Search Results

Search found 18842 results on 754 pages for 'the machine'.

Page 712/754 | < Previous Page | 708 709 710 711 712 713 714 715 716 717 718 719  | Next Page >

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• VPN Connection Causes Internal LAN Connection Loss with Server

  - by sleepisfortheweak

  I've tried configuring basic PPTP VPN at my small business using a number of different tutorials. As far as I can tell, the actual VPN connection worked fine, but upon connecting a client, the Server 'disappears' from the internal LAN. The RRAS service must be stopped before the connection is restored. My Setup: The network is simply a DSL Gateway/Router to the outside functioning as NAT/Firewall/DHCP. The server is a Win Server 2008 machine at fixed IP 192.168.1.200. The server has 1 NIC, so I used the 'custom' option when configuring RRAS. The RRAS settings should be default except that I've disabled ports for connection types I'm not using and reduced PPTP ports to 10. I've also created an address pool and disabled DHCP packet forwarding. The server only functions as a File Share and now a VPN Server. Local LAN computers all have mapped network shares to the server authenticated based on Local User/Group setup on the server. The Problem: The moment a client connects through VPN, the server 'disappears' from the local network. All mapped drives disconnect and there is no response to a ping 192.168.1.200. Even if the client disconnects, the server does not re-appear at that address until the RRAS service is stopped. I've Tried: Using an Address Pool inside and outside the local subnet. Using DCHP Relay Checking Inbound/Outbound filters (none enabled) The fact that nothing I've tried has had any effect, and that I can connect and successfully obtain an IP tells me that it's something more fundamental I'm missing. My gut tells me that it's something to do with the second IP address added by the VPN client somehow taking over the interface or traffic from the local LAN accidently getting routed to the VPN client instead of handled at the server once RRAS has become 'active' when a client connects. Hopefully this may be obvious to someone with real IT experience. I've been doing this a while and almost never been stumped. I'm starting to think it might actually be something tricky since my setup is pretty basic yet refuses to work. I'll be happy to include more info if this doesn't ring any bells right away for anyone. Thanks

  Read the article

• One user sometimes gets an unknown certificate error opening Outlook

  - by Chris

  Let me clarify a little. This isn't an unknown certificate error it's an unknown certificate error in so much as I can't figure out where the certificate comes from. This happens on a Win 7 Enterprise machine connecting to Exchange 2010 with Outlook 2010. The error he gets is that the root is not trusted because it's a self-signed cert. Take a look at this screenshot because even if I had generated this myself I wouldn't have put "SomeOrganizationalUnit" or "SomeCity" or "SomeState", etc. (Red block covers our domain name.) I'm a little concerned this is a symptom of a security breach. Exchange 2010 has three certificates installed but none of them are this certificate. They all have different expiration dates (one is expired) and different meta-data. edit: There are two scenarios that I see the certificate warning and one of them I can reliably repeat. When the user leaves his computer on over night Outlook pops the Security Warning window. I don't know what time this happens. Using Outlook Anywhere if I connect to Exchange externally via a cellular USB modem the Security Warning window will appear every time I close and reopen Outlook. Whether I say Yes or No does not make a difference on whether or not I can connect to Exchange and send/receive email. In other words, I can always connect to Exchange. I've checked my two Exchange servers and my Cisco router for a certificate that matches this one and I can't find it. edit 2: Here is a screenshot of the Security Alert window. (I've been calling it Security Warning... My mistake.) edit 3: I stopped seeing this error several weeks ago but I can't tie it to any single event (because I just sort of realized that warning had stopped showing up) but I think I found the source of the certificate. Last week I found out that the certificate on our website DomainA.com was invalid. I knew that our web admin had installed a valid certificate so when I look into the problem I found out I was being presented with the invalid certificate that this posting is in regards to. The Exchange server's domain is mail.DomainA.com so I can only guess that Outlook was passing this invalid certificate through as it did some kind of check on DomainA.com. This issue is still a mystery because the certificate warning stopped appearing several weeks ago whereas the invalid certificate issue on the website was only fixed last week. It ended up being a problem with the website control panel. The valid certificate was installed but not being served for some reason and instead the self-signed cert was being served.

  Read the article

• Why did Intel drop the Itanium?

  - by Cole Johnson

  I was reading up on the history of the computer and I came along the IA-64 (Itanium) processors. They sounded really interesting and I was confused as to why Intel would decide to drop them. The ability to choose explicitly what 2 instructions you wanted to run in that cycle is a great idea, especially when writing your program in assembly, for example, a faster bootloader. The hundreds of registers should be convincing for any assembly programmer. You could essentially store all the functions variables in the registers if it doesn't call any other ones. The ability to do instructions like this: (qp) xor r1 = r2, r3 ; r1 = r2 XOR r3 (qp) xor r1 = (imm8), r3 ; r1 = (imm8) XOR r3 versus having to do: ; eax = r1 ; ebx = r2 ; ecx = r3 mov eax, ebx ; first put r2 into r1 xor eax, ecx ; then set r1 equivalent to r2 XOR r3 or ; SAME mov eax, (imm32) ; first put (imm32) into r1 xor eax, ecx ; then set r1 equivalent to (imm32) XOR r3 I heard it was because of no backwards x86 comparability, but couldn't thy be fixed by just adding the Pentium circuitry to it and just add a processor flag that would switch it to Itanium mode (like switching to Protected or Long mode) All the great things about it would have surly put them a giant leap ahead of AMD. Any ideas? Sadly this means you will need a very advanced compiler to do this. Or even one per specific model of the CPU. (E.g. a newer version of the Itanium with an extra feature would require different compiler). When I was working on a WinForms (target only had .NET 2.0) project in Visual Studio 2010, I had a compile target of IA-64. That means that there is a .NET runtime that was able to be compiled for IA-64 and a .NET runtime means Windows. Plus, Hamilton's answer mentions Windows NT. Having a full blown OS like Windows NT means that there is a compiler capable of generating IA-64 machine code.

  Read the article

• Does 64bit Windows 8 have the same 75% memory-usage limitation for applications as Windows 7?

  - by Barleyman

  64bit Windows 7 (and Windows Vista) have a built-in limit of not being able to use the last 25% of RAM. You will get a low memory warning when you get close to the limit. Even if you disable that warning, applications will run out of memory and crash since the OS will refuse to allocate memory from that last 25%. That was fine when Vista was designed, when machines had 1 GB of total memory, but is pretty daft for today's 8 GB machines. Yes, the system will run cache, etc. on that extra 2 GB, but running out of memory when you have "merely" 2 GB left.... NB: this has nothing to do with the page file. If you limit the page file to a sensible size like 2 GB, you will still see this behavior. The system will cram the page file to the last byte while refusing to touch that 1/4th of the RAM. Does Windows 8 change this behavior? Is there now some fixed minimum free RAM requirement, like 512 MB, or is it still 25%? Can you actually adjust the low memory limit? EDIT: Here is another older post here which discusses this same behavior on Windows 7. There is fixed 25% limit in Windows 7 and I'd like to know if it's still in Windows 8. Windows 7 / Page File Disabled / 12 GB RAM / 2+ GB RAM free and "your computer is running low on memory" Edit2: Here is another link discussing the low memory warning and how to disable it. Note he claims the limit for RAM usage is 80%, not 75%. It would seem to be correct as you can in fact allocate 6.4GB of RAM with 8GB machine. Anything above and beyond that goes to the pagefile, though. http://halflight.com.au/2011/04/06/how-to-disable-low-memory-warnings-and-the-advantages-of-removing-the-page-file/ Edit3: a Here's couple of process explorer screenshots that demonstrate how it goes down. Exhibit1: https://dl.dropbox.com/u/42068601/sysinfo.jpg Exhibit2: https://dl.dropbox.com/u/42068601/sysint2.jpg You can see that Windows 7 will use the memory 6.4GB as the very last resort. I have low memory warning switched off here so programs crashed at the last screenshot allocation. With low memory warning turned on, it starts nagging before you can push OS to use that remaining 1.6GB. The question is not "Is it OK windows does not want to allocate last 20% of RAM because X", it's "Does Windows 8 still behave this way". With 16GB this really becomes dumb.

  Read the article

• PHP `virtual()` with Apache MultiViews not working after upgrade to Ubuntu 12.04

  - by Izzy

  I use PHP's virtual() directive quite a lot on one of my sites, including central elements. This worked fine for the last ~10 years -- but after upgrading (or rather moving, as it is on a new machine) to Ubuntu 12.04 it somehow got broken. Example setup (simplified) To make it easier to understand, I simplify some things (contents). So say I need a HTML fragment like <P>For further instructions, please look <A HREF='foobar'>here</P> in multiple pages. 10 years ago, I used SSI for that, so it is put into a file in a central place -- so if e.g. the targeted URL changes, I only need to update it in one place. To serve multiple languages, I have Apache's MultiViews enabled -- and at $DOCUMENT_ROOT/central/ there are the files: foobar.html (English variant, and the default) foobar.html.de (German variant). Now in the PHP code, I simply placed: <? virtual("/central/foobar"); ?> and let Apache take care to deliver the correct language variant. The problem As said, this worked fine for about 10 years: German visitors got the German variant, all others the English (depending on their preferred language). But after upgrading to Ubuntu 12.04, it no longer worked: Either nothing was delivered from the virtual() command, or (in connection with framesets) it even ended up in binary gibberish. Trying to figure out what happens, I played with a lot of things. I first thought MultiViews was (somehow) not available anymore -- but calling http://<server>/central/foobar showed the right variant, depending on the configured language preferences. This also proved there was nothing wrong with file permissions. The error.log gave no clues either (no error message thrown). Finally, just as a "last ressort", I changed the PHP command to <? virtual("central/foobar.html"); ?> -- and that very same file was in fact included. So PHP's virtual() function basically worked -- but the language dependend stuff obviously did no longer work together with it as it did before. Of course I tried to find some change (most likely in PHP's virtual() command), using Google a lot, and also searching the questions here -- unfortunately to no avail. Finally: The question Putting "design questions" aside (surely today I would design things differently -- but at least currently I miss the time to change that for a quite huge amount of pages): What can be done to make it work again? I surely missed something -- but I cannot figure out what...

  Read the article

• How do I (robustly) remotely execute tasks on Windows workstations in a domain?

  - by Zac B

  I'm not even sure if "robustly" is a word. Anyway. Context: We have a few hundred Windows 7 workstations on a LAN. We use AD/GPO management pretty heavily, but there are a lot of periodic and/or manual maintenance tasks we need to do that can't be done via GPO/scheduled task. For example, say I want to execute program X (which runs silently, in the background, and doesn't bother the user) on workstation Y, or say I want to execute task A on a workstation group B either on a schedule or on demand. Kicking the users off of their computers to do this (i.e. using RDP) is a no-no, and doesn't work on groups anyway. Question: What's the best way to do this that is robust enough that, after setup, I could give it to beginner support people (read: people who are phobic of the command line, and get confused with GUI interfaces more complicated than Firefox)? I'm a competent programmer, and, if there is a robust set of tools or framework out there for this type of task, I'd consider hacking something together myself if it didn't take too long. If there's some combination of tools or techniques that others use to make remote-workstation-administration doable by beginners, I have yet to find it. For those who care about the "why": I'm midlevel IT, and was told to implement a remote management solution that allows arbitrary/scheduled remote execution, with confirmation that programs actually ran remotely, and the ability to view what they returned. "Why?" I asked, "Can't I just use PsExec and the task scheduler on a dispatcher machine?" "No," I was told, "'Joe' the second-week tech is going to be in charge of this one, and he needs something simple with a GUI." What I've tried: I've played with making a bunch of one-clickable "transfer files to remote computer and run them with PsExec" batch/VB scrips, but those tend to break down and don't easily support running on customizable groups. I've played a little bit with the Windows version of Puppet, but it doesn't support arbitrary-time remote execution (it's ability to group computers into a tree/node structure is really nice though). I've used an older version of Altiris, and, while it does a lot of what I want, it's interface is awful, it's slow, crashes a lot, and is probably too expensive for management. SwiftWater's DMS solution does some of what I want, but it's very underdeveloped, closed-source (not a deal breaker but not ideal), and I get the impression that support and reliability are lacking.

  Read the article

• git, egit, submodules, and symlinks -- how should shared sub-projects be handled in eclipse?

  - by Autophil

  Here's the situation. I have a few git projects with a directory structure layed out more or less like this: simpleproj app www admin demo lib model orm view model user blah ... storeproj app www about mobile fbapp lib model orm view model user message cart product merchant Each directory in "lib" contains a separate project, either created in-house or forked, all of which use git for source control. So I figured I should make them submodules of my projects, right? Well, we've been moving toward eclipse + egit, because some of our windows guys not used to a CLI need something they can use without being scared of screwing things up. Anyway, the problem is, egit doesn't support submodules. So, my solution has been a rather crude one involving symlinks... lets say my directory structure on my dev box is generally layed out like this: ~/projects/ bigproj .git app lib model (- ~/lib/model/src/) orm (- ~/lib/orm/src/) neatproj .git app lib view (- ~/lib/view/src/) oldproj .git app lib orm (- ~/lib/orm/src/) ~/lib/ model .git src README.md orm .git src COPYING view .git src ...the symlinks link inside of directory with the git repo, so eclipse doesn't get confused, and everything sort of works. On my machine, I can update the libs from anywhere and all projects will be updated (needing to be committed again of course). Each project stores a separate copy of the contents of the symlinked directories within "lib" -- but only when staged from within eclipse. After committing from eclipse and moving back to the CLI, git sees that a bunch of files have been removed and a few symlinks have been created. Of course this is acceptable also, probably more so than keeping a separate history of the libs for each project... but eclipse and CLI git obviously need to be on the same page so tons of files aren't vanishing and reappearing. So this brings me to my question. I'd like to know how to either: get eclipse+egit to see the symlinks as symlinks if git will somehow handle them properly*, or get the CLI git to treat them as non-symlinks. Or, if there's a better way to do this, I'm all ears. Hope this all made sense! :D Note: tried to tag this as git-submodules, but was not allowed :( * should I make them relative or absolute? Either way it's a mess. Also will symlinks will work on windows? i know there's something similar but you need a 3rd party tool to manage them AFAIK, i doubt these would translate well.

  Read the article

• Unable to boot from LiveCD/USB and even Super Grub Disk!

  - by Reuben L.

  Hi all, I'm in a fix. Basically this morning, I decided to format my Win7 as it was getting really slow and I did so with no problems. I also have a Linux Mint OS on dual boot. Since I was springcleaning my windows partition, I decided it was a good idea to do the same to my linux partition. I downloaded the latest version of Linux Mint (Julia) and burned the LiveCD. Now here is where the problem lies, when I restarted Windows and chose to boot from the LiveCD, it didn't work. No joke. There was just a little underscore blinking for a long time before it went back to GRUB which prompted me to select an OS to boot. However, when I went into my old Linux Mint OS and restarted the machine, the LiveCD worked... to a certain extent. It would load and look as though it was ready to install Linux Mint 10 but the moment it got to the option screen, the whole screen turned into a checkered and jumbled mess. At this point I thought it was the LiveCD or the .iso file. I had an Ubuntu LiveUSB for recovery purposes and I tried that. The exact same thing happened. Can't boot the LiveUSB if I restarted from Windows, but works when I reboot from Linux. BUT still the same checkered screen that doesnt respond. Did a bit of googling and reckoned it might be something wrong with my GRUB. Did some updating and didnt make a difference. Then I tried the Super Grub Disk and STUPIDLY uninstalled GRUB. (Note that booting to SGD had the exact same problem - can't be done if I rebooted from Windows). Now I can't access my Linux Mint 9 cos the the bootup screen (mbr) only has Windows 7 as an option. Remember me mentioning that I can't boot from any CD/USB/recovery CD when I reboot from Windows? And now that I can't access Linux, there's no way for me to do any form of recovery! I've tried using the command prompt utility at startup recovery but to no avail. Anyone can help me with this?

  Read the article

• recommendations for efficient offsite remote backup solution of vm's

  - by senorsmile

  I am looking for recommendations for backing up my current 6 vm's(and soon to grow to up to 20). Currently I am running a two node proxmox cluster(which is a debian base using kvm for virtualization with a custom web front end to administer). I have two nearly identical boxes with amd phenom II x4's and asus motherboards. Each has 4 500 GB sata2 hdd's, 1 for the os and other data for the proxmox install, and 3 using mdadm+drbd+lvm to share the 1.5 TB's of storage between the two machines. I mount lvm images to kvm for all of the virtual machines. I currently have the ability to do live transfer from one machine to the other, typically within seconds(it takes about 2 minutes on the largest vm running win2008 with m$ sql server). I am using proxmox's built-in vzdump utility to take snapshots of the vm's and store those on an external harddrive on the network. I then have jungledisk service (using rackspace) to sync the vzdump folder for remote offsite backup. This is all fine and dandy, but it's not very scalable. For one, the backups themselves can take up to a few hours every night. With jungledisk's block level incremental transfers, the sync only transfers a small portion of the data offsite, but that still takes at least a half an hour. The much better solution would of course be something that allows me to instantly take the difference of two time points (say what was written from 6am to 7am), zip it, then send that difference file to the backup server which would instantly transfer to the remote storage on rackspace. I have looked a little into zfs and it's ability to do send/receive. That coupled with a pipe of the data in bzip or something would seem perfect. However, it seems that implementing a nexenta server with zfs would essentially require at least one or two more dedicated storage servers to serve iSCSI block volumes (via zvol's???) to the proxmox servers. I would prefer to keep the setup as minimal as possible (i.e. NOT having separate storage servers) if at all possible. I have also briefly read about zumastor. It looks like it could also do what I want, but it appears to have halted development in 2008. So, zfs, zumastor or other?

  Read the article

• How to get the best LINPACK result and conquer the Top500?

  - by knweiss

  Given a large Linux HPC cluster with hundreds/thousands of nodes. What are your best practices to get the best possible LINPACK benchmark (HPL) result to submit for the Top500 supercomputer list? To give you an idea what kind of answers I would appreciate here are some sub-questions (with links): How to you tune the parameters (N, NB, P, Q, memory-alignment, etc) for the HPL.dat file (without spending too much time trying each possible permutation - esp with large problem sizes N)? Are there any Top500 submission rules to be aware of? What is allowed, what isn't? Which MPI product, which version? Does it make a difference? Any special host order in your MPI machine file? Do you use CPU pinning? How to you configure your interconnect? Which interconnect? Which BLAS package do you use for which CPU model? (Intel MKL, AMD ACML, GotoBLAS2, etc.) How do you prepare for the big run (on all nodes)? Start with small runs on a subset of nodes and then scale up? Is it really necessary to run LINPACK with a big run on all of the nodes (or is extrapolation allowed)? How do you optimize for the latest Intel/AMD CPUs? Hyperthreading? NUMA? Is it worth it to recompile the software stack or do you use precompiled binaries? Which settings? Which compiler optimizations, which compiler? (What about profile-based compilation?) How to get the best result given only a limited amount of time to do the benchmark run? (You can block a huge cluster forever) How do you prepare the individual nodes (stopping system daemons, freeing memory, etc)? How do you deal with hardware faults (ruining a huge run)? Are there any must-read documents or websites about this topic? E.g. I would love to hear about some background stories of some of the current Top500 systems and how they did their LINPACK benchmark. I deliberately don't want to mention concrete hardware details or discuss hardware recommendations because I don't want to limit the answers. However, feel free to mention hints e.g. for specific CPU models.

  Read the article

• Trying to setup virtual hosts on unix PHP on nginx

  - by user1634653

  I have tried to install php5-fpm and Nginx on Ubuntu machine, but I got a problem. When I have only one virtual host on a unix port it is all fine but when I try to add another virtual host Nginx goes to default web page "Welcome to Nginx!" but when I run it on a tcp port example port 9000 it work fine with multisites. It is a fresh install of ubuntu 11.10, Nginx 1.2.3 with php5-fpm installed. It also has extra php installs such as php-apc. I can only give the links to the virtual hosts because I am doing it from a mobile phone. Here are the links for the two virtual hosts I am using: http://ic0nic.co.uk/ic0nic.txt, http://ic0nic.co.uk/sourproxy.txt also I want to use unix port because I find it a whole lot faster. Edit: Here are the nginx configs server { server_name ic0nic.co.uk www.ic0nic.co.uk; root /var/www/ic0nic.co.uk; listen 8080; index index.html index.htm index.php; include conf.d/drop; location / { try_files $uri $uri/ /index.php?q=$uri&$args; } location ~ \.php$ { fastcgi_buffers 8 256k; fastcgi_buffer_size 128k; fastcgi_intercept_errors on; include fastcgi_params; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_pass unix:/dev/shm/php-fpm-www.sock; root /var/www/ic0nic.co.uk; } } server { server_name sourproxy.co.uk www.sourproxy.co.uk; root /var/www/sourproxy.co.uk/; listen 8080; index index.html index.htm index.php; include conf.d/drop; location / { try_files $uri $uri/ /index.php?q=$uri&$args; } location ~ \.php$ { fastcgi_buffers 8 256k; fastcgi_buffer_size 128k; fastcgi_intercept_errors on; include fastcgi_params; fastcgi_param SCRIPT_FILENAME /var/www/sourproxy.co.uk$fastcgi_script_name; fastcgi_pass unix:/dev/shm/php-fpm-www.sock; } }

  Read the article

• How do you backup 40+ Centos5.5 servers?

  - by John Little

  We are embarrassed to ask this question. Apologies for our lack of UNIX expertise. We have inherited 40+ centos 5.5 servers, and don't know how to back them up. We need low level clone type images so that we could restore the servers from scratch if we had to replace the HDs etc. We have used the "dd" command, but we assume this only works if you want to back up one local disk to another, not 40 servers to one server with an external USB HD attached. All 40 servers have a pair of mirrored disks (dont know if its HW or SW raid). Most only have 100MB used. SErvers are running apache, zend, tomcat, mysql etc. Ideally we dont want to have to shut them down to backup (but could). We assume that standard unix commands like tar, cpio, rsync, scp etc. are of no use as they only copy files, not partitions, all attributes, groups etc. i.e. do not produce a result which can simply be re-imaged to a new HD to get the serer back from dead. We have a large SAN, a spare windows box and spare unix boxes, but these are only visible to one layer in the network. We have an unused Dell DL2000 monster tape unit, but no sw or documentation for it. WE have a copy of symantec backup exec, but we have no budget for unix client licenses. (The company has negative amounts of money). We need to be able to initiate the backup remotely, as we can only access the servers in person in an emergency (i.e. to restore) Googling returns some applications to do this, e.g. clonezilla - looks difficult to install and invasive. Mondo, only seems to support backup if you are local to the machine. Amanda might be an option, but looks like days/weeks of work to learn and setup? Is there anything built into Centos, or do we have to go the route of installing, learning and configuring a set of backup softwares? Any ideas? This must be a pretty standard problem which goggling doesnt give an obvious answer.

  Read the article

• SSH Connection Refused - Debug using Recovery Console

  - by olrehm

  Hey everyone, I have found a ton of questions answered about debugging why one cannot connect via SSH, but they all seem to require that you can still access the system - or say that without that nothing can be done. In my case, I cannot access the system directly, but I do have access to the filesystem using a recovery console. So this is the situation: My provider made some kernel update today and in the process also rebooted my server. For some reason, I cannot connect via SSH anymore, but instead get a ssh: connect to host mydomain.de port 22: Connection refused I do not know whether sshd is just not running, or whether something (e.g. iptables) blocks my ssh connection attempts. I looked at the logfiles, none of the files in /var/log contain any mentioning on ssh, and /var/log/auth.log is empty. Before the kernel update, I could log in just fine and used certificates so that I would not need a password everytime I connect from my local machine. What I tried so far: I looked in /etc/rc*.d/ for a link to the /etc/init.d/ssh script and found none. So I am expecting that sshd is not started properly on boot. Since I cannot run any programs in my system, I cannot use update-rc to change this. I tried to make a link manually using ln -s /etc/init.d/ssh /etc/rc6.d/K09sshd and restarted the server - this did not fix the problem. I do not know wether it is at all possible to do it like this and whether it is correct to create it in rc6.d and whether the K09 is correct. I just copied that from apache. I also tried to change my /etc/iptables.rules file to allow everything: # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *mangle :PREROUTING ACCEPT [7468813:1758703692] :INPUT ACCEPT [7468810:1758703548] :FORWARD ACCEPT [3:144] :OUTPUT ACCEPT [7935930:3682829426] :POSTROUTING ACCEPT [7935933:3682829570] COMMIT # Completed on Thu Dec 10 18:05:32 2009 # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *filter :INPUT ACCEPT [7339662:1665166559] :FORWARD ACCEPT [3:144] :OUTPUT ACCEPT [7935930:3682829426] -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 25 -j ACCEPT -A INPUT -p tcp -m tcp --dport 993 -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m tcp --dport 143 -j ACCEPT -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 8080 -s localhost -j ACCEPT -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 -A INPUT -j ACCEPT -A FORWARD -j ACCEPT -A OUTPUT -j ACCEPT COMMIT # Completed on Thu Dec 10 18:05:32 2009 # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *nat :PREROUTING ACCEPT [101662:5379853] :POSTROUTING ACCEPT [393275:25394346] :OUTPUT ACCEPT [393273:25394250] COMMIT # Completed on Thu Dec 10 18:05:32 2009 I am not sure this is done correctly or has any effect at all. I also did not find any mentioning of iptables in any file in /var/log. So what else can I do? Thank you for your help.

  Read the article

• What are the most likely bottlenecks determining the performance of CamStudio screen recording?

  - by Steve314

  When doing screen recording, I can get a frame rate of maybe 15 frames per second for the full screen on my 1080p monitor using the XVID codec. I can increase the speed a bit by recording a region, changing screen modes, and tweaking other settings, but I'm curious what hardware upgrades might give me the biggest bang for my buck. My PC is budget, but modern... Athlon 2 X4 645 (3.1GHz, quad core, limited cache) processor. 4GB single channel DDR3 1066 RAM. ASRock motherboard with NVidia GeForce 7025/nForce 630a Chipset. ATI Radeon HD 5450 graphics card - 512MB on board, not configured to steal system RAM. I dual-boot Windows XP and Windows 7. For the moment, XP is my bigger performance concern as it's still my getting-things-done O/S as opposed to my browser-host O/S. My goal is to make a few programming-related tutorials. For a lot of that I don't need screen recording - I can make up some slides, record audio with the PC switched off, yada yada. When I do need screen recording, I'll mostly be recording Notepad++, Visual Studio or a command prompt. Occasionally, I may be recording some kind of graphics or diagram program and using my pre-Bamboo cheap Wacom tablet - I have the CS2 versions of Photoshop and Illustrator, but I'd much more likely be using Microsoft Paint. Basically, what I'll be recording won't be making huge demands on the machine - but recording a fair number of pixels (720p preferred) will be useful. What's particularly wierd - not so long ago I still had a five-year-old Pentium 4 based PC. And (with the same 1080p monitor) it could record at not far from the same frame rate. So clearly the performance issues are more subtle than just throw-money-at-it. My first guess would be that the main bottleneck is the bandwidth for transferring data to/from the graphics card. Is that likely to be correct? In support of that, see this [Radeon HD 5450 review][1] - the memory bandwidth is only 12.8 GB/s. If you can't get data out of graphics memory quickly, you can't transfer it back to the system memory quickly. Apparently, that's slower than some top-end cards in 2002.

  Read the article

• Model M Keyboard inputs incorrect characters after logging in to Fedora

  - by mickburkejnr

  I recently bought a 24 year old IBM Model M keyboard. From what I gather, it'd been left on a shelf for the last 5 years, so you can imagine the amount of dust dirt and crap that was on it. Before cleaning it, I plugged it in to my laptop (running Fedora 17) using a PS/2 to USB adapter. What I found was, while it still works, the keys I press don't correspond to what is displayed on the screen. So for example, when I type S on the keyboard, I get ß display on the screen instead. At the time, I put this down to the adapter not working properly. Since then, I stripped the keys off the keyboard and cleaned the whole thing. It looks like it's just come out of a box! I then plugged it in to my computer (also running Fedora 17) via a standard PS/2 plug. The computer loaded up to the login screen, and I typed in my password. Pressed enter, and I logged straight in to my machine. At this point, I opened up a text editor and started typing some stuff. To my horror, the keystrokes I was entering weren't coming up as intended. What came up instead were characters that would map to the pressed key but only under a different keyboard language setting. I opened up a program to see what keyboard language had been selected, and the correct one for the keyboard was selected (which is UK in my case). I opened up a window that would show what characters mapped to what keys, and I pressed every single key on the keyboard, and every corresponding block representing each key lit up. I went back to the text editor to try again, but I was still getting these random characters. Whats more is that the backspace key would not work, although in the other utility it would flash when pressed. What I know is that at the login screen the keyboard must have entered the correct characters, otherwise I wouldn't have been able to log in. Further more, keys that don't respond while using a text editor as sending signals to the computer, as illustrated in that keyboard utility. The question is why random characters are displayed when they really shouldn't be? Would this be a hardware fault or a software issue?

  Read the article

• How to use AD/GPO/Print Services to "push out" a new printer driver to replace a broken one? How did my server get a broken driver?

  - by Zac B

  Context: We have an AD/GPO-managed corporate network with a little over a hundred PCs running Windows 7 x64, and a few managed printers. Our Server2008R2 primary domain controller is configured as a print server for them all. Problem: After a recent windows update and restart (no printer driver updates were included) on the DC, a particular shared printer (Lexmark T650) has begin exhibiting some strange behavior. First, it prints a preceding and following blank page for almost every document, on jobs submitted by about half of client machines (no separator page is configured on the server or any of the clients I've seen). Second, whenever someone tries to access "Printing Preferences" on any client, they recieve the following error message (this happens everywhere, 100% of the time, and didn't happen before the update on the DC): Once they click "OK", the prefs screen appears (with no separator page selected) and everything seems fine. I'm not even sure if these two issues are related, but everyone seems affected by one or both of those issues. What I've Tried: I've been hesitant to un-deploy the problem printer, or remove it via GPO, as it's pretty heavily used. I've tried updating (via MS update and our internal WSUS server) client machines and the DC. No printer driver updates have appeared, and no number of updates or restarts on the server or the client seems to have achieved anything other than my boss getting grumpy that I'm bouncing the domain controller so often. I've tried deleting the drivers on the server, and re-installing them from the original source that has worked for the past year...no change. I've tried selecting "New Driver" for one of the shared printers on a client machine, running as domain admin, and pushed the latest driver found by MSupdate back up to the DC. This changed the version number of the driver recorded in the print server manager, but caused no change--on the client I pushed from, or on any other. The error still appears. Question: Why the heck is this happening? Obviously, I got a bad driver from somewhere, but how do I get rid of it? I don't know of any "roll back drivers" functionality for centrally managed print drivers like Windows offers for other devices. How would I a) get this issue resolved on a client, and b) push the fix to the other members of the domain?

  Read the article

• Triple monitor setup in linux

  - by Brendan Abel

  I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

  Read the article

• Windows 8 disk errors

  - by wrongusername

  So yesterday, I forcibly restarted my Windows 8 PC. VMWare Workstation was having some trouble with the guest Linux Mint OS. It wasn't responding for some time, so I tried suspending it September 28th or perhaps even before. It wouldn't suspend -- I forgot what the window looked like, but all options in the power menu were disabled (i.e. "Shutdown," "Power Off," and options like that were all disabled). I eventually killed the VMWare application through Task Manager, though I was too lazy to hunt down the running virtual machine itself, and decided to kill it by just shutting down my PC entirely. The PC wouldn't shut down for quite some time after the monitor went blank, so I did a cold reset by holding the power button. I then powered it on again and Windows briefly gave me some message like "Search for KERNEL_STACK_INPAGE_ERROR." Windows then started diagnosing some problems and gave me the message, "Repairing disk errors. This might take over an hour to complete." That was yesterday night, and I went to sleep without waiting for it to finish. This morning, it said that the repair failed, and that the log was at C:\windows\system32\LogFiles\srt\srtTrail.txt (as I remember it -- I don't have the exact path I wrote down right now). It gave me some other options to troubleshoot, such as resetting Windows (files and settings still intact, but programs not installed through the app store will be erased). That didn't work (no error message given, I was just told it didn't work). I tried rebooting in safe mode, the same diagnosis process begins, except that this time it doesn't bother with the automatic repairs again. So I tried using the command prompt to try to see if my files are at least still there. I was on the X drive, and I couldn't cd to the C drive. I couldn't find my folder under Users (of course?), and couldn't find the srt folder under LogFiles either. I am not sure what to try next. I have backed up everything, but to the cloud, so if absolutely necessary I can start off with a fresh copy of Windows and restore all my data, though it would be a hassle. Any thoughts on what might be wrong or what I can try? My computer was purchased just this June, so the hard drive should still be pretty new.

  Read the article

• Mouse Error Code 24. Windows 7

  - by Cj.

  I've had the same mouse for a while, and it's been working fine until one day, it started giving me a message about a device not working properly. I tried updating the drivers, and re-installing, I even deleted old drivers in case my computer should be a little confused. It never made a difference, and my mouse seemed to be working just fine despite getting the permanent error in my device manager, I looked it up several times online, but I never found anything I could actually use, when I go to official websites, I always get the same response "plug in so so into a different place - drivers - install silverlight before you can watch this tutorial, try it on a different machine". so I gave up on that. But now is where I have a real problem, lately, my little strange error evolved into a fullblown Error 24, and my mouse is starting to turn on and off randomely, especially when it is being used, but I do hear it go "badum..dadum" when I'm off doing something else. when I looked up error code 24, I really didn't find much other than it meaning: Code 24 This device is not present, is not working properly, or does not have all its drivers installed. (Code 24) Cause The device is installed incorrectly. The problem could be a hardware failure, or a new driver might be needed. Devices stay in this state if they have been prepared for removal. After you remove the device, this error disappears. But, I have tried uninstalling the device entirely several times, and it'll go right back to its previous state with error 24, and turning on and off randomely. what do I do? I cannot afford taking it to a repair place, I can't really afford a new mouse either, I refuse to buy cheap ones as I am a gamer, in need of more than 3 buttons, and a good grip is important. Could there possibly be some confusion in the registry? I do remember having gotten some early problems after I converted my vista to windows7. But I hardly dare going in there unless I'm 100% certain of what I'm going for, and I can honestly say I am at a loss here. Edit: it is a USB mouse we're talking about here. MX™518 Optical Gaming Mouse (logitech) Edit2: I am seeing no rupture, so it must be on the inside of my mouse, or inside the rubber, protecting the cable, that would be really inconvenient to search for

  Read the article

• Google Chrome and Firefox Rendering

  - by user13503

  When attempting to visit sites running javascript, Google Chrome and Firefox often fail to render them properly. For example, when hitting google.com/codesearch results, I just get a blank page. http://img340.imageshack.us/img340/8527/200910071518.png This rendering problem happens in both browsers on a machine running Windows XP Professional x64. Internet explorer is able to render the page just fine. Also, controls on other pages sometimes fail to respond, for example in Google Docs. Has anyone encountered this issue before in Chrome/Firefox? Do they share a common installation of the V8 javascript engine? I'm baffled by this issue. Here's the source code for the image above that Chrome loads when attempting to retrieve the page: <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd"><html><head><script>function a(c){this.t={};this.tick=function(d,e,b){var f=b?b:(new Date).getTime();this.t[d]=[f,e]};this.tick("start",null,c)}var g=new a;window.jstiming={Timer:a,load:g};try{window.jstiming.pt=window.external.pageT}catch(h){}; </script><title></title><script language="javascript" src="/codesearch/js/CachedFile/F1A2CB189D0FCB1FF201C42BF6A5447C.cache.js"></script></head><body><iframe src="javascript:''" id="__gwt_historyFrame" style="width:0;height:0;border:0"></iframe><script>if(window.jstiming){window.jstiming.a={};window.jstiming.c=1;function k(a,d,f){var b=a.t[d];if(!b)return undefined;b=a.t[d][0];if(f!=undefined)var h=f;else h=a.t.start[0];return b-h}window.jstiming.report=function(a,d,f){var b="";if(window.jstiming.pt){b+="&srt="+window.jstiming.pt;delete window.jstiming.pt}try{if(window.external&&window.external.tran)b+="&tran="+window.external.tran}catch(h){}if(a.b)b+="&"+a.b;var e=a.t,p=e.start,l=[],i=[];for(var c in e)if(!(c=="start"))if(!(c.indexOf("_")==0)){var j= e[c][1];if(j)e[j]&&i.push(c+"."+k(a,c,e[j][0]));else p&&l.push(c+"."+k(a,c))}delete e.start;if(d)for(var m in d)b+="&"+m+"="+d[m];var n=[f?f:"http://csi.gstatic.com/csi","?v=3","&s="+(window.jstiming.sn?window.jstiming.sn:"codesearch")+"&action=",a.name,i.length?"&it="+i.join(",")+b:b,"&rt=",l.join(",")].join(""),g=new Image,o=window.jstiming.c++;window.jstiming.a[o]=g;g.onload=g.onerror=function(){delete window.jstiming.a[o]};g.src=n;g=null;return n}}; </script></body></html> Thanks, Steve

  Read the article

• Trying to get DNS services running on Windows Server 2008 R2, what am I getting wrong ?

  - by LaserBeak

  Ok, So I am basically trying to get a home server pc up that will provide Domain name services, act as Mail server and web server. I have one static IP, well it's not officially static but hasn't changed in two years so I'll call it static. I have done the following: Configured router NAT/virtual port forward UDP/TCP port 53 to the internal IP of my server 192.168.1.16, in adapter settings specified the manual settings: 192.168.1.16 IP, gateway 192.168.1.1, Subnet: 255.255.255.0 and loopback DNS: 127.0.0.1 Using my public my public IP Checked using http://www.canyouseeme.org/ that port 53 is open and is not being blocked by my ISP. It can see services on this port. Registered Domain name (mydomain.com.au) Updated whois database through the domain registrars site and registered NameServer names: ns0.mydomain.com.au and ns2.mydomain.com.au, both have been associated with my single public IP. (Waited 24 hours) Update the nameserver for mydomain.com.au: primary ns0.mydomain.com.au secondary: ns2.mydomain.com.au (waited 24+ hours) Installed Server 2008 R2, install web server role and DNS role. Webserver works when I enter my public IP into browser of any PC/mobile, get IIS7 welcome page. In DNS server: Created new forward lookup zone: ; ; Database file mydoman.com.au.dns for mydomain.com.au zone. ; Zone version: 10 ; @ IN SOA mydomain.com.au. mydomain.testdomain.com. ( 10 ; serial number 900 ; refresh 600 ; retry 86400 ; expire 3600 ) ; default TTL ; ; Zone NS records ; @ NS ns0.mydomain.com.au. @ NS ns1.mydomain.com.au. ; ; Zone records ; @ A 192.168.1.16 www A 192.168.1.16 The Domain name services will however not work, the whois database updated with ns0.mydomain.com.au etc. but when I type in my site name www.mydomain.com.au from an external machine it will not open site and I can't even ping it (Can't find host) When I check the ns0.mydomain.com.au NS record using a tool Like: http://www.squish.net/dnscheck/ I get: Security: Server ns0.mydomain.com.au (XXX.XXX.XXX.XX <- my public IP) is recursive Domain exists but there is no such record Any ideas, thanks...

  Read the article

• First time installing Linux/Apache - uanble to connect

  - by bob

  I's my first time installing Linux/Apache. I loaded CentOS and LAMPP on a machine attached to a LAN. Turned off http and mysql (because I didn't want conflict with LLAMPP) chkconfig httpd off chkconfig mysqld off then successfully LAMPP started with /opt/lampp/lampp start Starting XAMPP for Linux 1.7.3a... XAMPP: Starting Apache with SSL (and PHP5)... XAMPP: Starting MySQL... XAMPP: Starting ProFTPD... XAMPP for Linux started. Problem: Unable to connect - Firefox can't establish a connection to the server at 179.16.51.36. I need some pointers as to where to look next. No errors in error_log file (just some warnings) I can ping server. httpd.conf looks like this: ServerRoot "/opt/lampp" Listen 80 ServerAdmin [email protected] ServerName 179.16.51.36 DocumentRoot "/opt/lampp/htdocs" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/opt/lampp/htdocs"> Options Indexes FollowSymLinks ExecCGI Includes Order allow,deny Allow from all </Directory> ErrorLog logs/error_log LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog logs/access_log common </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "/opt/lampp/cgi-bin/" </IfModule> <IfModule cgid_module> </IfModule> <Directory "/opt/lampp/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig etc/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddHandler cgi-script .cgi .pl AddType text/html .shtml AddOutputFilter INCLUDES .shtml </IfModule> EnableMMAP off EnableSendfile off

  Read the article

• Logitech Optical Mouse Frozen In Middle of Windows XP Pro Screen

  - by Code Sherpa

  Hi. I have a Logitech Optical Mouse/Keyboard. I have been using them just fine with the system drivers for almost a year now. I recently updated my Kaspersky software and rebooted. Now the mouse is frozen in the middle of my screen. I am not able to login to the Windows XP Pro box that has the frozen mouse (because i can't work the mouse) but am able to remote desktop to this computer. Things I know / have tried: When I boot on the problem computer, I am able to use the keyboard, but not the mouse. I have installed the latest version of Logitech's SetPoint (with the updated drivers) on the problem computer (via remote desktop) and that didn't seem to matter. I bought new batteries for the mouse and that didn't matter. I have tried the mouse/keyboard on another computer and the mouse works just fine there. My suspicion is that the Kaspersky install has overwritten a driver of some sort. Things I have not done (and would appreciate detailed steps if you feel this is the way to go): 1) Uninstalled all the mouse drivers on the machine and reboot. Then, reinstall. Note: When I get to the Device Manager I don't see an option for Human Interface Devices (where the mouse device is). Here are my options: Computer, Disk Drives, DVD/CD-Rom drives, Floppy controllers, IDE ATA/ATAPI, Imaging devices, Network Adapters, Other devices, Ports, Processors, Sound, video, and gaming, System devices, USB controllers. Also, I should point out that Video Controller is the only thing under Other devices and it has a yellow exclamation mark. The same is true for all the items under Universal Serial Bus controllers. I think this means I have to update my BIOS but, since my mouse was working just fine without doing that, I don't think that is my problem. So, how do I get to my Mouse Device? 2) Update my BIOS. Note: As pointed out above, I don't think this matters as my mouse was working just fine under my computer's current BIOS version. Thanks for your help.

  Read the article

• Linux: find out what process is using all the RAM?

  - by Timur

  Before actually asking, just to be clear: yes, I know about disk cache, and no, it is not my case :) Sorry, for this preamble :) I'm using CentOS 5. Every application in the system is swapping heavily, and the system is very slow. When I do free -m, here is what I got: total used free shared buffers cached Mem: 3952 3929 22 0 1 18 -/+ buffers/cache: 3909 42 Swap: 16383 46 16337 So, I actually have only 42 Mb to use! As far as I understand, -/+ buffers/cache actually doesn't count the disk cache, so I indeed only have 42 Mb, right? I thought, I might be wrong, so I tried to switch off the disk caching and it had no effect - the picture remained the same. So, I decided to find out who is using all my RAM, and I used top for that. But, apparently, it reports that no process is using my RAM. The only process in my top is MySQL, but it is using 0.1% of RAM and 400Mb of swap. Same picture when I try to run other services or applications - all go in swap, top shows that MEM is not used (0.1% maximum for any process). top - 15:09:00 up 2:09, 2 users, load average: 0.02, 0.16, 0.11 Tasks: 112 total, 1 running, 111 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4046868k total, 4001368k used, 45500k free, 748k buffers Swap: 16777208k total, 68840k used, 16708368k free, 16632k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ SWAP COMMAND 3214 ntp 15 0 23412 5044 3916 S 0.0 0.1 0:00.00 17m ntpd 2319 root 5 -10 12648 4460 3184 S 0.0 0.1 0:00.00 8188 iscsid 2168 root RT 0 22120 3692 2848 S 0.0 0.1 0:00.00 17m multipathd 5113 mysql 18 0 474m 2356 856 S 0.0 0.1 0:00.11 472m mysqld 4106 root 34 19 251m 1944 1360 S 0.0 0.0 0:00.11 249m yum-updatesd 4109 root 15 0 90152 1904 1772 S 0.0 0.0 0:00.18 86m sshd 5175 root 15 0 90156 1896 1772 S 0.0 0.0 0:00.02 86m sshd Restart doesn't help, and, by they way is very slow, which I wouldn't normally expect on this machine (4 cores, 4Gb RAM, RAID1). So, with that - I'm pretty sure that this is not a disk cache, who is using the RAM, because normally it should have been reduced and let other processes to use RAM, rather then go to swap. So, finally, the question is - if someone has any ideas how to find out what process is actually using the memory so heavily?

  Read the article

< Previous Page | 708 709 710 711 712 713 714 715 716 717 718 719  | Next Page >