Search Results

Search found 18961 results on 759 pages for 'tp link'.

Page 682/759 | < Previous Page | 678 679 680 681 682 683 684 685 686 687 688 689  | Next Page >

• Determining Maximum Txpower a WiFi Card Supports?

  - by BigGenius

  I have a Atheros R9285 wifi card. How can i determine , what is max. Txpower it can support? biggenius@hackbook:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Default" Mode:Managed Frequency:2.437 GHz Access Point: 00:08:5C:9D:4F:40 Bit Rate=2 Mb/s Tx-Power=35 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=24/70 Signal level=-86 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:140 Invalid misc:247 Missed beacon:0 eth0 no wireless extensions. biggenius@hackbook:~$ iw phy0 info Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (35.0 dBm) * 2417 MHz [2] (35.0 dBm) * 2422 MHz [3] (35.0 dBm) * 2427 MHz [4] (35.0 dBm) * 2432 MHz [5] (35.0 dBm) * 2437 MHz [6] (35.0 dBm) * 2442 MHz [7] (35.0 dBm) * 2447 MHz [8] (35.0 dBm) * 2452 MHz [9] (35.0 dBm) * 2457 MHz [10] (35.0 dBm) * 2462 MHz [11] (35.0 dBm) * 2467 MHz [12] (35.0 dBm) * 2472 MHz [13] (35.0 dBm) * 2484 MHz [14] (35.0 dBm) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 5180 MHz [36] (35.0 dBm) * 5200 MHz [40] (35.0 dBm) * 5220 MHz [44] (35.0 dBm) * 5240 MHz [48] (35.0 dBm) * 5260 MHz [52] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (35.0 dBm) * 5765 MHz [153] (35.0 dBm) * 5785 MHz [157] (35.0 dBm) * 5805 MHz [161] (35.0 dBm) * 5825 MHz [165] (35.0 dBm) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO } <= 8, total <= 2048, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (82) * Unknown command (81) * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS.

  Read the article

• How to Watch NCAA March Madness Online

  - by DigitalGeekery

  You’ve filled out your brackets and now you are ready for one of America’s most popular sporting events. But what if you are you stuck at work or away from your TV?  Or your local affiliate is showing a different game? Today we show how to catch all the March Madness online. March Madness on Demand You’ll need a broadband connection, 512 MB RAM or higher, with cookies and Javascript enabled in your browser. March Madness on Demand offers two viewing options, a Standard Player and a High Quality player. The High Quality player is not, unfortunately, high definition. Standard Player Requirements Windows XP/Vista/7 or Mac OS X IE 6+ (We also successfully tested it in Firefox, Chrome, & Opera) Adobe Flash Player 9 or higher High Quality Player Requirements 2.4 GHz Pentium 4 or Intel-based Macintosh Mac OS 10.4.8+ (Intel-based) Windows: XP SP2, Vista, Server 2003, Server 2008, Windows 7 Firefox 1.5+ or IE 6/7/8 Silverlight 3 browser plug-in Watching March Madness on Demand Go to the March Madness on Demand website. (Link below) Check the “Watch in High Quality” section to see if your browser is ready and compatible for the High Quality viewer. If not, you’ll see a message indicating either your browser and system are incompatible… Or that you need to install Silverlight. To install Silverlight, click on the “Get HQ” button and follow the prompts to download and install Silverlight. To launch the player, click the large red “Launch Player” button. At the top of the screen, you’ll see the current and upcoming games. Click on “Watch Now” below to begin watching. At the bottom left, is where you click to watch with the High Quality player. If to many people are watching the High Quality player, you’ll see the following message and have to go back to the Standard Player. At the lower right are volume controls, a “Full Screen” button, and a “Share” button which allows you to share the game you are watching on various social networking sites like Facebook and Twitter. Perhaps most importantly for those who want to steal a bit of viewing time while at work is the “Boss Button” at the top right. Clicking on the “Boss Button” will open a fake Office document so it may appear at first glance like you’re actually doing legitimate work. To return to the game, click anywhere on the screen with your mouse. You’ll be able to catch every single game of the tournament from the first round all the way through the championship with March Madness on Demand. If your computer and Internet connection can handle it, you can even watch multiple games at the same time by opening March Madness on Demand in multiple browser windows. Watch March Madness online Similar Articles Productive Geek Tips Weekend Fun: Watch Television on Your PC with AnyTVWatch NFL Sunday Night Football On Your PCWatch TV On Your PC with FreeZ Online TVGeek Fun: Download Favorite NBC Programs for FreeDitch the RealPlayer Bloat with Real Alternative TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional How to Browse Privately in Firefox Kill Processes Quickly with Process Assassin Need to Come Up with a Good Name? Try Wordoid StockFox puts a Lightweight Stock Ticker in your Statusbar Explore Google Public Data Visually The Ultimate Excel Cheatsheet

  Read the article

• Bind a Wijmo Grid to Salesforce.com Through the Salesforce OData Connector

  - by dataintegration

  This article will explain how to connect to any RSSBus OData Connector with Wijmo's data grid using JSONP. While the example will use the Salesforce Connector, the same process can be followed for any of the RSSBus OData Connectors. Step 1: Download and install both the Salesforce Connector from RSSBus and the Wijmo javascript library. Step 2: Next you will want to configure the Salesforce Connector to connect with your Salesforce account. If you browse to the Help tab in the Salesforce Connector application, there is a link to the Getting Started Guide which will walk you through setting up the Salesforce Connector. Step 3: Once you have successfully configured the Salesforce Connector application, you will want to open a Wijmo sample grid file to edit. This example will use the overview.html grid found in the Samples folder. Step 4: First, we will wrap the jQuery document ready function in a callback function for the JSONP service. In this example, we will wrap this in function called fnCallback which will take a single object args. <script id="scriptInit" type="text/javascript"> function fnCallback(args) { $(document).ready(function () { $("#demo").wijgrid({ ... }); }); }; </script> Step 5: Next, we need to format the columns object in a format that Wijmo's data grid expects. This is done by adding the headerText: element for each column. <script id="scriptInit" type="text/javascript"> function fnCallback(args) { var columns = []; for (var i = 0; i < args.columnnames.length; i++){ var col = { headerText: args.columnnames[i]}; columns.push(col); } $(document).ready(function () { $("#demo").wijgrid({ ... }); }); }; </script> Step 6: Now the wijgrid parameters are ready to be set. In this example, we will set the data input parameter to the args.data object and the columns input parameter to our newly created columns object. The resulting javascript function should look like this: <script id="scriptInit" type="text/javascript"> function fnCallback(args) { var columns = []; for (var i = 0; i < args.columnnames.length; i++){ var col = { headerText: args.columnnames[i]}; columns.push(col); } $(document).ready(function () { $("#demo").wijgrid({ allowSorting: true, allowPaging: true, pageSize: 10, data: args.data, columns: columns }); }); }; </script> Step 7: Finally, we need to add the JSONP reference to our Salesforce Connector's data table. You can find this by clicking on the Settings tab of the Salesforce Connector. Once you have found the JSONP URL, you will need to supply a valid table name that you want to connect with Wijmo. In this example, we will connect to the Lead table. You will also need to add authentication options in this step. In the example we will append the authtoken of the user who has access to the Salesforce Connector using the @authtoken query string parameter. IMPORTANT: This is not secure and will expose the authtoken of the user whose authtoken you supply in this step. There are other ways to secure the user's authtoken, but this example uses a query string parameter for simplicity. <script src="http://localhost:8181/sfconnector/data/conn/Lead.rsd?@jsonp=fnCallback&sql:query=SELECT%20*%20FROM%20Lead&@authtoken=<myAuthToken>" type="text/javascript"></script> Step 8: Now, we are done. If you point your browser to the URL of the sample, you should see your Salesforce.com leads in a Wijmo data grid.

  Read the article

• Building a project in VS that depends on a static and dynamic library

  - by fg nu

  Noob noobin'. I would appreciate some very careful handholding in setting up an example in Visual Studio 2010 Professional where I am trying to build a project which links: a previously built static library, for which the VS project folder is "C:\libjohnpaul\" a previously built dynamic library, for which the VS project folder is "C:\libgeorgeringo\" These are listed as Recipes 1.11, 1.12 and 1.13 in the C++ Cookbook. The project fails to compile for me with unresolved dependencies (see details below), and I can't figure out why. Project 1: Static Library The following are the header and source files that were compiled in this project. I was able to compile this project fine in VS2010, to the named standard library "libjohnpaul.lib" which lives in the folder ("C:/libjohnpaul/Release/"). // libjohnpaul/john.hpp #ifndef JOHN_HPP_INCLUDED #define JOHN_HPP_INCLUDED void john( ); // Prints "John, " #endif // JOHN_HPP_INCLUDED // libjohnpaul/john.cpp #include <iostream> #include "john.hpp" void john( ) { std::cout << "John, "; } // libjohnpaul/paul.hpp #ifndef PAUL_HPP_INCLUDED #define PAUL_HPP_INCLUDED void paul( ); // Prints " Paul, " #endif // PAUL_HPP_INCLUDED // libjohnpaul/paul.cpp #include <iostream> #include "paul.hpp" void paul( ) { std::cout << "Paul, "; } // libjohnpaul/johnpaul.hpp #ifndef JOHNPAUL_HPP_INCLUDED #define JOHNPAUL_HPP_INCLUDED void johnpaul( ); // Prints "John, Paul, " #endif // JOHNPAUL_HPP_INCLUDED // libjohnpaul/johnpaul.cpp #include "john.hpp" #include "paul.hpp" #include "johnpaul.hpp" void johnpaul( ) { john( ); paul( ); Project 2: Dynamic Library Here are the header and source files for the second project, which also compiled fine with VS2010, and the "libgeorgeringo.dll" file lives in the directory "C:\libgeorgeringo\Debug". // libgeorgeringo/george.hpp #ifndef GEORGE_HPP_INCLUDED #define GEORGE_HPP_INCLUDED void george( ); // Prints "George, " #endif // GEORGE_HPP_INCLUDED // libgeorgeringo/george.cpp #include <iostream> #include "george.hpp" void george( ) { std::cout << "George, "; } // libgeorgeringo/ringo.hpp #ifndef RINGO_HPP_INCLUDED #define RINGO_HPP_INCLUDED void ringo( ); // Prints "and Ringo\n" #endif // RINGO_HPP_INCLUDED // libgeorgeringo/ringo.cpp #include <iostream> #include "ringo.hpp" void ringo( ) { std::cout << "and Ringo\n"; } // libgeorgeringo/georgeringo.hpp #ifndef GEORGERINGO_HPP_INCLUDED #define GEORGERINGO_HPP_INCLUDED // define GEORGERINGO_DLL when building libgerogreringo.dll # if defined(_WIN32) && !defined(__GNUC__) # ifdef GEORGERINGO_DLL # define GEORGERINGO_DECL _ _declspec(dllexport) # else # define GEORGERINGO_DECL _ _declspec(dllimport) # endif # endif // WIN32 #ifndef GEORGERINGO_DECL # define GEORGERINGO_DECL #endif // Prints "George, and Ringo\n" #ifdef __MWERKS__ # pragma export on #endif GEORGERINGO_DECL void georgeringo( ); #ifdef __MWERKS__ # pragma export off #endif #endif // GEORGERINGO_HPP_INCLUDED // libgeorgeringo/ georgeringo.cpp #include "george.hpp" #include "ringo.hpp" #include "georgeringo.hpp" void georgeringo( ) { george( ); ringo( ); } Project 3: Executable that depends on the previous libraries Lastly, I try to link the aforecompiled static and dynamic libraries into one project called "helloBeatlesII" which has the project directory "C:\helloBeatlesII" (note that this directory does not nest the other project directories). The linking process that I did is described below: To the "helloBeatlesII" solution, I added the solutions "libjohnpaul" and "libgeorgeringo"; then I changed the properties of the "helloBeatlesII" project to additionally point to the include directories of the other two projects on which it depends ("C:\libgeorgeringo\libgeorgeringo" & "C:\libjohnpaul\libjohnpaul"); added "libgeorgeringo" and "libjohnpaul" to the project dependencies of the "helloBeatlesII" project and made sure that the "helloBeatlesII" project was built last. Trying to compile this project gives me the following unsuccessful build: 1------ Build started: Project: helloBeatlesII, Configuration: Debug Win32 ------ 1Build started 10/13/2012 5:48:32 PM. 1InitializeBuildStatus: 1 Touching "Debug\helloBeatlesII.unsuccessfulbuild". 1ClCompile: 1 helloBeatles.cpp 1ManifestResourceCompile: 1 All outputs are up-to-date. 1helloBeatles.obj : error LNK2019: unresolved external symbol "void __cdecl georgeringo(void)" (?georgeringo@@YAXXZ) referenced in function _main 1helloBeatles.obj : error LNK2019: unresolved external symbol "void __cdecl johnpaul(void)" (?johnpaul@@YAXXZ) referenced in function _main 1E:\programming\cpp\vs-projects\cpp-cookbook\helloBeatlesII\Debug\helloBeatlesII.exe : fatal error LNK1120: 2 unresolved externals 1 1Build FAILED. 1 1Time Elapsed 00:00:01.34 ========== Build: 0 succeeded, 1 failed, 2 up-to-date, 0 skipped ========== At this point I decided to call in the cavalry. I am new to VS2010, so in all likelihood I am missing something straightforward.

  Read the article

• Integrating JavaFX Scene Builder in the IDEs

  - by Jerome Cambon

  I experienced recently using Scene Builder from Netbeans, Eclipse and IntelliJ IDEA. As you may know, Scene Builder is a standalone tool, that can be used independently of any IDE. But it can be very convenient to use it with your favorite IDE, for instance start it by double-clicking on an FXML file, or run samples delivered with Scene Builder.  I'm sharing here with you few tweaks that I had to do for a better integration. Scene Builder 1.1 Developer Preview should be installed before doing the tweaks. The steps below have been done on Windows 7. It should be very similar on both Mac OS and Linux. Please tell me if you find any issue on one of these 2 platforms. Netbeans 7.3 Netbeans 7.3 can be downloaded from here. Creating a New FXML project Part of the JavaFx projects, Netbeans allows to create a 'JavaFX FXML Application', that creates a JavaFx project based on FXML description. The FXML file will be editable with Scene Builder. Starting Scene Builder from Netbeans If SceneBuilder 1.1 is installed, Netbeans will discover it automatically.In case of issue, one can open the Options panel, Java section, JavaFx tab. Scene Builder home should appear here. You can then either Open the FXML file with Scene Builder, or edit it with the Netbeans FXML editor : When 'Open' is selected, Scene Builder appears on top of the Netbeans window : When 'Edit' is selected, the FXML is opened in the Netbeans FXML editor, which support syntax highlighting and completion : Using Scene Builder Samples Scene Builder provides Netbeans projects, that can be opened/run directly : Eclipse 4.2.1 + e(fx)clipse 0.1.1 JavaFX integration in Eclipse has been done with the e(fx)clipse plugin. A distribution bundle containing Eclipse and e(fx)clipse is provided here. Creating New FXML project All the JavaFX-related projects can be found in 'Other' section : First create a new JavaFX project: Enter the project name (Test here). JavaFX delivery will be found in the JRE. Then, create a 'New FXML Document': Enter the FXML file name (Sample here). You may also want to choose the FXML document root element (AnchorPane by default). Dynamic root is for advanced users which want to manage custom types. Starting Scene Builder from Eclipse Once created, you can then either Open the FXML file with Scene Builder, or Open it in the Eclipse FXML editor : Using Scene Builder Samples from Eclipse To use Scene Builder samples, first create a new JavaFX Project (from 'Other' section): Then, on the next panel, 'Link additionnal source': … and select the source directory of a Scene Builder example : HelloWorld here (the parent directory of the java package should be selected).Then, choose a 'Folder name' for your sample: You can now run the Scene Builder example by right-clicking the Main.java source file: IntelliJ IDEA 11.1.3 IntelliJ IDEA Community Edition can be downloaded from here. IntelliJ IDEA has no specific JavaFX integration. Creating New IntelliJ project from existing source Since IntelliJ has no JavaFX project knowledge, we are using the Scene Builder samples as a starting point. We are going to create a new Java project from the HelloWorld sample: Then, click twice on 'Next' (nothing to change), then 'Finish'. The 'HelloWorld' project is created. Starting Scene Builder from IntelliJ We need to tell the IDE that FXML files are opened with an external application. Then, the OS file association will be used. To do this, open the File->Settings panel. Then, select 'File Types' and 'Files opened in associated applications'. And add a new wildcard : '*.fxml' : Now, from the HelloWorld project, you can double-click on HelloWorld.fxml : Scene Builder window appears on top of the IntelliJ window : Using Scene Builder Samples from IntelliJ We need to tell IntelliJ that the fxml files must be copied in the build directory.To do that, from the HelloWorld directory, open the 'idea' section, and edit the 'compiler.xml' file. We need to add an '*.fxml' entry: Then, you can run the sample from HelloWorld project, by right-clicking the Main class:

  Read the article

• Bluetooth not found on BCM43228

  - by TK Kocheran

  I've got a Broadcom BCM43228 mPCIe card which came with my motherboard (ASUS ROG Maximus V Extreme, can't seem to find a link to what the card is) which is working great for WiFi right now, but I can't detect the Bluetooth hardware onboard. In Windows, I have full Bluetooth 4.0 support. $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.4 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 5 (rev c4) 00:1c.6 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 7 (rev c4) 00:1c.7 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 8 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1189 (rev a1) 01:00.1 Audio device: NVIDIA Corporation Device 0e0a (rev a1) 0d:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 0e:00.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 0f:01.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 0f:04.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 0f:05.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 0f:06.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 0f:07.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 0f:08.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 0f:09.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 10:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 12:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 01) 15:00.0 Network controller: Broadcom Corporation BCM43228 802.11a/b/g/n 17:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 01) The key line seems to be: 15:00.0 Network controller: Broadcom Corporation BCM43228 802.11a/b/g/n If I try to detect the Bluetooth card, I don't see anything: $ hcitool dev Devices: rfkill list all: Output lspci: Output lsusb: Output I finally found the card with usb-devices: T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0b05 ProdID=17b5 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=############ C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) I've heard that this card needs to have firmware injected into it in order to function. If that's the case, how do I do it?

  Read the article

• Silverlight Cream for February 07, 2011 -- #1043

  - by Dave Campbell

  In this Issue: Roy Dallal, Kevin Dockx, Gill Cleeren, Oren Gal, Colin Eberhardt, Rudi Grobler, Jesse Liberty, Shawn Wildermuth, Kirupa Chinnathambi, Jeremy Likness, Martin Krüger(-2-), Beth Massi, and Michael Crump. Above the Fold: Silverlight: "A Circular ProgressBar Style using an Attached ViewModel" Colin Eberhardt WP7: "Isolated Storage" Jesse Liberty Lightswitch: "How To Create Outlook Appointments from a LightSwitch Application" Beth Massi Shoutouts: Gergely Orosz has a summary of his 4-part series on Styles in Silverlight: Everything a Developer Needs To Know From SilverlightCream.com: Silverlight Memory Leak, Part 2 Roy Dallal has part 2 of his memory leak posts up... and discusses the results of runnin VMMap and some hints on how to make best use of it. Using a Channel Factory in Silverlight (instead of adding a Service Reference). With cows. Kevin Dockx has a post up for those of you that don't like the generated code that comes about when adding a service reference, and the answer is a Channel Factory... and he has an example app in the post that populates a list of cows... honest ... check it out. Getting ready for Microsoft Silverlight Exam 70-506 (Part 4) Gill Cleeren has Part 4 of his deep-dive into studying for the Silverlight Certification exam. This time out he's got probably half a gazillion links for working with data... seriously! Sync unlimited instances of one Silverlight application How about a cross-browser sync of an unlimited number of instances of the same Silverlight app... Oren Gal has just that going on, and discusses his first two attempts and how he finally honed in on the solution. A Circular ProgressBar Style using an Attached ViewModel Wow... check out what Colin Eberhardt's done with the "Progress Bar" ... using an Attached View Model which he discussed in a post a while back... these are awesome! WP7 - Professional Audio Recorder Rudi Grobler discusses an audio recorder for WP7 that uses the NAudio audio library for not only the recording but visualization. Isolated Storage Jesse Liberty's got his 30th 'From Scratch' post up and this time he's talking about Isolated Storage. Learning OData? MSDN and Shawn Wildermuth has the videos for you! Shawn Wildermuth produced a couple series of videos for MSDN on OData: Getting Started and Consuming OData... get the link on Shawn's post. Creating Sample Data from a Class - Page 1 Kirupa Chinnathambi shows us how to use a schema of your own design in Blend... yet still have Blend produce sample data A Pivot-Style Data Grid without the DataGrid Jeremy Likness discusses the lack of an open-source grid with dynamic columns ... let him know if you've done one! ... and then he continues on to demonstrate his build-out of the same. Synchronize a freeform drawing and a real path creation Martin Krüger has a few new samples up in the Expression Gallery. This first is taking mouse movement in an InkPresenter and creating path statements from it in a canvas and playing them back. How to: use Storyboard completed behaviors Martin Krüger's next post is about Storyboards and firing one off the end of another, in Blend... so he ended up producing a behavior for doing that... and it's in the Expression Gallery How To Create Outlook Appointments from a LightSwitch Application Beth Massi has a new Lightswitch post up... her previous was email from Lightswitch... this is Outlook appointments... pretty darn cool. Quick run through of the WP7 Developer Tools January 2011 Michael Crump has a really good Quick look at the new WP7 Dev Tools that were released last week posted on his blog Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Unclaimed user group prizes, Live meeting on Monday, Next weeks UG, SQLRelay and more prizes

  - by Testas

    Hi Everyone Firstly I want to let you know that I finally found the LINQ book prize winners and the list of people at the bottom of this email are owed a LINQ book. This will be given out at next week’s UG meeting Live meeting with Carolyn Chau, Program Manager at Microsoft on Monday! It is very rare that we get the opportunity to have a Live meeting with a Program Manager in Redmond. Carolyn Chau will be presenting PowerView next Monday at 8pm. Live meeting details can be found on http://sqlserverfaq.com/events/388/Live-Meeting-on-SQL-Server-2012-PowerView-with-Carolyn-Chau-Principal-Program-Manager-in-the-Reporting-Services-in-association-with-SQLPASS-SQLServerFAQ-and-SQLBits.aspx Next week’s UG!! We welcome Mark Broadbent to Manchester next week where he will be presenting his session on SQL Server 2012 on Windows Core. We also hand out the unclaimed prizes. Register at http://sqlserverfaq.com/events/369/Thursday-night-meeting-at-BSS-with-Chris-TestaONeill-and-Mark-Broadbent.aspx Chris Webb is in Manchester!!! Chris Webb will be speaking at the Manchester SQL Server UG on 4th July. He will also be running his Real World Cube Design and Performance Tuning with Analysis Services between the 3rd – 5th July. If you want to attend then you can sign up at the link below http://www.technitrain.com/coursedetail.php?c=13&trackingcode=FAQ SQLRelay and a Special Prize and Jamie Thomson comes to Manchester!!!! SQLRelay takes place in Manchester on the 22nd. We have a special guest, after years of asking Jamie Thomson is coming to Manchester. The SSIS Junkie will be gracing us with his presence with a talk on SSIS 2012. Also we have a prize. Know a friend or colleague who would benefit from SQLRelay? Get them to register at www.sqlserverfaq.com and then register for the event http://sqlserverfaq.com/events/373/ALL-DAY-TUESDAY-EVENT-12-hours-of-SQL-Server-2012-at-the-SQLRelay-meeting-at-the-COOP-Manchester.aspx Then send an email to [email protected] with the subject of SQLFriend with the name of your friend. If you are both at the SQLRelay event on the day and your names are pulled out of the hat you will win a PASS 2011 DVD and your friend will win the “Best of PASS DVD 2011” worth  $1000 courtesy of SQLPASS. The draw will take place between 4.30pm – 5pm on the day. SQLBits feedback!!!!! Attended SQLBits? We really need to know your opinion. Please fill out the survey for the days you attended If you attended any of the days at SQLBits please can you all fill out the following survey http://www.sqlbits.com/SQLBitsX If you attended the Thursday Training day then please fill out the following survey: http://www.sqlbits.com/SQLBitsXThursday If you attended the Friday Deep Dives day then please fill out the following survey: http://www.sqlbits.com/SQLBitsXFriday If you attended the Saturday Community day then please fill out the following survey: http://www.sqlbits.com/SQLBitsXSaturday Thanks   Chris and Martin   LINQ BOOK winners Andrew Birds Chris Kennedy Dave Carpenter David Forrester Ian Ringrose James Cullen James Simpson Kevan Riley Kirsty Hunter Martin Bell Martin Croft Michael Docherty Naga Anand Ram Mangipudi Neal Atkinson Nick Colebourn Pavel Nefyodov Ralph Baines Rick Hibbert saad saleh Simon Enion Stan Venn Steve Powell Stuart Quinn

  Read the article

• Building a Data Mart with Pentaho Data Integration Video Review by Diethard Steiner, Packt Publishing

  - by Compudicted

  Originally posted on: http://geekswithblogs.net/Compudicted/archive/2014/06/01/building-a-data-mart-with-pentaho-data-integration-video-review-again.aspx The Building a Data Mart with Pentaho Data Integration Video by Diethard Steiner from Packt Publishing is more than just a course on how to use Pentaho Data Integration, it also implements and uses the principals of the Data Warehousing (and I even heard the name of Ralph Kimball in the video). Indeed, a video watcher should be familiar with its concepts as the Star Schema, Slowly Changing Dimension types, etc. so I suggest prior to watching this course to consider skimming through the Data Warehouse concepts (if unfamiliar) or even better, read the excellent Ralph’s The Data Warehouse Tooolkit. By the way, the author expands beyond using Pentaho along to MySQL and MonetDB which is a real icing on the cake! Indeed, I even suggest the name of the course should be ‘Building a Data Warehouse with Pentaho’. To successfully complete the course one needs to know some Linux (Ubuntu used in the course), the VI editor and the Bash command shell, but it seems that similar requirements would also apply to the Windows OS. Additionally, knowing some basic SQL would not hurt. As I had said, MonetDB is used in this course several times which seems to be not anymore complex than say MySQL, but based on what I read is very well suited for fast querying big volumes of data thanks to having a columnstore (vertical data storage). I don’t see what else can be a barrier, the material is very digestible. On this note, I must add that the author does not cover how to acquire the software, so here is what I found may help: Pentaho: the free Community Edition must be more than anyone needs to learn it. Or even go into a POC. MonetDB can be downloaded (exists for both, Linux and Windows) from http://goo.gl/FYxMy0 (just see the appropriate link on the left). The author seems to be using Eclipse to run SQL code, one can get it from http://goo.gl/5CcuN. To create, or edit database entities and/or schema otherwise one can use a universal tool called SQuirreL, get it from http://squirrel-sql.sourceforge.net.   Next, I must confess Diethard is very knowledgeable in what he does and beyond. However, there will be some accent heard to the user of the course especially if one’s mother tongue language is English, but it I got over it in a few chapters. I liked the rate at which the material is being presented, it makes me feel I paid for every second Eventually, my impressions are: Pentaho is an awesome ETL offering, it is worth learning it very much (I am an ETL fan and a heavy user of SSIS) MonetDB is nice, it tickles my fancy to know it more Data Warehousing, despite all the BigData tool offerings (Hive, Scoop, Pig on Hadoop), using the traditional tools still rocks Chapters 2 to 6 were the most fun to me with chapter 8 being the most difficult.   In terms of closing, I highly recommend this video to anyone who needs to grasp Pentaho concepts quick, likewise, the course is very well suited for any developer on a “supposed to be done yesterday” type of a project. It is for a beginner to intermediate level ETL/DW developer. But one would need to learn more on Data Warehousing and Pentaho, for such I recommend the 5 star Pentaho Data Integration 4 Cookbook. Enjoy it! Disclaimer: I received this video from the publisher for the purpose of a public review.

  Read the article

• Building a Data Mart with Pentaho Data Integration Video Review by Diethard Steiner, Packt Publishing

  - by Compudicted

  Originally posted on: http://geekswithblogs.net/Compudicted/archive/2014/06/01/building-a-data-mart-with-pentaho-data-integration-video-review.aspx The Building a Data Mart with Pentaho Data Integration Video by Diethard Steiner from Packt Publishing is more than just a course on how to use Pentaho Data Integration, it also implements and uses the principals of the Data Warehousing (and I even heard the name of Ralph Kimball in the video). Indeed, a video watcher should be familiar with its concepts as the Star Schema, Slowly Changing Dimension types, etc. so I suggest prior to watching this course to consider skimming through the Data Warehouse concepts (if unfamiliar) or even better, read the excellent Ralph’s The Data Warehouse Tooolkit. By the way, the author expands beyond using Pentaho along to MySQL and MonetDB which is a real icing on the cake! Indeed, I even suggest the name of the course should be ‘Building a Data Warehouse with Pentaho’. To successfully complete the course one needs to know some Linux (Ubuntu used in the course), the VI editor and the Bash command shell, but it seems that similar requirements would also apply to the Weindows OS. Additionally, knowing some basic SQL would not hurt. As I had said, MonetDB is used in this course several times which seems to be not anymore complex than say MySQL, but based on what I read is very well suited for fast querying big volumes of data thanks to having a columnstore (vertical data storage). I don’t see what else can be a barrier, the material is very digestible. On this note, I must add that the author does not cover how to acquire the software, so here is what I found may help: Pentaho: the free Community Edition must be more than anyone needs to learn it. Or even go into a POC. MonetDB can be downloaded (exists for both, Linux and Windows) from http://goo.gl/FYxMy0 (just see the appropriate link on the left). The author seems to be using Eclipse to run SQL code, one can get it from http://goo.gl/5CcuN. To create, or edit database entities and/or schema otherwise one can use a universal tool called SQuirreL, get it from http://squirrel-sql.sourceforge.net.   Next, I must confess Diethard is very knowledgeable in what he does and beyond. However, there will be some accent heard to the user of the course especially if one’s mother tongue language is English, but it I got over it in a few chapters. I liked the rate at which the material is being presented, it makes me feel I paid for every second Eventually, my impressions are: Pentaho is an awesome ETL offering, it is worth learning it very much (I am an ETL fan and a heavy user of SSIS) MonetDB is nice, it tickles my fancy to know it more Data Warehousing, despite all the BigData tool offerings (Hive, Scoop, Pig on Hadoop), using the traditional tools still rocks Chapters 2 to 6 were the most fun to me with chapter 8 being the most difficult.   In terms of closing, I highly recommend this video to anyone who needs to grasp Pentaho concepts quick, likewise, the course is very well suited for any developer on a “supposed to be done yesterday” type of a project. It is for a beginner to intermediate level ETL/DW developer. But one would need to learn more on Data Warehousing and Pentaho, for such I recommend the 5 star Pentaho Data Integration 4 Cookbook. Enjoy it! Disclaimer: I received this video from the publisher for the purpose of a public review.

  Read the article

• How to mix textures in DirectX?

  - by tobsen

  I am new to DirectX development and I am wondering if I am taking the wrong route to achieve the following: I would like to mix three textures which contain transparent areas and some solid areas (Red, Blue, Green). The three textures should blend like shown in this example: How can I achieve that in DirectX (preferably in directx9)? A link or example code would be nice. Update: My rendering method looks like this and I still think I am doing it wrong, because the sprite only shows the last texture (nothing is rendered transparent or blended): void D3DTester::render() { d3ddevice->Clear(0, NULL, D3DCLEAR_TARGET, D3DCOLOR_XRGB(0,0,0), 1.0f, 0); d3ddevice->BeginScene(); d3ddevice->SetRenderState(D3DRS_ALPHABLENDENABLE, TRUE); d3ddevice->SetRenderState(D3DRS_SRCBLEND, D3DBLEND_ONE); d3ddevice->SetRenderState(D3DRS_DESTBLEND, D3DBLEND_ONE); LPD3DXSPRITE sprite=NULL; HRESULT hres = D3DXCreateSprite(d3ddevice, &sprite); if(hres != S_OK) { throw std::exception(); } sprite->Begin(D3DXSPRITE_ALPHABLEND); std::vector<LPDIRECT3DTEXTURE9>::iterator it; for ( it=textures.begin() ; it < textures.end(); it++ ) { sprite->Draw(*it, NULL, NULL, NULL, 0xFFFFFFFF); } sprite->End(); d3ddevice->EndScene(); d3ddevice->Present(NULL, NULL, NULL, NULL); } The resulting image looks like this: But I need it to look like this instead: Update2: I figured out that I have to SetRenderState after I use sprite->Begin(D3DXSPRITE_ALPHABLEND); thanks to the hint by Josh Petrie. However, by using this: sprite->Begin(D3DXSPRITE_ALPHABLEND); d3ddevice->SetRenderState(D3DRS_ALPHABLENDENABLE, TRUE); d3ddevice->SetRenderState(D3DRS_SRCBLEND, D3DBLEND_ONE); d3ddevice->SetRenderState(D3DRS_DESTBLEND, D3DBLEND_ONE); std::vector<LPDIRECT3DTEXTURE9>::iterator it; for ( it=textures.begin() ; it < textures.end(); it++ ) { sprite->Draw(*it, NULL, NULL, NULL, 0xFFFFFFFF); } sprite->End(); The sprites colors are becoming transparent towards the background scene e.g.: if I use d3ddevice->Clear(0, NULL, D3DCLEAR_TARGET, D3DCOLOR_XRGB(0,100,21), 1.0f, 0); the result looks like: Is there any way to avoid that? I would like the sprites be transparent to each other but to be still solid to the background. Update3: After having sombody explained to me, how to do what @LaurentCouvidou and @JoshPetrie suggested, I have a working solution and therfore accept the answer: d3ddevice->BeginScene(); D3DCOLOR white = D3DCOLOR_RGBA((UINT)255, (UINT)255, (UINT)255, 255); D3DCOLOR black = D3DCOLOR_RGBA((UINT)0, (UINT)0, (UINT)0, 255); sprite->Begin(D3DXSPRITE_ALPHABLEND); sprite->Draw(pTextureRed, NULL, NULL, NULL, black); sprite->Draw(pTextureGreen, NULL, NULL, NULL, black); sprite->Draw(pTextureBlue, NULL, NULL, NULL, black); sprite->End(); sprite->Begin(D3DXSPRITE_ALPHABLEND); d3ddevice->SetRenderState(D3DRS_ALPHATESTENABLE, TRUE); d3ddevice->SetRenderState(D3DRS_BLENDOP, D3DBLENDOP_ADD); d3ddevice->SetRenderState(D3DRS_SRCBLEND, D3DBLEND_ONE); d3ddevice->SetRenderState(D3DRS_DESTBLEND, D3DBLEND_ONE); sprite->Draw(pTextureRed, NULL, NULL, NULL, white); sprite->Draw(pTextureGreen, NULL, NULL, NULL, white); sprite->Draw(pTextureBlue, NULL, NULL, NULL, white); sprite->End(); d3ddevice->EndScene(); d3ddevice->Present(NULL, NULL, NULL, NULL);

  Read the article

• Some thoughts on email hosting for one’s own domain

  - by jamiet

  I have used the same email providers for my own domains for a few years now however I am considering moving over to a new provider. In this email I’ll share my current thoughts and hopefully I’ll get some feedback that might help me to decide on what to do next. What I use today I have three email addresses that I use primarily (I have changed the domains in this blog post as I don’t want to give them away to spammers): [email protected] – My personal account that I give out to family and friends and which I use to register on websites [email protected]  - An account that I use to catch email from the numerous mailing lists that I am on [email protected] – I am a self-employed consultant so this is an account that I hand out to my clients, my accountant, and other work-related organisations Those two domains (jtpersonaldomain.com & jtworkdomain.com) are both managed at http://domains.live.com which is a fantastic service provided by Microsoft that for some perplexing reason they never bother telling anyone about. It offers multiple accounts (I have seven at jtpersonaldomain.com though as already stated I only use two of them) which are accessed via Outlook.com (formerly Hotmail.com) along with usage reporting plus a few other odds and sods that I never use. Best of all though, its totally free. In addition, given that I have got both domains hosted using http://domains.live.com I can link my various accounts together and switch between them at Outlook.com without having to login and logout: N.B. You’ll notice that there are two other accounts listed there in addition to the three I already mentioned. One is my mum’s account which helps me provide IT support/spam filtering services to her and the other is the donation account for AdventureWorks on Azure. I find that linking feature to be very handy indeed. Finally, http://domains.live.com is the epitome of “it just works”. I set up jtworkdomain.com at http://domains.live.com over three years ago and I am pretty certain I haven’t been back there even once to administer it. Proposed changes OK, so if I like http://domains.live.com so much why am I considering changing? Well, I earn my corn in the Microsoft ecosystem and if I’m reading the tea-leaves correctly its looking increasingly likely that the services that I’m going to have to be familiar with in the future are all going to be running on top of and alongside Windows Azure Active Directory and Office 365 respectively. Its clear to me that Microsoft’s are pushing their customers toward cloud services and, like it or lump it, data integration developers like me may have to come along for the ride. I don’t think the day is too far off when we can log into Windows Azure SQL Database (aka SQL Azure), Team Foundation Service, Dynamics etc… using the same credentials that are currently used for Office 365 and over time I would expect those things to get integrated together a lot better – that integration will be based upon a Windows Azure Active Directory identity. This should not come as a surprise, in my opinion Microsoft’s whole enterprise play over the past 15 or 20 years can be neatly surmised as “get people onto Windows Server and Active Directory then upsell from there” – in the not-too-distant-future the only difference is that they’re trying to do it in the cloud. I want to get familiar with these services and hence I am considering moving jtworkdomain.com onto Office 365. I’ll lose the convenience of easily being able to switch to that account at Outlook.com and moreover I’ll have to start paying for it (I think it’ll be about fifty quid a year – not a massive amount but its quite a bit more than free) but increasingly this is beginning to look like a move I have to make. So that’s where my head is at right now. Anyone have any relevant thoughts or experiences to share? Please let me know in the comments below. @Jamiet

  Read the article

• Silverlight Cream for January 16, 2011 -- #1029

  - by Dave Campbell

  In this Issue: Michael Washington, Jesse Liberty, Deborah Kurata(-2-, -3-, -4-), Sergey Barskiy(-2-), Miroslav Nedyalkov, Jeff Prosise, and Matthias Shapiro(-2-). Above the Fold: Silverlight: "Building a Multi-Page Silverlight LOB Application" Deborah Kurata WP7: "Windows Phone 7 [Controls] Project" Sergey Barskiy Sketchflow: "Sketchflow To Final" Michael Washington From SilverlightCream.com: Sketchflow To Final Check out this post by Michael Washington detailing the Sketchflow he did of his app, and how the final result tracks amazingly well. Windows Phone From Scratch #19 – MVVM Light Toolkit Soup To Nuts #4 Continuing to try to catch up to Jesse Liberty is this post, number 19 in the Windows Phone series and the 4th in that series about MVVMLight, and discussing binding a collection in the ViewModel to a ListBox in the view. Building a Multi-Page Silverlight LOB Application Deborah Kurata has the first 4 parts up (in 2 days) in a 6-part tutorial series she's doing on building a Silverlight LOB app. The first post was an intro and link to the rest as they become available. This 2nd post is getting the app newed up and making sure you've got your head wrapped around multiple pages. Theming a Silverlight Application using Existing Themes Deborah Kurata's next part is about getting started with themes in your app using the themes provided in the toolkit specifically. Theming a Silverlight Application using Custom Themes Deborah Kurata's next tutorial in the series is also about themes, but this time it's about custom themes... or rather customized from a 'standard' one in this case. Adding a New Page to a Multi-Page Silverlight Application Deborah Kurata's last available post in the tutorial series is this one on adding a new page to the app. Windows Phone 7 Project Sergey Barskiy has a pair of posts up about a calendar control that he is building and has out on CodePlex... nice-looking control too! Windows Phone 7 Controls Project Update Sergey Barskiy's second post is an update to the calendar... the biggest update being the ability to use the Toolkit context menu. How to Create Ad Rotator with Telerik TransitionControl and CoverFlow control for Silverlight Miroslav Nedyalkov uses the Telerik TransitionControl and CoverFlow controls to produce a great-looking ad rotator using any ContentControl or ListBox... very nice demo on the page.... Building Touch Interfaces for Windows Phones, Part 2 Jeff Prosise has part 2 of his tutorial series on WP7 Touch Interfaces up... and he's processing touch events directly in this one. Fixing the ListPicker / ScrollViewer Problem in Windows Phone 7 Matthias Shapiro has a couple of posts out that I've missed... this one is on an issue with ListPickers in a ScrollViewer where the listpicker gets hit rather than the scroll, and of course he has a work-around... but you'll need the source for the ListPicker to do it. Embedding a Sound File in Windows Phone 7 app (Silverlight) The next post by Matthias Shapiro is an explanation of embedding a sound file in a WP7 app with 2 conditions: 1) it downloads with your app, and 2) it plays no matter what. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Chrome Web Browser Messages: Some Observations

  - by ultan o'broin

  I'm always on the lookout for how different apps handle errors and what kind of messages are shown (I probably need to get out more), I use this 'research' to reflect on our own application error messages patterns and guidelines and how we might make things better for our users in future. Users are influenced by all sorts of things, but their everyday experiences of technology, and especially what they encounter on the internet, increasingly sets their expectations for the enterprise user experience too. I recently came across a couple of examples from Google's Chrome web browser that got me thinking. In the first case, we have a Chrome error about not being able to find a web page. I like how simple, straightforward messaging language is used along with an optional ability to explore things a bit further--for those users who want to. The 'more information' option shows the error encountered by the browser (or 'original' error) in technical terms, along with an error number. Contrasting the two messages about essentially the same problem reveals what's useful to users and what's not. Everyone can use the first message, but the technical version of the message has to be explicitly disclosed for any more advanced user to pursue further. More technical users might search for a resolution, using that Error 324 number, but I imagine most users who see the message will try again later or check their URL again. Seems reasonable that such an approach be adopted in the enterprise space too, right? Maybe. Generally, end users don't go searching for solutions based on those error numbers, and help desk folks generally prefer they don't do so. That's because of the more critical nature of enterprise data or the fact that end users may not have the necessary privileges to make any fixes anyway. What might be more useful here is a link to a trusted source of additional help provided by the help desk or reputable community instead. This takes me on to the second case, this time more closely related to the language used in messaging situations. Here, I first noticed by the using of the (s) approach to convey possibilities of there being one or more pages at the heart of the problem. This approach is a no-no in Oracle style terms (the plural would be used) and it can create translation issues (though it is not a show-stopper). I think Google could have gone with the plural too. However, of more interest is the use of the verb "kill", shown in the message text and as an action button label. For many writers, words like "kill" and "abort" are to be avoided as they can give offense. I am not so sure about that judgment, as really their use cannot be separated from the context. Certainly, for more technical users, they're fine and have been in use for years, so I see no reason to avoid these terms if the audience has accepted them. Most end users too, I think would find the idea of "kill" usable and may even use the term in every day speech. Others might disagree--Apple uses a concept of Force Quit, for example. Ultimately, the only way to really know how to proceed is to research these matter by asking users of differing roles and expertise to perform some tasks, encounter these messages and then make recommendations based on those findings for our designs. Something to do in 2011!

  Read the article

• Silverlight Cream for November 16, 2011 -- #1167

  - by Dave Campbell

  In this Issue: Michael Crump, Andrea Boschin, Michael Sync, WindowsPhoneGeek(-2-), Erno de Weerd, Jesse Liberty, Derik Whittaker, Antoni Dol, Walter Ferrari, and Jeff Blankenburg(-2-). Above the Fold: Silverlight: "10 Laps around Silverlight 5 (Part 6 of 10)" Michael Crump WP7: "31 Days of Mango | Day #2: Device Status" Jeff Blankenburg Metro/WinRT/W8: "Lighting up your C# Metro apps by being a Share Target" Derik Whittaker Shoutouts: Michael Palermo's latest Desert Mountain Developers is up Michael Washington's latest Visual Studio #LightSwitch Daily is up SilverlightShow has announced a webinar you probably don't want to miss: Webinar – Introduction to XAML Development on Windows 8 Check out the top 5 from last week at SilverlightShow: SilverlightShow for November 07 - 13, 2011 From SilverlightCream.com: 10 Laps around Silverlight 5 (Part 6 of 10) Michael Crump covers a lot of territory in this Part 6 of his Silverlight 5 Beta series at SilverlightShow: P/Invoke, Multiple Windows, and Full Trust Windows Phone 7.5 - Manipulating camera stream Andrea Boschin has Part 4 of his Mango series up at SilverlightShow. He's discussing accessing the raw stream from the camera and saving it to a file. Blend 4 + VS 2011 (Preview) = Problem? Michael Sync reports a problem with Blend 4 and the VS2011 preview... followed up by a set of scripts that were posted on Connect to make the problem go away (at least for Michael) Windows Phone Toolkit MultiselectList in depth | Part1: key concepts and API WindowsPhoneGeek begins a series on the MultiselectList in the Phone Toolkit... if you've seen his tutorials, you know they're great... this one is no exception.. lots of code, info and notes getting you on-board with the features Getting Started with Windows Phone Alarms WindowsPhoneGeek next takes a sidestep from his new series and has this post on Alarms in WP7 apps .. one of the type of scheduled actions in WP7.1 ... good write-up, pictures and code Using AppHarbor, Bitbucket and Mercurial with ASP.NET and Silverlight – Part 3 Membership and Role Provider in SQL Server Erno de Weerd's part 3 of his series is up... adding Role and Membership to his application... check it out in this 17-step tutorial Yet Another Podcast #51–Shawn Wildermuth: //build, Xaml Programming & Beyond Jesse Liberty has another of his Yet Another Podcasts up and he's talking with Jon Galloway and Shawn Wildermuth... hear what *that* trio has to say about post //BUILD, and all things XAML Lighting up your C# Metro apps by being a Share Target Derik Whittaker continues to work with Metro... evidenced by this post on wiring your app up to be a Share Target .. allowing your app to consume data from other apps Photoshop in METRO style 2: Filters Antoni Dol follows up his Photoshop in Metro post with this one on filters... he's got some great screenshots... was hoping to see a link to the code... maybe I missed it! Silverlight and Sharepoint working together: a Silverlight menu for Sharepoint - Part 1 Walter Ferrari has part 1 of a series up at SilverlightShow talking about Sharepoint and Silverlight, and using Silverlight Navigation in place of what Sharepoint offers up. 31 Days of Mango | Day #2: Device Status Jeff Blankenburg is motoring along on his 31 Days of Mango. This is his Day 2 post and all about DeviceStatus, or just about everything you would like to know about your user's phone 31 Days of Mango | Day #3: Alarms and Reminders Day 3 of Jeff Blankenburg's series is about Alarms and Reminders... a way to alert your user that something needs to be done... you can create, edit, and delete them as needed Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Silverlight Cream for December 13, 2010 -- #1010

  - by Dave Campbell

  In this Issue: Rénald Nollet, Benjamin Gavin, Dennis Doomen, Tim Greenfield, Mike Taulty, Jeff Blankenburg, Michael Crump, Laurent Duveau, Dragos Manolescu, KeyboardP, Yochay Kiriaty. Above the Fold: Silverlight: "Silverlight RIA Services and Basic, Anonymous Authentication" Benjamin Gavin WP7: "lving Circular Navigation in Windows Phone Silverlight Applications" Yochay Kiriaty SQL Azure: "SQL Azure Database Manager – Part 1 : How to connect to your SQL Azure DB" Rénald Nollet Shoutouts: Yochay Kiriaty has a post up on the Windows Phone Devloper Blog about open source (MSPL) projects helping WP7 devs: Windows Phone Recipes – Helping the Community Jesse Liberty's latest Yet Another Podcast is up and thie time it's Joe Stagner: Yet Another Podcast #18 – Joe Stagner Josh Schwartzberg sent me this link to what is apparently his yearly web-only rock Christmas album: MetalXmas... done in Silverlight and RIA Services From SilverlightCream.com: SQL Azure Database Manager – Part 1 : How to connect to your SQL Azure DB Rénald Nollet posted Part 1 of a series on a SQL Azure database manager all in Silverlight... has a live demo running, some description, and is making us wait for the next part! Silverlight RIA Services and Basic, Anonymous Authentication Benjamin Gavin has a quick post up resolving a basic RIA Services problem that I bet a lot of folks are looking for the answer on... like 500 series errors... cool little find he ferreted out... A night of Silverlight, WPF, unit testing and Caliburn Micro Dennis Doomen in concert with his employer gave a couple talks at the local DotNED user group, and covered literally a cornucopia of topics... slides, and example code for both talks... lotsa material here... Tim Greenfield on PuzzleTouch WP7 Application Tim Greenfield is the latest WP7 app developer to be interviewed by the SilverlightShow crew... lots of interesting comments and insight from Tim. Rebuilding the PDC 2010 Silverlight Application (Part 4) Mike Taulty has part 4 of his PDC 2010 Silverlight app construction project up and is taking the app into Blend, and the considerations that brought to the table. What I Learned In WP7 – Issue #2 Jeff Blankenburg continues his "What I Learned" series with this discussion about fonts, the Non-Linear Navigation service I mention below, and possible WP7 jobs. Part 3 of 4 : Tips/Tricks for Silverlight Developers Michael Crump has Part 3 of his Tips/Tricks up today. Lots of goodies this time: underlining in a TextBlock, getting browser info, startup params, VisualTreeHelper, and child windows. My Windows Phone 7 presentation in Montreal Laurent Duveau gave a WP7 presentation in Montreal as part of the Microsoft Windows Phone 7 Developer's Briefing, and has posted his materials and slide deck WP7 Code: Mocking Event Streams with IEnumerable Dragos Manolescu has a very cool post up on using IEnumerable to Mock event streams by leveraging the IObservable/IEnumerable duality, and uses the 2D bubble app that you can run and test in the emulator without needing an accelerometer Transparent Wallpapers – Video Tutorial KeyboardP has had so many queries about his Transparent wallpaper for WP7 that he produced a video tutorial for it... Solving Circular Navigation in Windows Phone Silverlight Applications Yochay Kiriaty discusses the first recipe they are releasing ... see the shoutout above, a Nonlinear Navigation Service ... to help with apps that have loops in navigation. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• A View from the Top – Jan Ackerman (VP APAC Recruiting)

  - by user769227

  This week, Headhunt Magazine in Singapore, took the opportunity to publish an interview with Jan Ackerman who is Vice President for Recruitment for Asia Pacific here at Oracle. The link to the online interview can be found here. Below is the interview in full that was published in Headhunt Magazine.  A View from the Top – Jan Ackerman Written by HeadHunt on August 16, 2012 · Leave a Comment By Susheela Menon Jan Ackerman is the Vice President for Recruiting in Asia Pacific and Japan at Oracle. Which particular personal trait do you attribute your professional success to? Perseverance has been the most important trait that has attributed to my professional success. Endurance and perseverance combined to win in the end has always been a great credo. I find that this trait carries through in my professional as well as my personal life. I enjoy sport fishing and find that perseverance with a great deal of patience in this hobby is critical to the overall enjoyment and success in this sporting activity. In the same way, this doggedness – steadfastness with persistence – and tenacity toward an unyielding course of action has served me well in reaching goals and thus greater success. What’s the biggest challenge you have faced in your career so far? I have to constantly keep pace with ever changing technology in my career. The industry changes rapidly and requires me to stay on top of the latest trends and advancements. Outside of work, I like to develop software as a hobby and in order to ensure that what I am developing will meet what the business needs, I have to continually innovate and stay current on the latest trends in the industry to deliver a solution that will delight the end- user. Best career advice you have ever received. Always be forthright and honest with your customers and peers; mixed with a “Can Do” attitude, a great and fulfilling career can be yours to have and hold. What makes Oracle a great place to be in? The freedom to innovate and pave new avenues of success is one of the greatest things about working here at Oracle. We are always looking to grow and improve our business for our customers and we are always adapting to present and future industry demands. This means we are always looking to change, to perform better and to do things differently. All these create a culture and spirit of innovation and success. What motivates you to be in the HR sector? I really like working with and helping people. HR is all about “the people” in the organisation, and staying focused every day on making things better for the Oracle team gives me a great deal of happiness. Describe your leadership style. I am very direct and goal- oriented. I provide ideas and guidance and then give the team all the freedom they need to reach a successful outcome. I can also be a very “roll up your sleeves” kind of manager when the task needs a bit of a push. What’s the biggest business challenge you see in your industry right now? The ability to keep pace with all the convergence in the industry and to continue to stay focused on delivering top talent to serve Oracle’s customers well. Our unique Recruiting Model has served us well in meeting these needs. We are well-placed in this goal and look forward to maintain Oracle’s leadership role in the industry.

  Read the article

• How To Quickly Reboot Directly from Windows 7 to XP, Vista, or Ubuntu

  - by The Geek

  One of the biggest annoyances with a dual-boot system is having to wait for your PC to reboot to select the operating system you want to switch to, but there’s a simple piece of software that can make this process easier. This guest article was written by Ryan Dozier from the Doztech tech blog. With a small piece of software called iReboot we can skip the above step all together and instantly reboot into the operating system we want right from Windows. Their description says: “Instead of pressing restart, waiting for Windows to shut down, waiting for your BIOS to post, then selecting the operating system you want to boot into (within the bootloader time-limit!); you just select that entry from iReboot and let it do the rest!” Don’t worry about iReboot reconfiguring  your bootloader or any dual boot configuration you have. iReboot will only boot the selected operating system once and go back to your default settings. Using iReboot iReboot is quick and easy to install. Just download it, link below, run through the setup and select the default configuration. iReboot will automatically figure out what operating systems you have installed and appear in the taskbar. Go over to the taskbar and right click on the iReboot icon and select which operating system you want to reboot into. This method will add a check mark on the operating system you want to boot into. On your next reboot the system will automatically load your choice and skip the Windows Boot Manager. If you want to reboot automatically just select “Reboot on Selection” in the iReboot menu.   To be even more productive, you can install iReboot into each Windows operating system to quickly access the others with a few simple clicks.   iReboot does not work in Linux so you will have to reboot manually. Then wait for the Windows Boot Manager to load and select your operating system.   Conclusion iReboot works on  Windows XP, Windows Vista,  and Windows 7 as well as 64 bit versions of these operating systems. Unfortunately iReboot is only available for Windows but you can still use its functionality in Windows to quickly boot up your Linux machine. A simple reboot in Linux will take you back to Windows Boot Manager. Download iReboot from neosmart.net Editor’s note: We’ve not personally tested this software over at How-To Geek, but Neosmart, the author of the software, generally makes quality stuff. Still, you might want to test it out on a test machine first. If you’ve got any experience with this software, please be sure to let your fellow readers know in the comments. Similar Articles Productive Geek Tips Restart the Ubuntu Gnome User Interface QuicklyKeyboard Ninja: 21 Keyboard Shortcut ArticlesTest Your Computer’s Memory Using Windows Vista Memory Diagnostic ToolEnable or Disable UAC From the Windows 7 / Vista Command LineSet Windows as Default OS when Dual Booting Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily QuicklyCode Provides Cheatsheets & Other Programming Stuff Download Free MP3s from Amazon

  Read the article

• Subscribable World Cup 2010 Calendar

  - by jamiet

  I bang on quite a lot on this blog about ways in which data can get published over the web and one of the most interesting ways, in my opinion, of publishing data in a structured manner that is well understood is to use the iCalendar specification. There isn’t much information in the world that doesn’t have some concept of “when” so iCalendar is a great way of distributing that information. You have probably used iCalendar at some point without even knowing about it. All files with a .ics suffix are iCalendar format files and that is why you can happily import them into Outlook, Hotmail Calendar, Google Calendar etc… where they can be parsed and have the semantic data (when, where and who) extracted from them. Importing of iCalendar format data is really only half the trick though; in my opinion the real value of iCalendar-formatted calendar is the ability to subscribe to them. Subscribing has a simple benefit over importing but that single benefit is of massive importance: a subscriber to an iCalendar calendar can periodically check to see if any updates have been made and, if they have, automatically update the local copy. The real benefit to the user is the productivity gain – a single update to an iCalendar means that all subscribers are automatically made aware of the change and there is zero effort on the part of the subscriber; as my former colleague Howard van Rooijen is fond of saying, “work smarter not harder” – nowhere is this edict more ably demonstrated than subscribing versus importing of calendars. If you want to read some more thoughts about iCalendar then go and read my past blog post Calendar syndication - My big hope for 2009's breakthrough technology or better still go and seek out Jon Udell who speaks very authoritatively on the issue of iCalendar. With this subject of iCalendar on my mind I was interested to discover (via Steve Clayton’s blog post Download the world cup fixtures) that the BBC had made a .ics file available containing all of the matches in the upcoming World Cup. As you can probably guess this was a file that was made available so that it could be imported into your calendar of choice. It had one obvious downside though, right now nobody knows who is going to be playing in the knock-out stages so the calendar looks like this: with no teams being named after 25th June. How much more useful would this calendar have been if the BBC had made it possible to subscribe to the calendar instead, thus the calendar could be updated with the teams for the knock out stages when they are known and every subscriber would have a permanently up-to-date record of all the fixtures in their calendar. Better still, the calendar could be updated with match results as well or perhaps even post a match report from the BBC sport pages; when calendars are made subscribable a sea of opportunity opens up for distribution of information. So with that in mind I have decided to go one better than the BBC. I have imported their .ics into a brand new Hotmail calendar and made it publicly available at the following URLs: HTML http://cid-dc1ed121af0476be.calendar.live.com/calendar/World+Cup+2010/index.html iCalendar webcal://cid-dc1ed121af0476be.calendar.live.com/calendar/World+Cup+2010/calendar.ics The link you’re really interested in is the second one - click on that and it should open up in your calendar software of choice. Or, if you want to view it in an online calendar such as Hotmail Calendar or Google Calendar, copy and paste that URL into the appropriate place. I shall endeavour to keep the calendar updated throughout the World Cup and even if I don’t you’re no worse off than if you had imported the BBC’s .ics file so why not give it a try? If I do keep it up to date then you will have a permanent record of the 2010 World Cup available in your calendar. Forever. If you have your calendar synced to your smartphone then you’ll be carrying match reports around with you without you having to do a single thing. Surely that’s worth a quick click isn’t it?   If you have any thoughts let me have them in the comments below. Thanks for reading. @Jamiet Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• Android - passing data between Activities

  - by Bill Osuch

  (To follow along with this, you should understand the basics of starting new activities: Link ) The easiest way to pass data from one activity to another is to create your own custom bundle and pass it to your new class. First, create two new activities called Search and SearchResults (make sure you add the second one you create to the AndroidManifest.xml file!), and create xml layout files for each. Search's file should look like this: <?xml version="1.0" encoding="utf-8"?> <LinearLayout     xmlns:android="http://schemas.android.com/apk/res/android"     android:layout_width="fill_parent"     android:layout_height="fill_parent"     android:orientation="vertical">     <TextView          android:layout_width="fill_parent"      android:layout_height="wrap_content"      android:text="Name:"/>     <EditText                android:id="@+id/edittext"         android:layout_width="fill_parent"         android:layout_height="wrap_content"/>     <TextView          android:layout_width="fill_parent"         android:layout_height="wrap_content"         android:text="ID Number:"/>     <EditText                android:id="@+id/edittext2"                android:layout_width="fill_parent"                android:layout_height="wrap_content"/>     <Button           android:id="@+id/btnSearch"          android:layout_width="fill_parent"         android:layout_height="wrap_content"         android:text="Search" /> </LinearLayout> and SearchResult's should look like this: <?xml version="1.0" encoding="utf-8"?> <LinearLayout     xmlns:android="http://schemas.android.com/apk/res/android"     android:layout_width="fill_parent"     android:layout_height="fill_parent"     android:orientation="vertical">     <TextView          android:id="@+id/txtName"         android:layout_width="fill_parent"         android:layout_height="wrap_content"/>     <TextView          android:id="@+id/txtState"         android:layout_width="fill_parent"         android:layout_height="wrap_content"         android:text="No data"/> </LinearLayout> Next, we'll override the OnCreate method of Search: @Override public void onCreate(Bundle savedInstanceState) {     super.onCreate(savedInstanceState);     setContentView(R.layout.search);     Button search = (Button) findViewById(R.id.btnSearch);     search.setOnClickListener(new View.OnClickListener() {         public void onClick(View view) {                           Intent intent = new Intent(Search.this, SearchResults.class);              Bundle b = new Bundle();                           EditText txt1 = (EditText) findViewById(R.id.edittext);             EditText txt2 = (EditText) findViewById(R.id.edittext2);                                      b.putString("name", txt1.getText().toString());             b.putInt("state", Integer.parseInt(txt2.getText().toString()));                              //Add the set of extended data to the intent and start it             intent.putExtras(b);             startActivity(intent);          }     }); } This is very similar to the previous example, except here we're creating our own bundle, adding some key/value pairs to it, and adding it to the intent. Now, to retrieve the data, we just need to grab the Bundle that was passed to the new Activity and extract our values from it: @Override public void onCreate(Bundle savedInstanceState) {     super.onCreate(savedInstanceState);     setContentView(R.layout.search_results);     Bundle b = getIntent().getExtras();     int value = b.getInt("state", 0);     String name = b.getString("name");             TextView vw1 = (TextView) findViewById(R.id.txtName);     TextView vw2 = (TextView) findViewById(R.id.txtState);             vw1.setText("Name: " + name);     vw2.setText("State: " + String.valueOf(value)); }

  Read the article

• How Can I Improve This Card-Game AI?

  - by James Burgess

  Let me get this out there before anything else: this is a learning exercise for me. I am not a game developer by trade or hobby (at least, not seriously) and am purely delving into some AI- and 3D-related topics to broaden my horizons a bit. As part of the learning experience, I thought I'd have a go at developing a basic card game AI. I selected Pit as the card game I was going to attempt to emulate (specifically, the 'bull and bear' variation of the game as mentioned in the link above). Unfortunately, the rule-set that I'm used to playing with (an older version of the game) isn't described. The basics of it are: The number of commodities played with is equal to the number of players. The bull and bear cards are included. All but two players receive 8 cards, two receive 9 cards. A player can win the round with 7 + bull, 8, or 8 + bull (receiving double points). The bear is a penalty card. You can trade up to a maximum of 4 cards at a time. They must all be of the same type, but can optionally include the bull or bear (so, you could trade A, A, A, Bull - but not A, B, A, Bull). For those who have played the card game, it will probably have been as obvious to you as it was to me that given the nature of the game, gameplay would seem to resemble a greedy algorithm. With this in mind, I thought it might simplify my AI experience somewhat. So, here's what I've come up with for a basic AI player to play Pit... and I'd really just like any form of suggestion (from improvements to reading materials) relating to it. Here it is in something vaguely pseudo-code-ish ;) While AI does not hold 7 similar + bull, 8 similar, or 8 similar + bull, do: 1. Establish 'target' hand, by seeing which card AI holds the most of. 2. Prepare to trade next-most-numerous card type in a trade (max. held, or 4, whichever is fewer) 3. If holding the bear, add to (if trading <=3 cards) or replace in (if trading 4 cards) hand. 4. Offer cards for trade. 5. If cards are accepted for trade within X turns, continue (clearing 'failed card types'). Otherwise: a. If only one card remains in the trade, go to #6. Otherwise: i. Remove one non-penalty card from the trade. ii. Return to #5. 6. Add card type to temporary list of failed card types. 7. Repeat from #2 (excluding 'failed card types'). I'm aware this is likely to be a sub-optimal way of solving the problem, but that's why I'm posting this question. Are there any AI- or algorithm-related concepts that I've missed and should be incorporating to make a better AI? Additionally, what are the flaws with my AI at present (I'm well aware it's probably far from complete)? Thanks in advance!

  Read the article

• Mandatory look back at 2010

  - by Bertrand Le Roy

  Yeah, it's one of those posts, sorry. First, the mildly depressing: the most popular post on this blog this year with 47,000 hits was a post from last year about a fix to a bug in ASP.NET. A content-less post except for that link to the KB article that people should have found by going directly to the support site in the first place. Then, the really depressing: the second most popular post this year with 34,000 hits was a post from 2005 about how to display message boxes on a web page. I mean come on. This was kind of fun five years ago and it did solve one of the most common n00b mistakes VB programmers trying to move to the web were making. But come on, we've traveled about 4.7 billion miles around the Earth since then. Do people still do that kind of stuff? I should probably put a big red banner on top of this post. Oh [supernatural entity of your choice]. Hand me that gun, please. Third most popular post with 24,000 hits is from 2004. It's about how to set a session variable before redirecting. That problem has been fixed a long time ago. Oh well. Fourth most popular post. 21,000 hits. 2007. How to work around a stupid bug in ASP.NET Ajax 1.0. Fixed in ASP.NET 3.5? ASP.NET Ajax 1.0? Need I say more? The fifth one (20,000 hits) is an old post as well but I'm kind of fond of it: it's about that photo album handler I've been organically growing for a few years. It reminds me that I need to refresh it and make a new release. Good SEO title too. Back to insanity with the sixth one (16,000) that's about working around a bug in IE6. IE6. Please just refuse to pander to that browser any more. It's about time. Let's move on, please. Actually, the first post from 2010 is 15th in the list. We have a trio of these actually with server-side image resizing and FluentPath. So what happened? Well, I like the ad money, but not to the point that I'm going to write my stuff to inflate it. Actually I think if I tried I would fail miserably (I mean, I would fail worse). What really happened this year was new stuff: Orchard, FluentPath and the stuff with the Netduino. That stuff needs time to get off the ground but my hope is that it's going to be useful in the long run and that five years from now I'll be lamenting on how well those posts are still doing. So, no regret. 2010 was a good year. Oh, and I was on This Developer's Life this year! Yay! Anyways, thank you all for reading me. Please continue doing that. And happy 2011!

  Read the article

• Do MORE with WebCenter

  - by Michael Snow

  We’ve been extremely busy here on the Oracle WebCenter team. We hope that you’ve all be keeping up with the interesting news each week. Last week was jammed full of GartnerPCC and Gartner360 buzz. If you missed any of the highlights – be sure to check out both Kellsey’s post from last week: Gartner PCC: A Shovel & Some Ah-Ha's and Christie’s overview of Loren Weinberg’s PCC presentation: "Here Today, Gone Tomorrow: Engage Your Customers or Lose Them"  . This week, we’ll be focusing on “Doing More with WebCenter” leading up to a great webcast scheduled for Thursday, March 22 (invite and registration link below). This is the 2nd in a series of 3 webcasts dedicated to expanding the understanding of the full capabilities of WebCenter. Yes – that might mean that you are not getting the full benefits of the software you already own or the expansion potential via upgrade to the full WebCenter Suite Plus. Tune in on Thursday 10 a.m. PT / 1 p.m. ET.  ++++++++++++++ Want to be a Speaker at Oracle OpenWorld 2012? Oracle Open World planning has already kicked off. We know that it is only March and next October is far in the distance. But planning has already started for Oracle OpenWorld 2012. So if you want to be a speaker and propose your own session for this year's event in San Francisco on September 30th - October 4th, starting thinking now!  The annual OpenWorld Call for Papers is now open until April 9th! All of the details to submit a paper are available here. Of course, the WebCenter team here is interested in sessions including case studies, thought-leadership, customer stories around any of the Oracle WebCenter solutions, but the Call for Papers is open to all Oracle topics. When submitting your topic, be sure to describe what you plan to discuss and the value of the presentation to other attendees. Sell your session, because there will be a lot of competition to be selected.  Bonus News: Speakers for selected sessions receive a complimentary full conference pass! Get your papers in and we'll see you in San Francisco! ~~~~~~~~~~~~~~~~~~~~~~ Webcast Series: Do More with Oracle WebCenter - Expand Beyond Content Management Enable Employees, Partners, and Customers to Do More with Your Content Dear [FIRSTNAME] [LASTNAME],-- Did you know that, in addition to content management, Oracle WebCenter now also includes comprehensive portal, composite application, collaboration, and Web experience management capabilities? Join us for this Webcast and learn how you can provide a new level of user engagement. Learn how Oracle WebCenter: Drives task-specific application data and content to a single screen for executing specific business processes Enables mixed internal and external environments where content can be securely shared and filtered with employees, partners, and customers, based upon role-based security Offers Web experience management, driving contextually relevant, social, and interactive online experiences across multiple channels Provides social features that enable sharing, activity feeds, collaboration, expertise location, and best-practices communities Learn how to do more with Oracle WebCenter. Register now for the Webcast. Register Now Join us for the second Webcast in the series "Do More With Oracle WebCenter". March 22, 2012 10 a.m. PT / 1 p.m. ET Presented by: Michelle Huff Senior Director, WebCenter Product Management, Oracle Greg Utecht Project Manager,IT Operations,TIES Copyright © 2012, Oracle and/or its affiliates. All rights reserved. Contact Us | Legal Notices | Privacy Oracle Corporation - Worldwide Headquarters, 500 Oracle Parkway, OPL - E-mail Services, Redwood Shores, CA 94065, United States

  Read the article

• Database – Beginning with Cloud Database As A Service

  - by Pinal Dave

  I love my weekend projects. Everybody does different activities in their weekend – like traveling, reading or just nothing. Every weekend I try to do something creative and different in the database world. The goal is I learn something new and if I enjoy my learning experience I share with the world. This weekend, I decided to explore Cloud Database As A Service – Morpheus. In my career I have managed many databases in the cloud and I have good experience in managing them. I should highlight that today’s applications use multiple databases from SQL for transactions and analytics, NoSQL for documents, In-Memory for caching to Indexing for search.  Provisioning and deploying these databases often require extensive expertise and time.  Often these databases are also not deployed on the same infrastructure and can create unnecessary latency between the application layer and the databases.  Not to mention the different quality of service based on the infrastructure and the service provider where they are deployed. Moreover, there are additional problems that I have experienced with traditional database setup when hosted in the cloud: Database provisioning & orchestration Slow speed due to hardware issues Poor Monitoring Tools High network latency Now if you have a great software and expert network engineer, you can continuously work on above problems and overcome them. However, not every organization have the luxury to have top notch experts in the field. Now above issues are related to infrastructure, but there are a few more problems which are related to software/application as well. Here are the top three things which can be problems if you do not have application expert: Replication and Clustering Simple provisioning of the hard drive space Automatic Sharding Well, Morpheus looks like a product build by experts who have faced similar situation in the past. The product pretty much addresses all the pain points of developers and database administrators. What is different about Morpheus is that it offers a variety of databases from MySQL, MongoDB, ElasticSearch to Reddis as a service.  Thus users can pick and chose any combination of these databases.  All of them can be provisioned in a matter of minutes with a simple and intuitive point and click user interface.  The Morpheus cloud is built on Solid State Drives (SSD) and is designed for high-speed database transactions.  In addition it offers a direct link to Amazon Web Services to minimize latency between the application layer and the databases. Here are the few steps on how one can get started with Morpheus. Follow along with me.  First go to http://www.gomorpheus.com and register for a new and free account. Step 1: Signup It is very simple to signup for Morpheus. Step 2: Select your database   I use MySQL for my daily routine, so I have selected MySQL. Upon clicking on the big red button to add Instance, it prompted a dialogue of creating a new instance.   Step 3: Create User Now we just have to create a user in our portal which we will use to connect to a database hosted at Morpheus. Click on your database instance and it will bring you to User Screen. Over here you will notice once again a big red button to create a new user. I created a user with my first name.   Step 4: Configure your MySQL client I used MySQL workbench and connected to MySQL instance, which I had created with an IP address and user.   That’s it! You are connecting to MySQL instance. Now you can create your objects just like you would create on your local box. You will have all the features of the Morpheus when you are working with your database. Dashboard While working with Morpheus, I was most impressed with its dashboard. In future blog posts, I will write more about this feature.  Also with Morpheus you use the same process for provisioning and connecting with other databases: MongoDB, ElasticSearch and Reddis. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: MySQL, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL

  Read the article

• mythbuntu 12 - lirc device doesn't appear to even exist

  - by FrustratedWithFormsDesigner

  I'm trying to get a new installation of Mythbuntu working. So far, everything is OK except the remote. The sensor for the remote is on my Hauppauge WinTV HVR 1250. First I tried to run irw to see what was being picked up by the sensor: $ irw connect: No such file or directory Then trying to run lircd gives: $ lircd start$ lircd start lircd: can't open or create /var/run/lirc/lircd.pid I look for any lirc devices and find there are none: $ ls /dev/li* ls: cannot access /dev/li*: No such file or directory Just to be sure, I check in /proc/bus/input/devices, which shows me two powerbuttons (not sure why), kbd and mouse dev, and the audio devs. Nothing for the IR receiver on the tuner card (which I thought was strange because shouldn't the tuner show up here?). $ cat /proc/bus/input/devices I: Bus=0019 Vendor=0000 Product=0001 Version=0000 N: Name="Power Button" P: Phys=PNP0C0C/button/input0 S: Sysfs=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 U: Uniq= H: Handlers=kbd event0 B: PROP=0 B: EV=3 B: KEY=10000000000000 0 I: Bus=0019 Vendor=0000 Product=0001 Version=0000 N: Name="Power Button" P: Phys=LNXPWRBN/button/input0 S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 U: Uniq= H: Handlers=kbd event1 B: PROP=0 B: EV=3 B: KEY=10000000000000 0 I: Bus=0003 Vendor=099a Product=7202 Version=0111 N: Name="Wireless Keyboard/Mouse" P: Phys=usb-0000:00:10.1-2/input0 S: Sysfs=/devices/pci0000:00/0000:00:10.1/usb8/8-2/8-2:1.0/input/input2 U: Uniq= H: Handlers=sysrq kbd event2 B: PROP=0 B: EV=120013 B: KEY=1000000000007 ff9f207ac14057ff febeffdfffefffff fffffffffffffffe B: MSC=10 B: LED=7 I: Bus=0003 Vendor=099a Product=7202 Version=0111 N: Name="Wireless Keyboard/Mouse" P: Phys=usb-0000:00:10.1-2/input1 S: Sysfs=/devices/pci0000:00/0000:00:10.1/usb8/8-2/8-2:1.1/input/input3 U: Uniq= H: Handlers=kbd mouse0 event3 B: PROP=0 B: EV=1f B: KEY=4837fff072ff32d bf54444600000000 70001 20c100b17c000 267bfad9415fed 9e168000004400 10000002 B: REL=143 B: ABS=100000000 B: MSC=10 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Line" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input4 U: Uniq= H: Handlers=event4 B: PROP=0 B: EV=21 B: SW=2000 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Front Mic" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input5 U: Uniq= H: Handlers=event5 B: PROP=0 B: EV=21 B: SW=10 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Rear Mic" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input6 U: Uniq= H: Handlers=event6 B: PROP=0 B: EV=21 B: SW=10 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Front Headphone" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input7 U: Uniq= H: Handlers=event7 B: PROP=0 B: EV=21 B: SW=4 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Line-Out" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input8 U: Uniq= H: Handlers=event8 B: PROP=0 B: EV=21 B: SW=40 According to dmesg, the driver was registered, but it doesn't look like any devices was associated with the driver: $ dmesg | grep irc [ 10.631162] lirc_dev: IR Remote Control driver registered, major 249 So far, I've seen a number of forum pages suggesting that I use some trick to create a link between /dev/lirc and some other device that is the REAL IR sensor, like /dev/event5, but those cases assume that the real device is shown from /proc/bus/input/devices, and I don't see any such device there. Any suggestions on how to fix or further diagnose this?

  Read the article

< Previous Page | 678 679 680 681 682 683 684 685 686 687 688 689  | Next Page >