Search Results

Search found 20285 results on 812 pages for 'selling software'.

Page 709/812 | < Previous Page | 705 706 707 708 709 710 711 712 713 714 715 716  | Next Page >

• hp DL380 G4 won't boot with disk plugged into front USB

  - by Kev

  We outgrew a few older external USB backup drives, and purchased WD My Passport 1 TB USB 3.0 drives to replace them. When they are plugged into the front of our G4, it will blink forever after the BIOS (which is current, BTW) and never boot, even though the USB disks are not "bootable" per se. Our old drives did not exhibit this behaviour (so I don't think it's this type of issue that I've read about other servers.) The old drives were USB 2.0, but this shouldn't make a difference, AFAICT--the specs say all of the G4's USB ports are the same, 2.0, anyway, so I'm not sure how one port would handle a USB 3.0 device better than another. If we plug the new drives in one of the back slots, it boots fine. What's the cause? My concern is that the front USB port, and possibly the motherboard, might be starting to die. (We are experiencing other strange issues with them, or were initially, like intermittent file permissions errors despite wide-open ACL on these local drives, but some serverfault users have me convinced they may be coincidental software/security related issues.)

  Read the article

• Server stops responding, can't find issue?

  - by Corey W

  I've had a pretty basic server up and running CentOS with webserver/database, and have noticed that it has locked up a few times in the middle of the night. It seems to happen randomly. When it locks up I can ssh in, (although it seems to hang once connected), but can't access cpanel/whm and have to reboot the server to get everything back up. Checking the messages log I see the below like clockwork every 5minutes 1 second, and then it just stops logging anything until I reboot. I can't seem to find any log showing any issue? Is there somewhere I can check to try to figure out what is happening? Could this be caused by CPU being maxed? Nov 17 08:01:35 s1 pure-ftpd: (__cpanel__service__auth__ftpd__Q13SKrtaCJCHjBezTfU8Iqmsi@127.0.0.1) [INFO] Logout. Nov 17 08:06:36 s1 pure-ftpd: ([email protected]) [INFO] New connection from 127.0.0.1 Nov 17 08:06:36 s1 pure-ftpd: ([email protected]) [INFO] __cpanel__service__auth__ftpd__mxidFBSnQXmR0QzqSxlqrXLIH0CmJ0GPh9bZ5V3 is now l ogged in Nov 17 08:06:37 s1 pure-ftpd: (__cpanel__service__auth__ftpd__mxidBDaCgnqSxlqrXLIH0CmJ0GPh9bZ5V3@127.0.0.1) [INFO] Logout. Nov 17 08:11:37 s1 pure-ftpd: ([email protected]) [INFO] New connection from 127.0.0.1 Nov 17 08:11:38 s1 pure-ftpd: ([email protected]) [INFO] __cpanel__service__auth__ftpd__T4B7F71acf1dsdJSeJHdqKNcbOdpzNnN_GttgcM is now l ogged in Nov 17 08:11:38 s1 pure-ftpd: (__cpanel__service__auth__ftpd__T4B7F71acf1KNcbOdpzNnN_GttgcM@127.0.0.1) [INFO] Logout. Nov 17 08:16:38 s1 pure-ftpd: ([email protected]) [INFO] New connection from 127.0.0.1 Nov 17 08:16:38 s1 pure-ftpd: ([email protected]) [INFO] __cpanel__service__auth__ftpd__W5C1RzumtaNwe4cU8Lt1 is now logged in Nov 17 08:16:38 s1 pure-ftpd: ([email protected]) [INFO] Logout. Nov 17 09:10:58 s1 kernel: imklog 4.6.2, log source = /proc/kmsg started. Nov 17 09:10:58 s1 rsyslogd: [origin software="rsyslogd" swVersion="4.6.2" x-pid="1094" x-info="http://www.rsyslog.com"] (re)start Nov 17 09:10:58 s1 kernel: Initializing cgroup subsys cpuset

  Read the article

• can't ssh from mac to windows (running ssh server on cygwin)

  - by Denise

  I set up an ssh server on a fresh windows 7 machine using the latest version of cygwin. Disabled the firewall. I can ssh into it from itself, from a different windows box (using winssh), and from a linux vm. In spite of that, I tried to ssh in from two different macs, and neither would let me! This is the debug output: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 3dbuild [172.18.4.219] port 22. debug1: Connection established. debug1: identity file /Users/Denise/.ssh/identity type -1 debug1: identity file /Users/Denise/.ssh/id_rsa type 1 debug1: identity file /Users/Denise/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5 debug1: match: OpenSSH_5.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '3dbuild' is known and matches the RSA host key. debug1: Found key in /Users/Denise/.ssh/known_hosts:43 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /Users/Denise/.ssh/identity debug1: Offering public key: /Users/Denise/.ssh/id_rsa Connection closed by [ip] It shows the same output, and fails at the same place, whether I have put my public key on the ssh server or not. Any help would be appreciated-- hopefully someone has run into this before?

  Read the article

• Home Server: storage virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on storage management. (I have another question related to the VM/compute instance management). Here my environement and wishes. Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) with 1 250GB system disk and up to 4 HDD (2 TB) for "data" OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine The 4 HDD is going to be a software RAID array, probably RAID 5. storage should be "virtualised/cloudified": easy to extend: if I add a NAS on the network, I can include the NAS space capacity within this storage space as one virtual disk. This can be a NAS, an external HDD or another server. cluster FS or S3 style space or OpenStack block storage? Whatever is easier to manage/maintain and easy to integrate/plug to VM/compute instance. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. Note: the VMs I intend to run on top of this server are one dedicated to backup, one for a "owncloud/dropbox"-like service and perhaps one for media server (hosting video and photos). I'm not sure if traditional VMs or compute instance are the most suitable for this.

  Read the article

• Samsung laptop randomly shuts down

  - by Dmatig

  I've rewritten this question because it turned into an indecipherable mess. I have a Samsung R560 laptop that is overheating, and shutting itself down under load consistantly. Thank you quickcel for reccomending me Speedfan to monitor my temps. Here they are (Load / Idle): (Ignore "Temp1 and Temp2", whatever sensors they are they'd always random, pretty sure they're broke). The load temperature is after just 5 minites of playing Fallout 3 - another 5 minutes and it (the GPU - 9600M GS) consistantly breaches the mid 90's then shuts down, so it's hard to get a good picture of it. I'm looking for some solution or way to decrease these temperatures, because they seem far too high even idle. I've tried: Opening up the case and clearing of all dust with compressed air. Updating drivers for my Graphics card Have purchased and am using a notebook cooler I don't want to: Undervolt / underclock (defeats the point of having a more expensive card) Use lower power / performance settings (again, i might as well have bought something cheaper) Is there anything else i can try (software or inexpensive hardware) that can help me fix this? Has anybody had a Samsung laptop and knows if this can be sorted under my warranty, and the turnaround time of sending it off (UK?)(it has always ran hotter than it should, but now at 6 months old is getting hot enough to power off)

  Read the article

• Preferred mail system/server for a company?

  - by Trevoke

  Say you are responsible for setting up an email solution at a company. Which would be your choice? I know of the following options, but many of them not well: Gordano Mail System Exchange Exim Postfix Qmail Zimbra For having used it a little over two years, I really, really like Gordano Mail System. They offer a whole bunch of things, like calendaring, anti-spam, anti-virus, extremely complete and filterable logging options, aliases, a customizable webmail interface... And their software can be installed on both a Windows or Linux OS. In addition, their support is top-notch, their knowledgebase comprehensive (and, I will admit with a touch of pride, I have contributed, with my questions, to the addition of a few articles in there). Of course, they're not free, which can be a problem, but they're not Exchange, and they do offer pretty much everything that Exchange offers -- which is great if you want to stay away from that, but need all the features. Although, if you need a Blackberry Exchange Server, or something similar, I'm not sure what you should go for. So.. What would your choice be? Why? I've never played with a more DIY email solution, but I'm sure many people here have and wouldn't trade their setup for the world :)

  Read the article

• PTR and A record must match?

  - by somecallmemike

  RFC 1912 Section 2.1 states the following: Make sure your PTR and A records match. For every IP address, there should be a matching PTR record in the in-addr.arpa domain. If a host is multi-homed, (more than one IP address) make sure that all IP addresses have a corresponding PTR record (not just the first one). Failure to have matching PTR and A records can cause loss of Internet services similar to not being registered in the DNS at all. Also, PTR records must point back to a valid A record, not a alias defined by a CNAME. It is highly recommended that you use some software which automates this checking, or generate your DNS data from a database which automatically creates consistent data. This does not make any sense to me, should an ISP keep matching A records for every PTR record? It seems to me that it's only important if the IP address that the PTR record describes is hosting a service that is sensitive to DNS being mismatched (such as email hosting). In that case the forward zone would be configured under a domain name (examples follow the format 'zone - record'): domain.tld -> mail IN A 1.2.3.4 And the PTR record would be configured to match: 3.2.1.in-addr.arpa -> 4 IN PTR mail.domain.tld. Would there be any reason for the ISP to host a forward lookup for an IP address on their network like this?: ispdomain.tld -> broadband-ip-1 IN A 1.2.3.4

  Read the article

• Archive Manager, SQL 2005 and MaxTokenSize high CPU

  - by Tim Alexander

  So, I posted this question a few days ago: Impact of increasing the MaxTokenSize for Kerberos Tickets Since then the thought was to test our settings on two member servers, one with IIS and one without. I setup two GPOs to configure the MaxTokenSize reg setting to 48000 and MaxFieldLength/MaxRequestBytes to 64200 (based on MS KB2020943, these are set at 4/3 * T + 200). The member server seemed to work ok (a devalued tape backup server). The IIS server however has had some strange repercussions. The IIS Sserver host Quest Software Archive Manager (AM) 4.5 that communicates with SQL Server 2005 Enterprise on Server 2003 R2. After the changes all looked good until the SQL Server hit 100% CPU. I have removed the GPOS, removed the reg values and even replaced them with defaults (12000 for token size and can't remember the other one but was in a blog post about the issue in my other post). No change. Bouncing the IIS Server stops the high CPU and a colleague has looked at the SQL server and it is definitely the AM connection taking up the time/work on the SQL server. I haven't changed the reg values on the SQL server or the DCs but am reluctant to do so without understanding why this has happened. I am guessing its to do with the overriding auth and group issue we have but I am not seeing Kerberos errors in either event log. Has anyone seen something similar or does anyone have some tips? Was definitely blindsided by the Kerberos issue and am swimming against the tide to keep things functioning.

  Read the article

• No power save on external hard drive - How to implement?

  - by blastawaythewall

  I recently bought a new 3.5" USB external hard drive which I thought had a power save feature on it, but it turns out that it doesn't. So whether it's being used or not, it spins, which wouldn't be a problem if it wasn't so loud and didn't get really really hot. After doing some research, it seems like what controls this is the enclosure of the hard drive and not the drive itself or the OS (although I suspect that's not entirely true). I attempted to use the "hdparm" utility but it couldn't identify my externals. Just to be clear, I'm defining power save as a hard drive spinning down after a certain time period of not being used (read from/written to). Also, I have other externals that do this, so it's not a problem from my computer. Here's my question: Is there a way to implement a power save-like feature on my hard drive through software, OS settings, or anything else? Here's some details: Running: Windows XP Home SP2 HD Model: Cavalry CAUM-B-OTB 2TB (although the website only lists 1TB max) Inside: Hitachi Deskstar 7K2000 (HDS722020ALA330) (I would link, but new users can only post 1) Thanks in advance.

  Read the article

• Packets being dropped by iptables

  - by Shadyabhi

  I am trying to create a Software Access Point in linux. I followed the blog here. Steps I performed: Started dhcp server on wlan0. Properly configured hostapd.conf Enabled packet forwarding & masquerading. Two commands executed regarding iptables: iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface wlan0 -j ACCEPT I enabled logging on iptables & I get this in everything.log Jun 29 19:42:03 MBP-archlinux kernel: [10480.180356] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=38025 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.389102] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=308 TOS=0x00 PREC=0x00 TTL=52 ID=14732 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK PSH URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.389710] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=14988 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK FIN URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.621118] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=63378 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK FIN URGP=0 I have almost no knowledge of iptables, all I did was through googling. So, can anyone help me in making me understand what wrong is happening here? I have tried running tcpdump on wlan0 & http packets are being sent from wlan0.

  Read the article

• Unable to Use Bluetooth Mighty Mouse or Wireless Keyboard with Boot Camp

  - by Kristopher Johnson

  I have Windows 7 64-bit running on a MacBook Pro in a Boot Camp partition. I am trying to pair with my Bluetooth Mighty Mouse and Apple wireless keyboard under Windows, but whenever I try to do so, here's what happens: While on the Add a device window, I turn on the mouse or press a key on the keyboard, and the mouse or keyboard shows up in the list of available devices. I click the device and then the Next button, and the window displays Connecting to device... Time passes. Eventually, I get this error message: Adding this device to this computer failed Adding the device failed resulting in an unknown error. The reported error code is 0x80070015. Contact your device manufacturer for assistance. I've run Windows Update and Apple Software Update. I've also tried reinstalling the drivers from the Snow Leopard DVD. The mouse and keyboard both work fine when I boot into Mac OS X. FWIW, after many, many repeated tries, I eventually got it to work. I don't know why. So while my problem is solved, I'd still like to get an "answer" as to why trial-and-error seems to be the only approach. The keyboard, in particular, was hard to get set up. A few times, Windows would apparently recognize it and prompt me to enter the pairing code, but then it would time out after a couple of seconds (not long enough to enter the code). Grrrr.

  Read the article

• Problem in accessing Windows shared folder on Ubuntu using terminal

  - by vikramtheone

  Hi Guys, Description I have 2 systems with me, one running on Windows(Host) and one on Ubuntu, both on a LAN. On the Windows(Host) I develop software intended for the Linux system and because the Linux system has little external memory, my idea to overcome this is by making the project folder on the Host side a Shared Folder with full access and access it on Ubuntu over the network. To achieve this, I have installed Samba on Ubuntu, when I go to Places -> Network I can see the shared project folder and I simply mount it. A link appears on the desktop. Next, using Nautilus I open the link and I can access the contents of the shared folder. Problem Even though I mount the shared project folder, I don't see it appearing in the /media or the /mnt folder, as a result of this I don't know what path to use to access this folder, from the terminal. For example: When, I mounted my USB stick, as expected, a link for the device appears on the Desktop and I also see a folder in the media folder. So, similarly, a mounted shared folder should have appeared on the /mnt folder, too. Can anyone suggest what I should do now? There are many posts around, but no solid solution for this problem. Help!!! :) Vikram

  Read the article

• CLOSE_WAIT sockets burst - perhaps because of iptables settings?

  - by Fabrizio Giudici

  I have an Ubuntu 12.04 server virtual box where basically the installed software and configuration are the default ones, plus the installation of a jetty 6 server which servers a few websites. To keep things simple I didn't install apache httpd and used iptables for exposing jetty (which runs on the 8080 port) to the port 80. These are the results of /sbin/iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain POSTROUTING (policy ACCEPT) target prot opt source destination I must confess I have a shallow comprehension of how iptables works, in particular for the different kind of chains. This thing works, but sometimes I have an explosion of sockets that stay permanently in CLOSE_WAIT state. I know about what this state means, but since I didn't write the code that manages servlets (they are handled by jetty) I can't fix the problem by patching my code. Eventually the amount of CLOSE_WAIT sockets builds up and makes the server not responsive, so I have to restart jetty. I've looked around for similar problems wth CLOSE_WAIT, and only found cases related to the programmer's code, or problems with Tomcat, not Jetty. I was wondering whether they could be related to a partially broken iptables configuration (the alternative is a bug in Jetty 6, but I first want to exclude other possible causes). Thanks.

  Read the article

• Optimal video resolution and encoding for recording games for YouTube?

  - by Rookie

  I want to record video from games, therefore I cannot use very large video resolution, but I still want to make the large video view to look as sharp as the original encoded video before upload. I tried to use YouTube's recommended 854x640 resolution, but it wasn't possible with h264 and the encoding software I used (Handbrake) converted it to a width of the nearest multiple of 4, which I think is a limitation of the h264 format. The video I encoded was sharp and fine quality, but when I uploaded it to YouTube, it lost a lot of quality and the preferred large video view looks almost as bad as a 320p video. I tried to wait a few days but it never got sharper (in case it didn't process it completely yet). So, which resolution and encoding options I should use, if I want the large video player to have the sharpest possible video, retaining the original video quality as good as possible? I noticed that recording with 640x480, the video was sharper than with 1280x720, so I'm not sure what im doing wrong here; both were h264. Is it anyhow possible to prevent YouTube from re-encoding the videos? I just wonder how people can make so sharp videos, while mine are all blurry after upload, but before upload they looked fine. I also tried YouTube's suggested bitrates with h264, but it didn't work any better.

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• Distortion problem with Creative audio equalizer

  - by e-t172

  Hi, I have a problem with the Creative Console EQ, I don't know if it's fixable or not (is the EQ software or hardware on these cards?). Basically, I have enormous distortion with certain sounds in the 30 - 125 hz range. When this happens I get some sort of "frrzzzz" (sorry, I'm french and don't really know the correct english word for that) on top of the original sound. I have a Sound Blaster Audigy SE. I'm using the Daniel_K drivers, on Windows 7 Profesionnal x64. All the effects are disabled except EQ. Steps to reproduce Put the card in 24bit/96khz mode. The problem is also present with 16bit/48khz but seems to be less audible. In the Creative Console, use the following EQ: (full size) Play this sound at a reasonably high volume. You should hear distortion on the two "booms". Especially the second one. Disable Creative EQ. Play the sound in an application with an integrated EQ (e.g. foobar2000, ffdshow) using the same EQ parameters. There is no distortion. Conclusion: the Creative EQ is broken. Is anyone having the same problem? I'm also interested in the results with other Creative cards or even other brands soundcards with a similar EQ feature.

  Read the article

• Cannot find wireless driver for HP laptop

  - by rodey

  I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

  Read the article

• What is the 'best practice' for installing perl modules on Solaris/OpenSolaris?

  - by AndrewR

  I'm currently in the process of writing setup instructions for some software I've written that is implemented as a set of Perl modules. Having done this for various flavours of Linux, I'm now doing the same for Solaris/OpenSolaris (v10 only). Part of the setup process is to make sure that dependent Perl modules are installed. This has been pretty easy on Linux as the Perl modules I require tend to be within the distro's packaging system (eg yum install perl-Cache-Cache). This is not the case on Solaris so I'm working on setup instructions that use the CPAN module to fetch dependent modules (eg perl -MCPAN -e 'install Cache::Cache'). This works ok but there are known problems with modules that require things to be built with a C compiler. The problem is that the C Makefile generated assumes you're using Sun's compiler and uses command-line options not understood by gcc, which you may be using instead. Consulting teh Internetz has thrown up a number of solutions to this: Install and use Sun's compiler Use the perlgcc wrapper script Edit the makefiles by hand (yuk) All of these work. My question to those more familiar with Solaris than me is: Is one of these the 'best' or 'most commonly used' method?

  Read the article

• Very Slow DSL (ethernet) speed

  - by Abhijit

  I 'was' on opensuse 12.2 when my dsl speed was normal. Yesterday I switched from opensuse to ubuntu 12.04 and speed decreased. It came to range of 7-10-13-20-25-kbps. Then I switch to linux mint, and then to fedora. Still slow speed. When I was in ubuntu I disabled ipv6 but still no luck. Now I am in fedora but this time with DIFFERENT ISP. And still I am getting very slow sped. So my guess is this is nothing to do with os. What can be wrong? Is this problem of NIC? Does NIC speed decreases over time? Does NIC life ends over time as with keyboard or mouse? Help please All the os I used are 64 bit and my laptop is Compaq Presario A965Tu Intel Centrino DUal Core. Interesting thing to notice is I get normal speed while downloading torrent inside torrent client softwares. This slow speed issue applied to download from any web browser or installing software using terminal.

  Read the article

• Server 2003 R2 - II6- granting access to website via IP with subnet range

  - by John

  We are trying to allow for a client to connect to our website. By default we are Denying all access except for those with the specified IPs we have configured to run, everything before has just been a single IP address. However now we must implement a range of IPs and rather than input thousands of records we want to use the group of computer options in the Grant Access page. However we have it configured to work off of the IP 72.21.192.0 with a subnet mask of 255.255.224.0 They are unable to connect. Looking over our IIS logs they are receiving a 302 error which is the same behavior anyone should get whom is unauthorized to view the page in question. The IP address coming in is 72.21.217.2, so it should be well within the rage of acceptable IP addresses. I'm at a loss as everything I look up tells me to do what we are doing. So any insight would be appreciated. Especially because I'm a software guy not hardware. Thanks!

  Read the article

• Execute remote shell commands on windows XP embedded

  - by BartD

  The following situation: We have Windows XP Embedded clients that have all admin shares disabled and only have read-only shares (for security reasons). What we want to do is run remote shell (dos) commands on these machines. At first we looked at PsExec & BeyondExec applications (and all sorts of variants), but all of them rely on having at least an admin$ share, which are disabled on our systems. Telnet is not secure enough, as is RSHD servers. So we looked at the next obvious solution: and SSH server. We also prefer an open-source or freeware solution that is still maintained. I looked at freeSSH server for Windows, but that didn't run stable, I tried installing copSSH, WinSSH & openSSH for Windows, but none of these applications seem to work on Windows XP Embedded. The services can either not be installed or cannot be started. I don't know why. Some kind of dependency that is missing. So are there any other solutions out there? I don't care about having to an agent installation locally of some kind on each system, as long as the size of the software is small enough. Can someone suggest some alternatives to what I've already mentioned? Thank you very much.

  Read the article

• Need Help getting perl module DBD::mysql installed for bugzilla on RedHat.

  - by Alos Diallo

  Hi everyone I am having some issues getting Bugzilla setup, I have the software on the server and am trying to get the pre-rec's setup. I am using RedHat 4.1.2-42. I have all of the required perl modules save one:DBD::mysql When I try: sudo perl install-module.pl DBD::mysql I get the following response(this is only an excerpt): rm -f blib/arch/auto/DBD/mysql/mysql.so LD_RUN_PATH="/usr/lib64/mysql:/usr/lib64:/lib64" /usr/bin/perl myld gcc -shared -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic dbdimp.o mysql.o -o blib/arch/auto/DBD/mysql/mysql.so \ -L/usr/lib64/mysql -lmysqlclient -lz -lcrypt -lnsl -lm -L/usr/lib64 -lssl -lcrypto \ /usr/bin/ld: skipping incompatible /usr/lib/libssl.so when searching for -lssl /usr/bin/ld: skipping incompatible /usr/lib/libssl.a when searching for -lssl /usr/bin/ld: cannot find -lssl collect2: ld returned 1 exit status make: * [blib/arch/auto/DBD/mysql/mysql.so] Error 1 /usr/bin/make -- NOT OK Running make test Can't test without successful make Running make install make had returned bad status, install seems impossible I then tried the following: CFLAGS="-I/usr/lib64/mysql:/usr/lib64:/lib64" perl install-module.pl DBD::mysql I get the same result. I have also tried to install it using CPAN but also get the same result. Right now I have DBD-mysql v3.0007 but need (v4.00) Also when I try to install open ssl it says I have the latest version. Does anyone know what I have to do to get this to work? Any help would be greatly appreciated. Thank you

  Read the article

• Windows 7 DVD doesn't boot up, neither does USB. :'(

  - by Manan Shah

  My problem is that i'm not able to install windows 7. Been trying to install this since past 1 week. The methods i've tried are: I have a windows 7 bootable DVD which doesnt boot up. (I've set BIOS to boot from DVD ROM first but it just won't boot from the DVD). Tried to install Windows 7 from the same DVD to a friend's PC and it worked. So the DVD has no issues. I tried to run 'Setup.exe' from within the DVD. The two options pop-up 'Check compatibility' and 'Install now'. On clicking install now, after sometime, an error is encountered with the message 'Windows was unable to create a required installation folder' error code:0x8007000D. I am running Windows XP Professional and there's only one user on the PC which is the Admin, so i do not know why is the setup not getting permissions. I've also uninstalled my antivirus, CD burning software, disabled firewall and disconnected all other devices, but its still the same. I tried to install it from a USB device by making it bootable but that too doesnt work. (Yes the mobo supports booting from the USB). The problem is that XP does not recognize a 'USB' device on boot. Rather it shows this USB stick as a removable 'Hard Drive'. Furthermore, i changed the order of Hard Drive boot to boot from this removable Hard Drive first, it still boots my existing OS. Is there anything else that can be done? Any help would be greatly appreciated. :) Please ask if any other information is required, this post is becomimg increasingly long to add any other details. PS: I want to dual boot windows 7 with my existing XP, but that would be after i manage to run the windows 7 setup in the first place. PPS: Please bare with any 'not-so-technical' terms, i am a beginner with this. Again, thank you for taking the time and trying to help, really appreciate it. :)

  Read the article

• How do I enable additional debugging output from Ansible and Vagrant?

  - by Brian Lyttle

  I'm investigating Ansible for server and application provisioning. My application is currently provisioned with shell scripts in Vagrant. Rather than rewrite my scripts I've taken a sample and attempted to deploy it. It appears to deploy fine, but I've seeing a failure message after what looks like a series of successful steps: » vagrant provision ~/vm/blvagrant 1 ? [default] Running provisioner: ansible... PLAY [web-servers] ************************************************************ GATHERING FACTS *************************************************************** ok: [192.168.9.149] TASK: [install python-software-properties] ************************************ ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [add nginx ppa if it ubuntu 10.04 and up] ******************************* ok: [192.168.9.149] => {"changed": false, "item": "", "repo": "ppa:nginx/stable", "state": "present"} TASK: [update apt repo] ******************************************************* ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [install nginx] ********************************************************* ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [copy fixed init for nginx] ********************************************* ok: [192.168.9.149] => {"changed": false, "gid": 0, "group": "root", "item": "", "mode": "0755", "owner": "root", "path": "/etc/init.d/nginx", "size": 2321, "state": "file", "uid": 0} TASK: [service nginx] ********************************************************* ok: [192.168.9.149] => {"changed": false, "item": "", "name": "nginx", "state": "started"} TASK: [write nginx.conf] ****************************************************** ok: [192.168.9.149] => {"changed": false, "gid": 0, "group": "root", "item": "", "mode": "0644", "owner": "root", "path": "/etc/nginx/nginx.conf", "size": 1067, "state": "file", "uid": 0} PLAY RECAP ******************************************************************** 192.168.9.149 : ok=8 changed=0 unreachable=0 failed=0 Ansible failed to complete successfully. Any error output should be visible above. Please fix these errors and try again. How do I go about getting additional debug information? I've already added ansible.verbose = true to my vagrant config which results in the dictionaries being displayed within the output above.

  Read the article

• How do I set up an email server that automatically maintains a list of previous recipients?

  - by hsivonen

  I want to set up an email server with the following characteristics. What software (besides bogofilter and clamav that I'm naming) should I use and what HOWTOs should I read? The server should run some flavor of Linux that's as low-maintenance as possible and self-updates for security patches in a timely fashion. (Debian stable?) When email is sent, all the recipients are stored in the list of previous recipients maintained by the server. Scan incoming messages with clamav and treat as spam if it contains viruses. When email arrives (if it passed clamav), if the sender is on the list of previous recipients, bypass spam filter. If the List-Id header names a mailing list on a manually maintained list of known-clean mailing lists, bypass spam filter and deliver into a mailbox depending on the mailing list name. Email that wasn't from previous recipients, manually white listed domains or mailing lists gets filtered by bogofilter. Spam goes into a spam mailbox. Email considered to be ham should automatically be fed to bogofilter training as ham. Email considered to be spam (incl. messages with viruses) should be automatically fed to bogofilter training as spam. There should be mailboxes for false ham and false spam that an IMAP client can move email into so that the server retrains bogofilter appropriately. Email sending requires SMTP over SSL. Email reading requires IMAPS. Should I also want to use SpamAssassin in addition to bogofilter?

  Read the article

< Previous Page | 705 706 707 708 709 710 711 712 713 714 715 716  | Next Page >