Search Results

Search found 21524 results on 861 pages for 'multiple matches'.

Page 701/861 | < Previous Page | 697 698 699 700 701 702 703 704 705 706 707 708  | Next Page >

• apache 2.4 redirect within virtualhost

  - by user129545

  I have a couple http (port 80) vhosts that I want to redirect to http if an https request is made to them. Apparently some things have changed with Apache 2.4 (NameVirtualHost not used like it was in the past, etc). Apache 2.4 on centos 5.5, This is all using a single ip for all vhosts below, I don't have multiple ip's on this box, my /usr/local/apache2/conf/extra/httpd-vhosts.conf : # <VirtualHost www.dom1.com:80> ServerName www.dom1.com ServerAlias dom1.com DocumentRoot /usr/local/apache2/htdocs/dom1/wordpress </VirtualHost> <VirtualHost webmail.dom2.com:443> ServerName webmail.dom2.com DocumentRoot /usr/local/apache2/htdocs/webmail SSLEngine On SSLCertificateFile /usr/local/apache2/webmail.crt SSLCertificateKeyFile /usr/local/apache2/webmail.key </VirtualHost> # my /usr/local/apache2/conf/extra/httpd-ssl.conf, # Listen 443 SSLPassPhraseDialog builtin SSLSessionCache shmcb:/var/cache/mod_ssl/scache(512000) SSLSessionCacheTimeout 300 Mutex default SSLRandomSeed startup file:/dev/urandom 512 SSLRandomSeed connect builtin SSLCryptoDevice builtin # webmail.dom2.com works fine. Problem is I can connect to https://www.dom1.com, and it serves up the content from webmail.dom2.com. I want any https requests for www.dom1.com on port 443 to simply redirect to http://www.dom1.com on port 80. Thanks

  Read the article

• KVM guest VLAN aware problems

  - by baraka

  Hi, We are using Centos 5.5. as KVM host. It has two nics. One for management and the other one for services. As we have services in multiple vlans this nic is configured as a 802.1Q trunk. Any VM must be able to have access to any vlan, so host trunk interface is bridged to its tap interface and vlan is configured inside VM. Everything works fine while there is not heavy traffic. I can not find any log on guest or host, but, after some certain sustained big file transfer (about 6Gb) bridging stop working. Other guest on the same host continue working without problems. tcpdump on bridge interface is Ok, but on guest tap inferface I can see only outgoing traffic. Restarting bridge or rejoining tap interface doesn't provide any clue. Rebooting guest turns on bridge again. Bridge configuration is minimal: just addbr and addif (no stp). Any idea welcome!

  Read the article

• ubuntu ssh does not connect

  - by bocca

  SSH won't be able to establish a connection to our server Here's the output of ssh -vvv: ssh -v -v -v 11.11.11.11 OpenSSH_5.1p1 Debian-6ubuntu2, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 11.11.11.11 [11.11.11.11] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type -1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.1p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-cbc hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 133/256 debug2: bits set: 486/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: filename /root/.ssh/known_hosts debug3: check_host_in_hostfile: match line 1 debug1: Host '11.11.11.11' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:1 debug2: bits set: 497/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /root/.ssh/identity ((nil)) debug2: key: /root/.ssh/id_rsa ((nil)) debug2: key: /root/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug3: no such identity: /root/.ssh/identity debug1: Trying private key: /root/.ssh/id_rsa debug3: no such identity: /root/.ssh/id_rsa debug1: Trying private key: /root/.ssh/id_dsa debug3: no such identity: /root/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 57 padlen 7 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug3: tty_make_modes: ospeed 38400 debug3: tty_make_modes: ispeed 38400 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env SSH_AGENT_PID debug3: Ignored env SHELL debug3: Ignored env TERM debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GTK_RC_FILES debug3: Ignored env WINDOWID debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env GNOME_KEYRING_SOCKET debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env MAIL debug3: Ignored env PATH debug3: Ignored env DESKTOP_SESSION debug3: Ignored env PWD debug3: Ignored env GDM_KEYBOARD_LAYOUT debug3: Ignored env GNOME_KEYRING_PID debug1: Sending env LANG = en_CA.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env GDM_LANG debug3: Ignored env GDMSESSION debug3: Ignored env HISTCONTROL debug3: Ignored env SPEECHD_PORT debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env XDG_DATA_DIRS debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env DISPLAY debug3: Ignored env LESSCLOSE debug3: Ignored env XAUTHORITY debug3: Ignored env COLORTERM debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_confirm: type 99 id 0 debug2: shell request accepted on channel 0

  Read the article

• Unable to ping domain.local, but can ping server.domain.local

  - by Force Flow

  I have a single windows 2008 server running active directory, group policy, and DNS. DHCP is running from the firewall (this is because there are multiple branch locations, and each location has its own firewall supplying DHCP. But, for this problem, the server and workstation are at the same location). On an XP workstation, if I try to visit \\domain.local or ping domain.local, the workstation can't find it. A ping returns Ping request could not find host domain.local. If I try to visit \\server or \\server.domain.local or ping server or server.domain.local, I'm able to connect normally. If I ping or visit domain.local on the server, I'm able to connect normally. A-Records are in place in the DNS service for server, domain.local, and server.domain.local. A reverse lookup zone also is enabled and PTR records are in place. If I wait 20-30 minutes, I am eventually able to ping and visit domain.local--but, when attempting to ping, it takes 30 second to return an IP address. I am also unable to join a new workstation to the domain during this wait period. If I try, the error message returned is "network path not found". Is there something I'm missing?

  Read the article

• Xvnc4 started from xinetd only displays empty gray X screen

  - by scott8035

  I'm attempting to setup an Ubuntu 10.10 box so that anyone can connect to port 5900 and be greeted by the gdm login manager. To do so, I added a vnc entry in /etc/services and I am starting Xvnc4 using this xinetd config file: service vnc { protocol = tcp socket_type = stream wait = no user = nobody server = /usr/bin/Xvnc server_args = -geometry 1000x700 -depth 24 -broadcast -inetd -once -securitytypes None } This kind of works...I can start multiple sessions all to port 5900, and I get an X screen. The problem is that I only get an empty, gray X screen with no applications started. I know when you run vncserver from the command line it will look to your ~/.vnc/ directory for your passwd and xstartup files, and I think what I want to do is put "gnome-session" into the xstart file. However, which xstartup file? The running user is "nobody" who obviously doesn't have a ~/.vnc/ directory. I tried a /root/.vnc/xstartup file and a ~scott/.vnc/xstartup file and it doesn't look like they were even read. I changed the xinetd vnc service so that it would "strace" Xvnc4. I looked thru all the "open" lines and didn't get a clue as to what file it was trying to read for xstart. Can anyone help? I just want a terminal server where the user is presented with a gdm login screen.

  Read the article

• ESXi - change to thin - virtual disk filesize is the same

  - by sven

  running ESXi 5.5 here with a datastore on a single SSD. Now, I thought about changing to thin disks from thick and found that I could use a tool on the ESXi host to do that. However, the file size of the new created virtual disk is not changing. I run: vmkfstools -i loader.vmdk -d 'thin' thinloader.vmdk Destination disk format: VMFS thin-provisioned Cloning disk 'loader.vmdk'... Clone: 100% done. After that I compared the virtual disksizes: ls -la *.vmdk -rw------- 1 root root 32212254720 Jun 10 08:25 loader-flat.vmdk -rw------- 1 root root 467 May 21 17:04 loader.vmdk -rw------- 1 root root 32212254720 Jun 10 08:27 thinloader-flat.vmdk -rw------- 1 root root 520 Jun 10 08:33 thinloader.vmdk Stats on the original file: stat loader.vmdk File: loader.vmdk Size: 467 Blocks: 0 IO Block: 131072 regular file Device: 8bf64d175e27544ch/10085333178302026828d Inode: 419443780 Links: 1 Access: (0600/-rw-------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-01-25 10:17:34.000000000 Modify: 2014-05-21 17:04:06.000000000 Change: 2014-05-21 17:04:06.000000000 and on the thin file: stat thinloader.vmdk File: thinloader.vmdk Size: 520 Blocks: 0 IO Block: 131072 regular file Device: 8bf64d175e27544ch/10085333178302026828d Inode: 432026692 Links: 1 Access: (0600/-rw-------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-06-10 08:27:45.000000000 Modify: 2014-06-10 08:33:30.000000000 Change: 2014-06-10 08:33:30.000000000 Anyone an idea why the disk is not providing any more space (tried with multiple VM's already - all the same)? Also, I have noticed that the newly created file "autoappend" "-flat" to the disk ... Thanks Sven Update - diff of the vmdk config* --- loader.vmdk +++ thinloader.vmdk @@ -7,15 +7,17 @@ createType="vmfs" -RW 62914560 VMFS "loader-flat.vmdk" +RW 62914560 VMFS "thinloader-flat.vmdk" ddb.adapterType = "lsilogic" +ddb.deletable = "true" ddb.geometry.cylinders = "3916" ddb.geometry.heads = "255" ddb.geometry.sectors = "63" ddb.longContentID = "6d95855805dfa0079327dfee29b48dca" -ddb.uuid = "60 00 C2 98 d5 7d 17 bf-ac 54 70 b1 2d 39 43 d5" +ddb.thinProvisioned = "1" +ddb.uuid = "60 00 C2 93 c4 13 6c cf-bb 7b 34 c9 2c b4 dc 1e" ddb.virtualHWVersion = "8"

  Read the article

• Best practice for Exchange 2010 HA topology considering 6 x Exchange licenses and TMG 2010

  - by MadBoy

  What would be best topology considering that: 6 x Exchange 2010 Standard Licenses 2 x Separate locations that are supposed to support redundancy in case of link problems 4 x Forefront TMG 2010 with Forefront Security and Forefront Protection/Security Multiple locations worldwide using those Exchange. Most locations will be connected with VPN Tunnel (the ones hosting Exchange for sure). I was thinking something like this: Location MAIN (about 70-100 people): 2x TMG 2010 in NLB 1x Exchange 2010 CAS/HUB Role 2x Exchange 2010 Mailbox Role (Active + Passive) Location SUPPORT (about 20 people): 2x TMG 2010 in NLB 1x Exchange 2010 CAS/HUB Role 2x Exchange 2010 Mailbox Role (Active + Passive) Management wants to make sure that in case of problems in main location (power failure, link loss etc) second location can support all traffic from around the world and vice-versa. We have 6-7 locations and more comming up (not big ones but like 10+ people per each location). I do know that CAS/HUB is single point of failure (and no NLB), but i simply lack more licenses to do some redundancy on that. What do you think about this approach? What would be better approach according to you?

  Read the article

• Cannot 301 redirect with IIS URL Rewrite Module

  - by Justin

  I am trying to troubleshoot my issue with the URL Rewrite Module on IIS 7. I migrated a Wordpress blog over to BlogEngine.net. There were only about 5 entries that I wanted to use 301 redirects to the new blog, so I wanted to simply create 5 exact match redirect rules using the rewrite module. For some reason the exact match rule never seems to take effect, I always get a 404 error when the original url is navigated to. I verified that my exact match pattern matched the existing backlinks and it does. I then tried a simple test and got the same behavior, no redirection. I created a page, test.html, on my site, I then created a second page, test2.html. So my exact match pattern is: "http://www.mydomain.com/test.html" And the rule is supposed to do a 301 redirect to "http://www.mydomain.com/test2.html " The redirect never happens. I created the steps for the rule based on the instructions in this page: http://learn.iis.net/page.aspx/461/creating-rewrite-rules-for-the-url-rewrite-module/ I don't see that I left out a step. After I apply the rule I've even gone as far as doing an IISReset to make sure it would be in effect but still no luck. Any thoughts on what I might have left out? (Note: my rewrite rules dont include the " " around them but I had to add since serverfault thinks I am trying to spam the system with multiple urls.)

  Read the article

• Outlook 2007 will not send/receive using RPC over HTTP to an exchange server.. works for other users

  - by bob franklin smith harriet

  I have an incredibly frustrating user issue that I have been unable to resolve for over a week, any ideas for this would be greatly appreciated. The user is having troubles using Outlook 2007 to send or receive emails over using RPC over HTTP (Outlook Anywhere) to an exchange server. Basically what happens, the connection will be establised and the user will be prompted for the username and password, those are submitted and then outlook tries to download emails which fails and the connection to the exchange server will remain unavailable. The machine can ping and everything to the exchange server there is no connection issue there. The setup worked fine for him up untill now and also works for possibly hundreds of other users using the exact same settings, also the same settings will work from the users iphone on the same internet connection, and from my own system using outlook. The exchange server has the webmail https feature and that can be logged into and send and receive emails fine. Steps taken so far: removing the .ost file for the account and allowing office to rebuild it (fixes the issue for a short period of time, then the same symptons occur) deleted exchange profile and recreated (no change in issue) uninstalled all antivirus and firewalls (no change in issue) removed all cached passwords (keymgr.dll) (no change in issue) removed all entries from the hosts file (no change in issue) uninstalled and reinstalled office 2007 (Temporary fix of issue) Installing Symantec Endpoint Client caused a lot of email scan popups to be displayed, after a reboot this stopped and a scan it picked a few trojans that it removed. This fixed the issue temporarily as well, the issue is back again now. I am completely out of ideas now, there seems to be nothing that can be done to fix this issue outside of rebuilding the PC which is a massive pandoras box I don't want to enter with this user. --- Update ---- Malware scans from multiple products have been run on the machine and all updates were installed. The real problem with this user is his distance from us, there is no way to supply a spare laptop or rebuild the machine currently.

  Read the article

• Application to automate Windows software installation in a test lab

  - by Marc

  I have several test environments (hyper-V) which contain a variety of windows servers. Each machine needs periodically rolling back to a given snapshot and then re-installing with the latest version of our software to test. The software installs are quite complex MSI's with a fair few option screens. I know that the installs can be driven from the command line, passing in parameters to override the wizard options. At the simplest level I suppose I could just write a batch file to kick off each install with the required parameters, however the values that are passed in do need to change from time to time (and environment to environment) so a tool with a config file and simple GUI seems like a better idea. I think what makes it slightly more painful is the multiple environments. For example one environment might contain 4 servers and need a config file with all the server names, service endpoints etc. Another environment might be a 1-box install with all names and endpoints set to localhost. So, ideally I want to be able to store different setup configurations and use them to run all the required installers with the relevant settings against the relevant machines. Before I go off to write the thing, does anyone know of an existing, simple, free tool that will let me achieve this?

  Read the article

• DMG image containing Mac OS X 10.6.5 update not recognized

  - by Lawliet

  Hello, I want to update my Mac OS X 10.6.3 and want to use the manual package update (not Software Update) and I am having this problem for two days now. First I downloaded Mac OS X 10.6.5 Combo update and on the first opening it popped up a message saying "Unable to mount: disk image not recognized". I thought that somehow the image became corrupt during the download, so I downloaded it again. Same result. And I downloaded again. And again... No use, it still states that the .dmg is not recognized. Then I tried to update my system from 10.6.3 to 10.6.4 using the same method (package installer). It worked. And of course I downloaded the 10.6.5 update (not the combo package, but the 10.6.4 10.6.5 update package)... guess what. Not recognized. I don't understand how is this possible. Did anyone has the same problem? Please don't advice me to use software update, as I need to do that on multiple Macs Thanks in advance.

  Read the article

• Trouble installing SSL Certificate on Apache

  - by jahufar

  We have a dedicated server with GoDaddy running Plesk that requires SSL. I've generated the certificate files and I created a vhost_ssl.conf (since I can't edit the default plesk apache configuration http.include, vhost_ssl.conf gets Included to httpd.include) that tells apache where to find the certificate files: SSLCertificateFile /usr/local/psa/var/certificates/domain.com.crt SSLCertificateKeyFile /usr/local/psa/var/certificates/domain.com.key SSLCertificateChainFile /usr/local/psa/var/certificates/sub.class1.server.ca.pem When I stop/start apache, it refuses to start up. The error_log does not have anything on it either (which is strange). Then I opened up httpd.include and found this bit: <VirtualHost 208.xxx.xxx.xxx:443> ServerName domain.com:443 ServerAlias www.domain.com UseCanonicalName Off SSLEngine on SSLVerifyClient none SSLCertificateFile /usr/local/psa/var/certificates/certagC9054 Include /var/www/vhosts/domain.com/conf/vhost_ssl.conf Then I commented out SSLCertificateFile /usr/local/psa/var/certificates/certagC9054 (which is plesk's SSL certificate) and restarted apache and it worked perfectly fine. It seems that Apache does not like multiple SSLCertificateFile within the same VirtualHost directive? As anyone who worked with plesk knows, I can't just remove SSLCertificateFile directive in httpd.include as plesk will overwrite my changes when someone uses it - which is why it's in vhost_ssl.conf. So I'm stuck and this is beyond my meager admin skills. Would appreciate someone who knows what (s)he's doing to tell me whats going on. Thanks in advance.

  Read the article

• Microsoft Windows DHCP: Steering IPv4 clients into specific scopes based on MAC

  - by Easter Sunshine

  We have visitors on our campus who bring their own laptops and devices and use our wireless and wired networks. When we receive a copyright infringement notice (typically BitTorrenting), we are required to quarantine that MAC address so that it no longer has Internet access. No matter what website it tries to visit, it is sent to a web page explaining to the user that the device has been quarantined. We have thus far implemented this in ISC DHCP on Linux. We have multiple VLANs with one or more public-IP subnets and one RFC1918 quarantine subnet each. All clients are leased IPs in the public-IP subnet(s) unless you're in a list of known bad MACs. Then, you are sent to the quarantine subnet so that your traffic is unroutable on the Internet (you are isolated by subnet only, not by VLAN). We would like to move to Windows DHCP in light of the IPAM role but I cannot figure out how to replicate this in Windows DHCP 2012 (Assign DHCP IPs for specific MAC prefixes on Windows Server 2008 R2 suggests it was not possible in 2008 R2), even while using policies. So here's what I'd like: The administrator/help desk provides and maintains a list of MAC addresses that are to be quarantined. The DHCP server places those MACs into the quarantine subnet on the respective VLAN, no matter which VLAN the client is in. I don't think reservations would work: We currently have about 300 registered bad MACs and about 12 VLANs. I don't want to make 300 x 12 reservations nor have to add 12 reservations per new MAC address. Not to mention all of the quarantine subnets are /24s. We do not have NPS/NAC. You do not have to register your MAC address get network access. We use Cisco routers/switches. Thanks.

  Read the article

• How to configure mod_proxy_balancer to gracefully fail under high load

  - by bramp

  We have a system which has one Apache instance in front of multiple tomcats. These tomcats then connect to various databases. We balance the load to the tomcat with mod_proxy_balancer. Currently we are receiving 100 requests a second, the load on the Apache server is quite low, but due to database heavy operations on the tomcats, the load there is roughly 25% (of what I estimate they can handle). In a few weeks there is an event happening and we estimate that our requests will jump significant, maybe by a factor of 10. I'm doing everything I can do reduce the load on our tomcats, but I know we are going to run out of capacity, so I would like to fail gracefully. By this I mean, instead of trying to deal with too many connections which all timeout, I would like Apache to somehow monitor average response time, and as soon as the response time to Tomcat is getting above some threshold, I would like a error page displayed. This means that users who are lucky still get a page rendered quickly, and those who are unlucky get a error page quickly. Instead of everyone waiting far too long for their page, and eventually everyone timing out, and the database being swamped with queries which are never used. Hopefully this makes sense, so I was looking for suggestions on how I could achieve this. thanks

  Read the article

• SSH as root using public key still prompts for password on RHEL 6.1

  - by Dean Schulze

  I've generated rsa keys with cygwin ssh-keygen and copied them to the server with ssh-copy-id -i id_rsa.pub [email protected] I've got the following settings in my /etc/ssh/sshd_config file RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys PermitRootLogin yes When I ssh [email protected] it still prompts for a password. The output below from /usr/sbin/sshd -d says that a matching keys was found in the .ssh/authorized_keys file, but it still requires a password from the client. I've read a bunch of web postings about permissions on files and directories, but nothing works. Is it possible to ssh with keys in RHEL 6.1 or is this forbidden? The debug output from ssh and sshd is below. $ ssh -v [email protected] OpenSSH_6.1p1, OpenSSL 1.0.1c 10 May 2012 debug1: Connecting to my.ip.address [my.ip.address] port 22. debug1: Connection established. debug1: identity file /home/dschulze/.ssh/id_rsa type 1 debug1: identity file /home/dschulze/.ssh/id_rsa-cert type -1 debug1: identity file /home/dschulze/.ssh/id_dsa type 2 debug1: identity file /home/dschulze/.ssh/id_dsa-cert type -1 debug1: identity file /home/dschulze/.ssh/id_ecdsa type -1 debug1: identity file /home/dschulze/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH_5* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 9f:00:e0:1e:a2:cd:05:53:c8:21:d5:69:25:80:39:92 debug1: Host 'my.ip.address' is known and matches the RSA host key. debug1: Found key in /home/dschulze/.ssh/known_hosts:3 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/dschulze/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Offering DSA public key: /home/dschulze/.ssh/id_dsa debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Trying private key: /home/dschulze/.ssh/id_ecdsa debug1: Next authentication method: password Here is the server output from /usr/sbin/sshd -d [root@ga2-lab .ssh]# /usr/sbin/sshd -d debug1: sshd version OpenSSH_5.3p1 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: rexec_argv[0]='/usr/sbin/sshd' debug1: rexec_argv[1]='-d' debug1: Bind to port 22 on 0.0.0.0. Server listening on 0.0.0.0 port 22. debug1: Bind to port 22 on ::. Server listening on :: port 22. debug1: Server will not fork when running in debugging mode. debug1: rexec start in 5 out 5 newsock 5 pipe -1 sock 8 debug1: inetd sockets after dupping: 3, 3 Connection from 172.60.254.24 port 53401 debug1: Client protocol version 2.0; client software version OpenSSH_6.1 debug1: match: OpenSSH_6.1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: permanently_set_uid: 74/74 debug1: list_hostkey_types: ssh-rsa,ssh-dss debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: client->server aes128-ctr hmac-md5 none debug1: kex: server->client aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST received debug1: SSH2_MSG_KEX_DH_GEX_GROUP sent debug1: expecting SSH2_MSG_KEX_DH_GEX_INIT debug1: SSH2_MSG_KEX_DH_GEX_REPLY sent debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: KEX done debug1: userauth-request for user root service ssh-connection method none debug1: attempt 0 failures 0 debug1: PAM: initializing for "root" debug1: userauth-request for user root service ssh-connection method publickey debug1: attempt 1 failures 0 debug1: test whether pkalg/pkblob are acceptable debug1: PAM: setting PAM_RHOST to "172.60.254.24" debug1: PAM: setting PAM_TTY to "ssh" debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: trying public key file /root/.ssh/authorized_keys debug1: fd 4 clearing O_NONBLOCK debug1: matching key found: file /root/.ssh/authorized_keys, line 1 Found matching RSA key: db:b3:b9:b1:c9:df:6d:e1:03:5b:57:d3:d9:c4:4e:5c debug1: restore_uid: 0/0 Postponed publickey for root from 172.60.254.24 port 53401 ssh2 debug1: userauth-request for user root service ssh-connection method publickey debug1: attempt 2 failures 0 debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: trying public key file /root/.ssh/authorized_keys debug1: fd 4 clearing O_NONBLOCK debug1: matching key found: file /root/.ssh/authorized_keys, line 1 Found matching RSA key: db:b3:b9:b1:c9:df:6d:e1:03:5b:57:d3:d9:c4:4e:5c debug1: restore_uid: 0/0 debug1: ssh_rsa_verify: signature correct debug1: do_pam_account: called Accepted publickey for root from 172.60.254.24 port 53401 ssh2 debug1: monitor_child_preauth: root has been authenticated by privileged process debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: ssh_gssapi_storecreds: Not a GSSAPI mechanism debug1: restore_uid: 0/0 debug1: SELinux support enabled debug1: PAM: establishing credentials PAM: pam_open_session(): Authentication failure debug1: Entering interactive session for SSH2. debug1: server_init_dispatch_20 debug1: server_input_channel_open: ctype session rchan 0 win 1048576 max 16384 debug1: input_session_request debug1: channel 0: new [server-session] debug1: session_new: session 0 debug1: session_open: channel 0 debug1: session_open: session 0: link with channel 0 debug1: server_input_channel_open: confirm session debug1: server_input_global_request: rtype [email protected] want_reply 0 debug1: server_input_channel_req: channel 0 request pty-req reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req pty-req debug1: Allocating pty. debug1: session_pty_req: session 0 alloc /dev/pts/1 ssh_selinux_setup_pty: security_compute_relabel: Invalid argument debug1: server_input_channel_req: channel 0 request shell reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req shell debug1: Setting controlling tty using TIOCSCTTY. debug1: Received SIGCHLD. debug1: session_by_pid: pid 17323 debug1: session_exit_message: session 0 channel 0 pid 17323 debug1: session_exit_message: release channel 0 debug1: session_pty_cleanup: session 0 release /dev/pts/1 debug1: session_by_channel: session 0 channel 0 debug1: session_close_by_channel: channel 0 child 0 debug1: session_close: session 0 pid 0 debug1: channel 0: free: server-session, nchannels 1 Received disconnect from 172.60.254.24: 11: disconnected by user debug1: do_cleanup debug1: PAM: cleanup debug1: PAM: deleting credentials

  Read the article

• How can I make Cygwin open a new window each time I use a Window 7 keyboard shortcut?

  - by Michael Gundlach

  [Update: The short answer is, if an application in the 3rd thing on your taskbar, press WindowsKey+Shift+3 to open a new instance. Hooray!] I have Chrome and Cygwin on my taskbar. Chrome's shortcut is Ctrl-Alt-C (as set through right clicking the icon and putting Ctrl-Alt-C into Chrome - Properties - Shortcut Key). Cygwin's shortcut is Ctrl-Alt-T. When I press Ctrl-Alt-C, I get a new Chrome window. Great! It's as if I had shift-clicked on the Chrome icon. When I press Ctrl-Alt-T, I get a Cygwin window the first time, but after that I just get focused on the Cygwin window. As if I had simply clicked on the Cygwin icon and not shift-clicked. As if Cygwin wasn't able to have more than one instance open. I can still shift-click the icon to get more instances. I've tried with different keys than Ctrl-Alt-T and got the same behavior. Strangely, I've twice managed to get it into a state (via just clearing and setting the shortcut key over and over) where a shortcut WOULD open multiple instances -- but it was Ctrl-Alt-G both times, which doesn't make sense to my brain which has been trained to use Ctrl-Alt-T for years. Ctrl-Alt-G usually behaves just as poorly as Ctrl-Alt-T, except for the two times when magically it started behaving properly. So I'm thinking this is a Windows 7 bug (which has existed since Windows XP at least), but I'm hoping someone knows something I don't :)

  Read the article

• Issue with SSL using HAProxy and Nginx

  - by Ben Chiappetta

  I'm building a highly available site using a multiple HAProxy load balancers, Nginx web serves, and MySQL servers. The site needs to be able to survive load balancer or web servers nodes going offline without any interruption of service to visitors. Currently, I have two boxes running HAProxy sharing a virtual IP using keepalived, which forward to two web servers running Nginx, which then tie into two MySQL boxes using MySQL replication and sharing a virtual IP using heartbeat. Everything is working correctly except for SSL traffic over HAProxy. I'm running version 1.5 dev12 with openssl support compiled in. When I try to navigate to the virtual IP for haproxy over https, I get the message: The plain HTTP request was sent to HTTPS port. Here's my haproxy.cfg so far, which was mainly assembled from other posts: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice # log 127.0.0.1 local0 user haproxy group haproxy daemon maxconn 20000 defaults log global option dontlognull balance leastconn clitimeout 60000 srvtimeout 60000 contimeout 5000 retries 3 option redispatch listen front bind :80 bind :443 ssl crt /etc/pki/tls/certs/cert.pem mode http option http-server-close option forwardfor reqadd X-Forwarded-Proto:\ https if { is_ssl } reqadd X-Proto:\ SSL if { is_ssl } server web01 192.168.25.34 check inter 1s server web02 192.168.25.32 check inter 1s stats enable stats uri /stats stats realm HAProxy\ Statistics stats auth admin:********* Any idea why SSL traffic isn't being passed correctly? Also, any other changes you would recommend? I still need to configure logging, so don't worry about that section. Thanks in advance your help.

  Read the article

• Misconfigured external monitor on Mac OS X Snow Leopard 10.6.3

  - by Mike

  I have an external monitor (specifically, an HDTV) hooked up to my 2.53GHz 13" macbook pro. This display works fine and I use it with my mac in clamshell mode (eg. with an external keyboard/mouse and the laptop closed and the built-in mac screen turned off) My Mac has multiple users on it. For User A I can use the mac with the external monitor in both clamshell and dual-monitor setups. For User B, I can use the monitor in a dual-monitor setup, but whenever I switch to clamshell mode the Mac switches to an incorrect output resolution or frequency setting that my HDTV doesn't recognize, resulting in a blank screen and a message about Unsupported Resolution. Chances are I did this to myself by misconfiguring my display settings at some point in the past, but I have no idea how to undo it. I (obviously) can't seen the display to change the settings when it's borked. I can see the display settings if I switch to Dual-monitor mode, but those settings only affect the dual monitor setup; no matter how I change the settings in dual-monitor mode, the clamshell mode setup remains borked. How can I dig myself out of this hole?

  Read the article

• ASP.NET sending email through exchange problem

  - by Solmead

  I have an exchange 2010 server running on Windows 2008 R2, I also have a remote webserver running Windows 2003 with multiple sites on it (all asp.net mvc 2 sites). I setup a Transport in exchange and all the websites on my remote web server can send email no problem to anyone in the exchange server and to any external domain. Now for my problem. I am having issues with that webserver, so I moved one of the websites to run on my exchange server, it runs well (low hit website) except that email doesn't work from that site. I tried changing the Transport in exchange to add the IP address of the local machine and the 127.0.0.1 addresses and it still isn't sending any email. Any ideas on how to get this working? The remote websites can still send email no problem, the version of the site that I had to move on the remote server can still email, but on the exchange server for that website email does not send. I would guess it is a Transport issue, since it is running on the same server a firewall shouldn't be the issue. I changed the smtp setting in web.config to localhost, and now I do receive email to my account on the exchange server, but I do not receive any emails on outside addresses. To add more description, this is a custom developed asp.net mvc 2 website. And no errors were being generated in the code when sending the email in either case.

  Read the article

• How do I configure custom URL handlers on OS X?

  - by cwd

  I've been reading a lot online about custom URL handlers / custom protocol handlers such as: Launching External Applications using Custom Protocols under OSX OS X URL handler to open links to local files I get that you can tell the system that a particular program is able to handle a certain scheme / protocol with the Info.plist file: <key>CFBundleURLTypes</key> <array> <dict> <key>CFBundleURLName</key> <string>Local File</string> <key>CFBundleURLSchemes</key> <array> <string>local</string> </array> </dict> </array> <key>NSUIElement</key> <true/> But if there are multiple applications that are capable of opening the same URL handler, such as mailto: how do you specify which one you want the system to use? There were some references to utilities like the More Internet preference pane which no longer seems to be available from the author's site. I did find it online by Googling but it seems a bit shaky - like it was written for an older OSX - perhaps Tiger. I haven't been able to find information on how to set the URL handler for protocols and custom protocols. I'm assuming there is a plist file somewhere that I can edit - or maybe there is a newer, better utility that works well with Mountain Lion?

  Read the article

• Identifying Hard Drive as performance bottleneck for desktop machines

  - by Programming Hero

  I'm working in a development team where we all use laptops so we can work in multiple locations. These laptops are proving notoriously slow for development work, but at a glance they all look to have the specification for a much faster experience: CPU - Intel Core 2 Duo T7500 Memory - 2GB of RAM We all experience the biggest delays when the hard-drives are being accessed, particularly when swap-files are being thrashed. After doing a little bit of profile, a colleague discovered that our HDDs are seeing Read/Write speeds of about 10MB/sec. This seems abnormally low and we believe it the cause of the problem. Sensibly (though somewhat annoyingly) our business wont blow money on faster drives just to see if it fixes the problem; we need to illustrate this is definitely the problem and that buying some solid-state drives will make it go away. I need some way of showing how 90% of the system resources aren't being used over the course of a day, and that whenever there is utilization, it's all in HDD reads or writes. Are there any tools I could use to provide this information? Does it seem likely the problem is going to be fixed by a faster drive? Should I be looking for alternatives?

  Read the article

• Haproxy not properly passing on X-Forwarded-For header

  - by JesseP

  I have backend web servers that receive requests by way of haproxy-nginx-fastcgi. The web app used to see multiple ip's coming through in the X-Forwarded-For header, chained together with commas (most original IP on the left). At some point in the recent past (just noticed, so not sure what caused it) something changed, and now I'm only seeing a single IP passed in the header to my web application. I've tried with haproxy 1.4.21 and 1.4.22 (recent upgrade) with the same behavior. Haproxy has the forwardfor header set: option forwardfor Nginx fastcgi_params config defines this header to be passed to the app: fastcgi_param HTTP_X_FORWARDED_FOR $http_x_forwarded_for; Anyone have any ideas on what might be going wrong here? EDIT: I just started logging the $http_x_forwarded_for variable in nginx logs, and nginx is only ever seeing a single IP, which shouldn't ever be the case, as we should always see our haproxy ip added in there, right? So, issue must either be in nginx handling of the variable coming in, or haproxy not building it properly. I'll keep digging... EDIT #2: I enabled request and response header logging in HAProxy, and it is not spitting anything out for X-Forwarded-For, which seems very odd: Oct 10 10:49:01 newark-lb1 haproxy[19989]: 66.87.95.74:47497 [10/Oct/2012:10:49:01.467] http service/newark2 0/0/0/16/40 301 574 - - ---- 4/4/3/0/0 0/0 {} {} "GET /2zi HTTP/1.1" O Here are the options i set for this in my frontend: mode http option httplog capture request header X-Forwarded-For len 25 capture response header X-Forwarded-For len 25 option httpclose option forwardfor EDIT #3: It really seems like haproxy is munging the header and just passing on a single one to the backend. This is fairly impacting to our production service, so if anyone has an ideas it would be greatly appreciated. I'm stumped... :(

  Read the article

• Losing JSESSIONID when using ProxyHTMLURLMap

  - by Matthew Schmitt

  I've setup a reverse proxy between an Apache front-end and multiple Tomcat backends. The below block of code includes the ProxyHTMLURLMap param so that the HTML can be rewritten to remove the Tomcat context path. With this setup in place, after logging into my application, an initial JSESSIONID is set properly, but when navigating to any other page, this JSESSIONID is lost and another one is set by the application. I should mention that the initial login directs to a URL that includes the current context path (i.e. https://app.domain.com/context/home), but when navigating to another page, that context path is not present in the URL (i.e. https://app.domain.com/page2). <Proxy balancer://happcluster> BalancerMember ajp://happ01.h.s.com:8009 route=worker1 loadfactor=10 timeout=15 retry=5 BalancerMember ajp://happ02.h.s.com:8009 route=worker2 loadfactor=10 timeout=15 retry=5 BalancerMember ajp://happ03.h.s.com:8009 route=worker3 loadfactor=5 timeout=15 retry=5 BalancerMember ajp://happ04.h.s.com:8009 route=worker4 loadfactor=5 timeout=15 retry=5 BalancerMember ajp://happ05.h.s.com:8009 route=worker5 loadfactor=5 timeout=15 retry=5 ProxySet lbmethod=bytraffic ProxySet stickysession=JSESSIONID </Proxy> ProxyPass /context balancer://happcluster/context ProxyPass / balancer://happcluster/context/ <Location /context/> # Rewrite HTTP headers and HTML/CSS links for everything else ProxyPassReverse / ProxyPassReverseCookieDomain / app.domain.com ProxyPassReverseCookiePath / /context ProxyHTMLURLMap /context/ / # Be prepared to rewrite the HTML/CSS files as they come back # from Tomcat SetOutputFilter INFLATE;proxy-html;DEFLATE </Location> Has anyone ever run into a similar situation?

  Read the article

• SQL Server 2005 standard filegroups / files for performance on SAN

  - by Blootac

  Ok so I've just been on a SQL Server course and we discussed the usage scenarios of multiple filegroups and files when in use over local RAID and local disks but we didn't touch SAN scenarios so my question is as follows; I currently have a 250 gig database running on SQL Server 2005 where some tables have a huge number of writes and others are fairly static. The database and all objects reside in a single file group with a single data file. The log file is also on the same volume. My interpretation is that separate data files should be used across different disks to lessen disk contention and that file groups should be used for partitioning of data. However, with a SAN you obviously don't really have the same issue of disk contention that you do with a small RAID setup (or at least we don't at the moment), and standard edition doesn't support partitioning. So in order to improve parallelism what should I do? My understanding of various Microsoft publications is that if I increase the number of data files, separate threads can act across each file separately. Which leads me to the question how many files should I have. One per core? Should I be putting tables and indexes with high levels of activity in separate file groups, each with the same number of data files as we have cores? Thank you

  Read the article

• Improving browser performance while using lots of tabs?

  - by Andrew

  My browsing habits cause me to open lots of windows and tabs, either related to different projects I'm working on or things I may want to read later. I use OSX and use about 5 spaces with multiple windows in each space. The problem is eventually I'll have around 200 or more tabs open (spread over 15-20 windows) that I don't want to close. Needless to say, my computer's performance starts to degrade. As I write this on my mobile, Safari on my laptop is locking up the computer. I used to use Chrome but found better performance with Safari. What I'd like to know, is there a graph of browser performance based on tab usage? I don't need a browser that keeps all tabs active. It would be great if the browser could increase performance by "putting tabs to sleep". Or if there was some sort of tool for saving a "workspace" of tabs that you could reactivate the next time you are working on that project. What sort of solution can you recommend to solve this problem?

  Read the article

< Previous Page | 697 698 699 700 701 702 703 704 705 706 707 708  | Next Page >