Search Results

Search found 20285 results on 812 pages for 'selling software'.

Page 720/812 | < Previous Page | 716 717 718 719 720 721 722 723 724 725 726 727  | Next Page >

• Dead Linux server - need help and options

  - by Choi S.

  All, I have a Dell PE 1950 w/ 2 SATA drives in a software RAID1. OS is CentOS 5.5 (2.6.18.x). Starting this afternoon we received HW errors (something on the bus is bad, E171F) and the machine became unresponsive. We hard booted and it came back up for about 5 hours but then it happened again. I'm trying to figure out our options. Unfortunately we do not have similar hardware but I have a small desktop that I can use. I was contemplating putting one of the drives into the desktop and then starting it up. My goal was to then P2V it using Vmware converter but apparently the free v5.x doesn't support hot cloning/converting on a RAID volume, only the Enterprise 4.x version of Converter does. My questions are: 1.) Is putting a single drive out of a RAID1 pair into another piece of HW is safe? Based on my research and understanding it appears to be but would like confirmation. 2.) Is there any work around to the Vmware Converter not supporting RAID volumes during a hot clone/convert session? 3.) Are there other options I'm overlooking? Thanks in advance for reading and responding. --Choi S.

  Read the article

• VM load and ping problems after replacing server motherboard

  - by Andre

  Recently, we had to replace the motherboard of one of our servers. The procedure was done by IBM as it had guarantee. The server runs ESXi 5.1, with several virtual machines, including our main mail server (Domino) and a file server. After the replacing the motherboard and staring the VMs, ESXi asked us if we had moved it or copied (different motherboard is like a different computer). We clicked the latter. We started each machine and after some basic reconfiguration, all of them were up. However, we have been having problems with the mail server, it has been acting really slow at times (this could be when it syncs with the secondary mail server) and we have been checking with Centreon (a Nagios frontend) that its CPU load has been a bit high at times and ping response too. There was a moment this morning in which I tried connecting via SSH console and it was really slow to show login and basic commands like ifconfig and top. This particular mail server is a CentOS 4.4.7 64-bit. The little configuring we had to do after restarting it was to configure the network connection as it was resolving through DHCP. Our mail software is Lotus Notes server 9. Do you know of any way in which this replacement may be causing these difficulties, and how to fix it? Thanks.

  Read the article

• Nginx + PHPBB3 reverse proxy images problem

  - by siberiano

  Hello all I have a problem with my Nginx Frontend + Apache2 backend + PHPBB3 software. It doesn't load the CSS and the images neither. I get constant errors like these: 2010/04/14 16:57:25 [error] 13365#0: *69 open() "/var/www/foo/styles/styles/coffee_time/theme/large.css" failed (2: No such file or directory), client: 83.44.175.237, server: www.foo.com, request: "GET /styles/coffee_time/theme/large.css HTTP/1.1", host: "www.foo.com", referrer: "http://www.foo.com/viewforum.php?f=43" This is my config of the site: server { listen 80; server_name www.foo.com; access_log /var/log/nginx/foo.access.log; # serve static files directly location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico)$ { access_log off; expires 30d; root /var/www/trasteando/; } location / { root /var/www/foo/; index /var/www/foo/index.php; } # proxy the PHP scripts to predefined upstream .apache. # location ~ .php$ { proxy_pass http://apache; } location /styles/ { root /var/www/foo/styles/; }

  Read the article

• Outlook 2007 panes keep moving when changing resolution

  - by SilverbackNet

  This problem is really bugging one of our users ever since he got a larger monitor. Now that the monitor has a different resolution than his laptop, every time he unplugs it to go home, the three Outlook panes get all jumbled up. The navigation is huge, the list is shoved over, and the reading pane is almost smushed out of existence, the the opposite when he comes back in and the reading pane fills the screen. He's sick of adjusting it every day. He always runs it maximized, for maximum reading area. Keeping the application within a 1024x768 window wouldn't really be an option for him. Is there any way built into Outlook to automatically adjust pane sizes when the resolution changes? If not, is there a third-party app that can help, or a way to script the changes into the registry somehow? (I can do running the script whenever the screen state changes.) If this is fixed in 2010 I might be able to convince the other admin that this is a good enough reason to allow it (which will require a new beta version of our archiving software).

  Read the article

• How to make Firefox file associations consistent with Ubuntu file associations?

  - by wbharding

  This seems to be a pretty commonly Google question, but one for which there are no answers. http://www.linuxquestions.org/questions/linux-software-2/firefox-download-mime-types-378902 http://www.birkit.com/content/kubuntu-linux/internet/firefox/fix-file-associations-in-firefox.html Being three links amongst the many. The gist of what I want to accomplish is to have Firefox understand the file associations I download without me having to manually map all of them myself. Gnome knows the file extensions, so I would have expected that Firefox could just use the already-known file mappings there to open the right stuff (as I presume Chrome does). But it doesn't. At least not for me, using Firefox 4, and not by default. When I click on a downloaded file right now, Firefox always has to ask me what application should be used to open the file. A handful of Google results tell me that I can reassociate my file extensions by deleting ~/.mozilla/firefox/[profile name]/mimeTypes.rdf, but while deleting that file does in fact result in a new mimeTypes file being generated, the new mimeTypes is just as barren as the old one had been. Based on the amount of unanswered Qs on the Googlesphere, I know this is a very common problem for Ubuntu users, but it seems to be one for which nobody has chimed in with a good solution. Maybe Superuser can finally be the panacea for us all?

  Read the article

• Problem with setting up RAID 5 on FreeNAS

  - by Benjy23

  I've been running FreeNAS for a while now. Hardware is 1.8 GHz Celeron, RAM 1 GB. SATA card is Via - I am not sure about the model. It's 2 ports and I have 6 x 1.5 TB hard drives. All ran OK while running on 1.5 TB, no RAID. I'm now trying to create a RAID 5 with my 6 hard drives. Software RAID. Is it normal for it to take roughly up to 2 weeks just to build the RAID? Sorry, I'm very new to implementing RAID and googling doesn't tell much other than it takes a long time. Also the RAID building process seems to fail many times. Going to degraded. I suspect it's because 4 of my hard drives are connected to my motherboard and the other 2 are connected to my SATA card. What's your take? I'm considering 2 options now. Either get a 8 port SATA card and attach all the hard drives to it. Or get a RAID controller 8 portcard which is probably going to be more pricey. Also how do you access hardware RAID through FreeNAS? I like how FreeNAS emails you should your harddrive fails. Can this be done as well with hardware RAID?

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• Recommended drive encryption solution

  - by Chris Driver

  Hello, I will soon be purchasing a number of laptops running Windows 7 for our mobile staff. Due to the nature of our business I will need drive encryption. Windows BitLocker seems the obvious choice, but it looks like I need to purchase either Windows 7 Enterprise or Ultimate editions to get it. Can anyone offer suggestions on the best course of action: a) Use BitLocker, bite the bullet and pay to upgrade to Enterprise/Ultimate b) Pay for another 3rd party drive encryption product that is cheaper (suggestions appreciated) c) Use a free drive encryption product such as TrueCrypt Ideally I am also interested in 'real world' experience from people who are using drive encryption software and any pitfalls to look out for. Many thanks in advance... UPDATE Decided to go with TrueCrypt for the following reasons: a) The product has a good track record b) I am not managing a large quantity of laptops so integration with Active Directory, Management consoles etc is not a huge benefit c) Although eks did make a good point about Evil Maid (EM) attacks, our data is not that desirable to consider it a major factor d) The cost (free) is a big plus but not the primary motivator The next problem I face is imaging (Acronis/Ghost/..) encrypted drives will not work unless I perform sector-by-sector imaging. That means an 80Gb encrypted partition creates an 80Gb image file :(

  Read the article

• De-duplicating backup tool on a block basis? [closed]

  - by SST

  I am looking for an (ideally free as in speech or beer) backup tool for Unix-like OS which can store deduplicated backups, i.e. only nonredundant content takes up additional space. I already looked at dirvish (my first candidate) and rsnapshot which use hardlinks to achieve deduplication on a per-file level. However, as I want to back up large files (Thunderbird mailboxes 3GB, VMware images 10GB), such file are stored again entirely even if just a few bytes change. Then there are rsync-based tools like rdiff-backup which only store deltas and a current mirror. However, as the deltas are generated against each previous mirror, it is difficult to fine-tune the retention granularity (only keep one backup after a week, etc.) because the deltas would have to be re-evaluated. Another approach is to partition content into blocks and store each block only if it is not stored yet, otherwise just linking it to the first occurrence. The only tool I know of that does this by now is obnam (http://liw.fi/obnam), and it even supports zlib-compression and gpg-encryption -- nice! But it is very slow, AFAICT. Does any one know any other, solid backup software which supports deduplication on a sub-file level, ideally with at least some management options (show/select/delete generations...)?

  Read the article

• What format should I convert my iTunes Videos to?

  - by Aequitarum Custos

  Recently got Daniusoft Media Converter, and was about to strip the DRM off my iTunes library, then I found I had a huge decision to make. Converting my music seems obvious, to MP3, however the video formats, I'm at a loss on. It has "optimized" formats for all types of video players such as iPhone, Zune, Droid (which I own), and just a huge list! I bought several seasons of House and a few movies, though I don't know which format would be optimal to not lose quality. While I love my Droid, I have no intention on watching full episodes or movies on it, and I have a feeling that would reduce quality. One of the options sections is HD Video, and it has HD MPEG-4 Video (*.mp4). That one seems like it would be the best format to convert to without losing quality, but again, I'm unsure. Has anyone used this software, or have general expertise in video formats to give a recommendation on what file format I should convert my videos to? Format requirements: No loss in quality Portability would be ideal (as in, will play on my Windows and potentially MAC, and streamable to a bigscreen).

  Read the article

• Every month, scheduled task fails and password must be reset - why?

  - by Ducain

  [NOTE: I posted this originally at StackOverflow but it got no traction there - reposting here.] We have a bit of software installed at a few client locations that runs (via Windows task scheduler) a few times each day. In ONLY ONE of the client locations, we have a unique problem: each month, the task will stop working, after running every day for weeks. Twice now it's failed on the 2nd of the month. When I walk the client through troubleshooting it, we've found that it can't start - access denied. To fix it, we simply re-enter the same exact password, and then off it goes happy as a clam. I've never heard of this issue, and their IT people say they don't have anything running once a month that might cause that. I'm at a complete loss here. Any ideas as to why this might be happening? Further details: Windows XP pro machine. Task is being fired with credentials from a local admin account. Computer is always on, and connected to the net.

  Read the article

• What hardware would I need (approx) to run ESXi server?

  - by mr.b

  Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

  Read the article

• Whats the best cloud backup solution for a small scale server environment?

  - by nbv4

  I have a server that runs a postgres database that contains about 200MB of data. Currently I have a cron job setup on my home computer which: ssh's into my server runs a remote script which makes a backup of the database scp's that dump over to my local hard drive for storage. Each dump is 20MiB. does this every six hours (one months of backups is roughly 2GiB) The problem with this setup is that if my local machine goes down for whatever reason, no backups will be made. Also, I can't have the cron run from the server, because I can't have it scp'd to my local machine from my server (firewalls and all that crap). My local machine is running Ubuntu 10.04, and my server is Ubuntu 9.10 server edition. I looked into Ubuntu One, but currently it's gui-only. I also looked into dropbox, but it's a pain in the ass to get setup in linux without gui support. Amazon S3 looks good but it's not free (yet dirt cheap). Is there any other alternative that I should look into? I'd prefer something where I can just have my script dump the database into a directory, and have the backup service 'watch' that folder and sync accordingly. I can maybe also have my local machine sync to the cloud backup so I have even more redundancy, plus easy access to my backups for use in testing. Edit: My server is a VPS, so what solution I end up using has to be 100% software based.

  Read the article

• Help with routing table

  - by user68752

  I have tried to find the answer to my question but not really found a clean and easy solution. I have a box (Ubuntu headless 10.04.1 server, with one Ethernet port) on LAN behind a router (running m0n0wall), that I have successfully installed a PPTP device (ppp0) on, this is working flawlessly (following this link) The thing is I want this box to route all it's internet traffic through the VPN tunnel (ppp0 device) but also being able to access the local LAN on 192.168.1.* subnet. I've succeeded a bit with this, but my problem right now is that I have port forwards (e.g. SSH) done in the m0n0wall pointing to this specific box which forces me to do "add routes" to all boxes that want to access this machine through this specific port. For instance a machine with ip xyz.xyz.xyz.xyz needs to have a static route setup in the routing table on the box to be able to access the box. This is the result of route -n xxx.xxx.137.2 192.168.1.1 255.255.255.255 UGH 0 0 0 eth0 xxx.xxx.137.2 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 yyy.yyy.0.0 192.168.1.1 255.255.0.0 UG 0 0 0 eth0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 Where xxx is the IPs provided from VPN server. yyy.yyy.0.0 is a net that i want to have access to the box, without this I can't access the box from outside the LAN (via port-forwards done in router software, m0n0wall) is there away round this ugly solution?

  Read the article

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• Cloning a failing disk (Win 7)

  - by daveh551

  I have a Windows 7 machine with several partitions on a 1.5T drive. Windows has been complaining about disk errors and imminent failure, so I have purchased a new 2TB drive. The failing disk has not completely failed, and, in fact, I was able to boot Windows from it (after a couple tries) and examine the SMART logs - the only RED item was 1 sector being reallocated. But when I try to Clone it to the new Drive using Acronis True Image Home (2010), True Image can see the drive, the partitions, and the contents, but when it goes to actually do the clone, it says "Failed to move. Make sure the destination disk is not smaller than the source disk, and that there are not errors on the disk" (or something like that). What are some other options for simply cloning the failing drive. I'd like to clone the entire disk, but am willing to do it partition by partition if necessary. Was this a known failing of the 2010 edition of ATI, or is it really something hosed in my system. Would upgrading to the 2012 edition be likely to work any better? (I'd download the trial and try it out, but if I remember right, the cloning operation is disabled in the trial version), and I don't have enough free disk space to make an entire image.) What are some other cloning software packages if ATI won't work? Note that I'm only looking to clone the disk, not make an image as a back up - I use Ghost for that, and can fall back to that if I have to. It looks to me like CloneZilla would do the job. Any recommendations? Thanks, and if this duplicates other questions, I apologize.

  Read the article

• Copying files to my laptop makes them locked

  - by John

  When I save files from e.g. remote desktop or from an email (outlook) attachments, or from skype even to my local machine they show a locked Icon on the file. Then e.g. SQL Server doesn't let me restore backups as it says the operating system doesn't have access to the file. I've had success fixing this by setting the ownership of the parent folder to my user and then let it apply to sub folders. Also sometimes I need to click - Proerties - Security - Advanced - Change Permmissions, then check "change child permissions..." and apply on the parent dir. I'm using Windows 7 64 bit Proffessional, on HP Probook 4530, and I have a administrator user. This is a real pain to do everytime. I suspect it might be because of HP software that came with the laptop, I think there is drive encryption as part of the protect tools. Although I'm hoping there's something in windows i can set to change the behaviour to not lock these files.

  Read the article

• Migrating ODBC information through a batch file

  - by DeskSide

  I am a desktop support technician currently working on a large scale migration project across multiple sites. I am looking at a way to transfer ODBC entries from Windows XP to Windows 7. If anyone knows of a program or anything prebuilt that already does this, please redirect me. I've already looked but haven't found anything, so I'm trying to build my own. I know enough basic programming to read the work of others and monkey around with something that already exists, but not much else. I have come across a custom batch file written at one site that (among other things) exports ODBC information from the old computer and stores it on a server (labelled as y: through net use at the beginning of the file), then later transfers it from the server to a new computer. The pre-existing code is for Windows XP to XP migrations. Here are the pertinate bits of code: echo Exporting ODBC Information start /wait regedit.exe /e "y:\%username%\odbc.reg" HKEY_LOCAL_MACHINE\SOFTWARE\ODBC\ODBC.INI (and later on) echo Importing ODBC start /wait regedit /s "y:\%username%\odbc.reg" We are now migrating from Windows XP to 7, and this part of the batch file still seems to work for this particular site, where Oracle 8i and 10g are used. I'm looking to use my cut down version of this code at multiple sites, and I'm wondering if the same lines of code will still work for anything other than Oracle. Also, my research on this issue has shown that there are different locations in 64 bit operating systems for 32/64 bit entries, and I'm wondering what effect that would have on the code. Could I copy the same data to both parts of the registry, in hopes of catching everything? Any assistance would be appreciated. Thank you for your time.

  Read the article

• Windows 7 x64 support for Intel GMA 3650 (or GMA 3600)

  - by Loom

  I recently purchased an Intel D2700 MUD motherboard and I cannot find drivers for the Win7 x64 integrated graphics (Intel GMA 3650 aka PowerVR sgs545). The accompanying CD contains Win7 x32 version only. When I run it I got an error: This computer does not meet the minimum requirements for installing the software. I tried to use online utility Intel Driver Update Utility Graphics. I used Chrome, Firefox, Internet Explorer without success. First, UAC prompt appear, and then endlessly spinning progress-bar with text "Analyzing computer...". The text in UAC prompt is: Program file name: System Requirements Lab Verified publisher: Husdawg, LLC I downloaded this utility (intel_srldetect_4.5.5.0) and started it from my hard disk. I got an error: A network error occured while attempting to read from the file: C:\Users\Loom\Downloads\SystemRequirementsLab_intel_4.5.5.0.msi Standard VGA driver works for this video card but without hardware acceleration: Hardware acceleration is either disabled or not supported by your video card driver, which could slow game performance. Make sure you have the latest video card driver installed and that hardware acceleration is turned on. Where I can get appropriate driver?

  Read the article

• Periodic internet connection drops

  - by user9647

  My setup is a dsl modem, and a dlink di 524M router. I'm also using a Witopia VPN which runs through OpenVPN. I've been having trouble with the internet connection dropping very frequently. It comes back shortly, without even a router/modem/computer restart. This happens as frequently as every ten minutes. Occasionally (not often) it will last as long as an hour or two without dropping. When it drops, I can get it back almost immediately by clicking Reconnect in the OpenVPN GUI and letting that do it's thing. It's worth noting that I'm in China. Calling support is a bit difficult because of that. Also I don't really understand all of the router's software, although I've got it generally figured out. I've tried a bunch of stuff, attempts to diagnose and/or fix the problem. No success with any of the following: I've power cycled both the modem and the router. I've tried an ethernet connection to the router. I've connected without the VPN. I've disabled IEEE authentication on all connections. I've checked for viruses. I've tried lifting it off the ground so as to prevent overheating.

  Read the article

• RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

  - by Ed

  I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

  Read the article

• Modifying value of "Rating" column within Explorer for arbitrary file types

  - by Fake Name

  Basically, I have a large body of assorted media (text, images, flash files, archives, folders, etc...) and I'm attempting to organize it. Windows Explorer has a rating column, but there seems to be no way to modify the rating of the files short of opening them in their type-specific software (e.g. Media player, or Photo viewer). However, this does not work when the file is of an unsupported type (.rar, .swf ...), or a directory. I'd be more than willing to consider a file-manager replacement (I've alreadly looked at quite a few, Directory Opus, Total Commander, etc...), or even a solution that stores the rating metadata in a hidden file in each folder, or a separate database. The one real critical requirement is the ability to sort by rating, and being filetype-agnostic. Basically, is there any way to categorize a large collection of assorted files by rating that will work with any file type, including directories? - Ideally, there would be an easy way to add arbitrary columns to windows explorer, and edit them directly. However, there seems to be no way to do this. The rating column is the next best thing.

  Read the article

• Windows 7 automatically logs out when logging in

  - by Luke

  A Windows 7 HP x64 computer is set to automatically log in (no password), but once it starts logging in, it starts to load the desktop after the welcome screen, but before icons or background images are loaded, it goes to the Welcome screen saying 'Logging Off'. I can log in with Safe Mode, and I ran a couple different virus scans, with no detections. I also tried checking the userinit.exe file in System32 (as suggested by MANY users for Windows XP), but it's the same version as a working system. I also checked the registry under HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon for the SHELL and UserInit values, but they look normal. I tried to disable all startup items (through MSCONFIG) to select Diagnostic boot, but then I get a blue screen about the video driver not loading. Any other ideas? EDIT I created a new user, and it could log in no problems. I am thinking it's the NTUSER.DAT file. I just renamed it to NTUSER.DAT.old, then tried logging in as the problem user. I could log in, but as a TEMP profile. His profile folder is now C:\Users\TEMP, and his old folder is still accessible but in the wrong location. EDIT 2 I can't seem to turn off the TEMP profile, so I'm open to other suggestions. Copying the folders (i.e. Documents, Music, etc) does not work, as it creates an additional TEMP.000 then TEMP.001 folder each time the user logs in.

  Read the article

• windows 7 clock jumps back about every hour + internet disconnects

  - by IlyaD

  I have the weirdest problem, for the last few days every hour or so (not exact) the clock jumps about back in jumps of 15 to 60 minutes and after some time the internet disconnects. i can reconnect the internet by unplugging and plugging back the network cable. This is the second time this problem happens to me, the first time was when I installed VirtualBox. whaen I removed it the problem was gone. This time I have no idea what triggered it, the only thing I installed about the time the problem started was iTunes update (10.5.1) I tried removing it but the problem remained. (also tried to remove other programs i installed day or 2 before and it also didn't help) also, this is not a VM and currently I don't have any VM software. any ideas..? UPDATE since the solution is in the comments i'll write it here - apparently the windows time service got broken, this is the fix: http://technet.microsoft.com/en-us/library/cc738995(WS.10).aspx (run "fix it" from IE browser only) UPDATE 2 The fix didn't work, about 2 hours passed and first the internet disconnected and then the clock jumped back... This probably means that the problem is not only in the clock

  Read the article

• Basic connectivity issues between Win 7 and XP mixed wired/wireless network.

  - by Pulse

  Setup: Windows 7 x64 Ultimate desktop hard wired to Asus WL500gp router (WL500gpv2-1.9.2.7-d-r1445 firmware) Several Bridged VirtualBox VM's running XP, 7, ubuntu server 10.04, Mint 9 and SuSE 11.2 Win XP Pro SP3 notebook with D-Link Airplus wireless network card. No firewall or other security software currently running on either platform (at least for the duration of the test) Situation: Router is acting DHCP server Clients are receiving correct addresses and additional parameters Internet connectivity is available from all clients Windows 7 sharing is set to Network type = work (not home group) NetBT is disabled on all clients using smb over TCP What I can do: I can ping the router and internet addresses from the wireless XP notebook I can ping the Win 7 desktop and any VM from the XP wireless notebook I can ping all devices from the router All VM's and 7 can ping each other and the router as well as Internet addresses What I can't do: I cannot ping the XP wireless notebook from either The Win 7 desktop or the VM's it alwats returns a destination host unreachable. Tracert resolves the name or the XP notebook but also returns a destination host unreachable. From the above it would seem that something is blocking connectivity in a single direction (from the Win 7 box to the Win XP notebook) only but the router can ping the XP notebook. Some fresh input would be most welcome, as this is beginning to drive me batty. Thanks

  Read the article

< Previous Page | 716 717 718 719 720 721 722 723 724 725 726 727  | Next Page >