Search Results

Search found 55281 results on 2212 pages for 'j set'.

Page 702/2212 | < Previous Page | 698 699 700 701 702 703 704 705 706 707 708 709  | Next Page >

• Find the IP of the router between me and main router/gateway?

  - by Crash893

  I have a Netgear router that is the main router/gateway in and out of the network. Then I have a Linksys 54g router with WiFi that we use as are main WiFi access point The Cat5 runs from the router to the WiFi routers LAN port (not WAN). And then if you connect to that WAP you are basically on the network. I want to be able to find out what the IP address of that WAP is but so far I can't figure out how to: I've tried doing a tracert to the gateway IP but I get nothing. I've scanned all the IP addressed in the network. I've gone to the Netgear main router and looked under attached devices but it doesn't say anything. Any ideas on how I can figure out how to administer it? (I do have limited physical access but my attempt to plug into it came back with a faulty IP (in the 169 range where the rest of the office is 192.168...). I never set this router up to begin with so I'm reluctant to just kill it with the reset button because I can't get into see what the settings are set to.

  Read the article

• Bypassing SQUID on freebsd with PF

  - by epema

  I have PF+SQUID31 on FREEBSD-9.0, and I want to have some hosts(aka goodguys) to bypass the proxy, so that torrents are not logged. Also, I am not sure about transparent. It means that I dont have to configure proxy settings on the client side right? I have tried doing a redirect no rdr on $int_if inet proto {tcp,udp} from 192.168.1.233/32 to any However, no luck :( Here is a quick look of my conf files: SQUID /usr/local/etc/squid/squid.conf http_port 192.168.1.1:8080 transparent RC /etc/rc.conf: gateway_enable="YES" pf_enable="YES" pf_rules="/usr/local/etc/pf.conf" pflog_enable="YES" squid_enable="YES" I have squid31 installed from ports with SQUID_PF "Enable transparent proxying with PF" on PF /usr/loca/etc/pf.conf: int_if="re0" ext_if="bge0" localnet="{ 192.168.1.0/24 }" table <goodguys> const { "192.168.1.219", "192.168.1.233" } set block-policy drop set skip on lo0 scrub in all fragment reassemble scrub out all random-id max-mss 1440 block in on $ext_if pass out on $ext_if keep state block in on $int_if pass in on $int_if inet proto tcp from $int_if:network to $int_if port 8080 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 21 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 22 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 53 keep state pass in on $int_if inet proto tcp from $int_if:network to any port { smtp, pop3 } keep state pass in on $int_if inet proto icmp from $int_if:network to $int_if keep state pass out on $int_if keep state What lines should I add in conf files? I am assuming that the problem is on the firewall(pf).

  Read the article

• How can I associate html/htm files with Chrome in Windows 7 64 bit?

  - by matt

  I want Chrome to open all .html files. It is currently set as my default browser, however html files open in IE9. When I go to Control Panel\Programs\Default Programs\Set Associations I see that .html and .htm files are associated with IE. When I choose to change the default program it I'm presented with a list of programs but Chrome is not one of them. I browse to, and then select the Chrome.exe (C:\Users\Matt\AppData\Local\Google\Chrome\Application\chrome.exe) but it goes right back to IE. This is the first time I've seen anything like this. I'm running Windows 7 64 bit. I never had this problem on Windows 7 32 bit. Is this because Chrome by default installs in the User directory, not the Program Files directory? How can I fix these file associations? EDIT: It's not that things are reverting back to IE after associating them with Chrome. When I browse to Chrome in the file association window, and select it, it doesn't seem to take. It doesn't show Chrome in the list of programs despite pointing to the Chrome.exe location. I really think this has something to do with the fact that it doesn't install into the Program File Directory.

  Read the article

• Getting SMB file shares working over a PPTP VPN

  - by Ben Scott

  I'm having issues getting SMB file shares working over a PPTP VPN. The server setup consists of a security device (DrayTek V3300) which passes the PPTP authentication to a SBS2003 server running RRAS. The server is the DC and provides DNS and WINS, the single NIC's name server is set to 127.0.0.1, and DHCP on the DrayTek sets the server IP as the DNS. If I create a new VPN connection in Win7, leaving everything as default apart from the server, username, password and domain, I can: ping everything by IP address resolve IPs with nslookup using their fully-qualified name, as in nslookup fileserver.mydomain.local ping machines by fully-qualified name, as in ping fileserver.mydomain.local However if I try to access a file share: within Explorer, I get "Windows cannot access ..." with "Error code: 0x80004005 Unspecified Error", using net use z: \\fileserver.mydomain.local\share, I get "System error 53 has occurred. The network path was not found." If I add the machine name to my HOSTS file I can use the file share, which is my last-ditch workaround, but I have a number of VPN users and would rather a solution that doesn't involve me trying to hand-edit system files on computers half a country away. If I set the WINS server explicitly in the connection's IPv4 settings I don't have to use the FQN to ping the machine, but that doesn't change anything else.

  Read the article

• VirtualBox VM running web server not accessible via external IP

  - by mwigdahl

  I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

  Read the article

• Sendmail : Mail delivery of same domain to internal or external mail server.

  - by Silkograph

  Its bit difficult to explain but very simple problem. We have internal sendmail server and hosted server. Both are set to same domain name. We have mixed mail accounts. For example we have two user in one office. [email protected] is local only [email protected] is internal plus external. Internal means we create user on local linux box where sendmail is set. External means we create user on local and hosted server. [email protected] can send mails to any internal user created on Linux box where sendmail is installed. But he can not send mail to outside domain and no mail can be sent to him as there is no account created on external hosted server. [email protected] can send mails to internal as well as all other domains through sendmail's smart_host feature, which uses hosted server's smtp. [email protected] can get all external emails internally through Fetchmail on linux box. Now we have third user [email protected] who will be always outstation and can use external server only. So I can not create account on local linux box for [email protected] because his mail will get delivered locally only. I don't want to create alias and send his mails to gmail or yahoo's account. I want to send emails to his external account from any internal user. How this can be done? Thanks in advance.

  Read the article

• Port forwarding + shared connection with Ubuntu

  - by Joey Adams

  Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

  Read the article

• How can one make vim change terminal colors?

  - by amn

  I am using command line vim running from an xterm (which runs sh). I have color in vim according to a color scheme I like. The problem is, as usual with 256-color terminals and truecolor color schemes, colors are wrong. Now, I know I can do a gazillion things to fix this, including installing gvim, but I like my terminal. In fact, using xrdb [-merge] .Xresource file, I now actually have xterm override the color values, and the theme now looks perfect. Since, I may be switching to another theme, I need some workflow to have vim actually do what xrdb does - to reset terminal color pallette. Because right now I have to reset color values with xrdb ... first, then launch another xterm to actually use these values, then launch vim from that newly opened xterm to have the exact colors. The way I understood it is that vim color scheme, just as any other terminal application, uses colors by referencing their ids, and X resources set the values themselves. I think I saw somewhere on Internet, that terminal control character sequences can reset actual color values, in fact, I am sure they can - I managed to set my terminal background color at runtime. How would I make vim execute these sequences to match values for the color scheme? And is there any reference to these control sequences, as part of any standard?

  Read the article

• How to Eliminate Black Bars from Powerpoint videos ?

  - by appu

  Hi, I am running a digital signage system for my client. The basic installation is a vertically oriented 42" LCD TV with a 1920x1080 screen resolution (reverse of 1920x1080 when setup normally, i.e. landscaped). Please check out the following link for a basic screen divisions layout I want to setup. http://flickr.com/photos/55097319@N03/5410208856 In the division labeled "ppt" I plan to run a powerpoint presentation. The screen division is 360x1476 resolution. As there isn't an option in powerpoint to specify slide size in terms of resolution so according to this article on indezine http://indezine.com/products/powerpoint/books/perfectmedicalpres02.html to get a screen resolution of my preference I divided 360 and 1476 each by 72 which gives me 5"x 20.5" as the slide size for my ppt. After setting up slide size as per above dimensions, I used sizer (http://brianapps.net) to resize my ppt window to 360x1476 so that when I record I do not get any black bars. But after launching recording there are side black bars visible which camtasia records and brings-inside cam studio with black bars. http://www.flickr.com/photos/55097319@N03/5409597049 My question is that after doing the above and as explained in the following video link why do I still get black bars. http://feedback.techsmith.com/techsmith/topics/eliminate_black_bars_in_your_powerpoint_recordings Is there an option in camtasia to stretch the recording to cover up black bars or any other alternative way I can get rid of those black bars while I get a ppt recorded as per my preferred dimensions. Notes: In the techsmith video above it asks to adjust my desktop screen resolution which my display chipset does not allow me to set. I set up show in powerpoint to be "browsed by an individual(window)". Also signage software only supports swf's and video file formats natively and not ppt, pptx etc. Thanks bhavani.

  Read the article

• How to change the spell checking language in Chromium?

  - by mote

  When write I need spell checking in Danish or English (one at a time, not both at the same time), but changing from one language to the other is not working well for me. Example: Writing an email in English, everything is underlined as misspelled because the spelling language is set to Danish. I then right-click the text field and choose "Spell-checker Options" and set the language to English. But is does not change the language. Only after I try maybe 4-5 times it does. Selecting the text, clicking it, clicking the background, click the text, I have tried it all but I cannot figure out how it works. Sometimes it changes on first try, sometimes I have to do it 6-7 times. Searching brings lots of a known bugs stating that Chromium does not re-check the text after changing the language. But that is not what drives me crazy, for starters being able to change the language in the first try would be nice. It is not a fault in my installation, I have the same problem on 3 computers. Does any know something that I don't?

  Read the article

• Share Firefox/Thnderbird data between W7 and Linux Mint 12 in dual boot computer

  - by Albert

  I've just set up my laptop (where I had running only W7) with a dual boot to run Linux Mint 12 as well. I have a "Data" partition (apart from the required partitions for W7 and Linux) where I store pretty much everything that isn't software installations (music, videos, project files, etc). I seem to be able to access that NTFS partition totally fine from Mint (like I've always done with W7), which is cool because I can access all that stuff regardless of which OS I'm using. I would like to know if it's possible (and how) to go one step further and share programs data between the two OS. One example would be my Firefox and Thunderbird data. For example, in Firefox share my bookmarks (and if I could share history, autocomplete and all that stuff, that would be awesome). In thunderbird, be able to share my mail and configuration, seeing the same inbox, folders, message rules, etc... So if I receive/send an email from W7 and later switch to Mint, I can see that email as it had been received/sent from Mint, and vice versa. Is this even possible? Or am I asking for too much convenience? If it's possible, any clues on how to set it all up?

  Read the article

• Why java -version returning a different version than the one defined in JAVA_HOME?

  - by Shekhar

  I am trying to set JAVA_HOME in Ubuntu OS. I have copied jdk 1.7 in /usr/lib/jvm and set JAVA_HOME in /etc/profile file. Contents of /usr/lib/jvm folder are as follows : shekhar@ubuntu:~$ ls /usr/lib/jvm/ default-java java-1.6.0-openjdk java-6-openjdk java-6-openjdk-i386 jdk1.7.0_01 java-1.5.0-gcj-4.6 java-1.6.0-openjdk-i386 java-6-openjdk-common java-7-openjdk-i386 and last few lines of /etc/profile file are as follows : export JAVA_HOME=/usr/lib/jvm/jdk1.7.0_01 export PATH=$PATH:$JAVA_HOME/bin After finishing all this when I run java -version command I get following output : shekhar@ubuntu:~$ java -version java version "1.6.0_24" OpenJDK Runtime Environment (IcedTea6 1.11.4) (6b24-1.11.4-1ubuntu0.12.04.1) OpenJDK Server VM (build 20.0-b12, mixed mode) and when I run ls -lah command I get following output : shekhar@ubuntu:~$ ls -lah /usr/bin/java lrwxrwxrwx 1 root root 22 Sep 29 09:58 /usr/bin/java -> /etc/alternatives/java shekhar@ubuntu:~$ ls -lah /etc/alternatives/java lrwxrwxrwx 1 root root 45 Sep 29 09:58 /etc/alternatives/java -> /usr/lib/jvm/java-6-openjdk-i386/jre/bin/java Can anyone please tell me which thing I am missing? Why Ubuntu is still pointing to open jdk and not to my jdk 7? PS : I have seen this similar question and its answers but that question is related to Windows OS and not for Ubuntu so I am reposting this similar question for Ubuntu.

  Read the article

• iptables to block non-VPN-traffic if not through tun0

  - by dacrow

  I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

  Read the article

• Permissions nightmare - tried all I know

  - by Ben

  Working on a new client's dev site, which is a wordpress install on a Plesk box. I have SSH root access, and FTP access through a separate account. What I've done so far Initially I couldn't make any changes to any files at all. The permissions on all the template files looked a little screwy (644), so I figured change them to allow group, and add myself to the group: CHMOD Recursive on the theme folder to set everything to 664 Quickly realised I'd broken it, set the folders to 755, kept files as 664 Ownership on all files is a mixture of root:root and 500:500 (there is no user nor group with the ID of 500 on the server). Added myself to the group 'root' so I could modify the files too The Problem This worked OK, in terms of being able to edit the existing files, so I began working. However, I can't upload to the directory, even having run CHOWN -R root:root templatefolder/ and being in the root group. I feel like I must be missing something obvious, and it's doing my head in. Questions: Files in the install owned by 500 with group 500 - I've looked in /etc/group and /etc/passwd and there is no user nor group with this ID. Is that left over from another developer's setup or the previous server (they moved recently)? Is being in the 'root' group enough, or do I need to own the theme folder as 'myftpuser' in order to upload and create new files? Like I say, I have edit access, so I got myself this far. I'm now questioning what to do next!

  Read the article

• Juniper SSG 5 VPN

  - by Ethabelle

  I have a host who set up our Juniper SSG 5 VPN with Firmware version-6.2.0r5.0 I've been trying to set up VPN on it using this guide: http://kb.juniper.net/InfoCenter/index?page=content&id=KB4094 I've followed the steps and on my Mac, whenever I try to connect using L2TP over IPSec I get the following error; Summary of Steps: Create User (give them L2TP auth ability), Create Group, Place User in Group, Create VPN Gateway, Create VPN, create IP Pool, change default L2TP settings, create Untrust Trust Policy. The L2TP-VPN server did not respond. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I looked in my Firewall's logs, but I don't even see anything under Reports Logs Events. I'm.. obviously missing something, I just don't know what I'm missing at this point. I'm just starting networking and this is sort of Step 101 and I'm getting annoyed and just want to throw up OpenVPN, but I've read that has problems with Juniper Firewalls. Hooray.

  Read the article

• 403.4 won't redirect in IE7

  - by Jeremy Morgan

  I have a secured folder that requires SSL. I have set it up in IIS(6) to require SSL. We don't want the visitors to be greeted with the "must be secure connection" error, so I have modified the 403.4 error page to contain the following: function redirectToHttps() { var httpURL = window.location.hostname+window.location.pathname; var httpsURL = "https://" + httpURL ; window.location = httpsURL ; } redirectToHttps(); And this solution works great for every browser, but IE7. On any other browser, if you type in http://www.mysite.com/securedfolder it will automatically redirect you to https://www.mysite.com/securedfolder with no message or anything (the intended action). But in Internet Explorer 7 ONLY it will bring up a page that says The website declined to show this webpage Most Likely Causes: This website requires you to log in This is something we don't want of course. I have verified that javascript is enabled, and the security settings have no effect, even when I set them to the lowest level I get the same error. I'm wondering, has anyone else seen this before?

  Read the article

• Can I get a domain controller not to act as DNS for the members?

  - by rsw

  Hi, Let me try to explain my current setup. I have one linux machine acting as DHCP and DNS (dhcpd3 and bind) in my network. This works fine, all computers I hook up to the network gets an IP address and proper DNS servers set. Let's call it 10.12.0.10 However, we also have a Windows Server 2003 Domain Controller in our network to which we add our Windows computers (running XP), let's call it 10.12.0.20. I noticed that when I run 'nslookup' on one of the windows machines, it says that the primary DNS is 10.12.0.20. This have not been much of a problem since: The Windows clients are stationary The Windows server in itself point out my real DHCP/DNS, since I can reach everything specified in it However, this turns out to be a problem when we use Laptops. They connect to the domain here and gets a DNS server, but when the user travels or connect the computer from home, we hit a problem. They are connected to their internet, but their DNS is 10.12.0.20 which they can't reach since they're at home and not at the office network. I solved this by removing the register key called "NameServer" with the value 10.12.0.20, but it gets set again whenever they logon to the domain the next time (when they get back to the office). Can I somehow make the computers take whatever DNS server they are handed when connecting to the internet or a home network, instead of always trying to reach the Domain Controller?

  Read the article

• How do I install mod_dav_svn module on an Apache / MAMP server?

  - by fettereddingoskidney

  How do I install additional modules into my server configuration? Currently all of the other modules are installed in /Applications/MAMP/Library/modules...and I see that they are mod_*.so source files, but I cannot seem to get mine to end up here... :? I am trying to set up an SVN repository and use my Apache (MAMP) server to serve the repository. I am using the subversion installation that came (pre-installed?) on Mac OS X 10.5. The repository is working, but I cannot access it remotely through my MAMP server using a client program (Dreamweaver CS5). When I try, I get an error from Dreamweaver, saying: Cannot connect to host xxx: Connection refused. This, I believe, is because I have not properly configured my Apache server to serve the svn repository. So, I added the following lines to my httpd.conf file: <Location /subversion> DAV svn SVNPath /Applications/MAMP/htdocs/svn/ AuthType Basic AuthName "Subversion repository" AuthUserFile /applications/mamp/htdocs/.htpasswd Require ServerAdmin </Location> Restarted the server with the command $ /Applications/MAMP/Library/bin/apachectl -k restart I used this path because otherwise the default apachectl path is set to /usr/sbin/apachectl, which is the location of the pre-installed command on Mac OS X, since the OS comes packaged with a built-in Apache server. And I get the error: Syntax error on line 1153 of /Applications/MAMP/conf/apache/httpd.conf: Unknown DAV provider: svn I checked the upper portion of httpd.conf and see that dav_module (mod_dav.so) is loaded and is in fact in my the modules directory of my server. However, mod_dav_svn is not installed in that directory nor is it in the LoadModule portion of httpd.conf. So I need to install it, right? I have tried installing modules into my MAMP server before but was never successful...because I don't know how to do it. Can someone please walk me through how to install that module? Thanks for your time!

  Read the article

• SQL Server 2008 Bring Database Online trying to open a file from a drive that doesn't exist

  - by Nai

  This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have domain keys and active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas?

  Read the article

• Networking 2 Virtual PC with one VPC as DHCP server

  - by vivek

  My host OS is Win XP Professional. The host has a real network connection via DSL and I created a second network connection using Microsoft Loopback Adapter. Internet connection sharing is enabled. The Microsoft Loopback adapter has a IP address of 192.168.0.1. I have 1 Virtual PC which has Windows Server 2003. I have setup the network connection on this VPC to use Microsoft Loopback Adapter. I setup this VPC to be the Domain Controller , DNS Server and DHCP Server. I set this to a static IP address 192.168.0.2 (on the same subnet as the MS Loopback adapter) I have a second Virtual PC which also has Windows Server 2003. The network connection on this VPC is set to "Local Only". I want this VPC to get its IP address from the 1st VPC on which I setup as a DHCP server. What i want is the 2 VPC should be in a network with one of the VPC acting as the domain controller, DNS Server and DHCP server. The second VPC shoud get its IP address from the 1st VPC. It should be a part of the domain of the 1st VPC. When i tried to make the second VPC get the IP address from the first VPC I am not succeeding. Can somebody post some suggestions on how to go about this ?

  Read the article

• Issue with multiple bridging for KVM hosts

  - by Henry-Nicolas Tourneur

  I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes not. I don't know if my bridging paramateres are correct, could you check ? or if there is anything wrong ... Please also note that interface on guest doesn't flap and that I got not logs on my host. Of course forwarding is enabled. iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.128 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.128 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.240 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.240

  Read the article

• CloudFront for dynamic content CDN

  - by Elad Lachmi

  I would like to use CF as a CDN for my entire site, including static and dynamic content. I have been using CF for static content for a while and I am very happy with the results. I am now doing POC of putting the web server completely behind CF. For the dynamic content I created a new distribution and set the origin to be my web server. Right now I'm looking to test the solution, so I have the web server on the original domain and the CF distribution on the amazon domain. This works with the exception of HTTPS urls and POST requests. For HTTPS requests, I see the requests are forwarded to the original site domain for now, but how will CF handle them when I move the distribution to the www cname? What configuration changes should I make so that CF forwards HTTPS requests to the origin? For POST requests, I want the post to be made to the origin server. Can I set this up in CF? Finally, the site has membership. Can I configure CF to pull all content from the origin if the user is logged in? Sorry for the long question. I'm a little lost and documentation for dynamic CF is still kind of scarce. Thank you!

  Read the article

• Apache serving empty gzip with assets produced by Rails Asset Pipeline

  - by PizzaPill

  I followed the steps described on the blogpost The Asset Pipeline, from development to production and tweaked them to my environment. The two important files are: /etc/apache/site-available/example.com <VirtualHost *:80> ServerName example.com ServerAlias www.example.com DocumentRoot "/var/www/sites/example.com/current/public" ErrorLog "/var/log/apache2/example.com-error_log" CustomLog "/var/log/apache2/example.com-access_log" common <Directory "/var/www/sites/example.com/current/public"> Options All AllowOverride All Order allow,deny Allow from all </Directory> <Directory "/var/www/sites/example.com/current/public/assets"> AllowOverride All </Directory> <LocationMatch "^/assets/.*$"> Header unset Last-Modified Header unset ETag FileETag none ExpiresActive On ExpiresDefault "access plus 1 year" </LocationMatch> RewriteEngine On # Remove the www RewriteCond %{HTTP_HOST} ^www.example.com$ [NC] RewriteRule ^(.*)$ http://example.com/$1 [R=301,L] </VirtualHost> /var/www/sites/example.com/shared/assets/.htaccess RewriteEngine on RewriteCond %{HTTP:Accept-Encoding} \b(x-)?gzip\b RewriteCond %{REQUEST_FILENAME}.gz -s RewriteRule ^(.+) $1.gz [L] <FilesMatch \.css\.gz$> ForceType text/css Header set Content-Encoding gzip </FilesMatch> <FilesMatch \.js\.gz$> ForceType text/javascript Header set Content-Encoding gzip </FilesMatch> But apache seems to send empty gzip files because the testsite looses all styles and firebug doesnt find any content for the css files. Altough if I call the assets-path directly I get some gibberish that looks like binary data. If I move the htaccess-file everything is back to normal. How could I find out where/what went wrong or do you have any suggestions what error I made? > apache2 -v System: Server version: Apache/2.2.14 (Ubuntu) Server built: Mar 5 2012 16:42:17 > uname -a Linux node0 2.6.18-028stab094.3 #1 SMP Thu Sep 22 12:47:37 MSD 2011 x86_64 GNU/Linux

  Read the article

• Keep permalinks in Wordpress

  - by Remus Rigo

  Is there any way to set my permalinks to keep their exact link. If I have a post like this one http://blog.rigo.ro/?p=11, then I would like that every time I edit the post to keep this link. I have installed the Revision Control plugin and I set it to do not keep revisions. Any ideea how to do this? I want to keep this format of links. Edit: I took a look again, the permalinks keep their links, but every time I edit it adds a new version to the database and the next post will have a higher number. If I edit my current post for 3 times (blog.rigo.ro/?p=11) the next post will be blog.rigo.ro/?p=14. Now, my question is how can I keep all my post and edits clean, one post/more edits = one entry in the database, so if I have. 10 post on my site and I edit them, I would like that my permalinks to be from 1 to 10. PS: I don't want to edit my database manually, is there any plugin to do this?

  Read the article

• Folder redirection GPO doesn't seem to be working

  - by homli322

  I've been trying to set up roaming profiles and folder redirection, but have hit a bit of a snag with the latter. This is exactly what I've done so far: (I have OU permissions and GPO permissions over my division's OU.) Created a group called Roaming-Users in the OU 'Groups' Added a single user (testuser) to the group Using the Group Policy Management tool (via RSAT on Windows 7) I right-clicked on the Groups OU and selected 'Create a GPO in this domain, and Link it here' Added my 'Roaming-Users' group to the Security Filtering section of the policy. Added the Folder Redirection option, specifically for Documents. It is set to redirect to: \myserver\Homes$\%USERNAME%\Documents (Homes$ exists and is sharing-enabled). Right-clicked on the policy under the Groups OU and checked Enforced. Logged into a machine as testuser successfully. Created a simple text file, saved some gibberish, logged off. Remoted into the server with Homes$ on it, noticed that the directory Homes$\testuser was created, but was empty. No text file to be found. From what I've read, I did everything I aught to...but I can't quite figure out the issue. I had no errors when I logged off about syncing issues (offline files is enabled) or anything, so I can only imagine my file should have ended up up on the share. Any ideas? EDIT: Using gpresult /R, I confirmed the user is in fact part of the Roaming-Users group, but does not have the policy applied, if that helps. EDIT 2: Apparently you can't apply GPOs to groups...so I applied to users and used the same security filter to limit it to my test user. Nothing happens as far as redirection goes, but I now have the following error in the event log: Folder redirection policy application has been delayed until the next logon because the group policy logon optimization is in effect

  Read the article

< Previous Page | 698 699 700 701 702 703 704 705 706 707 708 709  | Next Page >