Search Results

Search found 19471 results on 779 pages for 'network troubleshooting'.

Page 702/779 | < Previous Page | 698 699 700 701 702 703 704 705 706 707 708 709  | Next Page >

  • Consulting: Organizing site/environment documentation for customers?

    - by ewwhite
    Over time, I've taken on consulting and contract engineering work for various clients. More recently, customers are asking for certain types of documentation. These are small businesses and typically do not have dedicated technical staff. Within a single company, Wiki/Confluence/Sharepoint, etc. all make sense as a central repository for documentation and environment information. I struggle with finding a consistent method to deliver the following information to discrete customers. I'm shooting for a process that's more portable, secure and elegant than a simple spreadsheet or the dreaded binder full of outdated information. Important IP addresses, DHCP scope, etc. Network diagram (if needed). Administrative usernames and passwords and management URLs. Software license keys. Support contracts and warranty information. Vendor support contacts and instructions. I know there are other consultants here. Any suggestions or tips on maintaining documentation across multiple environments in a customer-friendly format? How do you do it?

    Read the article

  • SSH connection times out unless I tunnel in from a different server-

    - by rm-vanda
    OK, so this just started last week - Whenever we try to connect to our server via ssh (we use sftp, as well) - The connection times out. However, when you ssh to any other server and then ssh into the machine - it works flawlessly. Now, the mindblowing thing is that sometimes the ssh connection will succeed. Moments ago, I tried it from another machine, and then my own, and it worked - only to time out the next go around. Last week, simply restarting the ssh daemon worked, but this week, no such luck. I even went in and changed: /etc/hosts.allow ALL : ALL and /etc/hosts.deny is blank. The firewall config hasn't changed - but I even disabled the firewall to see if that would work - It did, for a moment - before cutting off, again. (ufw is set to "ALLOW" not "LIMIT") When I try SSH'ing in from my phone -- it works, fine -- So, it seems the problem is with our ISP/router/gateway - However, I see no log in the router/gateway that says its blocking our connections - And that wouldn't explain why we can SSH into any other server -- except for this one - from our network --- I truly appreciate any insight that anyone may have on this matter -

    Read the article

  • Server-side SSH jump hosts

    - by Dan Sosedoff
    Trying to figure out server side SSH jump hosts logic. Current network schema: [Client] <--> [Server A: hostname: a.com] <--> [Server B] [Client] <--> [Server A: hostname: b.com] <--> [Server C] Server A responds to both DNS records. Possible flow: Client opens a ssh connection with ssh [email protected]. Server A accepts it and should automatically jump user onto Server B with ssh user2@server_b.com. Client opens a ssh connection with ssh [email protected]. Server A accepts it and should automatically just user onto Server C with ssh user2@server_c.com. In other words, client should be able to connect to the target without performing any local configuration, assuming that we have a stock ssh config. The problem with ssh jumps is that user has to define hosts in local ~/.ssh/config file, which is not acceptable in my case. It needs to be a default sshd behavior. Im aware that you can define a custom command ~/.ssh/authorized_keys on server, but i dont think there is a way to properly detect source hostname where user tries to connect. It is possible at all ?

    Read the article

  • Automatic o/s reset on a dedicated internet browsing Windows 7 pc.

    - by camelCase
    I have just purchased a new Acer Revo nettop PC for dedicated internet browsing. It will be the only pc on a home network. My original plan was to install one virtual PC for family browsing, another for remote web based server administration and ban browser use from the host Windows 7 o/s. The idea was that I could recover to a fresh VHD image once a week to eliminate any build up of malware inside the browser VMs. However now I am looking for alternative solutions since the Intel Atom cpu does not have hardware VT support which Windows Virtual PC requires. Would it be possible to engineer some type of routine overnight host o/s wipe and recovery? I guess cyber cafes do something like this? The only user data that would need to be retained across a recovery would be browser bookmarks but these could be exported to remote service. Edit 1: I am thinking the o/s reset could be done via some disk image recovery process. Edit 2: Just had a brainwave. Routine browsing could be done via the new Google Chrome O/S. I have just seen a video of the Google Chrome o/s booting off a usb pen drive in seconds.

    Read the article

  • Mesh Networked servers via vpn

    - by microspino
    I got a design idea and I would like to have some advice from SF about It. I have 5 customers with small real-estate databases. I've built for them a desktop app and now they would like to merge their database to share their data. I don't want to centralize everything in one place nor I want to do maintenance for servers. They told me also, that all of them in their offices, have little servers and maintenance guys available. Although everything seems suitable for web application, I had the idea to experiment something new: Any customer small-server wild be connected to the others in a sort of mesh network without a single point of failure and through VPNs. If one of the servers went down the customers could still connect to their databases from one of the other mesh networked servers instead of from the local one that is down. During normal operations all the servers sync the db with the others through VPNs. I can accept a half-day timing window of NON synched data, in other words, since I don't need real time synchronization, the server don't have to always stay in synch. I can migrate my data over to other Non-Sql technologies like CouchDB or Redis or whatever you suggest. As you can see I don't have a lot of constraints and although I could go with a web application I would like to delegate and decentralize support, data-privacy and management, as more as I can to my customers offices. Is that a crazy idea? Do you know If something similar exist? Which technology would you suggest?

    Read the article

  • iptables: How to combine DNAT and SNAT to use a secondary IP address?

    - by Que_273
    There are lots of questions on here about iptables DNAT/SNAT setups but I haven't found one that solves my current problem. I have services bound to the IP address of eth0 (e.g. 192.168.0.20) and I also have a IP address on eth0:0 (192.168.0.40) which is shared with another server. Only one server is active, so this alias interface comes and goes depending on which server is active. In order to get traffic accepted by the service a DNAT rule is used to change the destination IP. iptables -t nat -A PREROUTING -d 192.168.0.40 -p udp --dport 7100 -j DNAT --to-destination 192.168.0.20 I also wish all outbound traffic from this service to appear to come from the shared IP, so that return responses will work in the event of a active-standby failover. iptables -t nat -A POSTROUTING -p udp --sport 7100 -j SNAT --to-source 192.168.0.40 My problem is that the SNAT rule is not always run. Inbound traffic causes a connection tracking entry like this. [root]# conntrack -L -p udp udp 17 170 src=192.168.0.185 dst=192.168.0.40 sport=7100 dport=7100 src=192.168.0.20 dst=192.168.0.185 sport=7100 dport=7100 [ASSURED] mark=0 secmark=0 use=2 which means the POSTROUTING chain is not run and outbound traffic leaves with the real IP address as the source. I am thinking I can set up a NOTRACK rule in the raw table to prevent conntracking for this port number, but is there a better or more efficient way to make this work? Edit - Alternative question: Is there a way (in CentOS/Linux) to have an interface that can be bound to but not used, such that it can be attached to the network or detached when a shared IP address is swapped between servers?

    Read the article

  • C# sends SQL data 4 times less from one box than from another

    - by Bobb
    W2003, .NET 3.5, SQL 2008 I have prod and UAT app servers deployed in 2 different data centres. I have a C# app which reads text file, parse the text and sends the data to the SQL in bulk. SQL server is in US and the app servers are in London (but in different places). All POPs have dedicated network connections. There is no public internet involved. When the app runs on UAT server I can see in Perfmon that the Send byte/sec is x4 higher than from production server. My estimate is that one server outputs at 1 MB/s and the other at 250 KB/s rate. My suspicion immediately is that there is a router on one of the DCs which shapes traffic or does QoS limitation on traffice from London to US. However support and Windows team and networkig team all are saying that there are no differences in neither networking config on the 2 DCs nor NIC config on the 2 app server... How to find out why is the networking bottlneck is 4 times tighter in one place than in the other? What can I do about it?

    Read the article

  • Hybrid Exchange Online setup with on premise public folders, certificate issues?

    - by exxoid
    We have a Hybrid Exchange setup with Exchange Online (v15 tenant) and Exchange 2010 on premise. The hybrid configuration for the most part is working, what I am having an issue with is getting public folders to work for cloud users. I followed the official documentation here (http://technet.microsoft.com/en-us/library/dn249373(v=exchg.150).aspx) and it kind of works. When I am accessing Outlook on a public wifi I am able to bring up the cloud mailboxes and on premise public folders show up in Outlook. When I am accessing email via Outlook as a cloud user on the same LAN as the on premise exchange, the cloud user makes the outlook.com connection for live/ad/archive mailbox but fails to create a proxy connection for the on premise public folders. The error I get is a certificate mismatch, it seems that when a user on the LAN accesses Outlook/Exchange it is using a different certificate vs. when Outlook is launched on a WiFi network. When I look at the Outlook connection information, I see the connection to outlook.com for ad/live/archive mailbox but no entry for public folder connection. Our on premise Exchange is 2010 SP3 with latest CUs. The client is a domain joined laptop with Windows 7 and Office 2010 SP2, latest windows updates applied. Our infrastructure has a working ADFS 3 and DirSync setup for Office 365. My question then is, what do I need to do to make sure that the Cloud user launching Outlook on the LAN uses the proper certificate (the wildcard 3rd party cert.. vs. the self signed certificate which it looks like it may be using during the connection attempt).

    Read the article

  • Single Sign On 802.1x Wireless - saying “Connecting to <SSID>”, hangs for 10 seconds, fails with “Unable to connect to <SSID>, Logging on…”.

    - by Phaedrus
    We are implementing WiFi on Windows 7 machines in our corporate environment. Machines should be able to log into the domain by WiFi as the Machine (Pre-Logon), and as the User (Post-Logon). We have everything working correctly except for 2 things: 1) Sometimes the login scripts don't run 2) The user VLAN is sometimes different than the machine vlan, and no DHCP renew occurs after user logon. I am clear that both these problems should be fixable by using the "Single Sign On" Option under the 802.1x Wireless Vista GPO, and setting the wireless to connect immediately before user logon and also by enabling "This network uses different VLAN for authentication with machine and user credentials" If I enable these GPO settings in a lab, the computer does authenticate & gets WIFI before the user logs on, so when the login box is displayed, it says “Windows will try to connect to ”, even though it is already connected (which should be ok?). Enter the user credentials and it goes to a screen saying “Connecting to ”, hangs for 10 seconds, fails with “Unable to connect to , Logging on…”. Desktop fires up and then the user re-authenticates with no problem as himself instead of the machine, but by that point, we defeat the point of the WiFi SSO “before user logon”. Also by that point, no DHCP renew seems to occur, and the user is still stuck with the wrong IP address for the new VLAN. When the “Connecting to ” screen comes up, there’s no indication on the AP or the Radius server that anything whatsoever is happening after credentials are entered until after the domain logon. Also with this policy enabled, sometimes windows hangs on a black screen indefinitely until I disable the Wireless NIC, so something is knackered for sure. What have I missed? Suggestions are much appreciated... /P

    Read the article

  • 100% uptime for a web application

    - by Chris Lively
    We received an interesting "requirement" from a client today. They want 100% uptime with off-site failover on a web application. From our web application's viewpoint, this isn't an issue. It was designed to be able to scale out across multiple database servers, etc. However, from a networking issue I just can't seem to figure out how to make it work. In a nutshell, the application will live on servers within the client's network. It is accessed by both internal and external people. They want us to maintain an off-site copy of the system that in the event of a serious failure at their premises would immediately pick up and take over. Now we know there is absolutely no way to resolve it for internal people (carrier pigeon?), but they want the external users to not even notice. Quite frankly, I haven't the foggiest idea of how this might be possible. It seems that if they lose Internet connectivity then we would have to do a DNS change to forward traffic to the external machines... Which, of course, takes time. Ideas? UPDATE I had a discussion with the client today and they clarified on the issue. They stuck by the 100% number, saying the application should stay active even in the event of a flood. However, that requirement only kicks in if we host it for them. They said they would handle the uptime requirement if the application lives entirely on their servers. You can guess my response.

    Read the article

  • Setting up apache vhost for Icinga

    - by DKNUCKLES
    It's been a while since I've worked with Apache so please be kind - I'm also aware of this question but it hasn't been much help to me. I'd like to set up a simple vHost w/ Apache for my Icinga instance. Icinga is up and running and I can access it from x.x.x.x/icinga, however would like to be able to access it externally as well as internally. I have set up the /etc/hosts file and the following is my barebones vhost statement in httpd.conf <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /usr/share/icinga ServerName icinga.domain.com ErrorLog logs/icinga.com-error_log CustomLog logs/dummy-host.example.com-access_log common </VirtualHost> I also have the following in my .htaccess file <Directory> Allow From All Satisfy Any </Directory> An entry has been made for the instance in the Windows DNS server on my network, however when I try to access the site by URL I am greeted with Internal Server Error. Reviewing the /var/log/icinga.com-error_log I see the following entry. [Thu Dec 13 16:04:39 2012] [alert] [client 10.0.0.1] /usr/share/icinga/.htaccess: <Directory not allowed here Can someone help me spot the error of my ways?

    Read the article

  • Microsoft Deployment Toolkit 2012 Error

    - by Jacob Schaer
    I just started with MDT2012 recently in hopes of eventually getting away with using Ghost to deploy all of our department computers. When I test deploy in VirtualBox, it deploys the OS properly, but stops because of a network driver failure (it gets the "could not allocate resources" issue). On physical hardware (Latitude E6500, Optiplex 980, and an older Latitude) it gets through the multicast and stops immediately after with: "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information" I've looked at the logs and never see anything really of note. Originally I was using DriverPacks from DriverPacks.net, but thinking it was a driver issue, I switched over to using Dell's cab driver packs. Still the same issue. I check and it did the HDD is all fine - it was properly partitioned, set to bootable, and was loaded with all the proper OS installer files. I'm using a flash drive to do the install - when I make changes to the deployment share I rebuild and copy the ISO to the drive, then use YUMI multiboot to start the ISO (probably irrelevant).

    Read the article

  • Server 2008 RAID 5 Write Speeds

    - by Solipsism
    I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

    Read the article

  • SFTP, SCP, Secure Webdav: which is the most suitable ?

    - by Xavier Maillard
    Hi, currently, I am hosting a webdav share setup in order to store files I need anywhere I am. It is available via HTTPS. Things are that I do not need all the HTTP machinery -i.e. my nginx http server is only there for this webdav folder. I am not sure I made the best choice. My requirements on the client side are: secured transfers mountable as a network drive at work with 'near realtime sync' usable for any OS I could use (including my mobile (android)) At first, I chose webdav since it would pass through my work proxy (which refuses all that is not on HTTP/S (port 80 or 443)). Today, I am not satisfied with the setup and even if nginx memory footprint is pretty small, its webdav support is not really "clean" and full. What would you recommend between SFTP, SCP and the current webdav solution ? I think SFTP is the closest solution but I still have to find out how to pass through my proxy ;) SCP seems quite limited as I read about it (only file transfers if I read right). Cheers

    Read the article

  • Same native and tagged vlan possible on Redhat?

    - by Chris Phillips
    Hi guys and gals, I'm looking at implementing a systems using a number of tagged and a native vlan connected to a server over a a/p bonded interface. The untagged vlan is for physical machine access, the tagged vlans are connected to bridges and then to QEMU VM's inside the machine. Hopefully this plan is fine, but I'm trying to implement a crippled version of this in a dev environment due to a lack of underlying network config in this location where I just have the same single vlan delivered to the machine on a tag AND plain. I'm nto clear if this is going to work (and that I should just be confident that it will work using different vlans) as I'm seeing odd things like a vm is arping out over the vlan out to the core switch, but the arp reply is coming back on the untagged interface. Now an ARP reply is unicast right? So it's a deliberate thing to send the ARP response on the untagged interface, and not a case that a broadcast response isn't being passed on the tagged side... i.e. there's some underlying logic pushing it that way. Something about the MACs somehow? This is on a CentOS 5.5 machine, vlan's from vconfig. (I've seen reference to the Linux mac-vlan project work, but that's not available here by default.) so 1) Should having the SAME vlan tagged and untagged work? 2) Will different tagged vlans to the untagged interface work nice and easily?

    Read the article

  • Trobleshooting extremely slow opening times in Win7 for documents on Win2k8 server

    - by Mazupan
    Hello. It's hard even to describe my problem. It seems there's only problem with extreme slow openings (up to 10 minutes) on Windows 7 (on XP things works fine) for files that are stored on Windows Server 2008. And now what I discovered up till now. If I open (some files, not all, not allways) .doc and .xls files with doubleclicking it takes up to 10 minutes to finaly open the file. In that time, file seems to be locked for all other users. If I cancel opening, file remains locked for some time. Owner on that files is the one who last wrote changes in them. If I change the owner to larger group, which I am member of file gets opened super fast. When opened file can be saved normaly and fast. That file reopens fast. One other user reports that there is only problem when opening the files for the first time in a day. When he openes first file he has no problems with other files at all (or so he says). He also states that when accessing files from home via VPN he has no such problems with files. And now: anybody has a clue where to start looking? I suppose that is misconfiguration problem. But where? File system? Permissions? DFS? VMWare network config? My setup is as follows: Physical server: HP Prolian ML350 G6 Virtual host: VMWare ESXi 4 Guest: Windows Server 2008 Standard Files are accessed via DFS shares. Please help me. Thanks. Mazupan

    Read the article

  • dhcp3-server (dhcpd) is tampering with host NIC

    - by user61000
    Hi all, I have a debian box that is serving as a router (using iptables NAT). When first turned on, everything works fine for a few minutes. Then the dhcp server assigns an IP (other than 192.168.0.1) to its' host NIC, eth0. This is NOT what I want. I just want dhcp3-server to listen on eth0, not assign it an IP, and changes the kernel routing table. This of course ruins the NAT capablities of the box. How can I tell the dhcp3-server NOT to do this? Thanks Before dhcp3-server tampers with eth0, the IP is 192.168.0.1, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 173.33.220.1 eth1 After dhcp3-server tampers with eth0, the IP is 192.168.0.3, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 192.168.0.1 eth0 default 173.33.220.1 eth1 SETUP Outbound NIC is eth1 Internal NIC is eth0 /etc/network/interfaces ... iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 /etc/default/dhcp3-server INTERFACES="eth0"

    Read the article

  • Apps won't start after vanilla reboot

    - by Daniel R Hicks
    I had Adobe and Norton nagging me to reboot, so I did that -- clicked Reboot from the Start button. Everything seemed pretty normal as it shut down and came back up, but once up a bunch of apps won't start. The first one I noticed was Firefox. It would flash the disk light normally, but never appear on the screen. Then I tried to bring up an OpenOffice Calc window and same thing. I tried to bring up MS Word, and the splash screen appeared, but never the main screen, and the splash screen just sat there, with a swirly over it. But I tried Solitaire, Notepad++, Paint, and several others, and they popped up just fine. And I'm typing this from IE 8, which, if anything, came up faster than usual. When I try to open up "Network and Sharing Center" the window appears, but nothing appears in it, and eventually it's tagged "not responding". When I kill that window I get (after a delay) "Windows Explorer is not responding", and when I say "OK" the screen resets. I tried rebooting again, and no joy -- same as before. Have done nothing particularly strange on this box, and it's not generally at significant risk for malware. I haven't installed anything new other than the afore-mentioned updates. One other thing: Several minutes after rebooting I get the message "Error: Unable to start Bluetooth Stack Service." The Bluetooth radio is turned on, and I rarely have anything Bluetooth attached, and I don't recall that I've ever seen this message before. Added: Looking at Event Viewer, I'm getting a lot of "The description for Event ID 1 from source xxx cannot be found." Is there any significance to this? Added: I'm looking at restoring from backup, but the procedure is, at best, unclear. Is it sufficient to restore from "Backup and Restore Center", or must I restore from the restore DVD first?

    Read the article

  • Gigabyte H55N-USB3: No video on HDMI

    - by newt
    I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

    Read the article

  • How do I cancel windows server 2003 repair install?

    - by Kilgore2k
    System: Windows 2003 Server Enterprise Scenario: NTDS db is corrupt and all attempts to fix with esentutl fail. Ran chkdsk which seemed to repair disk error and give access to the ntds.dit file but still esentutl fails. (Attached the drive to a different server to run the esentutl) Error: Access to source database '[path to copy of]/ntds.dit' failed with Jet error -1022. Operation terminated with error -1022 (JET_errDiskIO, Disk IO error) after 0.170 seconds. This error occurs on any disk I cpoy the files to including original location in C:\WINDOWS\NTDS\ Now enter the "Stupid!" and "what was I thinking!?" part (must be the late hour...) Stupid: No updated backup - after using a backup I get a network password error in the lsass error. what was I thinking!?: Started the install repair from the original CD but the install fails since the AD fails to start. Now I cant boot into any mode (safe mode, AD restore etc) nor complete the repair install. I would really like to avoid a fresh install since I have the Exchange server on this DC and would rather migrate to a new server than have to start from scratch. Thanks!

    Read the article

  • Use GRUB/GRUB2 to PXE boot OS image

    - by Jack
    Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

    Read the article

  • Watchguard Firebox "split" fibre optic line into 2 interfaces

    - by fRAiLtY-
    We have a requirement on our Watchguard Firebox XTM505 to be able to split our incoming external interface, in this case a fibre optic dedicated leased line, 100/100. We use the line in our office of approx 30 machines however we also re-sell to an external company who utilise it to provide wireless internet solutions to the public. The current infrastructure is as follows: Data in (Leased Line) - Juniper SRX210 managed by ISP - 1 cable out into unmanaged Netgear switch - 1 cable into our firewall and office network, 1 cable to our external providers core router managed by them. We have been informed that having the unmanaged switch in the position it is poses a security risk and that a good option would be to get our Watchguard Firewall to perform the split, by separating our office onto a trusted interface, and by "passing through" the external line to their managed router. It is alleged that the Watchguard is capable of doing this and also rate limiting the interfaces, i.e. 20mbps for the trusted interface and 80mbps for the "pass-through", however Watchguard technical support don't seem to be able to understand what we're trying to achieve. Can anyone provide any advice on whether this is possible on a Watchguard device and how or perhaps if there's a better way of achieving this, perhaps with a managed switch instead of unmanaged? Cheers

    Read the article

  • Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

    - by Nils
    I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

    Read the article

  • Sending same email through two different accounts on different domains using Outlook 2010

    - by bot
    I am a programmer and don't have experience in Outlook configurations. Our company has two email domains namely xyz.com and xyz.biz. Each employee has an email id on one of these domains but not both depending on the project they are working on. The problem we are facing is that when a communication email is sent from the Accounts, HR, Admin, etc departments, they need to send the email twice. Once through the xyz.com account to all employees with an email address on xyz.com and once through xyz.biz to all employees with an email address on xyz.biz. I am not sure why they have to send two separate emails but the IT team has directed all departments to do so as there is no other solution according to them. Even though two different groups have been created, sending an email to employees in a group of xyz.biz from xyz.com does not seem to work. I want to know if Outlook provides a feature such that we can configure some kind of rules to send an email through an id on xyz.com to all users on xyz.com and the same email gets sent automatically to users on xyz.biz through an id on xyz.biz. The only technical details I know is that we are using Exchange 2003 and the IT team claims that this is a limitation causing the problem. Edit: Our company is split into two main divisions depending on the type of projects. I am pretty sure I use domain XYZ wheras the employees in the other division use the doman ABC to log in into the windows machine or outlook itself. Also, employees in domain XYZ can access the machines on the network in domain ABC but not the other way around

    Read the article

  • Packet flooding while configuring a Debian L2TP/IPSec client?

    - by Joseph B.
    I'm currently at my wits end trying to configure an L2TP over IPSec VPN connection on my Debian using openswan and xl2tp box connecting to a server of unknown configuration. I've managed to successfully establish the connection and everything appears to be working well until I attempt to set the VPN connection as my default route, at which point I see a massive flood of packets simultaneously being transmitted (on the tune of ~1.5 GB in about 2min) until the server drops my connection. Prior to this network traffic on all my interfaces is minimal. According to iftop the majority of this traffic appears to be coming out of port 12, although I can't seem to figure out how to finger a specific process. If I instead just route traffic destined for 74.0.0.0/8 through it I'm able to access Google's servers through the VPN without issue. My xl2tp.conf file is: [lac vpn-nl] lns = example.vpn.com name = myusername pppoptfile = /etc/ppp/options.l2tpd.client My options.l2tpd.client file is: ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1410 mru 1410 usepeerdns lock name myusername password mypassword connect-delay 5000 And my routing table looks like: Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.2.1 * 255.255.255.255 UH 0 0 0 ppp0 10.0.50.0 * 255.255.255.0 U 0 0 0 eth0 10.50.0.0 * 255.255.0.0 U 0 0 0 eth0 10.0.0.0 * 255.255.0.0 U 0 0 0 eth0 192.168.0.0 * 255.255.0.0 U 0 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default * 0.0.0.0 U 0 0 0 ppp0 I'm seeing absolutely nothing in auth.log and syslog during this time and can't seem to find any other log files it might be writing to. Any suggestions would be appreciated!

    Read the article

< Previous Page | 698 699 700 701 702 703 704 705 706 707 708 709  | Next Page >