Search Results

Search found 21500 results on 860 pages for 'ajax request'.

Page 731/860 | < Previous Page | 727 728 729 730 731 732 733 734 735 736 737 738  | Next Page >

• How to get a new-pssession in PowerShell to talk to my ICS-connected laptop for Remoting

  - by Scott Bilas

  If I have my laptop on the LAN, then Powershell remoting works fine from my workstation to the laptop. However, the LAN is wireless, and so sometimes I will connect on a wire to my workstation. It has two ethernet ports so I have the secondary wired up to share to the laptop using Win7's Internet Connection Sharing. (Btw I know that avoiding ICS would solve the problem, but that's not an option right now.) So my question is: what magic registry bits or command line options do I need to flip to get remoting to work to my laptop through ICS? Here's what happens when I try it: new-pssession -computername 192.168.137.161 [192.168.137.161] Connecting to remote server failed with the following error message : The WinRM client cannot process the request. Default authentication may be used with an IP address under the following conditions: the transport is HTTPS or the destination is in the TrustedHosts list, and explicit credentials are provided. Use winrm.cmd to configure TrustedHosts. Note that computers in the TrustedHosts list might not be authenticated. For more information on how to set TrustedHosts run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic. + CategoryInfo : OpenError: (System.Manageme....RemoteRunspace:RemoteRunspace) [], PSRemotingTransportException + FullyQualifiedErrorId : PSSessionOpenFailed I'm having a hard time understanding the documentation for PowerShell and WinRM. I've tried messing with allowing ports in the firewall and setting TrustedHosts to * on my workstation (don't think this is a good idea on the laptop). I have no idea where to go from here, would appreciate any help.

  Read the article

• How to set up that specific domains are tunneled to another server

  - by Peter Smit

  I am working at an university as research assistant. Often I would like to connect from home to university resources over http or ssh, but they are blocked from outside access. Therefore, they have a front-end ssh server where we can ssh into and from there to other hosts. For http access they advise to set up an ssh tunnel like this ssh -L 1234:proxyserver.university.fi:8080 publicsshserver.university.fi and put the proxy settings of your browser to point to port 1234 All nice and working, but I would not like to let all my other internet traffic go over this proxy server, and everytime I want to connect to the university I have to do this steps again. What would I like: - Set up a ssh tunnel everytime I log in my computer. I have a certificate, so no passwords are needed - Have a way to redirect some wildcard-domains always through the ssh-server first. So that when I type intra.university.fi in my browser, transparently the request is going through the tunnel. Same when I want to ssh into another resource within the university Is this possible? For the http part I think I maybe should set up my own local transparent proxy to have this easily done. How about the ssh part?

  Read the article

• PHP crashing during oAuth scripts

  - by FunkyChicken

  I just installed Nginx 1.2.4 and PHP 5.4.0 (from svn) (php fpm). CentOs 5.8 64 The problem I have is that PHP crashes the moment I run any social oAuth scripts. I have tried to log into Facebook, Twitter and Google with various scripts that I know work on my other servers. When I load the scripts I get a 502 error from Nginx. And I find these errors in the log: in php-fpm log: WARNING: [pool www] child 23821 exited on signal 11 (SIGSEGV) after 1132.862984 seconds from start in nginx log: ERROR: recv() failed (104: Connection reset by peer) while reading response header from upstream From what I can see, it goes wrong when PHP tries to make a request to any of the oAuth servers. https://github.com/mahmudahsan/PHP-SDK-3.0---Graph-API-base-Facebook-Connect-Tutorial-Source for example is one of the scripts that works perfectly on my other machines, but causes PHP to crash. I found: http://stackoverflow.com/questions/3616191/nginx-php-fpm-502-bad-gateway which seems to be a similar problem, but I cannot find a way to solve it. +++ UPDATE +++ Now I have been doing some debugging in 1 of the scripts that is playing up. If you go to line 808 http://pastebin.com/gSnzRtXb it runs the curl_exec() command. When that is ran, it crashes. If i echo'test';exit; just above that line, it echo's correctly, if i do it below that line, php crashes. Which means it's that line 808 which causes the crash. So I made a very simple script to do some testing: http://pastebin.com/Rshnyhcm which also uses curl_exec, but that runs just fine. So I started to dig deeper into that query from the facebook script to see what values the $opts array contains from line 806. Output of that array is: http://pastebin.com/Cq9ffd3R What the problem is, I still have no clue :(

  Read the article

• SQL Server 2008 second instance times out when logging in -- but only the first time?

  - by Kromey

  This is a strange one that has plagued me for a while now. When logging in to the second instance of SQL Server 2008 on one of our database servers, we get a timeout error: Cannot connect to servername\mssqlserver2. Additional information: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. (Microsoft SQL Server)") (This is the error message when trying to connect with Microsoft SQL Server Management Studio; other tools experience the same error, but of course say it in different ways.) Immediately re-attempting to log in works just fine, so whatever the cause it's ephemeral! This happens regardless of user or authentication type (both Windows and SQL Server authentication methods are supported on this instance). What's even weirder, though, is that the first instance on this server has never once demonstrated this problem. Server is a Windows Server 2008 R2 virtual server, hosted in Microsoft Hyper-V (host is likewise Server 2008 R2). The server has 2GB of RAM, and seems to regularly be using 90% of that -- could low memory be the cause of this issue? I could see this second instance -- which is not used very often yet -- being swapped out to disk, and then taking too long to load back into memory to respond in time to the connection request, but I'd rather have more than just my own hunch before I go scheduling a downtime for this server (the first instance is used regularly) and then just throwing extra resources at it in the blind hope that the problem goes away.

  Read the article

• Using %v in Apache LogFormat definition matches ServerName instead of specific vhost requested

  - by Graeme Donaldson

  We have an application which uses a DNS wildcard, i.e. *.app.example.com. We're using Apache 2.2 on Ubuntu Hardy. The relevant parts of the Apache config are as follows. In /etc/apache2/httpd.conf: LogFormat "%v %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vlog In /etc/apache2/sites-enabled/app.example.com: ServerName app.example.com ServerAlias *.app.example.com ... CustomLog "|/usr/sbin/vlogger -s access.log /var/log/apache2/vlogger" vlog Clients access this application using their own URL, e.g. company1.app.example.com, company2.app.example.com, etc. Previously, the %v in the LogFormat directive would match the hostname of the client request, and we'd get several subdirectories under /var/log/apache2/vlogger corresponding to the various client URLs in use. Now, %v appears to be matching the ServerName value, so we only get one log under /var/log/apache2/vlogger/app.example.com. This breaks our logfile analysis because the log file has no indication of which client the log relates to. I can fix this easily by changing the LogFormat to this: LogFormat "%{Host}i %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vlog This will use the HTTP Host: header to tell vlogger which subdirectory to create the logs in and everything will be fine. The only concern I have is that this has worked in the past and I can't find any indication that this has changed recently. Is anyone else using a similar config, i.e. wildcard + vlogger and using %v? Is it working fine?

  Read the article

• Using IIS7 as a reverse proxy

  - by Eric Petroelje

  I'm setting up a server at home to host a few small websites. One of them is .NET based and needs IIS, the others are PHP based and need Apache. So, I have both IIS 7 and Apache 2.2.x installed on my server with IIS on port 80 and Apache running on port 8080. I would like to set up IIS to work as a reverse proxy, forwarding the requests for the Apache sites to port 8080 and serving the requests for the .NET site itself based on the host headers. Like this: www.mydotnetsite.com/* -> IIS -> serve from IIS www.myapachesite.com/* -> IIS -> forward to apache on port 8080 www.myothersite.com/* -> IIS -> forward to apache on port 8080 I did a bit of googling and it seemed like the Application Request Routing feature would do what I needed, but I can't seem to get it to work the way I want it to. I can get it to forward ALL traffic to the Apache server and I can get it to forward traffic with a specific URL pattern to the Apache server, but I can't seem to get it to forward based on the host headers (e.g. "forward all requests for www.apachesite.com - localhost:8080") So the question is, how would I go about configuring ARR to do this? Or do I need a different tool? I'm also open to using Apache as the reverse proxy and forwarding the .NET site requests to IIS instead if that's easier (running Apache on port 80 and IIS on 8080).

  Read the article

• Inconsistent DHCP replies with Windows 2008R2 DHCP server

  - by verbalicious

  I've got a Windows 2008R2 standard server running DHCP services. We've noticed that certain clients are receiving inconsistent DHCP replies. We have over 175 Windows workstations in this VLAN that don't seem to have trouble getting DHCP leases. However, PXE-booting clients trying to reach our DHCP server are able to get a lease inconsistently. Additionally, we tried using the "dhcping" tool against our DHCP server and found that roughly two of every three requests time out with "no answer" -- and this holds true when we set the timeout value on dhcping to 20seconds. After a failed attempt, however, we may get a dhcp lease reply immediately with dhcping. This leads me to believe that this issue isn't confined to PXE booting clients, but something more systemic with my LAN layer2 or DHCP. And that possibly my 175 windows clients are experiencing this in some form without my knowledge. We have over 30% of our scope available so the addresses are there. I was unable to find anything in the Windows server "DHCP-Server" log. Of course, my goal is to have my DHCP server reply to every request that it receives on the LAN!

  Read the article

• Debian, Apache2, CGI: paths issue

  - by Bubnoff

  I have a perl form email script on the servers cgi-bin directory ( /usr/lib/cgi-bin ). /etc/apache2/sites-enabled/000-default ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch AddHandler cgi-script cgi pl Order allow,deny Allow from all </Directory> The issue is with paths. html calls script here: <form name="Request" method="post" action="http://server-test.local/cgi-bin/formprocessorpro.pl" onsubmit="return checkWholeForm49874(this)"> The directory with the templates and configs is passed here: <input type="hidden" name="base_path" value="../contact" /> The path to this form is: http://server-test.local/formstest/contact.htm No matter what variation I try for the base_path I get an error from the formprocessor script that it can't find the directory: An error occurred when opening the Form Configuration File (../contact/form.cfg): No such file or directory. I need to move this script from an old server, configured by a previous sysadmin, to a new server. Since cgi-bin is automatically linked to /usr/lib/cgi-bin and linked such that the script resides: http://server-test.local/cgi-bin/formprocessorpro.pl I would imagine that, given that the templates are in the webroot in a directory called contact, the correct path would be: ../contact Any ideas? It's been awhile since I've messed with CGI. Bubnoff

  Read the article

• Azure's Ubuntu 12.0.4 fails to install PHP5

  - by Alex Kennberg

  Similar to this article from Azure themselves: http://www.windowsazure.com/en-us/manage/linux/common-tasks/install-lamp-stack/ I am trying to install PHP5 on Ubuntu 12.0.4 virtual machine. However, it fails installing the ssl-cert. $ sudo apt-get install php5 Reading package lists... Done Building dependency tree Reading state information... Done php5 is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 49 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up ssl-cert (1.0.28) ... Could not create certificate. Openssl output was: Generating a 2048 bit RSA private key ............................+++ ...................................................................................................................+++ writing new private key to '/etc/ssl/private/ssl-cert-snakeoil.key' ----- problems making Certificate Request 140320238503584:error:0D07A097:asn1 encoding routines:ASN1_mbstring_ncopy:string too long:a_mbstr.c:154:maxsize=64 dpkg: error processing ssl-cert (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: ssl-cert E: Sub-process /usr/bin/dpkg returned an error code (1) Any tips appreciated.

  Read the article

• Cyrus: In practical terms, how do end users administer their shared mailboxes?

  - by Nick

  Let's say we have four customer service reps: Billy, Bob, Joe, and Tom. Tom is the department manager. There's a shared Customer Service mailbox on the Cyrus server that they all have access to. Tom, as the manager also has administrative privileges for the shared mailbox. They decide they want to create sub-folders a certain way, and Tom creates them. They're all running Thunderbird, so Tom right-clicks the main folder and chooses "New Subfolder". Now Tom has the Subfolders he needs and the other sales reps have... nothing! Because Cyrus created the Subfolders giving Tom "Full Access" permissions, and everyone else gets no access. So how does Tom give the other reps in his department access to the new folders? As far as Cyrus is concerned, Tom has permission to grant others access to his new mailboxes- But as far as I can tell, there's no option in Thunderbird for granting mailbox permissions. An IT staff member should not have to receive a support request every time someone wants to add a Subfolder to a shared mailbox. That's why we make certain users into mailbox admins in the first place! But asking (non-technical) users to SSH into an IMAP server to run cyradm seems like a bad idea too. Certainly someone has found a solution for this dilemma. Perhaps a Thunderbird extension for setting Cyrus permissions? Or something like umask that forces subfolders to have identical permissions to their parents on creation? And related, what about Sieve configuration? Is there anyway that can be done from the client machine too? Thanks, Nick

  Read the article

• Cannot establish XMPP server-to-server connection to gmail

  - by v_2e

  My jabber-server fails to connect to gmail.com giving the error: outgoing s2s stream myserver.com.ua-bot.talk.google.com closed: undefined-condition (myserver.com.ua is a Google Apps Domain with Talk service enabled.) I am using the Prosody XMPP server. It works just fine with other jabber-servers I tested so far (e.g. jabber.ru). However, when some of my clients tries to add a gmail contact to his contact-list, the subscription request lasts forever, and the Prosody gives the following sequence of messages in its log: Oct 21 22:57:16 s2sout95897f8 info Beginning new connection attempt to gmail.com ([173.194.70.125]:5269) Oct 21 22:57:16 s2sout95897f8 info sent dialback key on outgoing s2s stream Oct 21 22:57:16 s2sout95897f8 info Session closed by remote with error: undefined-condition (myserver.com.ua is a Google Apps Domain with Talk service enabled.) Oct 21 22:57:16 s2sout95897f8 info outgoing s2s stream myserver.com.ua->gmail.com closed: undefined-condition (myserver.com.ua is a Google Apps Domain with Talk service enabled.) Oct 21 22:57:16 s2sout95897f8 info sending error replies for 2 queued stanzas because of failed outgoing connection to gmail.com Here for the domain name of my server I use myserver.com.ua I found a similar problem described in this thread, but there is no detailed description of the solution there. As for the Google services, I did have a google account where I added the domain name under question to the Webmasters tools page. However, I deleted my account long ago, so now it is unclear, how any of the Google services can relate to my domain name. So my question is: What is the real cause of this problem (my jabber-server configuration or imaginary Google account or something else) and how can I make my Prosody server connect to gmail.com jabber service?

  Read the article

• How do I make Nginx redirect all requests for files which do not exist to a single php file?

  - by Richard

  I have the following nginx vhost config: server { listen 80 default_server; access_log /path/to/site/dir/logs/access.log; error_log /path/to/site/dir/logs/error.log; root /path/to/site/dir/webroot; index index.php index.html; try_files $uri /index.php; location ~ \.php$ { if (!-f $request_filename) { return 404; } fastcgi_pass localhost:9000; fastcgi_param SCRIPT_FILENAME /path/to/site/dir/webroot$fastcgi_script_name; include /path/to/nginx/conf/fastcgi_params; } } I want to redirect all requests that don't match files which exist to index.php. This works fine for most URIs at the moment, for example: example.com/asd example.com/asd/123/1.txt Neither of asd or asd/123/1.txt exist so they get redirected to index.php and that works fine. However, if I put in the url example.com/asd.php, it tries to look for asd.php and when it can't find it, it returns 404 instead of sending the request to index.php. Is there a way to get asd.php to be also sent to index.php if asd.php doesn't exist?

  Read the article

• InstantSSL's certificate no different than a self signed certificate under Nginx with an IP accessed address

  - by Absolute0

  I ordered an ssl certificate from InstantSSL and got the following pair of files: my_ip.ca-bundle, my_ip.crt I also previously generated my own key and crt files using openssl. I concatenated all the crt files: cat my_previously_generted.crt my_ip.ca_bundle my_ip.crt chained.crt And configured nginx as follows: server { ... listen 443; ssl on; ssl_certificate /home/dmsf/csr/chained.crt; ssl_certificate_key /home/dmsf/csr/csr.nopass.key; ... } I don't have a domain name as per the clients request. When I open the browser with https://my_ip chrome gives me this error: The site's security certificate is not trusted! You attempted to reach my_ip, but the server presented a certificate issued by an entity that is not trusted by your computer's operating system. This may mean that the server has generated its own security credentials, which Google Chrome cannot rely on for identity information, or an attacker may be trying to intercept your communications. You should not proceed, especially if you have never seen this warning before for this site.

  Read the article

• Finding ALL currently used IP addresses of Website

  - by Patrick R

  What steps would you take to discover all (or close to all) IP addresses that are currently used by a website? How would you be as exhaustive as possible without calling a website admin and asking for the list of IP addresses? ;) nslookup works but will vary based on dns server queried. whois is another good tool. Dig, not bad. Let's use Facebook for example. I'm blocking that site for the majority our our company's users, but some are approved for "research". I can not easily use OpenDNS because we all appear to come from the same request IP address. I could change that but don't want to add more vlans than I already have. I also could use block something like regex facebook1 "facebook\.com" (I'm running a cisco firewall) but that's pretty easy to sidestep. All that being said, I'm asking about specifically about finding ip addresses for a domain and not for other methods that I can block a domain name.

  Read the article

• Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues...

  - by upkels

  I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

  Read the article

• Some HTTPS connections via NAT fail, but work on firewall itself.

  - by hnxn

  Hi, I am having trouble establishing some HTTPS connections from internal machines, even though these same connections work if initiated on the firewall itself. The firewall machine is running Ubuntu 10.04.1 and shorewall 4.4.6. The internet connection is Bell PPPoE DSL (in Canada). I have tried various MTU settings, it doesn't seem to make any difference. Other protocols (HTTP, FTP, etc) generally work. The problem seems to be limited to certain sites; this one never works from an internal machine, but always works from the firewall itself: From internal machine: $ wget https://images.fedex.com/images/ascend/shared/headers/nxgen/corp_logo.gif --2011-01-13 20:51:31-- https://images.fedex.com/images/ascend/shared/headers/nxgen/corp_logo.gif Resolving images.fedex.com... 184.24.96.69 Connecting to images.fedex.com|184.24.96.69|:443... connected. ^C From firewall: $ wget https://images.fedex.com/images/ascend/shared/headers/nxgen/corp_logo.gif --2011-01-13 20:58:28-- https://images.fedex.com/images/ascend/shared/headers/nxgen/corp_logo.gif Resolving images.fedex.com... 184.24.96.69 Connecting to images.fedex.com|184.24.96.69|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 840 [image/gif] Saving to: `corp_logo.gif' 2011-01-13 20:58:28 (149 MB/s) - `corp_logo.gif' saved [840/840] This URL always works from both internal and firewall: https://encrypted.google.com/images/logos/ssl_logo_lg.gif Any troubleshooting tips would be greatly appreciated!

  Read the article

• Setting up PerformancePoint Services on Sharepoint 2010: connection errors

  - by Rik

  I have tried to setup PerformancePoint Services on SharePoint 2010, but every time I try to use the dashboard designer, I get this error: “An error has occurred attempting to contact the specified SharePoint site” I have tried these steps but it hasn't helped. Any ideas? The event log gives the following information: WebHost failed to process a request. Sender Information: System.ServiceModel.ServiceHostingEnvironment+HostingManager/24724999 Exception: System.ServiceModel.ServiceActivationException: The service '/_vti_bin/client.svc' cannot be activated due to an exception during compilation. The exception message is: This collection already contains an address with scheme http. There can be at most one address per scheme in this collection. Parameter name: item. --- System.ArgumentException: This collection already contains an address with scheme http. There can be at most one address per scheme in this collection. Parameter name: item at System.ServiceModel.UriSchemeKeyedCollection.InsertItem(Int32 index, Uri item) at System.Collections.Generic.SynchronizedCollection`1.Add(T item) at System.ServiceModel.UriSchemeKeyedCollection..ctor(Uri[] addresses) at System.ServiceModel.ServiceHost..ctor(Type serviceType, Uri[] baseAddresses) at System.ServiceModel.Activation.ServiceHostFactory.CreateServiceHost(Type serviceType, Uri[] baseAddresses) at System.ServiceModel.Activation.ServiceHostFactory.CreateServiceHost(String constructorString, Uri[] baseAddresses) at System.ServiceModel.ServiceHostingEnvironment.HostingManager.CreateService(String normalizedVirtualPath) at System.ServiceModel.ServiceHostingEnvironment.HostingManager.ActivateService(String normalizedVirtualPath) at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath) --- End of inner exception stack trace --- at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath) at System.ServiceModel.ServiceHostingEnvironment.EnsureServiceAvailableFast(String relativeVirtualPath) Process Name: w3wp Process ID: 2576

  Read the article

• Ubuntu Pound Reverse Proxy Load Balancing Based off active server load?

  - by Andrew

  I have Pound installed on a loadbalancer. It seems to work okay, except that it randomly assigns the backend server to forward the request to. I've put 1 backend machine under so much load that it went into using swap, and I can't even ssh into it to test this scenareo. I would like the loadbalancer to realize that the machine is overloaded, and send it to a different backend machine. However it doesn't. I've read the man page and it seems like the directive "DynScale 1" is what would monitor this, but it still redirects to the overloaded server. I've also put in "HAport 22" to the backend figuring since I can't ssh in, neither could the loadbalancer and it would consider the backend server dead until it gets rid of the load and responds, but that didn't help either. If anyone could help with this, I'd appreciate it. My current config is below. ###################################################################### ## global options: User "www-data" Group "www-data" #RootJail "/chroot/pound" ## Logging: (goes to syslog by default) ## 0 no logging ## 1 normal ## 2 extended ## 3 Apache-style (common log format) LogLevel 3 ## check backend every X secs: Alive 5 DynScale 1 Client 1200 TimeOut 1500 # poundctl control socket Control "/var/run/pound/poundctl.socket" ###################################################################### ## listen, redirect and ... to: ## redirect all requests on port 80 to SSL ListenHTTP Address 192.168.1.XX Port 80 Service Redirect "https://xxx.com/" End End ListenHTTPS Address 192.168.1.XX Port 443 Cert "/files/www.xxx.com.pem" Service BackEnd Address 192.168.1.1 Port 80 HAport 22 End BackEnd Address 192.168.1.2 Port 80 HAport 22 End End End

  Read the article

• Is StoreJet Transcend (0x2329) an Advanced Format drive?

  - by Graham Perrin

  I use a 640 GB StoreJet Transcend (0x2329) with ZEVO Community Edition 1.1.1 on OS X 10.8.2. Question Is this drive Advanced Format? Background I submitted a request for technical support to Transcend but the first response was gibberish so I don't expect a reasonable follow-up. Models at http://www.transcend-info.com/Products/CatList.asp?LangNo=0&ModNo=293 are similar but different sizes (not 640 GB). Mine is probably 25M2 (TS640GSJ25M2): Unless I'm missing something, nothing currently in the Transcend support area tells me whether the drive is Advanced Format. From System Information in OS X 10.8.2: StoreJet Transcend: Capacity: 640.14 GB (640,135,028,736 bytes) Removable Media: Yes Detachable Drive: Yes BSD Name: disk3 Product ID: 0x2329 Vendor ID: 0x152d (JMicron Technology Corp.) Version: 0.00 Serial Number: 322549FBA004 Speed: Up to 480 Mb/sec Manufacturer: JMicron History for the ZFS pool shows creation in March 2012 –  macbookpro08-centrim:~ gjp22$ zpool history zhandy | grep create 2012-03-14.17:29:37 zpool create -f -O compression=off -O copies=1 -O casesensitivity=insensitive -O snapdir=visible zhandy /dev/dsk/GPTE_1928482A-7FE4-482D-B692-3EC6B03159BA 2012-06-22.15:51:16 zfs create zhandy/Pocket Time Machine At that time I almost certainly used ZEVO Setup Assistant to create the pool. macbookpro08-centrim:~ gjp22$ zpool get ashift zhandy NAME PROPERTY VALUE SOURCE zhandy ashift 0 default If I discover that the drive is Advanced Format, a different ashift value will be appropriate.

  Read the article

• Using public interfaces on a server connected through a GRE tunnel

  - by Evan

  I'm pretty new to networking so please forgive any terminology mistakes. I have 2 servers connected with a GRE tunnel. Server1 (10.0.0.1) ---- Server2 (10.0.0.2) I want to be able to bind to the public IPs on Server2 using Server1. To do this, I setup virtual interfaces with Server2's public IPs on Server1 and then used routing rules on Server1 to route the packets through the GRE tunnel. On Server1: ip rule add from [Server2's first public IP] table gre ip rule add from [Server2's second public IP] table gre ip route add default via 10.0.0.2 dev gre1 table gre This works great and I can see the packets arriving via GRE on Server2. I can see the packet exiting the tunnel on Server2's gre1 device as shown: From Server1: ping -I [Server2's public ip] google.com tcpdump from Server2's GRE tunnel device: 12:07:17.029160 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) [Server2's public ip] > 74.125.225.38: ICMP echo request, id 6378, seq 50, length 64 This is exactly the packet I want. However, I'm not seeing it go out at all on eth0:0 (where Server2's public IP is bound to). I've tried to use routing rules to get packets coming from Server2's public IP (which would be coming out of dev gre1) to go through dev eth0 on the public default gateway and that doesn't work either. I'm at a loss, thank you to anyone who can help.

  Read the article

• 403 Forbidden error on Mac OSX - Apache and nginx

  - by tlianza

  Hi All, There are a million questions like this on Google, but I haven't found a solution to my problem. The default Apache install on my Mac is giving 403 Forbidden errors for everything (default directory, user home directory, virtual server, etc). After sifting through the config files, I figured I'd give nginx a try. Nginx serves files fine from it's home directory, but it won't serve files from a subfolder of my user directory. I've configured a simple virtual host, and requesting index.html returns a 403-forbidden. The error message in nginx's log file is pretty clear - it can't read the file: 2011/01/04 16:13:54 [error] 96440#0: *11 open() "/Users/me/Documents/workspace/mobile/index.html" failed (13: Permission denied), client: 127.0.0.1, server: local.test.com, request: "GET /index.html HTTP/1.1", host: "local.test.com" I've opened up this directory to everyone: drwxrwxrwx 6 me admin 204B Dec 31 20:49 mobile And all the files in it: $ ls -lah mobile/ total 24 drwxrwxrwx 6 me admin 204B Dec 31 20:49 . drwxr-xr-x 71 me me 2.4K Dec 31 20:41 .. -rw-r--r--@ 1 me me 6.0K Jan 2 18:58 .DS_Store -rwxrwxrwx 1 me admin 2.1K Jan 4 14:22 index.html drwxrwxrwx 5 me admin 170B Dec 31 20:45 nbproject drwxrwxrwx 5 me admin 170B Jan 2 18:58 script And yet, I cannot figure out why the nginx process cannot read index.html. It's running as the "nobody" user, but the permissions are set such that anyone can read them.

  Read the article

• How do I Install Intermediate Certificates (in AWS)?

  - by getmizanur

  I have installed private key (pem encoded) and public key certificate (pem encoded) on Amazon Load Balancer. However, when I check the SSL with site test tool, I get the following error: Error while checking the SSL Certificate!! Unable to get the local issuer of the certificate. The issuer of a locally looked up certificate could not be found. Normally this indicates that not all intermediate certificates are installed on the server. I converted crt file to pem using these commands from this tutorial: openssl x509 -in input.crt -out input.der -outform DER openssl x509 -in input.der -inform DER -out output.pem -outform PEM During setup of Amazon Load Balancer, the only option I left out was certificate chain. (pem encoded) However, this was optional. Could this be cause of my issue? And if so; How do I create certificate chain? UPDATE If you make request to VeriSign they will give you a certificate chain. This chain includes public crt, intermediate crt and root crt. Make sure to remove the public crt from your certificate chain (which is the top most certificate) before adding it to your certification chain box of your Amazon Load Balancer. If you are making HTTPS requests from an Android app, then above instruction may not work for older Android OS such as 2.1 and 2.2. To make it work on older Android OS: go here click on "retail ssl" tab and then click on "secure site" "CA Bundle for Apache Server" copy and past these intermediate certs into certificate chain box. just incase if you have not found it here is the direct link. If you are using geo trust certificates then the solution is much the same for Android devices, however, you need to copy and paste their intermediate certs for Android.

  Read the article

• Why apache throws 403 on index file after install?

  - by den-javamaniac

  Hi. I've just installed apache and php from sources using next commands: ./configure --prefix="/mnt/workspace/servers/web/apache-2.2.17" \ --enable-info --enable-rewrite --enable-usertrack --enable-mime-magic for apache and ./configure --with-apxs2=/mnt/workspace/servers/web/apache-2.2.17/bin/apxs \ --prefix=/mnt/workspace/servers/web/apache-2.2.17/php \ --with-config-file-path=/mnt/workspace/servers/web/apache-2.2.17/php \ --with-mysql=mysqlnd for php. After adjusting configuration (httpd.conf) and starting apache it gives a 403 response on http://localhost:8060/index.html (presuming that 8060 is used) request. There are next directory settings in httpd.conf: <Directory "/mnt/workspace/servers/web/apache-2.2.17/htdocs"> ... Order allow,deny Allow from all ... </Directory> <IfModule dir_module> DirectoryIndex index.html index.php </IfModule> It should be noted that I've got apache on a mounted (default auto mount configured while installing ubuntu) partition. Log Files Access log: ::1 - - [12/Feb/2011:17:48:30 +0200] "GET / HTTP/1.1" 403 202 ::1 - - [12/Feb/2011:17:48:31 +0200] "GET /favicon.ico HTTP/1.1" 403 213 ::1 - - [12/Feb/2011:17:48:48 +0200] "GET /index.html HTTP/1.1" 403 212 ::1 - - [12/Feb/2011:17:48:48 +0200] "GET /favicon.ico HTTP/1.1" 403 213 ::1 - - [12/Feb/2011:17:49:03 +0200] "GET /index.html HTTP/1.1" 403 212 ::1 - - [12/Feb/2011:17:49:03 +0200] "GET /favicon.ico HTTP/1.1" 403 213 Error log: [Sat Feb 12 18:59:13 2011] [notice] Apache/2.2.17 (Unix) PHP/5.3.5 configured -- resuming normal operations [Sat Feb 12 18:59:22 2011] [error] [client ::1] (13)Permission denied: access to / denied [Sat Feb 12 18:59:22 2011] [error] [client ::1] (13)Permission denied: access to /favicon.ico denied [Sat Feb 12 18:59:36 2011] [error] [client ::1] (13)Permission denied: access to /index.html denied

  Read the article

• All websites migrated from server running IIS6 to IIS7

  - by Leah

  Hi, I hope someone will be able to help me with this. We have recently migrated all of our clients' sites to a new server running IIS7 - all the sites were originally running on a server running IIS6. Ever since the migration, lots of our clients are reporting error messages. There seems to be quite a number of issues related to sending emails and also, we have had the following error message reported by several different clients: Server Error in '/' Application. -------------------------------------------------------------------------------- Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that <machineKey> configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Web.HttpException: Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that <machineKey> configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. I have read elsewhere that this error can appear if a button is clicked before the whole page has finished loading. But as this error has now appeared on multiple sites and only since the server migration, it seems to me that it must be something else. I was wondering if someone could tell me if there is something specific which needs to be changed for .NET sites when sites are moved from a server running IIS6 to a server running IIS7? I don't deal with the actual servers very much so I'm afraid this is very much a grey area for me. Any help would be very much appreciated.

  Read the article

• How can Django/WSGI and PHP share / on Apache?

  - by Mark Snidovich

  I have a server running an established PHP site, as well as some Django apps. Currently, a VirtualHost set up for PHP listens on port 80, and requests to certain directories are proxied to a VirtualHost set up for Django with WSGI. I'd like to change it so Django handles anything not existing as a PHP script or static file. For example, / -parsed by PHP as index.php /page.php -parsed as PHP normally /images/border.jpg -served as a static file /johnfreep -handled by Django (interpreted by urls.py) /pages/john -handled by Django /(anything else) - handled by Django I have a few ideas. It seems the options are 'php first' or 'wsgi first'. set up Django on port 80, and set Apache to skip all the known PHP, CSS or image files. Maybe using SetHandler? Anything else goes to Django to be parsed by urls.py. Set up a script referring everything to Django as a 404 handler on PHP. So, if a file is not found for a name, it sends the request path to a VirtualHost running Django to be parsed.

  Read the article

< Previous Page | 727 728 729 730 731 732 733 734 735 736 737 738  | Next Page >