Search Results

Search found 3084 results on 124 pages for 'lan'.

Page 74/124 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

• Apache mod_setenvif Server_Addr

  - by user18330

  I have an Apache server in a DMZ, reachaable on the LAN from 192.168.1.1, public 123.456.789.123. I'm trying to get it to require authentication if the inbound hits are coming from the public side. This doesn't seem to work: SetEnvIf SERVER_ADDR 123.456.789.123 local_nic=1 <Location /junk> Order Deny,Allow AuthName "Access required" AuthType Basic AuthUserFile /etc/httpd/conf/htpasswd Require valid-user </Location> What am I doing wrong? Sorry, HTML tags were wiping out my Apache directives.

  Read the article

• Problem connecting to Ubuntu Server in same local network.

  - by frbry

  I have my LAN set up as below: 192.168.2.1: ADSL Router (DHCP Range: 192.168.2.2-192.168.2.250) 192.168.2.254: Wireless Access Point 192.168.2.253: Ubuntu Server (Static IP) 192.168.2.2: My Laptop (Connects to Internet via the Wireless AP) NAT in router is active and set up to transfer requests made over port 80 to 192.168.2.253. Router's firewall is inactive. No IPs in DMZ. My friends get Apache's It Works page when they try to enter http://my_external_ip. But I get Router's configuration page instead of that. What should I check or do? Thanks.

  Read the article

• How do you explain ethernet cable problems to non networking people?

  - by Bryan McLemore

  We've recently been doing a large network migration in our datacenter. We've had a few cables in this start to deliver really bad pings (in excess of 500ms on a LAN) before they could be replaced. The cables we were replacing weren't made the best. They where all hand made and the runs were so short on some of them that the bend radius was definitely too tight. Some of them ran in bundles right in front of the heat exhaust of the power supplies. The cables were running ok until we started pulling the ones surrounding them out. Then a few started having the problem I mentioned above degrading performance and causing reliability issues. I'm trying to figure out the best way to explain this to non networking people. Is there any documentation that people could recommend or other methods?

  Read the article

• Windows 2003 Server Intermittent DNS Issues

  - by Mike

  Looking for a little help here. I have a Windows 2003 DNS Server set up on our network. Lately computers on our LAN have been, at times, unable to resolve a certain sub domain for our website whereas other times the request is resolved just fine. During these periods of "downtime" all other network activity (i.e web sites, internal resolutions, network shares, etc.) remains normal. I can tell it is a problem with our DNS server because the resolution always works from outside our network. I'm hoping someone out there has experienced something similar or could at least offer me place to start troubleshooting. Thanks!

  Read the article

• How do I bridge a connection from Wi-Fi to TAP on Mac OS X? (for the emulator QEMU)

  - by penx

  I'm trying to setup a bridge between my Wi-Fi connection and an emulator (QEMU). I need a virtual machine to be on the same LAN as the host, with its own IP address. QEMU requires using a TAP (virtual network device) so I have installed tuntaposx, have it running, and can open up QEMU using a TAP: qemu-system-arm -kernel zImage.integrator -initrd arm_root.img -m 256 -net nic -net tap,ifname=tap1 -nographic -append "console=ttyAMA0" I have a script that configures the bridge once QEMU has opened up the TAP interface: sysctl -w net.link.ether.inet.proxyall=1 sysctl -w net.inet.ip.forwarding=1 sysctl -w net.inet.ip.fw.enable=1 ifconfig bridge0 create ifconfig bridge0 addm en1 ifconfig tap1 0.0.0.0 up ifconfig bridge0 addm tap1 ifconfig bridge0 up If I manually set an IP on the VM, I can ping from the VM to the host, but not from the host to the VM. Also, I can't access the rest of the network from the VM - including not being able to set an IP over DHCP. Any ideas?

  Read the article

• Rate of UDP packet loss over WLAN

  - by Martin

  While testing something with TFTP I noticed lots of timeouts (and slow speed as result) when I used my WLAN - and no problems when using a network cable. A quick test program sending/receiving UDP revealed that there are about 3-5% packets lost. While it's obvious that WLAN has to be less reliable than LAN, I have no knowledge what loss rates are considered 'normal' - and when there is a need to further investigate the network infrastructure. Are there 'typical' packet loss rates on WLAN (and other network technologies e.g. PowerLAN, WAN, ...? Thanks

  Read the article

• Best way to log internet traffic for office network via remote IP

  - by buzzmonkey

  We have a network of about 40 machines running either Win XP or 7 in our office via LAN switches into 1 x Netgear Router (WNDR3700). We have noticed recently that our local network has been added to the CBL Blacklist due to one of our machines being infected with Torpig. I have attempted to use Kaspersky's TDSSKiller Antirootkit Utility to find the infected machine but all appear to be clear. The CBL register advises to find the local machine which is connection to the remote IP address (CBL has provided the range). However, our router does not have the ability to block remote IP addresses - does anyone know of a software which can log all the internet traffic, which we can then use to find the infected machine.

  Read the article

• I need to somehow change my ip address

  - by tric

  hello. i`m in a lan using iptables/masquerade. what i want to do, is to login in a web application.i write my user and passwd and click login and everything is fine, but if i try to modify something in that aplication it tells me that i have a wrong ip address.i knwo for sure that this app only allows ip 10.3.x.x .how can i trick that application to think that i have an ip from class 10.3.x.x and not my wan ip? 10x sorry for my bad english!

  Read the article

• linux: upload / download difference on network shares

  - by Batsu

  I have a Red Hat Enterprise Linux 6 (with SELinux) which shows significant differences of speed between download and upload (the latter significantly slower) of files shared over the LAN. The bottleneck seems to be the output of the linux machine since I have a rate around 1Mb/s when WinXP machines download files shared (using samba) by the RHEL machine uploading files from the RHEL to a WinXP's shared folder while uploading from the XP machines to linux's shares downloading XPs' shares on the RHEL any share between Windows machines only run smooth (around 50Mb/s). Since the upload from RHEL to WinXP's share is slowed too I would exclude an issue in the configuration of samba. What could possibly determine this limit in the upload speed? update: iptables doesn't show any output rule and disabling it doesn't show any noticeable difference, so I would rule out it too.

  Read the article

• Block complete network access for one local user

  - by tumchaaditya

  Well, this is quite trivial question but I could not find a satisfactory answer even after trying many search queries both here and on Google. I want to share my PC with my room-mate. And I don't want him to access ANY network(LAN included). So, I can create an account for him and block network access for the same. I would prefer avoiding any third-party tools as far as possible. It's a simple home PC hooked up to a router for internet. No domain and other stuff. (Technically, guest account can achieve this. But somehow, the guest account on my PC has network access!)

  Read the article

• how to reinstall Asus notebook using Recovery DVD?

  - by Radek

  a friend of mine asked to reinstall his Asus notebook. He didn't want Vista anymore so I installed XP. Re-partitioned the hdd (no more recovery partition). Everything went fine except I cannot make LAN card work. I created a question for that. And I talked to Asus help desk but it didn't help so we decided to go back to Vista. I have the original Recovery DVD for his notebook. With files like ASUS.SWM and ASUS2.SWM. But I do not know how to use this DVD to reinstall his notebook. Did I mention that his DVD drive mostly doesn't work?

  Read the article

• backuppc - how to backup remote (over the internet) clients?

  - by Scott

  I am testing out backuppc, which works great so far backing up windows clients on a LAN via SMB (no backup client/agent required). However I have quite a few laptops and desktops that are in various remote locations - some of which move around. I need some way to have that remote computer create an outgoing connection for backup purposes (Windows XP/7). I know backuppc supports smb, rsync and 'tar', but I believe these are all connections going from the server TO the client. SO, I either need a way to vpn the client on a timed basis, or it would be a lot better if the client could some how connect to the server (ssh?) and initiate it's own backup somehow (rsync?). Of course this all needs to be pre-installed by me and require no maintenance by the end user, no dialogs on their side. What do you think?

  Read the article

• local .pac-file URL format that works with IE and Safari (Windows)?

  - by legr3c

  Say I want to use a proxy auto-config file that is stored at C:\proxy.pac. To make Internet Explorer use this configuration I have to specify the pac-file in the LAN settings in the following way: file://C:/proxy.pac But Safari, that uses the same proxy settings, will ignore it in this case. To make Safari use the pac-file I have to reference it as file:///C:/proxy.pac (3 slashes at the beginning) which, according to Wikipedia is the correct format. But this way Internet Explorer will ignore it. Opera and Chrome, that also use the same proxy settings, are fine with both ways but is there another option that will work with Safari and Internet Explorer at the same time?

  Read the article

• What virtualization solution should I try next, after hitting problems w/ VMWare Player in dual-netw

  - by Alex R

  I have been using VMWare Player 2.5 for a while (Ubuntu guest on Vista host, 32-bit). VMWare had worked great until now but then I hit a brick wall: Due to some reorganization of my home network, the host machine now has to use a wireless connection to reach the Internet, while the printer, fileserver, and other important stuff are attached to a local gigabit hub. I have tried several tricks, such as editing the .vmx file, changing settings in vmnetcfg, etc, but I'm still unable to get the virtual Ubuntu box to connect each of the two virtual NICs to different networks (I did get it to recognize two NICs, but both DHCP'd onto the gigabit LAN). So, I'm ready to dump vmware for something with a little more low-level control of network settings. Virtualization is such a crowded space, I could spend months evaluating every product out there. I'm hoping for a shortcut... Can anyone recommend the best VM for my situation described above? Thanks

  Read the article

• Configuring bridged network connection --- Windows 7 host, Ubuntu 10.04 guest --- VMWare Workstation 8

  - by H3br3wHamm3r81

  Here is my IPCONFIG /ALL from the host (Windows 7 64-bit): Here is my IFCONFIG from the guest (Ubuntu 10.04): To be honest, I don't have experience configuring a network between a host and a guest in VMWare (a virtual machine). I've searched high and low on the internet, but I haven't seen anything that can help. Perhaps I'm just not using the right keywords when I search. Nevertheless, does anyone here have any experience with establishing a network connection? Edit: One important note. I don't use DHCP to provide private addresses to the hosts on my LAN. I use "static" IP addresses on my internal network by configuring each IP address manually in the host's network configuration utility (I have TV's, XBOX 360, and a few PC's). I would like to configure the IP on the virtual machine guest manually as well. The reason is because my XBOX 360 only works properly using a static IP address. It will kick me off XBOX Live if it has one given by the router (via DHCP).

  Read the article

• Jumbo Frames on DIR-655

  - by Spookyone

  I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU Synology DS107+, Firmware 3.0-1337 Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

  Read the article

• Can irssi ignore the 24h dsl-reconnect

  - by mcnesium

  A couple of weeks ago I had to switch my ISP from cable to DSL. Now I have this ridiculous disconnect and reconnect every 24h. It's no big deal insofar as having a new IP address every day, but for one exception. Since I host my irssi screen on a machine inside the LAN, my history gets affected by the reconnect in terms of a topic announcement, the users in each channel, creation date and so on. It's about 10 lines of redundant content every day. This is annoying especially in channels with very little traffic, because you hardly see the actual content in line with the every-day-junk. So I was wondering if I can tell irssi to silently ignore the reconnection details, so that my only meta-content in each channel goes back to "Day changed to ...", like back in the days of cable-internet.

  Read the article

• Local Group Policy Editor reverting setting to default

  - by Timur Aydin

  On my Windows 7 Ultimate 32bit system, I have changed the following setting: Local Computer Policy - Computer Configuration - Windows Settings - Security Settings - Local Policies - User Right Assignment - Deny access to this computer from the network This setting was by default "Guest" and I deleted this so that Guest can access a defined network share over the LAN. But later, I have changed my mind and wanted to return this setting to its default. So I edited that setting and specified Guest. But the setting became MYWINPC\Guest. So my question is, what is the difference between the previous setting "Guest" and MYWINPC\Guest? And how do I return this setting to its default value, "Guest"?

  Read the article

• Multiple IPs from one router

  - by ergoen

  I would like to know if it is possible (and if so, how) to configure a router running dd-wrt (or openwrt) to supply connected devices with two ip addresses. The network looks like this: [Internet] | [Router] | | [Comp1] [Comp2] ... My ISP provides me with enough public IP adresses to give all devices on my network one each. The easiest way to set that up is to just use the router as a switch. This will however lead to problems with some LAN based applications. I would still like to use Samba-shares between the computers as well as a vpn server. What I am looking for basically is if it is possible to use the router as a DHCP server for a local network (let's say giving IP adresses 192.168.1.xx to connected computers) while at the same time passing through public IP addresses to each as well?

  Read the article

• Unable to do Port Forwarding in Virtual Box

  - by dewbot

  I'm using Mac OS X 10.6. I have installed Virtual Box 4.1.0 in it. My Guest OS is Ubuntu Server 11.04. I have added a rule in Port Forwarding in Virtual Box - "guestssh" TCP 127.0.1.1 8080 127.0.0.1 1337 Inside Guest OS I'm running nodejs server. Code is nothing but simple helloworld code found on their site http://nodejs.org/. In short I'm running server on 127.0.0.1 on 1337 Port. Now according to rule I have given, from Host Machine all the requests for 127.0.1.1:8080 should be forwarded to 127.0.0.1:1337 of Guest OS. From Host I'm doing curl http://127.0.1.1:8080 and I'm getting curl: (7) couldn't connect to host Is there something am I doing wrong? Note- Don't give me suggestion to do ssh n all. As my ISP does not provide Internal LAN so its not possible in my case. All I can do it Port Forwarding.

  Read the article

• How can I make my Ubuntu server accessible to the internet ?

  - by wahid

  Hi, I already installed applications to make my server web server. when I type the DHCP released ip address in the web browser, i can access it but all it says is "it works....etc". I can copy files to /var/www successfuly using WINSCP but yet, i can not see any files when I connect to it using my windows machine in the browser. Secondly , I tried to forward port on my home SMC router, it only accepts local lan ip which my ubuntu server picks up internet ip from router...what should i do ? can you help please ???? Thanks,

  Read the article

• Printing documents on HP printer very slow

  - by maxim

  I have a strange problem with HP drivers. I have configured a HP printer 2025dn with LAN connection, on 3 pc, using the cd rom of HP driver. All works well, but sometimes for certain documents the time for printing is very slow and long. I observe during this situation, in task manager, a process called rundll32.exe loads CPU at 100%. If I kill that process the printer starts printing fast the document in the queue. I wondering the reason of this strange behaviour.

  Read the article

• Windows Xp, Svchost.exe connecting to different ips with remote port 445

  - by Coll911

  Im using Windows Xp professional Sp2 Whenever i start my windows, svchost.exe starts connecting to all the possible ips on lan like from 192.168.1.2 to 192.168.1.200 The local port ranges from 1000-1099 and the remote port being 445. After its done with the local ips, it starts connecting to other random ips. I tried blocking connections to the port 445 using the local security polices but it didn't work Is there any possible way i could prevent svchost from connecting to these ips without involving any firewall installed ? since my pc slows down due to the load I'd be thankful for any advices

  Read the article

• How can I prevent OpenVPN Client from blocking inbound connections while a tunnel is connected?

  - by joshudson

  We have this machine that we RDP into for using OpenVPN. When a tunnel is connected, it is not possible to RDP into the machine. Should we get disconnected, this is a problem (machine is headless). How can I stop OpenVPN from blocking inbound RDP? I do not have access to the server configuration. If there's anything interesting on the client to check you'll have to tell me how to get at it. I eliminated the possibility of routing issue before asking the question. Only inbound connections cannot be opened. Outbound connections to LAN can be opened just fine. EDIT: Don't bother answering. The problem disappeared without any known changes being made.

  Read the article

• Laptop with Windows 7 turns on spontaneously while being in "Sleep" state

  - by alexb

  I own a laptop(HP Pavilion DV7) with Windows 7 installed for already half a year. Usually when I finish my work I do not turn machine off - closing is enough to get is into "Sleep" state. Generally it's okay for me, but recent several days laptop was turning on in night spontaneously, while I was sleeping. I haven't installed any app with "turn-on by schedule on when_dooes_pc_wants"-like features. Checked if there are some "Wake-On-Lan"-like settings in BIOS, haven't found ones. The power-cable is always plugged-in. Does someone have any suggestions regarding that? p.s. laptop is placed right near by bed, so when it turns-on on night - it is quite annoying and a bit scary. I think it's trolling me, please help to stop it :) Thanks.

  Read the article

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >