Search Results

Search found 3413 results on 137 pages for 'addresses'.

Page 72/137 | < Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79  | Next Page >

• Prevent Sending Spam with my Yahoo Account?

  - by Mohammad

  Today morning I found my Yahoo Mail account sent several emails with Subject re: and this body : this is crazy you should give it a look http://www.wanews15.net/biz/?news=9080205 to all my contact emails !!! I have Eset Nod32(Up to date) Anti Virus, but it couldn't find any thing. I've installed Microsoft Security Essential and it could find a virus. I remove it and I change my mail password. What happened to my Yahoo Mail Account and what should I do ? Edit : My email password was 12 characters and I couldn't remember it , so I'm using RoboForm. Is it possible that my Roboform password divulge. !!! Edit 2 : I've changed my yahoo mail password, but this morning I received Failure Notice for sending mail to some invalid mail addresses again, but there is a different this time, the sent mails didn't exist in my Sent Box. Is it a good thing or I have to do something else ?

  Read the article

• Windows file sharing connects over WiFi instead of LAN

  - by zacaj

  I have a laptop and a desktop computer, and I need to sync lots of files to the laptop and back whenever I go on a trip, etc. I've got a LAN cable connected into an extra port on the desktop that I plug into the laptop so I can get gigabit file transfers instead of wireless G. They connect fine. If I do an FTP transfer, for instance, using the LAN IP addresses, it goes at ~40MB/s, as it should. However when I copy files using explorer and native windows file sharing it detects the other computer by name, not IP (eg \\DESKTOP-PC\ instead of \\192.168.0.100\) and always connects to it by its wireless IP address instead of the faster LAN address. Both computers are running Windows 7. I have tried editing the priorities of the adapters in Advanced Settings and putting the LAN adapters above the wifi ones, but this didn't have any effect

  Read the article

• setting up a WGR614v7 behind a linux box

  - by commodore fancypants

  Here's the setup, I have an openSUSE box with 2 NICs, one goes to my home network router, the other has DHCP running and it attached to a wireless router. I'm trying to get this setup to work before I switch to the linux box as my home network router. My DHCP will offer the wireless router (a WGR614v7) an address, but anything that connects to the wireless router ends up with a APIPA address. I have all the firewalls on the wireless network turned off as well as the wireless router's own DHCP. The linux box isn't offering addresses to anything past the wireless router. Is this a problem with the router or my DHCP setup? For testing purposes, I have both NICs set in the internal zone and I've tried wireless and wired connections to the WGR614v7 both to no avail.

  Read the article

• How to place additional access-restrictions on a subdirectory in Apache?

  - by Mikhail T.

  We have a list of "internal" IP-addresses and only allow access to the server (Location /) from that list: <Location /> Require ip x.x.x.x Require ip y.y.y.y </Location> I need to further restrict access to a sub-directory (Location /foo) to authenticated users (Require valid-user). Whatever I do, I never get prompted for login to access /foo -- Apache simply grants me access, because my IP-address is on the list (for Location /). I cycled through all three different values of AuthMerging (off, and, or) to no avail... Must be something really stupid :-/ Using httpd-2.4.6. Thank you!

  Read the article

• Forward emails from specific domain in Exchange

  - by neildeadman

  Our Exchange server handles emails for @ourdomain.com (for example). We have multiple clients that will send emails to our [email protected] email address and we want to configure server-side rules that will forward emails from each client's domain to a different email address within our exchange server. For example: [email protected] sends an email to [email protected] and we forward it to [email protected] [email protected] sends an email to [email protected] and we forward it to [email protected] ...and so on. It would be nice if we can additionally stop the email arriving in the [email protected] mailbox, but that is not a specific requirement. We have a rule setup in Outlook that sort of works, but it doesn't do all from a domain only specific email addresses. It does work when Outlook is not running which is a start. I realise it would be easier to give each client a partiuclar email address and have them email straight to that rather than all use the same, but this is what I have been asked to setup.... :S

  Read the article

• SSH tunnel & Rsync thru two proxy/firewalls

  - by cajwine

  Screnario: [internal_server_1]AA------AB[firewall_1]AC----+ 10.2.0.3-^ ^-10.2.0.2 | internet 10.3.0.3-v v-10.3.0.2 | [internal_server_2]BA------BB[firewall_2]BC----+ Ports AC,BC has valid internet addresses. All systems run linux and have root acces to all. Need securely rsync internal_server_1:/some/path into internal_server_2:/another/path My idea is make ssh secure tunnel between two firewalls, e.g. from firewall_1 firewall1# ssh -N -p 22 -c 3des user2@firewall_2.example.com -L xxx/10.3.0.3/xxxx and after will run rsync from internal_server_1 somewhat like: intenal1# rsync -az /some/path [email protected]:/another/path I don't know how to make a correct ssh tunnel for rsync (what ports need tunnel) and to where i will make the rsync? (remote comp address in case of ssh tunnel) Any idea or pointer to helpfull internet resource for this case? thanx.

  Read the article

• How to disable autocmd or augroup in vim?

  - by Andrew Vit

  Given I have a group of commands such as: augroup MyGroup autocmd CursorMoved * silent call MyCommandOne() augroup END I want to disable all the autocommands in MyGroup for a time and then re-enable it later. Is there anything I can do with the group? Specifically, is there a way to disable the whole group at once? If not, what can I do to disable individual commands? Looking at the help, I only see a few options: augroup! will delete the whole group: I don't think this is right since I will want to re-enable it again. (But maybe there's a way to easily redefine the group again?) :noautocmd will only disable the callbacks for a one-off invocation of a command. (And it disables all autocmds, not specified ones) eventignore addresses the event binding, not the command: it sounds like it disables all bound commands for a given event, not just one command or a group I can specify. How is this done?

  Read the article

• apxs cannot install mod_cloudflare on centos

  - by Adam

  [ Linux - CentOS - Apache 2.2 - mod_cloudflare - apxs2 ] I have changed my nameservers to point to CloudFlare. The problem is that all the IP addresses are coming in as CloudFlare's. This is no good, because I have to monitor and block some specific traffic. mod_cloudflare is supposed to resolve this but I have been unable to get this installed. The command in the documentation uses apxs2. I can't figure out how to install this, or if it just means for 'apache 2.4'. I'm running 2.2.3, and I can use 'apxs'. When I run: apxs -aic mod_cloudflare.c I get the error apxs:Error: Command failed with rc=65536 Does this mean I need apxs2 or something else? How do I get mod_cloudflare working on my server? I appreciate any help, the documentation is vague and limited.

  Read the article

• Can Remote Desktop be set up to use IPv6?

  - by Garrett

  I have both a Windows 7 Ultimate and a Windows XP Professional machine set up on my home network. I would like to be able to access them from school. Port forwarding is not currently an option (long story). Is there a way to set it so that I can RDP (yes it has to be RDP not something like TeamViewer or LogMeIn) over IPv6, possibly using Teredo? I have tried but I can't seem to get it working. Also I cannot ping these machines' IPv6 addresses. How can I get this set up?

  Read the article

• Need help completing this Powershell script with some Exchange 2010 commands.

  - by Pure.Krome

  Hi folks. the following powershell script lists all the email aliases I have for a single mailbox. >$mbx = Get-Mailbox myuser >$mbx.EmailAddresses and that lists all the addresses. eg. SmtpAddress : [email protected] AddressString : [email protected] ProxyAddressString : smtp:[email protected] Prefix : SMTP IsPrimaryAddress : False PrefixString : smtp SmtpAddress : [email protected] AddressString : [email protected] ProxyAddressString : smtp:[email protected] Prefix : SMTP IsPrimaryAddress : False PrefixString : smtp SmtpAddress : [email protected] AddressString : [email protected] ProxyAddressString : SMTP:[email protected] Prefix : SMTP IsPrimaryAddress : True PrefixString : SMTP Now to add a new email address, I do the following poweshell command :- $mbx.EmailAddresses += "myEmailAddress.com" $mbx | Set-Mailbox So i'm not sure how i can use the foreach to remove each address? I tried:- @mbx.EmailAddresses | foreach { $mbx.EmailAddresses -= $._SmtpAddress } and that failed miserably. That's my first attempt of PS script, ever :P Can anyone help?

  Read the article

• IPv6 6to4 on Windows Server

  - by Graham Wager

  I'm looking for a relatively simple guide to setting up IPv6 properly on a home network. This network currently has a server (Windows Server 2008R2) running RRAS that establishes connectivity to the internet using a demand-dial PPPoE connection and handles the NAT. It also hosts a DNS server and DHCP. My ISP does not support IPv6, but I have a static IPv4 address. I've read about 6to4 and signed up at tunnelbroker.net, but quickly felt out of my depth. How do I configure my network to use it, and how I should configure my DHCP server with regards to IPv6 addresses?

  Read the article

• NAT and ISP Subnet when load balancing on pfsense?

  - by dannymcc

  I have a pfsense box that I'm trying to plan the configuration for. I am going to be load balancing two ISP's, each with their own /29 static IP subnet. The question I have is in relation to the way those IP's are associated with workstations on the local network. Currently I have some workstations with local (192.168.1.0/29) IP addresses, and other more complicated workstation setups have their own public IP address. Some of the more complicated systems have a NAT 1:1 configuration where I forward a public IP address to a local IP address. Others however are directly on the ISP subnet and cannot be seen on our local network. Is this configuration possible with pfsense? If so, what terms should I be looking through the documentation for? Here is a simple/brief diagram of what I am trying to achieve.

  Read the article

• How to route traffic through a specific SOCKS proxy on a per-app basis?

  - by GJ.

  I'm running a certain desktop app (actually via AIR if it makes any difference) which doesn't have any built-in proxy configuration settings. I need to get all traffic just from this app directed through a secure SOCKS proxy. This implies I can't use the global network preferences, as these would affect many other apps. Is there any way to force all network communication through a given SOCKS proxy on a per-app basis? It would also be helpful to know if there's a way to perform such routing globally, based on specific IP addresses (as this could allow for some reasonable workaround).

  Read the article

• Route an IP from WAN to a host on LAN on OpenWRT

  - by Zsub

  EDIT: I know how to use NAT, I specifically want the server to be reachable on two IP's, one private, one public, with the firewall of the OpenWRT in between, if feasible. At the office we have recieved a /29 from our ISP. The first address is reserved for their endpoint, so I'm free to use five addresses. We run a local network, so of course there is a router in between running OpenWRT to provide all hosts with (W)LAN (dhcp from a private range). However, we also have a server running OS X Server 10.6 (Snow Leopard) and I'd like that server to be accessible both from the LAN using a private IP as well as from the WAN on it's own public IP. Point of note is that the server only has one network port, so multiple NICs is not an option, unfortunately. How would I go about doing this?

  Read the article

• change email address format with minimal disruption

  - by femi

  Hello, all the email addresses in my organization are in the format [email protected]. this was started when we were a small organization. Now we have grown and need to use something a bit more professional like [email protected] how can this change be implemented with minimal disruption? We currently only use smarteremail. Could recieving ONLY with the old and replying with the new be a solution..till we wean our recipients off the old email address? Any suggestions are welcome. How will moving to exchange help in this instance? Can it be configured to automatically send out using a different address? Thanks

  Read the article

• D-Link DNS-323 NAS firmware update

  - by Mark Beaton

  Hi all, I've got a D-Link DNS-323 NAS enclosure holding a bunch of multimedia files that I've (possibly stupidly) just updated the firmware on, from 1.03 to 1.08. The updater indicated it applied the firmware patch successfully, but after rebooting it I can no longer get into it via the web interface, either via the static IP I had assigned it before the update, or by any of the DHCP-assigned addresses that I can see are currently assigned by my router. The unit just sits there, with the drives (2x512 set up as RAID-1) thrashing away seemingly forever... So, my question - has anyone had a similar experience with one of these units? Any advice etc? I've googled the hell out of it, and can't find anything useful.

  Read the article

• Disable IPv6 on Loopback address (Localhost, Computer name, ...)

  - by Greg Bray

  We tried installing a 3rd party software product on a new Windows 2008 R2 server and found that everything works except for accessing local services through loopback addresses such as localhost or the computer name (ex: VPS-Web which resolves to localhost). We are not using IPv6 and would like to disable it until the software is compatible. I tried using these instructions for disabling IPv6 on Windows 2008 R2 but it did not disable the protocol for localhost. Pinging localhost or VPS-Web will still return ::1: instead of 127.0.0.1. I can use ping localhost -4 to get the correct address, but IPv6 takes precedent over IPv4 so the 3rd party software only gets the IPv6 address.

  Read the article

• Exchange Server 2010 ActiveSync SSL Certificate Problem

  - by Cell-o

  Hi All, We have a problem related Exchange Server 2010 Activesync.My problem is;When I connecting to activesync from outside, I am receiving the following error. ExRCA is testing Exchange ActiveSync. The Exchange ActiveSync test failed. Test Steps Attempting to resolve the host name mail.xxxxx.com in DNS. The host name resolved successfully. Additional Details IP addresses returned: xx.0.x3.4 Testing TCP port 443 on host mail.x.com to ensure it's listening and open. The port was opened successfully. Testing the SSL certificate to make sure it's valid. The SSL certificate failed one or more certificate validation checks. Test Steps Validating the certificate name. Certificate name validation failed. Tell me more about this issue and how to resolve it Additional Details Host name mail.x.com doesn't match any name found on the server certificate CN=xxxxxx. Thanks in advance all your help.

  Read the article

• Mounting Gluster Volumes

  - by Roman Newaza

  I have created Hosted Zone with 2 IP addresses of Gluster Cluster, both IP are returned by dig. After mounting Gluster, I cannot ls mount point as it takes long time. mount shows me it's mounted, but df doesn't. Finally, I have this: ls: cannot access /mnt/storage: Transport endpoint is not connected. But if I mount it with the one of the IP, no problem - volume contents is accessible OS: Ubuntu 11.10 GlusterFS: 3.2.6 Log: http://pastie.org/private/2jgp4h1hnqgzych3djtg I have can telnet storage from client - ports are open.

  Read the article

• failed to use mutt to send mail to company mailbox

  - by Acewind

  I'm using mutt&postfix on CentOS 6.2: mutt-1.5.20-2.20091214hg736b6a.el6_1.1.x86_64 postfix-2.6.6-2.2.el6_1.x86_64 When I try to send mail to my company mailbox, I receive an error: mutt -s "test" [email protected] < /home/mail.txt error from postfix: : host out1.ourcompany.com[10.30.17.100] said: 555 Syntax error (in reply to MAIL FROM command) Then I try to use service sendmail as SMTP server, but also failed: **----- The following addresses had permanent fatal errors ----- (reason: 555 Syntax error) ----- Transcript of session follows ----- ... while talking to out1.ourcompany.com.: MAIL From: SIZE=667 <<< 555 Syntax error 554 5.0.0 Service unavailable** Any body can tell me why? Thanks!!!! I can make sure DNS is OK, and I set realname "root@myserver" in /etc/Muttrc

  Read the article

• How to send a batch file by email

  - by MikeL

  Trying to send a batch file as an email attachment, I get the following error: mx.google.com rejected your message to the following e-mail addresses: [email protected] mx.google.com gave this error: Our system detected an illegal attachment on your message. Please visit http://support.google.com/mail/bin/answer.py?answer=6590 to review our attachment guidelines. q42si10198525wei.6 Your message wasn't delivered because the recipient's e-mail provider rejected it. This also happens if I place the batch file in a .zip archive. I need to send a batch file to everyone at my company for them to run, preferably without having to change file extensions first. Is this possible by email?

  Read the article

• DNS problems on CentOS fresh install

  - by Rick Koshi

  I'm having some DNS issues on a new box I'm installing with CentOS 6.2. I am able to look up names using nslookup, dig, or host. I am able to ping machines by name or by IP address. However, when I try other tools, such as ssh, wget, or yum, they are unable to resolve names. For example: # wget http://www.google.com --2012-03-08 14:48:06-- http://www.google.com/ Resolving www.google.com... failed: Name or service not known. wget: unable to resolve host address `www.google.com' # ssh www.google.com ssh: Could not resolve hostname www.google.com: Name or service not known # ping -c 1 www.google.com PING www.l.google.com (74.125.113.106) 56(84) bytes of data. 64 bytes from vw-in-f106.1e100.net (74.125.113.106): icmp_seq=1 ttl=46 time=43.6 ms --- www.l.google.com ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 59ms rtt min/avg/max/mdev = 43.665/43.665/43.665/0.000 ms # host www.google.com www.google.com is an alias for www.l.google.com. www.l.google.com has address 74.125.113.99 www.l.google.com has address 74.125.113.103 www.l.google.com has address 74.125.113.104 www.l.google.com has address 74.125.113.105 www.l.google.com has address 74.125.113.106 www.l.google.com has address 74.125.113.147 My /etc/nsswitch.conf file is the default, including this (standard) line: hosts: files dns /etc/resolv.conf is as set up by DHCP: ; generated by /sbin/dhclient-script nameserver 192.168.1.254 192.168.1.254 is a working DNS server (my DSL modem, working for years with other machines) Anyone know why ping would work, but ssh/wget would fail? Per NcA's suggestion, I tried changing /etc/resolv.conf to point to 8.8.8.8. Oddly enough, this does make it work. Obviously, my DSL modem is responding to DNS requests in some way that some parts of Linux's resolution system don't like. Looking at the tcpdump, I am unable to see what the difference is. Certainly, both servers are sending the same addresses. Here's the output from tcpdump -nn -X with the server set to the DNS server on the DSL modem. It's clearly replying with the correct addresses, but ssh/wget don't seem happy with it for some reason: 15:53:52.133580 IP 192.168.1.254.53 > 192.168.1.2.54836: 33157 7/0/0 CNAME www.l.google.com., A 74.125.115.105, A 74.125.115.106, A 74.125.115.147, A 74.125.115.99, A 74.125.115.103, A 74.125.115.104 (148) 0x0000: 4500 00b0 e33a 0000 ff11 53b1 c0a8 01fe E....:....S..... 0x0010: c0a8 0102 0035 d634 009c 7528 8185 8180 .....5.4..u(.... 0x0020: 0001 0007 0000 0000 0377 7777 0667 6f6f .........www.goo 0x0030: 676c 6503 636f 6d00 0001 0001 c00c 0005 gle.com......... 0x0040: 0001 0007 acd0 0008 0377 7777 016c c010 .........www.l.. 0x0050: c02c 0001 0001 0000 0001 0004 4a7d 7369 .,..........J}si 0x0060: c02c 0001 0001 0000 0001 0004 4a7d 736a .,..........J}sj 0x0070: c02c 0001 0001 0000 0001 0004 4a7d 7393 .,..........J}s. 0x0080: c02c 0001 0001 0000 0001 0004 4a7d 7363 .,..........J}sc 0x0090: c02c 0001 0001 0000 0001 0004 4a7d 7367 .,..........J}sg 0x00a0: c02c 0001 0001 0000 0001 0004 4a7d 7368 .,..........J}sh 15:53:52.135669 IP 192.168.1.254.53 > 192.168.1.2.54836: 65062- 0/0/0 (32) 0x0000: 4500 003c e33b 0000 ff11 5424 c0a8 01fe E..<.;....T$.... 0x0010: c0a8 0102 0035 d634 0028 98f9 fe26 8000 .....5.4.(...&.. 0x0020: 0001 0000 0000 0000 0377 7777 0667 6f6f .........www.goo 0x0030: 676c 6503 636f 6d00 001c 0001 gle.com..... I'm not enough of an expert to know if this is malformed in some way, but ping seems to do the right thing with it. For comparison, here's the same thing when querying 8.8.8.8: 15:57:27.990270 IP 8.8.8.8.53 > 192.168.1.2.49028: 59114 7/0/0 CNAME www.l.google.com., A 74.125.113.105, A 74.125.113.103, A 74.125.113.106, A 74.125.113.147, A 74.125.113.104, A 74.125.113.99 (148) 0x0000: 4500 00b0 5530 0000 2f11 6453 0808 0808 E...U0../.dS.... 0x0010: c0a8 0102 0035 bf84 009c 39f8 e6ea 8180 .....5....9..... 0x0020: 0001 0007 0000 0000 0377 7777 0667 6f6f .........www.goo 0x0030: 676c 6503 636f 6d00 0001 0001 c00c 0005 gle.com......... 0x0040: 0001 0001 516a 0008 0377 7777 016c c010 ....Qj...www.l.. 0x0050: c02c 0001 0001 0000 0116 0004 4a7d 7169 .,..........J}qi 0x0060: c02c 0001 0001 0000 0116 0004 4a7d 7167 .,..........J}qg 0x0070: c02c 0001 0001 0000 0116 0004 4a7d 716a .,..........J}qj 0x0080: c02c 0001 0001 0000 0116 0004 4a7d 7193 .,..........J}q. 0x0090: c02c 0001 0001 0000 0116 0004 4a7d 7168 .,..........J}qh 0x00a0: c02c 0001 0001 0000 0116 0004 4a7d 7163 .,..........J}qc 15:57:28.018909 IP 8.8.8.8.53 > 192.168.1.2.49028: 31984 1/1/0 CNAME www.l.google.com. (102) 0x0000: 4500 0082 7b1b 0000 2f11 3e96 0808 0808 E...{.../.>..... 0x0010: c0a8 0102 0035 bf84 006e c67e 7cf0 8180 .....5...n.~|... 0x0020: 0001 0001 0001 0000 0377 7777 0667 6f6f .........www.goo 0x0030: 676c 6503 636f 6d00 001c 0001 c00c 0005 gle.com......... 0x0040: 0001 0001 517f 0008 0377 7777 016c c010 ....Q....www.l.. 0x0050: c030 0006 0001 0000 0258 0026 036e 7334 .0.......X.&.ns4 0x0060: c010 0964 6e73 2d61 646d 696e c010 0016 ...dns-admin.... 0x0070: 91f3 0000 0384 0000 0384 0000 0708 0000 ................ 0x0080: 003c .< I still don't know why the server's reply is adequate for ping but not for ssh/wget. If anyone has ideas, I'd be happy to hear them. For now, though, I can either refer to an outside DNS server or set up my own server on the new box. It's a workaround that seems like it should be unnecessary, but will allow me to proceed.

  Read the article

• How do I make a virtualised WAN?

  - by EnchantedEggs

  I want to create a virtualised WAN. As in, I want to have a couple of VMs (VBox) on one physical host machine, that exist on separate LANs, but that can talk to each other. Do I make the VMs, set them up with different IP addresses (e.g. 1.2.3.4 and 5.6.7.8) and then configure port forwarding between them somehow??? I've seen articles that set up port forwarding on port 2222, but I don't really understand why this works. How is setting up the VM to listen to port 2222 and then port forward from there to, say, port 80, any different from just telling the VM to listen on port 80 in the first place? FYI, the VMs run Ubuntu Desktop 14.x.

  Read the article

• lots of dns requests from China, should I worry?

  - by nn4l

  I have turned on dns query logs, and when running "tail -f /var/log/syslog" I see that I get hundreds of identical requests from a single ip address: Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#10856: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#44334: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#15268: query: mydomain.de IN ANY + Apr 7 12:36:13 server17 named[26294]: client 121.12.173.191#59597: query: mydomain.de IN ANY + The frequency is about 5 - 10 requests per second, going on for about a minute. After that the same effect repeats from a different IP address. I have now logged about 10000 requests from about 25 ip addresses within just a couple of hours, all of them come from China according to "whois [ipaddr]". What is going on here? Is my name server under attack? Can I do something about this?

  Read the article

• What settings need to be changed to allow EC2 instances to use Amazon's Route 53 for DNS?

  - by ks78

  I have a number of Amazon EC2 instances, all running Ubuntu, which I'd like to configure to use Amazon's Route 53. I setup a script, following Shlomo Swidler's article, but ran into script-related issues, which were answered here. Now, I have the script working, but my instances are still not able to access Route 53's DNS. By this I mean, they are not able to resolve hostnames to IP addresses. My instances are currently configured with the DNS server IP address Amazon pushes out to them by default, does that need to be changed when using Route 53? I'm also IP-restricting my instances using the Security Groups. Could that be the problem? Is there a certain IP address or port I should open to allow communication with Route 53? It seems that DNS requests should be originating from my instances so the Security Groups shouldn't be an issue, but I've been wrong before. If anyone has any ideas, I'd really appreciate it.

  Read the article

< Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79  | Next Page >