Search Results

Search found 18927 results on 758 pages for 'remote desktop'.

Page 716/758 | < Previous Page | 712 713 714 715 716 717 718 719 720 721 722 723  | Next Page >

  • How can I minimize the amount my router slows down my Internet connection speed?

    - by Lord Torgamus
    Background I'm working with what I assume is a pretty common Internet setup: a cable modem, a wireless router and a few Internet-connected devices. Lately, I've started being more demanding on my Internet connection, and noticed that using my router slows down my download speeds considerably. I just kind of dealt with it until Zune Marketplace on the Xbox 360 told me that a movie was going to take well over ten hours to download, and I just didn't want to wait that long. Good little scientist that I am, I tried to reduce the problem down to one variable. The test As a control, I turned off all the devices in the house that use wireless Internet, and unplugged all the wired devices except for the Xbox. I also power-cycled both the modem and the router. I then tried to download the movie again, and was told that it would still take over ten hours. Next, I unplugged the router, and connected the Xbox directly to the modem. The movie downloaded in just over one hour. As far as I can tell, this means that my ISP, other cable users near me, the remote servers, anything wireless-related and my machines' disk speeds can't be at fault. A similar experiment that replaced the Xbox with a wired laptop produced similar results. To me, this says "the router is responsible for things taking around ten times longer to download." My question I'd still prefer to use the router for a few reasons: it's a pain to connect and disconnect everything every time there's a big file to download direct connection to the modem isn't good for security only one machine can be connected directly to the modem at a time What can I do to have fast connection speeds while still using the router? I don't mind turning other machines off, as long as I don't have to mess with power and ethernet cables. EDIT : After asking this followup question and then this one, I installed dd-wrt on my router, and I seem to be getting higher and more consistent speeds. Perhaps more importantly, my memory use is fairly constant. I know this isn't an answer — which is why I'm not posting it as an answer — but it is how I resolved the situation, and hopefully it'll be helpful for someone.

    Read the article

  • Configuring Novel iPrint client on ubuntu 13.10

    - by Mahdi Sadeghi
    Recently I have struggled a lot to make Novel iPrint client to work on my laptop. I need it to use Follow Me printers in our university(you can take your print form any printer). Using this tutorial from Novel, I tried to convert the rpm package and install it on Ubuntu 13.04 & 13.10. The post install script from installing generated deb package had a typo which I saw in post install messages and I fixed that. Now I have the client running. To see the client UI I installed cinnamon desktop(because unity does not have system tray and old solutions did'nt work to whitelist Novel clinet). I have iPrint plugin installed on firefox as well(I copied the shared object files to plugin directories). I try installing printers from provided ipp URL(which lists available printers on the server) with no success. After clicking the printer name I see this: I have various errors: Formerly firefox used to asked my network username/password for installing SSL printer but now it returns this: iPrint Printer - The printer is currently not available. However I can install non-SSL version but the printer location is either empty or points to: file:///dev/null even if I change it to the exact address which I see on working machines still it prints nothing. I have tried the novel command line tool, iprntcmd to print. It is being installed at: /opt/novell/iprint/bin/ msadeghi@werkstatt:/opt/novell/iprint/bin$ ./iprntcmd --addprinter ipp://iprint.rz.hs-offenburg.de/ipp/Follow-me\ -\ IPP iprntcmd v05.04.00 Adding printer ipp://iprint.rz.hs-offenburg.de/ipp/Follow-me - IPP. Added printer ipp://iprint.rz.hs-offenburg.de/ipp/Follow-me - IPP successfully. It adds the printer with empty location and again no print. What I found interesting is the log file at ~/.iprint/errors.txt with strange errors which I hope somebody here can understand. When I try to install the SSL printer I receive these logs(note that HP is my local printer and has nothing to do with iprint): Thu Oct 31 11:02:03 2013 Trace Info: iprint.c, line 6690 Group Info: IPRINT-lib Error Code: 4096 (0x1000) User ID: 1000 Error Msg: iPrint Lib - Bad URI type supplied (not IPP:, HTTP:, or HTTPS:). Debug Msg: IPRINTInterpretURI for file:///dev/null - Unknown Port Type - file Thu Oct 31 11:02:03 2013 Trace Info: iprint.c, line 6800 Group Info: IPRINT-lib Error Code: 4096 (0x1000) User ID: 1000 Error Msg: iPrint Lib - Bad URI type supplied (not IPP:, HTTP:, or HTTPS:). Debug Msg: IPRINTInterpretURI for hp:/usb/HP_LaserJet_1018?serial=KP103A1 - No Port type specified Thu Oct 31 11:02:05 2013 Trace Info: iprint.c, line 6690 Group Info: IPRINT-lib Error Code: 4096 (0x1000) User ID: 1000 Error Msg: iPrint Lib - Bad URI type supplied (not IPP:, HTTP:, or HTTPS:). Debug Msg: IPRINTInterpretURI for file:///dev/null - Unknown Port Type - file Thu Oct 31 11:02:05 2013 Trace Info: iprint.c, line 6800 Group Info: IPRINT-lib Error Code: 4096 (0x1000) User ID: 1000 Error Msg: iPrint Lib - Bad URI type supplied (not IPP:, HTTP:, or HTTPS:). Debug Msg: IPRINTInterpretURI for hp:/usb/HP_LaserJet_1018?serial=KP103A1 - No Port type specified Thu Oct 31 11:02:06 2013 Trace Info: mydoreq.c, line 676 Group Info: CLIB Error Code: 0 (0x0) User ID: 1000 Error Msg: Success Debug Msg: MyCupsDoFileRequest - httpReconnect failed (0) Thu Oct 31 11:02:06 2013 Trace Info: mydoreq.c, line 1293 Group Info: CUPS-IPP Error Code: 1282 (0x502) User ID: 1000 Error Msg: iPrint Printer - The printer is currently not available. Debug Msg: MyCupsDoFileRequest - IPP SERVICE UNAVAILABLE Thu Oct 31 11:02:06 2013 Trace Info: iprint.c, line 6690 Group Info: IPRINT-lib Error Code: 4096 (0x1000) User ID: 1000 Error Msg: iPrint Lib - Bad URI type supplied (not IPP:, HTTP:, or HTTPS:). Debug Msg: IPRINTInterpretURI for file:///dev/null - Unknown Port Type - file Thu Oct 31 11:02:06 2013 Trace Info: iprint.c, line 6800 Group Info: IPRINT-lib Error Code: 4096 (0x1000) User ID: 1000 Error Msg: iPrint Lib - Bad URI type supplied (not IPP:, HTTP:, or HTTPS:). Debug Msg: IPRINTInterpretURI for hp:/usb/HP_LaserJet_1018?serial=KP103A1 - No Port type specified Thu Oct 31 11:02:08 2013 Trace Info: iprint.c, line 6690 Group Info: IPRINT-lib Error Code: 4096 (0x1000) User ID: 1000 Error Msg: iPrint Lib - Bad URI type supplied (not IPP:, HTTP:, or HTTPS:). Debug Msg: IPRINTInterpretURI for file:///dev/null - Unknown Port Type - file Thu Oct 31 11:02:08 2013 Trace Info: iprint.c, line 6800 Group Info: IPRINT-lib Error Code: 4096 (0x1000) User ID: 1000 Error Msg: iPrint Lib - Bad URI type supplied (not IPP:, HTTP:, or HTTPS:). Debug Msg: IPRINTInterpretURI for hp:/usb/HP_LaserJet_1018?serial=KP103A1 - No Port type specified I should say that my friend can print using the same instructions on CrunchBang easily and another guy on 12.04 LTS but with more struggling. It worked for me on linux mint maya with my old laptop as well. Is there anybody out there who can help me to solve these problems? I am really disappointed with Novell and our university support. PS. I had the same problemwith 13.04. No matter if I am within the network or I connect with VPN, I have the same issues.

    Read the article

  • How to Use Windows’ Advanced Search Features: Everything You Need to Know

    - by Chris Hoffman
    You should never have to hunt down a lost file on modern versions of Windows — just perform a quick search. You don’t even have to wait for a cartoon dog to find your files, like on Windows XP. The Windows search indexer is constantly running in the background to make quick local searches possible. This enables the kind of powerful search features you’d use on Google or Bing — but for your local files. Controlling the Indexer By default, the Windows search indexer watches everything under your user folder — that’s C:\Users\NAME. It reads all these files, creating an index of their names, contents, and other metadata. Whenever they change, it notices and updates its index. The index allows you to quickly find a file based on the data in the index. For example, if you want to find files that contain the word “beluga,” you can perform a search for “beluga” and you’ll get a very quick response as Windows looks up the word in its search index. If Windows didn’t use an index, you’d have to sit and wait as Windows opened every file on your hard drive, looked to see if the file contained the word “beluga,” and moved on. Most people shouldn’t have to modify this indexing behavior. However, if you store your important files in other folders — maybe you store your important data a separate partition or drive, such as at D:\Data — you may want to add these folders to your index. You can also choose which types of files you want to index, force Windows to rebuild the index entirely, pause the indexing process so it won’t use any system resources, or move the index to another location to save space on your system drive. To open the Indexing Options window, tap the Windows key on your keyboard, type “index”, and click the Indexing Options shortcut that appears. Use the Modify button to control the folders that Windows indexes or the Advanced button to control other options. To prevent Windows from indexing entirely, click the Modify button and uncheck all the included locations. You could also disable the search indexer entirely from the Programs and Features window. Searching for Files You can search for files right from your Start menu on Windows 7 or Start screen on Windows 8. Just tap the Windows key and perform a search. If you wanted to find files related to Windows, you could perform a search for “Windows.” Windows would show you files that are named Windows or contain the word Windows. From here, you can just click a file to open it. On Windows 7, files are mixed with other types of search results. On Windows 8 or 8.1, you can choose to search only for files. If you want to perform a search without leaving the desktop in Windows 8.1, press Windows Key + S to open a search sidebar. You can also initiate searches directly from Windows Explorer — that’s File Explorer on Windows 8. Just use the search box at the top-right of the window. Windows will search the location you’ve browsed to. For example, if you’re looking for a file related to Windows and know it’s somewhere in your Documents library, open the Documents library and search for Windows. Using Advanced Search Operators On Windows 7, you’ll notice that you can add “search filters” form the search box, allowing you to search by size, date modified, file type, authors, and other metadata. On Windows 8, these options are available from the Search Tools tab on the ribbon. These filters allow you to narrow your search results. If you’re a geek, you can use Windows’ Advanced Query Syntax to perform advanced searches from anywhere, including the Start menu or Start screen. Want to search for “windows,” but only bring up documents that don’t mention Microsoft? Search for “windows -microsoft”. Want to search for all pictures of penguins on your computer, whether they’re PNGs, JPEGs, or any other type of picture file? Search for “penguin kind:picture”. We’ve looked at Windows’ advanced search operators before, so check out our in-depth guide for more information. The Advanced Query Syntax gives you access to options that aren’t available in the graphical interface. Creating Saved Searches Windows allows you to take searches you’ve made and save them as a file. You can then quickly perform the search later by double-clicking the file. The file functions almost like a virtual folder that contains the files you specify. For example, let’s say you wanted to create a saved search that shows you all the new files created in your indexed folders within the last week. You could perform a search for “datecreated:this week”, then click the Save search button on the toolbar or ribbon. You’d have a new virtual folder you could quickly check to see your recent files. One of the best things about Windows search is that it’s available entirely from the keyboard. Just press the Windows key, start typing the name of the file or program you want to open, and press Enter to quickly open it. Windows 8 made this much more obnoxious with its non-unified search, but unified search is finally returning with Windows 8.1.     

    Read the article

  • Adding A Custom Dropdown in RCDC for Forefront Identity Manager 2010

    - by Daniel Lackey
    My latest exploration has been FIM 2010 for Identity Management. The following is a post of how to add a custom dropdown for the FIM Portal. I have decided to document this as I cannot find documentation on how to do this anywhere else. I hope that it finds useful to others.   For starters, this was to me not an easy task to figure out. I really would like to know why it is so cumbersome to do something that seems like a lot of people would need to do, but that’s for another day J   The dropdown I wanted to add was for ‘Account Status’ which would display if the account is ‘Enabled’ or ‘Disabled’ in the data source Active Directory. This option would also allow helpdesk users or admins to administer the userAccountControl attribute in AD from the FIM Portal interface.   The first thing I had to do was create the attribute itself. This is done by going to Administration à Schema Management from the FIM 2010 portal. Once here, you click on All Attributes. What is listed here are all attributes and their associated Resource Types in FIM. To create the ‘AccountStatus’ attribute, click on New. As shown below, enter ‘AccountStatus’ with no spaces for the System Name and ‘Account Status’ for the Display Name. The Data Type is going to be ‘Indexed String’. Click Next.           Leave everything on the Localization tab default and click Next.   On the Validation tab as shown below, we will enter the regex expression ^(Enabled|Disabled)?$ with our two desired string values ‘Enabled’ and ‘Disabled’. Click on Finish and then and Submit to complete adding the attribute.       The next step involves associating the attribute with a resource type. This is called ‘Binding’ the attribute. From the Schema Management page, click on All Bindings. From the page that comes up, click on New. As shown below, enter ‘User’ for the Resource Type and ‘Account Status’ for the Attribute Type. This is essentially binding the Account Status attribute to the ‘User’ Resource Type. Click Next.    On the ‘Attribute Override’ tab, type in ‘Account Status’ for the Display Name field. Click Next.   On the ‘Localization’ tab, click Next.   On the ‘Validation’ tab, enter the regex expression ^(Enabled|Disabled)?$ we entered previously for the attribute. Click Finish and then Submit to complete.   Now that the Attribute and the Binding are complete, you have to give users permission to see the attribute on the User Edit page. Go to Administration à Management Policy Rules. Look for the rule named Administration: Administrators can read and update Users and click on it. Once it opens, click on the ‘Target Resources’ tab and look at the section named Resource Attributes. Type in at the end the ‘Account Status’ attribute and check it with the validator. Once done click on OK to save the changes.         Lastly, we need to add the actual dropdown control to the RCDC (Resource Control Display Configuration) for User Editing. Go to Administration à Resource Control Display Configuration. From here navigate until you find the RCDC named Configuration for User Editing RCDC and click on it. The following is what you will see:       First step is to export the Configuration Data file. Click on the Export configuration link and save the file to your desktop of other folder.   Find the file you just exported and open the file in your XML editor of choice. I use notepad but anything will work. Since we are adding a dropdown control, first find another control in the existing file that is already a dropdown in FIM. I used EmployeeType as my example. Copy the control from the beginning tag named <my:Control… to the ending tag </my:Control>. Now take what you copied and paste it in whatever location you desire within the form between two other controls. I chose to place the ‘Account Status’ field after the ‘Account Name’ field. After you paste the control you will need to modify so it looks like this:       Notice where you specify what attribute you are dealing with where it has AccountStatus in the XML. Once you are complete with modifying this, save the file and make sure it is a .xml file.   Now go back to the Configuration for User Editing screen and look at the section named ‘Configuration Data’. Click the ‘Browse’ button and find the XML file you just modified and choose it. Click OK on the bottom of the window and you are done!   Now when you click on a user’s name in the FIM Portal, you should see the newly added dropdown box as below:       Later I will post more about this drop down, specifically on how to automate actually ‘Disabling’ the account in the data source through the FIM Workflows and MAs.   <my:Control my:Name="AccountStatus" my:TypeName="UocDropDownList" my:Caption="{Binding Source=schema, Path=AccountStatus.DisplayName}" my:Description="{Binding Source=schema, Path=AccountStatus.Description}" my:RightsLevel="{Binding Source=rights, Path=AccountStatus}"> <my:Properties> <my:Property my:Name="ValuePath" my:Value="Value"/> <my:Property my:Name="CaptionPath" my:Value="Caption"/> <my:Property my:Name="HintPath" my:Value="Hint"/> <my:Property my:Name="ItemSource" my:Value="{Binding Source=schema, Path=AccountStatus.LocalizedAllowedValues}"/> <my:Property my:Name="SelectedValue" my:Value="{Binding Source=object, Path=AccountStatus, Mode=TwoWay}"/> </my:Properties> </my:Control>

    Read the article

  • Ask How-To Geek: Learning the Office Ribbon, Booting to USB with an Old BIOS, and Snapping Windows

    - by Jason Fitzpatrick
    You’ve got questions and we’ve got answers. Today we highlight how to master the new Office interface, USB boot a computer with outdated BIOS, and snap windows to preset locations. Learning the New Office Ribbon Dear How-To Geek, I feel silly asking this (in light of how long the new Office interface has been out) but my company finally got around to upgrading from Windows XP and Office 2000 so the new interface it totally new to me. Can you recommend any resources for quickly learning the Office ribbon and the new changes? I feel completely lost after two decades of the old Office interface. Help! Sincerely, Where the Hell is Everything? Dear Where the Hell, We think most people were with you at some point in the last few years. “Where the hell is…” could possibly be the slogan for the new ribbon interface. You could browse through some of the dry tutorials online or even get a weighty book on the topic but the best way to learn something new is to get hands on. Ribbon Hero turns learning the new Office features and ribbon layout into a game. It’s no vigorous round of Team Fortress mind you, but it’s significantly more fun than reading a training document. Check out how to install and configure Ribbon Hero here. You’ll be teaching your coworkers new tricks in no time. Boot via USB with an Old BIOS Dear How-To Geek, I’m trying to repurpose some old computers by updating them with lightweight Linux distros but the BIOS on most of the machines is ancient and creaky. How ancient? It doesn’t even support booting from a USB device! I have a large flash drive that I’ve turned into a master installation tool for jobs like this but I can’t use it. The computers in question have USB ports; they just aren’t recognized during the boot process. What can I do? USB Bootin’ in Boise Dear USB Bootin’, It’s great you’re working to breathe life into old hardware! You’ve run into one of the limitations of older BIOSes, USB was around but nobody was thinking about booting off of it. Fortunately if you have a computer old enough to have that kind of BIOS it’s likely to also has a floppy drive or a CDROM drive. While you could make a bootable CDROM for your application we understand that you want to keep using the master USB installer you’ve made. In light of that we recommend PLoP Boot Manager. Think of it like a boot manager for your boot manager. Using it you can create a bootable floppy or CDROM that will enable USB booting of your master USB drive. Make a CD and a floppy version and you’ll have everything in your toolkit you need for future computer refurbishing projects. Read up on creating bootable media with PLoP Boot Manager here. Snapping Windows to Preset Coordinates Dear How-To Geek, Once upon a time I had a company laptop that came with a little utility that snapped windows to preset areas of the screen. This was long before the snap-to-side features in Windows 7. You could essentially configure your screen into a grid pattern of your choosing and then windows would neatly snap into those grids. I have no idea what it was called or if was anymore than a gimmick from the computer manufacturer, but I’d really like to have it on my new computer! Bend and Snap in San Francisco, Dear Bend and Snap, If we had to guess, we’d guess your company must have had a set of laptops from Acer as the program you’re describing sounds exactly like Acer GridVista. Fortunately for you the application was extremely popular and Acer released it independently of their hardware. If, by chance, you’ve since upgraded to a multiple monitor setup the app even supports multiple monitors—many of the configurations are handy for arranging IM windows and other auxiliary communication tools. Check out our guide to installing and configuring Acer GridVista here for more information. Have a question you want to put before the How-To Geek staff? Shoot us an email at [email protected] and then keep an eye out for a solution in the Ask How-To Geek column. Latest Features How-To Geek ETC How to Upgrade Windows 7 Easily (And Understand Whether You Should) The How-To Geek Guide to Audio Editing: Basic Noise Removal Install a Wii Game Loader for Easy Backups and Fast Load Times The Best of CES (Consumer Electronics Show) in 2011 The Worst of CES (Consumer Electronics Show) in 2011 HTG Projects: How to Create Your Own Custom Papercraft Toy Download the New Year in Japan Windows 7 Theme from Microsoft Once More Unto the Breach – Facebook Apps Can Now Access Your Address and Phone Number Dial Zero Speeds You Through Annoying Customer Service Menus Complete Dropquest 2011 and Receive Free Dropbox Storage Desktop Computer versus Laptop Wallpaper The Kids Have No Idea What Old Tech Is [Video]

    Read the article

  • Dec 5th Links: ASP.NET, ASP.NET MVC, jQuery, Silverlight, Visual Studio

    - by ScottGu
    Here is the latest in my link-listing series.  Also check out my VS 2010 and .NET 4 series for another on-going blog series I’m working on. [In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu] ASP.NET ASP.NET Code Samples Collection: J.D. Meier has a great post that provides a detailed round-up of ASP.NET code samples and tutorials from a wide variety of sources.  Lots of useful pointers. Slash your ASP.NET compile/load time without any hard work: Nice article that details a bunch of optimizations you can make to speed up ASP.NET project load and compile times. You might also want to read my previous blog post on this topic here. 10 Essential Tools for Building ASP.NET Websites: Great article by Stephen Walther on 10 great (and free) tools that enable you to more easily build great ASP.NET Websites.  Highly recommended reading. Optimize Images using the ASP.NET Sprite and Image Optimization Framework: A nice article by 4GuysFromRolla that discusses how to use the open-source ASP.NET Sprite and Image Optimization Framework (one of the tools recommended by Stephen in the previous article).  You can use this to significantly improve the load-time of your pages on the client. Formatting Dates, Times and Numbers in ASP.NET: Scott Mitchell has a great article that discusses formatting dates, times and numbers in ASP.NET.  A very useful link to bookmark.  Also check out James Michael’s DateTime is Packed with Goodies blog post for other DateTime tips. Examining ASP.NET’s Membership, Roles and Profile APIs (Part 18): Everything you could possibly want to known about ASP.NET’s built-in Membership, Roles and Profile APIs must surely be in this tutorial series. Part 18 covers how to store additional user info with Membership. ASP.NET with jQuery An Introduction to jQuery Templates: Stephen Walther has written an outstanding introduction and tutorial on the new jQuery Template plugin that the ASP.NET team has contributed to the jQuery project. Composition with jQuery Templates and jQuery Templates, Composite Rendering, and Remote Loading: Dave Ward has written two nice posts that talk about composition scenarios with jQuery Templates and some cool scenarios you can enable with them. Using jQuery and ASP.NET to Build a News Ticker: Scott Mitchell has a nice tutorial that demonstrates how to build a dynamically updated “news ticker” style UI with ASP.NET and jQuery. Checking All Checkboxes in a GridView using jQuery: Scott Mitchell has a nice post that covers how to use jQuery to enable a checkbox within a GridView’s header to automatically check/uncheck all checkboxes contained within rows of it. Using jQuery to POST Form Data to an ASP.NET AJAX Web Service: Rick Strahl has a nice post that discusses how to capture form variables and post them to an ASP.NET AJAX Web Service (.asmx). ASP.NET MVC ASP.NET MVC Diagnostics Using NuGet: Phil Haack has a nice post that demonstrates how to easily install a diagnostics page (using NuGet) that can help identify and diagnose common configuration issues within your apps. ASP.NET MVC 3 JsonValueProviderFactory: James Hughes has a nice post that discusses how to take advantage of the new JsonValueProviderFactory support built into ASP.NET MVC 3.  This makes it easy to post JSON payloads to MVC action methods. Practical jQuery Mobile with ASP.NET MVC: James Hughes has another nice post that discusses how to use the new jQuery Mobile library with ASP.NET MVC to build great mobile web applications. Credit Card Validator for ASP.NET MVC 3: Benjii Me has a nice post that demonstrates how to build a [CreditCard] validator attribute that can be used to easily validate credit card numbers are in the correct format with ASP.NET MVC. Silverlight Silverlight FireStarter Keynote and Sessions: A great blog post from John Papa that contains pointers and descriptions of all the great Silverlight content we published last week at the Silverlight FireStarter.  You can watch all of the talks online.  More details on my keynote and Silverlight 5 announcements can be found here. 31 Days of Windows Phone 7: 31 great tutorials on how to build Windows Phone 7 applications (using Silverlight).  Silverlight for Windows Phone Toolkit Update: David Anson has a nice post that discusses some of the additional controls provided with the Silverlight for Windows Phone Toolkit. Visual Studio JavaScript Editor Extensions: A nice (and free) Visual Studio plugin built by the web tools team that significantly improves the JavaScript intellisense support within Visual Studio. HTML5 Intellisense for Visual Studio: Gil has a blog post that discusses a new extension my team has posted to the Visual Studio Extension Gallery that adds HTML5 schema support to Visual Studio 2008 and 2010. Team Build + Web Deployment + Web Deploy + VS 2010 = Goodness: Visual blogs about how to enable a continuous deployment system with VS 2010, TFS 2010 and the Microsoft Web Deploy framework.  Visual Studio 2010 Emacs Emulation Extension and VIM Emulation Extension: Check out these two extensions if you are fond of Emacs and VIM key bindings and want to enable them within Visual Studio 2010. Hope this helps, Scott

    Read the article

  • mysql not starting

    - by Eiriks
    I have a server running on rackspace.com, it been running for about a year (collecting data for a project) and no problems. Now it seems mysql froze (could not connect either through ssh command line, remote app (sequel pro) or web (pages using the db just froze). I got a bit eager to fix this quick and rebooted the virtual server, running ubuntu 10.10. It is a small virtual LAMP server (10gig storage - I'm only using 1, 256mb ram -has not been a problem). Now after the reboot, I cannot get mysql to start again. service mysql status mysql stop/waiting I believe this just means mysql is not running. How do I get this running again? service mysql start start: Job failed to start No. Just typing 'mysql' gives: mysql ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (111) There is a .sock file in this folder, 'ls -l' gives: srwxrwxrwx 1 mysql mysql 0 2012-12-01 17:20 mysqld.sock From googleing this for a while now, I see that many talk about the logfile and my.cnf. Logs Not sure witch ones I should look at. This log-file is empty: 'var/log/mysql/error.log', so is the 'var/log/mysql.err' and 'var/log/mysql.log'. my.cnf is located in '/etc/mysql' and looks like this. Can't see anything clearly wrong with it either. # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 16M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 log_error = /var/log/mysql/error.log # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ I need the data in the database (so i'd like to avoid reinstalling), and I need it back up running again. All hint, tips and solutions are welcomed and appreciated.

    Read the article

  • The Challenge with HTML5 – In Pictures

    - by dwahlin
    I love working with Web technologies and am looking forward to the new functionality that HTML5 will ultimately bring to the table (some of which can be used today). Having been through the div versus layer battle back in the IE4 and Netscape 4 days I think we’re headed down that road again as a result of browsers implementing features differently. I’ve been spending a lot of time researching and playing around with HTML5 samples and features (mainly because we’re already seeing demand for training on HTML5) and there’s a lot of great stuff there that will truly revolutionize web applications as we know them. However, browsers just aren’t there yet and many people outside of the development world don’t really feel a need to upgrade their browser if it’s working reasonably well (Mom and Dad come to mind) so it’s going to be awhile. There’s a nice test site at http://www.HTML5Test.com that runs through different HTML5 features and scores how well they’re supported. They don’t test for everything and are very clear about that on the site: “The HTML5 test score is only an indication of how well your browser supports the upcoming HTML5 standard and related specifications. It does not try to test all of the new features offered by HTML5, nor does it try to test the functionality of each feature it does detect. Despite these shortcomings we hope that by quantifying the level of support users and web developers will get an idea of how hard the browser manufacturers work on improving their browsers and the web as a development platform. The score is calculated by testing for the many new features of HTML5. Each feature is worth one or more points. Apart from the main HTML5 specification and other specifications created the W3C HTML Working Group, this test also awards points for supporting related drafts and specifications. Some of these specifications were initially part of HTML5, but are now further developed by other W3C working groups. WebGL is also part of this test despite not being developed by the W3C, because it extends the HTML5 canvas element with a 3d context. The test also awards bonus points for supporting audio and video codecs and supporting SVG or MathML embedding in a plain HTML document. These test do not count towards the total score because HTML5 does not specify any required audio or video codec. Also SVG and MathML are not required by HTML5, the specification only specifies rules for how such content should be embedded inside a plain HTML file. Please be aware that the specifications that are being tested are still in development and could change before receiving an official status. In the future new tests will be added for the pieces of the specification that are currently still missing. The maximum number of points that can be scored is 300 at this moment, but this is a moving goalpost.” It looks like their tests haven’t been updated since June, but the numbers are pretty scary as a developer because it means I’m going to have to do a lot of browser sniffing before assuming a particular feature is available to use. Not that much different from what we do today as far as browser sniffing you say? I’d have to disagree since HTML5 takes it to a whole new level. In today’s world we have script libraries such as jQuery (my personal favorite), Prototype, script.aculo.us, YUI Library, MooTools, etc. that handle the heavy lifting for us. Until those libraries handle all of the key HTML5 features available it’s going to be a challenge. Certain features such as Canvas are supported fairly well across most of the major browsers while other features such as audio and video are hit or miss depending upon what codec you want to use. Run the tests yourself to see what passes and what fails for different browsers. You can also view the HTML5 Test Suite Conformance Results at http://test.w3.org/html/tests/reporting/report.htm (a work in progress). The table below lists the scores that the HTML5Test site returned for different browsers I have installed on my desktop PC and laptop. A specific list of tests run and features supported are given when you go to the site. Note that I went ahead and tested the IE9 beta and it didn’t do nearly as good as I expected it would, but it’s not officially out yet so I expect that number will change a lot. Am I opposed to HTML5 as a result of these tests? Of course not - I’m actually really excited about what it offers.  However, I’m trying to be realistic and feel it'll definitely add a new level of headache to the Web application development process having been through something like this many years ago. On the flipside, developers that are able to target a specific browser (typically Intranet apps) or master the cross-browser issues are going to release some pretty sweet applications. Check out http://html5gallery.com/ for a look at some of the more cutting-edge sites out there that use HTML5. Also check out the http://www.beautyoftheweb.com site that Microsoft put together to showcase IE9. Chrome 8 Safari 5 for Windows     Opera 10 Firefox 3.6     Internet Explorer 9 Beta (Note that it’s still beta) Internet Explorer 8

    Read the article

  • Oracle Open World 2012: SQL Developer Recap

    - by thatjeffsmith
    Last week was the ‘big show’ in San Francisco. I was very happy to meet many of you in person. And many of you had questions – lots of questions! We had full or overflowing rooms for our sessions and hands-on-labs. The SQL Developer ‘booths’ were also slammed several times. So exciting to see so many of YOU excited about SQL Developer. It’s very cool to hear the stories of our tools saving you and your organizations so much time (and money!) Instead of doing a Day 0 – Day 9 recap, I thought I’d share with you the questions that I heard more than once. And just for giggles, I’ll throw in some answers as well So in no particular order… What’s the difference between Oracle SQL Developer & Oracle SQL Developer Data Modeler? Mathematically speaking – two words. But as far as the actual modeling features go, there’s no difference between the two applications. The same ‘code’ or features as it pertains to data modeling and design are in both tools. However, in SQL Developer you have all of the OTHER features fighting for real estate in the UI. So I have a general rule of thumb – if you spend MOST of your time in the database, use SQL Developer. And if you spend most of your time in the data model, run the separate and dedicated program, Oracle SQL Developer Data Modeler. Here’s a couple of screenshots to drive home the UI point: Oracle SQL Developer Oracle SQL Developer Data Modeler running INSIDE of SQL Developer. Notice how the Modeler menu items fold under the file menu? Oracle SQL Developer Data Modeler Easier to navigate and manipulate your models with the stand alone modeler. Just no worksheet to run your ad-hoc queries, etc. Don’t forget you can disable the Data Modeler inside of SQL Developer via the Extensions preference page. How can I model my table partitions? Partitioning is defined via the Physical model. So after you have finished your relational model, you need to generate a physical model. Oracle SQL Developer Data Modeler Physical Model and Partitioning Open the properties for your physical model table. Enable the ‘partitioned’ property. Once you do so, the ‘Partitioning’ page will activate. Lots and lots of partitioning support and options here But what about Interval Partitioning? An extension of range partitioning in 11gR2, we don’t currently support this partitioning scheme in SQL Developer. But we’re working on it! Can SQL Developer ignore column order when comparing models? Yes! After you start a model compare, one of your options is to disregard the order of an attribute or column definition. Tell SQL Developer you don’t care when your column shows up, just as long as it DOES show up. Wow, you got a lot of questions around modeling! Is that normal? Yes! While we appreciate that many folks inherit their applications and associated designs, new applications are being ‘born’ every day. Since both of our tools are free for anyone to design their new Oracle applications with, we attract a fair amount of attention I want to do a Hands On Lab. How do I get your software and instructional guides? Go here. Download VirtualBox. Then download the VB image. Import the appliance. Start it. Connect oracle/oracle on the OEL VM. Click on ‘Start Here’ in the desktop. Follow the instructions. If you need help, ask away! You went too fast in your Tips & Tricks session. Do you have cliff notes? Yes! And you’re SO close to finding them! Just go to my SQL Developer resources page. All of my tips are documented on this blog somewhere. I’ve indexed the most popular ones on the resource page. You can use the Search dialog on the right to find the rest. Or just send me a comment or question, and I’ll do my best to answer them as they come in.

    Read the article

  • WebLogic Server Performance and Tuning: Part I - Tuning JVM

    - by Gokhan Gungor
    Each WebLogic Server instance runs in its own dedicated Java Virtual Machine (JVM) which is their runtime environment. Every Admin Server in any domain executes within a JVM. The same also applies for Managed Servers. WebLogic Server can be used for a wide variety of applications and services which uses the same runtime environment and resources. Oracle WebLogic ships with 2 different JVM, HotSpot and JRocket but you can choose which JVM you want to use. JVM is designed to optimize itself however it also provides some startup options to make small changes. There are default values for its memory and garbage collection. In real world, you will not want to stick with the default values provided by the JVM rather want to customize these values based on your applications which can produce large gains in performance by making small changes with the JVM parameters. We can tell the garbage collector how to delete garbage and we can also tell JVM how much space to allocate for each generation (of java Objects) or for heap. Remember during the garbage collection no other process is executed within the JVM or runtime, which is called STOP THE WORLD which can affect the overall throughput. Each JVM has its own memory segment called Heap Memory which is the storage for java Objects. These objects can be grouped based on their age like young generation (recently created objects) or old generation (surviving objects that have lived to some extent), etc. A java object is considered garbage when it can no longer be reached from anywhere in the running program. Each generation has its own memory segment within the heap. When this segment gets full, garbage collector deletes all the objects that are marked as garbage to create space. When the old generation space gets full, the JVM performs a major collection to remove the unused objects and reclaim their space. A major garbage collect takes a significant amount of time and can affect system performance. When we create a managed server either on the same machine or on remote machine it gets its initial startup parameters from $DOMAIN_HOME/bin/setDomainEnv.sh/cmd file. By default two parameters are set:     Xms: The initial heapsize     Xmx: The max heapsize Try to set equal initial and max heapsize. The startup time can be a little longer but for long running applications it will provide a better performance. When we set -Xms512m -Xmx1024m, the physical heap size will be 512m. This means that there are pages of memory (in the state of the 512m) that the JVM does not explicitly control. It will be controlled by OS which could be reserve for the other tasks. In this case, it is an advantage if the JVM claims the entire memory at once and try not to spend time to extend when more memory is needed. Also you can use -XX:MaxPermSize (Maximum size of the permanent generation) option for Sun JVM. You should adjust the size accordingly if your application dynamically load and unload a lot of classes in order to optimize the performance. You can set the JVM options/heap size from the following places:     Through the Admin console, in the Server start tab     In the startManagedWeblogic script for the managed servers     $DOMAIN_HOME/bin/startManagedWebLogic.sh/cmd     JAVA_OPTIONS="-Xms1024m -Xmx1024m" ${JAVA_OPTIONS}     In the setDomainEnv script for the managed servers and admin server (domain wide)     USER_MEM_ARGS="-Xms1024m -Xmx1024m" When there is free memory available in the heap but it is too fragmented and not contiguously located to store the object or when there is actually insufficient memory we can get java.lang.OutOfMemoryError. We should create Thread Dump and analyze if that is possible in case of such error. The second option we can use to produce higher throughput is to garbage collection. We can roughly divide GC algorithms into 2 categories: parallel and concurrent. Parallel GC stops the execution of all the application and performs the full GC, this generally provides better throughput but also high latency using all the CPU resources during GC. Concurrent GC on the other hand, produces low latency but also low throughput since it performs GC while application executes. The JRockit JVM provides some useful command-line parameters that to control of its GC scheme like -XgcPrio command-line parameter which takes the following options; XgcPrio:pausetime (To minimize latency, parallel GC) XgcPrio:throughput (To minimize throughput, concurrent GC ) XgcPrio:deterministic (To guarantee maximum pause time, for real time systems) Sun JVM has similar parameters (like  -XX:UseParallelGC or -XX:+UseConcMarkSweepGC) to control its GC scheme. We can add -verbosegc -XX:+PrintGCDetails to monitor indications of a problem with garbage collection. Try configuring JVM’s of all managed servers to execute in -server mode to ensure that it is optimized for a server-side production environment.

    Read the article

  • nvidia driver problem after update

    - by baltasar
    I know there are a lot of posts about nvdia driver, but I am not able to solve this. I updated my configuration yesterday, September 27th, and it seems that a new nvidia driver was involved. The updated completed with an error, and invited me to send a bug report automatically. I send it, but it finally said that there was no place to send the bug report to. Today I updated again, and a new kernel was there. Then I rebooted. I found a desktop in 640x480 with a horrible, unreadable font. I run jockey and tried to go back to another version of the nvidia driver, but it seems that none of the drivers listed there are suddenly valid. I have the x-swat repository enabled, because I remember that I had a similar issue in the past that was only to be solved with the newest driver. jockey log: 2012-09-28 11:22:24,747 DEBUG: Selecting previously unselected package nvidia-173. (Reading database ... 536311 files and directories currently installed.) Unpacking nvidia-173 (from .../nvidia-173_173.14.35-0ubuntu0.2_i386.deb) ... Processing triggers for man-db ... Setting up nvidia-173 (173.14.35-0ubuntu0.2) ... Loading new nvidia-173-173.14.35 DKMS files... Building only for 3.2.0-32-generic-pae Building for architecture i686 Building initial module for 3.2.0-32-generic-pae Error! Bad return status for module build on kernel: 3.2.0-32-generic-pae (i686) Consult /var/lib/dkms/nvidia-173/173.14.35/build/make.log for more information. Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... 2012-09-28 11:22:25,143 WARNING: modinfo for module nvidia_173 failed: ERROR: modinfo: could not find module nvidia_173 2012-09-28 11:22:25,143 ERROR: XorgDriverHandler.enable(): package or module not installed, aborting 2012-09-28 11:22:53,613 DEBUG: NVidia(nvidia_173).enabled(): target_alt /usr/lib/nvidia-173/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-173/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:22:53,613 DEBUG: KMH enabled: False 2012-09-28 11:22:53,629 DEBUG: NVidia(nvidia_173).enabled(): target_alt /usr/lib/nvidia-173/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-173/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:22:53,629 DEBUG: KMH enabled: False 2012-09-28 11:23:01,943 DEBUG: NVidia(nvidia_173).enabled(): target_alt /usr/lib/nvidia-173/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-173/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:01,943 DEBUG: KMH enabled: False 2012-09-28 11:23:01,962 DEBUG: NVidia(nvidia_173).enabled(): target_alt /usr/lib/nvidia-173/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-173/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:01,963 DEBUG: KMH enabled: False 2012-09-28 11:23:01,998 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-173/ld.so.conf other target alt None other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:01,998 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-28 11:23:02,044 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,044 DEBUG: nvidia_current is not the alternative in use 2012-09-28 11:23:02,066 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,066 DEBUG: nvidia_current is not the alternative in use 2012-09-28 11:23:02,106 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-173/ld.so.conf other target alt None other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,106 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-28 11:23:02,157 DEBUG: NVidia(nvidia_173).enabled(): target_alt /usr/lib/nvidia-173/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-173/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,157 DEBUG: KMH enabled: False 2012-09-28 11:23:02,177 DEBUG: NVidia(nvidia_173).enabled(): target_alt /usr/lib/nvidia-173/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-173/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,178 DEBUG: KMH enabled: False 2012-09-28 11:23:02,245 DEBUG: NVidia(nvidia_173).enabled(): target_alt /usr/lib/nvidia-173/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-173/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,245 DEBUG: KMH enabled: False 2012-09-28 11:23:02,272 DEBUG: NVidia(nvidia_173).enabled(): target_alt /usr/lib/nvidia-173/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-173/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,273 DEBUG: KMH enabled: False 2012-09-28 11:23:02,303 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-173/ld.so.conf other target alt None other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,303 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-28 11:23:02,330 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,410 DEBUG: nvidia_current is not the alternative in use 2012-09-28 11:23:02,427 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-173/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,428 DEBUG: nvidia_current is not the alternative in use 2012-09-28 11:23:02,457 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-173/ld.so.conf other target alt None other current alt /usr/lib/nvidia-173/alt_ld.so.conf 2012-09-28 11:23:02,458 DEBUG: nvidia_current_updates is not the alternative in use

    Read the article

  • How to Use An Antivirus Boot Disc or USB Drive to Ensure Your Computer is Clean

    - by Chris Hoffman
    If your computer is infected with malware, running an antivirus within Windows may not be enough to remove it. If your computer has a rootkit, the malware may be able to hide itself from your antivirus software. This is where bootable antivirus solutions come in. They can clean malware from outside the infected Windows system, so the malware won’t be running and interfering with the clean-up process. The Problem With Cleaning Up Malware From Within Windows Standard antivirus software runs within Windows. If your computer is infected with malware, the antivirus software will have to do battle with the malware. Antivirus software will try to stop the malware and remove it, while the malware will attempt to defend itself and shut down the antivirus. For really nasty malware, your antivirus software may not be able to fully remove it from within Windows. Rootkits, a type of malware that hides itself, can be even trickier. A rootkit could load at boot time before other Windows components and prevent Windows from seeing it, hide its processes from the task manager, and even trick antivirus applications into believing that the rootkit isn’t running. The problem here is that the malware and antivirus are both running on the computer at the same time. The antivirus is attempting to fight the malware on its home turf — the malware can put up a fight. Why You Should Use an Antivirus Boot Disc Antivirus boot discs deal with this by approaching the malware from outside Windows. You boot your computer from a CD or USB drive containing the antivirus and it loads a specialized operating system from the disc. Even if your Windows installation is completely infected with malware, the special operating system won’t have any malware running within it. This means the antivirus program can work on the Windows installation from outside it. The malware won’t be running while the antivirus tries to remove it, so the antivirus can methodically locate and remove the harmful software without it interfering. Any rootkits won’t be able to set up the tricks they use at Windows boot time to hide themselves from the rest o the operating system. The antivirus will be able to see the rootkits and remove them. These tools are often referred to as “rescue disks.” They’re meant to be used when you need to rescue a hopelessly infected system. Bootable Antivirus Options As with any type of antivirus software, you have quite a few options. Many antivirus companies offer bootable antivirus systems based on their antivirus software. These tools are generally free, even when they’re offered by companies that specialized in paid antivirus solutions. Here are a few good options: avast! Rescue Disk – We like avast! for offering a capable free antivirus with good detection rates in independent tests. avast! now offers the ability to create an antivirus boot disc or USB drive. Just navigate to the Tools -> Rescue Disk option in the avast! desktop application to create bootable media. BitDefender Rescue CD – BitDefender always seems to receive good scores in independent tests, and the BitDefender Rescue CD offers the same antivirus engine in the form of a bootable disc. Kaspersky Rescue Disk – Kaspersky also receives good scores in independent tests and offers its own antivirus boot disc. These are just a handful of options. If you prefer another antivirus for some reason — Comodo, Norton, Avira, ESET, or almost any other antivirus product — you’ll probably find that it offers its own system rescue disk. How to Use an Antivirus Boot Disc Using an antivirus boot disc or USB drive is actually pretty simple. You’ll just need to find the antivirus boot disc you want to use and burn it to disc or install it on a USB drive. You can do this part on any computer, so you can create antivirus boot media on a clean computer and then take it to an infected computer. Insert the boot media into the infected computer and then reboot. The computer should boot from the removable media and load the secure antivirus environment. (If it doesn’t, you may need to change the boot order in your BIOS or UEFI firmware.) You can then follow the instructions on your screen to scan your Windows system for malware and remove it. No malware will be running in the background while you do this. Antivirus boot discs are useful because they allow you to detect and clean malware infections from outside an infected operating system. If the operating system is severely infected, it may not be possible to remove — or even detect — all the malware from within it. Image Credit: aussiegall on Flickr     

    Read the article

  • Using CMS for App Configuration - Part 1, Deploying Umbraco

    - by Elton Stoneman
    Originally posted on: http://geekswithblogs.net/EltonStoneman/archive/2014/06/04/using-cms-for-app-configurationndashpart-1-deploy-umbraco.aspxSince my last post on using CMS for semi-static API content, How about a new platform for your next API… a CMS?, I’ve been using the idea for centralized app configuration, and this post is the first in a series that will walk through how to do that, step-by-step. The approach gives you a platform-independent, easily configurable way to specify your application configuration for different environments, with a built-in approval workflow, change auditing and the ability to easily rollback to previous settings. It’s like Azure Web and Worker Roles where you can specify settings that change at runtime, but it's not specific to Azure - you can use it for any app that needs changeable config, provided it can access the Internet. The series breaks down into four posts: Deploying Umbraco – the CMS that will store your configurable settings and the current values; Publishing your config – create a document type that encapsulates your settings and a template to expose them as JSON; Consuming your config – in .NET, a simple client that uses dynamic objects to access settings; Config lifecycle management – how to publish, audit, and rollback settings. Let’s get started. Deploying Umbraco There’s an Umbraco package on Azure Websites, so deploying your own instance is easy – but there are a couple of things to watch out for, so this step-by-step will put you in a good place. Create From Gallery The easiest way to get started is with an Azure subscription, navigate to add a new Website and then Create From Gallery. Under CMS, you’ll see an Umbraco package (currently at version 7.1.3): Configure Your App For high availability and scale, you’ll want your CMS on separate kit from anything else you have in Azure, so in the configuration of Umbraco I’d create a new SQL Azure database – which Umbraco will use to store all its content: You can use the free 20mb database option if you don’t have demanding NFRs, or if you’re just experimenting. You’ll need to specify a password for a SQL Server account which the Umbraco service will use, and changing from the default username umbracouser is probably wise. Specify Database Settings You can create a new database on an existing server if you have one, or create new. If you create a new server *do not* use the same username for the database server login as you used for the Umbraco account. If you do, the deployment will fail later. Think of this as the SQL Admin account that you can use for managing the db, the previous account was the service account Umbraco uses to connect. Make Tea If you have a fast kettle. It takes about two minutes for Azure to create and provision the website and the database. Install Umbraco So far we’ve deployed an empty instance of Umbraco using the Azure package, and now we need to browse to the site and complete installation. My Website was called my-app-config, so to complete installation I browse to http://my-app-config.azurewebsites.net:   Enter the credentials you want to use to login – this account will have full admin rights to the Umbraco instance. Note that between deploying your new Umbraco instance and completing installation in this step, anyone can browse to your website and complete the installation themselves with their own credentials, if they know the URL. Remote possibility, but it’s there. From this page *do not* click the big green Install button. If you do, Umbraco will configure itself with a local SQL Server CE database (.sdf file on the Web server), and ignore the SQL Azure database you’ve carefully provisioned and may be paying for. Instead, click on the Customize link and: Configure Your Database You need to enter your SQL Azure database details here, so you’ll have to get the server name from the Azure Management Console. You don’t need to explicitly grant access to your Umbraco website for the database though. Click Continue and you’ll be offered a “starter” website to install: If you don’t know Umbraco at all (but you are familiar with ASP.NET MVC) then a starter website is worthwhile to see how it all hangs together. But after a while you’ll have a bunch of artifacts in your CMS that you don’t want and you’ll have to work out which you can safely delete. So I’d click “No thanks, I do not want to install a starter website” and give yourself a clean Umbraco install. When it completes, the installation will log you in to the welcome screen for managing Umbraco – which you can access from http://my-app-config.azurewebsites.net/umbraco: That’s It Easy. Umbraco is installed, using a dedicated SQL Azure instance that you can separately scale, sync and backup, and ready for your content. In the next post, we’ll define what our app config looks like, and publish some settings for the dev environment.

    Read the article

  • Can't install wine (or ia32-libs) in Ubuntu 12.10 64 bit

    - by carestad
    As already pointed out here, people seems to have issues with installing wine in the latest version of Ubuntu. I'm suspecting this only happens with 64 bit users. For example, when trying to install wine, wine1.4, wine1.4:i386, wine1.5, wine1.5:i386, ia32-libs or ia32-libs:i386 with apt-get, I get a lot of dependency errors. Doing a sudo apt-get -f install doesn't seem to do the trick, neither does using aptitude. The errors I get is normally that the packages depend on some :i386 package, but installing those manually doesn't work either because they also have dependency issues (isn't APT supposed to do this automatically?!). I also downloaded CrossOver today and tried installing the .deb manually, but the dependency issues show up there as well. When running sudo apt-get -f install after trying to install the CrossOver .deb, apt-get wants to purge the following packages: ia32-crossover intel-gpu-tools libdrm-nouveau2 libgl1-mesa-dri libva-x11-1 ubuntu-desktop vlc xorg xserver-xorg-video-ati xserver-xorg-video-intel xserver-xorg-video-modesetting xserver-xorg-video-openchrome xserver-xorg-video-radeon xserver-xorg-video-vmware What I've tried so far (and didn't work): Installing synaptic, reloading my repositories, searching for ia32 and installing ia32-libs. Using Ubuntu Software Center to install Wine and ia32-libs. Using apt-get and aptitude to install all the differend varieties of the wine packages, both with and without the :i386 and -amd64 suffixes in package names. Disabling the universe and multiverse repos, run a sudo apt-get update and then re-enable them again. Boot a newly downloaded Ubuntu 12.10 x64 live USB and try to install all the different packages there. What I haven't tried (yet): Boot a newly downloaded Ubuntu 12.10 x32 image and try to install wine there (I'm just guessing that will work). Reinstall Ubuntu. Throw my computer out a window. wine alexander@cosmo:~$ LANGUAGE=en_US sudo apt-get install wine Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: wine : Depends: wine1.5 but it is not going to be installed E: Unable to correct problems, you have held broken packages. wine-1.4 alexander@cosmo:~$ LANGUAGE=en_US sudo apt-get install wine1.4 (...) The following packages have unmet dependencies: wine1.4 : Depends: wine1.4-i386 (= 1.4.1-0ubuntu1) E: Unable to correct problems, you have held broken packages. wine-1.4:i386 alexander@cosmo:~$ LANGUAGE=en_US sudo apt-get install wine1.4:i386 (...) The following packages have unmet dependencies: libaudio2:i386 : Depends: libxt6:i386 but it is not going to be installed libqtgui4:i386 : Depends: libsm6:i386 but it is not going to be installed libunity-webapps0 : Depends: unity-webapps-service but it is not going to be installed openssh-client : Depends: adduser (>= 3.10) but it is not going to be installed Depends: passwd ssh : Depends: openssh-server wine1.4:i386 : Depends: wine1.4-i386:i386 (= 1.4.1-0ubuntu1) Depends: binfmt-support:i386 (>= 1.1.2) Depends: procps:i386 Recommends: cups-bsd:i386 Recommends: gnome-exe-thumbnailer:i386 but it is not installable or kde-runtime:i386 but it is not going to be installed Recommends: ttf-droid:i386 but it is not installable Recommends: ttf-liberation:i386 but it is not installable Recommends: ttf-mscorefonts-installer:i386 Recommends: ttf-umefont:i386 but it is not installable Recommends: ttf-unfonts-core:i386 but it is not installable Recommends: ttf-wqy-microhei:i386 but it is not installable Recommends: winbind:i386 Recommends: winetricks:i386 but it is not going to be installed Recommends: xdg-utils:i386 but it is not installable E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. wine-1.5 alexander@cosmo:~$ sudo apt-get install wine1.5 (...) The following packages have unmet dependencies: wine1.5 : Depends: wine1.5-i386 (= 1.5.16-0ubuntu1) E: Unable to correct problems, you have held broken packages. wine-1.5:i386 alexander@cosmo:~$ sudo apt-get install wine1.5:i386 (...) The following packages have unmet dependencies: libaudio2:i386 : Depends: libxt6:i386 but it is not going to be installed libqtgui4:i386 : Depends: libsm6:i386 but it is not going to be installed libunity-webapps0 : Depends: unity-webapps-service but it is not going to be installed openssh-client : Depends: adduser (>= 3.10) but it is not going to be installed Depends: passwd ssh : Depends: openssh-server wine1.5:i386 : Depends: wine1.5-i386:i386 (= 1.5.16-0ubuntu1) but it is not going to be installed Depends: binfmt-support:i386 (>= 1.1.2) Depends: procps:i386 Recommends: cups-bsd:i386 Recommends: gnome-exe-thumbnailer:i386 but it is not installable or kde-runtime:i386 but it is not going to be installed Recommends: ttf-droid:i386 but it is not installable Recommends: ttf-liberation:i386 but it is not installable Recommends: ttf-mscorefonts-installer:i386 Recommends: ttf-umefont:i386 but it is not installable Recommends: ttf-unfonts-core:i386 but it is not installable Recommends: ttf-wqy-microhei:i386 but it is not installable Recommends: winbind:i386 Recommends: winetricks:i386 but it is not going to be installed Recommends: xdg-utils:i386 but it is not installable E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. ia32-libs alexander@cosmo:~$ sudo apt-get install ia32-libs (...) The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-multiarch E: Unable to correct problems, you have held broken packages. ia32-libs:i386 alexander@cosmo:~$ sudo apt-get install ia32-libs:i386 (...) Package ia32-libs:i386 is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source However the following packages replace it: lib32z1 lib32ncurses5 lib32bz2-1.0 lib32asound2 E: Package 'ia32-libs:i386' has no installation candidate

    Read the article

  • Clean up after Visual Studio

    - by psheriff
    As programmer’s we know that if we create a temporary file during the running of our application we need to make sure it is removed when the application or process is complete. We do this, but why can’t Microsoft do it? Visual Studio leaves tons of temporary files all over your hard drive. This is why, over time, your computer loses hard disk space. This blog post will show you some of the most common places where these files are left and which ones you can safely delete..NET Left OversVisual Studio is a great development environment for creating applications quickly. However, it will leave a lot of miscellaneous files all over your hard drive. There are a few locations on your hard drive that you should be checking to see if there are left-over folders or files that you can delete. I have attempted to gather as much data as I can about the various versions of .NET and operating systems. Of course, your mileage may vary on the folders and files I list here. In fact, this problem is so prevalent that PDSA has created a Computer Cleaner specifically for the Visual Studio developer.  Instructions for downloading our PDSA Developer Utilities (of which Computer Cleaner is one) are at the end of this blog entry.Each version of Visual Studio will create “temporary” files in different folders. The problem is that the files created are not always “temporary”. Most of the time these files do not get cleaned up like they should. Let’s look at some of the folders that you should periodically review and delete files within these folders.Temporary ASP.NET FilesAs you create and run ASP.NET applications from Visual Studio temporary files are placed into the <sysdrive>:\Windows\Microsoft.NET\Framework[64]\<vernum>\Temporary ASP.NET Files folder. The folders and files under this folder can be removed with no harm to your development computer. Do not remove the "Temporary ASP.NET Files" folder itself, just the folders underneath this folder. If you use IIS for ASP.NET development, you may need to run the iisreset.exe utility from the command prompt prior to deleting any files/folder under this folder. IIS will sometimes keep files in use in this folder and iisreset will release the locks so the files/folders can be deleted.Website CacheThis folder is similar to the ASP.NET Temporary Files folder in that it contains files from ASP.NET applications run from Visual Studio. This folder is located in each users local settings folder. The location will be a little different on each operating system. For example on Windows Vista/Windows 7, the folder is located at <sysdrive>:\Users\<UserName>\AppData\Local\Microsoft\WebsiteCache. If you are running Windows XP this folder is located at <sysdrive>:\ Documents and Settings\<UserName>\Local Settings\Application Data\Microsoft\WebsiteCache. Check these locations periodically and delete all files and folders under this directory.Visual Studio BackupThis backup folder is used by Visual Studio to store temporary files while you develop in Visual Studio. This folder never gets cleaned out, so you should periodically delete all files and folders under this directory. On Windows XP, this folder is located at <sysdrive>:\Documents and Settings\<UserName>\My Documents\Visual Studio 200[5|8]\Backup Files. On Windows Vista/Windows 7 this folder is located at <sysdrive>:\Users\<UserName>\Documents\Visual Studio 200[5|8]\.Assembly CacheNo, this is not the global assembly cache (GAC). It appears that this cache is only created when doing WPF or Silverlight development with Visual Studio 2008 or Visual Studio 2010. This folder is located in <sysdrive>:\ Users\<UserName>\AppData\Local\assembly\dl3 on Windows Vista/Windows 7. On Windows XP this folder is located at <sysdrive>:\ Documents and Settings\<UserName>\Local Settings\Application Data\assembly. If you have not done any WPF or Silverlight development, you may not find this particular folder on your machine.Project AssembliesThis is yet another folder where Visual Studio stores temporary files. You will find a folder for each project you have opened and worked on. This folder is located at <sysdrive>:\Documents and Settings\<UserName>Local Settings\Application Data\Microsoft\Visual Studio\[8|9].0\ProjectAssemblies on Windows XP. On Microsoft Vista/Windows 7 you will find this folder at <sysdrive>:\Users\<UserName>\AppData\Local\Microsoft\Visual Studio\[8|9].0\ProjectAssemblies.Remember not all of these folders will appear on your particular machine. Which ones do show up will depend on what version of Visual Studio you are using, whether or not you are doing desktop or web development, and the operating system you are using.SummaryTaking the time to periodically clean up after Visual Studio will aid in keeping your computer running quickly and increase the space on your hard drive. Another place to make sure you are cleaning up is your TEMP folder. Check your OS settings for the location of your particular TEMP folder and be sure to delete any files in here that are not in use. I routinely clean up the files and folders described in this blog post and I find that I actually eliminate errors in Visual Studio and I increase my hard disk space.NEW! PDSA has just published a “pre-release” of our PDSA Developer Utilities at http://www.pdsa.com/DeveloperUtilities that contains a Computer Cleaner utility which will clean up the above-mentioned folders, as well as a lot of other miscellaneous folders that get Visual Studio build-up. You can download a free trial at http://www.pdsa.com/DeveloperUtilities. If you wish to purchase our utilities through the month of November, 2011 you can use the RSVP code: DUNOV11 to get them for only $39. This is $40 off the regular price.NOTE: You can download this article and many samples like the one shown in this blog entry at my website. http://www.pdsa.com/downloads. Select “Tips and Tricks”, then “Developer Machine Clean Up” from the drop down list.Good Luck with your Coding,Paul Sheriff** SPECIAL OFFER FOR MY BLOG READERS **We frequently offer a FREE gift for readers of my blog. Visit http://www.pdsa.com/Event/Blog for your FREE gift!

    Read the article

  • SanjayP&rsquo;s venture after Microsoft involves no Microsoft

    - by eddraper
    When I was at Microsoft, I always found Sanjay Parthasarathy to be a bright and passionate leader.  While he was a bit disconnected at times with what was really going on out in the trenches, I always thought he was true believer in what we in Developer Platform and Evangelism (DPE) were doing.  He got it.  He had started DPE and kicked a lot of doors down up in Redmond to make it happen.  Back in the early 2000s, battles over platform choices at large customers was trench warfare… bayonets and hand grenades at the P-Code level.  This model was not at all suited to Microsoft’s org structure at the time.  While there were plenty of people fully able to have competitive conversations around Windows Server, or AD, or Exchange, or the desktop, there weren’t many that could have deep technical conversations around Java vs .NET and the platform “stack” as a cohesive, unified unit of value.  This task fell to DPE. Sanjay ended up leaving Microsoft a number of months before me in 2009 and I remember thinking these exact words: “holy shit, SanjayP left Microsoft.”  When SanjayP left DPE years before that,  Sheila Gulati had stepped into his shoes and I thought we where starting to miss a beat.  Sheila had built an amazing business at Microsoft India, but I don’t recall being inspired by her as a leader.  SanjayP’s talks felt like the opening scene of “Patton” with George C. Scott pacing in front of the American flag.  Sheila was a voice on a con-call.  When she moved on in 2007, Walid Abu-Hadba was given the reigns.  Personally, I don’t ever recall even seeing his face.  I think I might recall hearing his voice on some con-calls, but for all intents and purposes he was invisible to me.  Perhaps this was the beginning of my carelessness around seeking “visibility.” Fast forward to Build 2011.  First off, we have no PDC – we have Build.  Microsoft had made an 11 year investment by this time in building an organization to make its technology relevant to developers.  One would think such an org would be in the driver’s seat of such an event, but we see Windows product group people on the podiums.  Watching, I could see the messaging unfold… but no story.  It was like the old days.  Demos and PowerPoints by team members building the tech, and in many cases VPs.  The ensuing confusion is almost legendary now.  Windows 8 was, and is, a pretty big deal… but who is telling the story – not just features and benefits, but the story around how it all fits together. Having been out of Microsoft for two years now, and looking in, I can only conclude that the “DPE of old” has at best been emasculated, and at worst been completely marginalized by internal politics, or perhaps the eternal march of the corporate entropy generator that resides at all large companies.  I don’t think this is a good thing for anyone. And now, back to Sanjay who is the father of Microsoft DPE… I noticed that he has moved back to India and is doing start-up work.  His current company Indix looks to be doing some interesting things with “big data” and here’s their stack: Nary a trace of anything Microsoft.  What could account for this?  I wonder….  Better availability of labor and expertise in India for this stack?  Donno, but even in India, leet R and Hadoop skills have to be hard to find. Technical superiority?  This, I sincerely doubt. This stack, with SanjayP’s name as CEO leaves me with an unsettling feeling.  If he did believe, he no longer does.  One doesn’t place bets with real money on things they don’t believe in.  Perhaps he never did believe, and was a corporate creature seeking to find a niche for himself after which he manipulated me and others.  Or perhaps… anger… be it passive aggression or an outright “in your face F*** you” to his former masters. I guess in the end, only he knows the true reason… But I have my theory...

    Read the article

  • RIDC Accelerator for Portal

    - by Stefan Krantz
    What is RIDC?Remote IntraDoc Client is a Java enabled API that leverages simple transportation protocols like Socket, HTTP and JAX/WS to execute content service operations in WebCenter Content Server. Each operation by design in the Content Server will execute stateless and return a complete result of the request. Each request object simply specifies the in a Map format (key and value pairs) what service to call and what parameters settings to apply. The result responded with will be built on the same Map format (key and value pairs). The possibilities with RIDC is endless since you can consume any available service (even custom made ones), RIDC can be executed from any Java SE application that has any WebCenter Content Services needs. WebCenter Portal and the example Accelerator RIDC adapter frameworkWebCenter Portal currently integrates and leverages WebCenter Content Services to enable available use cases in the portal today, like Content Presenter and Doc Lib. However the current use cases only covers few of the scenarios that the Content Server has to offer, in addition to the existing use cases it is not rare that the customer requirements requires additional steps and functionality that is provided by WebCenter Content but not part of the use cases from the WebCenter Portal.The good news to this is RIDC, the second good news is that WebCenter Portal already leverages the RIDC and has a connection management framework in place. The million dollar question here is how can I leverage this infrastructure for my custom use cases. Oracle A-Team has during its interactions produced a accelerator adapter framework that will reuse and leverage the existing connections provisioned in the webcenter portal application (works for WebCenter Spaces as well), as well as a very comprehensive design patter to minimize the work involved when exposing functionality. Let me introduce the RIDCCommon framework for accelerating WebCenter Content consumption from WebCenter Portal including Spaces. How do I get started?Through a few easy steps you will be on your way, Extract the zip file RIDCCommon.zip to the WebCenter Portal Application file structure (PortalApp) Open you Portal Application in JDeveloper (PS4/PS5) select to open the project in your application - this will add the project as a member of the application Update the Portal project dependencies to include the new RIDCCommon project Make sure that you WebCenter Content Server connection is marked as primary (a checkbox at the top of the connection properties form) You should by this stage have a similar structure in your JDeveloper Application Project Portal Project PortalWebAssets Project RIDCCommon Since the API is coming with some example operations that has already been exposed as DataControl actions, if you open Data Controls accordion you should see following: How do I implement my own operation? Create a new Java Class in for example com.oracle.ateam.portal.ridc.operation call it (GetDocInfoOperation) Extend the abstract class com.oracle.ateam.portal.ridc.operation.RIDCAbstractOperation and implement the interface com.oracle.ateam.portal.ridc.operation.IRIDCOperation The only method you actually are required to implement is execute(RIDCManager, IdcClient, IdcContext) The best practice to set object references for the operation is through the Constructor, example below public GetDocInfoOperation(String dDocName)By leveraging the constructor you can easily force the implementing class to pass right information, you can also overload the Constructor with more or less parameters as required Implement the execute method, the work you supposed to execute here is creating a new request binder and retrieve a response binder with the information in the request binder.In this case the dDocName for which we want the DocInfo Secondly you have to process the response binder by extracting the information you need from the request and restore this information in a simple POJO Java BeanIn the example below we do this in private void processResult(DataBinder responseData) - the new SearchDataObject is a Member of the GetDocInfoOperation so we can return this from a access method. Since the RIDCCommon API leverage template pattern for the operations you are now required to add a method that will enable access to the result after the execution of the operationIn the example below we added the method public SearchDataObject getDataObject() - this method returns the pre processed SearchDataObject from the execute method  This is it, as you can see on the code below you do not need more than 32 lines of very simple code 1: public class GetDocInfoOperation extends RIDCAbstractOperation implements IRIDCOperation { 2: private static final String DOC_INFO_BY_NAME = "DOC_INFO_BY_NAME"; 3: private String dDocName = null; 4: private SearchDataObject sdo = null; 5: 6: public GetDocInfoOperation(String dDocName) { 7: super(); 8: this.dDocName = dDocName; 9: } 10:   11: public boolean execute(RIDCManager manager, IdcClient client, 12: IdcContext userContext) throws Exception { 13: DataBinder dataBinder = createNewRequestBinder(DOC_INFO_BY_NAME); 14: dataBinder.putLocal(DocumentAttributeDef.NAME.getName(), dDocName); 15: 16: DataBinder responseData = getResponseBinder(dataBinder); 17: processResult(responseData); 18: return true; 19: } 20: 21: private void processResult(DataBinder responseData) { 22: DataResultSet rs = responseData.getResultSet("DOC_INFO"); 23: for(DataObject dobj : rs.getRows()) { 24: this.sdo = new SearchDataObject(dobj); 25: } 26: super.setMessage(responseData.getLocal(ATTR_MESSAGE)); 27: } 28: 29: public SearchDataObject getDataObject() { 30: return this.sdo; 31: } 32: } How do I execute my operation? In the previous section we described how to create a operation, so by now you should be ready to execute the operation Step one either add a method to the class  com.oracle.ateam.portal.datacontrol.ContentServicesDC or a class of your own choiceRemember the RIDCManager is a very light object and can be created where needed Create a method signature look like this public SearchDataObject getDocInfo(String dDocName) throws Exception In the method body - create a new instance of GetDocInfoOperation and meet the constructor requirements by passing the dDocNameGetDocInfoOperation docInfo = new GetDocInfoOperation(dDocName) Execute the operation via the RIDCManager instance rMgr.executeOperation(docInfo) Return the result by accessing it from the executed operationreturn docInfo.getDataObject() 1: private RIDCManager rMgr = null; 2: private String lastOperationMessage = null; 3:   4: public ContentServicesDC() { 5: super(); 6: this.rMgr = new RIDCManager(); 7: } 8: .... 9: public SearchDataObject getDocInfo(String dDocName) throws Exception { 10: GetDocInfoOperation docInfo = new GetDocInfoOperation(dDocName); 11: boolean boolVal = rMgr.executeOperation(docInfo); 12: lastOperationMessage = docInfo.getMessage(); 13: return docInfo.getDataObject(); 14: }   Get the binaries! The enclosed code in a example that can be used as a reference on how to consume and leverage similar use cases, user has to guarantee appropriate quality and support.  Download link: https://blogs.oracle.com/ATEAM_WEBCENTER/resource/stefan.krantz/RIDCCommon.zip RIDC API Referencehttp://docs.oracle.com/cd/E23943_01/apirefs.1111/e17274/toc.htm

    Read the article

  • Windows Phone 7 development: first impressions

    - by DigiMortal
    After hard week in work I got some free time to play with Windows Phone 7 CTP developer tools. Although my first test application is still unfinished I think it is good moment to share my first experiences to you. In this posting I will give you quick overview of Windows Phone 7 developer tools from developer perspective. If you are familiar with Visual Studio 2010 then you will feel comfortable because Windows Phone 7 CTP developer tools base on Visual Studio 2010 Express. Project templates There are five project templates available. Three of them are based on Silverlight and two on XNA Game Studio: Windows Phone Application (Silverlight) Windows Phone List Application (Silverlight) Windows Phone Class Library (Silverlight) Windows Phone Game (XNA Game Studio) Windows Phone Game Library (XNA Game Studio) Currently I am writing to test applications. One of them is based on Windows Phone Application and the other on Windows Phone List Application project template. After creating these projects you see the following views in Visual Studio. Windows Phone Application. Click on image to enlarge. Windows Phone List Application. Click on image to enlarge.  I suggest you to use some of these templates to get started more easily. Windows Phone 7 emulator You can run your Windows Phone 7 applications on Windows Phone 7 emulator that comes with developer tools CTP. If you run your application then emulator is started automatically and you can try out how your application works in phone-like emulator. You can see screenshot of emulator on right. Currently there is opened Windows Phone List Application as it is created by default. Click on image to enlarge it. Emulator is a little bit slow and uncomfortable but it works pretty well. This far I have caused only couple of crashes during my experiments. In these cases emulator works but Visual Studio gets stuck because it cannot communicate with emulator. One important note. Emulator is based on virtual machine although you can see only phone screen and options toolbar. If you want to run emulator you must close all virtual machines running on your machine and run Visual Studio 2010 as administrator. Once you run emulator you can keep it open because you can stop your application in Visual Studio, modify, compile and re-deploy it without restarting emulator. Designing user interfaces You can design user interface of your application in Visual Studio. When you open XAML-files it is displayed in window with two panels. Left panel shows you device screen and works as visual design environment while right panel shows you XAML mark-up and let’s you modify XML if you need it. As it is one of my very first Silverlight applications I felt more comfortable with XAML editor because property names in property boxes of visual designer confused me a little bit. Designer panel is not very good because it is visually hard to follow. It has black background that makes dark borders of controls very hard to see. If you have monitor with very high contrast then it is may be not a real problem. I have usual monitor and I have problem. :) Putting controls on design surface, dragging and resizing them is also pretty painful. Some controls are drawn correctly but for some controls you have to set width and height in XML so they can be resized. After some practicing it is not so annoying anymore. On the right you can see toolbox with some controllers. This is all you get out of the box. But it is sufficient to get started. After getting some experiences you can create your own controls or use existing ones from other vendors or developers. If it is your first time to do stuff with Silverlight then keep Google open – you need it hard. After getting over the first shock you get the point very quickly and start developing at normal speed. :) Writing source code Writing source code is the most familiar part of this action. Good old Visual Studio code editor with all nice features it has. But here you get also some surprises: The anatomy of Silverlight controls is a little bit different than the one of user controls in web and forms projects. Windows Phone 7 doesn’t run on full version of Windows (I bet it is some version of Windows CE or something like this) then there is less system classes you can use. Some familiar classes have less methods that in full version of .NET Framework and in these cases you have to write all the code by yourself or find libraries or source code from somewhere. These problems are really not so much problems than limitations and you get easily over them. Conclusion Windows Phone 7 CTP developer tools help you do a lot of things on Windows Phone 7. Although I expected better performance from tools I think that current performance is not a problem. This far my first test project is going very well and Google has answer for almost every question. Windows Phone 7 is mobile device and therefore it has less hardware resources than desktop computers. This is why toolset is so limited. The more you need memory the more slower is device and as you may guess it needs the more battery. If you are writing apps for mobile devices then make your best to get your application use as few resources as possible and act as fast as possible.

    Read the article

  • My Tech Ed North America Preview - Content Edition

    - by Chris Gardner
    As I promised in my last post, I feel the need to give you a rundown on all the technical content I am looking forward to checking out at Tech Ed this year. We shall start with the content I know I'll be able to see. This would be some demo stations in the Technical Learning Center. I will DEFINITELY be checking out the Windows Phone Device Bar. I will admit that I am a bit of a phone snob, and I just want to manhandle all that sexy, sexy tech. I am also planning on talking to the Windows Phone team and the Azure team. Year after year, I end up spending more time in either the TLC or taking certification tests than anywhere else. This leads me to the one "Exam Cram" session I hope to attend. There is a session to cram for 70-599: Designing and Developing Windows Phone Applications. I know this seems odd. I'm (sort of) an XNA guru. However, I'm not that up on my Silverlight. I know enough to add Silverlight to an XNA project. Now, let's talk breakout sessions. We always need to keep track of where we're going. I know, I talk about solving problems over forcing buzz words. However, it is important to know what those buzz words before you tell people not to use them. For this, we will look to the "What's New in Visual Studio 11" and "What's New in Microsoft .NET Framework 4.5." Of course, we do talk bad about buzz words around here. For this, I'm really looking forward to "Visual C#/Visual Basic: Becoming a Guru with Existing Features." I still have .NET 2 tricks that are crucial to my internal libraries. In depth knowledge will NEVER trump shortcut libraries. There is a session in ASP.NET for phones and tablets. For those of you that have not tried to use ASP.NET on a mobile device, there is one thing you really need to understand. Mobile devices don't use scroll bars. That's right; the thing with the least screen real estate doesn't use scroll bars. Thus, I am hoping this session will give some good advice in having an ASP.NET site target both mobile and desktop. The last "business only" session "The Accidental Team Foundation Server Admin." T & W Operations is a VERY small business. As such, I am the TFS admin because I'm the developer that is also the SQL Guru. I keep my server up, but it'd be nice to know some really cool tricks for the part time guy. This leads us the the fun sessions. Coding4Fun has a Kinect session. The Twitter followers will remember that I now have a Kinect for Windows sitting on my desk at work. I have gotten pretty handy with the device, but I KNOW I'm missing some good stuff. Finally, we come to Brian Prince's session on "Making Crazy Money with Games and the Cloud." Never mind the fact that we're using Azure at work. Never mind the fact that I'm actually using the cloud in a game. Never mind the fact that the session has the terms "Crazy Money" and "Games" in the title. If you've never seen Brian Prince speak, you're missing out. In the Hands-on-Labs, we are not allowed to make our own schedule. Instead, we're asked what sessions we can't miss, and they try to schedule around those times. This was the one session I said I couldn't miss. This should complete the technical content for the conference. Coming soon, I'll dig into the certifications I hope to attain. Then, we'll talk about the social activities for the week. Here's a preview of that. I am a member of The Krewe...

    Read the article

  • Geocaching - World wide treasure hunt

    I'm not quite sure how I came across this topic but actually I find it absolutely interesting, challenging and most of all a great fun for the family and friends. The interesting part is for sure that you can follow other peoples treasures and their preferred locations where a cache might be hidden. Of course, it wont be easy to find a cache after all. Sometimes there are even 'mystery caches' which have either riddles, further instructions or little brain games for you in order to find the actual cache - that's the challenge. And last but not least, those caches are hidden outdoor. A great experience to explore nature either on your own, or your family especially with children, or as a treasure hunting pack with a couple of friends. What is geocaching? It's a high-tech outdoor treasure hunting game that's a great way to explore the world with friends, family or on your own. Participants use GPS-enabled devices to locate hidden containers called geocaches. There are over one million geocaches hidden around the world today, waiting for you to find them. Visit Geocaching.com to search for geocaches near you.(Source: Referral Email of geocaching.com) Checkout the Geocaching 101 for further details and information. They also provide a video channel on YouTube. Which equipment do I need? Any GPS-enabled device is sufficient to go onto the hunt. I'm going to start our geocaching experience equipped with my Samsung Galaxy Tab. Additionally, I installed a geocaching.com client called c:geo that hopefully assists me soon. Combined with a map app like Google Maps and a nice Compass app you should be fully equipped and ready to go. I guess, that even a car navigation system is perfect for that task. Later on, with more experience and demand for technology (or precision) it might be interesting to opt-in for a pure GPS device, like a Garmin or any other brand on the market. {loadposition content_adsense} What is a geocache and what does it contain? In its simplest form, a cache always contains a logbook or logsheet for you to log your find. Larger caches may contain a logbook and any number of items. These items turn the adventure into a true treasure hunt. You never know what the cache owner or visitors to the cache may have left for you to enjoy. Remember, if you take something, leave something of equal or greater value in return. It is recommended that items in a cache be individually packaged in a clear, zipped plastic bag to protect them from the elements. Finding your first geocache Well, first you have to have interest to pick up the challenge. Then you have to check out the Geocache directory on geocaching.com. They have recommendations for beginner's caches but you are free to choose any. Actually, we have a Mystery Cache very close to our base, and I guess that we are going for that one on our first trip. Anyway, there is a very informative guide on the website which should answer all your questions about starting your new outdoor adventure. For sure, it's going to be rewarding. Team up with friends and family Especially as a beginner there might be misunderstandings in handling the GPS coordinates, the compass, or the map, and even finding the container at the documented position isn't easy in the first place. Luckily, there are logbook reports online from other hunters, and most of the time there are even 'spoiler' images available. But also bear in mind, that a geocache might have been removed or is lost due to unconscious people or whatever other reasons. Don't be disappointed in case that you can't find anything... There be nothing anymore. A general recommendation in this case would be to replace the missing container with a new one, and give feedback to the original owner about the state of that particular location. After all, it's about fun and active participation in a world-wide community. Geocaches in Mauritius? Yes, there are currently about 45 geocaches spread all over the island, and even a single in Rodriguez - that's gonna be a tough one. Hopefully, we will get increasing numbers as Geocaching.com allows, no better, even encourages you to hide new containers at your locations of choice. I think this is going to be real fun for us during the upcoming weeks and months. Especially, when we are travelling to other countries and transfer so-called trackable items between geocaches. On my first impression, Geocaching.com seems to be very mature, open and community-oriented. There are literally hundreds of thousands geocache 'hunters' all over the world. And usually finding a container remote from your home is very rewarding. I'll keep you updated in these matters during the next months to come...

    Read the article

  • Silverlight 5 &ndash; What&rsquo;s New? (Including Screenshots &amp; Code Snippets)

    - by mbcrump
    Silverlight 5 is coming next year (2011) and this blog post will tell you what you need to know before the beta ships. First, let me address people saying that it is dead after PDC 2010. I believe that it’s best to see what the market is doing, not the vendor. Below is a list of companies that are developing Silverlight 4 applications shown during the Silverlight Firestarter. Some of the companies have shipped and some haven’t. It’s just great to see the actual company names that are working on Silverlight instead of “people are developing for Silverlight”. The next thing that I wanted to point out was that HTML5, WPF and Silverlight can co-exist. In case you missed Scott Gutherie’s keynote, they actually had a slide with all three stacked together. This shows Microsoft will be heavily investing in each technology.  Even I, a Silverlight developer, am reading Pro HTML5. Microsoft said that according to the Silverlight Feature Voting site, 21k votes were entered. Microsoft has implemented about 70% of these votes in Silverlight 5. That is an amazing number, and I am crossing my fingers that Microsoft bundles Silverlight with Windows 8. Let’s get started… what’s new in Silverlight 5? I am going to show you some great application and actual code shown during the Firestarter event. Media Hardware Video Decode – Instead of using CPU to decode, we will offload it to GPU. This will allow netbooks, etc to play videos. Trickplay – Variable Speed Playback – Pitch Correction (If you speed up someone talking they won’t sound like a chipmunk). Power Management – Less battery when playing video. Screensavers will no longer kick in if watching a video. If you pause a video then screensaver will kick in. Remote Control Support – This will allow users to control playback functions like Pause, Rewind and Fastforward. IIS Media Services 4 has shipped and now supports Azure. Data Binding Layout Transitions – Just with a few lines of XAML you can create a really rich experience that is not using Storyboards or animations. RelativeSource FindAncestor – Ancestor RelativeSource bindings make it much easier for a DataTemplate to bind to a property on a container control. Custom Markup Extensions – Markup extensions allow code to be run at XAML parse time for both properties and event handlers. This is great for MVVM support. Changing Styles during Runtime By Binding in Style Setters – Changing Styles at runtime used to be a real pain in Silverlight 4, now it’s much easier. Binding in style setters allows bindings to reference other properties. XAML Debugging – Below you can see that we set a breakpoint in XAML. This shows us exactly what is going on with our binding.  WCF & RIA Services WS-Trust Support – Taken from Wikipedia: WS-Trust is a WS-* specification and OASIS standard that provides extensions to WS-Security, specifically dealing with the issuing, renewing, and validating of security tokens, as well as with ways to establish, assess the presence of, and broker trust relationships between participants in a secure message exchange. You can reduce network latency by using a background thread for networking. Supports Azure now.  Text and Printing Improved text clarity that enables better text rendering. Multi-column text flow, Character tracking and leading support, and full OpenType font support.  Includes a new Postscript Vector Printing API that provides control over what you print . Pivot functionality baked into Silverlight 5 SDK. Graphics Immediate mode graphics support that will enable you to use the GPU and 3D graphics supports. Take a look at what was shown in the demos below. 1) 3D view of the Earth – not really a real-world application though. A doctor’s portal. This demo really stood out for me as it shows what we can do with the 3D / GPU support. Out of Browser OOB applications can now create and manage childwindows as shown in the screenshot below.  Trusted OOB applications can use P/Invoke to call Win32 APIs and unmanaged libraries.  Enterprise Group Policy Support allow enterprises to lock down or up the sandbox capabilities of Silverlight 5 applications. In this demo, he tore the “notes” off of the application and it appeared in a new window. See the black arrow below. In this demo, he connected a USB Device which fired off a local Win32 application that provided the data off the USB stick to Silverlight. Another demo of a Silverlight 5 application exporting data right into Excel running inside of browser. Testing They demoed Coded UI, which is available now in the Visual Studio Feature Pack 2. This will allow you to create automated testing without writing any code manually. Performance: Microsoft has worked to improve the Silverlight startup time. Silverlight 5 provides 64-bit browser support.  Silverlight 5 also provides IE9 Hardware acceleration.   I am looking forward to Silverlight 5 and I hope you are too. Thanks for reading and I hope you visit again soon.  Subscribe to my feed CodeProject

    Read the article

  • OPN Oracle ECM 10g R3 Implementation Boot Camp - (12-14/Abr/10)

    - by Claudia Costa
    É com entusiasmo que lhe anunciamos o bootcamp de Oracle ECM 10g R3 Implementation que irá realizar nos dias 12-14 de Abril  que abordará os tópicos abaixo descritos. Com o objectivo de ajudar os parceiros a desenvolver competências, a Oracle University e a Oracle Alliances&Channel, desenharam este bootcamp, compactando os conteúdos e reduzindo assim os custos. Preço por participante (3 dias) - 1.250 Eur + Iva  Oracle offers the most unified, usable enterprise content management platform in today's market. With centralized control across single or multiple repositories, common core functionality, and easily scalable content management capabilities, Oracle provides content management solutions for many content types and users-wherever they work in the enterprise.   The Oracle Enterprise Content Management (ECM) Implementation Boot Camp examines the fundamental concepts, techniques, and architecture of Oracle's ECM technologies. Join this training to learn how you can manage and maintain unstructured content   Target Audience:  The Oracle ECM Implementation Boot Camp is designed for architects, technical consultants, team/project leaders and functional consultants of our system integrator partners who want to ramp-up on ECM technology.   Contents:  The ECM Implementation Boot Camp is a three-day hands-on workshop, designed for Oracle Partners who are new to ECM, and will provide implementation instruction on the ECM technology offered by Oracle. The boot camp will: • Provide hands-on experience in implementing Oracle's truly unified, open and standard base ECM technology • Provide the strategic direction about Oracle's Fusion Middleware/Enterprise 2.0 and its role in composite application development • Expose broad set of Oracle's ECM technologies.   Objectives: The Oracle ECM Implementation Boot Camp is primarily focused on the Oracle's ECM offering to manage and maintain unstructured content and covers Universal Content Management (UCM), Image and Process Management (IPM), Universal Records Management (URM), and Information Rights Management (IRM):   Topics Covered • Introduction to Oracle UCM o UCM Overview o UCM Architecture Overview • Content Server and Document Management basics o Installation and Administration Skills § User and Security Admin § Configuration (metadata, DCLs, profiles, rules, etc.) § Workflow Admin § System Properties and Component Manager § Managing Subscriptions o Contributing Content § Browser form § WebDAV folder § Desktop Integration o Searching • Web Content Management o Site Studio • Universal Records Management • Information Right Management (IRM) • Image & Process Management (IPM) • Oracle Document Capture • Oracle eMail Archive Service. Labs • Content Server Installation • Use and Administration of Content Server • Introduction to Site Studio • Use and Administration of Records Manager Demo: The R&D Group and the New Patent Focus: Information Rights Management, Knowledge Management, Accounts Payable Image Automation, Imaging and Process Management Case Study Use Case 1: Enable City of Xalco to streamline internal processes by empowering city employees to quickly and efficiently manage and publish information on their employee intranet and eventually public Web site. Use Case 2: Help Acme & Co in archiving its goal is to become "paperless" by managing all of their company's business content in a central, Web-based repository. Acme's business content ranges from policies and procedures to Employee listings and marketing materials.   Agenda: Day 1 ·         ECM Overview & Content Server ·         ECM Overview ·         ECM Architecture and Installation ·         UCM and Digital Asset Management DEMO ·         Lab 1 - Content Server Installation ·         Lab 2 - Use and Administration of Content Server   Day 2 ·         Web Content Management ·         Lab 2 - Use and Administration of Content ·         Server (continued) ·         Introduction to Web Content Management ·         Lab 3 - Site Studio   Day 3 ·         URM/IRM/IPM ·         Introduction to Universal Records Management ·         Lab 4 - URM ·         Introduction to Information Rights Management ·         Information Rights Management DEMO ·         Introduction to Image and Process Management ·         Image and Process Management Demo ·         Oracle Document Capture ·         Oracle eMail Archive   Material needed for Bootcamp: This Boot camp requires attendees to provide their own laptops for this class. Attendee laptops must meet the following minimum hardware/software requirements: Hardware • RAM: 2GB RM minimum (1 GB RAM is not enough) • HDD: 15 GB free HDD space   Pre requistes: To ensure a valuable learning experience, participation in this boot camp requires completing the prerequisite courses and successfully passing the prerequisite assessment test that is mapped into the Oracle Enterprise Content Management Implementation Boot Camp guided learning path. At a minimum, participants with equivalent skills and background should review the guided learning path and successfully pass the prerequisite assessment test to ensure they possess the background necessary to benefit from participation in the boot Camp.   ---------------------------------------------------------------------   Para mais informações/inscrições, contacte: Mónica Pires  21 423 51 44 Horário e Local 9:30h - 12:30h e 14:00h - 17:00 ( 6 horas/dia )Oracle, Porto Salvo - Oeiras.

    Read the article

  • Juniper Strategy, LLC is hiring SharePoint Developers&hellip;

    - by Mark Rackley
    Isn’t everybody these days? It seems as though there are definitely more jobs than qualified devs these days, but yes, we are looking for a few good devs to help round out our burgeoning SharePoint team. Juniper Strategy is located in the DC area, however we will consider remote devs for the right fit. This is your chance to get in on the ground floor of a bright company that truly “gets it” when it comes to SharePoint, Project Management, and Information Assurance. We need like-minded people who “get it”, enjoy it, and who are looking for more than just a job. We have government and commercial opportunities as well as our own internal product that has a bright future of its own. Our immediate needs are for SharePoint .NET developers, but feel free to submit your resume for us to keep on file as it looks as though we’ll need several people in the coming months. Please email us your resume and salary requirements to [email protected] Below are our official job postings. Thanks for stopping by, we look forward to  hearing from you. Senior SharePoint .NET Developer Senior developer will focus on design and coding of custom, end-to-end business process solutions within the SharePoint framework. Senior developer with the ability to serve as a senior developer/mentor and manage day-to-day development tasks. Work with business consultants and clients to gather requirements to prepare business functional specifications. Analyze and recommend technical/development alternative paths based on business functional specifications. For selected development path, prepare technical specification and build the solution. Assist project manager with defining development task schedule and level-of-effort. Lead technical solution deployment. Job Requirements Minimum of 7 years experience in agile development, with at least 3 years of SharePoint-related development experience (SPS, SharePoint 2007/2010, WSS2-4). Thorough understanding of and demonstrated experience in development under the SharePoint Object Model, with focus on the WSS 3.0 foundation (MOSS 2007 Standard/Enterprise, Project Server 2007). Experience with using multiple data sources/repositories for database CRUD activities, including relational databases, SAP, Oracle e-Business. Experience with designing and deploying performance-based solutions in SharePoint for business processes that involve a very large number of records. Experience designing dynamic dashboards and mashups with data from multiple sources (internal to SharePoint as well as from external sources). Experience designing custom forms to facilitate user data entry, both with and without leveraging Forms Services. Experience building custom web part solutions. Experience with designing custom solutions for processing underlying business logic requirements including, but not limited to, SQL stored procedures, C#/ASP.Net workflows/event handlers (including timer jobs) to support multi-tiered decision trees and associated computations. Ability to create complex solution packages for deployment (e.g., feature-stapled site definitions). Must have impeccable communication skills, both written and verbal. Seeking a "tinkerer"; proactive with a thirst for knowledge (and a sense of humor). A US Citizen is required, and need to be able to pass NAC/E-Verify. An active Secret clearance is preferred. Applicants must pass a skills assessment test. MCP/MCTS or comparable certification preferred. Salary & Travel Negotiable SharePoint Project Lead Define project task schedule, work breakdown structure and level-of-effort. Serve as principal liaison to the customer to manage deliverables and expectations. Day-to-day project and team management, including preparation and maintenance of project plans, budgets, and status reports. Prepare technical briefings and presentation decks, provide briefs to C-level stakeholders. Work with business consultants and clients to gather requirements to prepare business functional specifications. Analyze and recommend technical/development alternative paths based on business functional specifications. The SharePoint Project Lead will be working with SharePoint architects and system owners to perform requirements/gap analysis and develop the underlying functional specifications. Once we have functional specifications as close to "final" as possible, the Project Lead will be responsible for preparation of the associated technical specification/development blueprint, along with assistance in preparing IV&V/test plan materials with support from other team members. This person will also be responsible for day-to-day management of "developers", but is also expected to engage in development directly as needed.  Job Requirements Minimum 8 years of technology project management across the software development life-cycle, with a minimum of 3 years of project management relating specifically to SharePoint (SPS 2003, SharePoint2007/2010) and/or Project Server. Thorough understanding of and demonstrated experience in development under the SharePoint Object Model, with focus on the WSS 3.0 foundation (MOSS 2007 Standard/Enterprise, Project Server 2007). Ability to interact and collaborate effectively with team members and stakeholders of different skill sets, personalities and needs. General "development" skill set required is a fundamental understanding of MOSS 2007 Enterprise, SP1/SP2, from the top-level of skinning to the core of the SharePoint object model. Impeccable communication skills, both written and verbal, and a sense of humor are required. The projects will require being at a client site at least 50% of the time in Washington DC (NW DC) and Maryland (near Suitland). A US Citizen is required, and need to be able to pass NAC/E-Verify. An active Secret clearance is preferred. PMP certification, PgMP preferred. Salary & Travel Negotiable

    Read the article

  • Getting Started with Prism (aka Composite Application Guidance for WPF and Silverlight)

    - by dotneteer
    Overview Prism is a framework from the Microsoft Patterns and Practice team that allow you to create WPF and Silverlight in a modular way. It is especially valuable for larger projects in which a large number of developers can develop in parallel. Prism achieves its goal by supplying several services: · Dependency Injection (DI) and Inversion of control (IoC): By using DI, Prism takes away the responsibility of instantiating and managing the life time of dependency objects from individual components to a container. Prism relies on containers to discover, manage and compose large number of objects. By varying the configuration, the container can also inject mock objects for unit testing. Out of the box, Prism supports Unity and MEF as container although it is possible to use other containers by subclassing the Bootstrapper class. · Modularity and Region: Prism supplies the framework to split application into modules from the application shell. Each module is a library project that contains both UI and code and is responsible to initialize itself when loaded by the shell. Each window can be further divided into regions. A region is a user control with associated model. · Model, view and view-model (MVVM) pattern: Prism promotes the user MVVM. The use of DI container makes it much easier to inject model into view. WPF already has excellent data binding and commanding mechanism. To be productive with Prism, it is important to understand WPF data binding and commanding well. · Event-aggregation: Prism promotes loosely coupled components. Prism discourages for components from different modules to communicate each other, thus leading to dependency. Instead, Prism supplies an event-aggregation mechanism that allows components to publish and subscribe events without knowing each other. Architecture In the following, I will go into a little more detail on the services provided by Prism. Bootstrapper In a typical WPF application, application start-up is controls by App.xaml and its code behind. The main window of the application is typically specified in the App.xaml file. In a Prism application, we start a bootstrapper in the App class and delegate the duty of main window to the bootstrapper. The bootstrapper will start a dependency-injection container so all future object instantiations are managed by the container. Out of box, Prism provides the UnityBootstrapper and MefUnityBootstrapper abstract classes. All application needs to either provide a concrete implementation of one of these bootstrappers, or alternatively, subclass the Bootstrapper class with another DI container. A concrete bootstrapper class must implement the CreateShell method. Its responsibility is to resolve and create the Shell object through the DI container to serve as the main window for the application. The other important method to override is ConfigureModuleCatalog. The bootstrapper can register modules for the application. In a more advance scenario, an application does not have to know all its modules at compile time. Modules can be discovered at run time. Readers to refer to one of the Open Modularity Quick Starts for more information. Modules Once modules are registered with or discovered by Prism, they are instantiated by the DI container and their Initialize method is called. The DI container can inject into a module a region registry that implements IRegionViewRegistry interface. The module, in its Initialize method, can then call RegisterViewWithRegion method of the registry to register its regions. Regions Regions, once registered, are managed by the RegionManager. The shell can then load regions either through the RegionManager.RegionName attached property or dynamically through code. When a view is created by the region manager, the DI container can inject view model and other services into the view. The view then has a reference to the view model through which it can interact with backend services. Service locator Although it is possible to inject services into dependent classes through a DI container, an alternative way is to use the ServiceLocator to retrieve a service on demard. Prism supplies a service locator implementation and it is possible to get an instance of the service by calling: ServiceLocator.Current.GetInstance<IServiceType>() Event aggregator Prism supplies an IEventAggregator interface and implementation that can be injected into any class that needs to communicate with each other in a loosely-coupled fashion. The event aggregator uses a publisher/subscriber model. A class can publishes an event by calling eventAggregator.GetEvent<EventType>().Publish(parameter) to raise an event. Other classes can subscribe the event by calling eventAggregator.GetEvent<EventType>().Subscribe(EventHandler, other options). Getting started The easiest way to get started with Prism is to go through the Prism Hands-On labs and look at the Hello World QuickStart. The Hello World QuickStart shows how bootstrapper, modules and region works. Next, I would recommend you to look at the Stock Trader Reference Implementation. It is a more in depth example that resemble we want to set up an application. Several other QuickStarts cover individual Prism services. Some scenarios, such as dynamic module discovery, are more advanced. Apart from the official prism document, you can get an overview by reading Glen Block’s MSDN Magazine article. I have found the best free training material is from the Boise Code Camp. To be effective with Prism, it is important to understands key concepts of WPF well first, such as the DependencyProperty system, data binding, resource, theme and ICommand. It is also important to know your DI container of choice well. I will try to explorer these subjects in depth in the future. Testimony Recently, I worked on a desktop WPF application using Prism. I had a wonderful experience with Prism. The Prism is flexible enough even in the presence of third party controls such as Telerik WPF controls. We have never encountered any significant obstacle.

    Read the article

  • HTG Explains: Are You Using IPv6 Yet? Should You Even Care?

    - by Chris Hoffman
    IPv6 is extremely important for the long-term health of the Internet. But is your Internet service provider providing IPv6 connectivity yet? Does your home network support it? Should you even care if you’re using IPv6 yet? Switching from IPv4 to IPv6 will give the Internet a much larger pool of IP addresses. It should also allow every device to have its own public IP address, rather than be hidden behind a NAT router. IPv6 is Important Long-Term IPv6 is very important for the long-term health of the Internet. There are only about 3.7 billion public IPv4 addresses. This may sound like a lot, but it isn’t even one IP address for each person on the planet. Considering people have more and more Internet-connected devices — everything from light bulbs to thermostats are starting to become network-connected — the lack of IP addresses is already proving to be a serious problem. This may not affect those of us in well-off developed countries just yet, but developing countries are already running out of IPv4 addresses. So, if you work at an Internet service provider, manage Internet-connected servers, or develop software or hardware — yes, you should care about IPv6! You should be deploying it and ensuring your software and hardware works properly with it. It’s important to prepare for the future before the current IPv4 situation becomes completely unworkable. But, if you’re just typical user or even a typical geek with a home Internet connection and a home network, should you really care about your home network just yet? Probably not. What You Need to Use IPv6 To use IPv6, you’ll need three things: An IPv6-Compatible Operating System: Your operating system’s software must be capable of using IPv6. All modern desktop operating systems should be compatible — Windows Vista and newer versions of Windows, as well as modern versions of Mac OS X and Linux. Windows XP doesn’t have IPv6 support installed by default, but you shouldn’t be using Windows XP anymore, anyway. A Router With IPv6 Support: Many — maybe even most — consumer routers in the wild don’t support IPv6. Check your router’s specifications details to see if it supports IPv6 if you’re curious. If you’re going to buy a new router, you’ll probably want to get one with IPv6 support to future-proof yourself. If you don’t have an IPv6-enabled router yet, you don’t need to buy a new one just to get it. An ISP With IPv6 Enabled:  Your Internet service provider must also have IPv6 set up on their end. Even if you have modern software and hardware on your end, your ISP has to provide an IPv6 connection for you to use it. IPv6 is rolling out steadily, but slowly — there’s a good chance your ISP hasn’t enabled it for you yet. How to Tell If You’re Using IPv6 The easiest way to tell if you have IPv6 connectivity is to visit a website like testmyipv6.com. This website allows you to connect to it in different ways — click the links near the top to see if you can connect to the website via different types of connections. If you can’t connect via IPv6, it’s either because your operating system is too old (unlikely), your router doesn’t support IPv6 (very possible), or because your ISP hasn’t enabled it for you yet (very likely). Now What? If you can connect to the test website above via IPv6, congratulations! Everything is working as it should. Your ISP is doing a good job of rolling out IPv6 rather than dragging its feet. There’s a good chance you won’t have IPv6 working properly, however. So what should you do about this — should you head to Amazon and buy a new IPv6-enabled router or switch to an ISP that offers IPv6? Should you use a “tunnel broker,” as the test site recommends, to tunnel into IPv6 via your IPv4 connection? Well, probably not. Typical users shouldn’t have to worry about this yet. Connecting to the Internet via IPv6 shouldn’t be perceptibly faster, for example. It’s important for operating system vendors, hardware companies, and Internet service providers to prepare for the future and get IPv6 working, but you don’t need to worry about this on your home network. IPv6 is all about future-proofing. You shouldn’t be racing to implement this at home yet or worrying about it too much — but, when you need to buy a new router, try to buy one that supports IPv6. Image Credit: Adobe of Chaos on Flickr, hisperati on Flickr, Vox Efx on Flickr     

    Read the article

< Previous Page | 712 713 714 715 716 717 718 719 720 721 722 723  | Next Page >