Search Results

Search found 2637 results on 106 pages for 'mount smbfs'.

Page 74/106 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

• Getting FC11 to run under VMware Server, converted from physical machine

  - by Kristian

  I have a FC11 installation that I have converted to a VMware disk image to run om my VMware Server. I converted it with qemu-img, as the VMware Converter software apparently only converts Linux hosts to VMware Infrastructure servers. The disk image boots fine (grub is loaded and boots the kernel) but it seems like the disk is not found by the kernel, and the boot process stalls. Hotplugging USB devices work (the kernel prints debug information) and I'm able to press keys (Ctrl-Alt-Delete for instance). The VMware guest OS is set to RedHat Enterprise Linux 5 (32 bit), and I have tried both the LSI Logic, LSI Logic SAS and VMware Accelerated SCSI SCSI controllers, to no avail. I'm able to boot an installer disk and get into rescue mode and mount the filesystem, so my question is, what do I need to do to the guest kernel / initrd image to make it recognize the virtual disk?

  Read the article

• On boot firmware request for intel GMA 3100 chipset timing out

  - by Yannick M.

  I am currently in the process of installing a Gentoo linux box with a Vanilla 2.6.29-r5 kernel with gentoo-xen-kernel patches in order to run the Xen Hypervisor. After rebooting with the new kernel, the booting process seemed to hang on: [ 0.863005] platform microcode: firmware: requesting intel-ucode/06-0f-07 [ 60.863442] Microcode Update Driver: v2.00-xen <[email protected]>, Peter Oruba Apparently the firmware request times out after 60 seconds (/sys/class/firmware/timeout) and booting just continues. I have done some research and have found that on RHEL-4 this problem was related to the mount of /sys changed and the firmware.agent hotplug script couldn't parse the line correctly. However I am having some difficulty tracking down how to fix this on Gentoo. Any and all ideas are greatly appreciated! Thanks

  Read the article

• Perl throwing 403 errors!

  - by Jamie

  When I first installed Perl in my WAMP setup, it worked fine. Then, after installing ASP.net, it began throwing 403 errors. Here's my ASP.net config: Load asp.net module LoadModule aspdotnet_module "modules/mod_aspdotnet.so" Set asp.net extensions AddHandler asp.net asp asax ascx ashx asmx aspx axd config cs csproj licx rem resources resx soap vb vbproj vsdisco webinfo # Mount application AspNetMount /asp "c:/users/jam/sites/asp" # ASP directory alias Alias /asp "c:/users/jam/sites/asp" # Directory setup <Directory "c:/users/jam/sites/asp"> # Options Options Indexes FollowSymLinks Includes +ExecCGI # Permissions Order allow,deny Allow from all # Default pages DirectoryIndex index.aspx index.htm </Directory> # aspnet_client files AliasMatch /aspnet_client/system_web/(\d+)_(\d+)_(\d+)_(\d+)/(.*) "C:/Windows/Microsoft.NET/Framework/v$1.$2.$3/ASP.NETClientFiles/$4" # Allow ASP.net scripts to be executed in the temp folder <Directory "C:/Windows/Microsoft.NET/Framework/v*/ASP.NETClientFiles"> Options FollowSymLinks Order allow,deny Allow from all </Directory> Also, what are the code tags for this site?

  Read the article

• Image file can't be opened by windows store app if the file is in the Ext4's external hard disk

  - by ? ?

  My question is described below: I have two disks, external hard disk and removable disk. They are formatted with EXT4. I put the same image in the disks, and use Ext2Fsd to mount the disks. I open the file in win8, and it will default open by the windows store app : photos. It will be success to open if the file is in the Ext4's removable disk. It will be failed to open if the file is in the Ext4's external hard disk. I don't know why it will be failed to open if the file is in the Ext4's external hard disk. Does anyone have similar experiences?

  Read the article

• UPS recommendations for three grey boxes?

  - by Margaret

  Hey all We have a series of grey-box style computers acting as servers at my workplace (rather than rack-mount). We were looking to get Uninterruptible Power Supplies for them. However, I'm not sure how many at what capacity are required. I'd assume it would be a good idea to hook the peripherals in as well - there's a 18.5" LCD monitor with a KVM, along with a couple of USB hard drives that require power. I currently have the most vital machine hooked up to a cheap (temporary) UPS, but it's probably close to worse than nothing. I'm looking for reasonable value for money, though I can probably negotiate with my boss on price range. I recognise that I may well need to buy two (or even three) UPSs to support the three machines. Any recommendations?

  Read the article

• Windows 2008 R2 DS in 2003 domain?

  - by 3molo

  Hi, Having a master domain controller running Windows 2003, and now I'd like to set up a new domain controller on a branch office. I really only have access to licenses for Windows 2008 R2 (through licensing.microsoft.com), so question is if a newly installed Windows 2008 Standard R2 can become a domain controller in the existing (2003) domain? First I tried adprep /forestprep on the newly installed 2008, but it complained about not being a domain controller. I then tried dcpromo, but it too complained about it. According to MS documentation, it seems I have to run 'adprep /forestprep' on the master domain controller, and adprep is located in 2008 installation DVD. Am I on the right track? Is the correct way to mount the 2008 installation dvd into the existing 2003 master controller, and run 'adprep /forestprep' on it there? Will I be able to run dcpromo on the 2008 once that has been completed? Thanks,

  Read the article

• Virtual fiber channel HBA in Solaris

  - by Phil

  We are trying to set up some virtual Fibre Channel HBA's in Solaris. This seems to be possible with NPIV. Creating NPIV's in a Solaris global zone works fine, but passing that NPIV to a zone didn't work at all. We tried to pass the NPIV as following: # zonecfg -z zone1 'info' zonename: studentz1 [...] device: match: /devices/pci@0,0/pci8086,25f9@6/pci8086,350c@0,3/pci1077,140@4/fp@1,0:devctl allow-partition not specified allow-raw-io not specified Wat we want to do is, set up an environment for SAN exercises. We don't have a physical host per student, so we try to virtualise that in some way (Solaris zones or VMware). It should be possible to display the WWN of the virtual HBA and mount the storage presented by the disk subsystem. Any ideas to pass the NPIV to a solaris zone or to virtualise this with vmware?

  Read the article

• Internal USB A Female to motherboard 4-pin that mounts internally

  - by rockinthesixstring

  I'm wondering if anyone knows of a product like this but that is physically mountable internally rather than on a cable? I'm planning on building a super low profile "gateway" pc that is dedicated to handling internet traffic in my home. I have a great 1U rackmountable chassis for an ITX motherboard, but I need the hard drive real estate for the additional NIC required to run a gateway (one onboard and one PCI). So the plan is to use a small 8GB USB Jump Drive for the OS inside the box (as to not have one hanging out the back. And although it's racked, I still don't want the jump drive flopping around internally, so I want it fixed somehow. I have an alternative idea where by I use a flush mount zap strap saddle and a zip tie to hold it in place, but that seems kind of like a hack.

  Read the article

• TrueCrypt Failing to Decrypt External Hard Drive after changing Enclosures

  - by Anx Ara

  I have a 4TB external hard drive that was previously encrypted using TrueCrypt. The power source on the hard drive enclosure failed, so I had to switch the hard drive itself into a new enclosure. I can no longer decrypt the hard drive using TrueCrypt, as it says my password is wrong. I am certain that I entering the correct password. Additionally, in TrueCrypt, when I try to mount the volume under "Select Device", it shows the following: Harddisk 5: 3.6TB Device\Harddisk5\Partition 1 H: 465GB Whereas before I changed the enclosure it would show: Harddisk 5: 3.6TB Device\Harddisk5\Partition 1 H: 3.6TB I am on a Windows 8 PC and using TrueCrypt 7.1a. How can I get it to decrypt properly?

  Read the article

• What are my options with a downloaded Rackspace cloud image?

  - by schnippy

  I've got an unresponsive Rackspace slice that has defied all attempts at accessing. I created an emergency image from this and deleted it, downloading the files that compromise the image to a local source. There are a number of files / assets I would still like to recover from this server if possible but not sure exactly what I can do with the image files, if anything. Here's the files I have, for what its worth: emergency_########_######_cloudserver########.tar.gz.0 (5gb) emergency_########_######_cloudserver########.tar.gz.1 (5gb) emergency_########_######_cloudserver########.tar.gz.2 (5gb) emergency_########_######_cloudserver########.tar.gz.3 (50mb) emergency_########_######_cloudserver########.yml (25kb) Is it possible to mount this image as a drive? Are there other forensic recovery options?

  Read the article

• Lost HDD partition to clean command, testdisk unresponsive

  - by Sujay Anjankar

  I accidentally cleaned my external HDD by the clean command in Diskpart and got a full sized heart attack after that. I did some research and I have tried a number of tools already. To name a few: Testdisk Recuva Partition Find and mount Eassos Recovery I have even tried some other dumb sounding tools, but none of them could find the lost partition. They just show "no partition found". Testdisk shows Partition sector doesn't have the endmark 0xAA55. The file recovery softwares list the files, but none of them seem to be able to restore the lost partition. I need to recover the disk as it was. Any help would be much appreciated!

  Read the article

• Zero-channel RAID for High Performance MySQL Server (IBM ServeRAID 8k) : Any Experience/Recommendati

  - by prs563

  We are getting this IBM rack mount server and it has this IBM ServeRAID8k storage controller with Zero-Channel RAID and 256MB battery backed cache. It can support RAID 10 which we need for our high performance MySQL server which will have 4 x 15000K RPM 300GB SAS HDD. This is mission-critical and we want as much bandwidth and performance. Is this a good card or should we replace with another IBM RAID card? IBM ServeRAID 8k SAS Controller option provides 256 MB of battery backed 533 MHz DDR2 standard power memory in a fixed mounting arrangement. The device attaches directly to IBM planar which can provide full RAID capability. Manufacturer IBM Manufacturer Part # 25R8064 Cost Central Item # 10025907 Product Description IBM ServeRAID 8k SAS - Storage controller (zero-channel RAID) - RAID 0, 1, 5, 6, 10, 1E Device Type Storage controller (zero-channel RAID) - plug-in module Buffer Size 256 MB Supported Devices Disk array (RAID) Max Storage Devices Qty 8 RAID Level RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 1E Manufacturer Warranty 1 year warranty

  Read the article

• Recover Time Machine partition that turned MBR only instead of GUID

  - by alex

  I have one drive that has a NTFS partition, a TimeMachine partition (I guess HFS+) and empty space. The other day, I did one partition more from Windows 8 (bootcamp) and since then, I can't see the TimeMachine one from OSX, I can see it from Windows though. The problem is that TimeMachine uses a file system that Windows cannot browse, only shows some folders and I need to recover this partition because I have to use it to backup my Mac. On OSX I can only see the NTFS partition and the other one appears unmounted and it's impossible to mount. I've come to the conclusion that something has happened to the partition table. With TestDisk it shows that it's MBR only when I think it should be GUID: And pressing p shows that it's FDisk_partition_scheme and the TimeMachine one appears as Windows_NTFS. I found this thread that is similar to what it's happening to me: Adding NTFS partition to disk in Windows makes HFS+ partition on same disk invisible in Mac OS X

  Read the article

• Ubuntu dpkg error , after crash and filesystem error recovery

  - by Radian

  Ubuntu recently crashed , causing it's partition damaged ( which is EXT4) and Ubuntu was unable to boot , because it couldn't mount anything , only displays Busybox So I used the Live CD to run fsck on the partition, which fixed it , but deleted some nodes Now Ubuntu is working , but some files were missing , for example I lost the Panels configurations and Chromium's Extensions The Most Annoying problem , that there is some files corrupted , for example when I try to install any program, I got this (Reading database ... 95%dpkg: unrecoverable fatal error, aborting: files list file for package 'libservlet2.4-java' is missing final newline I tried these commands dpkg --configure -a apt-get -f install and from GUI , Synaptic Package Manager Fix Broken Packages So this file "libservlet2.4-java" Does anyone knows what it does ! and where it's location ? and how can I fix/get-correct-version-of it ? Also , is there any way I could tell Ubuntu to Check for ALL it's file , and if there is something corrupted it should recover it form the CD ?

  Read the article

• Best way to rip DVD movies to ISO files

  - by alex

  I'm trying to backup my DVD collection. I have Handbrake, and will eventually experiment with the best settings to use. For now, I'd like to backup the DVD's to ISO files, that i can mount and then use Handbrake on later, or burn back on to DVD should the original get damaged. I have a WD TV box that is capable of playing ISO files also. What's the best program for doing this? I'm not so much concerned with file size.

  Read the article

• vSphere ESX 5.5 hosts cannot connect to NFS Server

  - by Gerald

  Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

  Read the article

• Can unexpected power loss harm a Linux install?

  - by Johan Elmander

  I am developing an application on a Linux embedded board (runs Debian) e.g. Raspberry Pi, Beagle Board/Bone, or olimex. The boards works on an environment that the electricity is cut unexpectedly (it is far complicated to place PSU, etc.) and it would happen every day couple times. I wonder if the unexpected power cuts would cause crash/problem on the Linux Operation System? If it is something that I should worry, what would you suggest to prevent the damages on OS against the unexpected power cuts? PS. The application needs to writes some data to the storage medium (SD card), I think it would not be suitable to mount it as read-only.

  Read the article

• Use Internet Explorer 6 and 7 in Virtual Box.

  - by Sharon

  Hello. I am trying to install the vhds (virtual hard drive image) of IE6 on XP and IE 7 on XP packs available from Microsoft on Virtual Box. Virtual Box will only mount CD/DVD's and/or ISO's. How do I get it to use the Microsoft files? I need this to test web pages in IE6/IE7s. I am running Windows 7 Home Premium. Is there a way to do this, or another way that will allow me to load XP/IE6 and XP/IE7 in Virtualbox Edit: Ok I got it to work but it says XP must be updated in 3 days due to hardware changes. Microsoft said this would be activated til January 1st 2010. Is there a way to bypass that?

  Read the article

• How to add a web folder via command line (Windows)

  - by Ryan

  I am trying to add a web folder via command line in windows. At first I though I should use the "net use" command, but when I tried I kept getting System error 67: C:net use * http://dev.subdomain.domain.tdl/dav/ the user name for 'dev.restech.niu.edu': correctusername the password for dev.restech.niu.edu: System error 67 has occurred. The network name cannot be found. The url I used works in a browser. It's an Apache dav on basic auth LDAP authentication method being used. Here's the thing... I CAN create a web folder when I use the "Add a network place" wizard. When I do net use, I don't see it listed in the prompt that follows. What utility do I need to use to mount a web folder in command line?

  Read the article

• MySQL & tmpfs : performance

  - by Serty Oan

  I was wondering if, and how much, using tmpfs could improve MySQL performance and how it should be done ? My guess would be to do mount -t tmpfs -o size=256M /path/to/mysql/data/DatabaseName, and to use the database normally but maybe I'm wrong (I'm using MyISAM tables only). Will a hourly rsync between the tmpfs /path/to/mysql/data/DatabaseName and /path/to/mysql/data/DatabaseName_backup penalize performances ? If so, how should I make the backup of the tmpfs database ? So, is it a good way to do things, is there a better way or am I losing my time ?

  Read the article

• Options for installing software on Amazon EC2 Windows instances

  - by gareth_bowles

  I've been running Linux servers on Amazon EC2 for a while now; the experience has been great. I've recently needed to bring up a Windows server to run some Windows-only software that our product needs to use, and am running into a problem figuring out how to install the software, which is only available on DVD. With Linux I can just install packages from a Web-based repository and take advantage of EC2's fast network throughput, but so far on the Windows instance I've had to upload my ISO images to EC2 and mount them from the Windows EC2 instance. For some reason I'm getting really slow upload speeds to EC2, even though the regular upload speed from our office is pretty good (around 7Mbps). I've also tried mounting the DVD drive on my machine as a local drive on the EC2 instance via Remote Desktop, and then running the software install from the local drive, but I run into the same slow upload speed issue. Does anyone have a better way to install software from physical media onto an EC2 instance ?

  Read the article

• How to make TimeMachine back up contents of any path or mounted volume

  - by Olfan

  I keep different types of data in different encrypted sparsebundle images (say, one for each client) which automatically mount upon login but can't be opened by anybody other than myself. So, after login I have a number of virtual volumes in /Volumes/ which keeps my client data both secure and organized. How do I include data inside these virtual Volumes in TimeMachine's backups, or data residing in any path on any partition/volume? I found a promising solution description at blog.eurocomp.info involving editing the com.apple.TimeMachine.plist but all I can get TimeMachine to do is backing up the sparsebundle files themselves. I want it to back up the files inside the mounted image, though - something like adding /Volumes/Client_abc/ to TimeMachine's search path. Please do not redirect my to this previous question as it doesn't solve the problem at all. Please also refrain from telling me why you think I should not want this answer as that will not solve anything either. Please lastly don't say "it can't be done" unless you can technically prove that claim.

  Read the article

• How do I enable write access for an sFTP only user under Ubuntu?

  - by Jon Cage

  I'm running Ubuntu 12.04 and am trying to configure a user to allow chroot'd sFTP connections to another section of the filesystem. I've added the following to my /etc/ssh/sshd_config file: Match Group mygroup X11Forwarding no AllowTcpForwarding no ForceCommand internal-sftp ChrootDirectory /home/%u I've set their home directory so that it's owned by root but has their group. I've created a mount --bind from /home/myuser/transfers to /my/filesystem which appears to be navigable. The problem I'm having is that I'm not able to write to any part of the filesystem which makes this pretty useless as an FTP server. What am I missing? What can I check?

  Read the article

• Unable to access intel fake RAID 1 array in Fedora 14 after reboot

  - by Sim

  Hello everyone, 1st I am relatively new to linux (but not to *nix). I have 4 disks assembled in the following intel ahci bios fake raid arrays: 2x320GB RAID1 - used for operating systems md126 2x1TB RAID1 - used for data md125 I have used the raid of size 320GB to install my operating system and the second raid I didn't even select during the installation of Fedora 14. After successful partitioning and installation of Fedora, I tried to make the second array available, it was possible to make it visible in linux with mdadm --assembe --scan , after that I created one maximum size partition and 1 maximum size ext4 filesystem in it. Mounted, and used it. After restart - a few I/O errors during boot regarding md125 + inability to mount the filesystem on it and dropped into repair shell. I commented the filesystem in fstab and it booted. To my surprise, the array was marked as "auto read only": [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active (auto-read-only) raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# and the partition in it was not available as device special file in /dev: [root@localhost ~]# ls -l /dev/md125* brw-rw---- 1 root disk 9, 125 Jan 6 15:50 /dev/md125 [root@localhost ~]# But the partition is there according to fdisk: [root@localhost ~]# fdisk -l /dev/md125 Disk /dev/md125: 1000.2 GB, 1000202043392 bytes 19 heads, 10 sectors/track, 10281682 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1b238ea9 Device Boot Start End Blocks Id System /dev/md125p1 2048 1953519615 976758784 83 Linux [root@localhost ~]# I tried to "activate" the array in different ways (I'm not experienced with mdadm and the man page is gigantic so I was only browsing it looking for my answer) but it was impossible - the array would still stay in "auto read only" and the device special file for the partition it will not be in /dev. It was only after I recreated the partition via fdisk that it reappeared in /dev... until next reboot. So, my question is - How do I make the array automatically available after reboot? Here is some additional information: 1st I am able to see the UUID of the array in blkid: [root@localhost ~]# blkid /dev/sdc: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sdd: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/md126p1: UUID="60C8D9A7C8D97C2A" TYPE="ntfs" /dev/md126p2: UUID="3d1b38a3-b469-4b7c-b016-8abfb26a5d7d" TYPE="ext4" /dev/md126p3: UUID="1Msqqr-AAF8-k0wi-VYnq-uWJU-y0OD-uIFBHL" TYPE="LVM2_member" /dev/mapper/vg00-rootlv: LABEL="_Fedora-14-x86_6" UUID="34cc1cf5-6845-4489-8303-7a90c7663f0a" TYPE="ext4" /dev/mapper/vg00-swaplv: UUID="4644d857-e13b-456c-ac03-6f26299c1046" TYPE="swap" /dev/mapper/vg00-homelv: UUID="82bd58b2-edab-4b4b-aec4-b79595ecd0e3" TYPE="ext4" /dev/mapper/vg00-varlv: UUID="1b001444-5fdd-41b6-a59a-9712ec6def33" TYPE="ext4" /dev/mapper/vg00-tmplv: UUID="bf7d2459-2b35-4a1c-9b81-d4c4f24a9842" TYPE="ext4" /dev/md125: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sda: TYPE="isw_raid_member" /dev/md125p1: UUID="420adfdd-6c4e-4552-93f0-2608938a4059" TYPE="ext4" [root@localhost ~]# Here is how /etc/mdadm.conf looks like: [root@localhost ~]# cat /etc/mdadm.conf # mdadm.conf written out by anaconda MAILADDR root AUTO +imsm +1.x -all ARRAY /dev/md1 UUID=89f60dee:e46a251f:7475814b:d4cc19a9 ARRAY /dev/md126 UUID=a8775c90:cee66376:5310fc13:63bcba5b ARRAY /dev/md125 UUID=b9a1149f:ae114fc8:a6000d77:354dc42a [root@localhost ~]# here is how /proc/mdstat looks like after I recreate the partition in the array so that it becomes available: [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# Detailed output regarding the array in subject: [root@localhost ~]# mdadm --detail /dev/md125 /dev/md125: Container : /dev/md127, member 0 Raid Level : raid1 Array Size : 976759808 (931.51 GiB 1000.20 GB) Used Dev Size : 976759940 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 2 Update Time : Fri Jan 7 00:38:00 2011 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 30ebc3c2:b6a64751:4758d05c:fa8ff782 Number Major Minor RaidDevice State 1 8 32 0 active sync /dev/sdc 0 8 48 1 active sync /dev/sdd [root@localhost ~]# and /etc/fstab, with /data commented (the filesystem that is on this array): # # /etc/fstab # Created by anaconda on Thu Jan 6 03:32:40 2011 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg00-rootlv / ext4 defaults 1 1 UUID=3d1b38a3-b469-4b7c-b016-8abfb26a5d7d /boot ext4 defaults 1 2 #UUID=420adfdd-6c4e-4552-93f0-2608938a4059 /data ext4 defaults 0 1 /dev/mapper/vg00-homelv /home ext4 defaults 1 2 /dev/mapper/vg00-tmplv /tmp ext4 defaults 1 2 /dev/mapper/vg00-varlv /var ext4 defaults 1 2 /dev/mapper/vg00-swaplv swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 [root@localhost ~]# Thanks in advance to everyone that even read this whole issue :-)

  Read the article

• NTFS write speed really slow (<15MB/s) on Ubuntu

  - by Zulakis

  When copying large files or testing writespeed with dd, the max writespeed I can get is about 12-15MB/s on drives using the NTFS filesystem. I tested multiple drives (all connected using SATA) which all got writespeeds of 100MB/s+ on Windows or when formatted with ext4, so it's not an alignment or drive issue. top shows high cpu usage for the mount.ntfs process. AMD dual core processor (2.2 GHz) Kernel version: 3.5.0-23-generic Ubuntu 12.04 ntfs-3g version: both 2012.1.15AR.1 (Ubuntu default version) and 2013.1.13AR.2 How can I fix the writespeed?

  Read the article

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >