Search Results

Search found 2702 results on 109 pages for 'dell xps'.

Page 68/109 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

  • Broadcom wireless card disappeards on restart

    - by Kristian Jones
    I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

    Read the article

  • Wired internet speed is slow in Ubuntu 12.04

    - by RameshKatkam
    I have dual boot Windows 7 and Ubuntu 12.04 on my Dell N4110 laptop. I recently installed Ubuntu 12.04 on my existing windows 7 hard drive. I am experiencing very slow internet speed on Ubuntu(wired connection). But on Windows,internet is really fast. I disabled ipv6 by editing /etc/sysctl.conf No avail. Then i run the following command. sudo ethtool -s eth0 speed 100 duplex full autoneg off No benefit. I am having "Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05)" network card.

    Read the article

  • Is there a simple, safe way to trigger a GPU lockup on a susceptible computer?

    - by Abe
    Answers to my previous question, Ubuntu 12.04 froze, requiring powercycle. What should I look / grep for in the logs?, have led me to suspect that my computer is experiencing an intermittent GPU lockup. It has been happening about once a week, usually when I am using Chrome. Today it happened when I was creating a diagram on lucidchart I have a Dell Optiplex 755 with an ATI Radeon HD 2400 XT and dual monitors running in Xinerama mode. I am using 12.04 with the proprietary ATI driver installed. When the computer locks-up, I can still ssh in. And I would like to follow the instructions on reporting this provided at https://wiki.ubuntu.com/X/Troubleshooting/Freeze Is there a (safe) way to cause a GPU lockup so that I can go ahead and file a bug, rather than waiting until it happens again?

    Read the article

  • How to install a Lexmark z600 series printer?

    - by Uri Herrera
    It has been a headache trying to install this printer. All the tutorials I found are for older versions of Ubuntu, and none of them work. How can I install this printer? Edit: HOWTO: Install PITA Lexmark Z600 Z615 and Dell Photo Printer 720 Setup Lexmark Z600 and X series printer on Ubuntu (i tried this one, only that it was translated to spanish, but it was the same instructions) HOWTO: Lexmark Printers I always get an error when extracting the converted tars with all of the tuts, invalid argument or the file doesn't exist. Looks like, i was missing some ia32 libs .. and that caused the errors with the tar files, anyways i still can't print now i get this, cups-insecure-filter How to install Lezmark Z600 series printer Here, the OP offers 2 debs, i installed them on a 32 bit Ubuntu install, now the printer gets recognized but still can't print, 'cause i'm missing a filter, "rastertoz600".

    Read the article

  • Unwanted authentication request window at login after upgrade to Ubuntu 13.10

    - by UBod
    I recently upgraded to Ubuntu 13.10 (64bit) on my Dell Laptop. Since then, at each login, a dialog window entitled "Authentication request ... Please enter the password for account "[email protected]"." appears (I would rather post a screenshot if I could, but I am not entitled to do that because I do not have the necessary 10 reputation credits). I neither have any idea why my password (I checked it a hundred times) does not work ("Password was incorrect") nor why this dialog is displayed at all. As said, I never saw it before 13.10. I looked around in different forums and it seems (please correct me if I am wrong) that it stems from evolution server. I also deleted ~/.config/evolution/ entirely - without any effect. Further note that I am not using evolution at all and I would rather like to get rid of it completely, but I do not dare to remove evolution-server. Any ideas? Thanks in advance, Ulrich

    Read the article

  • Cannot scale frequency of a Core i7 2720QM

    - by user51414
    I own a Dell Latitude E6520 with an Intel CPU (Core i7 2720QM). After installing cpufrequtils, I get the following message : cpufrequtils 007: cpufreq-info (C) Dominik Brodowski 2004-2009 Veuillez rapportez les erreurs et les bogues à [email protected], s'il vous plait. analyse du CPU 0 : **pas de pilotes cpufreq reconnu pour ce CPU** maximum transition latency: 4294.55 ms. In English : no cpufreq pilot found for this CPU. Thus my CPU runs always at full speed (2,2 GHz) which consume the battery and shorten its life. I don't either know how to activate turbo mode. Please help ! Regards, Al

    Read the article

  • This Week in Geek History: The Call of Cthulhu, the Columbia Shuttle Disaster, and the Birth of Facebook

    - by Jason Fitzpatrick
    This week in Geek History saw the beginning of the Cthulhu horror mythos, the Columbia space shuttle disaster, and the birth of Facebook. Also, check out our new addition “Other Notable Moments” at the end for more facts and trivia from this week in Geek History. Latest Features How-To Geek ETC How to Integrate Dropbox with Pages, Keynote, and Numbers on iPad RGB? CMYK? Alpha? What Are Image Channels and What Do They Mean? How to Recover that Photo, Picture or File You Deleted Accidentally How To Colorize Black and White Vintage Photographs in Photoshop How To Get SSH Command-Line Access to Windows 7 Using Cygwin The How-To Geek Video Guide to Using Windows 7 Speech Recognition Stylebot Customizes Web Pages in Chrome, Now Has Downloadable Styles Blackberry, Dell, Apple, and Motorola Tablets Compared [Infographic] Encrypt Your Google Search Queries Vintage Posters Showcase the History of Tech Advertising Google Cloud Print Extension Lets You Print Doc/PDF/Txt Files from Web Sites Hack a $10 Flashlight into an Ultra-bright Premium One

    Read the article

  • CodePlex Daily Summary for Sunday, January 30, 2011

    CodePlex Daily Summary for Sunday, January 30, 2011Popular ReleasesWPF Application Framework (WAF): WPF Application Framework (WAF) 2.0.0.3: Version: 2.0.0.3 (Milestone 3): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Remark The sample applications are using Microsoft’s IoC container MEF. However, the WPF Application Framework (WAF) doesn’t force you to use the same IoC container in your application. You can use ...Rawr: Rawr 4.0.17 Beta: Rawr is now web-based. The link to use Rawr4 is: http://elitistjerks.com/rawr.phpThis is the Cataclysm Beta Release. More details can be found at the following link http://rawr.codeplex.com/Thread/View.aspx?ThreadId=237262 and on the Version Notes page: http://rawr.codeplex.com/wikipage?title=VersionNotes As of the 4.0.16 release, you can now also begin using the new Downloadable WPF version of Rawr!This is a pre-alpha release of the WPF version, there are likely to be a lot of issues. If you...VivoSocial: VivoSocial 7.4.2: Version 7.4.2 of VivoSocial has been released. If you experienced any issues with the previous version, please update your modules to the 7.4.2 release and see if they persist. If you have any questions about this release, please post them in our Support forums. If you are experiencing a bug or would like to request a new feature, please submit it to our issue tracker. Web Controls * Updated Business Objects and added a new SQL Data Provider File. Groups * Fixed a security issue whe...PHP Manager for IIS: PHP Manager 1.1.1 for IIS 7: This is a minor release of PHP Manager for IIS 7. It contains all the functionality available in 56962 plus several bug fixes (see change list for more details). Also, this release includes Russian language support. SHA1 codes for the downloads are: PHPManagerForIIS-1.1.0-x86.msi - 6570B4A8AC8B5B776171C2BA0572C190F0900DE2 PHPManagerForIIS-1.1.0-x64.msi - 12EDE004EFEE57282EF11A8BAD1DC1ADFD66A654VFPX: VFP2C32 2.0.0.8 Release Candidate: This release includes several bugfixes, new functions and finally a CHM help file for the complete library.EnhSim: EnhSim 2.3.3 ALPHA: 2.3.3 ALPHAThis release supports WoW patch 4.06 at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - Added back in a p...DB>doc for Microsoft SQL Server: 1.0.0.0: Initial release Supported output HTML WikiPlex markup Raw XML Supported objects Tables Primary Keys Foreign Keys ViewsmojoPortal: 2.3.6.1: see release notes on mojoportal.com http://www.mojoportal.com/mojoportal-2361-released.aspx Note that we have separate deployment packages for .NET 3.5 and .NET 4.0 The deployment package downloads on this page are pre-compiled and ready for production deployment, they contain no C# source code. To download the source code see the Source Code Tab I recommend getting the latest source code using TortoiseHG, you can get the source code corresponding to this release here.Office Web.UI: Alpha preview: This is the first alpha release. Very exciting moment... This download is just the demo application : "Contoso backoffice Web App". No source included for the moment, just the app, for testing purposes and for feedbacks !! This package includes a set of official MS Office icons (143 png 16x16 and 132 png 32x32) to really make a great app ! Please rate and give feedback ThanksParallel Programming with Microsoft Visual C++: Drop 6 - Chapters 4 and 5: This is Drop 6. It includes: Drafts of the Preface, Introduction, Chapters 2-7, Appendix B & C and the glossary Sample code for chapters 2-7 and Appendix A & B. The new material we'd like feedback on is: Chapter 4 - Parallel Aggregation Chapter 5 - Futures The source code requires Visual Studio 2010 in order to run. There is a known bug in the A-Dash sample when the user attempts to cancel a parallel calculation. We are working to fix this.Catel - WPF and Silverlight MVVM library: 1.1: (+) Styles can now be changed dynamically, see Examples application for a how-to (+) ViewModelBase class now have a constructor that allows services injection (+) ViewModelBase services can now be configured by IoC (via Microsoft.Unity) (+) All ViewModelBase services now have a unit test implementation (+) Added IProcessService to run processes from a viewmodel with directly using the process class (which makes it easier to unit test view models) (*) If the HasErrors property of DataObjec...NodeXL: Network Overview, Discovery and Exploration for Excel: NodeXL Excel Template, version 1.0.1.160: The NodeXL Excel template displays a network graph using edge and vertex lists stored in an Excel 2007 or Excel 2010 workbook. What's NewThis release improves NodeXL's Twitter and Pajek features. See the Complete NodeXL Release History for details. Installation StepsFollow these steps to install and use the template: Download the Zip file. Unzip it into any folder. Use WinZip or a similar program, or just right-click the Zip file in Windows Explorer and select "Extract All." Close Ex...Kooboo CMS: Kooboo CMS 3.0 CTP: Files in this downloadkooboo_CMS.zip: The kooboo application files Content_DBProvider.zip: Additional content database implementation of MSSQL, RavenDB and SQLCE. Default is XML based database. To use them, copy the related dlls into web root bin folder and remove old content provider dlls. Content provider has the name like "Kooboo.CMS.Content.Persistence.SQLServer.dll" View_Engines.zip: Supports of Razor, webform and NVelocity view engine. Copy the dlls into web root bin folder to enable...UOB & ME: UOB ME 2.6: UOB ME 2.6????: ???? V1.0: ???? V1.0 ??Password Generator: 2.2: Parallel password generation Password strength calculation ( Same method used by Microsoft here : https://www.microsoft.com/protect/fraud/passwords/checker.aspx ) Minor code refactoringVisual Studio 2010 Architecture Tooling Guidance: Spanish - Architecture Guidance: Francisco Fagas http://geeks.ms/blogs/ffagas, Microsoft Most Valuable Professional (MVP), localized the Visual Studio 2010 Quick Reference Guidance for the Spanish communities, based on http://vsarchitectureguide.codeplex.com/releases/view/47828. Release Notes The guidance is available in a xps-only (default) or complete package. The complete package contains the files in xps, pdf and Office 2007 formats. 2011-01-24 Publish version 1.0 of the Spanish localized bits.ASP.NET MVC Project Awesome, jQuery Ajax helpers (controls): 1.6.2: A rich set of helpers (controls) that you can use to build highly responsive and interactive Ajax-enabled Web applications. These helpers include Autocomplete, AjaxDropdown, Lookup, Confirm Dialog, Popup Form, Popup and Pager the html generation has been optimized, the html page size is much smaller nowFacebook Graph Toolkit: Facebook Graph Toolkit 0.6: new Facebook Graph objects: Application, Page, Post, Comment Improved Intellisense documentation new Graph Api connections: albums, photos, posts, feed, home, friends JSON Toolkit upgraded to version 0.9 (beta release) with bug fixes and new features bug fixed: error when handling empty JSON arrays bug fixed: error when handling JSON array with square or large brackets in the message bug fixed: error when handling JSON obejcts with double quotation in the message bug fixed: erro...Microsoft All-In-One Code Framework: Visual Studio 2008 Code Samples 2011-01-23: Code samples for Visual Studio 2008New ProjectsAnaida - WebSocket Client/Adapter: Anaida is a WebSocket Client Library/Adapter. With 3 versions for Java, Silverlight and C#CutPasteAssign: Visual Studio extension to assist in the common refactoring of assigning parameters to local variables.Drori Photos: Photos of Drori the photographerD-Solution: App de D-SolutionEnigma Home Inventory: Most consumers do not have an itemized list of proof of ownership. Enigma Home Inventory may take the hassle out of arguing with the insurance companies. This project is aimed to be for a simple inventory program for end users who are not computer savvy.FastKnow: is a CMS & wikiFileSignatures: FileSignatures aims to create a class library that can identify the file format based on file contents. The project is written in C# 3.0, and can be used in .NET 3.5 and 4.0 projects.Genrsis: The aim of the Genrsis project is to be a suite of products that you can use to build things, starting with a workflow-based project management tool. Built in C#, it should be a one-stop place to get well-integrated products to get you up and running.MVC Demos: MVC 2 and MVC 3 examples with ajax and json.MVC Templates for DevExpress: Scaffolding templates for use in ASP.NET MVC 2 with DevExpress MVC Extensions for ASP.NET MVCPixel Replacer: The Pixel Replacer is a simple library for replacing pixel colors with a new color, by setting a filter rule.ReviewPal - The Code Review Companion for .Net.: ReviewPal, the Code Review Companion for .Net. This is an Add-In / Extension for Visual Studio 2008 & Visual Studio 2010. The aim of the Add-In / Extension is to do a source code review within the Visual Studio IDE where code makes more sense and most readable.SMVector3: Vector3 class implemented as float array or with SIMD instructions with the same interface so it is transparant whether you decide to use one version or another. You can also chance version during the life cycle of the projects.uRibbon - Office 2007 Ribbon control for VB.NET: Office 2007 ribbon control, with Orb and graphic transitions. After searching for many day looking for an Office 2007-like ribbon bar, I finally gave up and decided to write my own. It's in decent shape as-is. But anyone interested in helping me to continue the devlopment??vtcheck: This will read a target binary and check to see if it is detected by VirusTotal.Web Scheduled Task Framework: A simple set of classes intended to allow the standalone scheduling of tasks (arbitrary code to execute) on a .net website without requiring access to the operating system.WP7 codeproject app: A Windows Phone 7 app for browsing codeproject.com.zhongjh: ?????????,???????。???????????: ???????????

    Read the article

  • Ubuntu freezes/crash after wake when upgraded to 13.10

    - by krustbr
    Back on 13.04 it didn't occurred. I've upgraded to 13.10, systems apparently working fine, but, when I put it to sleep(using or not using extended monitor) and try to wake up, I see the screen(both), without lock-screen, but completely freeze, Neither tty open, nor the keyboard works. So, only option remains is to force shut-down. Any clue how to investigate the cause or fix it? Thanks in advance, any info that'll help you could ask! Ubuntu 13.10 x64 - not a fresh install/upgraded - with Unity Dell Vostro 3550 AMD Proprietary Drivers - 13.11 / Hybrid with Intel

    Read the article

  • How can I upgrade to Lubuntu 14.04.1 withot a PAE kernel?

    - by Richard
    On my Dell Latitude D800 laptop, which has an old Pentium M without PAE support, I was able to successfully install Lubuntu 14.04 from the CD. When I try to upgrade, I get the error: PAE not enabled Your system uses a CPU that does not have PAE enabled. Ubuntu only supports non-PAE systems up to Ubuntu 12.04. To upgrade to a later version of Ubuntu, you must enable PAE (if this is possible) see: http://help.ubuntu.com/community/EnablingPAE I have seen the Communit Wiki page for PAE. The suggestion is to add forcepae to the command line options. When I do this, I get the same message. Moreover, dmesg does not indicate PAE was ever enabled. Is there anything else I can ry to get Lubuntu to upgrade correctly?

    Read the article

  • How do I rotate my monitor using xorg?

    - by user1106405
    I have just installed KUbuntu 12.10, and I am attempting to rotate my monitor 90 deg to the left. When I add the option to rotate, the monitor seems to ignore the directive. I'm currently using dual 02:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) 03:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) and NVidia driver version 310 My xorg.conf is as follows: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 304.51 (buildd@komainu) Fri Oct 12 12:53:49 UTC 2012 # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 310.14 ([email protected]) Tue Oct 9 13:04:01 PDT 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 1280 0 Screen 1 "Screen1" RightOf "Screen0" Screen 2 "Screen2" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "1" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Samsung SyncMaster" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 60.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 1908WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 EndSection Section "Monitor" Identifier "Monitor2" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 0 EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 1 EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select @1920x1080 +0+0; DFP-0: nvidia-auto-select @1920x720 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-2: nvidia-auto-select +0+0" Option "Rotate" "left" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Enable" EndSection Edit: If I delete the xorg.conf and reboot, I am able to rotate my monitor, however, my third monitor is not recognized: Screen 0: minimum 8 x 8, current 3360 x 1200, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 disconnected (normal left inverted right x axis y axis) DVI-I-2 connected 1920x1200+0+0 (normal left inverted right x axis y axis) 518mm x 324mm 1920x1200 60.0*+ 1600x1200 60.0 1280x1024 60.0 1280x960 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 HDMI-0 disconnected (normal left inverted right x axis y axis) DVI-I-3 connected 1440x900+1920+0 (normal left inverted right x axis y axis) 408mm x 255mm 1440x900 59.9*+ 75.0 1280x1024 75.0 60.0 1280x800 59.8 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 640x480 75.0 72.8 59.9

    Read the article

  • Wifi won't work without ethernet (Ubuntu 12.04)

    - by alok
    I have a strange problem. I am running Ubuntu 12.04 on a Dell Studio 1558 laptop. I'm usually unable to access Wifi (I have a BCM43224 wireless card with the STA proprietary driver installed.) So I have to unplug the ethernet cable from my Wifi router and stick it into my laptop's ethernet port to access the Internet. But when I stick the cable back into the Wifi router and try connecting to Wifi, Wifi inexplicably starts working. How can I get Wifi to work all the time without having to 'jumpstart' it with an ethernet connection?

    Read the article

  • GRUB- error: no such partition grub rescue and Error: No default or UI configuration directive found boot > on pendrive

    - by Ash
    I have dell inspiron, previously I installed Ubuntu 11.10 on my Windows 7 and made it dual boot. But since I want to upgrade my Ubuntu version and change the partition spacing, I deleted 11.10 partition directly and extended my hardrive space (Windows + Ubuntu) at that moment everything was fine. Then I prepared a 12.04 32bit USB and installed it . It was installed but isn't showing dual boot option like 11.10 and my machine directly boot into Windows 7. So instantly i again deleted my 12.04 partition . Now I login into Windows 7 but whenever I put USB ( with 12.04 ) to boot from it, I am facing error of "no such partition grub rescue" even though I try to put lower version(11.04) it showing another error "Error: No default or UI configuration directive found boot " I have reinstall Windows 7 and reformat all partition, still I am facing same error :(

    Read the article

  • How can I get nvidia-settings to work?

    - by Palace Chan
    I have an ASUS N56VM-TB71 with a GeForce 630M graphics card. I have ubuntu 12.04 and when I vga plugged in a dell monitor, i am able to use it. When I then use my laptops hdmi port to plug in my second monitor, nothing happens, so I went to nvidia-settings and I got the error: You do not appear to be using the NVIDIA X Driver, please run nvidia-xconfig as root and restart the X server. I ran this command and rebooted but I still cannot access nvidia-settings and I keep getting that error even though my /etc/X11/xconf.org is the one that got generated by running that command! What can I do to get around that and use my second monitor as well?

    Read the article

  • How to install XAMPP?

    - by Rani.Shemer
    Hi all im a noob on Ubuntu/Linux World, So i need some that give a full tutorial to How to install Xampp from apachefriends.org correctly on Ubuntu 11.10 + all beyond Ubuntu for 32 bit and also 64 bit Desktop Version.. and also i need this: Make a Folder on Your Home Folder and Linked to htdocs from Apache Web Server Make a GUI interface for Xmapp Start Xampp when Ubuntu Boot Up or Start Ubuntu (Note: i ask it for both X86 and X64 so people in the further can see the tutorials) New Data: What i did was i download from apachefriends.org for now and i also what to say that I'm currently running Ubuntu 11.10 X64 bit for Dell Studio 1558 processor intel i3 i will let you know guys which solution was the best, and it is for a Desktop Version of Ubuntu 11.10 (Laptop 15 inch screen ^_^ ) not Server Ubuntu

    Read the article

  • Choppy/unresponsive keyboard and mouse pointer until suspend

    - by Stefan Thyberg
    I had a problem where my mouse and keyboard would be choppy. The mouse pointer would work at "1-2 fps" and the keyboard would keep missing letters as i was typing them. Since both are USB-Devices, i suspected a problem there immediately, so whenever i got this problem, i would suspend the computer and start it again, for the problem to be gone. The problem started appearing when I plugged the mouse and keyboard directly into the computer rather than the USB-Hub in the screen. I'm using a Logitech UltraX Flat and a Razer Lachesis, on a Dell Latitude E6510.

    Read the article

  • Horible lag on Xubuntu media center setup

    - by William
    I am setting up a media center running Xubuntu 11.10 as a media center. It is using the XFCE desktop enviroment. I have the NVIDIA drivers installed from the Additional Drivers program, and uninstalled all but the esennitial software. The computer is a Dell Dimension 3000. You can view detailed technical specifications here. The graphics card installed is a Geforce 8400 GS. I have installed all updates through Update Manager. What can I do to fix the horrible lag? It makes watching TV impossible.I have uploaded two videos of the lag, here and here. The second one does not have sound because the sound stops playing on some channels that lag a lot. The TV card is a Hauppage 950q USB, and the TV recording program is Kaffiene. Please help me with this, I am trying to do this to show how great Ubuntu is to the rest of the family.

    Read the article

  • Expand size of Edubuntu partition on dual boot PC

    - by trptplyr
    I wasn't allowed to update to the next release of Edubuntu recently. It gave me an error stating that I did not have enough space to run the update. How can I expand the size of the Edubuntu partition to allow me to update? I am new to Linux so I hope that I am giving you enough and correct information on my system. I am using an older Dell Inspiron 9400 laptop. My root.disk file is 16.3Gb and the system.disk file is 256Mb. I would appreciate someone to point me to documentation or give me instructions on how to do this. Thank you.

    Read the article

  • Can't activate "mirror display"

    - by Nemo Peeters
    I have Ubuntu 12.04 on a Dell latitude E6410, I have a problem when using the VGA output I always have dual monitor and can't switch on the "mirror display" toggle under systems setting/displays. It's rather annoying when having to do presentation with a video projector. the option "mirror display" is in light grey and I can"t tick the box. Thanks for those who might have an idea how to resolve this? update: driver is: Intel® Ironlake Mobile x86/MMX/SSE2 card something like this ? description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 64 bits clock: 33MHz

    Read the article

  • Laptop resumes from suspend while lid is closed

    - by Gus
    I have a Dell Studio 15 and I am running Ubuntu 10.10. When I close my lid or select the suspend option, the machine suspends as indicated by the slowly pulsing power indicator. I'll put the machine in my bag and after a while it seems that the machine resumes, at least I think. When ever I go to get it, it's overheated and the system cannot resume. I am guessing that the processor resets in this overheat condition, but heat is still generated. This has happened about three times and I'm getting worried that I'll end up damaging the machine. How can I diagnose why the system is resuming from suspend? Can I force it to never resume from suspend if the lid is down?

    Read the article

  • Unity poor performance after upgrading to 13.10

    - by Juzer Ali
    I upgraded recently from 13.04 to 13.10. I have Dell Inspiron 4GB RAM, Intel Core i3. Login takes a lot of time and all the graphics are very slow. Alt + Tab takes a lot of time (seconds). After reading some threads, I also removed Cinnamon desktop, but it didn't change anything. I had to ultimately fall back to Gnome Flashback (no effects). Gnome flashback works fine without any issues. Can anyone please help me get back to Unity, else I will have a very hard time running using Gnome.

    Read the article

  • Probelm with ATI catalyst drivers in ubuntu 13.10

    - by Raja
    Recently I've installed dual boot ubuntu 13.10 alongside windows 8. My Laptop is Dell Inspiron 15, with AMD Radeon HD 7670 Video Card. Without fglrx my battery is draining to 1:30 hrs from 3:30hrs (In Ubuntu 13.04 but very slow booting ) so I installed fglrx using What is the correct way to install ATI Catalyst Video Drivers (fglrx)? But the problem is as you all know, Black Screen after logging into ubuntu. Tried so many solutions for this like reinstalling unity , ubuntu-desktop , compizconfig , etc.. but none helped except removing fglrx* completely. (But I need them very badly due to battery) Assuming that all hope is lost., Posting here as a final try.! Will be highly greatfull for those who helped :) PS : For those who think this question is a duplicate., Though the question may be a duplicate, but the answer is not! (so give me a assured solution for this problem before flagging this as duplicate., Kindly understand my frustation) Thank You !

    Read the article

  • No lock screen when the right click menu is open

    - by Shivram
    I just found that the lock screen on my laptop does not show up when the right click menu is open. I discovered this when I pressed the right click button accidentally while closing the lid and the laptop went to sleep, but the lock screen never showed up when I opened the lid again. I am also not able to lock the system manually(with ctrl+alt+L) when the right click menu is open. Is this by design or is it a bug? I would assume that the screen should be locked automatically when the computer goes to sleep, but this doesn't seem to be the case. Anyone have any suggestions? My specs are: Dell Vostro 1500, Ubuntu 12.10

    Read the article

  • Logitech M515 does not work after upgrade to 12.04

    - by user877329
    After upgrading to 12.04, my Logitech M515 does not work here is some output from the terminal: lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0411:002a BUFFALO INC. (formerly MelCo., Inc.) Bus 001 Device 004: ID 055d:3021 Samsung Electro-Mechanics Co. Bus 002 Device 002: ID 413c:2005 Dell Computer Corp. RT7D50 Keyboard Bus 004 Device 002: ID 0582:0074 Roland Corp. EDIROL UA-25 Bus 005 Device 002: ID 046d:c52b Logitech, Inc. Unifying Receiver dmesg | grep Logitech [ 30.470528] logitech-djreceiver 0003:046D:C52B.0004: hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.3-2/input2 The cursor does not move. Also the mouse was working in 11.10 and is working in Windows NT 5.1.2600.

    Read the article

  • Cisco Linksys AE2500 wireless adapter not working

    - by makuto
    I have a Cisco AE2500 I've used with my laptop to get internet. I had to install the drivers by following this forum: http://ubuntuforums.org/showthread.php?t=1805830 But now the blue light on the adapter doesn't turn on at all, but ndiswrapper reports it is connected. I have no connection to the internet on my laptop, and the adapter doesn't show it's blue light on any of the USB ports of my computer or on the 4 port hub I have. Is there some way I can reset something so that the blue light will show again? I'm using Ubuntu 11.10 on a Dell Latitude D505 laptop. EDIT: I deleted and reinstalled the same exact driver and everything worked again.

    Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >