Search Results

Search found 19200 results on 768 pages for 'xp mode'.

Page 710/768 | < Previous Page | 706 707 708 709 710 711 712 713 714 715 716 717  | Next Page >

• Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

  - by Shoshomiga

  I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

  Read the article

• In search of a good audio player for Ubuntu 9.10

  - by Joe Casadonte

  If this should be marked Community Wiki, please let me know. I'm switching from XP to Ubuntu, and I have been very disappointed with the selection of media players available. I'm primarily interested in an audio player, but integrated video and library management is OK, too. My criteria: Must be able to play audio CDs (I'm shocked how many apps this does away with, right away) Must be able to play MP3 & WAV; OGG, SHN, FLAC are all bonuses Repeat and Shuffle modes are a must FreeDB / GraceNote through a proxy is a must (if it can read a PAC file, that would be awesome) It needs to be really small, e.g. skinnable or an applet Ability to execute a playlist is a plus Gapless MP3 playback a plus I'm running Gnome, but I'm not totally adverse to a KDE app. Command-line only is also a viable option. Some that I've tried: RhythmBox - probably the best of the lot that I've tried; I don't like its mini mode (doesn't show the song being played) and I can't figure out how to get it to hit FreeDB/GraceNote through a proxy Songbird - can't play CDs, playlist management is atrocious Banshee Jajuk Maybe a couple of more. Thanks! UPDATE I tried out VLC, Amarok and Songbord (again). VLC I eventually got to work (I had some kind of bad configuration). It seemed way more involved than I was looking for out of a music player, and in general more geared to video than audio. I couldn't fathom its library management, which I think it has; maybe it doesn't, and that's why I couldn't figure it out. Amaork looked very promising but the library management was not to my liking, and the way it handled a playlist with both MP3 and WAV is inexplicable at best. I did like some aspects of the UI, but not enough to keep it. Songbird is very finicky, but I like the library management. Sort of. It kept telling me my Watch folder was invalid, even thought it clearly was accessible. Playlist management is bizarre, and the message that it was deleting source files whenever I deleted a playlist had me too worried to keep using it. Had it been able to play CDs, maybe I would have persevered. Audacious, while a bit odd at times, does seem to do what I want. If it had a library manager, I wouldn't have bothered trying any of the others. Thanks for the help, everyone!

  Read the article

• file corruption on read/write 2.6.32-22-server (happens across many kernels)

  - by Jonathan

  Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

  Read the article

• Thinkpad speaker turns mute - Linux Codec issue?

  - by Curlew

  At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

  Read the article

• Firefox can't establish a connection to the server at www.google.com

  - by Tom

  My home page in Firefox [v4.0] and Internet Explorer [v9.0.8112.16421, Update Versions RTM (KB982861)] is currently set to Google but when I depress the quick start icon to start up either browser, I am getting the following immediate results: Unable to connect (In Firefox) Firefox can't establish a connection to the server at www.google.com. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Internet Explorer cannot display the webpage What you can try: Diagnose Connection Problems More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. There might be a typing error in the address. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For offline users You can still view subscribed feeds and some recently viewed webpages. To view subscribed feeds: Click the Favorites button , click Feeds, and then click the feed you want to view. To view recently visited webpages (might not work on all pages): Press Alt, click File, and then click Work Offline. Click the Favorites button, click History, and then click the page you want to view. Thankfully, I am able to use one browser that I have installed on my computer (Mathon v3.0.20.5000) to search online for technical assistance in this matter. I have seen several WinSock error issues mentioned; but, they are pointing to Windows XP and I am using Windows 7 Pro and remain uncertain whether anything identified as a fix for one OS will work in another. Things I've tried: HiJackThis Complete scan with Avira AntiVirus Premium. What am I overlooking? What should I do to address this problem?

  Read the article

• How to circumvent ISP Limiting "Unknown" traffic - (SSH)Proxy, VPN

  - by connery

  I am having issues with using a proxy/VPN, with my current ISP (Comenersol, Spain). From my point of view they limit traffic by protocol or by traffic they "know" and "dont know". I'll explain my findings so far below. Internet connection in Spain: ~400-420KByte/sec (speedtest.net) OpenVPN Server in Sweden(pfsense): 100/100Mbit. LZO Compression. TCP. Tun. Aes128 Squid Proxy server in Sweden (pfsense): 100/100 (same box as the vpn server). Plain, no encryption. Runs in stealth mode to hide the use of proxy. NOT running OpenVPN or Squid Proxy, this is my findings: When I download a file from my pfsense box in Sweden, I get maximum speed When I run speedtest.net and choose any european server (including Swedish), I get max speed When I download a torrent (with non default port above 10K), I get limited to ~100KByte/sec. Encryption is turned off If I download something through https, I get max speed Running either Squid Proxy or VPN, this is my findings When I download a file from my pfsense box in Sweden, I get ~100KByte/sec When I run speedtest.net and choose any european server (including Swedish and Spanish), I get ~100Kbyte/sec When I download a torrent, I get same limitation ~100KByte/sec When I download something through https, I get ~100KByte/sec I verify the speeds above with speedtest.net measure, firefox measure in addition to having bmon running in terminal in the background. This way I am certain that the speeds I get presented, are in fact correct. If I connect through a different ISP with VPN or Squid Proxy, I get better speeds (400KByte/sec ++) In short: Whenever I tunnel my traffic through Sweden, my SPanish ISP throttles the traffic. I thought tunneling it through Squid would solve the issue, since I then would no longer hide my traffic through encryption. This does not seem to be the case. Wget and fetch gives same result. I did not try 'nc', but I assume this would give the same result. Does anyone know how to circumvent this issue? I would very much like to be able to get full speed with Swedish ip, as this would make me able to stream TV at higher quality than today. 100KByte/sec just does not cut it quality wise. Thanks for reading. Looking forward for your help.

  Read the article

• nginx + Jetty - thousands of connections stuck in LAST_ACK

  - by virulence

  I have a FreeBSD machine with jails -- two in particular, one that runs nginx and another that runs a Java program that accepts requests via Jetty (embedded mode) Jetty receives upwards of 500 requests/sec constantly and there has been an issue lately where I will constantly have over 60,000 connections in the LAST_ACK state between nginx and jetty. Distribution of all connections (includes some other services, particularly php-fpm) root@host:/root # netstat -an > conns.txt root@host:/root # cat conns.txt | awk '{print $6}' | sort | uniq -c | sort -n 18 LISTEN 112 CLOSING 485 ESTABLISHED 650 FIN_WAIT_2 1425 FIN_WAIT_1 3301 TIME_WAIT 64215 LAST_ACK Distribution of nginx - jetty connections root@host:/root # cat conns.txt | grep '10.10.1.57' | awk '{print $6}' | sort | uniq -c | sort -n 1 3 CLOSE_WAIT 3 LISTEN 18 FIN_WAIT_2 125 ESTABLISHED 64193 LAST_ACK I'd prefer every request to fully close the connection. Clients requests are about 10 minutes apart from each other so connections must be closed. Some of the connections, tcp4 0 0 10.10.1.50.46809 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46805 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46797 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46794 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46790 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46789 10.10.1.57.9050 LAST_ACK tcp4 0 0 10.10.1.50.46771 10.10.1.57.9050 LAST_ACK etc.. On Jetty's end I've set maxIdleTime to 2000 -- before this all connections were in ESTABLISHED but they are now LAST_ACK On Jetty's end I've set Connection: close (i.e response.setHeader(HttpHeaders.CONNECTION, HttpHeaderValues.CLOSE);) Jetty never reports a lot of open connections -- always very few. PF/IPFW is not currently being used nginx - reset_timedout_connection is on I cannot figure out how to get nginx or jetty to forcibly close the connection, is this simply something that needs to be fixed in Jetty so that it fully closes the socket after the request finishes? Thanks a lot in advance EDIT: forgot my nginx config for the proxy setup- proxy_pass http://10.10.1.57:9050; proxy_set_header HTTP_X_GEOIP $http_x_geoip; proxy_set_header GEOIP_COUNTRY_CODE $geoip_country_code; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header Connection ""; proxy_http_version 1.1; EDIT2: Forcing Jetty to close the connection via request.getConnection().getEndPoint().close() does nothing -- it's obvious the connection IS being closed (as it's in LAST_ACK) but why isn't it getting past this? Is Nginx keeping the connection open to the backend for some reason?

  Read the article

• Windows 2003 Storage Server Hanging on Large File Transfers

  - by user25272

  In one of our offices we have a Dell PowerVault 745N NAS device which acts as the main file server. Its running 32bit Windows 2003 Storage Server SP2 with 3GB RAM. The server holds around 60 users HOME folders, which are mapped via AD. The office clients are a mix of XP SP3, Vista and Windows 7. Occasionally the server will completely hang when transferring large files. When the hang happens the console becomes unresponsive with only the mouse active and blank wallpaper. Sometimes stopping the copy frees the server, sometimes not. The hanging can last around 20 minutes. During this time other servers also become unresponsive with blank wallpaper at the console. If you do manage to get onto another server the taskbar and run commands are unresponsive. This also transcends to the client computers sometimes with explorer crashing. I'm guessing this is due to the HOME folder mapping. Eventually the NAS server with free up and everything will be back to normal. The server is configured as follows: PERC 4/DC DATA 2 - 12 SCSI HDD - RAID5 SHADOWCOPY 2 SCSI HDD - RAID1 CERC SATA DATA 11 4 SATA HDD - RAID5 OS 4 SATA HDD - RAID5 All the drivers and firmware is up to date. I've been through all the diagnostics with Dell and the hardware has come up clean including full HDD tests on the arrays. The server has NOD32 installed as the AV, but the hanging happens when it is uninstalled. There are no errors in the event log when this happens and we don't have any errors logged on any of our ProCurve switches. DNS is fine on the domain and AD from what I can tell is running happily. There are no DFS or NFS shares setup either. All the shares are standard Windows. I've unchecked the allow the computer to turn off this device to save power box under Power Management on the NIC. "Set Link Speed and Duplex to Auto-negotiate 1000 " Increased Receive Descriptors buffer from 256 to 352 (reserves more CPU resource for handling data) I've run network traces using network monitor and have found the following: 417 8.078125 {SMB:192, NbtSS:25, TCP:24, IPv4:23} 192.168.2.244 192.168.5.35 SMB SMB:R; Nt Create Andx - NT Status: System - Error, Code = (52) STATUS_OBJECT_NAME_NOT_FOUND I've tried different cabling; NICs and switch ports all with the same result. Transferring files from other servers on the domain is fine. All I haven't done is run CHKDSK on the drives to look for any file system errors. On the Vista clients I have also run netsh interface tcp set global autotuning=disabled with no result. Could it be that the server has a faulty drive or that the I/O is too much for it to handle? Any ideas why would the hang cause issues with the other servers on the LAN? Many Thanks.

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• Graphics card artifacting

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 @ stock clocks 3x 2GB DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) My graphics card started artifacting while I was playing a game. It artifacted, the display blinked, then I got an NVIDIA driver has crashed and recovered message. Kept going, more artifacts, another crash, but this time my display blanked out and I couldn't do anything. Restarted my computer - artifacting is in the BIOS - got to Windows 7 but it BSOD'd before I could even log in. I restarted the computer again - artifacts cleared themselves out and I managed to get to Win7, but it soon started blinking in and out and artifacting again. Checked the card temps and they're well within range. (50 idle, 70 full load) The ambient temperature here is about 80-85F with high humidity. Tried Safe Mode and it still froze up/BSOD'd. Already tried the following to fix this problem: - Reseat the graphics card and swapped in a different slot. - Removed cover on card and sprayed with compressed air to clean it out. - Swapped around memory and/or went with only using one stick at a time. - Underclocked card I called EVGA Tech Support and they said that the voltage on the 12V rail of my Corsair AX750 PSU was on the high end of the "acceptable" range (12.4V, highest within acceptable range is 12.6V - optimal is obviously 12V). They gave me an RMA number anyway, but I want to get a second opinion from you all before I send this thing off, as shipping from where I live to EVGA is kind of pricey. This PSU is only 6 months old. So that I don't have to play RMA tag, which case would be most likely? I'm strapped for cash at the moment so I want to reduce the amount of RMAs I have to do since shipping is expensive here. Is there any surefire way to test to see if it's really the graphics card or the PSU? I tried unplugging any devices that were connected to the 12V rail (except for my SSD and graphics card) as I do have 3 mechanical hard drives, but the voltage for that rail didn't drop (it remained at 12.4V). I'm fairly sure it isn't the drivers since I'm getting the artifacting at the BIOS too. Right now I'm back in Windows 7 but I don't know for how long until it messes up again. Any ideas?

  Read the article

• Puppet and launchd services?

  - by Joel Westberg

  We have a production environment configured with Puppet, and want to be able to set up a similar environment on our development machines: a mix of Red Hats, Ubuntus and OSX. As might be expected, OSX is the odd man out here, and sadly, I'm having a lot of trouble with getting this to work. My first attempt was using macports, using the following declaration: package { 'rabbitmq-server': ensure => installed, provider => macports, } but this, sadly, generates the following error: Error: /Stage[main]/Rabbitmq/Package[rabbitmq-server]: Could not evaluate: Execution of '/opt/local/bin/port -q installed rabbitmq-server' returned 1: usage: cut -b list [-n] [file ...] cut -c list [file ...] cut -f list [-s] [-d delim] [file ...] while executing "exec dscl -q . -read /Users/$env(SUDO_USER) NFSHomeDirectory | cut -d ' ' -f 2" (procedure "mportinit" line 95) invoked from within "mportinit ui_options global_options global_variations" Next up, I figured I'd give homebrew a try. There is no package provider available by default, but puppet-homebrew seemed promising. Here, I got much farther, and actually managed to get the install to work. package { 'rabbitmq': ensure => installed, provider => brew, } file { "plist": path => "/Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist", source => "/usr/local/opt/rabbitmq/homebrew.mxcl.rabbitmq.plist", ensure => present, owner => root, group => wheel, mode => 0644, } service { "homebrew.mxcl.rabbitmq": enable => true, ensure => running, provider => "launchd", require => [ File["/Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist"] ], } Here, I don't get any error. But RabbitMQ doesn't start either (as it does if I do a manual load with launchctl) [... snip ...] Debug: Executing '/bin/launchctl list' Debug: Executing '/usr/bin/plutil -convert xml1 -o /dev/stdout /Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist' Debug: Executing '/usr/bin/plutil -convert xml1 -o /dev/stdout /var/db/launchd.db/com.apple.launchd/overrides.plist' Debug: /Schedule[weekly]: Skipping device resources because running on a host Debug: /Schedule[puppet]: Skipping device resources because running on a host Debug: Finishing transaction 2248294820 Debug: Storing state Debug: Stored state in 0.01 seconds Finished catalog run in 25.90 seconds What am I doing wrong?

  Read the article

• Why do I sometimes get 'sh: $'\302\211 ... ': command not found' in xterm/sh?

  - by amn

  Sometimes when I simply type a valid command like 'find ...', or anything really, I get back the following, which is completely unexpected and confusing (... is command name I type): sh: $'\302\211...': command not found There is some corruption going on I think. I don't use color in my prompt, I am using the Bash shell in POSIX mode as sh (chsh to /bin/sh and so on - $SHELL is sh). What is going on and why does this keep happening? Anything I can debug? I think this is more of an xterm issue than sh, or at least a combination of the two. Files, for context: My /etc/profile, as distributed with Arch Linux x86-64: # /etc/profile #Set our umask umask 022 # Set our default path PATH="/usr/local/sbin:/usr/local/bin:/usr/bin" export PATH # Load profiles from /etc/profile.d if test -d /etc/profile.d/; then for profile in /etc/profile.d/*.sh; do test -r "$profile" && . "$profile" done unset profile fi # Source global bash config if test "$PS1" && test "$BASH" && test -r /etc/bash.bashrc; then . /etc/bash.bashrc fi # Termcap is outdated, old, and crusty, kill it. unset TERMCAP # Man is much better than us at figuring this out unset MANPATH My /etc/shrc, which I created as a way to have sh parse some file on startup, when non-login shell. This is achieved using ENV variable set in /etc/environment with the line ENV=/etc/shrc: PS1='\u@\H \w \$ ' alias ls='ls -F --color' alias grep='grep -i --color' [ -f ~/.shrc ] && . ~/.shrc My ~/.profile, I am launching X when logging in through first virtual tty: [[ -z $DISPLAY && $XDG_VTNR -eq 1 ]] && exec xinit -- -dpi 111 My ~/.xinitc, as you can see I am using the system as a Virtual Box guest: xrdb -merge ~/.Xresources VBoxClient-all awesome & exec xterm And finally, my ~/.Xresources, no fancy stuff here I guess: *faceName: Inconsolata *faceSize: 10 xterm*VT100*translations: #override <Btn1Up>: select-end(PRIMARY, CLIPBOARD, CUT_BUFFER0) xterm*colorBDMode: true xterm*colorBD: #ff8000 xterm*cursorColor: S_red Since ~/.profile references among other things /etc/bash.bashrc, here is its content: # # /etc/bash.bashrc # # If not running interactively, don't do anything [[ $- != *i* ]] && return PS1='[\u@\h \W]\$ ' PS2='> ' PS3='> ' PS4='+ ' case ${TERM} in xterm*|rxvt*|Eterm|aterm|kterm|gnome*) PROMPT_COMMAND=${PROMPT_COMMAND:+$PROMPT_COMMAND; }'printf "\033]0;%s@%s:%s\007" "${USER}" "${HOSTNAME%%.*}" "${PWD/#$HOME/~}"' ;; screen) PROMPT_COMMAND=${PROMPT_COMMAND:+$PROMPT_COMMAND; }'printf "\033_%s@%s:%s\033\\" "${USER}" "${HOSTNAME%%.*}" "${PWD/#$HOME/~}"' ;; esac [ -r /usr/share/bash-completion/bash_completion ] && . /usr/share/bash-completion/bash_completion I have no idea what that case statement does, by the way, it does look a bit suspicious though, but then again, who am I to know.

  Read the article

• seaudit report detail

  - by user1014130

  I've just started using selinux in the last 6 months and am getting to grips with it. However, using sealert on a new CENTOS 6 server, Im not getting the level of detail I was with CENTOS 5. To illustrate: Running sealert -a /var/log/audit/audit.log On CENTOS 5 I get: Summary: SELinux is preventing postdrop (postfix_postdrop_t) "getattr" to /var/log/httpd/error_log (httpd_log_t). Detailed Description: SELinux denied access requested by postdrop. It is not expected that this access is required by postdrop and this access may signal an intrusion attempt. It is also possible that the specific version or configuration of the application is causing it to require additional access. Allowing Access: Sometimes labeling problems can cause SELinux denials. You could try to restore the default system file context for /var/log/httpd/error_log, restorecon -v '/var/log/httpd/error_log' If this does not work, there is currently no automatic way to allow this access. Instead, you can generate a local policy module to allow this access - see FAQ (http://fedora.redhat.com/docs/selinux-faq-fc5/#id2961385) Or you can disable SELinux protection altogether. Disabling SELinux protection is not recommended. Please file a bug report (http://bugzilla.redhat.com/bugzilla/enter_bug.cgi) against this package. Additional Information: Source Context root:system_r:postfix_postdrop_t Target Context system_u:object_r:httpd_log_t Target Objects /var/log/httpd/error_log [ file ] Source postdrop Source Path /usr/sbin/postdrop Port Host Source RPM Packages postfix-2.3.3-2.1.el5_2 Target RPM Packages Policy RPM selinux-policy-2.4.6-279.el5_5.1 Selinux Enabled True Policy Type targeted MLS Enabled True Enforcing Mode Enforcing Plugin Name catchall_file Host Name server109-228-26-144.live-servers.net Platform Linux server109-228-26-144.live-servers.net 2.6.18-194.8.1.el5 #1 SMP Thu Jul 1 19:04:48 EDT 2010 x86_64 x86_64 Alert Count 1 First Seen Wed Jun 13 11:43:55 2012 Last Seen Wed Jun 13 11:43:55 2012 but on CENTOS 6 I just get: Summary: SELinux is preventing postdrop (postfix_postdrop_t) "getattr" to /var/log/httpd/error_log (httpd_log_t). Detailed Description: SELinux denied access requested by postdrop. It is not expected that this access is required by postdrop and this access may signal an intrusion attempt. It is also possible that the specific version or configuration of the application is causing it to require additional access. Allowing Access: Sometimes labeling problems can cause SELinux denials. You could try to restore the default system file context for /var/log/httpd/error_log, restorecon -v '/var/log/httpd/error_log' If this does not work, there is currently no automatic way to allow this access. Instead, you can generate a local policy module to allow this access - see FAQ (http://fedora.redhat.com/docs/selinux-faq-fc5/#id2961385) Or you can disable SELinux protection altogether. Disabling SELinux protection is not recommended. Please file a bug report (http://bugzilla.redhat.com/bugzilla/enter_bug.cgi) against this package. Im running exactly the same command. Does anyone have any idea why Im not getting the "Additional information" that I do with CENTOS 5? Thanks in advance Dylan

  Read the article

• Network switching issues with MacOS 10.7?

  - by Denis

  I'm having a wired problem and hope somebody can tip me, what way should I dig to. I'm using MacBookPro with Lion 10.7.3 both at my working place & at home. At working place, we have a domain-based network with 802.1x authorization (more than 400 computers) and to connect it I'm using Ethernet cable. IP range is 10.10.2.*. All network settings are setup automatically by DHCP. Also, in settings, I have Network Account Server setup in the User&Groups Settings for my work Domain server - and it is available only from corporate network. At home, I have an ADSL router, that shares Internet connection by WiFi in NAT mode. I'm using WiFi to connect it. Router gives out addresses from 192.168.1.* range and all settings are also set up by router's DHCP. So, my problem is the following. When I come back home from the office, I open my MacBook and AirPort automatically connects my WiFi network. After this, for about 1 minute I'm able to browse sites & ping hosts successfully. But after this minute, network connection is broken down. All pings return time-out. trace route to google.com stops on 192.168.1.1 (which is my router). This lasts for 3-4 minutes. After that network connection is automatically repaired and all pings go smoothly again. At the same time, when my MacBook return timeouts, I can successfully ping any host from my wife's MacBook - so this doesn't look like router issue. When I come to the office, I don't have any issues and Internet connection is available & stable moments after ethernet cable plugged in. Do anybody has any clues about this? What should I monitor & what settings look for resolving this issue? Please, ask, what additional information should I provide. Hoping for good advice & thanks in advance!

  Read the article

• Searching For a Desktop Security Software to harden Windows machines, anybody?

  - by MosheH

  I'm a network administrator of a small/medium network. I'm looking for a software (Free or Not) which can harden Windows Computers (XP And Win7) for the propose of hardening standalone desktop computers (not in domain network). Note: The computers are completely isolated (standalone), so i can't use active directory group policy. moreover, there are too many restriction that i need to apply, so it is not particle to set it up manual (one by one). Basically what I’m looking for is a software that can restrict and disable access for specific user accounts on the system. For Example: User john can only open one application and nothing else -- He don’t see no icon on the desktop or start menu, except for one or two applications which i want to allow. He can't Right click on the desktop, the task-bar icons are not shown, there is no folder options, etc... User marry can open a specific application and copy data to one folder on D drive. User Dan, have access to all drives but cannot install software, and so on... So far ,I've found only the following solutions, but they all seems to miss one or more feature: Desktop restriction Software 1. Faronics WINSelect The application seems to answer most of our needs except one feature which is very important to us but seems to be missing from WINSelect, which is "restriction per profile". WINSelect only allow to set up restrictions which are applied system-wide. If I have multiple user accounts on the system and want to apply different restrictions for each user, I cant. Deskman (No Restriction per user)- Same thing, no restriction per profile. Desktop Security Rx - not relevant, No Win7 Support. The only software that I've found which is offering a restriction per profile is " 1st Security Agent ". but its GUI is very complicated and not very intuitive. It's worth to mention that I'm not looking for "Internet Kiosk software" although they share some features with the one I need. All I need is a software (like http://www.faronics.com/standard/winselect/) that is offering a way to restrict Windows user interface. So if anybody know an Hardening software which allows to set-up user restrictions on Windows systems, It will be a big, big, big help for me! Thanks to you all

  Read the article

• NFS4 / ZFS: revert ACL to clean/inherited state

  - by Keiichi

  My problem is identical to this Windows question, but pertains NFS4 (Linux) and the underlying ZFS (OpenIndiana) we are using. We have this ZFS shared via NFS4 and CIFS for Linux and Windows users respectively. It would be nice for both user groups to benefit from ACLs, but the one missing puzzle piece goes thusly: Each user has a home, where he sets a top-level, inherited ACL. He can later on refine permissions for the contained files/folders iteratively. Over time, sometimes permissions need to be generalized again to avoid increasing pollution of ACL entries. You can tweak the ACL of every single file if need be to obtain the wanted permissions, but that defeats the purpose of inherited ACLs. So, how can an ACL be completely cleared like in the question linked above? I have found nothing about what a blank, inherited ACL should look like. This usecase simply does not seem to exist. In fact, the solaris chmod manpage clearly states A- Removes all ACEs for current ACL on file and replaces current ACL with new ACL that represents only the current mode of the file. I.e. we get three new ACL entries filled with stuff representing the permission bits, which is rather useless for cleaning up. If I try to manually remove every ACE, on the last one I get chmod A0- <file> chmod: ERROR: Can't remove all ACL entries from a file Which by the way makes me think: and why not? In fact, I really want the whole file-specific ACL gone. The same holds for linux, which enumerates ACEs starting with 1(!), and verbalizes its woes less diligently nfs4_setacl -x 1 <file> Failed setxattr operation: Unknown error 524 So, what is the idea behind ACLs under Solaris/NFS? Can they never be cleaned up? Why does the recursion option for the ACL setting commands pollute all children instead of setting a single ACL and making the children inherit? Is this really the intention of the designers? I can clean up the ACLs using a windows client perfectly well, but am I supposed to tell the linux users they have to switch OS just to consolidate permissions?

  Read the article

• Moving default web site to another drive

  - by Chadworthington

  I set the default location from c:\inetpub\wwwroot to d:\inetpub\wwwroot but when I access my .NET 4.0 site get this error: Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 105: Set explicit="true" to force declaration of all variables. Line 106: --> Line 107: <compilation debug="true" strict="true" explicit="true" targetFramework="4.0"> Line 108: <assemblies> Line 109: <add assembly="System.Web.Extensions.Design, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"/> When I try to Manage the Basic Settings on the Site and click the "Test Settings" button, I see that I have a problem under "authorization:" The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that <domain>\<computer_name>$ has Read access to the physical path. Then test these settings again. 1) Do I need to grant rights to IIS to the new folder? Which user? I thought it was something like IIS_USER or something similar but I cannot determine the correct name of the user. 2) Also, do I need to set the default version of the framework somewhere at the Default Site level or at the Virtual folder level? How is this done in IIS6, I am used to IIS5 or whatever came with XP Pro. 3) My original site had a subfolder under wwwroot called "aspnet_client." How was this cleated? I manually copied it to the corresponding new location. My app was using seperate ASP specific databases for storing session state and role info, if that is relevant. Thanks

  Read the article

• Virtualbox - routing subnet to bridge adapters

  - by user42384

  Hello, I have set up a Debian Lenny box with 3 vbox Lenny machines running eth0 of the host in bridged mode (on virtualbox 3.1.6). When testing in my local LAN, this all worked perfectly well and traffic flowed to and from the IPs of the virtual machines as it should. However, now that it's in its co-lo home, the networking setup is a bit different, and I'm unable to get traffic to flow to the vboxes properly. Specifically, the host has its own Primary IP, and I have a separate subnet of 8 (6 usable) IPs routed to the box for use by the vboxes. So, eth0 on host is: Machine IP: 2x.x.x.137 Gateway IP: 2x.x.x.138 Subnet Msk: 255.255.255.252 Subnet for vboxes is Subnet: 2x.x.x.240/29 Netmask: 255.255.255.248 vbox1 is configured to 2x.x.x.241 on eth0 as follows: auto eth0 iface eth0 inet static address 2x.x.x.241 netmask 255.255.255.248 Setting up a virtual interface (eth0:0) on the host with one of these subnet IPs allows me to ping to that address only from vbox1, and it allows me to ping vbox1 from the host. I can also ping that virtual interface perfectly well from outside, so the IPs are definitely landing at my machine. It seems I'm missing some sort of routing instruction either on the host or vbox1 to get traffic moving between the subnet and the default gateway, but I can't seem to figure out what it should be, or what glaringly obvious thing i'm missing. Most of my obvious attempts (the gw of eth0, the ip of eth0) were rejected by route command with SIOCADDRT: No such device (eg - i can't find it). I tried setting vbox1 to bridge on eth0:0, but this was not an acceptable device name and VBoxHeadless refused to start. The physical machine does have an unused physical NIC at eth1 that can be used if necessary for something or other. Host machine is running iptables configured by ferm, have experimented with it allowing forwarding for that subnet, but I wouldn't have thought this was necessary given the nature of the virtualbox devices (nor did it actually work). Clearing out all of these rules for a blank iptables set does not resolve the issue. (you can see ferm generated iptables at http://codedumper.com/ojaze) Thanks for any help you can give... Patrick

  Read the article

• Port forwarding not working properly

  - by sudo work

  I'm trying to host a small web server from my home network; however, I have not been able to successfully port forward ports to the local server. My current network topology looks like this: Cable Modem/Router - Secondary Wireless Router - Many computers (including server) The modem/router I'm using is a Cisco (Scientific Atlantic) DPC2100, provided by my ISP. The wireless router that I'm using as the central hub to my home network is a Linksys E3000. The computer being used as a server is running Ubuntu 10.04 Server Edition. The main issue is that I can't access the server remotely, using my WAN IP address. I have port forwarded my wireless router; however, I believe that I need to somehow set my modem to bridge mode. As far as I can tell though, this isn't possible. Here are the various IP address settings: DPC2100 WAN: 69.xxx.xxx.xxx Internal IP: 192.168.100.1 Internal Network: 192.168.7.0 E3000 IP Address: 192.168.7.2 Gateway: 192.168.7.1 Internal IP: 192.168.1.1 Internal Network: 192.168.1.0 Server IP Address: 192.168.1.123 Gateway: 192.168.1.1 Now I can do an nmap at various nodes, and here are the results (from the server): nmap localhost: 22,25,53,80,110,139,143,445,631,993,995,3306,5432,8080 open nmap 192.168.7.2: 22,25,80 (filtered),110,139,445 open (ports I have forwarded in the E3000)* nmap 69.xxx.xxx.xxx: 1720 open *For some reason, I can SSH into the server at 192.168.7.2, but not view the website. Here are also some other settings: /etc/hosts/ 127.0.0.1 localhost 127.0.1.1 servername ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/apache2/sites-available/default snippet <VirtualHost *:80> DocumentRoot /srv/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> ... </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> ... </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> ... </Directory> </VirtualHost> Let me know if you need any other information; some stuff probably slipped my mind.

  Read the article

• git private server error: "Permission denied (publickey)."

  - by goddfree

  I followed the instructions here in order to set up a private git server on my Amazon EC2 instance. However, I am having problems when trying to SSH into the git account. Specifically, I get the error "Permission denied (publickey)." Here are the permissions of my files/folders on the EC2 server: drwx------ 4 git git 4096 Aug 13 19:52 /home/git/ drwx------ 2 git git 4096 Aug 13 19:52 /home/git/.ssh -rw------- 1 git git 400 Aug 13 19:51 /home/git/.ssh/authorized_keys Here are the permissions of my files/folders on my own computer: drwx------ 5 CYT staff 170 Aug 13 14:51 .ssh -rw------- 1 CYT staff 1679 Aug 13 13:53 .ssh/id_rsa -rw-r--r-- 1 CYT staff 400 Aug 13 13:53 .ssh/id_rsa.pub -rw-r--r-- 1 CYT staff 1585 Aug 13 13:53 .ssh/known_hosts When checking my logs in /var/log/secure, I used to get the following error message every time I tried to SSH: Authentication refused: bad ownership or modes for file /home/git/.ssh/authorized_keys However, after making a few permission changes, I no longer get this error message. Despite this, I am still getting the "Permission denied (publickey)." message every time I try to SSH. The command I am using to SSH is ssh -T git@my-ip. Here is the full log I get when I run ssh -vT [email protected]: OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to my-ip [my-ip] port 22. debug1: Connection established. debug1: identity file /Users/CYT/.ssh/id_rsa type -1 debug1: identity file /Users/CYT/.ssh/id_rsa-cert type -1 debug1: identity file /Users/CYT/.ssh/id_dsa type -1 debug1: identity file /Users/CYT/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.2 debug1: match: OpenSSH_6.2 pat OpenSSH* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr [email protected] none debug1: kex: client->server aes128-ctr [email protected] none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 08:ad:8a:bc:ab:4d:5f:73:24:b2:78:69:46:1a:a5:5a debug1: Host 'my-ip' is known and matches the RSA host key. debug1: Found key in /Users/CYT/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /Users/CYT/.ssh/id_rsa debug1: Trying private key: /Users/CYT/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). I have spent a few hours going through threads on various sites, including SO and SF, looking for a solution. It seems that the permissions for my files are all okay, but I just can't figure out the problem. Any help would be greatly appreciated. Edit: EEAA: Here are the outputs you requested: $ getent passwd git git:x:503:504::/home/git:/bin/bash $ grep ssh ~git/.ssh/authorized_keys | wc -l grep: /home/git/.ssh/authorized_keys: Permission denied 0

  Read the article

• Can Remote Desktop Services be deployed and administered by PowerShell alone, without a Domain in WIndows Server 2012 and 2012 R2?

  - by Warren P

  Windows Server 2008 R2 allowed deployment of Terminal Server (Remote Desktop Services) without a domain, and without any insistence on domains. This was very useful, especially for standalone virtual or cloud deployments of a server that is managed remotely for a remote client who has no need or desire for any ActiveDirectory or Domain features. This has become steadily more and more difficult as Microsoft restricts its technologies further and further in each Windows release. With Windows Server 2012, configuring licensing for Remote Desktop Services, is more difficult when not on a domain, but possible still. With Windows Server 2012 R2 (at least in the preview) the barriers are now severe: The Add/Remove Roles and Features wizard in Windows Server 2012 R2 has a special RDS deployment mode that has a rule that says if you aren't on a domain you can't deploy. It tells you to create or join a domain first. This of course comes in direct conflict with the fact that an Active Directory domain controller should not be the same machine as a terminal server machine. So Microsoft's technology is not such much a Cloud Operating System as a Cluster of Unwanted Nodes, needed to support the one machine I actually WANT to deploy. This is gross, and so I am trying to find a workaround. However if you skip that wizard and just go check the checkboxes in the main Roles/Features wizard, you can deploy the features, but the UI is not there to configure them, and when you go back to the RDS configuration page on the roles wizard, you get a message saying you can not administer your Remote Desktop Services system when you are logged in as a Local-Computer Administrator, because although you have all admin priveleges you could have (in your workgroup based system), the RDS configuration UI will not accept those credentials and let you continue. My question in brief is, can I still somehow, obtain the following end result: I need to allow 10-20 users per system to have an RDS (TS) session. I do not need any of the fancy pants RDS options, unless Microsoft somehow depends on those features being present. I believe I need the "RDS Session Host" as this is the guts of "Terminal Server". Microsoft says it is "full Windows desktop for Remote Desktop Services client. I need to configure licensing so that the Grace Period does not expire leaving my RDS non functional, so this probably means I need a way to configure TS CALs. If all of the above could technically be done with the judicious use of the PowerShell, I am prepared to even consider developing all the PowerShell scripts I would need to do the above. I'm not asking someone to write that for me. What I'm asking is, does anyone know if there is a technical impediment to what I want to do above, other than the deliberate crippling of the 2012 R2 UI for Workgroup users? Would the underlying technologies all still work if I manipulate and control them from a PowerShell script? Obviously a 1 word Yes or No answer isn't that useful to anyone, so the question is really, yes or no, and why? In the case the answer is Yes, then how.

  Read the article

• Two-Hop SSH connection with two separate public keys

  - by yigit

  We have the following ssh hop setup: localhost -> hub -> server hubuser@hub accepts the public key for localuser@localhost. serveruser@server accepts the public key for hubuser@hub. So we are issuing ssh -t hubuser@hub ssh serveruser@server for connecting to server. The problem with this setup is we can not scp directly to the server. I tried creating .ssh/config file like this: Host server user serveruser port 22 hostname server ProxyCommand ssh -q hubuser@hub 'nc %h %p' But I am not able to connect (yigit is localuser): $ ssh serveruser@server -v OpenSSH_6.1p1, OpenSSL 1.0.1c 10 May 2012 debug1: Reading configuration data /home/yigit/.ssh/config debug1: /home/yigit/.ssh/config line 19: Applying options for server debug1: Reading configuration data /etc/ssh/ssh_config debug1: Executing proxy command: exec ssh -q hubuser@hub 'nc server 22' debug1: permanently_drop_suid: 1000 debug1: identity file /home/yigit/.ssh/id_rsa type 1000 debug1: identity file /home/yigit/.ssh/id_rsa-cert type -1 debug1: identity file /home/yigit/.ssh/id_dsa type -1 debug1: identity file /home/yigit/.ssh/id_dsa-cert type -1 debug1: identity file /home/yigit/.ssh/id_ecdsa type -1 debug1: identity file /home/yigit/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH_5* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: ECDSA cb:ee:1f:78:82:1e:b4:39:c6:67:6f:4d:b4:01:f2:9f debug1: Host 'server' is known and matches the ECDSA host key. debug1: Found key in /home/yigit/.ssh/known_hosts:33 debug1: ssh_ecdsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/yigit/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Trying private key: /home/yigit/.ssh/id_dsa debug1: Trying private key: /home/yigit/.ssh/id_ecdsa debug1: No more authentication methods to try. Permission denied (publickey). Notice that it is trying to use the public key localuser@localhost for authenticating on server and fails since it is not the right one. Is it possible to modify the ProxyCommand so that the key for hubuser@hub is used for authenticating on server?

  Read the article

• How to enjoy DVD on Apple iPad

  - by user44251

  I believe many people spent a sleepless night yesterday waiting for the new Apple Tablet to come, just a few days ago or perhaps longer I noticed fierce debate about it, its name, size, capacity, processor, main features, price etc. And now, they can take a long breath with the new Apple Tablet named iPad officially released on 28, January, 2010 (Beijing Time). But I know a new battle just begins. iPad, sounds somewhat like iPod and it really shares some similarities in terms of shape like smart, light and portable. It has a 9.7-inch, LED-backlit, IPS display with a remarkable precise Multi-Touch screen. And yet, at just 1.5 lbs and 0.5 inches thin, it's easy to carry and use everywhere. It can greatly facilitates your experience with the web, emails, photos and videos. Right now, it can run almost 140.000 of the apps on the Apple store. It can even run the apps you have downloaded for your iPhone or iPod touch. But so far, I haven't seen any possibility that it can work with DVD, probability there is no built-in DVD-ROM or DVD player which can play DVD directly. As Apple iPad states, the video formats supported are MPEG-4 (MP4, M4V), H.264, MOV etc and audio formats accepted are AAC, Proteceted AAC, MP3, AIFF and WAV etc, those are formats that are commonly used with iMac. This could really a hard nut to crack if you want to watch your favourite DVD on this magic Apple iPad. But don't worry, there is still way out, you just need a few steps for ripping and importing DVD movies to Apple iPad with a simple application DVD to iPad converter What's on DVD to iPad Converter for Mac DVD to iPad converter for Mac is a powerful and professional application designed for the newly released Apple iPad which can rip, convert your DVD contents to Apple iPad compatible MPEG-4 (MP4, M4V), H.264, MOV etc, and other popular file formats like AVI, WMV, MPG, MKV, VOB, 3GP, FLV etc can also be converted so that you can put on your portable devices like iPod, iPhone, iRiver, BlackBerry etc. Besides, it can also extract audio from DVD videos and save as MP3, AIFF, AAC, WAV etc. Mac DVD to iPad converter has also been enhanced that can run both on PowerPC and Intel (Snow Leopard included). It can offer versatile editing features which allows you to make your own DVD videos. For example, you can cut your DVD to whatever length you like by Trim, crop off unwanted parts from DVD clips by Crop, add special effect like Gray, Emboss and Old film to make your videos more artistic. Besides, its built-in merging feature and batch mode allows you to join several DVD clips into a single one and do batch conversion. And more features can be expected if you afford a few minutes to try.

  Read the article

• What is the probable failure - no BSOD, no event log, monitors sleeping, force reboot required

  - by Tyler

  Every 3 to 15 days, my PC freezes. This typically happens when the computer is idle, I'm coming home from work, back from vacation, etc. It's never happened while using my computer. The monitors are in power save mode The Caps Lock light on the (wireless) keyboard doesn't work Ctrl-alt-del has no effect, mouse (wireless) has no effect The hardware reset button and single press of power putton have no effect Computer does not appear on the network No BSOD, no memory dump Event logs have no errors or indications of problems near the time of crash. Only messages after reboot indicating that there was a reboot without a clean shutdown. Windows is set to never put the computer to sleep (just the display) Here are the vital stats of the build: OS Windows 8 Pro 64-bit CPU Intel i5-2400 Mobo Intel BOXDP67DE Micro ATX GPU MSI N460GTX Cyclone768D5/OC RAM CORSAIR XMS3 8GB (2 x 4GB) CMX8GX3M2A1333C9 PSU SeaSonic X Series X650 Gold System Drive Samsung 840 Pro 256 GB SSD Data Drive 2 x Western Digital WD20EARS 2TB in hardware RAID 1 Optical Lite-On DVD burner IHAS424-98 And here is the story of how the problem developed and what I've done to diagnose: January 2011, system built with Windows 7 64-bit, runs great. March 2011, Intel replaced the mobo because of the bad sata controllers. October 2012, upgrade to Windows 8 (problems start shortly after). January 2013, system freezes and causes network to fail for the whole house. Unplug the network cable and other devices and PCs can use the internet. Plug it back in, internet goes away for everyone. Reboot and everything is fine. March 2013, install Intel Gigabit CT PCI-E NIC, disable mobo nic in bios. Network strangeness goes away. Freezes are less frequent. Memtest shows no problems (20 passes). Early June 2013, replace Antec PSU with SeaSonic PSU. Mid June 2013, replace OCZ Vertex 2 SSD with Samsung SSD. Late June 2013, get frustrated and hope the community has some good ideas (I'm running out of budget to replace parts). My next plan of attack is setting "Turn off display" to Never and using a screen saver to see how that reacts on the next freeze. It makes me sad to waste power for up to 15 days though. Has anyone out there seen a problem like this? Any ideas on what kind of malfunction would act this way? Ideas of other diagnostic steps to take?

  Read the article

< Previous Page | 706 707 708 709 710 711 712 713 714 715 716 717  | Next Page >