Search Results

Search found 18907 results on 757 pages for 'computer history'.

Page 683/757 | < Previous Page | 679 680 681 682 683 684 685 686 687 688 689 690  | Next Page >

  • How to Monitor Network in Medium-Sized Company?

    - by Kyle Lowry
    I work at a medium sized company (100+ employees). An issue that has been cropping up is network performance, internet access in particular. We have about 70 or more computers, a mix of Mac OS X and Windows XP & 7 machines. We have several servers (Exchange server, PC file servers, MS SQL, Blackberry, FTP, Mac server, etc). There are four main switches, a SonicWall firewall, and probably a couple routers in the server room with a dozen or so more scattered around the building. The network structure has grown organically over a number of years; and, as far as I know, there really isn't a monitoring solution in place. When we experience network issues (slow connections, dropped packets, and so on), our general solution is to power cycle some hardware or go around to each employee and ask them if they are uploading/downloading any large files. This is really inefficient and time consuming, and it does not allow us to monitor the network, tackling potential problems proactively. I would like to find a solution that would allow me to monitor network usage company-wide in real time, with detail going down to the individual computer, ideally. Given the hodgepodge of equipment and operating systems, what would be the best way to set up some kind of monitoring solution? Hardware, software, restructuring our network architecture?

    Read the article

  • Output current with Teensy++ 2.0 (arduino-based hardware)

    - by omtinez
    I am working on a project with a Teensy++ 2.0 for testing, eventually the goal is to use a Teensy 2.0 (info on both available here) and mount it onto a robot R/C car along with a Raspberry Pi. I have been able to use and test one of the very cheap distance sensors that use ultrasound, which requires very little current. I was trying to power a motor, I don't know exactly what kind of motor but I assume a very low-power one which is what comes with the R/C car cheapo, but nothing is happening. When I plug the motor to GROUND and +5V it runs fine, but when I use GROUND and one of the GPIO pins then nothing happens with the motor. The same GPIO pins were tested to successfully power and run the ultrasound sensor, so the board is fine. My suspicion is that the GPIO pins don't output enough current to power the motor, but my knowledge of electronics is rather scarce (I am a computer scientist, not an electrical engineer). So please forgive me if I am asking something obvious or plain stupid, but does the board not have enough power to power the motor? If so, I could try to use a second power supply that would go straight into the motor and use the GPIO as a gate to turn that power on and off; would such thing work? Is there a better design that could be used?

    Read the article

  • Windows Broken after Deletion of HP_TOOLS partition

    - by beanland
    When I decided to install Ubuntu on my laptop as a dual-boot, I recognized that Windows 7 was using four separate partitions. I (yes, this was stupid) thought the HP_TOOLS partition was probably one I could get rid of, so I deleted it and installed Ubuntu side-by-side Windows using the installation wizard, but now Windows won't progress past the loading screen without the computer automatically restarting. I've had to use Ubuntu exclusively since then. I'm not sure how I can recover it. All of my files seem to still be there--I can mount the other partition and see them, use them, etc--but Windows 7 won't boot. I really have no idea what to do or what to try, or even if I'm at a salvageable point. here's a screenshot of GParted: This makes me suspicious that it wasn't necessarily the removal of my HP_TOOLS partition but the "unknown" status of that 992.50 KiB partition there, sda1. I'm assuming that's the recovery one? How can I get Windows bootable again? I'm sorry, but I'm so unfamiliar with this sort of thing I'm not quite sure where to start.

    Read the article

  • Ubuntu 12.04 VirtualBox on powerful W7 quite slow

    - by wnstnsmth
    I own a Thinkpad T420s with 8GB RAM, 160 GB SSD and a quite fast i7 processor. Summa summarum a very fast computer that works perfectly. Now, I am not very impressed by the performance of my Ubuntu 12.04 virtual machine running on VirtualBox 4.1.18. I assume that Virtual Machines are always a bit slower than the guest system, still I think it should be more performant given the hardware settings I give it: 4096 MB RAM 1 CPU without CPU limitation (I would like to give it more but then it does not seem to work - I am not experienced in this maybe somebody could give me advice on this too) Activated PAE/NX, VT-x/AMD-V and Nested Paging 96 MB Graphics Memory (no 2D or 3D acceleration) ~ 14 GB disk space, currently about 7 GB are used Maybe I misconfigured something, could you give me a hint please? Thanks! Edit: What I mean by slow is that for example switching tabs in the browser (whether FF or Chrome) only goes with a 0.5s delay or something, as well as switching application windows and/or double-clicking applications in the dock to get all open windows.. opening Aptana takes about a minute whereas opening something like Photoshop on the guest system takes 5 seconds

    Read the article

  • Router(s) Issue: DNS quries sporadically fail with multiple computers hooked in

    - by bob-the-destroyer
    Basically, after anywhere from 5-60 minutes, DNS queries fail for a few minutes, then slowly begin to resolve correctly. Then the cycle repeats. This occurs only when more than one computer is on the network. All computers on the network experiences the same sporadic DNS outage at the same time. Wireless or wired, Linux or Windows, fresh OS install or old, browser or ping, same symptoms. Duplicated on 3 routers (not chained together, mind you) and 3 ISP's and 3 separate locations over the past several months. The only common theme is a single 5-yo WIN XP laptop which has been in use on the network throughout all this. There also may be anywhere between 1 - 10 devices hooked up wired or wirelessly at a time. The only reprieve I have from this torture is by using any VPN to an outside source - always smooth sailing. I typically set up any router to a) use WPA2/etc security; b) MAC whitelist; c) UPNP OFF (if available); d) always update firmware when available; e) obtain DNS from ISP automatically; f) set the router to act as DHCP server for the internal network. Adjusting channels has no effect. Any ideas?

    Read the article

  • Recovering data from an external hard drive

    - by CCallaghan
    I have a WD Elements 2GB hard drive (formatted NTFS). I accidentally kicked out the USB cable while writing data to the disk, and now I can't access most of the data. Although this was ostensibly my backup drive, there is a great deal of important material on there which was only on there. I realise how idiotic this makes me. (So, formatting is not an option.) Things I've tried/information I've gathered: Windows Explorer will recognise the drive itself. However, it will not access most directories therein (and will sometimes crash when exploring). I can access all of the directories through the command line, but the dir command will often report that it can't read any files in most of the directories. The situation was similar when I hooked it up to an Ubuntu machine: the file explorer crashed, but I could access directories - but not files in those directories - via terminal commands. Several files I tried to copy out either resulted in an I/O error being reported or resulted in the command line crashing. The Disk Management utility on Windows reports a healthy disk formatted as NTFS and not RAW. It also indicates the correct amount of space used up and its capacity (so it seems that the files are not deleted). I've tried to run chkdsk, but that hangs on Step 2 (checking indexes) at 74%. Step 1 reported no bad sectors. I tried Recuva, but that didn't seem to work (stalled at 0% for half an hour). I should also note that the disk doesn't seem to be spinning smoothly; it seems to be chopping back, like it's reading the same sector over and over again. I noticed this after I kicked out the cable. Any help would be greatly appreciated. Update: It would seem the problem has taken a turn for the worse. The external hard drive now shows up on my computer as a local disk and is not mountable by Linux.

    Read the article

  • How to disable my laptop's defective keyboard?

    - by Kolink
    I have an Alienware M17x R2, and after a couple years of use I started having problems with the keyboard: Intermittently, and without warning or apparent cause (even if I'm not touching the computer), the S key (and more recently the D key) will start firing incessant signals until I hit the offending key. I've been using a USB keyboard, which is conveniently exactly the right size to fit over the built-in keyboard without touching any buttons. However, even as I type the defective keyboard will fire its stream of signals. I have contacted Dell about this, twice in fact. The first time, I was just bluntly told that they don't ship replacement keyboards. The second time I was told that they did, but they were out of stock and they would contact me when they were in stock again. They haven't contacted me since. I can't seem to work out which device to disable in the device manager. Here's a screenshot of what I have: None of the keyboard devices have "Disable" in their context menus, only "Uninstall"... so you'll understand if I'm hesitant to try anything myself. Any advice on how to fix this?

    Read the article

  • Ubuntu Launcher Items Don't Have Correct Environment Vars under NX

    - by ivarley
    I've got an environment variable issue I'm having trouble resolving. I'm running Ubuntu (Karmic, 9.10) and coming in via NX (NoMachine) on a Mac. I've added several environment variables in my .bashrc file, e.g.: export JAVA_HOME=$HOME/dev/tools/Linux/jdk/jdk1.6.0_16/ Sitting at the machine, this environment variable is available on the command line, as well as for apps I launch from the Main Menu. Coming in over NX, however, the environment variable shows up correctly on the command line, but NOT when I launch things via the launcher. As an example, I created a simple shell script called testpath in my home folder: #!/bin/sh echo $PATH && sleep 5 quit I gave it execute privileges: chmod +x testpath And then I created a launcher item in my Main Menu that simply runs: ./testpath When I'm sitting at the computer, this launcher runs and shows all the stuff I put into the $PATH variable in my .bashrc file (e.g. $JAVA_HOME, etc). But when I come in over NX, it shows a totally different value for the $PATH variable, despite the fact that if I launch a terminal window (still in NX), and type export $PATH, it shows up correctly. I assume this has to do with which files are getting loaded by the windowing system over NX, and that it's some other file. But I have no idea how to fix it. For the record, I also have a .profile file with the following in it: # if running bash if [ -n "$BASH_VERSION" ]; then # include .bashrc if it exists if [ -f "$HOME/.bashrc" ]; then . "$HOME/.bashrc" fi fi

    Read the article

  • Could 0x800CCC0E in Outlook be caused by bad wireless connection?

    - by AndrejaKo
    I have a computer connected to a WiFi access point/router/modem. Sometimes, I get page not found errors and similar when opening a browser window, sometimes pings fail and it looks like the router's signal isn't very good. On the other hand, I get around 4 bars of signal strength in windows and graph looks good in Inssider. I also never get dropped connection to the router. My main problem is that I often get errors (such as 0x800CCC0E) in Outlook 2010 that after some searching appear to be connected to bad server connection. I'm using GMail over IMAP and all settings are correct. I didn't have similar errors on my previous router, but I'm not 100% sure that they appeared after switching to current one. It may have worked for some time without errors. There are also around 3000 messages on the server and the size of mailbox is around 12 GiB, which may contribute to the problems. On the other hand, there are at least 24 other networks in the 2.4 GHz range which I'm using and the number may have increased since I switched routers. Should I try solving this by getting a router with stronger signal?

    Read the article

  • Problem running MVC3 app in IIS 7

    - by mjmoore99
    I am having a problem getting a MVC 3 project running in IIS7 on a computer running Windows 7 Home-64 bit. Here is what I did. Installed IIS 7. Accessed the server and got the IIS welcome page. Created a directory named d:\MySite and copied the MVC application to it. (The MVC app is just the standard app that is created when you create a new MVC3 project in visual studio. It just displays a home page and an account logon page. It runs fine inside the Visual Studio development server and I also copied it out to my hosting site and it works fine there) Started IIS management console. Stopped the default site. Added a new site named "MySite" with a physical directory of "d:\Mysite" Changed the application pool named MySite to use .Net Framework 4.0, Integrated pipeline When I access the site in the browser I get a list of the files in the d:\MySite directory. It is as if IIS is not recognizing the contents of d:\MySite as an MVC application. What do I need to do to resolve this?

    Read the article

  • #550 5.1.1 RESOLVER.ADR.ExRecipNotFound; not found ##

    - by gtaylor85
    I've searched serverfault and found this question pop-up quite a bit. Unfortunately others problems aren't exactly like mine, and because I'm a true beginner I wanted some more "specific to me" help. If you don't mind. I just set-up a new computer for a user. Copied over her auto-populate and archive emails. Her email, for the most part, works fine. But when she tries to send anything to [email protected] she gets the #550 5.1.1 error. If she uses the exchange webapp she does not have the issue. I can send email to BSMITH, and so can everyone else. The user, as far as I can tell from the EMC reports, is the only person having emails sent back to them and only from BSMITH. I have googled the crap out of this, and attempted some of the solutions to no avail. I've looked for the bmith account in the disabled accounts and copied and attempted to add "IMCEAEX-_O=CHILD+20STUDY+20CENTER_OU=FIRST+20ADMINISTRATIVE+20GROUP_CN=RECIPIENTS_CN=BSMITH@mydomain.com" as an X500 email. I honestly am just following instructions though and I don't really understand what it is I'm doing. Diagnostic information for administrators: Generating server: FS2.FS1D.local IMCEAEX-_O=CHILD+20STUDY+20CENTER_OU=FIRST+20ADMINISTRATIVE+20GROUP_CN=RECIPIENTS_CN=BSMITH@mydomain.com #550 5.1.1 RESOLVER.ADR.ExRecipNotFound; not found ## BTW I love this site and only found out about it a few weeks ago. My girlfriend now loves the photo.stackexchange. So thanks for such a helpful community.

    Read the article

  • mail server checklist..

    - by Jeff
    currently we ran into some issues with our mail server setup. im preparing a list of actions that we should enforce and use in order to maintain a proper email solution within our company. we have around 80 exchange users, and send mass emails out almost on a monthly bases to 20,000 + customers each time.. the checklist i currently have: 1) mcafee mxlogic 'cloud' anti-spam functionality for incoming message. 2) antivirus on each computer in company 3) antivirus on exchange and DNS servers 4) setup SPF record 5) setup DKIM 6) setup domainkey 7) setup senderID 8) submit spf to microsoft, yahoo, etc. for 'whitelist' purposes. 9) configure size limits for messages in exchange to safe numbers 10) i have 2 outside IPs for my email server, incase one gets blacklisted, switch to the backup. 11) my internet site rests on a different ip than the mail server 12) all mass emails for company sent through 3rd party company (listtrak.com) 13) setup domain alias, media, enews, and bounce for the 3rd party mass mail software. 14) verify the setup using [email protected] 15) configure group policy and our opendns.org account to prevent unwanted actions and website viewing mass emails: 1) schedule them to send different amounts at different times (1,000 at 10am, 1,000 at 4pm, 1,000 10am next day).. 2) setup user prefences, decide what they want to receive ect. ( there interests) 3) send a more steady flow of email, maybe 100 a week with top new products instead of 20,000k every other month.. if anyone has suggestions or additions/subtractions to this checklist they are greatly appreciated. thank you

    Read the article

  • Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

    - by Jeff
    A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

    Read the article

  • Volume is no longer showing in Raid Controller BIOS and in Windows

    - by Gordon
    Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

    Read the article

  • mod_rewrite with AJAX applictions: possible?

    - by MrJackV
    I am trying to run Shell In a Box (link) through another server (the computer running shellinabox is not accessible from the internet) . Ideally I could use ProxyPass in the Apache config to have a reverse proxy. Problem is I can't access the conf file. So I tried using .htaccess and I discover that I cannot use ProxyPass in there. So I tried and used mod_rewrite to do the job. Currently I have the following on the .htaccess file RewriteEngine On RewriteRule ^$ http://10.1.13.236:4200/ [P] However while it displays the title correctly and if I open up the source code I can see there is something in the page, nothing is diplayed on the screen (it remains blank). My suspicion is that there are problems with AJAX and this kind of proxy. What I am trying to accomplish with the mod_rewrite as close as possible behaviour to ProxyPass (Mirorr a website in a subdirectory). Is this possible? Is there some other solution (I tried phproxy and khproxy but neither of them is able to display anything)? Thanks in advance

    Read the article

  • Cancelling Window 7 shutdown diables power button

    - by Jens
    Normally, pressing the power button once initiates a shut-down in Windows 7. If any programs are still running that will not quit (e.g. waiting for a dialogue response), Windows overlays the screen with a dialogue allowing the user to cancel the shut-down. I've just noticed that on two different systems here, using this cancel option disables the shut-down via power button. The power button can still be used to kill the system by holding it for a few seconds, using the Start menu button to shut the PC down still works as well. Steps to reproduce: Open Notepad, type a few characters. Do not save. Press the computer's power button. Wait until the dark screen appears. Press cancel. Press the power button again. Notice how nothing happens. What is the reason for this behaviour, and can it be disabled to always try and shut down the PC when the power button is pressed?

    Read the article

  • File descriptor linked to socket or pipe in proc

    - by primero
    i have a question regarding the file descriptors and their linkage in the proc file system. I've observed that if i list the file descriptors of a certain process from proc ls -la /proc/1234/fd i get the following output: lr-x------ 1 root root 64 Sep 13 07:12 0 -> /dev/null l-wx------ 1 root root 64 Sep 13 07:12 1 -> /dev/null l-wx------ 1 root root 64 Sep 13 07:12 2 -> /dev/null lr-x------ 1 root root 64 Sep 13 07:12 3 -> pipe:[2744159739] l-wx------ 1 root root 64 Sep 13 07:12 4 -> pipe:[2744159739] lrwx------ 1 root root 64 Sep 13 07:12 5 -> socket:[2744160313] lrwx------ 1 root root 64 Sep 13 07:12 6 -> /var/lib/log/some.log I get the meaning of a file descriptor and i understand from my example the file descriptors 0 1 2 and 6, they are tied to physical resources on my computer, and also i guess 5 is connected to some resource on the network(because of the socket), but what i don't understand is the meaning of the numbers in the brackets. Do the point to some property of the resource? Also why are some of the links broken? And lastly as long as I asked a question already :) what is pipe?

    Read the article

  • How to make my Ubuntu an internet gateway for my Android phone

    - by yacine
    I want to use the internet of my school on my Android, the problem is they have a Squid proxy, and many applications on my phone don't use the proxy at all. The obvious solution is to install a transparent proxy on my Android to force all applications to connect through it. The problem is that I need to root the phone to make it work, and I don't want to do it because it's not really my phone and rooting is a little risky- Another solution, which is safer, is to make my computer run as a gateway, so I put my Ubuntu IP in the gateway parameter of the phone. I'm running a small proxy on my ubuntu (cntlm), so I redirect the Android traffic to it. I did it with "iptables" as follows: iptables -t nat -A PREROUTING -s 10.0.1.118 -p tcp -j REDIRECT --to-ports 8888 iptables -t nat -A PREROUTING -s 10.0.1.118 -p udp -j REDIRECT --to-ports 8888 10.0.1.118 is the IP of the phone, 8888 is the port of cntlm (proxy on my PC). Now, on the phone: When I enter www.google.com on the navigator I get nothing (web site not found, error message of Firefox). But, when I enter http://74.125.143.101 (IP of Google) I get an error message from the school proxy (so it worked in some way – my PC redirected the traffic of the phone to the Squid proxy). The error message is : The requested URL could not be retrieved while trying to process the request get / http/1.1 host 74.125.143.101 user-Agent ... ... I think the problem is in the "GET" header,it should be GET 74.125.143.101 HTTP/1.1. But I don't understand what's happening, and I'm a certified CCNA.

    Read the article

  • How to fix Windows 7 when System Recovery Options hangs?

    - by seansand
    The battery power ran out on my HP G60 laptop and it shut down. Even after recharging, Windows 7 will now not start up. After any attempted startup, it bluescreens and takes me to the "Startup Repair (recommended)" / "Start Windows Normally" console screen. "Startup Repair (recommended)" appears to be the right choice, but when I choose it, I get taken to a screen which appears to be System Recovery Options (it's the same wallpaper as the screenshots here: http://www.sevenforums.com/tutorials/668-system-recovery-options.html). However, I just get a cursor with nothing else; no "System Recovery Options" window ever pops up. (A black console screen does pop up for a split-second but too fast to be able to read the text.) The empty screen with cursor hangs indefinitely. System Recovery Options normally runs off of a partition on the laptop hard drive. When I got the laptop, I also created a System Repair Disc (in fact I have more than one) and when I try use any of them; they all result in the same wallpaper and empty screen with lone cursor. Ctrl-Alt-Del does nothing. The computer did not come with a Windows 7 installation disc, so there's no obvious way to reinstall Windows 7. Safe mode does not work; startup fails and I just get sent back to the "Startup Repair (recommended)"/"Start Windows Normally" console screen. "Start in last good state" does not work either, same result as above. Running a memory & hard disk check found no errors. Do I have any options at all? "System Recovery Options" seems to be what I want, but the screen that is supposed to take me to them just hangs.

    Read the article

  • "Windows failed to start" loop with 0xc0000225. No install discs, EasyRE/USB iso hasn't worked

    - by mvidaure
    I've been suffering from this "Windows failed to start" loop with 0xc0000225 for 3 days now and I still can't fix it. The major problem is that I don't have any sort of installation disc. However, I have tried EasyRE via both CD and USB but both result in the same problem.  I try to perform an 'Automated Repair' on my computer and I get in red text "The selected partition is corrupted and could not be accessed or repaired. Please select a different drive to continue." It is also labeled as NO under Active. Since I do not have a the installation discs, I made a USB with a Windows_7_Recovery_Disc  iso (as shown here http://www.sevenforums.com/tutorials/31541-windows-7-usb-dvd-download-tool.html) but it also doesn't work. I get a blue screen that says "RECOVERY You pc needs to be repaired. The application or operating system could not be uploaded because a required file is missing or contains errors... File:\WINDOWS\system32\winload.efi Error code: 0xc0000225 You'll need to use the recovery tools on your installation media. If you don't have any installation media, contact your system administrator or PC manufacturer." Thanks in advance! Miguel

    Read the article

  • Hard drive causing BSOD

    - by JoshIrving
    I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

    Read the article

  • Made a .dmg for a project; user can't open it - "no mountable file systems"

    - by dragonridingsorceress
    Hello, We don't know a great deal about Macs. We had to make an installer, and were told to try a .dmg So we put together version 1, and it seemed to work. We had one application file, which had our icon, and one folder. The user was instructed to drag these into the Applications folder, of which there was the Mac version of a shortcut in the dmg. Then we were told we needed to update files, and assured that we could do so via drag-and-drop. So we did; we dragged them into the folder in the dmg. We tested it (on the computer we were using to edit the dmg) and it seemed to work. So we burnt it onto a disk (along with a windows installer that actually works!). I've just gotten an email from the recipient. She's got a Mac laptop. She inserted the disk, doubleclicked on it, doubleclicked on the .dmg, and got a Warning: no mountable file systems. Screenshot: http://www.flickr.com/photos/97292258@N00/5101670174/ I have the dmg (not on a disk) and am able to open it with no difficulty. How can we get it to work for our recipient?

    Read the article

  • VirtualName-based local development host behind corporate proxy (MAMP)

    - by geerlingguy
    I am behind a corporate proxy server/firewall, and this firewall seems to not be too happy with my idea of local development. On my home computer (Mac/Leopard), I have MAMP running, with a rule in /etc/hosts that directs dev.example.com to 127.0.0.1, and I have a virtualhost set up in the httpd.conf file which works great for me. However, at work, I set up the exact same configuration, but am not able to access dev.example.com, likely due to some address/DNS translation going on via the proxy server. Here are the relevant details from Terminal: $ ping dev.example.com PING dev.example.com (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.025 ms $ host dev.example.com Host dev.example.com not found: 3(NXDOMAIN) I've tried adding dev.example.com to the list of bypass addresses in System Preferences (the 'Bypass proxy settings for these Hosts & Domains' list), but that had no effect. Is there any way I can develop locally using name-based hosts at work? I can access localhost, but can't get to the dev.example.com (or any other custom virtualhosts) here at work, which complicates other matters related to the sites on which I'm working...

    Read the article

  • Can Windows Media Player create playlists based on folder structure?

    - by Chaulky
    Over the years I've carefully molded my digital media collection into a series of folders that make it easy for me to find what I'm looking for. I recently discovered the awesomeness that is streaming video from Windows 7 Media Player to the PS3 so I can watch it on the big screen without all the hassle of hooking the computer up to the TV. The problem is, I totally lose my carefully crafted folder structure and all my videos become one giant mess again... not cool! As a temporary solution, I've created a few playlists for my favorites (Dexter Season 4, Dexter Season 5, Breaking Bad Season 1, etc.). This is a HUGE pain in the a$$. So, is there a way to get Windows Media Player (on Windows 7) to maintain some sort of folder structure based on the location of the actual video files? So if I have my videos sorted into folders by show and season, Media Player will pick that up and let me browse it in the same way. As an alternative answer, I'll accept suggestions for a program that can also stream to PS3 and has this "folder organization" feature.

    Read the article

  • Command prompt cannot find PATH variable

    - by davidXYZ
    Sometimes, my command prompt cannot find the PATH variable. I have this occasional problem at work where when I open command-prompt and run commands like ipconfig or subst, I get an error saying something like 'ipconfig' is not recognized as an internal or external command. When I try this echo %path%, it prints out %path% instead of the PATH value. If I look at my Environment Variables window, the PATH is defined right there but I don't know why CMD can't find it. At this point, I understand why the other commands were not being recognized since their paths are in PATH variable. However, I cannot understand why the PATH variable is not being found. If I restart the computer, everything is back to normal. In a few days, I might have the same experience again. I tried using this answer. It suggested changing a registry value but mine already had the value that was suggested yet it wasn't working. (The restart step at the end would have solved it as usual but that's not the point.) Any suggestions regarding why the PATH variable may become invisible every now and then and how I can prevent it from happening again?

    Read the article

< Previous Page | 679 680 681 682 683 684 685 686 687 688 689 690  | Next Page >