the domain of "mail.domain.com". Is this an issue that will be resolved by problem #2 or is it a separate one entirely? Apologies for the massive wall of text, but I wanted to provide as much info as I possibly could. Exchange is the last thing I'd like installed on my server, and naturally it's turning out to be the hardest. Thanks for any info at all. Even a point in a vague direction would be a huge help at this point. Thanks! -Eric P.S.: The reason I keep ruining my install is that when I attempt to uninstall Exchange, something invariably goes wrong. The last time the uninstaller complained that there was still a mailbox active and it couldn't proceed until I deleted it. ... The only mailbox left was the Administrator account, the built-in one I couldn't delete. So I attempted to manually uninstall it following several guides online only to now be stuck unable to launch the installer and have to get my system wiped AGAIN for the second time today ($40 down the drain, bah!). I do not understand at all why "uninstall" just can't mean "hey, you, delete everything and go away". There's not even a force uninstall option, only a "recover system" option that just fails to fix anything and makes it so I can't even use the GUI uninstaller. </rant>

    Read the article

  • Rails app deployment challenge, not finding database table in production.log

    - by Stefan M
    I'm trying to setup PasswordPusher as my first ruby app ever. Building and running the webrick server as instructed in README works fine. It was only when I tried to add Apache ProxyPass and ProxyPassReverse that the page load slowed down to several minutes. So I gave mod_passenger a whirl but now it's unable to find the password table. Here's what I get in log/production.log. Started GET "/" for 10.10.2.13 at Sun Jun 10 08:07:19 +0200 2012 Processing by PasswordsController#new as HTML Completed 500 Internal Server Error in 1ms ActiveRecord::StatementInvalid (Could not find table 'passwords'): app/controllers/passwords_controller.rb:77:in `new' app/controllers/passwords_controller.rb:77:in `new' While in log/private.log I get a lot more output so here's just a snippet but it looks to me like it's working with the database. Edit: This was actually old log output, maybe from db:create. Migrating to AddUserToPassword (20120220172426) (0.3ms) ALTER TABLE "passwords" ADD "user_id" integer (0.0ms) PRAGMA index_list("passwords") (0.2ms) CREATE INDEX "index_passwords_on_user_id" ON "passwords" ("user_id") (0.7ms) INSERT INTO "schema_migrations" ("version") VALUES ('20120220172426') (0.1ms) select sqlite_version(*) (0.1ms) SELECT "schema_migrations"."version" FROM "schema_migrations" (0.0ms) PRAGMA index_list("passwords") (0.0ms) PRAGMA index_info('index_passwords_on_user_id') (4.6ms) PRAGMA index_list("rails_admin_histories") (0.0ms) PRAGMA index_info('index_rails_admin_histories') (0.0ms) PRAGMA index_list("users") (4.8ms) PRAGMA index_info('index_users_on_unlock_token') (0.0ms) PRAGMA index_info('index_users_on_reset_password_token') (0.0ms) PRAGMA index_info('index_users_on_email') (0.0ms) PRAGMA index_list("views") In my vhost I have it set to use RailsEnv private. <VirtualHost *:80> # ProxyPreserveHost on # # ProxyPass / http://10.220.100.209:180/ # ProxyPassReverse / http://10.220.100.209:180/ DocumentRoot /var/www/pwpusher/public <Directory /var/www/pwpusher/public> allow from all Options -MultiViews </Directory> RailsEnv private ServerName pwpush.intranet ErrorLog /var/log/apache2/error.log LogLevel debug CustomLog /var/log/apache2/access.log combined </VirtualHost> My passenger.conf in mods-enabled is default for Debian. <IfModule mod_passenger.c> PassengerRoot /usr PassengerRuby /usr/bin/ruby </IfModule> In the apache error.log I get something more cryptic to me. [Sun Jun 10 06:25:07 2012] [notice] Apache/2.2.16 (Debian) Phusion_Passenger/2.2.11 PHP/5.3.3-7+squeeze9 with Suhosin-Patch mod_ssl/2.2.16 OpenSSL/0.9.8o configured -- resuming normal operations /var/www/pwpusher/vendor/bundle/ruby/1.8/bundler/gems/modernizr-rails-09e9e6a92d67/lib/modernizr/rails/version.rb:3: warning: already initialized constant VERSION cache: [GET /] miss [Sun Jun 10 08:07:19 2012] [debug] mod_deflate.c(615): [client 10.10.2.13] Zlib: Compressed 728 to 423 : URL / /var/www/pwpusher/vendor/bundle/ruby/1.8/bundler/gems/modernizr-rails-09e9e6a92d67/lib/modernizr/rails/version.rb:3: warning: already initialized constant VERSION cache: [GET /] miss [Sun Jun 10 10:17:16 2012] [debug] mod_deflate.c(615): [client 10.10.2.13] Zlib: Compressed 728 to 423 : URL / Maybe that's routine stuff. I can see the rake command create files in the relative app root db/. I have private.sqlite3, production.sqlite3 among others. And here's my config/database.yml. base: &base adapter: sqlite3 timeout: 5000 development: database: db/development.sqlite3 <<: *base test: database: db/test.sqlite3 <<: *base private: database: db/private.sqlite3 <<: *base production: database: db/production.sqlite3 <<: *base I've tried setting absolute paths in it but that did not help.

    Read the article

  • iptables - quick safety eval & limit max conns over time

    - by Peter Hanneman
    Working on locking down a *nix server box with some fancy iptable(v1.4.4) rules. I'm approaching the matter with a "paranoid, everyone's out to get me" style, not necessarily because I expect the box to be a hacker magnet but rather just for the sake of learning iptables and *nix security more throughly. Everything is well commented - so if anyone sees something I missed please let me know! The *nat table's "--to-ports" point to the only ports with actively listening services. (aside from pings) Layer 2 apps listen exclusively on chmod'ed sockets bridged by one of the layer 1 daemons. Layers 3+ inherit from layer 2 in a similar fashion. The two lines giving me grief are commented out at the very bottom of the *filter rules. The first line runs fine but it's all or nothing. :) Many thanks, Peter H. *nat #Flush previous rules, chains and counters for the 'nat' table -F -X -Z #Redirect traffic to alternate internal ports -I PREROUTING --src 0/0 -p tcp --dport 80 -j REDIRECT --to-ports 8080 -I PREROUTING --src 0/0 -p tcp --dport 443 -j REDIRECT --to-ports 8443 -I PREROUTING --src 0/0 -p udp --dport 53 -j REDIRECT --to-ports 8053 -I PREROUTING --src 0/0 -p tcp --dport 9022 -j REDIRECT --to-ports 8022 COMMIT *filter #Flush previous settings, chains and counters for the 'filter' table -F -X -Z #Set default behavior for all connections and protocols -P INPUT DROP -P OUTPUT DROP -A FORWARD -j DROP #Only accept loopback traffic originating from the local NIC -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j DROP #Accept all outgoing non-fragmented traffic having a valid state -A OUTPUT ! -f -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT #Drop fragmented incoming packets (Not always malicious - acceptable for use now) -A INPUT -f -j DROP #Allow ping requests rate limited to one per second (burst ensures reliable results for high latency connections) -A INPUT -p icmp --icmp-type 8 -m limit --limit 1/sec --limit-burst 2 -j ACCEPT #Declaration of custom chains -N INSPECT_TCP_FLAGS -N INSPECT_STATE -N INSPECT #Drop incoming tcp connections with invalid tcp-flags -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL ALL -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL NONE -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,FIN FIN -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,PSH PSH -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,URG URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL FIN,PSH,URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags FIN,RST FIN,RST -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags SYN,RST SYN,RST -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL SYN,FIN,PSH,URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL SYN,RST,ACK,FIN,URG -j DROP #Accept incoming traffic having either an established or related state -A INSPECT_STATE -m state --state ESTABLISHED,RELATED -j ACCEPT #Drop new incoming tcp connections if they aren't SYN packets -A INSPECT_STATE -m state --state NEW -p tcp ! --syn -j DROP #Drop incoming traffic with invalid states -A INSPECT_STATE -m state --state INVALID -j DROP #INSPECT chain definition -A INSPECT -p tcp -j INSPECT_TCP_FLAGS -A INSPECT -j INSPECT_STATE #Route incoming traffic through the INSPECT chain -A INPUT -j INSPECT #Accept redirected HTTP traffic via HA reverse proxy -A INPUT -p tcp --dport 8080 -j ACCEPT #Accept redirected HTTPS traffic via STUNNEL SSH gateway (As well as tunneled HTTPS traffic destine for other services) -A INPUT -p tcp --dport 8443 -j ACCEPT #Accept redirected DNS traffic for NSD authoritative nameserver -A INPUT -p udp --dport 8053 -j ACCEPT #Accept redirected SSH traffic for OpenSSH server #Temp solution: -A INPUT -p tcp --dport 8022 -j ACCEPT #Ideal solution: #Limit new ssh connections to max 10 per 10 minutes while allowing an "unlimited" (or better reasonably limited?) number of established connections. #-A INPUT -p tcp --dport 8022 --state NEW,ESTABLISHED -m recent --set -j ACCEPT #-A INPUT -p tcp --dport 8022 --state NEW -m recent --update --seconds 600 --hitcount 11 -j DROP COMMIT *mangle #Flush previous rules, chains and counters in the 'mangle' table -F -X -Z COMMIT

    Read the article

  • Did a recent WinXP update break CD/DVD read speeds? SP2/SP3

    - by quack quixote
    I have two systems with fresh installations of Windows XP Pro SP3 (SP3 slipstreamed into the installer; fully updated after install). One's a refurbished 2.4GHz Pentium4 system; the other is a new 1.6GHz Atom330 build. Both have brand-new dual-layer CD/DVD burners (one's a LiteOn IDE, the other an LG SATA). Both take a really looooong time to read a single-layer DVD in Windows with Cygwin tools. Specifically, 40 minutes or more. I burn backup data to single-layer DVD+/-R and use MD5 hashes for data verification (made with the standard md5sum tool in Unix or Cygwin). The hashes are burned to disc with the data files, and I use this command to verify: $ cd /path/to/disc/mountpoint ; time md5sum -c < md5.txt Here's how long that takes to run on a full single-layer DVD+/-R disc: Old system (WinXP SP2, 1.8GHz Athlon 2500+, last summer): ~10 minutes Old system (Ubuntu 9.04, 1.8GHz Athlon 2500+): ~10 minutes Old system (Debian 5, dual 550MHz P3): ~10 minutes New Pentium4 system (running Ubuntu 9.04): ~5 minutes New Pentium4 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes New Atom330 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes Now the weird stuff: Old system (WinXP SP2, 1.8GHz Athlon 2500+, today): ~25 minutes New Pentium4 system (running WinXP SP3, read from Cygwin): ~40-50 minutes (?!!) New Atom330 system (running WinXP SP3, read from Cygwin): ~40 minutes (can do it in ~30 minutes ...if i have another program spin up the drive first) Since both systems will copy files in 6 minutes using Windows Explorer, I know it's not a hardware problem. Windows just never spins up the drive during the Cygwin read, so it stays super-slow the whole time. Other programs like EAC and DVD Decrypter seem to spin up the disc just fine during their processing. DMA is enabled on both systems. (Can confirm in Windows' Device Manager on the Atom330, not on the P4.) Nero's DriveSpeed tool doesn't seem to have any effect. Copy times are comparable from commandline with Windows' xcopy. Copying with Cygwin's cp looks more like the problem state -- it will spin up the drive for a short time, never reaches full speed, and lets it spin back down again for most of the copy. What I need is to get full read speeds from Cygwin. Is this a known issue with SP3 or some other recent Windows update? Any other ideas? Update: More testing; Windows will spin up the drive when data is copied with Windows tools, but not when read in place or copied with Cygwin tools. It doesn't make sense to me that Windows spins up the drive for copying, but not for other reads. Might be more of a Cygwin problem? Update 2: GUI activity is sluggish during the problem state -- during the Cygwin verifies, there's a slight but noticable delay when dragging windows or icons around on the desktop, switching windows, Alt-Tabbing through open applications, opening new windows, etc. It reminds me of the delay when opening a Windows Explorer window on My Computer just after inserting a DVD. I've tried updating Cygwin (from 1.5.x to 1.7.x), but no change in the problem behavior. I've also noticed this issue occurs on WinXP SP2, but it's not exactly the same -- some spin-up occurs, so the read happens in ~25-30 minutes instead of 40+. The SP2 system used to run the verifies in ~10 minutes, and when it first changed (not sure exactly when, maybe in late November or early December 2009) I thought it was dying hardware. This is why I suspect an official update of breaking this functionality; this has worked for years on that SP2 box.

    Read the article

  • Error during GENERAL_REQUEST_ENTITY for POST results in ASP .NET session state never getting unlocked

    - by Jesse
    I have been trying to chase down the root cause of a condition where ASP .NET session state remains locked after a web request has been terminated due to an unexpected error. We use the SQL Server session state provider for session because we have several servers in a web farm. This issue first presented itself in the form of many requests getting stuck on the 'AcquireRequestState' event of their lifecycle for no apparent reason. I was able to finding corresponding entries for these requests in the session state database in SQL server that were all locked (column Locked = 1). I was also able to correlate these requests to entries in the IIS log with HTTP status codes of 500 (with a sub status of 0). These findings lead me to believe that, in some cases, a request was erroring out but was NOT releasing its lock on session state like it should. I enabled Failed Request Tracing in IIS for the website in question for status code 500 with all available providers selected each with the 'Verbose' setting for verbosity. I've since gathered several failed traces that have caused permanently locked ASP .NET sessions. They all share the same characteristics: They are all 'POST' requests where the browser is posting data to be processed/saved. They all have events indicating that the 'Session' module was invoked during the REQUEST_ACQUIRE_STATE event. At this point the request would have marked the row in the session state database as being "locked". This is normal and expected. They all have GENERAL_READ_ENTITY_START, GENERAL_READ_ENTITY_END, and GENERAL_REQUEST_ENTITY entries that appear to be reading in the data that was posted to the server as part of the request. This appears to be a buffered operation as these events get repeated over and over with each one reading in some subset of the posted data. At some point during the 'read entity' related events and error occurs. Some have the error code "Incorrect function. (0x80070001)" and others have "The I/O operation has been aborted because of either a thread exit or an application request. (0x800703e3)". Once the error has been encountered, they all jump directly to the END_REQUEST events. The issue here is that, under normal circumstances, there should be a RELEASE_REQUEST_STATE event that will allow the Session module to release the lock it has on the session. This event is being skipped in this scenario. Just to be sure, I enabled failed request tracing for the '200' status code as well and generated several traces of successful requests that do have the RELEASE_REQUEST_STATE event being handled by the Session module. My theory at this point is that some kind of network issue is causing the 'Incorrect function' and 'I/O operation has been aborted because of either a thread exit or an application request' errors, but I don't understand why this seems to be causing the request handling to skip over the RELEASE_REQUEST_STATE event. If the request went through REQUEST_ACQUIRE_STATE it seems like it should also hit RELEASE_REQUEST_STATE as well. I'm loathe to say that this is a bug in IIS or ASP .NET, but it certainly appears that way to me at this point. Are there any configuration changes I could make to help ensure that 'RELEASE_REQUEST_STATE' is fired under all error conditions?

    Read the article

  • Set up lnux box for hosting a-z

    - by microchasm
    I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project The above upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Create a chroot jail to hold sftp user via rssh. This will force SCP/SFTP and will circumvent traditional FTP server setup. #cd /tmp #wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm #rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm #useradd -m -d /home/dev -s /usr/bin/rssh dev #passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. #vi /etc/rssh.conf Uncomment line allowscp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). Above instructions for SFTP appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

    Read the article

  • "Possible SYN flooding" in log despite low number of SYN_RECV connections

    - by al4
    Recently we had an apache server which was responding very slowly due to SYN flooding. The workaround for this was to enable tcp_syncookies (net.ipv4.tcp_syncookies=1 in /etc/sysctl.conf). I posted a question about this here if you want more background. After enabling syncookies we started seeing the following message in /var/log/messages approximately every 60 seconds: [84440.731929] possible SYN flooding on port 80. Sending cookies. Vinko Vrsalovic informed me that this means the syn backlog is getting full, so I raised tcp_max_syn_backlog to 4096. At some point I also lowered tcp_synack_retries to 3 (down from the default of 5) by issuing sysctl -w net.ipv4.tcp_synack_retries=3. After doing this, the frequency seemed to drop, with the interval of the messages varying between roughly 60 and 180 seconds. Next I issued sysctl -w net.ipv4.tcp_max_syn_backlog=65536, but am still getting the message in the log. Throughout all this I've been watching the number of connections in SYN_RECV state (by running watch --interval=5 'netstat -tuna |grep "SYN_RECV"|wc -l'), and it never goes higher than about 240, much much lower than the size of the backlog. Yet I have a Red Hat server which hovers around 512 (limit on this server is the default of 1024). Are there any other tcp settings which would limit the size of the backlog or am I barking up the wrong tree? Should the number of SYN_RECV connections in netstat -tuna correlate to the size of the backlog? Update As best I can tell I'm dealing with legitimate connections here, netstat -tuna|wc -l hovers around 5000. I've been researching this today and found this post from a last.fm employee, which has been rather useful. I've also discovered that the tcp_max_syn_backlog has no effect when syncookies are enabled (as per this link) So as a next step I set the following in sysctl.conf: net.ipv4.tcp_syn_retries = 3 # default=5 net.ipv4.tcp_synack_retries = 3 # default=5 net.ipv4.tcp_max_syn_backlog = 65536 # default=1024 net.core.wmem_max = 8388608 # default=124928 net.core.rmem_max = 8388608 # default=131071 net.core.somaxconn = 512 # default = 128 net.core.optmem_max = 81920 # default = 20480 I then setup my response time test, ran sysctl -p and disabled syncookies by sysctl -w net.ipv4.tcp_syncookies=0. After doing this the number of connections in the SYN_RECV state still remained around 220-250, but connections were starting to delay again. Once I noticed these delays I re-enabled syncookies and the delays stopped. I believe what I was seeing was still an improvement from the initial state, however some requests were still delayed which is much worse than having syncookies enabled. So it looks like I'm stuck with them enabled until we can get some more servers online to cope with the load. Even then, I'm not sure I see a valid reason to disable them again as they're only sent (apparently) when the server's buffers get full. But the syn backlog doesn't appear to be full with only ~250 connections in the SYN_RECV state! Is it possible that the SYN flooding message is a red herring and it's something other than the syn_backlog that's filling up? If anyone has any other tuning options I haven't tried yet I'd be more than happy to try them out, but I'm starting to wonder if the syn_backlog setting isn't being applied properly for some reason.

    Read the article

  • unattended-upgrades does not reboot

    - by Cheiron
    I am running Debian 7 stable with unattended-upgrades (every morning at 6 AM) to make sure I am always fully updated. I have the following config: $ cat /etc/apt/apt.conf.d/50unattended-upgrades // Automatically upgrade packages from these origin patterns Unattended-Upgrade::Origins-Pattern { // Archive or Suite based matching: // Note that this will silently match a different release after // migration to the specified archive (e.g. testing becomes the // new stable). "o=Debian,a=stable"; "o=Debian,a=stable-updates"; // "o=Debian,a=proposed-updates"; "origin=Debian,archive=stable,label=Debian-Security"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { // "vim"; // "libc6"; // "libc6-dev"; // "libc6-i686"; }; // This option allows you to control if on a unclean dpkg exit // unattended-upgrades will automatically run // dpkg --force-confold --configure -a // The default is true, to ensure updates keep getting installed //Unattended-Upgrade::AutoFixInterruptedDpkg "false"; // Split the upgrade into the smallest possible chunks so that // they can be interrupted with SIGUSR1. This makes the upgrade // a bit slower but it has the benefit that shutdown while a upgrade // is running is possible (with a small delay) //Unattended-Upgrade::MinimalSteps "true"; // Install all unattended-upgrades when the machine is shuting down // instead of doing it in the background while the machine is running // This will (obviously) make shutdown slower //Unattended-Upgrade::InstallOnShutdown "true"; // Send email to this address for problems or packages upgrades // If empty or unset then no email is sent, make sure that you // have a working mail setup on your system. A package that provides // 'mailx' must be installed. E.g. "[email protected]" Unattended-Upgrade::Mail "root"; // Set this value to "true" to get emails only on errors. Default // is to always send a mail if Unattended-Upgrade::Mail is set Unattended-Upgrade::MailOnlyOnError "true"; // Do automatic removal of new unused dependencies after the upgrade // (equivalent to apt-get autoremove) //Unattended-Upgrade::Remove-Unused-Dependencies "false"; // Automatically reboot *WITHOUT CONFIRMATION* if a // the file /var/run/reboot-required is found after the upgrade Unattended-Upgrade::Automatic-Reboot "true"; // Use apt bandwidth limit feature, this example limits the download // speed to 70kb/sec //Acquire::http::Dl-Limit "70"; As you can see Automatic-Reboot is true and thus the server should automaticly reboot. Last time I checked the server was online for over 100 days, which means that the update from Debian 7.1 to Debian 7.2 has happened while the server was up (and indeed, all updates were installed), but this involves kernel updates, which means that the server should reboot. It did not. The server was running very slow, so I rebooted which fixed that. I did some research and found out that unattended-upgrades responds to the reboot-required file in /var/run/. I touched this file and waited one week, the file still exists and the server did not reboot. So I think that unattended-uppgrades ignores the auto-reboot part. So, am I doing somthing wrong here? Why did the server not restart? The upgrade part works perfect by the way, its just the reboot part that does not seem to work as it should.

    Read the article

  • How to diagnose computer lockups and freezes?

    - by Scott Mitchell
    I built a desktop computer a couple years back with the following specs: CPU: Intel Core 2 Quad Q9300 Yorkfield 2.5GHz 6 MB L2 Cache LGA 775 95W Quad-Core Processor BX80580Q9300 Motherboard: EVGA 122-CK-NF68-T1 LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard Video Card: Two EVGA 256-P2-N758-TR GeForce 8600GT SCC 256 MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card PSU: SeaSonic S12 Energy Plus SS-550HT 550W ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS Certified Active PFC Power Supply Memory: Two G.SKILL 4 GB (2 x 2 GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model F2-6400CL5D-4GBPQ Since its inception, the machine has periodically locked up, the regularity having varied over the years from once a day to once a month. Typically, lockups happen once every few days. By "lockup" I mean my computer just freezes. The screen locks up, I can't move the mouse. Hitting keys on my keyboard that normally turn LEDs on or off on the keyboard (such as Caps Lock) no longer turn the LEDs on or off. If there was music playing at the time of the lockup, noise keeps coming out of the speakers, but it's just the current frequency/note that plays indefinitely. There is no BSOD. When such a lockup occurs I have to do a hard reboot by either turning off the computer or hitting the reset button. I have the most recent version of the NVIDIA hardware drivers, and update them semi-regularly, but that hasn't seemed to help. I am currently using Windows 7 x64, but was previously using Windows Server 2003 x64 and having the same lockup issues. My guess is that it's somehow video driver or motherboard related, but I don't know how to go about diagnosing this problem to narrow down which of the two is the culprit. Additional information re: cooling Regarding cooling... I've not installed any after-market cooling systems aside from two regular fans I scavenged from an older computer. The fan atop the CPU is the one that shipped with it. One of the two scavenged fans I added it located at the bottom tower of the corner, in an attempt to create some airflow from front to back. The second fan is pointed directly at the two video cards. SpeedFan installation and readings Per studiohack's suggestion, I installed SpeedFan, which provided the following temperature readings: GPU: 63C GPU: 65C System: 76C CPU: 64C AUX: 36C Core 0: 78C Core 1: 76C Core 2: 79C Core 3: 79C Update #3: Another Lockup :-( Well, I had another lockup last night. :-( SpeedFan reported the CPU temp at 38 C when it happened, and there was no spike in temperature leading up to the freeze. One thing I notice is that the freeze seems more likely to happen if I am watching a video. In fact, of the last 5 freezes over the past month, 4 of them have been while watching a video on Flickr. Not necessarily the same video, but a video nevertheless. I don't know if this is just coincidence or if it means anything. (As an aside, each night before bedtime my 2 year old daughter sits on my lap and watches some home videos on Flickr and, in the last month, has learned the phrase, "Uh oh, computer broke.") Update #4: MemTest86 and 3DMark06 Test Results: Per suggestions in the comments, I ran the MemTest86 overnight and it cycled through the 8 GB of memory 5 times without error. I also ran the 3DMark06 test without a problem (see my scores at http://3dmark.com/3dm06/15163549). So... what now? :-) Any further suggestions on what to check? Is there some way to get a stack trace or something when the computer locks like that? Resolution I have never did figure out the particular problems, but based on the suggestions here and elsewhere, I'm presuming it was a motherboard issue. In any event, I recently upgraded my system, buying a new motherbeard, PSU, CPU, and RAM, and that new rig has been working splendidly the past several weeks. I am using the same graphic cards as in the old setup, so I think it's safe to reason that they weren't the cause of the problem.

    Read the article

  • Possible to give one connection to each IP?

    - by Alice
    I am having overloading problems. Too many connections, and some IP has more than 20 connection at once. I do this command. netstat -anp |grep 'tcp\|udp' | awk '{print $5}' | cut -d: -f1 | sort | uniq -c | sort -n To get total of connection and this is the output: 1 106.3.98.81 1 106.3.98.82 1 108.171.251.2 1 110.85.103.207 1 111.161.30.217 1 113.53.103.55 1 119.235.237.20 1 124.106.19.34 1 157.55.32.166 1 157.55.33.49 1 157.55.34.28 1 175.141.103.239 1 180.76.5.59 1 180.76.5.61 1 188.235.165.216 1 205.213.195.70 1 216.157.222.25 1 218.93.205.100 1 222.77.209.105 1 27.153.148.109 1 27.159.194.242 1 27.159.253.71 1 54.242.122.201 1 61.172.50.99 1 65.55.24.239 1 71.179.78.5 1 74.125.136.27 1 74.125.182.30 1 74.125.182.36 1 79.112.225.39 1 93.190.139.208 2 124.227.191.67 2 157.55.33.84 2 157.55.35.34 2 190.66.3.107 2 203.87.153.38 2 220.161.119.3 2 221.6.15.156 2 27.153.148.116 2 27.159.197.0 2 96.47.224.42 3 202.14.70.1 3 218.6.15.42 3 222.77.218.226 3 222.77.224.187 3 37.59.66.100 3 46.4.181.244 3 87.98.254.192 3 91.207.8.62 4 188.143.233.222 4 218.108.168.166 4 221.12.154.18 4 93.182.157.8 4 94.142.128.183 5 180.246.170.187 5 8.21.6.226 6 178.137.94.87 6 218.93.205.112 7 199.15.234.222 9 9 125.253.97.6 10 178.137.17.196 11 46.118.192.179 12 212.79.14.14 21 72.201.187.135 27 0.0.0.0 Can anyone give me some directions, my server crashed few times this week because of this. Thanks. EDIT: Alright, my error logs says: [Thu Oct 18 12:17:39 2012] [error] could not make child process 4842 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4843 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4855 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4856 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4861 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4869 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4872 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4873 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4874 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4875 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4876 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4880 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4882 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4885 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4897 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4900 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4901 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4906 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4907 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4925 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4926 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4927 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4931 exit, attempting to continue anyway [Thu Oct 18 12:17:40 2012] [notice] caught SIGTERM, shutting down PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20060613+lfs/curl.iso' - /usr/lib/php5/20060613+lfs/curl.iso: cannot open shared object file: No such file or directory in Unknown on line 0 [Thu Oct 18 12:17:45 2012] [notice] Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny10 with Suhosin-Patch configured -- resuming normal operations And I have over thousands of line saying:(each has different process id) [Thu Oct 18 12:17:38 2012] [error] child process 4906 still did not exit, sending a SIGKILL And I also have line saying: [Wed Oct 17 09:44:58 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 50 MaxClients 300 MaxRequestsPerChild 5000 </IfModule>

    Read the article

  • stunnel crashing

    - by Jay
    I'm trying to use stunnel to secure a legacy application's communications. I can't seem to get it setup and working. Can anyone provide any hints where I'm going wrong? Here's what I'm trying to accomplish: A windows service on a client machine connects to a server on port 7000 using TCP. I'd like to encrypt the communication between client and server. Here's what I've tried: Created a new server that accepts ssl connections on port 7443. Got a certificate for the server and installed it. That seems to work with my test setup. Installed stunnel on my windows machine (version 7.43 from the distribution archive file). Installed libssl32.dll and libeay32.dll in the same directory as stunnel.exe ( from the openssl-0.9.8h-1 binary distribution). Installed it as a service using "stunnel -install" Configured stunnel as follows: debug=7 output=C:\p4\internal\Utility\Proxy\proxy.log service=Proxy taskbar=no [exchange] accept=7000 client=yes connect=proxy.blah.com:7443 I changed my hosts file to trick the old application into connecting through stunnel: server.blah.com 127.0.0.1 # when client looks up server it goes to stunnel proxy.blah.com IP-address-of-server.blah.com # stunnel connects to new server "server.blah.com" now resolves to the machine it's running on (i.e. stunnel). "proxy.blah.com" goes to the real server. stunnel should connect to the server. I start the stunnel service and try to connect. It looks like it's working but the stunnel service just shuts down with no message. 2010.04.19 13:16:21 LOG5[4924:3716]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:16:21 LOG5[4924:3716]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange accepted connection from 127.0.0.1:4134 2010.04.19 13:16:49 LOG6[4924:3748]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange connected remote server from x.253.120.19:4135 2010.04.19 13:20:24 LOG5[3668:3856]: Reading configuration from file stunnel.conf 2010.04.19 13:20:24 LOG7[3668:3856]: Snagged 64 random bytes from C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: Wrote 1024 new random bytes to C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: RAND_status claims sufficient entropy for the PRNG 2010.04.19 13:20:24 LOG7[3668:3856]: PRNG seeded successfully 2010.04.19 13:20:24 LOG7[3668:3856]: SSL context initialized for service exchange 2010.04.19 13:20:24 LOG5[3668:3856]: Configuration successful 2010.04.19 13:20:24 LOG5[3668:3856]: No limit detected for the number of clients 2010.04.19 13:20:24 LOG7[3668:3856]: FD=312 in non-blocking mode 2010.04.19 13:20:24 LOG7[3668:3856]: Option SO_REUSEADDR set on accept socket 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange bound to 0.0.0.0:7000 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange opened FD=312 2010.04.19 13:20:24 LOG5[3668:3856]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:20:24 LOG5[3668:3856]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:21:02 LOG7[3668:4556]: Service exchange accepted FD=372 from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:4556]: Creating a new thread 2010.04.19 13:21:02 LOG7[3668:4556]: New thread created 2010.04.19 13:21:02 LOG7[3668:3756]: Service exchange started 2010.04.19 13:21:02 LOG7[3668:3756]: FD=372 in non-blocking mode 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange accepted connection from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:3756]: FD=396 in non-blocking mode 2010.04.19 13:21:02 LOG6[3668:3756]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:21:02 LOG7[3668:3756]: connect_blocking: s_poll_wait x.80.60.32:7443: waiting 10 seconds 2010.04.19 13:21:02 LOG5[3668:3756]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange connected remote server from x.253.120.19:4157 2010.04.19 13:21:02 LOG7[3668:3756]: Remote FD=396 initialized 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): before/connect initialization 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server certificate A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server done A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client key exchange A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write change cipher spec A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write finished A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 flush data 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read finished A The client thinks the connection is closed: No connection could be made because the target machine actively refused it 127.0.0.1:7000 at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress) at System.Net.Sockets.Socket.Connect(EndPoint remoteEP) at Service.ConnUtility.Connect() Any suggestions?

    Read the article

  • Thoughts on home NAS server

    - by user826955
    I currently have a NAS with a 2x2TB HDD 1x16GB SSD layout on a mini-itx atom board. The NAS is in a Lian Li PC-Q07 case. On this system I was running freebsd 8 with a gmirror raid 1 setup, which was enough for my needs. So far I was using the NAS for: Fileserver with AFP protocol (only mac clients used) SVN server hosting all my source trees of my projects JIRA (performance was okay-ish) Timemachine backup for the macs The power consumption was about 38W, although I did not put HDDs asleep when unused (I think this is not possible in a raid setup). I liked the NAS because: the performance was good through gigabit LAN (enough for my needs) power consumption was good its a pretty small case and fits in one of my cupboards I disliked the NAS a bit because: it was a bit noisy, the Q07 case vibrated a good amount because of the HDDs. I switched the NAS off every evening I do not have a real backup of the data on the NAS, only the internal raid 1 as safety. I really dont want to loose my source trees under no circumstances, so I would really be sleeping better if I knew I had regular backups somewhere. Recently, the board seemed to have died, I can't boot anymore. Thus, I was thinking about a redesign of my NAS (I still have to find out what parts are broken, I probably need to replace the mainboard and SSD. HDDs seem to be okay). First of all, I was wondering what other users have as backup for their NAS? Are you actually using a second NAS, and regularly copying over the data to have it safe? Or is there any better solution to this? I was thinking about getting a cheap NAS like the synology DS112j with only one disk, and use rsync or something similar to regularly copy data over to the second NAS (wake the second NAS upon start, shut it down after copy). Although this approach seems somewhat weird, It would have the benefit (?) that I could use a single disk instead of raid in the main NAS, and put the disk asleep when idle, and have the NAS running 24/7 with low energy consumption (I found no way to do this with a gmirror setup). Is there any recommended backup solution for a small NAS? Then I was thinking about a different raid setup. Since I have to buy a new mainboard as well as SSD, I might as well switch over to a i3 board with more ram, and also switch to ZFS. I am not familar with ZFS, I've never used it, but I read and hear much about it. Would it be viable to set up a ZFS storage with only 2 disks? Can I easily extend this storage with more disks, once I choose to add some? I could maybe get a new case like the Fractal Design Array R2 which has more 3,5" slots. I could as well get another 2 disks, but I would prefer sticking with the existing 2 for enegery/heat/noise reasons. Should I go for a ZFS storage or stick to my gmirror setup? I would also like to keep freebsd as operating system, and also I dont need any web gui or something (that is, I dont need/want to use FreeNAS or Openfiler etc). Does anyone maybe have a sample setup in use so I can compare energy consumption/noise/software setup? Any guidance towards the NAS of my dreams (silent, low energy, safe w/ backups) much appreciated.

    Read the article

  • Parallel processing slower than sequential?

    - by zebediah49
    EDIT: For anyone who stumbles upon this in the future: Imagemagick uses a MP library. It's faster to use available cores if they're around, but if you have parallel jobs, it's unhelpful. Do one of the following: do your jobs serially (with Imagemagick in parallel mode) set MAGICK_THREAD_LIMIT=1 for your invocation of the imagemagick binary in question. By making Imagemagick use only one thread, it slows down by 20-30% in my test cases, but meant I could run one job per core without issues, for a significant net increase in performance. Original question: While converting some images using ImageMagick, I noticed a somewhat strange effect. Using xargs was significantly slower than a standard for loop. Since xargs limited to a single process should act like a for loop, I tested that, and found it to be about the same. Thus, we have this demonstration. Quad core (AMD Athalon X4, 2.6GHz) Working entirely on a tempfs (16g ram total; no swap) No other major loads Results: /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 1 convert -auto-level real 0m3.784s user 0m2.240s sys 0m0.230s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 2 convert -auto-level real 0m9.097s user 0m28.020s sys 0m0.910s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 10 convert -auto-level real 0m9.844s user 0m33.200s sys 0m1.270s Can anyone think of a reason why running two instances of this program takes more than twice as long in real time, and more than ten times as long in processor time to complete the same task? After that initial hit, more processes do not seem to have as significant of an effect. I thought it might have to do with disk seeking, so I did that test entirely in ram. Could it have something to do with how Convert works, and having more than one copy at once means it cannot use processor cache as efficiently or something? EDIT: When done with 1000x 769KB files, performance is as expected. Interesting. /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 1 convert -auto-level real 3m37.679s user 5m6.980s sys 0m6.340s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 1 convert -auto-level real 3m37.152s user 5m6.140s sys 0m6.530s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 2 convert -auto-level real 2m7.578s user 5m35.410s sys 0m6.050s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 4 convert -auto-level real 1m36.959s user 5m48.900s sys 0m6.350s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 10 convert -auto-level real 1m36.392s user 5m54.840s sys 0m5.650s

    Read the article

< Previous Page | 675 676 677 678 679 680 681 682 683 684 685 686  | Next Page >