Search Results

Search found 20409 results on 817 pages for 'url routing'.

Page 73/817 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• IPv6 connections routed to IPv4 device

  - by Yvan JANSSENS

  I have an IBM 9406-250 with V5R1 and IPv4 only connectivity, and want it to be reachable over IPv6. I cannnot install an IPv6 stack on it, but I want it to be accessible by IPv6 so I can drop the requirement to VPN to my home network. I have an OpenWRT device running, which takes care of the IPv6 routing on my network and the tunnel to SIXXS, and I was wondering if it is possible to assign another IPv6 address to that device, and route it to the IPv4 IBM computer. Which software do I need for this, and how is this technique called?

  Read the article

• Network interface selection

  - by Antonino

  Hello. Suppose I have more than a network interfaces and I want to selectively use them per application. eth0 is the standard interface with the standard gateway in the main routing table eth1 is another interface with a different gateway. Suppose I launch an application as a user "user_eth1". I used the following set of rules for iptables / ip rules. IPTABLES: iptables -t mangle -A OUTPUT -m user --uid-owner user_eth1 -j MARK --set-mark 100 iptables -t nat -A POSTROUTING -m user -uid-owner -o eth1 user_eth1 -j SNAT --to-source <eth_ipaddress> IPRULE: ip rule add fwmark 100 lookup table100 and i build "table100" as follows (no doubts on that) ip route show table main | grep -Ev ^default | while read ROUTE; do ip route add table table100 $ROUTE; done ip route add default via <default_gateway> table table100 It doesn't work at all. What's wrong with this? Thank you in advance!

  Read the article

• Using nginx and/or varnish to cache server-generated 301 redirects

  - by rlotun

  I'm implementing a sort of url-shortener service. What happens is that I have some backend app server that takes in a request, does some computation and returns a 301 redirected url back upstream to an nginx frontend: request ---> nginx ----> app_server What I want to be able to do is cache this returned 301 url for the same request (a specific url with a "short code"). Does nginx do this caching automatically? Or should I drop in something like varnish in between nginx and the app_server? I can easily cache this in memcache, but that would require hitting the app_server, which I'm sure can be dispensed with after the first request. Thanks.

  Read the article

• Two VPN (internet) connections rounting (win2003)

  - by tmp3128

  Here is my setup: - win2003 server (ISA installed) with 3 NICs:   1) internal network   2) ISP 1 (default) network (DHCP enabled)   3) ISP 2 (backup) network (DHCP enabled) - several "normal" PC within internal net - one "special" PC within internal net Both ISP 1 and ISP 2 provide access to internet and their resources thru their VPN connections. The goal is to enable all "normal" PCs to use internet from ISP_1's VPN connection and "special" should use only ISP_2's VPN connection. Futhermore all "normal" and "special" PCs should have access to several servers accesible only thru ISP_2's VPN connection. I have some thoughts how to achieve this but I want to be certain because everything should be configured as quickly as posible, avoiding significant downtime. windows-server-2003 isa routing vpn

  Read the article

• Rewriting a URL for tomcat through an ajp connection

  - by StudentKen

  I've tried several attempts to resolve this, but all have come up naught. Currently I have apache setup to forward all urls at and past the /portal/ tag to tomcat. Unfortunately, tomcat receives these requests through /portal/appName, a subdirectory in webapps rather than the webapps root directory where my wars are deployed. Is there a simple solution to this that I'm not seeing? I've been trying to use mod_rewrite to ^/portal/ $ / but that doesn't yield the expected results (perhaps I'm doing this wrong?).

  Read the article

• Redirect cPanel url to something different

  - by Peter

  I have masterdomain.com which is the domain that hosts other domains. On cPanel normally you can get to the actual cPanel by visiting cpanel.hosteddomainA.com, hosteddomainA.com/cpanel or hosteddomainA.com:2082 What I would like to accomplish is to have the hosteddomains cPanel auto redirect to something like my.masterdomain.com:2082 . Doing this would allow me to adequately throw an SSL cert in my. and really offer a secure experience to my users. I know it's possible because bluehost does the same. They redirect to my.bluehost.com. Can anyone think of how to do it?

  Read the article

• how to rewrite '%25' in url

  - by nn4l

  My website software replaces space characters with '+' characters in the URL, A proper link would look like 'http://www.schirmacher.de/display/INFO/How+to+reattach+a+disk+to+XenServer' for example. Some websites link to that article but somehow their embedded editor can't handle the encoding, so what I see in the httpd log files is actually GET /display/INFO/How%2525252bto%2525252breattach%2525252ba%2525252bdisk%2525252bto%2525252bXenServer which of course leads to a 404 error. It seems that the '+' character is encoded as '%2b' and then the '%' character is encoded as '%25' - several times. Since there are many such references to different pages from different websites, I would like to rewrite the url so that the visitors get the correct page. Here's my attempt which does not work: RewriteRule ^(.*)%25(.*)$ $1%$2 [R=301] What it is supposed to do is: take everything before the %25 string and everything after it, concat those strings with a '%' in between, then redirect. With the example input URL the rule should rewrite to /display/INFO/How%25252bto%2525252breattach%2525252ba%2525252bdisk%2525252bto%2525252bXenServer followed by a redirect, then it should rewrite to /display/INFO/How%252bto%2525252breattach%2525252ba%2525252bdisk%2525252bto%2525252bXenServer and again to /display/INFO/How%2bto%2525252breattach%2525252ba%2525252bdisk%2525252bto%2525252bXenServer and so on. Finally, after a lot of redirects I should have left /display/INFO/How%2bto%2breattach%2ba%2bdisk%2bto%2bXenServer which is a valid url equivalent to /display/INFO/How+to+reattach+a+disk+to+XenServer. My problem is that the expression does not match at all, so it does not even replace a single occurrence of %25. I understand that there is a limit in the number of redirects and I should really use the [N] flag however I don't even get the first step right.

  Read the article

• Why can't my networks reach each other?

  - by HOLOGRAPHICpizza

  We have two Buffalo WZR-HP-G300NH2 routers, with the default firmware, DD-WRT v24SP2-MULTI (10/31/11) std - build 17798. Each has a separate cable internet connection with a public static IP address. They are both in the 24.123.68.0/24 space. Both of them can contact pretty much the whole internet, and they can both be accessed out on the internet with no problem, but for some reason they can't talk to each other! When I try to ping one from the other I always get "Destination Host Unreachable". There are no strange routing or firewall rules in place. And they are both set to respond to pings, I can ping them from outside. Our main IT guy is going to call our ISP on Monday, but I'm impatient, so does anyone have any ideas?

  Read the article

• Convert Google Video URL [on hold]

  - by user3716328

  When i download a video from YouTube(Google docs or Google plus) with a download manager this what i get referer: http://www.youtube.com/watch?v=71zlOWbEoe8 address: http://r4---sn-5hnezn76.googlevideo.com/videoplayback?id=o-AAyCp6dqoOj_sUwGtSwE9J27TU7-iKHf4d209xDnuCee&signature=2EB6338E125E84AAA3736DBCEF6AC35451A2104A.1C29A8A9B830CDC9E4493D93A25BA62FF3672E4A&key=cms1&ipbits=0&fexp=3300091%2C3300111%2C3300130%2C3300137%2C3300164%2C3310366%2C3310648%2C3310698%2C3312169%2C907050%2C908562%2C913434%2C923341%2C924203%2C930008%2C932617%2C935501%2C939936%2C939937&ratebypass=yes&ip=41.230.222.50&upn=DO_DxWpYrpg&expire=1402102715&sparams=expire,gcr,id,ip,ipbits,itag,ratebypass,source,upn&itag=18&source=youtube&gcr=tn&redirect_counter=1&req_id=8a4c0009cb74c822&cms_redirect=yes&ms=nxu&mt=1402081178&mv=m&mws=yes And I want to know if i have the address is there a way to get the referer I mean if i have this : http ://r4---sn-5hnezn76.googlevideo. com/videoplayback?id...... how to get http ://www.youtube.com/watch?v=......... ?

  Read the article

• NGINX returning 404 error on a valid url

  - by Harrison

  We have a site that runs PHP-FPM and NGINX. The application sends invitations to site members that are keyed with 40 character random strings (alphanumerics only -- example below). Today for the first time we ran into an issue with this approach. The following url: http://oursite.com/notices/response/approve/1960/OzH0pedV3rJhefFlMezDuoOQSomlUVdhJUliAhjS is returning a 404 error. This url format has been working for 6 months now without an issue, and other urls following this exact format continue to resolve properly. We have a very basic config with a simple redirect to a front controller, and everything else has been running fine for a while now. Also, if we change the last character from an "S" to anything other than a lower-case "s", no 404 error and the site handles the request properly, so I'm wondering if there's some security module that might see something wrong with this specific string... Not sure if that makes any sense. We are not sure where to look to find out what specifically is causing the issue, so any direction would be greatly appreciated. Thanks! Update: Adding a slash to the end of the url allowed it to be handled properly... Would still like to get to the bottom of the issue though. Solved: The problem was caused by part of my configuration... Realized I should have posted, but was headed out of town and didn't have a chance. Any url that ended in say "css" or "js" and not necessarily preceded by a dot (so, for example, http://site.com/response/somerandomestringcss ) was interpreted as a request for a file and the request was not routed through the front controller. The problem was my regex for disabling logging and setting expiration headers on jpgs, gifs, icos, etc. I replaced this: location ~* ^.+(jpg|jpeg|gif|css|png|js|ico)$ { with this: location ~* \.(jpg|jpeg|gif|css|png|js|ico)$ { And now urls ending in css, js, png, etc, are properly routed through the front controller. Hopefully that helps someone else out.

  Read the article

• mod_rewrite and SEO friendliness

  - by John Doe

  My website has an atypical structure and I'm not sure if this could create problems in the long run, specially for SEO positioning purposes. I have a unique, large PHP script, and I use the Apache module mod_rewrite in the .htaccess file to create friendly URLs, for example: RewriteRule ^$ /index.php?section=Main RewriteRule ^createArticle$ /index.php?section=Main&view=CreateArticle RewriteRule ^configuration$ /index.php?section=Configuration RewriteRule ^article/([0-9]{1,10})$ /index.php?section=Article&view=Default&id=$1 RewriteRule ^deleteArticle/([0-9]{1,10})$ /index.php?section=Article&view=Delete&id=$1 RewriteRule ^reportArticle/([0-9]{1,10})$ /index.php?section=Article&view=Report&id=$1 RewriteRule ^logIn$ /index.php?section=Authentication ... So, www.example.com/index.php?section=Article&view=Default&id=105 would become www.example.com/article/105. The only real physical file is index.php, in which the parameters of the URL queried is processed and the corresponding result is outputted. My question is, do the crawling robots (e.g. Googlebot) recognize these links? Do they index the resulting HTML outputted by index.php with the specified parameters as if it was a actual HTML file? Also, would this become a problem when creating a Sitemap?

  Read the article

• Setting up sendmail to perform mail routing

  - by Diden

  Is sendmail is able to do the following: Forward many user emails to office 365:- [email protected] -> [email protected] [email protected] -> [email protected] [email protected] -> [email protected] [email protected] -> [email protected] Forward the following to a separate server to run php scripts:- [email protected] [email protected] An autoresponder will be sent to the sender. Does anyone know of any sample configuration I could get this started on? Is there a good autoresponder for sendmail? Our emails are hosted on Office365 and it does not allow us to run scripts. Therefore I was considering this option. Is this viable? Please refer to the diagram for more information. Thank you.

  Read the article

• Htaccess 301 redirect dynamic URL

  - by Jarede

  I don't know a whole lot about .htaccess rules so forgive and help me ask the correct question. Currently I have a .htaccess rule like: RewriteRule ^surveys/(\S+)/directory/(\d+)/(\d+)/entry/(\d+)/?$ directories/index.cfm?sFuseAction=XXX.YYYY.ZZZZ&nDirectoryID=$2&nEntryID=$4&nCategoryID=$3&sDirectory=$1 [NC,L] which I want to do a 301 redirect to: RewriteRule ^(\S+)/directory/(\d+)/(\d+)/entry/(\d+)/?$ directories/index.cfm?sFuseAction=XXX.YYYY.ZZZZ&nDirectoryID=$2&nEntryID=$4&nCategoryID=$3&sDirectory=$1 [NC,L] I'm unsure of the correct syntax to go about making these redirect correctly.

  Read the article

• How to set which IP to use for a HTTP request?

  - by GetFree

  This is probably a silly question. I'm doing some http requests using wget from the command line, and I want those connections to be made through one specific IP of the 4 IPs my server has. Those http requests go to one specific range of IPs so I only want those to be routed differently. The 4 interfaces in my server are eth0, eth0:0, eth0:1, eth0:2. I tried with the following command: route add -net 192.164.10.0/24 dev eth0:0 But when I see the routing table it says: Destination Gateway Genmask Flags MSS Window irtt Iface 192.164.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 The interface is set to eth0 not eth0:0 as my command says. What am I doing wrong?

  Read the article

• private subnet nat (openvpn / racoon)

  - by Jonas Schnelli

  I have a openvpn subnet 10.8.0.0/24 running one server and one client (laptop). openvpn works fine. Browsing the web over openvpn from the laptop works also fine. Now on the server there is a private subnet with 10.7.8.128/28. The subnet is set up with racoon (IPSEC s2s vpn). The s2s vpn allows me to access the subnet 10.3.5.0/24 at the other s2s vpn end. Works all fine when I'm connected with ssh to my server. From my laptop i can ping 10.7.8.129 (the servers ipsec local ip) but i cannot reach the net 10.3.5.0/24. I tried to add a static route on my laptop 10.3.5.0/24 over gw 10.7.8.129 with no success. Any ideas how i do setup the nat / routing? Thanks

  Read the article

• how to design network for connectivity between private and corporate LANs?

  - by maruti

  there is a bunch of servers connected to shared storage in a private LAN (10.x.x.x). this privateLAN is managed by a windows server (DHCP, DNS and directory services) these hosts need to be from outside of the datacenter Eg. Remote desktop. can the NIC2 on each of the hosts be connected to the other public LAN (compromising speed or security? what are improtant considerations: additional hardware? like switches? routing&DNS software? currently available hardware : Dell Powerconnect 6224 switch .... planning this for storage network. software: windows 2003 server for DHCP, DNS, A/D ? would it be more flexible to use Linux distributions like IPCOP, Untangle etc? all that I am looking for is good isolation between private and other networks, avoid DHCP, DNS, AD clashes.

  Read the article

• htaccess url rewrite

  - by user761396

  i used to have a rewrite rule to RewriteRule ^([^/]+)\.htm$ index.php?c=$1 [NC] RewriteRule ^([^/]+)\.htm/([0-9.]+)$ index.php?c=$1&amt=$2 [NC] now, i have to change to RewriteRule ^1/([^/]+)\.htm$ index.php?c=$1 [NC] RewriteRule ^1/([^/]+)\.htm/([0-9.]+)$ index.php?c=$1&amt=$2 [NC] RewriteRule ^2/([^/]+)\.htm$ index2.php?c=$1 [NC] RewriteRule ^2/([^/]+)\.htm/([0-9.]+)$ index2.php?c=$1&amt=$2 [NC] (the difference is adding a subdirectory) my question is how to redirect my old ones to the 1/ subdirectory? thank you

  Read the article

• Separating my VPN connection from my internet access

  - by Christi

  Background: Home PC is Windows XP and using Cisco VPN client; home internet connection is fast (20MB) office VPN router is Cisco RV110W; work internet connection is slow (1.5MB) With VPN connected, my home PC internet surfing is very slow. I looked this up in Google and found talk about splitting, tunneling, routing tables, etc., but I'm not sure what/how to do it. Basically, I would like a persistent VPN connection with the office resources, and at the same time, utilize my home high speed internet connection to access the internet. Can someone help me the steps as how-to?

  Read the article

• OpenVPN + iptables / NAT routing

  - by Mikeage

  I'm trying to set up an OpenVPN VPN, which will carry some (but not all) traffic from the clients to the internet via the OpenVPN server. My OpenVPN server has a public IP on eth0, and is using tap0 to create a local network, 192.168.2.x. I have a client which connects from local IP 192.168.1.101 and gets VPN IP 192.168.2.3. On the server, I ran: iptables -A INPUT -i tap+ -j ACCEPT iptables -A FORWARD -i tap+ -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.2.0/24 -o eth0 -j MASQUERADE On the client, the default remains to route via 192.168.1.1. In order to point it to 192.168.2.1 for HTTP, I ran ip rule add fwmark 0x50 table 200 ip route add table 200 default via 192.168.2.1 iptables -t mangle -A OUTPUT -j MARK -p tcp --dport 80 --set-mark 80 Now, if I try accessing a website on the client (say, wget google.com), it just hangs there. On the server, I can see $ sudo tcpdump -n -i tap0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tap0, link-type EN10MB (Ethernet), capture size 96 bytes 05:39:07.928358 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 558838 0,nop,wscale 5> 05:39:10.751921 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 559588 0,nop,wscale 5> Where 74.125.67.100 is the IP it gets for google.com . Why isn't the MASQUERADE working? More precisely, I see that the source showing up as 192.168.1.101 -- shouldn't there be something to indicate that it came from the VPN? Edit: Some routes [from the client] $ ip route show table main 192.168.2.0/24 dev tap0 proto kernel scope link src 192.168.2.4 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.101 metric 2 169.254.0.0/16 dev wlan0 scope link metric 1000 default via 192.168.1.1 dev wlan0 proto static $ ip route show table 200 default via 192.168.2.1 dev tap0

  Read the article

• Windows 2003 - RAS service - VPN client can only connect to server, not internal network

  - by Gk

  Here is my diagram http://imageshack.us/photo/my-images/263/vpnt.png/ Server has two NIC: One connect to Internet, one connect to internal network. RAS service is configured with static IP pool on the same subnet of internal network (10.10.0.x). The problem is when a client connect to server, client can connect to server(10.10.0.10), but cannot connect to another host locate in internal network (10.10.0.11) even cannot ping to 10.10.0.50. RAS configured with IP routing enabled, client connect with options: Use default gateway on remote network. I'm messed up and can not figure out what wrong. Please help me T_T. TIA, giobuon

  Read the article

• How to create persistent static route on Mac OS X 10.6?

  - by kopobamypa

  I need to add static route on Mac OS. I found good description here Permanent Static Route Mac OS X 10.4.0 and followed the Roark Holz's (roarkh) solution. Now my problem: sometimes this solution works, sometimes does not. When it doesn't work I see these messages after boot in the Console Messages log: 06.05.10 9:34:13 com.apple.launchd[1] *** launchd[1] has started up. *** 06.05.10 9:34:46 com.apple.SystemStarter[30] Adding Static Route to 10.152 06.05.10 9:34:46 com.apple.SystemStarter[30] route: writing to routing socket: Network is unreachable 06.05.10 9:34:46 com.apple.SystemStarter[30] add net 10.152.0.0: gateway 192.168.1.234: Network is unreachable I want to know what is going on. How this kind of problem can be troubleshooted?

  Read the article

• Application request routing, images, javascript, css

  - by Cédric Boivin

  I recently install ARR with a web farm. Everyting seen to be install correctly, but my javascript, images and css don't work. The page working fine. Did i need to configure someting for image, js, css work ?

  Read the article

• Inbound connections using Internet Connection Sharing in Apple/Mac/Leopard

  - by tlianza

  I have a Mac mini which I'm using to give some other devices wireless access, by sharing it's Airport connection with the local ethernet, and that is plugged into a switch. All devices can get online no problem. (See how: http://www.macosxhints.com/article.php?story=20041112101646643 and http://www.macosxhints.com/article.php?story=20071223001432304 ) The issue is that I need to be able to connect in to these machines as well (at least, for the Slingbox to work). All the devices have 192.168.2.* addresses, and the rest of my local network is on 192.168.1.*. I tried setting a static route so that the 192.168.2.* addresses would use a gateway of 192.168.1.50 (my mac mini's address) but that didn't seem to help. Does anyone know if what I'm trying to do is possible? I admit I'm not certain what Internet Connection sharing is really doing under the hood... perhaps it just does basic nat, and doesn't do the type of routing I'm looking for. If so, anyone know if this is possible?

  Read the article

• Unable to access internet if wireless enabled

  - by balki

  The following is my route output. eth0 is my wired network and eth1 is my wireless network. Only wired one has access to internet. If I enable wireless, I am not able to access internet, it tries to access via eth1 and I get 404 page of the wireless router. Why does eth1 have higher preference though default is eth0 (link)? [balakrishnan@mylap ~]$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.26.0.1 0.0.0.0 UG 0 0 0 eth0 10.26.0.0 * 255.255.192.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 192.168.1.0 * 255.255.255.0 U 9 0 0 eth1

  Read the article

• Rails 3 + Nginx + Passenger -- Routing index

  - by Bijan

  I have no index.html file in my public folder. My rails routes file routes this, and it works fine when I run 'rails server' on my machine. I'm trying to deploy the app. I have passenger and nginx running When I run rails server on my local machine, it works fine. But it's just trying to access static file when I try to access it on the production server. Here's my nginx conf: worker_processes 1; #pid logs/nginx.pid; events { worker_connections 1024; } http { passenger_root /usr/lib/ruby/gems/1.9.1/gems/passenger-3.0.2; passenger_ruby /usr/bin/ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { listen 80; server_name mmjconsult.com; root /www/mmjs/public; access_log logs/host.access.log; passenger_enabled on; } } Thank you for any help. I really appreciate it.

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >