Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 72/343 | < Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79  | Next Page >

• How do I install drivers for the Atheros AR8161 Ethernet controller?

  - by Jessica Burnett

  I have installed Ubuntu 12.04-64 bit on my Lenovo IdeaPad laptop, and the wired Ethernet (LAN) connection doesn't work. Running the lspci -vv | grep Atheros command from the terminal shows me I have the AR8161 Gigabit Ethernet controller: 02:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 08) This looks like a new product whose drivers are not built into Ubuntu. How do I install drivers to get the AR8161 working?

  Read the article

• Atheros AR8132 Ethernet refuses to connect after suspend

  - by Ramesh Patel

  I'm having an issue where my ethernet card (Atheros Communications Inc. AR8132 Fast Ethernet (rev c0)) refuses to recognize when a network cable is plugged in after a suspend. This is dmesg after suspending: [135897.712049] atl1c 0000:02:00.0: MAC state machine can't be idle since disabled for 10ms second [135897.743729] ADDRCONF(NETDEV_UP): eth0: link is not ready [135898.541804] ADDRCONF(NETDEV_UP): eth1: link is not ready [135900.452077] atl1c 0000:02:00.0: irq 47 for MSI/MSI-X [135900.672262] atl1c 0000:02:00.0: Error get phy ID [135900.673060] ADDRCONF(NETDEV_UP): eth0: link is not ready [135900.674140] ADDRCONF(NETDEV_UP): eth0: link is not ready [135925.604052] [135935.776051] eth1: no IPv6 routers present eth0 is the ethernet card and eth1 is the wlan card (Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)). The ethernet card uses the atl1c driver and the wlan card uses the wl driver. Sorry, should have mentioned as well, running Ubuntu 12.04 with kernel 3.2.0-25-generic.

  Read the article

• Resetting network adapter?

  - by Quixo

  I'm running Ubuntu 12.04. I get a strong wireless signal throughout my house, and the wireless symbol in the upper-right-hand corner shows that it's connected. The problem is, occasionally I am unable to access the internet (still having a strong symbol). This happened with Windows 7, too, but running the network troubleshooter fixed it each time. It claimed to be "resetting the network adapter". So, what I need to know is: How do I replicate that process on Ubuntu? Thanks for your help!

  Read the article

• Nice network diagram editor?

  - by Nicolas Raoul

  Writing a commercial proposal, I want to create a nice graphic showing the clients the architecture I thought of for their IT network, with servers, network connections, firewall, load-balancing, etc. For years I have been using dia, but I am tired of it because: the results are not satisfying, very few network elements are available, and each element's graphic representation is really ugly. Question: How to create nice network diagrams? If a better set of elements was available for dia, that would be a solution.

  Read the article

• Can't get bonding and bridging to work for KVM

  - by user9546

  Hi everyone. I can't for the life of me get bonding and bridging to work for the KVM setup I'm building. I'm using a fresh install (not an upgrade) of Ubuntu Server 10.10. I have 4 NICs on the same subnet (two intended for each of my two VMs). I'm trying to achieve the setup that Uthark describes here. But following his guidelines didn't work for me. My eth0 and eth1 did not come up, and "brctl show" showed that br0 didn't have any interfaces (the bond). I assumed it didn't work because he's using 10.4, and this article says there's a recent change in bonding: [I can't post more than one hyperlink per post because I'm a newbie.] I had to use this article to get my interfaces to work at all on the same subnet, which is why I have the post-up lines on some of my interfaces: [I can't post more than one hyperlink per post because I'm a newbie.] I installed ifenslave and ethtool. I also created /etc/modprobe.d/aliases.conf with the following content: alias bond0 bonding options bonding mode=6 miimon=100 downdelay=200 updelay=200 And I included "bonding" in /etc/modules So, after several approaches, here is my latest interfaces file: auto lo iface lo inet loopback auto eth5 iface eth5 inet manual auto br5 iface br5 inet static post-up /sbin/ip rule add from [network].79 lookup 10 post-up /sbin/ip route add table 10 default via [network].1 src [network].79 dev br5 address [network].79 netmask 255.255.255.0 network [network].0 broadcast [network].255 gateway [network].1 bridge_ports eth5 bridge_stp off bridge_fd 0 bridge_maxwait 0 auto eth2 iface eth2 inet manual auto br2 iface br2 inet static post-up /sbin/ip rule add from [network].78 lookup 11 post-up /sbin/ip route add table 11 default via [network].1 src [network].78 dev br2 address [network].78 netmask 255.255.255.0 network [network].0 broadcast [network].255 gateway [network].1 bridge_ports eth2 bridge_stp off bridge_fd 0 bridge_maxwait 0 iface eth0 inet manual iface eth1 inet manual auto bond0 iface bond0 inet static bond_miimon 100 bond_mode balance-alb up /sbin/ifenslave bond0 eth0 eth1 down /sbin/ifenslave -d bond0 eth0 eth1 auto br0 iface br0 inet static address [network].60 netmask 255.255.255.0 network [network].0 broadcast [network].255 gateway [network].1 bridge_ports bond0 eth2, eth5, br2, and br5 all seem to be working fine. The only other thing I could find that looked suspicious is an error regarding bonding in /var/log/messages: kernel: [ 3.828684] bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. even though there is a bond-miimon line in /etc/network/interfaces (if that's what they're talking about). Also, the bond seems to go in and out of promiscuous mode several times on boot: Jan 20 14:19:02 kvmhost kernel: [ 3.902378] device bond0 entered promiscuous mode Jan 20 14:19:02 kvmhost kernel: [ 3.902390] device bond0 left promiscuous mode Jan 20 14:19:02 kvmhost kernel: [ 3.902393] device bond0 entered promiscuous mode Jan 20 14:19:02 kvmhost kernel: [ 3.902397] device bond0 left promiscuous mode Jan 20 14:19:03 kvmhost kernel: [ 4.998990] device bond0 entered promiscuous mode Jan 20 14:19:03 kvmhost kernel: [ 4.999005] device bond0 left promiscuous mode Jan 20 14:19:03 kvmhost kernel: [ 4.999008] device bond0 entered promiscuous mode Jan 20 14:19:03 kvmhost kernel: [ 4.999012] device bond0 left promiscuous mode Any advice would be greatly appreciated. It seems that this must be possible, based on other posts, but I can't see what I'm doing wrong. Thanks.

  Read the article

• How to send packets via a pptp vpn tunnel?

  - by Phill

  I'm trying to send certain port traffic through my ppp0 interface it's a pptp vpn tunnel, First, I'm using a wireless usb interface, I connect up to my access point, then I initiate my vpn, there is a connection but I do not channel all connexions through that, nor do I want to, so, say I want to channel all port 80 packets through my vpn (interface dev ppp0). I first run: iptables -t mangle -A OUTPUT -p tcp --dport 80 -j MARK --set-mark 0xa to mark the correct packets then I add a table named vpn_table, I then add ip route add default dev ppp0 table vpn_table when I do that traffic begins to dribble through the ppp0, but no pages load. I supose I must have caused some sort of coflict, or the route I'm adding in vpn_table isn't quite right. I'm not sure, I think I'm marking the packets correctly but I can't be sure of that either. UPDATE: I think i've got part of the issue solved: running tcpdump -i ppp0 showed me that indeed there was outgoing requests via ppp0, now, there is never a response, and pages do not load with using that interface..i'm still missing something.

  Read the article

• Wireless shows up as disabled, how can I get it working?

  - by Lazer

  $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

  Read the article

• Log incoming requests

  - by Maxim Eliseev

  We have Tomcat running on Ubuntu server. It runs a web service, open to the internet. Sometimes it has sudden spike of traffic and goes down. There is nothing unusual in Tomcat access logs. I guess because some of the requests are so 'heavy' that they never finish and hence are not recorded to Tomcat access logs. Is there a way to configure Ubuntu to log incoming requests in the following format (below)? Date, Time, URL (with query string params), IP address (of client) There should be one line per request. Each request should be logged before it is executed. Only incoming requests to ports 80 and 443 should be logged.

  Read the article

• Mirroring Ubuntu on several systems in a computer lab

  - by Harvey Steck

  I am working in a new refugee school where the only Internet service available is a slow satellite connection. We are about to set up a computer lab (already have desktop systems and am about to install Ubuntu on them). I'm a newbie when it comes to Linux, but it seems a better alternative than pirated copies of Windows. I'd like to set up one Ubuntu system, and then mirror that system on perhaps ten to twenty other systems (all of which would be on an ethernet network). I expect to have an internet connection on the one system that I set up, but then it may be difficult to have enough bandwidth to go through all the same steps on the other ten systems. Can I set up the other ten or twenty computers to get all of their updates/upgrades/configuration from one master system? Can I also set things up so that students cannot change the configuration, install new programs, etc.? Appreciate any help you can give. -- Harvey

  Read the article

• Can't get HP Officejet 6500 card reader to work.

  - by Dennis

  This network (wired) printer works great using the latest HPLIP drivers. However when I plug in an SD card, it just blinks and never shows up mounted anywhere. Has anyone come up with a way to mount these? I'm using Lucid, 10.04. re: version, hp-info says xxxxx@lucid:~$ hp-info HP Linux Imaging and Printing System (ver. 3.10.5) Device Information Utility ver. 5.2 Copyright (c) 2001-9 Hewlett-Packard Development Company, LP This software comes with ABSOLUTELY NO WARRANTY. This is free software, and you are welcome to distribute it under certain conditions. See COPYING file for more details. Using device: hp:/net/Officejet_6500_E709a?zc=HP05857E

  Read the article

• How do I get network working on a Dell n5010 - Ubuntu 10.04

  - by cyberroger

  Hey. I just formatted a Dell n5010 and installed Ubuntu 10.04. Now,when i try to access the Internet it doesn't find the available networks. Informations about it: My network is set to broadcast SSID; Already typed lspci, and it doesnt returns my wireless card; Tried installing windows drivers from fabricant cd usind diswrapper, but it says it cant complete the installation because it cant find some "Device" folder; I don't know what else to do, I switch the wireless button on/off and it just can't see any wireless connection, includin mine. Here are the informations about lspci: *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fbc00000-fbc03fff And this: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 12:00.0 Network controller: Broadcom Corporation Device 4727 (rev 01) 13:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) Thanks!

  Read the article

• make my Ubuntu 12.04 laptop visible on the network

  - by Andrew Boyd

  I'm ecstatically happy with my 12.04 on my laptop after loading it over my MS Vista... but there's just one thing, one little fly in the ointment.... While I can view our 2 Terabyte, shared hard-drive in the lounge (and copy files back and forth) I can't see my PC (when I boot up in Ubuntu 12.04) nor the Lubuntu computer connected to the TV (for movies, Youtube etc). Printing to the HP office jet on the PC doesnt work over the network either. Have had one dubious flirtation with Samba, which seems to be the only thing I've found that will 'work', however halfway through that "installation" everything just ground to a halt, the directions began to stop making sense... I was working from this page. Our Network consists of the following: Our Internet service is wirelessly sent to us from our provider to our dish on a pole. It comes into the house via an ethernet cable. We split it there to a phone, and to 6 other destinations (bedrooms, computers, and to another splitter in the lounge which has a wifi antennae and 4 ethernet ports). one port goes to the Lubuntu OS PC which is connected to the TV the second port goes to the 2 Terabyte harddrive (MS powered 'Mybooklive') (the other two are empty) My Ubuntu 12.04 laptop connects wirelessly to this splitter in the lounge. I know just enough about computers to get myself into an awful mess without too much trouble We usually can view friends' laptops when they get on our network (as they are invariably MS OS's) Our flatmate, who introduced us to Linux's computer is also invisible How can we make our Linux OS based computers visible on the network and share files and printing?

  Read the article

• Unable to set default gateway

  - by GrandMasterFlush

  I'm running Ubuntu server via Hyper-V and have successfully installed it but seem unable to ping the server or ping any other machines on the network from the server. After doing a bit of reading I've noticed that the default gateway isn't set but when I try and set it I keep getting error messages which I can't understand. From this article I've tried ip route add default via 10.0.10.200 Which reports: RTNETLINK answers: Operation not permitted If I try running it prefixed with sudo but it reports: `RNETLINK answers: No such process I've editted /etc/network/interfaces but when I start the machine and type netstat -nr there is nothing listed. Can anyone tell me where I'm going wrong please? EDIT : /etc/network/interfaces contains: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp

  Read the article

• IPSec Offload support in 82576GB controller for Linux

  - by Rodrigo Leal

  Due to migration of servers to cloud computing, we bought several NICs that support mechanisms like SRIOV and VMDQ. Furthermore, as security risk was also a concern and we did not want to create more overhead on the processor, IPSec Offload support was essential. The model chosen was: Intel Gigabit ET2 Quad Port Svr Adptr. (With 82576GB controller): http://ark.intel.com/products/49187/intel-gigabit-et2-quad-port-server-adapter However, we were unable to configure IPSec Offload on Linux. We tried to test on another server we have, a Windows Server 2012 R2, but again without success. It seems that the driver for this controller is not available for windows server 2012 R2, and Linux. The test on windows would be only for verification purposes, we will not use this platform. Could someone confirm this lack of support for Linux?

  Read the article

• How do I efficiently code both the client and server at the same time?

  - by liamzebedee

  I'm coding my game using a client-server model. When playing on singleplayer, the game starts a local server, and interacts with it just like a remote server (multiplayer). I have done this to avoid coding separate singleplayer and multiplayer code. I have just started coding and have encountered a major problem. Currently I'm developing the game in Eclipse, having all the game classes organized into packages. Then, in my server code, I just use all the classes in the client packages. The problem is, these client classes have variables that are specific to rendering, which obviously wouldn't be performed on a server. Should I create modified versions of the client classes to use in the server? Or should I just modify the client classes with a boolean, to indicate if its the client/server using it. Are there any other options I have? I just had a thought about maybe using the server class as the core class, then extending it with rendering stuff?

  Read the article

• What Keeps You from Changing Your Public IP Address and Wreaking Havoc on the Internet?

  - by Jason Fitzpatrick

  What exactly is preventing you (or anyone else) from changing their IP address and causing all sorts of headaches for ISPs and other Internet users? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader Whitemage is curious about what’s preventing him from wantonly changing his IP address and causing trouble: An interesting question was asked of me and I did not know what to answer. So I’ll ask here. Let’s say I subscribed to an ISP and I’m using cable internet access. The ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let’s say, 60.61.62.75, and messing with another consumer’s internet access? For the sake of this argument, let’s say that this other IP address is also owned by the same ISP. Also, let’s assume that it’s possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gateway, a network address and a broadcast address. So that’s 3 addresses the ISP “loses” to you. That seems very wasteful for dynamically assigned IP addresses, which the majority of customers are. Could they simply be using static arps? ACLs? Other simple mechanisms? Two things to investigate here, why can’t we just go around changing our addresses, and is the assignment process as wasteful as it seems? The Answer SuperUser contributor Moses offers some insight: Cable modems aren’t like your home router (ie. they don’t have a web interface with simple point-and-click buttons that any kid can “hack” into). Cable modems are “looked up” and located by their MAC address by the ISP, and are typically accessed by technicians using proprietary software that only they have access to, that only runs on their servers, and therefore can’t really be stolen. Cable modems also authenticate and cross-check settings with the ISPs servers. The server has to tell the modem whether it’s settings (and location on the cable network) are valid, and simply sets it to what the ISP has it set it for (bandwidth, DHCP allocations, etc). For instance, when you tell your ISP “I would like a static IP, please.”, they allocate one to the modem through their servers, and the modem allows you to use that IP. Same with bandwidth changes, for instance. To do what you are suggesting, you would likely have to break into the servers at the ISP and change what it has set up for your modem. Could they simply be using static arps? ACLs? Other simple mechanisms? Every ISP is different, both in practice and how close they are with the larger network that is providing service to them. Depending on those factors, they could be using a combination of ACL and static ARP. It also depends on the technology in the cable network itself. The ISP I worked for used some form of ACL, but that knowledge was a little beyond my paygrade. I only got to work with the technician’s interface and do routine maintenance and service changes. What keeps me from changing this IP address to, let’s say, 60.61.62.75 and mess with another consumer’s internet access? Given the above, what keeps you from changing your IP to one that your ISP hasn’t specifically given to you is a server that is instructing your modem what it can and can’t do. Even if you somehow broke into the modem, if 60.61.62.75 is already allocated to another customer, then the server will simply tell your modem that it can’t have it. David Schwartz offers some additional insight with a link to a white paper for the really curious: Most modern ISPs (last 13 years or so) will not accept traffic from a customer connection with a source IP address they would not route to that customer were it the destination IP address. This is called “reverse path forwarding”. See BCP 38. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

  Read the article

• Authenticate to VM using vagrant up

  - by utrecht

  Authentication failure during Vagrant Up, while vagrant ssh and ssh vagrant@localhost -p2222 works I would like to execute a shell script using Vagrant at boot. Vagrant is unable to Authenticate, while the VM has been started using vagrant up: c:\temp\helloworld>vagrant up Bringing machine 'default' up with 'virtualbox' provider... ==> default: Importing base box 'helloworld'... ==> default: Matching MAC address for NAT networking... ==> default: Setting the name of the VM: helloworld_default_1398419922203_60603 ==> default: Clearing any previously set network interfaces... ==> default: Preparing network interfaces based on configuration... default: Adapter 1: nat ==> default: Forwarding ports... default: 22 => 2222 (adapter 1) ==> default: Booting VM... ==> default: Waiting for machine to boot. This may take a few minutes... default: SSH address: 127.0.0.1:2222 default: SSH username: vagrant default: SSH auth method: private key default: Error: Connection timeout. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... ... After executing CTRL + C it is possible to authenticate to the VM using vagrant ssh and ssh vagrant@localhost -p2222 Vagrant file I use the default Vagrantfile and I only changed the hostname: # -*- mode: ruby -*- # vi: set ft=ruby : # Vagrantfile API/syntax version. Don't touch unless you know what you're doing! VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| # All Vagrant configuration is done here. The most common configuration # options are documented and commented below. For a complete reference, # please see the online documentation at vagrantup.com. # Every Vagrant virtual environment requires a box to build off of. config.vm.box = "helloworld" ... Vagrant version c:\temp\helloworld>vagrant --version Vagrant 1.5.1 Question How to authenticate to VM using vagrant up?

  Read the article

• Suspending my laptop breaks ethernet over firewire, are there commands which can fix it?

  - by Josh

  As mentioned in this question I am using a firewire cable to provide a private network between my laptop and my desktop, because it makes using the screen sharing program synergy much nicer than using WIFI. However when I leave my office for the day and I suspend my laptop, when I return the next day, the desktop and the laptop cannot communicate over firewire anymore. The firewire0 device still has an IP address. but when I try and ping the desktop I get no route to host I'm using kernel 2.6.35-24-generic #42-Ubuntu SMP x86_64 on Ubuntu 10.10. Is there some way I can remedy this without a reboot? Like, removing some kernel modules and re-inserting them? Here's what I have tried so far and the results: root@token:~# dmesg|tail -n 1 [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 root@token:~# modprobe -r firewire_net firewire_ohci firewire_core root@token:~# modprobe -v firewire_ohci insmod /lib/modules/2.6.35-24-generic/kernel/lib/crc-itu-t.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-core.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-ohci.ko root@token:~# dmesg|tail [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592563.410868] firewire_ohci: Removed fw-ohci device. [592579.160086] firewire_ohci: Added fw-ohci device 0000:02:00.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2 [592579.160137] firewire_ohci: isochronous cycle inconsistent [592579.660294] firewire_core: created device fw0: GUID 0000000000000000, S400 [592579.663805] firewire_core: created device fw1: GUID 0017f2fffe89bce6, S400 [592579.663813] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700720] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700842] firewire_core: refreshed device fw0 [592579.702603] firewire_net: firewire0: IPv4 over FireWire on device 0000000000000000 root@token:~# ping stan.firewire PING stan.firewire (192.168.100.1) 56(84) bytes of data. From token.local (192.168.100.3) icmp_seq=1 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=2 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=3 Destination Host Unreachable I also tried removing the modules prior to suspending, and re-inserting after resuming. This did not work either :-(

  Read the article

• How do I prevent missing network from slowing down boot-up?

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• Aser Aspire 3690 WIreless Not working, new Ubuntu user

  - by drew

  I don't know that much about Ubuntu, but I put it on an Acer Aspire 3690 Laptop (replaced Win Vista). Everything seems to work fine, but the wireless connection. It says "FIRMWARE MISSING". It detects that I have a wireless card, so I don't know what to do. I've already used the "ADDITIONAL DRIVERS" thing, and that didn't work. I've googled and have not found anything helpful. I don't really know what I'm doing, so can your directions please be kindergarden level? Thank you very much for any help you can provide. I really appreciate it.

  Read the article

• Can not connect to wireless on 12.04 with Intel WiFi Link 5100

  - by WiData

  I am having problem in connecting to wifi. I have dual boot (Windows 7 and Ubuntu 12.04) on my Dell Studio 15. I upgraded to 12.04 quite some time ago (at least one month) from 11.10. Everything was working fine till yesterday. Since yesterday I can see the list of available Wifi connection but does not connect to any or if connects (after hours of trying) then disconnects after few minutes. My wifi interface is Intel WiFi Link 5100 AGN. However the problem is on both Windows and Ubuntu. Here are outputs of some commands which may be useful for those interested in helping: ~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:22:19:fa:65:bb UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:794 errors:0 dropped:0 overruns:0 frame:0 TX packets:794 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:56280 (56.2 KB) TX bytes:56280 (56.2 KB) wlan0 Link encap:Ethernet HWaddr 00:22:fb:d2:fc:ce UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:239 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:53603 (53.6 KB) Here is the output for the command sudo lshw -C network *-network description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fb:d2:fc:ce width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-48-generic-pae firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:f8000000-f8001fff My kernel version is kernel version 3.2.0-48-generic-pae I also checked this post which was helpful. But I am not sure if what is the exact problem. Any suggestions will be helpful. Should I be changing the firmware/driver? Currently my /lib/firmware has following iwlwifi files /lib/firmware/iwlwifi-1000-5.ucode /lib/firmware/iwlwifi-5000-5.ucode /lib/firmware/iwlwifi-100-5.ucode /lib/firmware/iwlwifi-5150-2.ucode /lib/firmware/iwlwifi-105-6.ucode /lib/firmware/iwlwifi-6000-4.ucode /lib/firmware/iwlwifi-135-6.ucode /lib/firmware/iwlwifi-6000g2a-5.ucode /lib/firmware/iwlwifi-2000-6.ucode /lib/firmware/iwlwifi-6000g2a-6.ucode /lib/firmware/iwlwifi-2030-6.ucode /lib/firmware/iwlwifi-6000g2b-6.ucode /lib/firmware/iwlwifi-3945-2.ucode /lib/firmware/iwlwifi-6050-5.ucode /lib/firmware/iwlwifi-4965-2.ucode Thanks a lot for the help.

  Read the article

• Wireless not detected on an hp Pavilion g6

  - by Earl Larson

  I just bought an HP Pavilion g6 laptop and I installed Natty Narwhal alongside Windows 7. In Windows 7, my WiFi works perfect but in Ubuntu it absolutely (no matter what I do) won't detect my home WiFi network. Here is the output of "lspci": earl@ubuntu:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200] 01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 03:00.0 Network controller: Ralink corp. Device 5390 04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01) earl@ubuntu:~$

  Read the article

• Pluscom MAC address shows up but "wireless unavailable"

  - by Luigi

  I've got a pluscom pci card plugged into my desktop and although the mac address shows up in network manager, it says "Wireless unavailable". I'm using Ubuntu 12.10 Gnome Shell Remix... edgar@edgarQuantal:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off edgar@edgarQuantal:~$ ifconfig eth0 Link encap:Ethernet HWaddr 6c:f0:49:02:1f:b8 inet addr:192.168.0.7 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fe02:1fb8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1425 errors:0 dropped:0 overruns:0 frame:0 TX packets:1393 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:995753 (995.7 KB) TX bytes:134079 (134.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:363 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:40828 (40.8 KB) TX bytes:40828 (40.8 KB) It looks the same as the problem as here, seems quite complicated: http://ubuntuforums.org/showthread.php?t=1993226 Tried downloading the driver but i get this: "Unpacking firmware-ralink (from .../firmware-ralink_0.36_all.deb) ... dpkg: error processing /home/edgar/Downloads/firmware-ralink_0.36_all.deb (--install): trying to overwrite '/lib/firmware/rt2870.bin', which is also in package linux-firmware 1.95"

  Read the article

• Client side latency when using prediction

  - by Tips48

  I've implemented Client-Side prediction into my game, where when input is received by the client, it first sends it to the server and then acts upon it just as the server will, to reduce the appearance of lag. The problem is, the server is authoritative, so when the server sends back the position of the Entity to the client, it undo's the effect of the interpolation and creates a rubber-banding effect. For example: Client sends input to server - Client reacts on input - Server receives and reacts on input - Server sends back response - Client reaction is undone due to latency between server and client To solve this, I've decided to store the game state and input every tick in the client, and then when I receive a packet from the server, get the game state from when the packet was sent and simulate the game up to the current point. My questions: Won't this cause lag? If I'm receiving 20/30 EntityPositionPackets a second, that means I have to run 20-30 simulations of the game state. How do I sync the client and server tick? Currently, I'm sending the milli-second the packet was sent by the server, but I think it's adding too much complexity instead of just sending the tick. The problem with converting it to sending the tick is that I have no guarantee that the client and server are ticking at the same rate, for example if the client is an old-end PC.

  Read the article

• Slow DNS Resolution

  - by user4541

  After a clean install of 10.10 I'm finding DNS resolution takes quite a long time. Hitting any url takes a good few seconds (10 - 30) before the site is displayed. I'm thinking this is a DNS resolution issue due to the 'waiting' or 'looking up' text being displayed in Firefox and Chrome. I do not get this issue with Slackware Linux or Windows 7 so it is not network or DNS server specific issue. It's something on the client side. Looking around on Google I see there are a few other people with this issue. The ones that have reported a workaround by switching to openDNS are disabling IPV6 or dealing with another issue. Any help would be appreciated. My network card is wired: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express Thanks

  Read the article

< Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79  | Next Page >