Search Results

Search found 19471 results on 779 pages for 'network troubleshooting'.

Page 693/779 | < Previous Page | 689 690 691 692 693 694 695 696 697 698 699 700  | Next Page >

  • which vista services can be disabled with impunity?

    - by GwenKillerby
    I use Vista on a HP pavilion DV2 laptop. When I look through all the services my laptop starts, it really seems there's way too much of it. I multi boot with XP and 7. Both startup in 40 seconds. Vista takes four minutes. Is there some software that can determine which services I don't need? On 7, there's no propietary HP stuff at all, yet it seems to run fine. Because all these service, there's a LOT of them and some just sit there doing nothing, monitoring for updates I don't really need or want or need to know about the second they're available. my laptop is the only computer i use at home, there's no home network, aside from the modem-router, which is cabled, not wifi. Take for instance Parental controls, and stuff for people with bad eyesight, Tablet PC. I really never use any of that stuff. Hope this question is specific enough. I've looked at the other questions but they didn't answer me. thanks, Gwen.

    Read the article

  • There are currently no logon servers available

    - by Ian Robinson
    I am running a Windows 7 laptop that is joined to my company's domain. When I installed Windows 7, I created an account for myself, joined to the domain, and it had been working quite well even though I'm physically remote most of the time, and not actually on the network. However, today I created a new local user account (non-admin) for my little brother. While he was using it, he decided he wanted to install a program, because his account is not an admin, he was prompted to enter Administrator credentials to allow the program to make changes to his computer. I entered my credentials, and this is the first time I ran into the error message: There are currently no logon servers available to service the logon request. I tried logging off and loggin back in, rebooting, etc etc, and no matter what, every time I try to authenticate as my "normal" domain account - I get that message. I can no longer access my computer as an administrator. I no longer know how to log in to my machine using any other account aside from my little brother's non-admin account. I don't have any other local accounts created, and the default local admin account was never enabled. I'd appreciate any ideas on how I can recover access to my account. Let me know if I can provide any more information. FYI - This is a similar question but not sure any of the answers help me in my case. http://serverfault.com/questions/71632/there-are-currently-no-logon-servers-available-to-service-the-logon-request

    Read the article

  • SQL Server 2008: Getting Login failed for user "Domain\User". Failed to open the explicitly specified database [CLIENT: IP.ADD.RR.ESS]

    - by GodEater
    This is a very similar issue to " SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified database " which unfortunately seems to have gone unsolved. My issue here is subtly different. Firstly the account failing login is not 'NT AUTHORITY\NETWORK SERVICE' - it's an actual domain account. Secondly, there are two machines involved - I gathered from the first question it was a single machine running both the IIS and SQL instances. The application which is trying to connect to the database is an ASP.NET one running on another server (if that makes any different, I'm not sure it does.) The ConnectionString being used in the web.config for the application is : data source=MySQLServer;initial catalog=MyDatabase;integrated security=sspi; And the Application Pool is set to NetworkService for Identity. So - in the web app, I get the following error : Cannot open database "MyDatabase" requested by the login. The login failed. Login failed for user 'MyDomain\WebServerMachineName$' In the SQL Server logs I see : Login failed for user 'MyDomain\WebServerMachineName$'. Reason: Failed to open the explicitly specified database. [CLIENT: Web.Server.IP.Address] Running this bit of SQL against the database in question : USE [MyDatabase] GO SELECT SDP.name AS [User Name], SDP.type_desc AS [User Type], UPPER(SDPS.name) AS [Database Role] FROM sys.database_principals SDP INNER JOIN sys.database_role_members SDRM ON SDP.principal_id=SDRM.member_principal_id INNER JOIN sys.database_principals SDPS ON SDRM.role_principal_id = SDPS.principal_id Gets me this result : MyDomain\WebServerMachineName$ WINDOWS_USER DB_DDLADMIN MyDomain\WebServerMachineName$ WINDOWS_USER DB_DATAREADER MyDomain\WebServerMachineName$ WINDOWS_USER DB_DATAWRITER Which appears to me to indicate I've got the permissions right. Anyone have any idea why it's not working, or how I can narrow the issue down some more?

    Read the article

  • How to create domain or router-level workgroup (dd-wrt micro)

    - by Anthony
    In Windows, is active directory required for using "Domain" instead of "workgroup"? Do I need to register a domain with a DNS provider like godaddy? What I really want to do is set up my home LAN so that everyone connecting to the main router (which is everyone, which is about 30 people) can see each other. I've tried having everyone use the same work group name, still hit or miss. I tried setting the domain name and host name on the router itself, still nothing. I've tried joining the domain name I set instead of work group, and I get an AD error. But ideally, everyone who is connected to the main router should simply just see each other and any shared folders. I've had this problem when I was not the network admin on other large LANs, and I've never been able to figure out why sometimes people disappear or never see each other. I'd really prefer using the native sharing functionality in the OS to setting up an internal FTP or Samba server, etc. Any sure-fire ways to fix this? (maybe an open source clone of AD?) Thanks!

    Read the article

  • EMC VNX iSCSI setup - unsure about SP/port assignment

    - by pauska
    We have a new VNX5300 waiting to get configured, and I need to plan out the network infrastructure before the EMC tech arrives. It has 4x1gbit iSCSI per SP (8 ports in total), and I'd like to get the most out of the performance until we jump over to 10gig iSCSI. From what I can read from the docs - the recommendation is to use only two ports per SP, with 1 active and 1 passive. Why is this? It seems kind of pointless to have quad-port i/o-modules and then recommend to not use more than two of them? Also - I'm a bit unsure about the zoning. The best practices guide state that you should separate each port on each SP from each other on different logical networks. Does this mean that I have to create 4 logical networks to be able to use all 8 ports? It also gives the following example: Does this mean that A0 and B0 should sit on the same physical switch aswell? Won't this make all traffic go on one switch (if both A1 and B1 are passive)? Edit: Another brainpuzzle I don't get it - each host (as in server) should not have more iSCSI bandwidth available than the storage processor. What on earth does this matter? If serverA have 1gbit and serverB have 100mbit, then the resulting bandwith between them is 100mbit. How can this result in some kind of oversubscription? Edit4: Wait, what. Active and passive ports? The VNX runs in a ALUA configuration with asymmetrical active/active.. there shouldn't be any passive ports, only preferred ones..

    Read the article

  • WiFi & GbE Slow while Both Active.

    - by Mark Tomlin
    I'm having a problem with my WiFi network connection when I use my wired GbE connection concurrently on my Laptop. I'm using my WiFi for Internet access, and general web surfing and I'm using my GbE connection to connect to my PlayStation so I can stream media. The WiFi connection is via a Linksys 610N connected to my Cable Modem. Where as the GbE connection is a direct connection from my Ethernet port to the Ethernet port of the PS3 via a Cat-5 cable (no router in between this connection). As soon as I connect the cable from the PS3 to my Ethernet port on my Laptop the WiFi connection slows to a halt, but then allows for a connection to the web as normal but at much slower speeds for the things like BitTorrent that stops completely. It seems to me that Windows can't handle both connections at once. It will have both active but it can only accept and send packets on one device at one time. I can get WiFi connections to work to go to websites and the like, but once I use my GbE connection to share media between my Laptop and my PS3 the Wifi connection dies out and I no longer have access to the internet. I setup my connection on the PS3 and the Laptop following the insturctions posted here: http://forums.finalgear.com/problems/s14e01-ps3-size-problem-40642/#post1188132 And the following is the results of my ipconfig. Windows IP Configuration Host Name . . . . . . . . . . . . : dygear Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter WiFi: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/Wireless 3945ABG Network Connection Physical Address. . . . . . . . . : 00-19-**-**-**-** Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.111 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 167.206.254.2 167.206.254.1 Lease Obtained. . . . . . . . . . : Wednesday, May 19, 2010 08:55:30 Lease Expires . . . . . . . . . . : Thursday, May 20, 2010 08:55:30 Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-16-**-**-**-** Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.1.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Any ideas?

    Read the article

  • How to set up a easy-to-use proxy for the whole system with WinXP client and server?

    - by Pekka
    I am working together intensively with a colleague on the Canary Islands. We speak through live messenger and work together using a RDP software. She has frequent problems with connections to certain big-name and small-name sites (amongst others live.com, google.com, gmx.de) very likely to be caused by the spanish provider (the connections simply time out, this has been going on for weeks already). I have been thinking about setting up my computer as a proxy to make these connections work. I have a DSL connection and am behind a NAT capable router that I control. Does anybody know a simple, "one-click" way to transport ALL network traffic through a remote proxy? Without having to set proxy settings for each application that uses the internet? VPN is not an option, because I am behind a firewall that supports protocol 47 and such, but I have never succeeded in getting an incoming VPN connection to work. I can however redirect normal traffic using NAT. A VPN solution that does not need strange protocols would also be an option.

    Read the article

  • Getting rid of your server in a small business environment

    - by andygeers
    In a small business environment, is it still necessary to have a central server? Speaking for my own company (a small charity with about 12 employees) we use our server (Windows Server 2003) for the following: Email via Microsoft Exchange Central storage Acting as a print server User authentication / Active Directory There are significant costs associated with running a server like this: Electricity, first for the server itself then for the air conditioning required (this thing pumps out a lot of heat) Noise (of which there is a lot) IT support bills (both Windows Server and Exchange are pretty complicated, and there are many ways they can go wrong) I've found ways to replace many of these functions with cheaper (better?) alternatives: Google Apps / GMail is a clear win for us: we have so many spam related problems it's not even funny, and Outlook is dog slow on our aging computers You can buy networked storage devices with built in print servers, such as the Netgear ReadyNAS™ RND4210 that would allow us to store/share all of our documents, and allow us to access printers over the network The only thing that I can't figure out how to do away with is the authentication side of things - it seems to me that if we got rid of our server, you'd essentially have a bunch of independent PCs that had no shared pool of user accounts / no central administrator. Is that right? Does that matter? Am I missing any other good reasons to keep a central server? Does anybody know of any good, cost-effective ways of achieving the same end but without the expensive central server?

    Read the article

  • SSH session becomes unresponsive when logged into Ubuntu Server virtual machine using VirtualBox

    - by nickbart
    Hi everyone, I'm really at my wits end here, so I'm hoping someone here can help me. I have a virtual machine running Ubuntu Server 9.10. It's just a small development environment so I can keep my code separate from the test and production environments. I am running it through VirtualBox 3.1.6 on a laptop running Ubuntu Desktop 9.10. I have it set up with a bridged network connection and it is bridged to my laptop's wireless adapter. We have no wired connections in this office. I boot up the VM and everything is fine. I can SSH into it using gnome-terminal and for a while everything is Kosher. Then seemingly randomly, the SSH terminal session with hang. No error message, nothing; it just becomes unresponsive. If I go to the VirtualBox terminal I find the VM itself is perfectly fine. It can ping and I can SSH out with it. If I restart the networking on the VM the SSH session in my gnome-terminal will most of the time become responsive again. Here's an interesting point, the SSH session will sometimes die right in the middle of me typing something (this points to it not being an idle session issue) and if I go to the VirtualBox terminal and restart the networking and then return to my gnome-terminal SSH session I find that it will come back to life and what I typed when the session hung originally will magically type itself in to the buffer. So, my input is getting stored somewhere and just can't make its way to the VM until the networking on the VM is restarted. I've tried different versions of VirtualBox and used vmdk images and vdi images and nothing seems to work. I can't tell if the problem is with my laptop, VirtualBox, or the Ubuntu Server VDI. Is there anyway to debug this issue? Or has anyone out there seen anything similar? Your help is much appreciated. Nick

    Read the article

  • mount.nfs: access denied by server while mounting (Kerberos authentication)

    - by Nick
    There's plenty of references to this error on Goggle, and even a question here with the same title, but it seems that "access denied by server while mounting" is a catch-all error. I've tried suggestions that others have used to fix this problem, but they did not work in my case. I'm trying to set-up a Kerberos-based NFS file server with shared homes for a Linux network. I'm using Ubuntu 11.04 Servers and clients. When trying to mount a share using: mount 192.168.1.115:/export/home/ /media/tmp I get: mount.nfs: access denied by server while mounting 192.168.1.115:/export/home/ This is the same if I mount it from a client machine or from the server itself. On the server, in /var/log/syslog I get: Aug 25 06:22:37 nfs mountd[1580]: authenticated mount request from 192.168.1.115:835 for /export/home (/export/home) Aug 25 06:22:37 nfs mountd[1580]: authenticated unmount request from 192.168.1.115:766 for /export/home (/export/home) Which is odd, since it says it's authenticated the request, not denying it. /etc/exports: /export *(rw,fsid=0,crossmnt,insecure,async,no_subtree_check,sec=krb5p:krb5i:krb5) /export/home *(rw,insecure,async,no_subtree_check,sec=krb5p:krb5i:krb5) On client: me@dt1:/$ rpcinfo -p 192.168.1.115 program vers proto port 100000 2 tcp 111 portmapper 100024 1 udp 37320 status 100024 1 tcp 48460 status 100003 2 tcp 2049 nfs 100003 3 tcp 2049 nfs 100003 4 tcp 2049 nfs 100227 2 tcp 2049 100227 3 tcp 2049 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 100003 4 udp 2049 nfs 100227 2 udp 2049 100227 3 udp 2049 100021 1 udp 58625 nlockmgr 100021 3 udp 58625 nlockmgr 100021 4 udp 58625 nlockmgr 100021 1 tcp 49616 nlockmgr 100021 3 tcp 49616 nlockmgr 100021 4 tcp 49616 nlockmgr 100005 1 udp 45627 mountd 100005 1 tcp 60265 mountd 100005 2 udp 45627 mountd 100005 2 tcp 60265 mountd 100005 3 udp 45627 mountd 100005 3 tcp 60265 mountd Any suggestions I could try?

    Read the article

  • VMware NAS/iSCSI recommendations - smallish organization

    - by Bubnoff
    I have two VMware servers - ESX + ESXi. Two backup NAS boxes. The current NAS boxes are low-cost and unsuitable for running VMs from. Support NFS only. Slow. My plan is to have a dedicated iSCSI/NAS for storing and running VMs. Two additional low-cost boxes for backup. I'm looking for advice regarding 2 things really: Recommendations as far as VMware architecture/design for a smaller organization. Less than 20 Virtual Machines. 2 servers + 2 x 1.5 terabyte backup NAS boxes. A good NAS/iSCSI box with your recommendation on RAID config ...I would go with 6 or better. I'm trying to design an installation that is both fast and reliable/redundant. If you have any experiences to share or your current configuration including network design ( switches, fiber ...etc ), I will be enormously thankful. I'm not married to this idea, so if you have a design not using iSCSI NAS boxes ...let er rip. Cost? Can we stay around $5,000 ( on top of already stated components )? Links to info are welcome also. Thanks for reading! Bubnoff

    Read the article

  • Weirdly high ping on direct ethernet connection?

    - by Antriel
    I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms. I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms. I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN). Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't help. I tested it in the safe mode with networking, same problem there. It slows down our client-server based programs and I have no idea what's causing it. All I could google up was that disabling Interrupt Moderation would help, it didn't though. Anyone had similar problems? tl;nr: Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.

    Read the article

  • Moving server room to another part of the building

    - by PHLiGHT
    This question is a bit different than the typical we are moving our server room to an off site location or we are moving the whole office to a new building. Management wants to add some more office space and to do so they want to move the server room to another location. The server room has Verizon smart jacks, a few servers, PBX and all the office network drops go into this room. I'm going to go over there to scout out an alternate location for the equipment because that is still TBD. This sounds like quite a pain since the Verizon equipment for our MPLS will need to be moved (never done that) and the office jacks will need to be re-run. How do you handle the jacks? I was thinking of keeping them in the same location and having new wall plates put in with half the ports going to the current location and the other half to the new location. Or do you think that 40 drops could just be done over the weekend so the old stuff would be ripped out and replaced with the new? Currently the wiring is a mess so this could be a blessing in the long run.

    Read the article

  • wireless router - configuring for low-latency, high traffic environment

    - by Mark C
    Hey all, I have a few questions about configuring a router to achieve low-latency, high speed throughput on a local area network that is not connected to the internet. I've read up on some stuff, but thought I would solicit some opinions here on what I've found and what I want to know.... Turn off SSID broadcast - it produces extraneous packets that all clients receive and reply (?) to. Not a huge deal, but it may help a bit. Mixed-mode off - I should attempt to have all devices using the same standard (e.g. 802.11n) and turn mixed-mode off. Any thoughts on security? Does having WEP or any of the WPA variants actually increase latency? Nothing super secure is going over this LAN so if turning security off made things better, that'd be cool. Any other thoughts or things to focus on to create the low latency environment I'm trying to go for would be great. Links to webpages and papers are also cool. I'm open to go through a bunch of stuff. Thanks in advance!

    Read the article

  • High latency due to non-presence of a transit provider in my country

    - by nixnotwin
    My ISP, a state owned incumbent, buys bandwidth from different transit providers. Whenever it buys transits it announces only a specific prefix (in most cases a hitherto unused) through the new transit AS. For e.g. if it runs out of bandwidth, it buys bandwidth from a new transit and announces a new prefix through it, while the same prefix is not announced (or announced with lowest metrics, so that the routes are very rarely used) via the old transits which continue to provide bandwidth to it. I am a business customer, so I have a fiber based link to the ISP and a tiny subnet is given to me. The subnet which is provide to me is part of a prefix which is announced by the AS of a transit who, it seems, do not have a presence in my country. So when I do a trace the packets, when they leave my ISP's AS, they take about 275ms to reach the transit providers core router, which is located in USA (half the world away). Also for upstream traffic my ISP uses a transit provider (tier 1) who has a presence in my country. But the return path is always through the transit which is in USA. So, average latency is 400ms. All the users of other ISPs in my country discover my subnet via USA. Even the traffic from neighboring countries, from Europe (which is much nearer) follows the path via USA. Sites using CDNs also resolve to ips in USA. I have informed the ISP NOC about the issue and I have asked them to provide an ip subnet belonging to a prefix announced by a local transit (preferably a tier 1 transit provider) and I am waiting for a reply. My question: Is it a serious issue that I must follow up to get it resolved? When I compared the latency on other providers in my country, it is, in most cases, less than half of my ISPs latency. Why my ISP doesn't announce all its prefixes to all of its transit providers, so that the packets can take efficient and nearest routes to reach prefixes that originate within its network?

    Read the article

  • How to prevent asymmetric routing with multiple eBGP routers?

    - by Andy Shinn
    I have 2 routers announcing a /22 subnet to different providers (one providers connects to each of the 2 routers). I have split the /22 in two /23 to announce one /23 on each of the routers plus the /22 (the providers will take the more specific route). This allows me to fail over and keep traffic inside the /23 in and out the same provider. What are other ways in which I could announce just the /22 with both routers and have packets from servers on the network behind the routers go back out the same router in which they came in from? EDIT: The main problem I come across, which end users and clients complain about the most, is that the least hop route is sometimes not the "optimal" route. In my case, I know that Provider B may have better latency to X nation. But when packets come in from provider B, they may go out Provider A or provider B. The reverse is also true. If I send a packet to X nation out provider A, even though it may have more hops back, the packet will likely come in from Provider B (which may have higher latency, packet loss, etc. to this nation)

    Read the article

  • overriding default scheduler for blkio requests in cgroups

    - by Aamir Mushtaq
    I am trying to optimize a set of servers that have to reside on single machine. i.e. i can have multiple application server, a DB server and of course a samba server as well in same instance. Now I was looking into several optimizing options available to me. In my quest, i did my tuning of the network stack. coming to the CPU, MEMORY and the BLKIO tweaks, i am using CGROUPS. The problem i am facing is that for enhanced performance in the nature of the applications that i am running, the CFQ Scheduler that is implemented for the BLKIO subsystem is not optimal. I was looking more for a Deadline Scheduler because that will serve my purpose well. My question is whether it is possible for us to change the scheduler in the kernel compilation itself for the BLKIO to Deadline and it will reflect in my usage of [CGROUP hierarchies][3]? Since when running the service cgconf, a new fs is mounted and i dont want it to revert to CFQ scheduler. I also welcome any suggestions that will enable me to have more control over my resources.

    Read the article

  • Cisco BVI: Claiming IP addresses

    - by cjavapro
    I would like to make sure I understand this correctly. Given a Cisco ISO router that is set up with a BVI (a variation of a bridge route).. and the following layout "ISP router" \ "Network switch" # nothing special here. | \ | \ | \ | \ "Router 1 with NAT" "Router 2 with BVI" If I understand correctly.. the outside of a BVI will only respond to IP addresses that have already been claimed on the inside of the BVI... example subnet is 123.123.123.??? and servers inside the BVI on 123.123.123.10 and 123.123.123.11, and the NAT router is holding a public IP address of 123.123.123.50. If a connection comes in to 123.123.123.10 it will be received by router 2 but if it is received on 123.123.123.50, it will be received by router 1 and not received by router 2. and if a connection comes in to 123.123.123.90 (does not exist) it will not be received by either router. Am I correct? Is it true that the BVI router will not even receive packets to IP addresses that it does not see as existing on the inside?

    Read the article

  • Transfering Files to server IP and port

    - by Mason
    I need to transfer files from my local computer on windows 7 to a server running linux. I access the server with putty through ssh at a specific IPv4 address and port number. I've attempted using the pscp command from my local computer but was denied access by the server. "Fatal: Network error: Connection refused" c:>pscp test.csv userid@**IPv4_Addres***:Port# /path/destination_file_name. Either the server blocks all pscp attempts from unauthorized users (most likely my laptop included) or I used the command incorrectly. If you have experience using this command, where exactly will the file get transfered to, I'm assuming that the path destination starts at my home directory in the server. Also if you have any other alternative methods of transfering the files let me know. Update 1 I have also tried using WinSCP however I got permission denied for that as well, it looks like the server will not let me upload or save files. Solved I had a complete lapse of memory and forgot about sudo (spent too much time with scripts the last 2 months), so I was able to change the permissions to allow external editing. Thanks for all the help guys!

    Read the article

  • Access node.js local server though mobile via same shared wifi

    - by laggingreflex
    EDIT: I was stuck in this situation before but then it was Apache-related But this time I'm using NodeJS, so the old answer doesn't help. I'm running apache a NodeJS webserver (on port 80) on Windows 7. I want to access the webserver through my mobile which shares the wifi router with my pc locally. http://localhost works from PC. But I can't access http://192.168.1.4 from either my phone or even my computer. ipconfig /all on my computer lists my ip address as 192.168.1.4 Wireless LAN adapter Wireless Network Connection: IPv4 Address. . . . . . . . . . . : 192.168.1.4(Preferred) I can ping my phone's (internal) ip address [192.168.1.5] from PC and vice-versa, I can ping my PC [192.168.1.4] from my phone. So why can't I access http://192.168.1.4 from my phone? (or PC) Firewall is off.

    Read the article

  • Slow browsing through IE on Windows Server 2012

    - by Volodymyr
    We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

    Read the article

  • virtual machines, dual booting and data disks on SSD

    - by stevemarvell
    This is in planning, so if I've got the strategy wrong, please let me know. There are multiple questions here, but I think they all degenerate to the same answers. The hardware is a laptop with a single SSD. I'm trying to not lose the performance of the SSD. I plan a native dual booting Windows (plus cygwin) and Linux machine which is my BYOD and represents the development environment. I keep the codebase on a shared partition (though sometimes this is an external thunderbolt SSD) which can be natively "mounted" by whichever OS is in operation. I boot into one or the other environments depending on the task in hand. Sometime I have to develop with windows tools, but generally, Linux is my preferred development environment. It would be ideal if I could VM the other OS and run either in either. I'm going to assume, because I've not found a sensible VM based solution, that I have get samba involved to share the code partition between VMs. Is this going to blow my SSD performance in the VM? The client also supplies me with a VM for the target environment, usually linux. This is not often suited to development and is used for testing only. I normally keep two copies of this, one as a sandbox and one which I deploy to using the client's preferred method. I keep these VM snapshots on the shared partition. The latter is interacted with over the network and so has no disk sharing requirements. However, it would be useful for the sandbox to be able to "mount" the code base from the natively running OS. Is this samba or nfs again, depending on the native OS? Am I missing a trick which allows this to all work smoothly with all four environments running at once without loosing the SSD performance?

    Read the article

  • EventID 1058 Code 5, Sysvol is subdir of Sysvol - how to fix?

    - by nulliusinverba
    I have been trying to resolve this error, like many others: The processing of Group Policy failed. Windows attempted to read the file \domain.local\SysVol\domain.local\Policies{3EF90CE1-6908-44EC-A750-F0BA70548600}\gpt.ini from a domain controller and was not successful. Group Policy settings may not be applied until this event is resolved. This issue may be transient and could be caused by one or more of the following: a) Name Resolution/Network Connectivity to the current domain controller. b) File Replication Service Latency (a file created on another domain controller has not replicated to the current domain controller). c) The Distributed File System (DFS) client has been disabled. Error code: 5 = Access Denied. The incredibly helpful post is this one (http://www.experts-exchange.com/OS/Microsoft_Operating_Systems/Server/2003_Server/A_1073-Diagnosing-and-repairing-Events-1030-and-1058.html). Quoting from this post: HERE IS A LIST OF POTENTIAL PROBLEMS THAT CAN LEAD TO 1030 AND 1058 EVENT ERRORS: --Sometimes the permissions of the file folders that contain Group policies (the Sysvol folder) can be corrupted. --Sometimes you have problems with NetBIOS: --Sometimes the GPO itself is corrupt, or you have a partial set of data for that GPO. --Sometimes you may have problems with File Replication Services, which almost always indicates a problem with DNS --Sysvol may be a subfolder of itself: Sysvol/Sysvol I have the problem listed where sysvol is a subfolder of sysvol. The directory structure is: -sysvol -domain -staging -staging areas -sysvol (shared as "\\server\sysvol") -domain.local -ClientAgent -Policies -scripts Interestingly, the second sysvol folder is the one that is shared as "\server\sysvol". This makes me confident this is the issue with the permissions and error code 5. Also interestingly, my server 2008 R2 servers can see it fine - my server 2008 servers cannot, and get the error. This is consistent across all my servers. This latter fact makes me uncertain what I need to do to fix this up. Do I, e.g., simply move the shared sysvol folder up a level to replace the non-shared one? Any help greatly appreciated. Cheers, Tim.

    Read the article

  • netlogon errors

    - by rorr
    I have two instances of mssql 2005 and am using CA XOSoft replication. The master is a failover cluster and the replica is a standalone server. They are all running Server 2003 sp2 x64. Same patch levels on all servers. This setup has worked great for several months until we recently restricted the RPC ports on both nodes of the master(5000 - 6000 using rpccfg.exe). We have to implement egress filtering, thus the limiting of the ports. We began receiving login errors for sql windows authentication and NETLOGON Event ID: 5719: This computer was not able to set up a secure session with a domain controller in domain due to the following: Not enough storage is available to process this command. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. We also see group policies failing to update and cluster file shares go offline at the same time. The RPC ports were set back to default when we started seeing these problems and the servers rebooted, but the problems persist. The domain controllers are not showing any errors. Running dcdiag and netdiag shows everything is fine. We have noticed that the XOSoft service ws_rep.exe is using a lot of handles(8 - 9k), about the same number that sqlserver is using. As soon as xosoft replication is stopped the login errors cease and everything functions correctly. I have opened a ticket with CA for XOSoft, but I'm not sure that the problem is actually xosoft, but that it is the one bringing the problem to light. I'm looking for tips on debugging RPC problems. Specifically on limiting the ports and then reverting the changes.

    Read the article

  • Sync desktop Mac environment to laptop

    - by Andrew Vit
    I spend the majority of my time working at my desktop Mac, which I have configured for my web development environment. My spouse has a MacBook for casual use, and I occasionally steal it back when I need to work off-site, or when travelling. The question is how to best synchronize the two so I can switch between them more readily. I've solved a few obvious things by using online services: Email is hosted on IMAP. Working files are in Dropbox. Source code is managed in git. However, the following are things I always miss when jumping on the laptop: Installed Applications (current versions) Installed libraries & utilities (/usr/local) Apache VirtualHosts & other configurations (/etc) Disk image files for VMs My current method is to connect the MacBook via Firewire target mode and rsync the /Users/me home directory, and then cherry-pick the other items I need from Applications, /etc and /usr/local. The problem with this method is that it can be very time consuming due to things like my virtual machine image files, cached emails, etc. How can I make this faster & easier? Can you recommend a solution for configuration management (so I can repeatably install & configure the same software on both), or synchronization (so I can bring the MacBook up to date nightly, over our home network)?

    Read the article

< Previous Page | 689 690 691 692 693 694 695 696 697 698 699 700  | Next Page >