Search Results

Search found 20045 results on 802 pages for 'reporting services 2005'.

Page 727/802 | < Previous Page | 723 724 725 726 727 728 729 730 731 732 733 734  | Next Page >

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Is 40+ Logons on Exchange 2003 per user normal?

  - by cbsch

  Hello! We've had a problem at work where users sometimes randomly can't connect to exchange. I've found out that it's because they reached the limit of 32 concurrent logons. I increased the maximum allowed connections by adding the key "Maximum Allowed Sessions Per User" in HKLM\SYSTEM\CurrentControlSet\Services\MSExchangeIS\ParametersSystem. But I'm not sure if this is a real good fix. Looking at the logons some users has as many as 15 logons with the exact same logon time. I know for sure that Outlook 2007 does this, as I was watching them while a user connected with Outlook after a restart on the Exchange service. Every user also has an iPhone connected to exchange, I don't know if these cause the same thing. Is this normal? Could there be a bug in the software? (The Outlook 2007 has nothing configured, except added the user, pure vanilla installs). The users are mobile, and when Outlook generates up to 15 connection every time it connects, and I've read (no sources, sorry) that Outlook doesn't time out connections before 2 hours. I might have to set this number real high to prevent it from being a problem.

  Read the article

• OSX server setup suggestions

  - by Tom

  I am looking into the possibility to setup an OSX server for my employees, and would like some input on what is the best approach to meet my needs, and perhaps some suggestions if I am moving in the wrong direction. I am thinking of a Mac Mini OSX server, and are not sure if my needs will be met, and what possibilities are out there. I want these capabilities: - Groups/Users managed on server - Shared folders and private folders for users/groups - Access to activated services - Server hosting software for the users (developing tools ++) - Similar to Windows Terminal Server - Virtual desktop environment (both local and over internet/VPN) - Possible to access trough Mac and Windows The reason I am looking at OSX server is that my employees almost only work in OSX environment, and I want to offer the capabilities to logon to the server trough some kind of terminal software, and have full access to their work OSX environment and software on their mac or pc, from anywhere they might be. Instead of having to have multiple setups and need for spending alot of time installing and setting up needed software on every client. This is a small business, where some work on local network, and others from the internet, preferably trough VPN. But a terminal server solution, that are fast and easy to manage would be perfect for our needs. So if anyone have any experience with a similar setup, please let me know what you did, and your experiences with your setup.

  Read the article

• Troubleshooting DTCPing Errors

  - by JimmyP

  So I am running DTC ping between 2 machines on our network and am getting the following error ++++++++++++++++++++++++++++++++++++++++++++++ DTCping 1.9 Report for WEB2 ++++++++++++++++++++++++++++++++++++++++++++++ RPC server is ready ++++++++++++Validating Remote Computer Name++++++++++++ 03-03, 13:39:45.099-->Start DTC connection test Name Resolution: internal-->10.20.3.236-->internal.something 03-03, 13:39:45.114-->Start RPC test (WEB2-->internal) Problem:fail to invoke remote RPC method Error(0x6BA) at dtcping.cpp @303 -->RPC pinging exception -->1722(The RPC server is unavailable.) RPC test failed I have also run RPC ping where I get what I beleive is the same error: C:\Program Files\Windows Resource Kits\Tools>rpcping -s internal Exception 1722 (0x000006BA) Number of records is: 4 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 1722 Detection location is 323 Flags is 0 NumberOfParameters is 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 1237 Detection location is 313 Flags is 0 NumberOfParameters is 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 10060 Detection location is 311 Flags is 0 NumberOfParameters is 3 Long val: 135 Pointer val: 0 Pointer val: 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 10060 Detection location is 318 Flags is 0 NumberOfParameters is 0 I'm pretty sure that the exception number 1722 is the key but I can't find any info about it. There may be a firewall with ports that need opening between the machines which I am checking with our sys admins now. But I can do a regular ping between the machines. Other than that I am reading a lot of articles talking about OS services and components I know nothing about and am having trouble finding any info on. Can anyone shed any light on this? FYI the machine is running Windows Server 2003 RS SP2.

  Read the article

• Protocol (or service publish/discovery) to detect devices in network

  - by Gobliins

  we connect some embedded devices in a network. What i am looking for now, is a way to find the devices IP and identify them. We work with Windows PC´s and i am about to write a C# tool that should do this. I thought about send a udp broadcast and in the ack i.e. is the device´s ip, which would mean the device needs a daemon runnig to assign an ip itself. Running a service (like a printer) on the device, and on the PC just lookup for the service. I read about some things like apipa, zeroconf, ipv4 local link, bonjour, dns-sd, mdns, bonjour; They can automatically assign ip´s and publish services in a network. My Question is, can someone recommend me what would be good for my task? -The protocol or Service should be low on ressource (memory/cpu usage) use. -Are there some standard protocolls to use? -Is DNS a good idea or would it be to ressource consumpting just for finding a device´s IP? -Should also work when no dhcp servers are around. edit: To clarify a bit: The IP configuration is automatic. The problem to focus is how to tell the PC which IP in the network (or a direct connection in this vase there would only be one) belongs to the device (identity).

  Read the article

• Query specific nameserver for a particular domain upon VPN connect

  - by MT

  Some background: I have a work laptop with Ubuntu 9.10 on it. I have a small network at home where I've been running some basic services (for myself/my family) for 10 some years. In my home network there is a nameserver (Fedora) running Bind 9 with two "views". One view is the "outside" view and it provides name resolution (to the Internet at large) for email, a wiki, and a couple of blogs. The "inside" view provides name resolution (to the internal RFC1918 addresses of theses servers) as well as all the inside hosts, network equipment, ...etc. I connect with an openvpn client to my home network from outside (such as work). What I'd like to be able to do is resolve names on my internal network across this VPN (so I get the RFC1918 "inside" responses) without fully changing my resolver to the DNS server at my hose. For example, if I connect to the VPN from work, I can change my resolver (by editing resolv.conf) to the DNS server at my house (across the VPN) and then successfully resolve all of the inside DNS names on my home network. The issue I have with this is that now I'm no longer able to resolve "inside" names provided by my work's DNS servers (because I'm using my home DNS server). Alternatively, I can connect to the VPN and access my home severs via IP addresses directly, but this is inconvenient and causes issues with Apache name-based hosting (among other things). In the end, the effect I'm trying to achieve is as follows: When I connect to the VPN I automatically start sending DNS requests for *.myhomedomain.com to my home nameserver, but any other requests continue to go the the nameserver I was using before (the one I received on my company LAN via DHCP). When I disconnect the VPN, requests for *.myhomedomain.com go back to the local LAN DNS server (e.g. all requests are going there now). I'm looking for suggestion at to how this can be accomplished.

  Read the article

• How do I know if I managed to completely remove an undetected trojan?

  - by ubuntuisbetter

  I catched a trojan that uses explorer.exe to reproduce itself in case of deletion of its autostart entry or main exe file in Programs/x. It had already tried to contact a suspicious server over explorer.exe, blocked that via my firewall. I: Removed the autostart entries from the registry Looked through my services if there was anything suspicious Deleted the trojan from Programs/ Went through System Volume Information to find a 2 month old explorer.exe and replaced the possibly infected one. There are no suspicious processes running now anymore (no duplicate explorer.exe) and nothing wants to connect this trojan owners sever either. I checked my system with several anti-malware programs too. What the trojan did: Started a second explorer.exe Always when I deleted the main trojan exe file it was reproduced (by the second explorer.exe) Always when I deleted the autostart entry it was reproduced by the explorer.exe too. When I terminated the suspicious explorer.exe, which used only half as much memory as the less suspicious one from Windows, a strange thing that I know from the computers in my Informatics class happened: A window popped up in the top left of my explorer-less desktop, titled "Personal settings for ... are ..." that obviously copied some files. Then both explorer.exes started again and the trojan was everywhere again. What did the trojan actually do to get explorer to rescue it? Is my PC clean of this newish trojan now? What are the other locations I should check for the trojan? The trjoan doesn't seem very high-level, could it have changed other system files or is the autostart entry vital for it? Thanks in advance, Your trojan paranoid friend (Getting linux in a week)

  Read the article

• Windows 7 delayed file delete

  - by GregoryM

  I'm stuck with a pretty rare problem that happens on Windows 7 OS only. Every time I'm deleting the file with *.exe extension through explorer, the file doesn't get deleted immediately. I'm forced to wait for around one-two minutes before the system will delete the file. The main problem is that I cannot develop in such situation, because every time I build my solution, the old executable gets 'deleted', but is still there. So the new one cannot be created by Visual Studio. This problem breaks the Steam update progress and a few other installers functionality too. Fresh installed Win7 doesn't have this kind of trouble, so I guess this must be some bad registry entries or some services. Browsing the internet for solutions I found only this: http://www.sevenforums.com/software/72091-several-minute-delay-when-deleting-any-exe-file.html. But the solution the author found is not working (change the userName :)). Is there any ideas how to find what causes this to happen? BTW: when I place the file into Trash bin, no delay occurs. When I delete file with Total Commander - no delay too. Tech details: Windows 7 x64 Ultimate.

  Read the article

• 1 PC, 2 consoles (as in 2 monitors, keyboards and mice)

  - by ciuly

  I have this desire to "kill 2 birds with one shot". Currently, I have 1 server running round the clock, 1 laptop that runs about 8 hours a day, 7 days a week, and a desktop that runs about the same length of time. All 3 are ... old, to say the least. So there is a great need to upgrade (well, the server might handle its job for another year or so, but that only depends on how much time I have to put it to "work"). Now, I'm "dreaming" of only one PC. I'm thinking vmware's ESX. So there will be a VM for the server, a VM for the "laptop" and one for the "desktop". And obviously I'll have to somehow "link" a set of monitor/keyboard/mouse with one of the laptop/desktop VMs. The server doesn't need such things, obviously (it doesn't have them at this moment either). Is something like this possible? ESX is not a requirement, it's just something I found that answers part of my problems, but there still remains the 2 KVM set that needs connecting and "linking" to appropriate VM. Why I would want to do this? well, first of all, it's much cheaper to upgrade one PC than 3. Then, the power consumption is obviously lower. Plus the extra space.Plus it allows me to better separate networks and services. Thanks.

  Read the article

• 1 PC, 2 consoles (as in 2 monitors, keyboards and mice)

  - by ciuly

  I have this desire to "kill 2 birds with one shot". Currently, I have 1 server running round the clock, 1 laptop that runs about 8 hours a day, 7 days a week, and a desktop that runs about the same length of time. All 3 are ... old, to say the least. So there is a great need to upgrade (well, the server might handle its job for another year or so, but that only depends on how much time I have to put it to "work"). Now, I'm "dreaming" of only one PC. I'm thinking vmware's ESX. So there will be a VM for the server, a VM for the "laptop" and one for the "desktop". And obviously I'll have to somehow "link" a set of monitor/keyboard/mouse with one of the laptop/desktop VMs. The server doesn't need such things, obviously (it doesn't have them at this moment either). Is something like this possible? ESX is not a requirement, it's just something I found that answers part of my problems, but there still remains the 2 KVM set that needs connecting and "linking" to appropriate VM. Why I would want to do this? well, first of all, it's much cheaper to upgrade one PC than 3. Then, the power consumption is obviously lower. Plus the extra space.Plus it allows me to better separate networks and services. Thanks.

  Read the article

• how to build network across buildings ?

  - by Omie

  Hi ! I need some help in building a network between hundreds of computers spread across multiple buildings of my college. Yes, I'll be doing this as a part of my college project. Please see this image, it will give you enough idea of what I'm trying to achieve. http://i.imgur.com/rOohx.png All the computers in all buildings should be able to connect server. Once network is up, there will be a set of services over intranet and network use will be moderate. well, say there will be an email server and a http server. My point is, I cannot afford much of performance loss. It feels easy to connect computers inside 1 building to each other, however, I'm clueless as to how to connect all of them to server. I mean, just 1 cable won't be enough to connect 1 building to server, right ? How should I go with it ? I am not expecting detailed configuration. Just heads up will do :) Thanks

  Read the article

• Online FTP or file sharing service [on hold]

  - by Frede

  We need to share large files with clients, e.g. clients upload a large file, we modify it and later make it available for download. Up until now we've used FTP but this has a number of drawbacks. A lot of management of files and setting up accounts etc. We are therefore considering online alternatives. Requirements: Cheap, 8-) Easy to use, ideally just requiring a web browser, but also possible for power users to connect e.g. via FTPS/SFTP No registration requried for users to upload/download files. We ourselves of course need to be able to login an view uploaded files and upload new files. No per user fee High bandwidth. As files may be GBs in size both upload and download speed cannot be too slow Secure. Encryption during upload/download. No way for users to access uploaded files. Once a user has uploaded a file they (or anyone else besides us) should be able to access the file. To download files users get a link with a password. Ideally the link expires after a set time. No software installation We do NOT need any sync features, backup, versioning etc. Just a quick, easy, secure way for us to share files with our clients. Services like JustCloud, DriveHQ etc seems bloated and "too much" for what we need. What other alternatives exist? Thanks!

  Read the article

• .bat file - Nagios v3.2 service check and start if stopped

  - by LbakerIT

  I'm just barely getting into programming so I do apologize for my ignorance. I'm trying to create a .bat file that will check if a service is running on XP Pro. If service is running it will exit 0. If the service is stopped start service wait 10 seconds (via ping i'm guessing) check if service is running if service is running exit 0 if service is stopped start service wait 10 seconds Do this check a total of 3 times. if service does not come up within that time: exit 2 Exit 0 = ok exit 1 = warning exit 3 = critical (and this will alert) I need to do this for 3 different services but i'm expecting that it would be better to create one per service. That way you get notified on the specific service that is not coming back up. The goal is that if the service stops it will start it. If after 30 seconds it is unable to start the service then it will send an alert. The reason I'm trying to do it with a .bat is this is consistent with all other scripts and I did not want to complicate it further by adding different kinds of code. Yay for consistency! Again I do apologize for my ignorance I've been thrown into this project last minute. Thank you for the help and reading my question!

  Read the article

• Windows-7 Ultimate 64 bit wont connect to my wired/wireless networks

  - by A302

  Windows 7 Ultimate 64 bit. Everything was working fine & then just stopped working. The nic card Realtek PCIe GBE Family Controller is enabled but does not connect to my router (cables & router ports are good). Wireless Atheros AR5007EG is enabled but the connection is limited (encryption type / key have been verified). A laptop running XP can connect both wired / wireless. SSID is not being broadcast, connect to network if it is not broadcasting is checked. Have checked services.msc for Bonjour & did not see it listed. Network & sharing center does not list any active networks. Device manager lists both devices as functioning properly. Router configuration has not been changed. Virus scan has not found anything. I would like to fix this rather than using Acronis to do a system restore. Thanks in advance for any advice offered in solving this. 26 Jan, the nic card & wireless are working using PCLinux OS Live CD. It appears that the problem is Windows 7 related.

  Read the article

• Reverse NAT Setup for Hyper-V on Win 2008 R2

  - by sukru

  I'm trying to setup a Linux server behind a Windows Hyper-V host that will help supply some of the services (SSH, HTTPS, etc). However getting RRAS configured for reverse NAT (port forwarding) turned out to be a non trivial task. As a staring point, I tried forwarding port 22 (SSH) to the virtual machine. The virtual machine is on a public interface (i.e.: it also has a visible IP on the same network as the host). On RRAS management console I tried to add a rule, by adding "Local Area Connection" to NAT pool (Public Interface - Enable Nat), and an incoming rule for port 22 - :22. I also tried with the same port enabled on Windows Firewall (and not). The NAT management page tells there are "1 mappings" and "30+ Outbound packets transleted". However all other counters (Inbound packets translated, and respective rejected ones) are always zero. (I'm trying to access the server from an external machine). I can directly access the service if I give the VM's public IP, but not the host's one. Is there a way to enable this on RRAS?

  Read the article

• How can I assign DHCP leases from a script?

  - by devicenull

  I have an environment where there is one DHCP server servicing a number of different hosts/vlans. The switches are configured to forward the DHCP requests over (via ip-helper) and include information about the port (option 82). I'd like to take that information and translate it into an actual lease for the server. I don't think it's particularly feasible for me to pregenerate a list of available leases, but I should be able to determine an address for a lease as it comes in. Is there an DHCP server that can execute a script when it receives a request? (Note: I'm looking to assign the IP from the script, not have the DHCP server assign an IP then execute the script) Edit: So, ultimately I'm trying to provide DHCP/PXE services over a large number of distinct vlans. This is so we can do OS installs via PXE booting without having to have a separate PXE vlan. I've got the switch config down no problem, and I have the DHCP server recognizing option 82. I need a way to pull DHCP assignments from another system (this other system would know what subnet to use on what vlan), but I do not want to have to pregenerate a list of vlan:DHCP range pairs.

  Read the article

• One Apache server, multiple clients - best practices for config files?

  - by OttaSean

  First time user; please be gentle. :-) (And if you don't like my question I'd be grateful for a comment as to why...) I am doing a contract at a government server shop that provides web services for multiple client groups in other areas of the government. My employer has asked me to look into how other shops, in similar situations, handle configuration files, and whether there are any best practices on the subject. I'm pretty sure there are lots of installations out there running multiple VirtualHosts out of one Apache installation, but surprisingly I couldn't find anything online about how people handle config file layout, so was hoping some of you wise folks on ServerFault might have some thoughts or pointers for me. The current setup - which seems logical to me - is that each client site has its own directory off the root - so: /client/tps-reports/ /client/silly-walks/ /client/ministry-of-magic/ and so on - and each of those directories has a /htdocs, /cgi-bin, and /conf (among others). The main /etc/apache/httpd.conf only contains Include statements (and lots of comments), the last of which is: Include /etc/apache/vhosts/*.conf The vhosts directory contains symlinks: tpsrept.conf - /client/tps-reports/conf/tpsrept.conf sillywk.conf - /client/silly-walks/conf/sillywk.conf mom.conf - /client/ministry-of-magic/mom.conf Each of those .conf files contains the actual NameVirtualHost definition and a gigantic <VirtualHost 192.168.12.34> stanza - which contains all the stuff about the specific site. The idea is that clients have access to what's in their own /client/xx directory, so they can change stuff in the section of the config that is relevant to them. As I mentioned above, that seems fairly logical to me, but I'm wondering if any of you wise folks are aware of potential gotchas with this sort of layout, or any other thoughts on why it is or isn't a good idea. In particular, how do other places do it? Is there a "best practice" for this sort of thing? Many thanks in advance for your time and any thoughts you all might have.

  Read the article

• Server high CPU load issue! ( Cpanel + CentOS 5)

  - by kenby

  Our server cpu load is high todays sometimes reaches to 560! .. We have the lastest Cpanel/whm and the kernel is update!while the load average is : Load Averages: 39.05 75.01 45.33 the apache log is: Current Time: Sunday, 30-Jan-2011 01:50:13 EST Restart Time: Saturday, 29-Jan-2011 21:51:20 EST Parent Server Generation: 2 Server uptime: 3 hours 58 minutes 53 seconds Total accesses: 149493 - Total Traffic: 2.4 GB CPU Usage: u9.17 s10.66 cu42.82 cs0 - .437% CPU load 10.4 requests/sec - 174.6 kB/second - 16.7 kB/request 121 requests currently being processed, 42 idle workers W_WWW.W_..W.W_W_WCWW..W...W.WWW.WWWW.WW.C_W_.W.WW.WC..W.WW.WW .W.W.W...WWWW...WW.CC.C.._W.WC.WW_WW._W....W.WWW.W.WWW.W..W WW.....WW.W_WWWWW..WCRW..WWCW.WWW__.WWWWCW_W._._WW_W...W...W _W..W..WW.W...._W..._WW.W.WWW.._W.WWW.WWW....WW_.C...W._ Scoreboard Key: "_" Waiting for Connection, "S" Starting up, "R" Reading Request, "W" Sending Reply, "K" Keepalive (read), "D" DNS Lookup, "C" Closing connection, "L" Logging, "G" Gracefully finishing, "I" Idle cleanup of worker, "." Open slot with no current process What cause this high cpu load while the apache cpu load is fine? the mysql process is also fine.. the cpu load is still high even if I stop mail-http-mysql services!

  Read the article

• RedStation.com is heaven for ddos attackers, How to file complaint?

  - by Ehsan

  Sorry, I don't know where to open this subject. This is not the first time we have faced with a massive DDOS attack from one of servers in RedStation.com and even after we had contacted with their abuse department with it's log there is no cooperation and they don't even like to bother themselves about it. and we don't know how to stop such activity. Do you know how to file complaint against this datacenter? we could not be patient anymore and see they are not care about such things on their network ? it seems like they are heaven for attackers now since they close their eyes to gain more money. I guess some global organization is missing in this matter to investigate such activity and make sure providers are responsible for their services. Here is some of it's log: 2686M 75G DROP all -- * * 31.3-RedStation 0.0.0.0/0 rt: 16167 0.002007 31.3-RedStation -> my-server-ip UDP Source port: 36391 Destination port: 16167 0.002011 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002014 31.3-RedStation -> my-server-ip UDP Source port: 39585 Destination port: 12081 0.002018 31.3-RedStation -> my-server-ip UDP Source port: 39585 Destination port: 12081 0.002021 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002025 31.3-RedStation -> my-server-ip UDP Source port: 39585 Destination port: 12081 0.002033 31.3-RedStation -> my-server-ip UDP Source port: 36391 Destination port: 16167 0.002037 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002040 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002044 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002047 31.3-RedStation -> my-server-ip UDP Source port: 39585 Destination Any response would be appreciated

  Read the article

• Run as another user, but also as administrator

  - by Tewr

  I am trying to debug a virtual machine (VM) running on a remote computer from my workstation (A). Both VM and A are running Windows 7 Enterprise. Apparently, I need to start the Remote Debugger Service (RDS) on VM as an administrator. Apparently, I also need to run RDS as the user Tewr logged in on A (domain: DOM). VM runs the services i need to debug, as well as the remote desktop interface with an account VMUSER in a domain called VMDOMAIN. I manage to start RDS as administrator, but then the RDS process is owned by VMUSER and that's not good enough. I also manage to run RDS as DOM\Tewr, but then not as an administrator. I have Added DOM\Tewr as an administrator on VM, but thats not good enough becuase the process is still not run as administrator. How can I run the RDS process as DOM\Tewr and "As Administrator", while logged on in windows as VMDOMAIN\VM? (note: I have tried creating an account with the same credentials / password as VMUSER, as hinted in the ms article above, but with no luck...)

  Read the article

• What is the best time to set the IP address for a server headed to a server colocation facility?

  - by jim_m_somewhere

  What is the best time to set the IP address for a server? I have a server that I am going to install the OS on and then I am going to send it to a server colocation facility. The server is going to have Internet facing services (www, email, etc.) I can set up a "fake" IP address during install (by fake I mean private as in RFC 1918) and change the "fake" IPs to the real IPs once I set up the colocation service. The other option is to set up the colocation service...wait for them to give me the "real" IPs and use them during the OS install. The ramification are that...if I use "fake" IPs during install...I will have to wait before I set up things like SSL certs. If I wait for IPs from the colocation provider...then I can set up SSL certs that use the "correct" (as in "real") IP addresses...no changes to the certs until they expire. Do the "gotchas" of changing an IP address on a server outweigh the benefits of a quick install? The other danger with using "fake" IPs is that I could make a mistake when I go through the various files to change the IP address to the "live" IP address. Server OS: CentOS 6.2 or CentOS 6.3, 64 bit. Apps: Apache 2.4.X httpd, MySQL 5.X (will eventually use replication)

  Read the article

• Building a small server farm

  - by RayQuang

  Hi, I am planning to set up a Tech startup company that will provide web application solutions. Eventually we hope to diversify into different areas such as possibly social media or other services. For now we plan on running a high demand (from 1000 to 10,000 users in the first year) website running the application. This includes a MySQL database backend, email, and development servers. My question is then, what type of server arrangement will work best, that is ti say should i have a small cluster of ultra high power machines (E.G. Top of the range Xeons, with 12GB RAM) or will it be better to have more less powerful servers load balanced? Should I go for 1 - 2 u servers rack mounted ot would it be beter for it just to be tower servers for maintainability? Finally I would also like to know what kind of Internet and router i would need, I currently have 10mbit down and barely 1 mbit up, but soon our area will have a fiber optic connection with international speeds of up to 25 mbit / sec. Thanks in advance, RayQuang UPDATE: sorry I forgot to mention it, the platform that I will be using is PHP with the APC code cache, Probably running Debian.

  Read the article

• Incoming traffic while on public network

  - by zvikico

  I'm developing a web app and I need to be able to get incoming traffic from 3rd party services I use. This is a classic webhooks situation: I send a request with a return address and receive the response (via HTTP) some time later to the given address. The simple solution would be to provide my external IP address and forward the incoming traffic from the router to my machine. However, I'm working in a large office and I cannot control the router configuration. I'm looking for a different way to achieve that. I do have servers online. I can have a daemon running on one of those servers, which will handle the incoming traffic. I can run a parallel daemon on my machine, which will keep an open connection with the remote daemon (over ssh preferred) and when an inbound traffic is received by the remote, it will send it to the local, which will send it to the correct port on my machine, as if it was received in the natural way. Is there any ready-made solution for that? PS. I'm on OS X and my server is Ubuntu. Thanks, zvikico

  Read the article

• ionice without effect

  - by tim

  System is Ubuntu 10 LTS 64bit (2.6.35.31), I'm running on xen 4.0, no services active, cron stopped, scheduler is cfq for the disk /usr is mounted from: time find /usr -exec stat {} \; > /dev/null 2>&1 & giving real 0m35.760s user 0m0.270s sys 0m3.910s and time ionice -c3 find /usr -exec stat {} \; > /dev/null 2>&1 & giving real 0m36.110s user 0m0.310s sys 0m4.100s which is exactly as expected, now I run both at the same time: time find /usr -exec stat {} \; > /dev/null 2>&1 & time ionice -c3 find /usr -exec stat {} \; > /dev/null 2>&1 & where to my believe the ioniced version should be much slower while the straight version should be as fast as if running alone. but: straight: real 1m10.430s user 0m0.320s sys 0m3.940s ioniced: real 1m10.230s user 0m0.250s sys 0m4.020s which implies that ionice did not work at all. Any hints?

  Read the article

• Inexpensive (used) hardware for Xen virtualization test?

  - by Jason Antman

  Virtualization is one of the areas where I could really use some experience. I also run quite a few services (web, mail, dns, etc.) out of my home. Since most of my hardware is getting a bit old (I'm running on stuff that was surplused years ago...) I decided that it's about time I start renewing some things, and also play around with virtualization a bit more. My plan is to setup a SAN box (simple iSCSI target, relatively inexpensive gigE switch), get a pair (for starters) of new servers, and start building some new stuff with Xen, specifically planning on playing with live migration and full virtualization. Does anyone have recommendations for used, older "servers" (really anything in a rack-mount form factor, I'm not too worried about things like iLO/iLOM for the test nodes) that support VT-x/AMD-V? I'm biased to HP, but it looks like they didn't make Proliants with VT-x/Vanderpool processors until G6 (for the DL360) or so, which is way out of my price range. I'm looking in the sub-$300 range (or less, if possible), used, probably Ebay. Any recommendations are greatly appreciated. Edit:And, to catch this before the comments start coming - these are personal systems. I have first-generation Proliants still in use (I got them as corporate surplus in 05, they've been running since then, and probably were running since 01 or 02 prior to being sold). I don't need anything shiny and new - I've got a bunch of old boxes, at least one complete replacement for every model in use, and that's fine for me (and easy on the wallet).

  Read the article

< Previous Page | 723 724 725 726 727 728 729 730 731 732 733 734  | Next Page >