Search Results

Search found 34556 results on 1383 pages for 'setting as default'.

Page 733/1383 | < Previous Page | 729 730 731 732 733 734 735 736 737 738 739 740 | Next Page >

Error starting Hyper-V VM

- by Peter Bernier

I'm trying to start a VM on a new Hyper-V installation and I'm receiving the following error: The virtual machine could not be started because the hypervisor is not running. The following actions may help you resolve the problem: 1) Verify that the processor of the physical computer has a supported version of hardware-assisted virtualization. 2) Verify that hardware-assisted virtualization and hardware-assisted data execution protection are enabled in the BIOS of the physical computer. (If you edit the BIOS to enable either setting, you must turn off the power to the physical computer and then turn it back on. Resetting the physical computer is not sufficient.) 3) If you have made changes to the Boot Configuration Data store, review these changes to ensure that the hypervisor is configured to launch automatically. My machine supports virtualization at the hardware level and it is enabled in BIOS. Why am I receiving this error?

Read the article
How can I start using MS-SQL Server ( express )

- by Oscar Reyes

Hello. I have just installed Microsoft SQL Express from here: http://www.microsoft.com/Sqlserver/2005/en/us/express-down.aspx I need it because an example of some code I have uses it. My question is: How do I start using it? Which port it opens by default. All I have after installing it is this: I'm not asking for a full tutorial on how to admin MSSql, just a hint on what to do next. I have downloaded and tested in the past Oracle XE and test it with SQuirreL SQL client with out problems.

Read the article
problems with WindowsImageBackup and write protected drives

- by Ralph Shillington

On Windows 7 I created a System image of my computer (C: and reserved partition) onto a USB drive. No problem. I then formatted the C: and installed the OS -- no problem Now I would like use the System Image and get back some of my documents etc. But I can't get access wo the WindowsImageBackup folder on the USB drive 1) Somehow the drive is write protected --- how did that happen? How do I unprotect that drive. 2) I can't access the WindowsImageBackup folder because I suspect the ACL is out of wack with my new SID. I would add my new SID to the ACL but I can't because the drive is write protected At the moment I'm completely disconnected from my files, which I thought (and still hope) are backed up. Understandably, panic is now setting in.

Read the article
xargs -I replace-str option difference

- by foresightyj

From my understanding, the following should mean exactly the same: ls -1 | xargs file {} ls -1 | xargs -I{} file {} if -I option is not specified, it is default to -I{}. I want to list all files in the current directory and run file command on each of them. Some have spaces in their names. However, I noticed the difference. See below: $ ls -1 Hello World $ ls -1 | xargs file {} {}: ERROR: cannot open `{}' (No such file or directory) Hello: ERROR: cannot open `Hello' (No such file or directory) World: ERROR: cannot open `World' (No such file or directory) $ ls -1 | xargs -I{} file {} Hello World: directory With -I{} explicitly specified, blanks in file names are treated as expected.

Read the article
Hyper-V 2012 and P2000 SAS SAN

- by user155950

Hi I am having major problems setting up a Hyper-V 2012 cluster on a P2000 SAS SAN. Running System Center VMM 2012 SP1 I am unable to see any storage to create my cluster. Has anyone had experienced anything similar? Under fabric and storage I can't add the P2000, all I can do is use storage spaces in server manager to create a storage pool and virtual disk. This allows me to create a file share which I can add to VMM but I still can't see any disk to create a cluster. I am just about at the point where I want to tear my hair out wipe the servers and stick VMware on them because I know it works as I have set several systems up like this in the past. The Hyper-V servers can see the storage and in server manager on my management machine it seems to know both servers can see the same disk. VMM is running on the same machine and it can't see any disk. Help..... Thanks Mike

Read the article
ThinkPad TrackPoint Buttons Not Working Well

- by Oscar Godson

The TrackPoint itself works fine. But the three buttons below the spacebar don't. For example if I were to copy these lines, 1-10, using trackpoint buttons it'd start highlighting at 7. If I use the main TrackPad (the part every laptop) and it's buttons it works normal, 1-10: 1 2 3 4 5 6 7 8 9 10 It's like the button doesn't register right away. I use the TrackPoint ALL the time. I love it and I don't think I can go back to the normal TrackPad, so is there anyway to fix this? An app or setting? Also, the middle button to scroll isn't working at all I tried: Middle Button on ThinkPad Not Working with 10.10 update And put it in /usr/share/... and /usr/lib... neither seem to work. They USED to work. I used to be able to use that method of fixing it, but it seems in 11.04 this doesnt work? I dont wanna give up on Ubuntu yet...

Read the article
salted passwords confusion

- by Vasiliy Stavenko

I'm setting up email server for the first time and confused with strange thing. I have several user accounts which stored in previous server. Passwords for this accounts are in plain text. But I want to create crypts for them. Mysql (where my users will be stored) have function encrypt(passwd, salt). If no salt given used random value. I discovered that courier uses one certain salt and crypted all passwords with it. So the task done. But I'd like to know if there's a way to define my own salt for my pop3 server?

Read the article
ASP.NET Website not responding

- by brinthhillerup

Hello everybody I am setting with my server tech, trying to figure out what is going on here. When I try to access my site through a browser, my site hangs indefinately. It does not respond with anything, not even after 15 minutes! The application pool has been restarted, the website has been restarted. Doesn't helpt at all. It happened during an upload. A backup has been loaded and the problem is still the same It is a very urgent matter, I hope someone can help me! I think we are on a IIS 6 on a Windows 2003 Server. (Remote hosted, with a tech, who has no idea what the issue is as well, so I am trying to find the solution alogn with him). Any suggestions are VERY appriciated.

Read the article
Ubuntu 12.04 suddenly will not boot after compiz crash on lockscreen

- by schonjones

Yesterday i went to work and closed my laptop. When i got home I couldn't get the lock screen to come back up. ctrl+alt+f2 to get to a terminal and Tried to kill compiz, compiz was not running so I tried to restart it got an error opening the display so i tried to restart lightdm again couldn't open display. so I restarted and now I am stuck on the loading screen. I tried booting in recovery mode and all options hang except root, but i'm stuck with read only. booting from a live cd I can mount the drive but again stuck with read only. I'm completely stuck here. checking my default-display-manager returns "/usr/sbin/elsa" as the only line and can't edit it. I've got an 11.10 live cd and my /home is encrypted so i can't try to back anything up at the moment either. How can i resolve this or at the least back up some of my data? Please help!

Read the article
How do I install a Wimax usb driver?

- by kakaz

I am using wimax usb modem in Ubuntu 9.04 properly. I am familiar with Ubuntu 10.04 and try to install the same deb file to use my wimax USB modem, but it could not install and give me the following error message: $ sudo dpkg -i green-packet-wimax-usb_i386.iso.deb (Reading database ... 206628 files and directories currently installed.) Preparing to replace green-packet-wimax-usb 1.12 (using green-packet-wimax- usb_i386.iso.deb) ... /var/lib/dpkg/info/green-packet-wimax-usb.prerm: 45: /etc/init.d/wimaxd: not found Removing any system startup links for /etc/init.d/wimaxd ... FATAL: Module mt7118_usb_os not found. Unpacking replacement green-packet-wimax-usb ... Setting up green-packet-wimax-usb (1.12) ... FATAL: Error inserting mt7118_usb_glue (/lib/modules/2.6.32-28-generic/kernel/drivers/net/mt7118_usb_glue.ko): Invalid module format dpkg: error processing green-packet-wimax-usb (--install): subprocess installed post-installation script returned error exit status 1 Processing triggers for ureadahead ... Processing triggers for desktop-file-utils ... Processing triggers for python-gmenu ... Rebuilding /usr/share/applications/desktop.en_US.utf8.cache... Processing triggers for libc-bin ... ldconfig deferred processing now taking place Processing triggers for python-support ... Errors were encountered while processing: The error (Line 9) give me some clue that the mt7118_usb_glue.ko kernel object can't insert it. So, I think this may be due to it's kernel dependencies. Can anybody tell me how I can install this kernel object to my new Ubuntu 10.04 kernel?

Read the article
Connect laptop to mobile wifi

- by Arnab Sen Gupta

I have a nokia N97. In my apartment there's a wifi network that we all use to connect to the internet. But for the past few days my laptop is not able to find the network..Initially I thought it was a problem of the network,but hen I found out that others were able to use it..My vista os laptop is able to detect other available networks but not the required one..Then i tried to connect my cell phone to the network and it did easily!! I tried restoring the network settings to default but it showed the network for just 2 mins and it ws back to square one.. I wanted to know can I connect my laptop to the cell using USB and browse internet through that?? I have done it when I used GPRS but am not sure if it cn be done in this situation when the cell is connected toa wifi network..plz help..

Read the article
Source-control your BI Publisher reports

- by Dmitry Nefedkin

Version control systems (VCS) like Subversion, Git and the others has been widely adopted and became the must-have tool in any software development project. Source artifacts and checked out, modified, checked in, all the history of changes is tracked by the VCS. But what if the development tool stores the source/configuration artifacts not in your laptop's hard drive, but in some shared repository instead? Well, we definitely need a way for export/import our artifacts from/to this repository. Oracle BI Publisher report development approach is based on such a shared repository model (catalog), and starting from BI Publisher 11.1.1.5 Oracle ships Catalog Utility, which can be utilized to export/import the reports from the command line. To start using the BI Publisher Catalog Utility you should: Go to the file system of the server where BI Publisher binaries has been installed and locate the following file: <MW_HOME>/Oracle_BI1/clients/bipublisher/BIPCatalogUtil.zip Copy the file to your local filesystem and unzip it. I will refer to this unzipped directory as <BIP_CLIENT_DIR> below If you do not want to pass server BI Publisher server URL, username and password during each invocation, modify the corresponding values inside <BIP_CLIENT_DIR>/config/xmlp-client-config.xml Open the terminal window and go to <BIP_CLIENT_DIR>/bin Make sure that the following environment variables are set: JAVA_HOME, ORACLE_HOME Now it's time to run the utility: if you are on Linux - just run BIPCatalogUtil.sh and pass the parameters according to the utility documentation if you are on MS Windows the bad news are that the command script for MS Windows is missing, and support.oracle.com note 1333726.1 says that a temporary solution is "create a .cmd file by setting up a classpath and copying the same commands from the .sh script". The good news are that I've created this script already, please download the it from GitHub Hope you will find this utility useful during you day-by-day BI Publisher development.

Read the article
tracd multiple projects+nginx reverse proxy

- by Xeross

I am trying to setup nginx with a reverse proxy to tracd, however I only want to use 1 tracd. Now first here's my config for this domain server { listen 80; server_name bugs.XXXXXXXX.com; access_log /var/log/nginx/XXXXXXXX-bugtracker.access.log proxy; location / { rewrite ^/bugtracker/(.*)$ /$1; rewrite ^/bugtracker$ /; proxy_pass http://127.0.0.1:81/bugtracker/; proxy_redirect default; proxy_set_header Host $host; } location ~ /\.ht { deny all; } } As you can see there's the rewrite rules, because for some reason all the urls that tracd spews out are like /bugtracker/something. Now this is indeed caused by tracd just sending urls like it normally should however trac is at bugs.XXXXXXXX.com/ and not at bugs.XXXXXXXX.com/bugtracker. So how can I make tracd/trac display the (In this case) correct urls ?

Read the article
How can I diagnose a "502 Bad Gateway" response from an Apache/Tomcat configuration?

- by Structure

I just finished up configuring a fairly default configuration of Tomcat. My Apache configuration was pre-existing and post-tomcat it still has no issues. I am using mod_jk to (if I am saying this correctly) interface between Apache and Tomcat and have my conf files setup for my workers, etc. I put my test file (Simply: http://tomcat.apache.org/tomcat-4.1-doc/appdev/sample/web/hello.jsp) into my tomcat/webapps/ directory and then call it via http://localhost/test/hello.jsp. From here Apache returns a "502 Bad Gateway" response. I confirmed this via the Apache logs, but beyond that I have no idea how to diagnose the issue. I assume the 502 is because Tomcat did not respond. I'd like to confirm if Tomcat received the request, but cannot locate the log file. At this point I had thought my installation was complete, so not sure where to go from here. Any input would be appreciated.

Read the article
Active Directory Domain Services on remote VPS

- by Rob Angelier

I really need help with configuring Active Directory Domain Services on a remote VPS. Situation we have a remote Windows Server 2008R2 VPS and i just installed the Active Directory Domain Services Role. A DNS Server was also configured by default at the end of the Active Directory installation. Problem I can't get my Windows 7 machine to register itself to the domain i have just created Question What are the steps i have to take to test my Active Directory configuration, and how do i connect clients to this Domain? I can provide screenshots and more information if neccesary. looking forward to your replies! best regards, Rob Angelier

Read the article
Dell SC1435 always requires F1 at boot

- by David Mackintosh

I have a Dell PowerEdge SC1435 that has come back after doing duty at a partner site. I am trying to configure it for local use. The only problem I have with it is that every time it boots it always requres a manual F1 press after the POST sequence. The last thing it does is give me the opportunity to configure the BMC, and then it says: Press F1 to continue or press F2 for Setup It will wait there forever (well, at least an hour). Pressing F1 starts the OS booting. I can't see the setting in the BIOS which controls this and I can't find it in the documentation. What am I missing?

Read the article
Can't connect using Jail SFTP account

- by Fazal

I've been following this tutorial "Limiting Access with SFTP Jails on Debian and Ubuntu" and whilst I've had no errors setting it up, I've had issues on Ubuntu 10.04LTS logging in as a user on a virtualhost. I've changed my SSH port to 22022, and enter all the credentials when attempting to login. I ran these commands to add a user to the virtualhost: # useradd -d /srv/www/[domain] [username] # passwd [username] # usermod -G filetransfer [username] # chown [username]:[username] /srv/www/[domain]/public_html I should add that this is the only time I've setup the user they have no other /home directories or such. The directory that does exist is at /srv/www/example.com/public_html When I try using a desktop package such as cyberduck to login to the site, I keep getting a "Login failed with this username or password". I am completely lost as what to do next... The reason why I'm trying this method is because I want my clients to use SFTP and not FTP to upload files to their websites. Any help or direction is appreciated.

Read the article
HP CM2320 Printer crashes windows 2003 spooler in TS/Citrix

- by Stephane

Hello, I'm having a very annoying issue with an HP printer (CM2320): all of a sudden, any user who has that printer installed locally as default printer would crash any Windows 2003 terminal services or Citrix server (XenApp PS 4.5) as soon as he connect, causing the session to hang and other users to be unable to connect to the server. To restore functionality, an administrator has to connect to the server's console session and acknowledge the error message about spoolsv.exe having crashed with an AV. I tried downloading the latest drivers from HP (an adventure worthy of Lara Croft in itself) and install it on all servers but that didn't seem to have helped the situation: the spooler is still crashing. Anyone has a suggestion about what I could do about this ?

Read the article
b Is it bad to have the Reverse DNS for two IPs point to the same domain name?

- by Daniel Vandersluis

I am in the process of setting up a new server for my web application (the site will be moved, it is not for load balancing or the like), which has a different IP address from my existing server. My current server has a reverse DNS PTR record set up pointing its IP to mydomain.com. Is it bad to set up a reverse DNS PTR record for the new IP pointing to mydomain.com as well? Or should I wait until I do my migration to set up the record? Update: I forgot to mention, the A record for the mydomain.com points to the old server's IP address, not the new one, if it matters.

Read the article
CentOS package not available

- by Bastien974

I installed a CentOS 5.5 and the default php package is 5.1.6. I want to install 5.2.9, so I added /etc/yum.repo.d/CentOS-Testing.repo [c5-testing] name=CentOS-5 Testing baseurl=http://dev.centos.org/centos/$releasever/testing/$basearch/ enabled=0 gpgcheck=1 gpgkey=http://dev.centos.org/centos/RPM-GPG-KEY-CentOS-testing php-5.2.9-2.el5.centos.x86_64.rpm is available http://dev.centos.org/centos/5/testing/x86_64/RPMS/ So I tried: yum clean all, *yum search php-5.2.9-2.el5.centos.x86_64.rpm* -- Warning: No matches found for: php-5.2.9-2.el5.centos.x86_64.rpm What I am doing wrong ? Thanks for your help.

Read the article
Dlink DWA-643 ExpressCard / Atheros AR5008 can't connect to wifi networks

- by Justin Kelly

I've just purchased a D-Link DWA-643 Xtreme N ExpressCard Notebook Adapter - but it can't connect to my wireless network The card is listed on the FSF website and - refer links below: http://www.fsf.org/resources/hw/index_html/net/wireless/index_html/cards.html http://www.dlink.com.au/products/?pid=550 Ubuntu see the card as using the Atheros AR5008 chipset - refer image below The card lights up and I can see that available wifi networks using this card - so it seems to 'just work' on ubuntu 12.04 but when i try and connect to my networks - it fails I've tried setting the network to all the different options (WEP, WPA2, no encryption, etc.. b/g/n ) but ubuntu sill cant connect to it I've also installed wicd but still couldn't connect Has anyone got a DWA-643 to work in Ubuntu? Or does anyone have any suggestion on how to get it to connect?? Any help would be greatly appreciated Note: the laptop has built in wifi but its broadcom, works but with dialup speed connection - and i've had nothign but trouble using the boardcom drivers so purchased the FSF recommended PCI expresscard as i hoped it would 'just work' on the latest Ubuntu i've have tried to disable the built in wifi - broadcom - but even with the broadcom uninstall and unavailable it didnt help the dlink to connect previously I had MAC address filtering on the router - i've added the dlinks MAC - and also disabled MAC address filtering - still no luck lspci output below: 18:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) Subsystem: D-Link System Inc Device 3a6f Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at e4000000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath9k Kernel modules: ath9k

Read the article
Why does python easy install give me "permission denied" errors?

- by Golden Sinha

When i try to install program in ubuntu 12.04 it shows the error. program 1 : home@home-Compaq-610:~/Desktop$ python setup.py install running install running build running build_py creating build creating build/lib.linux-i686-2.7 copying Calculator.py - build/lib.linux-i686-2.7 running install_lib copying build/lib.linux-i686-2.7/Calculator.py - /usr/local/lib/python2.7/dist-packages error: /usr/local/lib/python2.7/dist-packages/Calculator.py: Permission denied . program 2 : home@home-Compaq-610:~/Desktop$ sudo chmod +x Moto.bin [sudo] password for home: home@home-Compaq-610:~/Desktop$ it shows like this but it do not install the program. program 3 : home@home-Compaq-610:~/Desktop$ python setup.py install [ERROR] wxPython2.8 is required. how to install wxPython2.8 please tell. if i try to install this program using easy_install it shows like this. home@home-Compaq-610:~/Desktop$ easy_install editra error: can't create or remove files in install directory The following error occurred while trying to add or remove files in the installation directory: [Errno 13] Permission denied: '/usr/local/lib/python2.7/dist-packages/test-easy-install-6778.pth' The installation directory you specified (via --install-dir, --prefix, or the distutils default setting) was: /usr/local/lib/python2.7/dist-packages/ Perhaps your account does not have write access to this directory? If the installation directory is a system-owned directory, you may need to sign in as the administrator or "root" account. If you do not have administrative access to this machine, you may wish to choose a different installation directory, preferably one that is listed in your PYTHONPATH environment variable. For information on other options, you may wish to consult the documentation at: http://packages.python.org/distribute/easy_install.html Please make the appropriate changes for your system and try again. home@home-Compaq-610:~/Desktop$ please help me . please tell how to install programs..

Read the article
where are flash settings stored locally on Ubuntu

- by Joseph Mastey

It's possible change flash settings on your computer at this URL: http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager03.html However, given that Macromedia has no problems setting LSO cookies on your HDD that you cannot find, I am a little bit skeptical that the settings I've tweaked there would be saved. So, I'd like to be able to look locally on my PC and verify the settings. Where can I find the settings for Flash locally? Surely the plugin cannot be heading to Macromedia itself for them (that is a future too bleak to contemplate). I am running Ubuntu 10.04. Thanks, Joe

Read the article
Hidden files in Nautilus after extracting ISO

- by Luis Alvarado

I need to first point to the image below to explain a bit about what I find weird here: I extracted the informacion from an ISO I from Nautilus I could only see two folders but from the terminal I can see the rest of the files and folders. This folders do not have the . character in from of them to hide them from plain sight. When I try to "Show hidden files" in Nautilus, Nautilus closes itself. It does not show the hidden folders or files. Somehow they are hidden without using the normal dot in the beginning of the name. The have my user permission but no way of seeing them from Nautilus. I can interact with them but the fact that they appear hidden when I can see them inside the ISO and after extracting them they disappear is what confuses me. What permission or setting makes this folders appear hidden and does not let Nautilus show them and like I said before, trying to show them with the "Show hidden files" option crashes Nautilus and exits it. Forcing me to have to open Nautilus again from the Launcher.

Read the article
How to pass a filename to a shortcut in Windows

- by Kendall Frey

I have a program program.exe and a document document.txt, and to open the document, I can drag document.txt onto program.exe. So far so good. Now I want to call it with a command-line parameter -param so that the full command line is program.exe -param document.txt Unfortunately, I can't do this with drag and drop, so I need to fire up cmd and type in the command manually. This takes too long, and I need an easier way. How can I create a shortcut that I can drop the file onto, and have it call the program with the command-line parameter? I tried setting the shortcut to program.exe -param "%1", but that didn't work, because it appeared to pass only the file name, and not the path, and since the current directory was the one with the program and not the one with the document, it couldn't find the document.

Read the article

< Previous Page | 729 730 731 732 733 734 735 736 737 738 739 740 | Next Page >