Search Results

Search found 27428 results on 1098 pages for 'copy local'.

Page 726/1098 | < Previous Page | 722 723 724 725 726 727 728 729 730 731 732 733  | Next Page >

• Why has my internet speed dropped down?

  - by Door Knob

  I recently switched to Ubuntu. I've been having a lot of internet troubles ever since. I used Windows 7 before. I've had trouble loading web pages, and it would take a solid minute or two to even start displaying anything. Why is this? How can I fix this? Details: Ubuntu 14.04 ifconfig: eth0 Link encap:Ethernet HWaddr f0:4d:a2:2c:59:42 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:21 Memory:f7ae0000-f7b00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:785 errors:0 dropped:0 overruns:0 frame:0 TX packets:785 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:70511 (70.5 KB) TX bytes:70511 (70.5 KB) wlan0 Link encap:Ethernet HWaddr 14:da:e9:b0:9d:66 inet addr:192.168.2.12 Bcast:192.168.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11979 errors:0 dropped:0 overruns:0 frame:0 TX packets:10503 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13659505 (13.6 MB) TX bytes:1449698 (1.4 MB) Here's a comparison: Speedtest on my phone: Speedtest on my PC: Taken about 30 seconds apart.

  Read the article

• Weird execution of ruby/git executables in Windows

  - by Frexuz

  Something strange has happened. I can't run some command line executables in Windows anymore. Steps: Open cmd Run an executable, such as ruby -v or git -h When I do that, a new command prompt opens, running that command (I think, it's too fast to see), and instantly closes again. I've managed to print screen the new command prompt, and it shows that it's running inside this path: C:\Documents and Settings\Administrator\Local Settings\Temp\3582-490 Inside this folder, is the executable I'm tring to run. If I run ruby, then ruby.exe is in there. If I run git, then git.exe is in there. And it's always emptying the folder in between, so there is always just one .exe file

  Read the article

• What You Said: How You Sync and Organize Your Bookmarks

  - by Jason Fitzpatrick

  Earlier this week we asked you to share your favorite techniques for synchronizing and organizing your browser bookmarks. Now we’re back to highlight the most popular techniques, tricks, and services. By far and away, Xmarks was the most frequently mentioned service. For the unfamiliar, Xmarks is a bookmark syncing service that is packed with features. Not only does Xmarks sync bookmarks between browsers and/or computers it also supports iOS, Android, and BlackBerry (mobile integration requires an upgrade to the premium account). In addition to syncing the bookmarks it also integrates with your search results so you can see how other Xmarks users have ranked sites within your search results. Steve-O-Rama highlights one of the many benefits of Xmarks: Xmarks seems to do the job for me. I’ve got a handful of machines, each with three or four browsers; over the years, I’ve accumulated thousands of bookmarks, stretching across many areas of interest. Trying to keep them all straight had been quite a struggle until Xmarks came along. I freaked out when the company was acquired by LastPass, but was subsequently relieved when they continued the free service. Xmarks has a very nice web interface to access, export, search, organize, and do many other things with your bookmarks. In this way, even if I’m on the go, I can access every bookmark I’ve made. Even so, I still make occasional local backups, directly from the browsers to a network folder. Delicious bookmarks, another veteran of the bookmark syncing services, had a fair number of supporters among the HTG readership. Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone How To Migrate Windows 7 to a Solid State Drive Follow How-To Geek on Google+

  Read the article

• Remembering sharepoint password in Internet Explorer 8

  - by enableDeepak

  I am using IE8 to open a sharepoint portal on local network. Initially, I clicked on remember password after passing domain credentials. However, now I want sharepoint to ask credentials again. I've tried many options - Deleted all cookies, IE Security Tab Form Autocomplete Deleted everything. Restarted my machine. And all I could do. Still, when I open portal, sharepoint logs me in automatically. What should I do to make IE ask for credentials again?

  Read the article

• Unix: Sync directory with FTP or SFTP directory

  - by Svish

  I have a website on my local computer running Mac OS X. I am wondering if there is any built-in command that I can run in the Terminal that will upload that website to my webserver either through FTP or, if possible, SFTP. Installing new commands through MacPorts is also a possibility. A big bonus would be that it only uploaded the files that needs to be updated and not everything else. It would also be nice if I can tell it to delete the files on the server that no longer exists locally once in a while. Any good tips?

  Read the article

• How do I stop CRM from asking for admin credentials when printing report

  - by Ac0ua

  Problem: When printing a report in CRM, I am asked by the UAC for admin credentials. There is a long URL: https://(crm_hostname)/reserved.ReportViewerWebcontrol.axd?ReportSession=(ID)ControlID=(ID)Culture=1333&UICulture=1033&ReportStack=1&OpType=PrintCab Info: There are three users that have the issue laied out here. They are not admins of any kind. It looks like it is asking for permission to allow SQL Server Reporting Services 2008 to run. When I put my credentials in, it just brings up the Print dialog box (this is fine, just stop asking for credentials). I know this might sound silly but I downloaded and installed "SQL Server Reporting Services 2008" hopping my credentials would give permission right from the beginning. Giving the users local admin, I was told is not an option. Note: I did post this on community (dot) dynamics (dot) com but, they are not a very active website. Thanks for any help even if it just points me in the right direction!

  Read the article

• Ubuntu 12.04 Faster boot, Hibernate & other questions

  - by Samarth Shukla

  I've recently started exploring Ubuntu (my 1st distro). I fresh installed precise without a swap (4GB ram). The only issues are, slow boot (regardless of the swap) and instability after a few days of installation. The runtime performance is immaculate otherwise. Even though not needed, I still set swappiness = 10. I've tried the quiet splash profile to GRUB; already have preload installed. But it still is pretty slow. I am not too confident on recompiling the kernel yet. But you could please advice me on that too. I've also added the following to fstab: #Move /tmp to RAM: tmpfs /tmp tmpfs defaults,noexec,nosuid 0 0 (Also if you could please tell me the exact implication/scope of this tweak on physical ram & the swap.) But nothing has happened really. So what alternatives are there to make it boot faster? Also, right after fresh install, though no swap partition, the system still showed /dev/zram0 of arond 2GB which was never used (probably because of the above fstab edit). Finally, I experimented with Hibernate a little, but many claim that it doesn't work on 12.04. (Not to mention, I made a swap file of 4GB for it). What I did was: sudo gedit /var/lib/polkit-1/localauthority/50-local.d/hibernate.pkla Then I added the following lines, saved the file, and closed the text editor: [Re-enable Hibernate] Identity=unix-user:* Action=org.freedesktop.upower.hibernate ResultActive=yes I also edited the upower policy for hibernate: gksudo gedit /usr/share/polkit-1/actions/org.freedesktop.upower.policy I added these lines: < allow_inactive >no< /allow_inactive > < allow_active >yes< /allow_active > But it did not work. So is there an alternate method perhaps that can make it work on 12.04?

  Read the article

• Design pattern to handle queries using multiple models

  - by coderkane

  I am presented with a dilemma while trying to re-designing the class structure for my PHP/MySQL application to make it more elegant and conform it to the SOLID principle. The problem goes like this: Let as assume, there is an abstract class called person which has certain properties to define a generic person, such as name, age, date of birth etc. There are two classes, student, and teacher, that implements this abstract class. They add their own unique properties to it. I have designed all the three classes to include all the operational logic (details of which are not relevant in context of the question). Now, I need to create views/reports/data grids which contain details from multiple classes, for example, say, a list of all students doing projects in Chemistry mentored by a teacher whose name is the parameter to the query. This is just one example of a view, there are many different views in the application, which uses data from 3-4 tables, and each of them have multiple input parameters to generate them. Considering this particular example, I have written the relevant query using JOIN and the results are as expected and proper, now here is the dilemma: Keeping in mind the single responsibility principle, where should I keep this query? It does not belong to either Student class, or Teacher class or any other classes currently present. a) Should I create a new class, say dataView class, and design it as a MVC pattern and keep the query there? What about the other views? how do they fit in this architecture? b) Should I not keep the query in code at all, and make it DB View ? c) Am I completely wrong in the approach? If so what is the right approach? My considerations are as follows: a) should be easy to add new views later on if requirement comes, without having to copy-paste-modify code b) would like to make it as loosely coupled as possible so that if minor db structure changes happen, it does not break I did google searches on report design and OOP report generators, but all the result seem to focus on the visual design of the report rather than fetching the data. I have already taken care of the visual aspect of the report using MVC with html templates. I am sure this is a very fundamental problem with known solution, but I am somehow not able to find it (maybe searching with wrong keyword). Edit1: Modified the title to make it more relevant Edit2: The accepted answer got me thinking in the right direction and identify my design flaws, which eventually led me to find this question and the solution in Stack Overflow which gave me the detailed answer to clear the confusion.

  Read the article

• nodejs server hanging from time to time

  - by Johann Philipp Strathausen

  I have a node server (0.6.6) running an Express application, along with Mongoose and s3, on an Ubuntu 11.04 machine. Several times per hour, the server is hanging. That means that the application is working fine, I see the express loggings, and then all of a sudden the server stops responding. No errors, no traces, no loggings, and strangely enough the browser won't show the request even in the network debugging window. From any machine in the local network it's the same behaviour. I restart the server and it's okay again for several minutes, then again starts to hang, everytime while doing something different. The same application on Amazon on the same Ubuntu version works fine and never hangs. I know all this is kind of vague, but I don't know where to start. Has any of you seen something like this before? Any idea?

  Read the article

• Do you know how to move the Team Foundation Server cache

  - by Martin Hinshelwood

  There are a number of reasons why you may want to change the folder that you store the TFS Cache. It can take up “some” amount of room so moving it to another drive can be beneficial. This is the source control Cache that TFS uses to cache data from the database. Moving the Cache is pretty easy and should allow you to organise your server space a little more efficiently. You may also get a performance improvement (although small) by putting it on another drive.. Create a new directory to store the Cache. e.g. “d:\TfsCache\” Figure: Create a new folder Give the local TFS WPG group full control of the directory   Figure: You need to use the App Tier Service WPG In the application tier web.config (~\Application Tier\Web Services\web.config) add the following setting (to the appSettings section). Figure: The web.config for TFS is stored in the application folder <appsettings> ... <add value="D:\" key="dataDirectory" /> ... </appsettings> Figure: Adding this to the web.config will trigger a restart of the app pool Figure: Your web.config should look something like this The app pool will automatically recycle and Team Web Access will start using the new location.  If you then download a file (not via a proxy) a folder with a GUID should be created immediately in the folder from #1.  If the folder doesn’t appear, then you probably don’t have permissions set up properly.

  Read the article

• Do you know how to move the Team Foundation Server cache

  - by Martin Hinshelwood

  There are a number of reasons why you may want to change the folder that you store the TFS Cache. It can take up “some” amount of room so moving it to another drive can be beneficial. This is the source control Cache that TFS uses to cache data from the database. Moving the Cache is pretty easy and should allow you to organise your server space a little more efficiently. You may also get a performance improvement (although small) by putting it on another drive.. Create a new directory to store the Cache. e.g. “d:\TfsCache\” Give the local TFS WPG group full control of the directory Figure: You need to use the App Tier service WPG In the application tier web.config (~\Application Tier\Web Services\web.config) add the following setting (to the appSettings section). <appsettings> ... <add value="D:\" key="dataDirectory" /> ... </appsettings> The app pool will automatically recycle and Team Web Access will start using the new location.  If you then download a file (not via a proxy) a folder with a GUID should be created immediately in the folder from #1.  If the folder doesn’t appear, then you probably don’t have permissions set up properly.

  Read the article

• There's IP but can't reach gateway

  - by icky

  I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

  Read the article

• Error with Internationalization extension while compiling php 5.4.8

  - by Umakant Patil

  I downloaded latest php version from php.net i.e. PHP 5.4.8 I configured it with following command ./configure --with-apxs2=/usr/local/apache2/bin/apxs --with-mysql --enable-intl --with-libdir=lib64 --with-pear --with-mcrypt --with-mhash --enable-mbstring --with-iconv --with-icu-dir=/usr --with-gettext --with-curl --with-mysqli --with-freetype --with-gd --with-curlwrappers --with-jpeg-dir=/usr --with-png-dir=/usr After this I run 'make' which start building / compiling PHP. After some time It throws me error ext/intl/.libs/php_intl.o: In function `zm_startup_intl': php-5.4.8/ext/intl/php_intl.c:651: undefined reference to `spoofchecker_register_Spoofchecker_class' php-5.4.8/ext/intl/php_intl.c:654: undefined reference to `spoofchecker_register_constants' collect2: ld returned 1 exit status make: *** [sapi/cli/php] Error 1 Spent lots of hours finding solutions. I can't come out of any. Does anyone know what this error exactly means? How to get rid of this error?

  Read the article

• hosts.deny not working

  - by Captain Planet

  Currently I am watching the live auth.log and someone is continuously trying the brute force attack for 10 hours. Its my local server so no need to worry but I want to test. I have installed denyhosts. There is already an entry for that IP address in hosts.deny. But still he is trying the attacks from same IP. System is not blocking that. Firstly I don't know how did that IP address get entered in that file. I didn't enter it, is there any other system script which can do that. hosts.deny is sshd: 120.195.108.22 sshd: 95.130.12.64 hosts.allow ALL:ALL sshd: ALL Is there any iptable setting that can override the host.deny file

  Read the article

• A "tinkered" PC can ping by IP, not by hostname. How to fix?

  - by aitchnyu

  Like this: root@tis-server:~# ping www.google.com ping: unknown host www.google.com root@tis-server:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=55 time=50.3 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=55 time=65.4 ms It was tinkered by somebody else and I (and him!) cant trace his actions. The graphical connection manager also refuses to work thanks to the tinkering. It also makes route add default gw 192.168.0.1 necessary for each reboot to atleast ping by IP. How do I fix this? It is Ubuntu 11.10 As requested: Output of ifconfig: eth0 Link encap:Ethernet HWaddr 48:5b:39:ae:21:98 inet addr:192.168.0.100 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feae:2198/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13194 errors:0 dropped:0 overruns:0 frame:0 TX packets:5156 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1420596 (1.4 MB) TX bytes:827295 (827.2 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4817 errors:0 dropped:0 overruns:0 frame:0 TX packets:4817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:377732 (377.7 KB) TX bytes:377732 (377.7 KB) Output of resolv.conf: Output of /etc/network/interfaces: GNU nano 2.2.6 File: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0

  Read the article

• Safari proxy bypass for IPv6

  - by rhi

  I'm a first-time n00b on Mac (but have been doing computers since before PC's). This Mac has 2 VLANs, vlan0 in IPv4, vlan1 in IPv6. Safari can surf via IPv4 squid proxy OK. Safari can surf via IPv6 natively, if I switch off the proxy. How do I set up the Settings - Network - Interface - Advanced - Proxies to "bypass" IPv6? Current Settings include variations along the lines of ... "*.local, 10.0.0.0/8, 192.168.0.0/16, 172.16.0.0/12 , ::, ipv6 " but don't work as expected. I want Safari to go out on its own with IPv6, not crash at the proxy with "malformed URL" Thanks, //rhi

  Read the article

• VPN trace route

  - by Jake

  I am inside an Active Directory (AD) domain and trying to trace route to another AD domain at a remote site, but supposedly connected by VPN in between. the local domain can be accessed at 192.168.3.x and the remote location 192.168.2.x. When I do a tracert, I am suprised to see that the results did not show the intermediate ISP nodes. If I used the public IP of the remote location, then a normal tracert going through every intermediate node would show. 1 <1 ms <1 ms <1 ms 192.168.3.1 2 1 ms <1 ms <1 ms 192.168.3.254 3 7 ms 7 ms 7 ms 212.31.2xx.xx 4 197 ms 201 ms 196 ms 62.6.1.2xx 5 201 ms 201 ms 210 ms vacc27.norwich.vpn-acc.bt.net [62.6.192.87] 6 209 ms 209 ms 209 ms 81.146.xxx.xx 7 209 ms 209 ms 209 ms COMPANYDOMAIN [192.168.2.6] Can someone explain how does this VPN tunnelling works? Does this mean VPN is technically faster than without?

  Read the article

• WouldISurviveANuke Assesses Your Distance From Nuclear War Strike Sites

  - by Jason Fitzpatrick

  WouldISurviveANuke is a morbid Google Maps mashup that plots out the effective radius of nuclear weapons on major metropolitan areas, your distance from them, and your chances of survival. Visit the site, plug in your zipcode, and set the parameters (how big of a nuclear weapon and how large the nearest target city needs to be) to find out if you’re in the blast radius. We plugged in a downtown address in Detroit, MI. The verdict? Neither we nor the cockroaches will be coming out alive. If you plug in a location far enough away from the direct blast radius you’ll also get a quality of life report that spells out the effects of a local nuclear strike. As far as startling anti-nuclear proliferation arguments go, WouldISurviveANuke is an effective and interactive demonstration. Hit up the link below to try it out. WouldISurviveANuke [via Y! Tech] How to Run Android Apps on Your Desktop the Easy Way HTG Explains: Do You Really Need to Defrag Your PC? Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone

  Read the article

• Problem connecting to MySQL with zend

  - by wheresrhys

  I've set up a virtual host on my local machine (windows xp with xampp installed), have installed zend there and am now trying to connect to the MySQLdatabase. I get the following error message: Message: SQLSTATE[HY000] [2003] Can't connect to MySQL server on ''myhost.com'' (10060) All the tips I've found via google haven't helped. I use kaspersky antivirus and have added port 3306 to the allowed list for MySQL and Apache. I've also pinged myhost.com:3306 and get a response (with ip address 67.63.50.51), though localhost:3306 and 127.0.0.1:3306 aren't found. I've checked that other apps can still access MySQL if the virtual host is pointed at them instead and my non zend apps do work. I guess I have to do something further to the port, or maybe force the app to use a different port, but am not sure how to do either. Any help appreciated.

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• Can't install alternate CD from USB?

  - by mattias

  Hi im trying to install ubuntu 12.04 with full hard disk encryption. After downloading and installing the Ubuntu live CD, I learned that truecrypt doesnt support full disk encryption on linux. I also learned that the best way to get "nearly full disk encryption" on ubuntu is by installing it from the alternate install CD. I tried that, but something is wrong with my CD reader/burner so it doesnt boot up when i insert the cd. My thought here was to take the .iso that I downloaded on my unencrypted Ubuntu system, use Unetbootin to make the usb drive. The usb drive used for this is exactly the same brand as one that I know has worked with a previous ubuntu live system on the same computer. I also used unetbootin for that usb, but I created it from windows that time. The usb stick boots up fine and i get through the first couple of steps in the installation process. However, After a while I get a "box" with the following error message "Load Installer components from CD" There was a problem reading data from the CD-ROM. Please make sure it is in the drive. If retrying does not work, you should check the integrity of your CD-ROM. "Failed to copy file from CD-ROM. Retry? " Then I cant get any further. I googled a lot and found this page which seems to tackle this very problem: http://www.dotkam.com/2010/11/29/ins...mage-from-usb/ I tried to do what it said. After pressing TAB, I wrote : cdrom-detect/try-usb=true without quotes because that's what i think is right. When I press TAB, there already is a text saying : /ubnkern initrd=/ubninit vga=788 -- quiet which can be removed. I have tried to both delete the text before the "--" and just inserting cdrom-detect/try-usb=true before it. Any idea of what can be wrong? I would like to do a full system encryption, or as full as it is possible. I dont want to just encrypt my /home folder. Maybe this isn't the easiest way. I use SanDisk usb sticks. I know there is a problem with U3 launcher on some SanDisks, but I never had to remove U3 before from similar disks, and the alternate install does boot up, so I dont think using U3 removal would help me. Any help or indication to an easier way to do this would be appreciated

  Read the article

• Domain Computers Not Listed In Network

  - by Giawa

  Our network computers are all connected to a domain, and I can see them if I search the active directory (I can click 'search active directory' and then select 'computers' and then Find Now, and all of the computers will appear). However, the computers are not listed in the network browser on any of our computers (Win XP, Win7, Linux, etc) which are connected to the domain. DC is running Windows Server 2008 (Windows Server Standard) with a configured DNS and DHCP server. All of the IPs on our local network are static IPs, although I can't see how that would make a difference. I can still connect to computers on the network via \\computer_name, but I cannot browse them in 'network' or in 'my network places'. The computer browser service is not started on the DC, but I tried starting that and it had no effect. DC currently has the firewall configured as 'off' to try to debug this problem. Thanks in advance

  Read the article

• Can't change permission/ownership/group of external hard drive on Ubuntu.

  - by MikeN

  I have an external hard drive connected to my Linux box. I wanted to setup a web server to access files on it, but the permission on all files and directories on the drive are "rwx" for the owner which is my local login, and the group is the "root" group. I need the files readable by the apache user, I was trying to set all files to be "chmod a+rwx -R *", but this doesn't do anything (gives no errros, just has no effect.) I tried chaning the group using "chgrp" to my user group, but that won't work either, it gives me errors that I lack permission even when I run all those commands as sudo! What's up with this hard drive??? "sudo chmod a+rwx *" should work on anything, right?

  Read the article

• IE Sessions in Terminal Server

  - by Jacob

  Currently we are using WADE middleware for our order processing operation. We have about 40 operators that use 1 terminal server to open IE 8 to access the WADE middleware. To me, it's random, but every now and then someone will come to me and tell me that IE has a "Page cannot be displayed" or "HTTP Error 500" error. I did a bit of testing on my local machine and I never get this error while doing normal operations. Although, when I open one session with username "test" and then login to the wade admin console as admin, I run into problems. I do not run into problems until I logout of the wade admin. Once I logout of the Wade admin, my "test" session says "page cannot be displayed". This makes me think the IE user sessions on the terminal service are cross talking. Does anyone have any possible settings I can change in IE or do you think this is an issue with the middleware? The Terminal Server is Windows 2003, btw.

  Read the article

• No response from example.com using Apache

  - by stevens-G

  I am unable to access example.com or by local IP after restarting the server. I checked to make sure httpd service was on. I looked at the error_log in /var/log/httpd and found nothing. Tried to restart httpd again and it says 'Ok'. I'm not sure where else to check. I did move DocumentRoot from /var/www to /web-root and it worked before restarting the server. I tried pointing it back to /var/www and still not able to view the page. IPtables have not changed. Any suggestions?

  Read the article

< Previous Page | 722 723 724 725 726 727 728 729 730 731 732 733  | Next Page >