Search Results

Search found 30894 results on 1236 pages for 'best practice'.

Page 723/1236 | < Previous Page | 719 720 721 722 723 724 725 726 727 728 729 730  | Next Page >

• Cisco SG200 vlan issue in ESXi VSA cluster

  - by George

  I have three Cisco SG200-26 switches, and I also have two ESXi hosts that I have connected like shown in the below "best practice" map by VMware: http://communities.vmware.com/servlet/JiveServlet/previewBody/17393-102-1-22458/VSA_networking_map.pdf Even though I created the VLANs in the SG200 and I set the two VLANs (508 and 608) as allowed for these untagged ports (where my ESX NIC's are connected), I can not ping from host 1 to host 2 when configuring the NIC's to use 608 VLAN. Am I missing something? my IP's are all in the 192.168. range, and the only reason I need the VLANs is to isolate the traffic of VSA back-end internally, only the two hosts will be using the VLANs. So I think I do not have to create virtual interfaces on my router since that's the case, is my understanding correct? Also sending my switch config screenshot below.. all 3 switches have the latest firmware (it seems these were originally linksys and got rebranded as cisco after the acquisition) http://img31.imageshack.us/img31/2503/switch.gif Any ideas what to change on the Cisco SG200 to make this work , would be appreciated! The second VLAN (608) only needs two IP's: 192.168.0.1 and 192.168.0.2 The first VLAN (508) will have about 15 IP's for ESXi Management and VSA cluster service, I could use either 192.168.1.xx or 10.0.1.xx The rest of my network (about 50 clients) is in 192.168.1.xx range VMware also states that the VLAN protocol on the physical switch must be 802.1Q, not ISL, anyone knows which of the two my SG200-26 uses? In addition to that, the only requirement from VSA is that my two hosts: -Are in the same subnet. -Have static IP addresses set. -Have the same Default Gateway configured. If I need inter-vlan routing for this, I suppose I have to create virtual interfaces on my sonicwall, and assign an IP for each VLAN, and then set routes between them? Thank you for your time!

  Read the article

• Gmail and Live are making all messages from my server as spam.

  - by Ryan Kearney

  I'm getting very weird results here. When my server sends an email to my @hotmail or @gmail account, it's marked as spam. When I send email through my server from Outlook to @hotmail, it doesn't get marked as spam, but it still gets marked as spam in gmail. They seem to get through fine on Yahoo though. My servers hostname A record points to an IP address whose PTR record points back to the same domain name. The TXT record has a SPF record in it to allow email to be sent from that servers IP. I moved from a VPS to a Dedicated server when this started to happen. From what I can see, the email headers are identical. Here's one of my email headers that gmail marks as spam. Some fields were repalced. MYGMAILACCOUNT is the email address of the account the email was addressed to. USER is the name of the account on the system it was sent from HOSTNAME is the servers FQDN IPADDR is the IP Address of the Hostname MYDOMAIN is my domain name Delivered-To: MYGMAILACCOUNT Received: by 10.220.77.82 with SMTP id f18cs263483vck; Sat, 27 Feb 2010 23:58:02 -0800 (PST) Received: by 10.150.16.4 with SMTP id 4mr3886702ybp.110.1267343881628; Sat, 27 Feb 2010 23:58:01 -0800 (PST) Return-Path: <USER@HOSTNAME> Received: from HOSTNAME (HOSTNAME [IPADDR]) by mx.google.com with ESMTP id 17si4604419yxe.134.2010.02.27.23.58.01; Sat, 27 Feb 2010 23:58:01 -0800 (PST) Received-SPF: pass (google.com: best guess record for domain of USER@HOSTNAME designates IPADDR as permitted sender) client-ip=IPADDR; Authentication-Results: mx.google.com; spf=pass (google.com: best guess record for domain of USER@HOSTNAME designates IPADDR as permitted sender) smtp.mail=USER@HOSTNAME Received: from USER by HOSTNAME with local (Exim 4.69) (envelope-from <USER@HOSTNAME>) id 1Nle2K-0000t8-Bd for MYGMAILACCOUNT; Sun, 28 Feb 2010 02:57:36 -0500 To: Ryan Kearney <MYGMAILACCOUNT> Subject: [Email Subject] MIME-Version: 1.0 Content-type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit From: webmaster@MYDOMAIN Message-Id: <E1Nle2K-0000t8-Bd@HOSTNAME> Sender: <USER@HOSTNAME> Date: Sun, 28 Feb 2010 02:57:36 -0500 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - HOSTNAME X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [503 500] / [47 12] X-AntiAbuse: Sender Address Domain - HOSTNAME Anyone have any ideas as to why all mail leaving my server gets marked as spam? EDIT: I already used http://www.mxtoolbox.com/SuperTool.aspx to check if my servers IP's are blacklisted and they are in fact not. That's what I thought at first, but it isn't the case. Update Mar 1, 2010 I received the following email from Microsoft Thank you for writing to Windows Live Hotmail Domain Support. My name is * and I will be assisting you today. We have identified that messages from your IP are being filtered based on the recommendations of the SmartScreen filter. This is the spam filtering technology developed and operated by Microsoft and is built around the technology of machine learning. It learns to recognize what is and isn't spam. In short, we filter incoming emails that look like spam. I am not able to go into any specific details about what these filters specifically entail, as this would render them useless. E-mails from IPs are filtered based upon a combination of IP reputation and the content of individual emails. The reputation of an IP is influenced by a number of factors. Among these factors, which you as a sender can control, are: The IP's Junk Mail Reporting complaint rate The frequency and volume in which email is sent The number of spam trap account hits The RCPT success rate So I'm guessing it has to do with the fact that I got an IP address with little or no history in sending email. I've confirmed that I'm not on any blacklists. I'm guessing it's one of those things that will work itself out in a month or so. I'll post when I hear more.

  Read the article

• To clone or to automate a system installation?

  - by Shtééf

  Let's say you're setting up a cluster of servers performing the same task. Or say you're just setting up a bunch of different servers, but you expect to use a base configuration on all of your servers. Would it be better practice to create a base image and clone it, or to automate the installation and configuration? I occasionally end up in this argument with my boss, in situations where we're time-pressed. When he sees me struggle with perfecting the automation, his suggestion is often to clone the entire disk to the other machines. But my instinct has always been to avoid cloning. This is mostly from an Ubuntu perspective, but the question is fairly general. My reasons for avoiding cloning are: On a typical install, even if it's fresh, there are already several unique identifiers installed: filesystem UUIDs, SSH host keys, among others. These would have to be regenerated. Network needs to be reconfigured for each clone. This would need to be done off-line, of course, or the settings will conflict with other machines on the network. On the other hand, some of the cloning advantages are quite clear as well: (Initially?) less effort required than automating configuration. Tools exist to quickly address (some) of the above disadvantages. (I can see right through my own bias there.)

  Read the article

• Changing subnet-mask of class-c network host to 255.255.0.0

  - by Prashant Mandhare

  We have a existing class-c network with IP address range 11.22.33.44/24 (just for example). My domain controller has been configured within this subnet. So all servers within this subnet have subnet mask configured to 255.255.255.0. Now we have got a new subnet with IP address 11.22.88.99/24 (note that only last 2 octets have changed). I want all new hosts in this new subnet to join my existing DC. For this we have configured firewall properly so allow this. (so there is no issue with firewall). But initially I was not able to join hosts in new subnet in existing domain. Later I doubted on subnet mask used in domain controller (255.255.255.0) and for testing purpose I changed it to 255.255.0.0, it worked like charm, i was able to join subnet-2 hosts in subnet-1 domain. Now i am wondering whether it will be good practice to change subnet mask of a class-c network to 255.255.0.0? Can any issues arise due to this? Experts please provide your opinion.

  Read the article

• Oracle performance problem

  - by jreid42

  We are using an Oracle 11G machine that is very powerful; has redundant storage etc. It's a beast from what I have been told. We just got this DB for a tool that when I first came on as a coop had like 20 people using, now its upwards of 150 people. I am the only one working on it :( We currently have a system in place that distributes PERL scripts across our entire data center essentially giving us a sort of "grid" computing power. The Perl scripts run a sort of simulation and report back the results to the database. They do selects / inserts. The load is not very high for each script but it could be happening across 20-50 systems at the same time. We then have multiple data centers and users all hitting the same database with this same approach. Our main problem with this is that our database is getting overloaded with connections and having to drop some. We sometimes have upwards of 500 connections. These are old perl scripts and they do not handle this well. Essentially they fail and the results are lost. I would rather avoid having to rewrite a lot of these as they are poorly written, and are a headache to even look at. The database itself is not overloaded, just the connection overhead is too high. We open a connection, make a quick query and then drop the connection. Very short connections but many of them. The database team has basically said we need to lower the number of connections or they are going to ignore us. Because this is distributed across our farm we cant implement persistent connections. I do this with our webserver; but its on a fixed system. The other ones are perl scripts that get opened and closed by the distribution tool and thus arent always running. What would be my best approach to resolving this issue? The scripts themselves can wait for a connection to be open. They do not need to act immediately. Some sort of queing system? I've been suggested to set up a few instances of a tool called "SQL Relay". Maybe one in each data center. How reliable is this tool? How good is this approach? Would it work for what we need? We could have one for each data center and relay requests through it to our main database, keeping a pipeline of open persistent connections? Does this make sense? Is there any other suggestions you can make? Any ideas? Any help would be greatly appreciated. Sadly I am just a coop student working for a very big company and somehow all of this has landed all on my shoulders (there is literally nobody to ask for help; its a hardware company, everybody is hardware engineers, and the database team is useless and in India) and I am quite lost as what the best approach would be? I am extremely overworked and this problem is interfering with on going progress and basically needs to be resolved as quickly as possible; preferably without rewriting the whole system, purchasing hardware (not gonna happen), or shooting myself in the foot. HELP LOL!

  Read the article

• Network authentication + roaming home directory - which technology should I look into using?

  - by Brian

  I'm looking into software which provides a user with a single identity across multiple computers. That is, a user should have the same permissions on each computer, and the user should have access to all of his or her files (roaming home directory) on each computer. There seem to be many solutions for this general idea, but I'm trying to determine the best one for me. Here are some details along with requirements: The network of machines are Amazon EC2 instances running Ubuntu. We access the machines with SSH. Some machines on this LAN may have different uses, but I am only discussing machines for a certain use (running a multi-tenancy platform). The system will not necessarily have a constant amount of machines. We may have to permanently or temporarily alter the amount of machines running. This is the the reason why I'm looking into centralized authentication/storage. The implementation of this effect should be a secure one. We're unsure if users will have direct shell access, but their software will potentially be running (under restricted Linux user names, of course) on our systems, which is as good as direct shell access. Let's assume that their software could potentially be malicious for the sake of security. I have heard of several technologies/combinations to achieve my goal, but I'm unsure of the ramifications of each. An older ServerFault post recommended NFS & NIS, though the combination has security problems according to this old article by Symantec. The article suggests moving to NIS+, but, as it is old, this Wikipedia article has cited statements suggesting a trending away from NIS+ by Sun. The recommended replacement is another thing I have heard of... LDAP. It looks like LDAP can be used to save user information in a centralized location on a network. NFS would still need to be used to cover the 'roaming home folder' requirement, but I see references of them being used together. Since the Symantec article pointed out security problems in both NIS and NFS, is there software to replace NFS, or should I heed that article's suggestions for locking it down? I'm tending toward LDAP because another fundamental piece of our architecture, RabbitMQ, has a authentication/authorization plugin for LDAP. RabbitMQ will be accessible in a restricted manner to users on the system, so I would like to tie the security systems together if possible. Kerberos is another secure authentication protocol that I have heard of. I learned a bit about it some years ago in a cryptography class but don't remember much about it. I have seen suggestions online that it can be combined with LDAP in several ways. Is this necessary? What are the security risks of LDAP without Kerberos? I also remember Kerberos being used in another piece of software developed by Carnegie Mellon University... Andrew File System, or AFS. OpenAFS is available for use, though its setup seems a bit complicated. At my university, AFS provides both requirements... I can log in to any machine, and my "AFS folder" is always available (at least when I acquire an AFS token). Along with suggestions for which path I should look into, does anybody have any guides which were particularly helpful? As the bold text pointed out, LDAP looks to be the best choice, but I'm particularly interested in the implementation details (Keberos? NFS?) with respect to security.

  Read the article

• Managing Many External Hosts Using EC2 and Route 53

  - by futureal

  Looking for a "best practice" answer to managing externally-addressable hosts using the combination of Amazon EC2 and Amazon Route 53, without using Elastic IPs for each host. In my scenario I will have 30+ hosts that need to be accessible from outside EC2, so directly using internal DNS will not work. In the past, I have addressed hosts by assigning an elastic IP to that host (let's say, 55.55.55.55) and then creating an associated A record. For example, let's say I want to create "ec2-corp01.mydomain.com" I might do: ec2-corp01.mydomain.com. A 55.55.55.55 300 Then on that EC2 instance, I would assign the Elastic IP of 55.55.55.55, and everything works fine. Of course, to make this work, I need to have one Elastic IP per instance, which is something I'd like to avoid if possible; I'd like the infrastructure to be more dynamic. So my thought is to try something like: Create a script that queries the internal EC2 tools to determine an instance's private hostname On instance boot, call that script to determine its hostname, and then using the command-line Route 53 interface to find and update that hostname to its current internal hostname Since the host will have a relatively low TTL (let's say 300 as above, or 5 minutes) it should take effect pretty quickly Is this a good idea? Is there a better or more widely accepted way to handle it? If it IS a good idea, what type of record should I be creating? A CNAME that points to the internal host, like ec2-55-55-55-55.compute-1.amazonaws.com? Is an A record better or worse? Thanks!

  Read the article

• Windows roaming profile when creating a new user profile

  - by molecule

  When a particular user is having a lot of problems with Windows XP e.g. applications crashing, unresponsive applications (which used to work), and as a general troubleshooting practice for a domain user, I normally rename that user's old profile and get him/her to logon to create a "fresh" profile (on the same PC). More often than not, this will solve the problem albeit some reconfiguration i.e. Outlook, Excel add-ins etc. As I took over the systems admin role from another administrator, I would like to know what is the easiest way to find out (either through a third party or some Windows administrative tool) what settings are carried over if the profile is a Roaming Profile. I tested creating a new user profile for one of my users and it seems basic Outlook settings such as the user's mailbox and PSTs are carried over automatically when I create a new user profile. I suspect this is done through a batch file loaded as part of the login script. However, my knowledge of scripting is limited and I don't want any corruptions to be carried over to the new profile. Can someone share their experiences on this? Thanks in advance.

  Read the article

• Why is my own e-mail address not listed in the To field?

  - by Sammy

  I have received a suspicious e-mail. I am not affiliated with the company mentioned in the e-mail body, or the signer. However, I have been using the app they mention in the e-mail. They are inviting me to a Beta test. But the e-mail is not by the original author of the app. But I'm thinking they might have hired an external company to do this version of the app. There is a link to a TestFlight page. So I'm not sure what to make of this. Now this is what mainly arose my attention. From: Anders Bergman <[email protected]> To: Bon Support Cc: Subject: Test av nya BBK för Android This is how it shows up in Outlook 2010. The "To" field is addressed to "Bon Support" and when I double-click on that I see [email protected]. I can assure you that none of these are my e-mail addresses. So where the heck is my own e-mail address? How could I have received this if it was addressed to someone else? If not spammers and skimmers and other criminals, who else is using this practice and why? And how can I tell now to what e-mail account I received this? I have more than one account set up in Outlook.

  Read the article

• If spaces in filenames are possible, why do some of us still avoid using them?

  - by Chris W. Rea

  Somebody I know expressed irritation today regarding those of us who tend not to use spaces in our filenames, e.g. NamingThingsLikeThis.txt -- despite most modern operating systems supporting spaces in filenames. Non-technical people must look at filenames created by geeks and wonder where we learned English. So, what are the reasons that spaces in filenames are avoided or discouraged? The most obvious reason I could think of, and why I typically avoid it, are the extra quotes required on the command line when dealing with such files. Are there any other significant reasons, other than the practice being a vestigial preference? UPDATE: Thanks for all your answers! I'm surprised how popular this was. So, here's a summary: Six Reasons Why Geeks Prefer Filenames Without Spaces In Them It's irritating to put quotes around them when referenced on the command line (or elsewhere.) Some older operating systems didn't used to support them and us old dogs are used to that. Some tools still don't support spaces in filenames at all or very well. (But they should.) It's irritating to escape spaces when used where spaces must be escaped, such as URLs. Certain unenlightened services (e.g. file hosting, webmail) remove or replace spaces anyway! Names without spaces can be shorter, which is sometimes desirable as paths are limited.

  Read the article

• AMD FX8350 CPU - CoolerMaster Silencio 650 Case - New Water Cooling System

  - by fat_mike

  Lately after a use of 6 months of my AMD FX8350 CPU I'm experiencing high temperatures and loud noise coming from the CPU fan(I set that in order to keep it cooler). I decided to replace the stock fan with a water cooling system in order to keep my CPU quite and cool and add one or two more case fans too. Here is my case's airflow diagram: http://www.coolermaster.com/microsite/silencio_650/Airflow.html My configuration now is: 2x120mm intake front(stock with case) 1x120mm exhaust rear(stock with case) 1 CPU stock I'm planning to buy Corsair Hydro Series H100i(www.corsair.com/en-us/hydro-series-h100i-extreme-performance-liquid-cpu-cooler) and place the radiator in the front of my case(intake) and add an 120mm bottom intake and/or an 140mm top exhaust fan. My CPU lies near the top of the MO. Is it a good practice to have a water-cooling system that takes air in? As you can see here the front of the case is made of aluminum. Can the fresh air go in? Does it even fit? If not, is it wiser to get Corsair Hydro Series H80i (www.corsair.com/en-us/hydro-series-h80i-high-performance-liquid-cpu-cooler) and place the radiator on top of my case(exhaust) and keep the front 2x120mm stock and add one more as intake on bottom. If you have any other idea let me know. Thank you. EDIT: The CPU fan running ~3000rpm and temp is around 40~43C on idle and save energy. When temp is going over 55C when running multiple programs and servers on localhost(tomcat, wamp) rpm is around 5500 and loud! I'm running Win8.1 CPU not overclocked PS: Due to my reputation i couldn't post the links that was necessary. I will edit ASAP.

  Read the article

• What can lead to a zone memory exhaustion and how Nginx reacts to it?

  - by Miles Hughes

  What is a possible scenario for exhausting the memory designated to a connection zone with limit_conn_zone directive and what are the implication in this case? Suppose I have this in my configuration: http { limit_conn_zone $binary_remote_addr zone=connzone:1m; ... server { limit_conn connzone 5; which, according to the documentation, allocates 16000 states for connzone on a 64-bit server. It also says that If the storage for a zone is exhausted, the server will return error 503 (Service Temporarily Unavailable) to all further requests. Well, Ok. But what does it mean on practice? When does this happen? Who receives those 503s? Does it mean that if the number of IPs somehow associated with connzone hits 16000 everyone gets a 503 and it's all over? How does Nginx decide? The documentation is weirdly vague on this. So, considering the example config, who would actually get a 503 and under which circumstances and how would things go from there? Same with request zones?

  Read the article

• RSA keys - virtual hosts

  - by Bosworth99

  Pardon my noobness, but I just got started with VPS (linux) hosting; setting up passwordless ssh for multiple users has proved to be kind of a pain. Currently I'm the single user of this ubuntu 10.04 LTS VPS (linode.com). I was able to establish a single rsa passkey under my home/user/.ssh/authorized_keys location. Fine. PuTTy works as expected, and Filezilla (sftp) links up as required. I've been working on a single site that this user owns, and thats not been a problem. Now, I want to set up some other sites, and I've chosen Webmin with the VirtualMin plugin to make this work. I made another user (or, rather, virtualmin did), but I've been unable to get FileZilla to link up to this new user. Could anyone with experience here explain what the setup is supposed to look like? IE - can I use a single rsa key pair for all accounts (if, for example, I give ownership of files to the original user?). Or is it standard practice to create a separate key pair for each user, and establish a separate putty/filezilla login for each? I've spent enough time dinking around with this to be frustrated. "Sever rejected the provided key" error sucks after the fifth hour. I'm about to set up an ftp server and call it a day. Any thoughts would be most welcome -

  Read the article

• Network Management Cable Labeling Techniques and their alternatives [closed]

  - by Alex

  Possible Duplicate: What is the most effective solution you used to label cables? Yes i know there are a lot of howtos and already answered questions about this topic, like this one: How do you organise the cables in your racks? Currently i am searching the web for different techniques (alternatives) for labeling the cables at the server racks and/or data centers. Unfortunately i do not have any experience with labeling/documentation of network cables in a large scale. As far as I could lookup by now the current labeling techniques are coloring and a self defined print-labeling technique (numbering, text) maybe also according to a standard which are usually used. I want to know if QR, RFID (ok RFID in a data center would be stupid due to the radio frequency wouldn't it be?), Barcodes or similar (??) have already been used by some administrators or why they did not consider such techniques at all? Too complicated (with QR scanner etc..) if you are in front of the cables and want to get quick feedback for what the cable is? What alternatives are out there? Advantages/Disadvantages? Best-Practice? I would appreciate any help on this topic, thank you! Regards, Alex

  Read the article

• Is there a fix to display 0 when arithmetic underflow occurs on the Windows 7 calculator?

  - by Pascal Qyy

  I have a problem that exasperates me: When I take the Windows 7 calculator in standard mode, if I do 4, then v (square root), the result is 2 Fine. But, at this point, if I do - (minus), then 2, the result is -1,068281969439142e-19 instead of 0! OK, I know about ? (machine epsilon), and yes, -1,068281969439142e-19 is less than the 64 bits ? (1.11e-16), so, we have an arithmetic underflow, in other words in this case: 0. Great, my computer is able to represent subnormal numbers instead of just flush to zero when this happens, and it seems that it is an improvement! Subnormal values fill the underflow gap with values where the absolute distance between them are the same as for adjacent values just outside of the underflow gap. This is an improvement over the older practice to just have zero in the underflow gap, and where underflowing results were replaced by zero (flush to zero). BUT: this result is false! when you try to explain the concept of the square root to a child and you end up with this kind of result, it only complicates your task... what is the point to represent subnormal numbers in a standard, non scientific calculator? So, is there a way to fix this?

  Read the article

• Windows roaming profile when creating a new Windows profile

  - by molecule

  Hi all, When a particular user is having a lot of problems with Windows XP e.g. applications crashing, unresponsive applications (which used to work), and as a general troubleshooting practice for a domain user, I normally rename that user's old profile and get him/her to logon to create a "fresh" profile (on the same PC). More often than not, this will solve the problem albeit some reconfiguration i.e. Outlook, Excel add-ins etc. As I took over the systems admin role from another administrator, I would like to know what is the easiest way to find out (either through a third party or some Windows administrative tool) what settings are carried over if the profile is a Roaming Profile. I tested creating a new user profile for one of my users and it seems basic Outlook settings such as the user's mailbox and PSTs are carried over automatically when I create a new user profile. I suspect this is done through a batch file loaded as part of the login script. However, my knowledge of scripting is limited and I don't want any corruptions to be carried over to the new profile. Can someone share their experiences on this? Thanks in advance.

  Read the article

• Windows roaming profile when creating a new user profile

  - by molecule

  Hi all, When a particular user is having a lot of problems with Windows XP e.g. applications crashing, unresponsive applications (which used to work), and as a general troubleshooting practice for a domain user, I normally rename that user's old profile and get him/her to logon to create a "fresh" profile (on the same PC). More often than not, this will solve the problem albeit some reconfiguration i.e. Outlook, Excel add-ins etc. As I took over the systems admin role from another administrator, I would like to know what is the easiest way to find out (either through a third party or some Windows administrative tool) what settings are carried over if the profile is a Roaming Profile. I tested creating a new user profile for one of my users and it seems basic Outlook settings such as the user's mailbox and PSTs are carried over automatically when I create a new user profile. I suspect this is done through a batch file loaded as part of the login script. However, my knowledge of scripting is limited and I don't want any corruptions to be carried over to the new profile. Can someone share their experiences on this? Thanks in advance.

  Read the article

• how does svn work with apache?

  - by ajsie

  i've got ubuntu installed with lamp. im using webdav to upload/download files to/from the ubuntu web server, after i have edited the php source files in netbeans. however, i wonder what is best practice for editing source files and committing these changes to the new website. cause if we are 2-3 developers, i guess we have to use svn. but i have never used it before so i wonder how it works. should i install it and then select the /var/www (apaches webroot) as the repository folder? then when i check in, all the changes will apply immediately? could someone please explain following steps: how to download, edit the source files, upload the files and see the new changes in the website. cause i have only worked with a local apache before, and it was only me. now there will be some more programmers so i have to set up a decent, central environment for this, and have to know how netbeans, svn, webdav and apache works all together. thanks!

  Read the article

• What would keep a Microsoft Word AutoNew() macro from running?

  - by Chris Nelson

  I'm using Microsoft Office 2003 and creating a bunch of template documents to standardize some tasks. I know it's standard practice to put the templates in an certain place Office expects to find them but that won't work for me. What I want is to have "My Template Foo.dot" and "My Template Bar.dot", etc. in the "My Foo Bar Stuff" on a shared drive and users will double click on the template to create a new Foo or Bar. What's I'd really like is for the user to double click on the Foo template and be prompted for a couple of items related to their task (e.g., a project number) and have a script in the template change the name that Save will default to something like "Foo for Project 1234.doc". I asked on Google Groups and got an answer that worked....for a while. Then my AutoNew macro stopped kicking in when I created a new document by double clicking on the template. I have no idea why or how to debug it. I'm a software engineering with 25+ years of experience but a complete Office automation noob. Specific solutions and pointers to "this is how to automate Word" FAQs are welcome. Thanks.

  Read the article

• javax.naming.InvalidNameException using Oracle BPM and weblogic when accessing directory

  - by alfredozn

  We are getting this exception when we start our cluster (2 managed servers, 1 admin), we have deployed only the ears corresponding to the OBPM 10.3.1 SP1 in a weblogic 10.3. When the server cluster starts, one of the managed servers (the first to start) get overloaded and ran out of connections to the directory DB because of this repeatedly error. It looks like the engine is trying to get the info from the LDAP server but I don't know why it is building a wrong query. fuego.directory.DirectoryRuntimeException: Exception [javax.naming.InvalidNameException: CN=Alvarez Guerrero Bernardo DEL:ca9ef28d-3b94-4e8f-a6bd-8c880bb3791b,CN=Deleted Objects,DC=corp: [LDAP: error code 34 - 0000208F: NameErr: DSID-031001BA, problem 2006 (BAD_NAME), data 8349, best match of: 'CN=Alvarez Guerrero Bernardo DEL:ca9ef28d-3b94-4e8f-a6bd-8c880bb3791b,CN=Deleted Objects,DC=corp,dc=televisa,dc=com,dc=mx' ^@]; remaining name 'CN=Alvarez Guerrero Bernardo DEL:ca9ef28d-3b94-4e8f-a6bd-8c880bb3791b,CN=Deleted Objects,DC=corp']. at fuego.directory.DirectoryRuntimeException.wrapException(DirectoryRuntimeException.java:85) at fuego.directory.hybrid.ldap.JNDIQueryExecutor.selectById(JNDIQueryExecutor.java:163) at fuego.directory.hybrid.ldap.JNDIQueryExecutor.selectById(JNDIQueryExecutor.java:110) at fuego.directory.hybrid.ldap.Repository.selectById(Repository.java:38) at fuego.directory.hybrid.msad.MSADGroupValueProvider.getAssignedParticipantsInternal(MSADGroupValueProvider.java:124) at fuego.directory.hybrid.msad.MSADGroupValueProvider.getAssignedParticipants(MSADGroupValueProvider.java:70) at fuego.directory.hybrid.ldap.Group$7.getValue(Group.java:149) at fuego.directory.hybrid.ldap.Group$7.getValue(Group.java:152) at fuego.directory.hybrid.ldap.LDAPResult.getValue(LDAPResult.java:76) at fuego.directory.hybrid.ldap.LDAPOrganizationGroupAccessor.setInfo(LDAPOrganizationGroupAccessor.java:352) at fuego.directory.hybrid.ldap.LDAPOrganizationGroupAccessor.build(LDAPOrganizationGroupAccessor.java:121) at fuego.directory.hybrid.ldap.LDAPOrganizationGroupAccessor.build(LDAPOrganizationGroupAccessor.java:114) at fuego.directory.hybrid.ldap.LDAPOrganizationGroupAccessor.fetchGroup(LDAPOrganizationGroupAccessor.java:94) at fuego.directory.hybrid.HybridGroupAccessor.fetchGroup(HybridGroupAccessor.java:146) at sun.reflect.GeneratedMethodAccessor66.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at fuego.directory.provider.DirectorySessionImpl$AccessorProxy.invoke(DirectorySessionImpl.java:756) at $Proxy66.fetchGroup(Unknown Source) at fuego.directory.DirOrganizationalGroup.fetch(DirOrganizationalGroup.java:275) at fuego.metadata.GroupManager.loadGroup(GroupManager.java:225) at fuego.metadata.GroupManager.find(GroupManager.java:57) at fuego.metadata.ParticipantManager.addNestedGroups(ParticipantManager.java:621) at fuego.metadata.ParticipantManager.buildCompleteRoleAssignments(ParticipantManager.java:527) at fuego.metadata.Participant$RoleTransitiveClousure.build(Participant.java:760) at fuego.metadata.Participant$RoleTransitiveClousure.access$100(Participant.java:692) at fuego.metadata.Participant.buildRoles(Participant.java:401) at fuego.metadata.Participant.updateMembers(Participant.java:372) at fuego.metadata.Participant.<init>(Participant.java:64) at fuego.metadata.Participant.createUncacheParticipant(Participant.java:84) at fuego.server.persistence.jdbc.JdbcProcessInstancePersMgr.loadItems(JdbcProcessInstancePersMgr.java:1706) at fuego.server.persistence.Persistence.loadInstanceItems(Persistence.java:838) at fuego.server.AbstractInstanceService.readInstance(AbstractInstanceService.java:791) at fuego.ejbengine.EJBInstanceService.getLockedROImpl(EJBInstanceService.java:218) at fuego.server.AbstractInstanceService.getLockedROImpl(AbstractInstanceService.java:892) at fuego.server.AbstractInstanceService.getLockedImpl(AbstractInstanceService.java:743) at fuego.server.AbstractInstanceService.getLockedImpl(AbstractInstanceService.java:730) at fuego.server.AbstractInstanceService.getLocked(AbstractInstanceService.java:144) at fuego.server.AbstractInstanceService.getLocked(AbstractInstanceService.java:162) at fuego.server.AbstractInstanceService.unselectAllItems(AbstractInstanceService.java:454) at fuego.server.execution.ToDoItemUnselect.execute(ToDoItemUnselect.java:105) at fuego.server.execution.DefaultEngineExecution$AtomicExecutionTA.runTransaction(DefaultEngineExecution.java:304) at fuego.transaction.TransactionAction.startNestedTransaction(TransactionAction.java:527) at fuego.transaction.TransactionAction.startTransaction(TransactionAction.java:548) at fuego.transaction.TransactionAction.start(TransactionAction.java:212) at fuego.server.execution.DefaultEngineExecution.executeImmediate(DefaultEngineExecution.java:123) at fuego.server.execution.DefaultEngineExecution.executeAutomaticWork(DefaultEngineExecution.java:62) at fuego.server.execution.EngineExecution.executeAutomaticWork(EngineExecution.java:42) at fuego.server.execution.ToDoItem.executeAutomaticWork(ToDoItem.java:261) at fuego.ejbengine.ItemExecutionBean$1.execute(ItemExecutionBean.java:223) at fuego.server.execution.DefaultEngineExecution$AtomicExecutionTA.runTransaction(DefaultEngineExecution.java:304) at fuego.transaction.TransactionAction.startBaseTransaction(TransactionAction.java:470) at fuego.transaction.TransactionAction.startTransaction(TransactionAction.java:551) at fuego.transaction.TransactionAction.start(TransactionAction.java:212) at fuego.server.execution.DefaultEngineExecution.executeImmediate(DefaultEngineExecution.java:123) at fuego.server.execution.EngineExecution.executeImmediate(EngineExecution.java:66) at fuego.ejbengine.ItemExecutionBean.processMessage(ItemExecutionBean.java:209) at fuego.ejbengine.ItemExecutionBean.onMessage(ItemExecutionBean.java:120) at weblogic.ejb.container.internal.MDListener.execute(MDListener.java:466) at weblogic.ejb.container.internal.MDListener.transactionalOnMessage(MDListener.java:371) at weblogic.ejb.container.internal.MDListener.onMessage(MDListener.java:327) at weblogic.jms.client.JMSSession.onMessage(JMSSession.java:4547) at weblogic.jms.client.JMSSession.execute(JMSSession.java:4233) at weblogic.jms.client.JMSSession.executeMessage(JMSSession.java:3709) at weblogic.jms.client.JMSSession.access$000(JMSSession.java:114) at weblogic.jms.client.JMSSession$UseForRunnable.run(JMSSession.java:5058) at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTuningWorkManagerImpl.java:516) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201) at weblogic.work.ExecuteThread.run(ExecuteThread.java:173) Caused by: javax.naming.InvalidNameException: CN=Alvarez Guerrero Bernardo DEL:ca9ef28d-3b94-4e8f-a6bd-8c880bb3791b,CN=Deleted Objects,DC=corp: [LDAP: error code 34 - 0000208F: NameErr: DSID-031001BA, problem 2006 (BAD_NAME), data 8349, best match of: 'CN=Alvarez Guerrero Bernardo DEL:ca9ef28d-3b94-4e8f-a6bd-8c880bb3791b,CN=Deleted Objects,DC=corp,dc=televisa,dc=com,dc=mx' ^@]; remaining name 'CN=Alvarez Guerrero Bernardo DEL:ca9ef28d-3b94-4e8f-a6bd-8c880bb3791b,CN=Deleted Objects,DC=corp' at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2979) at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2794) at com.sun.jndi.ldap.LdapCtx.searchAux(LdapCtx.java:1826) at com.sun.jndi.ldap.LdapCtx.c_search(LdapCtx.java:1749) at com.sun.jndi.toolkit.ctx.ComponentDirContext.p_search(ComponentDirContext.java:368) at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.search(PartialCompositeDirContext.java:338) at com.sun.jndi.toolkit.ctx.PartialCompositeDirContext.search(PartialCompositeDirContext.java:321) at javax.naming.directory.InitialDirContext.search(InitialDirContext.java:248) at fuego.jndi.FaultTolerantLdapContext.search(FaultTolerantLdapContext.java:612) at fuego.directory.hybrid.ldap.JNDIQueryExecutor.selectById(JNDIQueryExecutor.java:136) ... 67 more

  Read the article

• Xen guests accessing LUNs

  - by mechcow

  We are using RHEL5.3 with a Clarion SAN attached by FC. Our situation is that we have a number of LUNs presented to Hosts and we want to dynamically present the LUNs to Xen Guests. We are not sure on what the best practice approach is to set this up. The Xen guests will form a cluster together and need the LUNs only for data partitions, i.e. when they are actively running services. So one approach would be to always present all disks to all Xen guests, and then rely up on the cluster software, and mount itself, to not mount the disk twice in two locations. This sounds kinda risky and also is not very secure (one cracked guest can see/destroy all the data). Another approach would be to dynamically add and remove the disks from the Xen guests at the dom0 level (using xm block-attach). This could work but sounds slightly complicated, I'm wondering whether Red Hat Cluster Suite supports this in some way or whether there are scripts to do this. Yet another approach would be to have the LUNs endpointed at the Xen guests themselves - I'm not sure whether this is technically possible since the multipathing has to be done at the Host level.

  Read the article

• script calling script as other user

  - by viktor tron

  Using CentOs, I want to run a script as user 'training' as a system service. I use daemontools to monitor the process, which needs a launcher script that is run as root: : #!/bin/bash exec >> /var/log/training_service.log 2>&1 setuidgid training training_command This last line is not good enough since for training_command, we need environment for training user to be set. : su - training -c 'training_command' gives 'standard in must be tty' as su making sure tty is present to potentially accept password. I know I could make this disappear by modifying /etc/sudoers a la Bash & 'su' script giving an error "standard in must be a tty" but i am reluctant and unsure of consequences. : runuser - training -c 'training_command' gives runuser: cannot set groups: Connection refused. I found no sense or resolution to this message. I am stuck. Is this something so hard to achieve? I appreciate all insight and guidance to best practice.

  Read the article

• AuthBasicProvider: failover not working when the first LDAP is down?

  - by quanta

  I've been trying to setup redundant LDAP servers with Apache 2.2.3. /etc/httpd/conf.d/authn_alias.conf <AuthnProviderAlias ldap master> AuthLDAPURL ldap://192.168.5.148:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> <AuthnProviderAlias ldap slave> AuthLDAPURL ldap://192.168.5.199:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> /etc/httpd/conf.d/authz_ldap.conf # # mod_authz_ldap can be used to implement access control and # authenticate users against an LDAP database. # LoadModule authz_ldap_module modules/mod_authz_ldap.so <IfModule mod_authz_ldap.c> <Location /> AuthBasicProvider master slave AuthzLDAPAuthoritative Off AuthType Basic AuthName "Authorization required" AuthzLDAPMemberKey member AuthUserFile /home/setup/svn/auth-conf AuthzLDAPSetGroupAuth user require valid-user AuthzLDAPLogLevel error </Location> </IfModule> If I understand correctly, mod_authz_ldap will try to search users in the second LDAP if the first server is down or OpenLDAP on it is not running. But in practice, it does not happen. Tested by stopping LDAP on the master, I get the "500 Internal Server Error" when accessing to the Subversion repository. The error_log shows: [11061] auth_ldap authenticate: user quanta authentication failed; URI / [LDAP: ldap_simple_bind_s() failed][Can't contact LDAP server] Did I misunderstand?

  Read the article

• MYSQL - Multiple set values in one update statement [migrated]

  - by Maurzank

  MYSQL - MULTIPLE SET VALUES IN ONE UPDATE STATEMENT USING 2 TABLES AS REFERENCE AND STORING VALUES IN ONE OF THOSE TABLES WITH A SPECIFIC LOGIC. Hello people, A problem came up by making an UPDATE. The example issue is as follows: CURRENUSRTABLE +------------+-------+ | ID | STATE | +------------+-------+ | 123 | 3 | | 456 | 3 | | 789 | 3 | +------------+-------+ HISTORYTABLE +------------+------------+-----+ | ID | TRDATE | ACT | +------------+------------+-----+ | 123 | 2013-11-01 | 5 | | 456 | 2013-11-01 | 5 | | 789 | 2013-11-01 | 5 | | 123 | 2013-11-02 | 4 | | 456 | 2013-11-02 | 4 | | 789 | 2013-11-02 | 4 | | 123 | 2013-11-03 | 3 | | 456 | 2013-11-03 | 3 | | 789 | 2013-11-03 | 3 | +------------+------------+-----+ I'm using these variables: @BA=3, @DE=5, @BL=4, What I'm trying to do is an update on CURRENUSRTABLE.STATE using HISTORYTABLE.ACT with the following logic: STATE value will be updated as ACT value, except when STATE value is 4 and ACT is 3, then STATE will be 5 I made this statement: UPDATE CURRENUSRTABLE RIGHT OUTER JOIN HISTORYTABLE ON HISTORYTABLE.ID=CURRENUSRTABLE.ID SET CURRENUSRTABLE.STATE= ( SELECT CASE HISTORYTABLE.ACT WHEN @DE THEN @DE WHEN @BL THEN @BL WHEN @BA THEN CASE CURRENUSRTABLE.STATE WHEN @BL THEN @DE ELSE @BA END END ORDER BY HISTORYTABLE.TRDATE,FIELD(HISTORYTABLE.ACT,@DE,@BL,@BA) ) WHERE HISTORYTABLE.TRDATE BETWEEN '2013-11-01' AND '2013-11-01' I'm intentionally using "RIGHT OUTER JOIN" and "HISTORYTABLE.TRDATE BETWEEN" because I'd like to change the values in CURRENUSRTABLE using a timeframe of more than one day. If I execute this statement many times using only one day (i.e. "BETWEEN '2013-11-01' AND '2013-11-01'" and then "BETWEEN '2013-11-02' AND '2013-11-02'"... etc ) it works perfectly, but if it is executed using the dates "BETWEEN '2013-11-01' AND '2013-11-03'" the results on CURRENUSRTABLE.STATE are 3, which is wrong, it should be 5. I think the problem relies on "CASE CURRENUSRTABLE.STATE" when uses "HISTORYTABLE.TRDATE BETWEEN '2013-11-01' AND '2013-11-03'", because it reads the STATE 9 times which has not been commited yet until the statement ends. Query OK, 9 rows affected (0.00 sec) Rows matched: 9 Changed: 9 Warnings: 0 Maybe the solution is very simple, but unfortunately I've not much practice on MySQL since I've worked with it less than 2 months :) Is there any suggestions to solve this issue? PD: MySQL version is 4.1.22, I know is very old an EOL, unfortunately I have to make these statements on this version. Thanks!

  Read the article

• duplicity fail: not promping for password: "Running 'sftp user@host' failed"

  - by Thr4wn

  I have two linode VPS accounts and I want to back up one onto the other (the reasons are mainly for fun and to practice server administration.) the short version Duplicity isn't even asking for my password, but immediately says "invalid SSH password" (but I can ssh into the other server). why? the long version When I run duplicity /home/me scp://[email protected]//root/backup I get Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) Invalid SSH password Running 'sftp [email protected]' failed (attempt #2) Invalid SSH password Running 'sftp [email protected]' failed (attempt #3) And it says Invalid SSH password immediately with no opportunity for me to actually type the password. When I type duplicity full -v9 --num-retries 4 /home/me scp://[email protected]//root/backup I get Main action: full Running 'sftp [email protected]' (attempt #1) State = sftp, Before = 'Connecting to 97.107.129.67... [email protected]'s' State = sftp, Before = '' Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) I can ssh into [email protected] fine, and in fact have the ip in known_hosts before I tried any of this. serer 1 (from which I'm running the duplicity command) is Linode's default Ubuntu 8 setup with only a handful of programs installed via apt-get. server 2 (represented by x.x.x.x) is literally only Linode's default Ubuntu 8 setup I previously tried using SystemImager -- would that have changed settings in a destructive way? (I have removed and rebooted since then) Isn't Duplicity supposed to prompt for password? Am I using it wrong? are there common mistakes/dependencies I need to know about? Is there any way that x.x.x.x could be setup that could make this not work (I used Linode's default Ubuntu 8 setup and barely )?

  Read the article

< Previous Page | 719 720 721 722 723 724 725 726 727 728 729 730  | Next Page >