Search Results

Search found 20625 results on 825 pages for 'client'.

Page 702/825 | < Previous Page | 698 699 700 701 702 703 704 705 706 707 708 709  | Next Page >

• Very Slow DSL (ethernet) speed [New Interesting Update]

  - by Abhijit

  Very IMPORTANT and INTERESTING UPDATE: Due to some reason I just thought to do a complete new setup and this time I decided to again have openSUSE plus ubuntu. So I first reinstall lubuntu and then I installed OpenSUSE 12.2 (64 bit). Now, my DSL speed is working very normal and fine on opensuse. So this is very scary. Is it possible for any operating system to manipulate my NIC so that it will work fine only on that operating system and not on another os? Regarding positive thinking and not being paranoid, what is it that makes ONLY suse to get my NIC to work at normal speed but ubuntu can not do it? Not even fedora? Not even linux mint? What all these OS are lacking that enables suse to work great? == ORIGINAL QUESTION == I 'was' on opensuse 12.2 when my dsl speed was normal. Yesterday I switched from opensuse to ubuntu 12.04 and speed decreased. It came to range of 7-10-13-20-25-kbps. Then I switch to linux mint, and then to fedora. Still slow speed. When I was in ubuntu I disabled ipv6 but still no luck. Now I am in fedora but this time with DIFFERENT ISP. And still I am getting very slow sped. So my guess is this is nothing to do with os. What can be wrong? Is this problem of NIC? Does NIC speed decreases over time? Does NIC life ends over time as with keyboard or mouse? Help please All the os I used are 64 bit and my laptop is Compaq Presario A965Tu Intel Centrino DUal Core. Interesting thing to notice is I get normal speed while downloading torrent inside torrent client softwares. This slow speed issue applied to download from any web browser or installing software using terminal.

  Read the article

• Shoretel Upgrade Path

  - by Brian

  I currently have a Shoretel Server running Server 2003 x32 as a virtual machine paired with a ShoreGear 90 switch and another unused switch of the same model being reserved for manual failover. I am getting the software mailed to me from my partner, but with limited support since the server is in a relatively remote area. I am tempted to upgrade the OS at the same time as performing the upgrade, but want to know if there are any horror stories or advice I should know about before diving in. I'm upgrading from Shoretel 9.2 Build. I will be upgrading first to version 10.1 then finally to 11.1. The system has been bullet proof since it was installed and we are upgrading mainly to get a client that is a little more modern. My question boils down to: Should I even bother with an OS upgrade or even possibly a fresh install of Windows with an install of Shoretel 11.1 and just transfer the configuration? Should I just stay with Server 2003 since it is supported in my target version of Shoretel and the upgrade will be more than enough to keep me busy as a novice?

  Read the article

• scponly worked but didn't chroot the home folder, the user can still browse the entire server.

  - by Mint

  So I followed the "Chroot and Debian" tutorial in http://sublimation.org/scponly/wiki/index.php/FAQ Then when I log into user "upload" via ssh I have no access to the command line (this is what I wanted). But then when I SFTP into the upload user I can still see all the root files (/), it didn't chroot me to just /home/upload whats going on? …. I added this to the end of my /etc/ssh/sshd_config file, then done a restart Subsystem sftp internal-sftp UsePAM yes Match User upload ChrootDirectory /home/upload AllowTCPForwarding no X11Forwarding no ForceCommand internal-sftp Then when I log into sftp I can only see my upload folder (this is what I want), but now scp doesn't work :P SCP will accept my password then: debug1: Next authentication method: password [email protected]'s password: debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = en_NZ.UTF-8 debug1: Sending command: scp -v -t /test It will hang on that last debug message. Any help would be greatly appreciated. Note, running Debian Lenny

  Read the article

• "Dictionary problem." Error with VMPlayer

  - by George Mauer

  I'm pretty new to using vmware virtualization (been a virtualbox user) so I'm hoping you guys can help me out. I recently got an external usb disk containing a vm for a client, downloaded vmplayer, set it up with "Open a Virtual Machine", ran it, easy as pie. After working with it a bit this morning, I shut the VM down and now trying to start it back up again I get this: I tried removing the vm from my library, now it happens whenever I try to add it back in. In the meantime, I can still access other virtual machines so it seems like the problem might be with the virtual disk. So two questions: This is obviously not a very helpful error message. Where can I go to get more information? My Application EventLog doesn't contain anything from VMWare. What steps can I take to fix the problem? Edit: A couple more pieces of information. I did not take any snapshots. I don't think VM Player even has that ability. I have a zip file of (what I assume) is the state of the VM when it was sent to me. I cannot unzip it as it is huge and simply requires more HD space than I have available but I did extract the vmx file and examine it. Other than the UUIDs and the fact that mine reads cleanShutdown = "FALSE" they are identical. The log contains the following lines Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead: Unable to load dict from 'E:....\MachineName.vmsd'. Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead failed for file 'E:....\MachineName.vmx': Dictionary problem (6) Jun 23 10:11:18.082: vmx| SNAPSHOT: Snapshot_TimeStampTiers failed: Dictionary problem (6)

  Read the article

• Correct use of SMTP "Sender" header?

  - by Eric Rath

  Our web application sends email messages to people when someone posts new content. Both sender and recipient have opted into receiving email messages from our application. When preparing such a message, we set the following SMTP headers: FROM: [email protected] TO: [email protected] SENDER: [email protected] We chose to use the author's email address in the FROM header in an attempt to provide the best experience for the recipient; when they see the message in their mail client, the author is clear. To avoid the appearance of spoofing, we added the SENDER header (with our own company email address) to make it clear that we sent the message on the author's behalf. After reading RFCs 822 and 2822, this seems to be an intended use of the sender header. Most receiving mail servers seem to handle this well; the email message is delivered normally (assuming the recipient mailbox exists, is not over quota, etc). However, when sending a message FROM an address in a domain TO an address in the same domain, some receiving domains reject the messages with a response like: 571 incorrect IP - psmtp (in reply to RCPT TO command) I think this means the receiving server only saw that the FROM header address was in its own domain, and that the message originated from a server it didn't consider authorized to send messages for that domain. In other words, the receiving server ignored the SENDER header. We have a workaround in place: the webapp keeps a list of such domains that seem to ignore the SENDER header, and when the FROM and TO headers are both in such a domain, it sets the FROM header to our own email address instead. But this list requires maintenance. Is there a better way to achieve the desired experience? We'd like to be a "good citizen" of the net, and all parties involved -- senders and recipients -- want to participate and receive these messages. One alternative is to always use our company email address in the FROM header, and prepend the author's name/address to the subject, but this seems a little clumsy.

  Read the article

• Unable to ssh in Beagle Bone Black

  - by SamuraiT

  I wanted to install pip onto beagle bone black,and I tried this: /usr/bin/ntpdate -b -s -u pool.ntp.org opkg update && opkg install python-pip python-setuptools then, it threw errors,but Unfortunately, I didn't log that errors. it was occurred a week ago and was't solved yet. I wanted to solve it now and I tried connect by ssh,but I failed. When I ping to beagle bone, it responds, and Cloud9 IDE is working too but not ssh. I don't think this is serious problem since I can connect to beagle bone by other methods: Cloud9 or so. However, to use python on beagle bone, I need to connect by ssh. Before trying to update and install python-pip, I could connect by ssh. Do you have any ideas to solve this connection problem? note I use default OS: Angstrom I don't use SD card. HOST PC is mac, OS.X 10.9 connect by USB serial I checked this but this wasn't helpful http://stackoverflow.com/questions/19233516/cannot-connect-to-beagle-bone-black I could connect by GateOne SSH client, but still unable to connect from terminal.

  Read the article

• Win 8.1 Hyper-v Full Screen and VPN problems

  - by tr0users

  I need to connect to my office using Cisco VPN software (RSA). Once connected all my internet traffic goes through the employer's VPN and this prevents me from listening to spotify. As a way around this I created a Win 2012 VM that I run in hyper-v from my Windows 8.1 Client. First I RDP to the VM, then I connect to the VPN. This forces the RDP session between my host laptop and the VM to close. I then open the hyper-v manager and double-click my VM to get a connection back (not great because I don't get the use of copy & paste this way). Previously when I opened my VM this way I would have full screen. I'm using a 1920x1080 monitor. Today when I re-open my connection to the VM it is displayed in a window that uses maybe 75% of the full screen. I have tried the menu option View\Full Screen Mode only centres the screen and apply black borders around the outside. Could anyone please suggest how I may solve the VPN or Full Screen problems? Thanks Rob.

  Read the article

• saving and searching encrypted mail

  - by user53616

  I often send and receive gpg-encrypted mail. At the moment I use thunderbird + enigmail (in linux) to do that. As far as I know there is no way in thunderbird to find all encrypted messages which bodies contain particular keywords. There also seems to be no option to save encrypted mails decrypted (so they would be searchable). However for me it is important to be able to search old encrypted mails. So my question is: Is there a way in linux to save incoming mails automatically decrypted in my inbox and save outgoing encrypted mail decrypted in the send folder? Both times adding a line to the body which remarks that the mail was encrypted. It could be another email client for linux that could to that or perhaps a solution using procmail or maildrop. For a procmail solution I guess there could be some problems with encoding (perhaps one have to use emil?). Note that the solution should work for multipart encrypted messages (including encrypted attachments) too. Further note that I don't want a discussion about security holes. For me it's ok if messages are stored decrypted on my harddrive (which is encrypted as a whole anyway). In doubt for a first solution it would be ok to store my private key passphrase in cleartext on my harddrive, too. The point is that the mails are encrypted on the mailserver or more generally on their "way through the net".

  Read the article

• DNS resolve .com domain on local domain

  - by Joost Verdaasdonk

  I'm building a local 2008 R2 domain as a test case to be able to write a roadmap for the real new domain that needs to be created soon. What I would like to know if I'm able to make a record in DNS that will point the domain name: www.example.com and example.com to one of the servers in my network. I tried creating an a-record for it but that doesn't work. To be honest I'm not even sure if this is possible? So can I do this? That way I would be able to fully test all our services (and webb app) offline before I build the real domain and switch the DNS records at the provider. Some advice if possible and where to start is appreciated. The solution (Thanks Brent): Create new Forward lookup zone pointing to example.com Create empty A record pointing to IP of the webserver you are targeting If www is needed create A record with Name: www and IP of your webserver sub domains repeat the process but then with names for example: sub or www.sub (and ip your webserver) Be aware of the DNS Cache while you are in this process. Things can take time or do the following: Right click the server and choose clear cache in CMD: ipconfig /flushdns (to flush the client cache)

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

• How can I stop Excel from eating my delicious CSV files and excreting useless data?

  - by atroon

  I have a database which tracks sales of widgets by serial number. Users enter purchaser data and quantity, and scan each widget into a custom client program. They then finalize the order. This all works flawlessly. Some customers want an Excel-compatible spreadsheet of the widgets they have purchased. We generate this with a PHP script which queries the database and outputs the result as a CSV with the store name and associated data. This works perfectly well too. When opened in a text editor such as Notepad or vi, the file looks like this: "Account Number","Store Name","S1","S2","S3","Widget Type","Date" "4173","SpeedyCorp","268435459705526269","","268435459705526269","848 Model Widget","2011-01-17" As you can see, the serial numbers are present (in this case twice, not all secondary serials are the same) and are long strings of numbers. When this file is opened in Excel, the result becomes: Account Number Store Name S1 S2 S3 Widget Type Date 4173 SpeedyCorp 2.68435E+17 2.68435E+17 848 Model Widget 2011-01-17 As you may have observed, the serial numbers are enclosed by double quotes. Excel does not seem to respect text qualifiers in .csv files. When importing these files into Access, we have zero difficulty. When opening them as text, no trouble at all. But Excel, without fail, converts these files into useless garbage. Trying to instruct end users in the art of opening a CSV file with a non-default application is becoming, shall we say, tiresome. Is there hope? Is there a setting I've been unable to find? This seems to be the case with Excel 2003, 2007, and 2010.

  Read the article

• 404 with serving static files in a custom nginx configuration

  - by code90

  In my nginx configuration, I have the following: location /admin/ { alias /usr/share/php/wtlib_4/apps/admin/; location ~* .*\.php$ { try_files $uri $uri/ @php_admin; } location ~* \.(js|css|png|jpg|jpeg|gif|ico|pdf|zip|rar|air)$ { expires 7d; access_log off; } } location ~ ^/admin/modules/([^/]+)(.*\.(html|js|json|css|png|jpg|jpeg|gif|ico|pdf|zip|rar|air))$ { alias /usr/share/php/wtlib_4/modules/$1/admin/$2; } location ~ ^/admin/modules/([^/]+)(.*)$ { try_files $uri @php_admin_modules; } location @php_admin { if ($fastcgi_script_name ~ /admin(/.*\.php)$) { set $valid_fastcgi_script_name $1; } fastcgi_pass $byr_pass; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/php/wtlib_4/apps/admin$valid_fastcgi_script_name; fastcgi_param REDIRECT_STATUS 200; include /etc/nginx/fastcgi_params; } location @php_admin_modules { if ($fastcgi_script_name ~ /admin/modules/([^/]+)(.*)$) { set $byr_module $1; set $byr_rest $2; } fastcgi_pass $byr_pass; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/php/wtlib_4/modules/$byr_module/admin$byr_rest; fastcgi_param REDIRECT_STATUS 200; include /etc/nginx/fastcgi_params; } Following is the requested url which ends up with "404": http://www.{domainname}.com/admin/modules/cms/styles/cms.css Following is the error log: [error] 19551#0: *28 open() "/usr/share/php/wtlib_4/apps/admin/modules/cms/styles/cms.css" failed (2: No such file or directory), client: xxx.xxx.xxx.xxx, server: {domainname}.com, request: "GET /admin/modules/cms/styles/cms.css HTTP/1.1", host: "www.{domainname}.com" Following urls works fine: http://www.{domainname}.com/admin/modules/store/?a=manage http://www.{domainname}.com/admin/modules/cms/?a=cms.load Can anyone see what the problem could be? Thanks. PS. I am trying to migrate existing sites from apache to nginx.

  Read the article

• Why is REMOTE_ADDR only sometimes available as an Apache environment variable?

  - by Xiong Chiamiov

  To avoid having to parse X-Forwarded-For in Varnish, I'm trying to just set a header on the SSL terminator (currently Apache) that stores the direct client IP in a header. On our development machine, this works: RequestHeader set X-Foo %{REMOTE_ADDR}e However, in staging it doesn't. Specifically, the header is empty, as illustrated by both varnishlog: 13 TxHeader b X-Foo: (null) (On the development machine, this shows the IP address as expected.) Similarly, logging REMOTE_ADDR shows that it only appears to be populated on the dev machine: # Config LogFormat "%{X-Forwarded-For}i %{REMOTE_ADDR}e" combined CustomLog "/var/log/httpd/access_log" combined # Log file, staging <my ip> - # Log file, development <my ip> <my ip> Since the dev machine is, well, a dev machine, it is different in a number of ways; however, I can't track down which difference is causing this. The versions of Apache are the same (2.2.22), and I don't see anything relevant in any of the standard config files or /etc/sysconfig/httpd. And the rest of the system is reasonably similar, since they're built off the same CentOS 5 base image. I can't even tell from the Apache documentation whether REMOTE_ADDR is expected to exist or not as an environment variable, but it clearly works on one machine, whether by fluke or design, and the inconsistency is driving me mad.

  Read the article

• SSH Connection Error : No route to host

  - by dewbot

  There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

  Read the article

• Setting up apache vhost for Icinga

  - by DKNUCKLES

  It's been a while since I've worked with Apache so please be kind - I'm also aware of this question but it hasn't been much help to me. I'd like to set up a simple vHost w/ Apache for my Icinga instance. Icinga is up and running and I can access it from x.x.x.x/icinga, however would like to be able to access it externally as well as internally. I have set up the /etc/hosts file and the following is my barebones vhost statement in httpd.conf <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /usr/share/icinga ServerName icinga.domain.com ErrorLog logs/icinga.com-error_log CustomLog logs/dummy-host.example.com-access_log common </VirtualHost> I also have the following in my .htaccess file <Directory> Allow From All Satisfy Any </Directory> An entry has been made for the instance in the Windows DNS server on my network, however when I try to access the site by URL I am greeted with Internal Server Error. Reviewing the /var/log/icinga.com-error_log I see the following entry. [Thu Dec 13 16:04:39 2012] [alert] [client 10.0.0.1] /usr/share/icinga/.htaccess: <Directory not allowed here Can someone help me spot the error of my ways?

  Read the article

• Changing SkyDrive default location on Windows 8.1

  - by jmblack

  Update: This issue is due to the use of any non-local location for the SkyDrive folder. I've currently worked around this by using a local folder, but this has not resolved the original problem. I am trying to change the location where SkyDrive is located in Windows 8.1. This is the newly integrated SkyDrive, and not a downloadable client. There are a couple of similar questions on this site, but they pertain to Windows 8 and 8.1 Preview: Changing the SkyDrive default path in Windows 8.1 (Windows 8.1 Preview) How do I change the SkyDrive default folder in Windows (Windows 8) The SkyDrive folder is a system folder in 8.1, and like other system folders, has a Location tab in its properties that theoretically lets you change its location. I was able to do this with other system folders such as Downloads and Pictures, but there is an error when I try to change this for SkyDrive. Edit: The location that causes this error is a mapped network drive. The error does not occur when trying to move SkyDrive to another location on the same drive. There are no permission restrictions on the mapped network drive. Edit #2: This is the method I followed that produced the error: A screenshot of the error can be found here Has anyone else encountered this or have any information on this?

  Read the article

• nginx giving of 404 when using set in an if-block

  - by ba

  I've just started using nginx and I'm now trying to make it play nice with the Wordpress plugin WP-SuperCache which adds static files of my blog posts. To serve the static file I need to make sure that some cookies aren't set, that it's not a POST-request and making sure the cached/static file exist. I found this guide and it seems like a good fit. But I've noticed that as soon as I try to set something inside an if my site starta giving 404s on an URL that isn't rewritten. The location block of the configuration: location /blog { index index.php; set $supercache_file ''; set $supercache_ok 1; if ($request_method = POST) { set $supercache_ok 0; } if ($http_cookie ~* "(comment_author_|wordpress|wp-postpass_)") { set $supercache_ok '0'; } if ($supercache_ok = '1') { set $supercache_file '$document_root/blog/wp-content/cache/supercache/$http_host/$1/index.html.gz'; } if (-f $supercache_file) { rewrite ^(.*)$ $supercache_file break; } try_files $uri $uri/ @wordpress; } The above doesn't work, and if I remove all the ifs above and add if ($http_host = 'mydomain.tld') { set $supercache_ok = 1; } and then I get the exact same message in the errors.log. Namely: 2010/05/12 19:53:39 [error] 15977#0: *84 "/home/ba/www/domain.tld/blog/2010/05/blogpost/index.php" is not found (2: No such file or directory), client: <ip>, server: domain.tld, request: "GET /blog/2010/05/blogpost/ HTTP/1.1", host: "domain.tld", referrer: "http://domain.tld/blog/" Remove the if and everything works as it should. I'm stymied, no idea at all where I should start searching. =/ ba@cell: ~> nginx -v nginx version: nginx/0.7.65

  Read the article

• How to setup ping between XP guest from Win8 Host using Hyper-V virtual swtich

  - by rism

  Hyper-V client is installed on a Win8 Pro 64 bit box and a VM running XP has been created within that with an internal virtual swtich. The VM can be booted and accessed and there is a default virtual NIC within it with dynamic IP of 169.254.x.x which i have changed to be a static IP of 192.168.0.12/255.255.255.0 confirmed via ipconfig on the XP guest. The Host has IP of 192.168.0.7/255.255.255.0. Both host and guest have their firewalls disabled for simplicity. I cant ping guest from host nor host from guest. TTL timeout. And with regard to Hyper-V and VMs I dont know what to do next. Both are in same workgroup (as per name) but since they cant ping I guess that means nothing. .... My objective is to share a folder on VM so I can install a 32bit accountancy app that wont run on Win8/7 so if there is a more simplistic way then Im all ears but typically a peer to peer is very simple.

  Read the article

• How do I send e-mails with attachments to a Microsoft WebTV user?

  - by Petr 'PePa' Pavel

  my friend uses Microsoft WebTV (e-mail address ends with @webtv.net) and I'd like to send him an e-mail with a picture attached to it. We went through a series of attempts one of which ended up a success, all others a failure. He just can't see my e-mail in his mailbox, when it contains an attachment. E-mails without attachments always go through all right. What seemed to help in the first successful case, was that he added my e-mail address to his address book and my e-mail suddenly showed up. Seemed to have been delivered before but hidden. He kept my address in his address book however, it didn't help with the following trials. He did look into his junk folder, nothing there. I made sure the file name contains no spaces. It's a regular jpeg, named something-like-this.jpg I downsized it to have only about 50k, as I've read somewhere that that's a limit. I actually doubt this piece of information, because I think the successful attempt was larger. webtv.net contains zero information. I watched their video demo for the e-mail client, so I at least know how the user interface looks like. I've never laid my hands on the real thing. I'm an advanced user myself (a programmer) but I can't wrap my mind around this. He on the other hand, is a very technically inexperienced user and because he's half way across the globe, I can't come and look over his shoulder. He doesn't have a computer, afaik there's no way I could see what he sees. Any ideas on how to debug this? Thanks for your time, guys. P.S. I can't tag this "webtv" because such tag doesn't exist yet and my reputation is too low, sorry.

  Read the article

• SBS 2008 R2: Did something change with anonymous relays?

  - by gravyface

  Have noticed that prior documentation on setting up anonymous relays in SBS 2008 no longer work without some additional configuration. Used to be able to follow this documentation, which is basically: setup a new receive connector add the IP address(es) that will be permitted to relay check off "anonymous" under Permission Group and then run the Exchange shell script to grant permissions. Now what seems to be happening is that if the permitted IP address happens to fall within the same address space as another more restrictive Receive Connector (like the "Default SBS08" one) and possibly if it's ahead of the new Receive Connector alphabetically (haven't tested that yet), the relay attempt fails with "Client Was Not Authenticated" error. To get it to work, I had to modify the scope of the "Default SBS08" Receive Connector to exclude the one LAN IP that I wanted to allow relaying for. I can't recall ever having to do this for Exchange 2007 Standard and/or any other SBS 2008 servers I've setup over the last couple of years and I don't remember doing this and the wiki entry I added at the office doesn't mention it either. So my question is, has anyone else experienced this? Has there been a new change with R2 or perhaps an Exchange Service Pack?

  Read the article

• How to Access User Directory shared by Apache on OS X Mountain Lion?

  - by schluchc

  When trying to access the local user web page on localhost/~username, I get a "403 Forbidden". The system web page in /Library/WebServer/Documents is accessible on localhost/ though, so I assume Apache is working fine. I know that this problem has been discussed several times, also on superuser. I implemented and checked all I could find, but I still couldn't solve the problem and would be glad if someone had a suggestion for this particular case: sudo apachectl -t returns Syntax OK. I have a username.conf file in /etc/apache2/users/: <Directory "/Users/username/Sites/"> Options Indexes MultiViews FollowSymLinks AllowOverride AuthConfig Limit Order allow,deny Allow from all </Directory> as proposed here [SuperUser] and in several other tutorials. The permissions of the username.conf file are -rw-r--r-- root wheel, as they should be. The httpd.conf is unchanged and therefore contains the line Include /private/etc/apache2/extra/httpd-userdir.conf. That file in turn contains UserDir Sites Include /private/etc/apache2/users/*.conf <IfModule bonjour_module> RegisterUserSite customized-users </IfModule> So the httpd*.conf files should be ok. The permissions of /Users/username/Sites is drwxr-xr-x 10 username staff and -rw-r--r--@ 1 username staff for the index.html. In the error log I simply get a [Sun Nov 25 22:14:32 2012] [error] [client 127.0.0.1] (13)Permission denied: access to /~username/ denied. And yes, after each change I did the sudo apachectl restart. Any help no how to solve the problem or how to further analyze it would be highly appreciated!

  Read the article

• One Windows Domain workstation can ping gateway but gets no internet access

  - by dindeman

  One of the (Windows XP SP3) workstations of our Windows Domain could not access internet anymore, this problem suddenly happened overnight. The domain controllers (there are three of them) are all running Windows Server 2008. First I compared the output of ipconfig /all on the faulty workstation with the output of a working workstation and it was just fine as it had always been. In particular the default gateway was correct and always remained pingable from the faulty workstation. I guessed that something was wrong with the DHCP service and I restarted the DHCP server service on all of our three DCs as well as the DHCP client service on the faulty workstation. This didn't solve the issue. I then thought of renewing the DHCP lease with ipconfig /release and ipconfig /renew and here is my first question: why did this never work? The same IP address (192.168.0.45) kept being assigned despite all my attempts to renew it (note that all our workstation are getting their TCP/IP automatically.) Even by leaving the domain and changing the computer name the same address was yet again obtained... Anyway I then proceeded to switch the TCP/IP configuration for that machine manually to another free valid IP address (192.168.0.41)... and then the internet access came back! I then cleared any traces of the previous IP in the DHCP leases list and in the DNS tables of our DCs and, after setting back the TCP/IP configuration to 'automatic', finally, the new lease would be granted (192.168.0.41) alongside with the internet access. My second question: what went suddenly wrong with the original IP address?

  Read the article

• IPv6 works only after ping to routing box

  - by Ficik

  Situation: There is ipv4 only router in network and every computer is connected to it (wifi or cable). Server with ipv4 and ipv6 is connected to this router as well. Server has configured tunnelbrokers 6to4 tunnel and radvd. Clients in network has right prefix and can ping each other. But they can't ping to internet until they ping Server (the one with tunnel). I found somewhere that it's icmp problem, but I couldn't find solution. Is it problem that there is ipv4 only router? server and client runs linux router runs dd-wrt without ipv6 support :( Ping try: standa@standa-laptop:~$ ping6 ipv6.google.com PING ipv6.google.com(2a00:1450:8007::69) 56 data bytes ^C --- ipv6.google.com ping statistics --- 29 packets transmitted, 0 received, 100% packet loss, time 28223ms standa@standa-laptop:~$ ping6 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478 PING 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478(2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478) 56 data bytes 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=1 ttl=64 time=3.55 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=2 ttl=64 time=0.311 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=3 ttl=64 time=0.269 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=4 ttl=64 time=0.292 ms ^C --- 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3000ms rtt min/avg/max/mdev = 0.269/1.107/3.559/1.415 ms standa@standa-laptop:~$ ping6 ipv6.google.com PING ipv6.google.com(2a00:1450:8007::69) 56 data bytes 64 bytes from 2a00:1450:8007::69: icmp_seq=1 ttl=57 time=20.7 ms 64 bytes from 2a00:1450:8007::69: icmp_seq=2 ttl=57 time=20.2 ms 64 bytes from 2a00:1450:8007::69: icmp_seq=3 ttl=57 time=23.4 ms ^C --- ipv6.google.com ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2001ms rtt min/avg/max/mdev = 20.267/21.479/23.413/1.392 ms

  Read the article

• Ngins wont send POST to fastcgi backend, but GET works fine?

  - by xyld

  Not sure why, but it is happy sending a GET to the fastcgi backend (Mercurial hgwebdir in this case), but simply resorts to the filesystem if the request is a POST. Relevant parts of nginx.conf: location / { root /var/www/htdocs/; index index.html; autoindex on; } location /hg { fastcgi_pass unix:/var/run/hg-fastcgi.socket; include fastcgi_params; if ($request_uri ~ ^/hg([^?#]*)) { set $rewritten_uri $1; } limit_except GET { allow all; deny all; auth_basic "hg secured repos"; auth_basic_user_file /var/trac.htpasswd; } fastcgi_param SCRIPT_NAME "/hg"; fastcgi_param PATH_INFO $rewritten_uri; # for authentication fastcgi_param AUTH_USER $remote_user; fastcgi_param REMOTE_USER $remote_user; #fastcgi_pass_header Authorization; #fastcgi_intercept_errors on; } GET's work fine, but POST delivers this error to the error_log: 2010/05/17 14:12:27 [error] 18736#0: *1601 open() "/usr/html/hg/test" failed (2: No such file or directory), client: XX.XX.XX.XX, server: domain.com, request: "POST /hg/test HTTP/1.1", host: "domain.com" What could possibly be the issue? I'm trying to allow read-only access via GET's to the page, but require authorization when using hg push to the same url which sends a POST request.

  Read the article

• Blocking of certain file downloads

  - by Philip Fourie

  I have a problem where I cannot completely download a certain file from a server. The file is 1.9MB in size but only 68% is downloaded and then it hangs. I tried and these cases, which failed: Downloaded the file with HTTP Downloaded the file with FTP Moved the file to different FTP and web servers behind the ISA firewall Tried with IIS 6.0 & IIS 7.0 Multiple download clients. Which included FireFox, FileZilla (on Windows) and wget (on Linux) This worked: Downloading other files from the same location on the server. Both bigger and smaller and in size than the original. FTP and HTTP worked. Earlier version of this file (.DLL) works. It is as if the content of this file has an influence on this file being served. Network architecture: Client Machine - Internet (ISP) - ISA Server - IIS 7.0 The only constants are the ISP, Cisco router and the ISA server. Is it possible that something is rejecting the download because of the contents of the file? I am hoping ISA is the culprit... I am not a ISA expert is there somewhere I can look to establish if it is indeed ISA causing this? Update: Splitting the file into two parts with a hex editor results in one half of the file being served correctly and the other part not. Zipping the file results in the file being downloaded successfully. However this is not an option for this particular scenario. Renaming the file and its extension also doesn't work. Update 2009/10/22: It does NOT seems to be ISA that is causing this problem. We connected a laptop (running IIS) on an available public IP and still the file download to 68% before it hanged. The two remaining components are the ISP and the Cisco 800 series router. Anyone knows about an issue on the router perhaps?

  Read the article

< Previous Page | 698 699 700 701 702 703 704 705 706 707 708 709  | Next Page >