Search Results

Search found 4620 results on 185 pages for 'serial over lan'.

Page 74/185 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

• wifi hardware switch doesn't work on a Dell 1018

  - by user42566

  I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

  Read the article

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Errors when trying to compile the driver for the rtl8192su wireless adapter

  - by Tom Brito

  I have a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g sudo lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) sudo lsusb Bus 002 Device 003: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer, Inc. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Organization &amp; Architecture UNISA Studies &ndash; Chap 6

  - by MarkPearl

  Learning Outcomes Discuss the physical characteristics of magnetic disks Describe how data is organized and accessed on a magnetic disk Discuss the parameters that play a role in the performance of magnetic disks Describe different optical memory devices Magnetic Disk The way data is stored on and retried from magnetic disks Data is recorded on and later retrieved form the disk via a conducting coil named the head (in many systems there are two heads) The writ mechanism exploits the fact that electricity flowing through a coil produces a magnetic field. Electric pulses are sent to the write head, and the resulting magnetic patterns are recorded on the surface below with different patterns for positive and negative currents The physical characteristics of a magnetic disk   Summarize from book   The factors that play a role in the performance of a disk Seek time – the time it takes to position the head at the track Rotational delay / latency – the time it takes for the beginning of the sector to reach the head Access time – the sum of the seek time and rotational delay Transfer time – the time it takes to transfer data RAID The rate of improvement in secondary storage performance has been considerably less than the rate for processors and main memory. Thus secondary storage has become a bit of a bottleneck. RAID works on the concept that if one disk can be pushed so far, additional gains in performance are to be had by using multiple parallel components. Points to note about RAID… RAID is a set of physical disk drives viewed by the operating system as a single logical drive Data is distributed across the physical drives of an array in a scheme known as striping Redundant disk capacity is used to store parity information, which guarantees data recoverability in case of a disk failure (not supported by RAID 0 or RAID 1) Interesting to note that the increase in the number of drives, increases the probability of failure. To compensate for this decreased reliability RAID makes use of stored parity information that enables the recovery of data lost due to a disk failure.   The RAID scheme consists of 7 levels…   Category Level Description Disks Required Data Availability Large I/O Data Transfer Capacity Small I/O Request Rate Striping 0 Non Redundant N Lower than single disk Very high Very high for both read and write Mirroring 1 Mirrored 2N Higher than RAID 2 – 5 but lower than RAID 6 Higher than single disk Up to twice that of a signle disk for read Parallel Access 2 Redundant via Hamming Code N + m Much higher than single disk Highest of all listed alternatives Approximately twice that of a single disk Parallel Access 3 Bit interleaved parity N + 1 Much higher than single disk Highest of all listed alternatives Approximately twice that of a single disk Independent Access 4 Block interleaved parity N + 1 Much higher than single disk Similar to RAID 0 for read, significantly lower than single disk for write Similar to RAID 0 for read, significantly lower than single disk for write Independent Access 5 Block interleaved parity N + 1 Much higher than single disk Similar to RAID 0 for read, lower than single disk for write Similar to RAID 0 for read, generally  lower than single disk for write Independent Access 6 Block interleaved parity N + 2 Highest of all listed alternatives Similar to RAID 0 for read; lower than RAID 5 for write Similar to RAID 0 for read, significantly lower than RAID 5  for write   Read page 215 – 221 for detailed explanation on RAID levels Optical Memory There are a variety of optical-disk systems available. Read through the table on page 222 – 223 Some of the devices include… CD CD-ROM CD-R CD-RW DVD DVD-R DVD-RW Blue-Ray DVD Magnetic Tape Most modern systems use serial recording – data is lade out as a sequence of bits along each track. The typical recording used in serial is referred to as serpentine recording. In this technique when data is being recorded, the first set of bits is recorded along the whole length of the tape. When the end of the tape is reached the heads are repostioned to record a new track, and the tape is again recorded on its whole length, this time in the opposite direction. That process continued back and forth until the tape is full. To increase speed, the read-write head is capable of reading and writing a number of adjacent tracks simultaneously. Data is still recorded serially along individual tracks, but blocks in sequence are stored on adjacent tracks as suggested. A tape drive is a sequential access device. Magnetic tape was the first kind of secondary memory. It is still widely used as the lowest-cost, slowest speed member of the memory hierarchy.

  Read the article

• Wireless cycling between connected and disconnected

  - by Tony Kilgore

  My friend has a Acer Aspire 5733Z-4851 it keeps disconnecting and connecting to his wifi but his hard wire will run just fine. Any suggestions? All the codes: lspci: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) lsmod: Module Size Used by snd_seq_dummy 12798 0 rfcomm 46619 0 bnep 18140 2 bluetooth 209199 10 rfcomm,bnep parport_pc 32688 0 ppdev 17073 0 lp 17759 0 parport 46345 3 parport_pc,ppdev,lp binfmt_misc 17500 1 ums_realtek 17949 0 snd_hda_codec_realtek 77876 1 uas 17844 0 coretemp 13400 0 snd_hda_intel 33491 4 snd_hda_codec 134212 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 96580 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30512 1 snd_seq_midi uvcvideo 76749 0 videobuf2_core 32851 1 uvcvideo videodev 120309 2 uvcvideo,videobuf2_core videobuf2_vmalloc 12860 1 uvcvideo videobuf2_memops 13368 1 videobuf2_vmalloc snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61521 3 snd_seq_dummy,snd_seq_midi,snd_seq_midi_event snd_timer 29425 2 snd_pcm,snd_seq arc4 12529 2 snd_seq_device 14497 4 snd_seq_dummy,snd_seq_midi,snd_rawmidi,snd_seq psmouse 95552 0 ath9k 131308 0 tg3 148780 0 snd 78734 17 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device microcode 22803 0 mac80211 539908 1 ath9k ath9k_common 14055 1 ath9k ath9k_hw 395218 2 ath9k,ath9k_common ath 23827 3 ath9k,ath9k_common,ath9k_hw i915 520629 3 soundcore 15047 1 snd serio_raw 13215 0 cfg80211 206566 3 ath9k,mac80211,ath snd_page_alloc 18484 2 snd_hda_intel,snd_pcm intel_ips 18049 0 lpc_ich 17061 0 drm_kms_helper 46784 1 i915 drm 275528 4 i915,drm_kms_helper mei 40690 0 i2c_algo_bit 13413 1 i915 joydev 17457 0 acer_wmi 32453 0 sparse_keymap 13890 1 acer_wmi mxm_wmi 12979 0 mac_hid 13205 0 wmi 19070 2 acer_wmi,mxm_wmi video 19335 2 i915,acer_wmi usb_storage 48838 1 ums_realtek sudo lshw -C network: *-network description: Ethernet interface product: NetLink BCM57780 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: b8:70:f4:9a:35:b6 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=half firmware=sb latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:44 memory:d3400000-d340ffff[/QUOTE][QUOTE]*-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 68:a3:c4:eb:60:7d width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-19-generic firmware=N/A ip=192.168.0.168 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d2400000-d240ffff)

  Read the article

• SQL Server Optimizer Malfunction?

  - by Tony Davis

  There was a sharp intake of breath from the audience when Adam Machanic declared the SQL Server optimizer to be essentially "stuck in 1997". It was during his fascinating "Query Tuning Mastery: Manhandling Parallelism" session at the recent PASS SQL Summit. Paraphrasing somewhat, Adam (blog | @AdamMachanic) offered a convincing argument that the optimizer often delivers flawed plans based on assumptions that are no longer valid with today’s hardware. In 1997, when Microsoft engineers re-designed the database engine for SQL Server 7.0, SQL Server got its initial implementation of a cost-based optimizer. Up to SQL Server 2000, the developer often had to deploy a steady stream of hints in SQL statements to combat the occasionally wilful plan choices made by the optimizer. However, with each successive release, the optimizer has evolved and improved in its decision-making. It is still prone to the occasional stumble when we tackle difficult problems, join large numbers of tables, perform complex aggregations, and so on, but for most of us, most of the time, the optimizer purrs along efficiently in the background. Adam, however, challenged further any assumption that the current optimizer is competent at providing the most efficient plans for our more complex analytical queries, and in particular of offering up correctly parallelized plans. He painted a picture of a present where complex analytical queries have become ever more prevalent; where disk IO is ever faster so that reads from disk come into buffer cache faster than ever; where the improving RAM-to-data ratio means that we have a better chance of finding our data in cache. Most importantly, we have more CPUs at our disposal than ever before. To get these queries to perform, we not only need to have the right indexes, but also to be able to split the data up into subsets and spread its processing evenly across all these available CPUs. Improvements such as support for ColumnStore indexes are taking things in the right direction, but, unfortunately, deficiencies in the current Optimizer mean that SQL Server is yet to be able to exploit properly all those extra CPUs. Adam’s contention was that the current optimizer uses essentially the same costing model for many of its core operations as it did back in the days of SQL Server 7, based on assumptions that are no longer valid. One example he gave was a "slow disk" bias that may have been valid back in 1997 but certainly is not on modern disk systems. Essentially, the optimizer assesses the relative cost of serial versus parallel plans based on the assumption that there is no IO cost benefit from parallelization, only CPU. It assumes that a single request will saturate the IO channel, and so a query would not run any faster if we parallelized IO because the disk system simply wouldn’t be able to handle the extra pressure. As such, the optimizer often decides that a serial plan is lower cost, often in cases where a parallel plan would improve performance dramatically. It was challenging and thought provoking stuff, as were his techniques for driving parallelism through query logic based on subsets of rows that define the "grain" of the query. I highly recommend you catch the session if you missed it. I’m interested to hear though, when and how often people feel the force of the optimizer’s shortcomings. Barring mistakes, such as stale statistics, how often do you feel the Optimizer fails to find the plan you think it should, and what are the most common causes? Is it fighting to induce it toward parallelism? Combating unexpected plans, arising from table partitioning? Something altogether more prosaic? Cheers, Tony.

  Read the article

• trying to setup wireless

  - by JohnMerlino

  I'm trying to set up wireless on vostro 1520 dell laptop, with latest Ubuntu install. Here's the output of some of the commands that I was told to run: lshw -C network viggy@ubuntu:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 03 serial: 00:24:e8:da:84:25 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.2.6 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:47 ioport:3000(size=256) memory:f6004000-f6004fff memory:f6000000-f6003fff memory:f6020000-f603ffff *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0e:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:fa000000-fa003fff *-network DISABLED description: Wireless interface physical id: 1 logical name: wlan0 serial: 0c:60:76:05:ee:74 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-29-generic firmware=N/A multicast=yes wireless=IEEE 802.11bg lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 1a:00.0 FireWire (IEEE 1394): O2 Micro, Inc. Device 10f7 (rev 01) 1a:00.1 SD Host controller: O2 Micro, Inc. Device 8120 (rev 01) 1a:00.2 Mass storage controller: O2 Micro, Inc. Device 8130 (rev 01) iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extensions. At this point in time, I don't have wireless.

  Read the article

• Need help partitioning when reinstalling Ubuntu 14.04

  - by Chris M.

  I upgraded to 14.04 about a month ago on my HP Mini netbook (about 16 GB hard disk). A few days ago the system crashed (I don't know why but I was using internet at the time). When I restarted the computer, Ubuntu would not load. Instead, I got a message from the BIOS saying Reboot and Select proper Boot device or Insert Boot Media in selected Boot device and press a key I took this to mean that I needed to reinstall 14.04. When I try to reinstall Ubuntu from the USB stick, I choose "Erase disk and install Ubuntu" but then I get a message: Some of the partitions you created are too small. Please make the following partitions at least this large: / 3.3 GB If you do not go back to the partitioner and increase the size of these partitions, the installation may fail. At first I hit Continue to see if it would install anyway, and it gave the message: The attempt to mount a file system with type ext4 in SCSI1 (0,0,0), partition # 1 (sda) at / failed. You may resume partitioning from the partitioning menu. The second time I hit Go Back, and it took me to the following partitioning table: Device Type Mount Point Format Size Used System /dev/sda /dev/sda1 ext4 (checked) 3228 MB Unknown /dev/sda5 swap (not checked) 1063 MB Unknown + - Change New Partition Table... Revert Device for boot loader installation: /dev/sda ATA JM Loader 001 (4.3 GB) At this point I'm not sure what to do. I've never partitioned my hard drive before and I don't want to screw things up. (I'm not particularly tech savvy.) Can you instruct me what I should do. (P.S. I'm afraid the table might not appear as I typed it in.) Results from fdisk: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 4294 MB, 4294967296 bytes 255 heads, 63 sectors/track, 522 cylinders, total 8388608 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda doesn't contain a valid partition table Disk /dev/sdb: 7860 MB, 7860125696 bytes 155 heads, 31 sectors/track, 3194 cylinders, total 15351808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009a565 Device Boot Start End Blocks Id System /dev/sdb1 * 2768 15351807 7674520 b W95 FAT32 ubuntu@ubuntu:~$ Here is what it displays when I open the Disks utility (I tried the screenshot terminal command you suggested but it didn't seem to do anything): 4.3 GB Hard Disk /dev/sda Model: JM Loader 001 (01000001) Size: 4.3 GB (4,294,967,296 bytes) Serial Number: 01234123412341234 Assessment: SMART is not supported Volumes Size: 4.3 GB (4,294,967,296 bytes) Device: /dev/sda Contents: Unknown (There is a button in the utility that when you click it gives the following options: Format... Create Disk Image... Restore Disk Image... Benchmark but SMART Data & Self-Tests... is dimmed out) When I hit F9 Change Boot Device Order, it shows the hard drive as: SATA:PM-JM Loader 001 When I hit F10 to get me into the BIOS Setup Utility, under Diagnostic it shows: Primary Hard Disk Self Test Not Support NetworkManager Tool State: disconnected Device: eth0 Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 00:26:55:B0:7F:0C Capabilities: Carrier Detect: yes Wired Properties Carrier: off When I run command lshw -C network, I get: WARNING: you should run this program as super-user. *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:16 memory:feafc000-feafffff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: c0 serial: 00:26:55:b0:7f:0c capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:febc0000-febfffff ioport:ec80(size=128) WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• Upgraded to 12.04 now wifi doesn't work

  - by Benito Kestelman

  My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

  Read the article

• Cannot get ATI Drivers installed

  - by bittoast67

  I am trying to install the Catalyst driver. The best I can get is a strange resolution problem and firefox acts all wonkt. The worst I have gotten is low graphics mode in which I just reinstall Ubuntu. I have a HP Pavilion Dv7 laptop. With Radeon 3200 HD. I plan to try again with a fresh install of Ubuntu 12.4.3 as I have heard its the most compatible. This is what I have done: I have tried just the easy way of going to synaptic and installing the drivers that way. the fglrx package (not the fglrx update). And if memory serves I think that boots me into low graphics mode. So, fresh install of Ubuntu and tried again. I have done everything a couple times from this site (http://wiki.cchtml.com/index.php/Ubuntu_Precise_Installation_Guide) following every instruction to a T. That gets me something, such as a lowered fan speed and a much cooler computer, but I also lose most of my resolution. And displays says its the best resolution I can get. I also have a very screwy firefox. Using this method I can see AMD Catalyst Control Center in my dash (two of them really one administrator and one not) but when I try to open it it says no amd driver detected. So again, ubuntu reinstall. I have tried the GUI method from the Legacy driver I got from AMD's site. It runs through smoothly and at the very end after I exit the installer it gives me an error. I have also tried various other methods using terminal, as well as various different drivers (the one from the amd's site and the one suggested in the above link for my graphics card) both to no avail. When I try the method in the link on number 2, and I get the super low res and screwy fire fox. I type in, fglrxinfo ,and get a badrequest error. I have yet to type in fglrxinfo and get anything like what I am supposed to. UPDATE: I am now currently reinstalling Ubuntu 12.4. I tried the above mentioned link - thank you very much!- just to see on the previously failed driver attempt by following the purge commands. And to no avail when typing fglrxinfo I still get the badrequest thing. I will update again after a try with a true fresh install. Thanks again!! UPDATE: Alright everyone. Still no go. I have done everything word per word in the provided tutorial. I have rebooted my computer again to a fucked up resolution and this is what I get when typing fglrxinfo: $ fglrxinfo X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 153 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 12 Current serial number in output stream: 12 I would like to add that when installing this file: fglrx_8.970-0ubuntu1_amd64.deb I got this: Building initial module for 3.8.0-29-generic Error! Bad return status for module build on kernel: 3.8.0-29-generic (x86_64) Consult /var/lib/dkms/fglrx/8.970/build/make.log for more information. update-initramfs: deferring update (trigger activated) Processing triggers for ureadahead ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-29-generic Processing triggers for libc-bin ... ldconfig deferred processing now taking place Any ideas? Anyone? I cant for the life of me figure out what I am doing wrong.

  Read the article

• "The connection has timed out" - Please help!

  - by gon

  I recently installed a fresh Ubuntu 12.04 LTS on a desktop, and the installation itself was successful (other than 'grub rescue' issue that I encountered but fixed) but this connection problem is really giving me a headache. Symptoms: 1. When I open the FireFox browser and try to connect to a website, it just hangs for a while saying "Connecting..." but eventually loads an error page "The connection has timed out". 2. It's not a browser problem (and I tried setting ipv6 thing to "true" at about:config) because running "sudo apt-get install [some-random-package]" at terminal fails ("E: Unable to locate package [package]") too. All other operations that need internet access are not working. 3. I certainly see a wired network (called "eth1") at the Network Manager, and it says "Connection Established" after disconnecting and then connecting again. I have tried almost everything that could be found from google search results still no luck. Their problems slightly differ from mine or the solutions just don't work. By the way it didn't have internet access when installing Ubuntu 12.04. (I ignored the message that I need internet to install Ubuntu) Could this be a problem? I'm sorry I don't remember if internet worked or not on the previous version of Ubuntu. :( I would really appreciate your help... I don't even know what more to do if this fails too.. Thanks!! Thanks for your comment. Here is the result of ifconfig: eth0 Link encap:Ethernet HWaddr 78:ac:c0:3d:b2:b9 inet addr:10.10.65.185 Bcast:10.10.65.255 Mask:255.255.255.0 inet6 addr: fe80::7aac:c0ff:fe3d:b2b9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3907 errors:0 dropped:0 overruns:0 frame:0 TX packets:771 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:393118 (393.1 KB) TX bytes:73472 (73.4 KB) Interrupt:16 eth1 Link encap:Ethernet HWaddr 78:ac:c0:3d:b2:b8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204 (204.0 B) TX bytes:204 (204.0 B) route -n: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.10.65.1 0.0.0.0 UG 0 0 0 eth0 10.10.65.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 /etc/resolv.conf: # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 8.8.8.8 nameserver 8.8.4.4 nameserver 10.81.1.8 nameserver 10.1.2.10 nameserver 127.0.0.1 search yamatake.local /etc/network/interfaces: auto lo iface lo inet loopback #auto eth0 #iface eth0 inet dhcp #auto eth1 #iface eth1 inet dhcp And I'll also include the result of 'sudo lshw -C network' in case it might help: *-network description: Ethernet interface product: NetXtreme BCM5764M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 78:ac:c0:3d:b2:b9 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5764m-v3.35 ip=10.10.65.185 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:93 memory:fc000000-fc00ffff *-network description: Ethernet interface product: NetXtreme BCM5764M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth1 version: 10 serial: 78:ac:c0:3d:b2:b8 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5764m-v3.35 latency=0 link=no multicast=yes port=twisted pair speed=100Mbit/s resources: irq:94 memory:fb000000-fb00ffff

  Read the article

• Cannot establish maximum resolution on ASUS PB278Q

  - by dentuzhik

  I've recently bought brand new ASUS PB278Q monitor. When trying to connect to my laptop, everything works great, except that I can't get the native resolution of my monitor (2560x1440) working. The automatic is 1920x1080. My graphic card is Nvidia GeForce 320m. Here's output from lspci for it: ~$ lspci | grep VGA 02:00.0 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 320M] (rev a2) and also xrandr: ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected primary 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 I have proprietary drivers installed on my machine, here's the info about the monitor from nvidia-settings (Actually I don't have enough reputation to post images, so here's the text): Chip Location: Internal Signal: TDMS Connection link: Single Native resolution: 2560x1440 Refresh rate: 60.00 Hz The monitor is connected to laptop via HDMI cable, and honestly I have no idea what version it is, and what version is my HDMI output of my graphics card. I tried to find how I can figure it out on the web, but had no luck. Also my video card has only VGA and HDMI outs so I can't test neither DVI-D cable nor DisplayPort. So apparently, there's some problem over there. At least I want to know exactly what's going on. I've tried to see if it a linux-specific problem, but windows also gave me the same resolution by default. What I've already tried: Connect through VGA (stupid one, of course it gave me 1920x1080). Checked two HDMI cables (not sure if they're the same or not, as mentioned above). Played around with xrandr and adding custom modes. Didn't help. Surfed for the info a lot on the web, but couldn't get appropriate results. Actually xrandr gives me the following: ~$ cvt 2560 1440 60 # 2560x1440 59.96 Hz (CVT 3.69M9) hsync: 89.52 kHz; pclk: 312.25 MHz Modeline "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr --newmode "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected primary 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 2560x1440_60.00 (0x34f) 312.2MHz h: width 2560 start 2752 end 3024 total 3488 skew 0 clock 89.5KHz v: height 1440 start 1443 end 1448 total 1493 clock 60.0Hz ~$ xrandr --addmode HDMI-0 2560x1440_60.00 X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 29 Current serial number in output stream: 30 What I intend to do next: Try another HDMI cable? Try HDMI to DVI-D cable? Try HDMI to DisplayPort cable? Another type of adapters? VGA to DVI-D? Buy another laptop with another graphic card. Damn. My ideas pretty much end here. Any ideas? Any explanations why it isn't working are appreciated.

  Read the article

• Handshake violation when trying to access one website

  - by Miguel

  I have a TZ 190 Wireless Enhanced with SonicOS Enhanced 4.2.1.0-20e. Yesterday, people could access without any problems a bank website wich uses HTTPS. Today, it is imposible to access only that website, every other ones works without problems. When checking the log message filtering to my IP only, this is what appears and I suspect is the cause of this problem, because all other websites are working: Priority: Notice Category: Network Access Message: TCP handshake violation detected; TCP connection dropped Source: X.Y.Z.3, 51997, LAN (admin) Destination: 200.14.232.18, 443, WAN Notes: Handshake Timeout Where X.Y.Z.3 is my local IP. I've tried to change TCP Settings under Firewall option, and activated this options with no success: Enforce strict TCP compliance with RFC 793 and RFC 1122 and Enable TCP checksum enforcement I've also tried to find the MTU and at first I got: Packet needs to be fragmented but DF set But when I lower the value of ping -f -l to 1468 I got: Request timeout. Also I deactivate CFS in lan and wan zones. Nothing works. Can you please help me? Any Ideas?

  Read the article

• DD-WRT: DNSMasq expand-hosts not working

  - by Craig Walker

  I have a Linksys router running DD-WRT (Firmware: DD-WRT v24-sp2 (09/08/09) mini). I have it successfully resolving the DNS names for my DHCP-assigned systems, but only when I fully-qualify those domains. This is despite using the "expand-hosts" DNSMasq additional option, which is supposed to activate this precise function. Here's my dnsmasq.conf: interface=br0 resolv-file=/tmp/resolv.dnsmasq domain=example.com dhcp-leasefile=/tmp/dnsmasq.leases dhcp-lease-max=51 dhcp-option=lan,3,10.77.0.5 dhcp-authoritative dhcp-range=lan,10.77.0.100,10.77.0.149,255.255.0.0,1440m dhcp-host=00:1A:A0:1D:82:5A,astatichostname,10.77.1.40,infinite expand-hosts (FYI: example.com and astatichostname are placeholders for the real-deal names I use. My network uses 10.77.0.0/16; my router is on 10.77.0.5.) Results: > nslookup astatichostname 10.77.0.5 Server: 10.77.0.5 Address: 10.77.0.5#53 ** server can't find astatichostname: NXDOMAIN > nslookup astatichostname.example.com 10.77.0.5 Server: 10.77.0.5 Address: 10.77.0.5#53 Name: astatichostname.example.com Address: 10.77.1.40 Is there something else that could be tripping up expand-host in DNSMasq?

  Read the article

• DrayTek 2820 configuration using public IP addresses

  - by Kev

  I have a /29 range of public IP addresses assigned to me by my ISP. I'm trying to configure a SIP VOIP handset to register with my VOIP provider who recommend using public IP addresses rather than NAT. I have a DrayTek 2820 router flashed with the latest firmware and have configured my router as per DrayTek's FAQ at: How do I use a public subnet on the LAN (non-NAT operation ) ? My IP range is: xx.xx.94.16 -> xx.xx.94.23 This gives a usable range of: xx.xx.94.17 -> xx.xx.94.22 My router's public IP address is: xx.xx.94.17, the SIP VOIP handset is allocated xx.xx.94.18. I have a second internet connection and via that I can ping the handset. However for some reason I can't seem to get it to register with the provider. I tried adding a new Firewall filter to pass through from WAN to LAN: Source: ANY, Destination: xx.xx.94.18, UDP - Ports 1024 -> 65535 Out of interest I also tried opening port 80 to see if I could browse to the phone's admin web interface but no joy. I know that my ISP aren't blocking inbound service ports because I NAT Port Forwarded port 80 to one of my internal web servers and it rendered a test page I had set up. All the NAT settings are reset to factory defaults, i.e. there are no Port Redirection, DMZ Host, Open Ports or Address Mappings configured. The handset I'm using is a GrandStream GXP-2000. Is there anything else I should be doing?

  Read the article

• IPCop Packet Mangling

  - by Zenham

  I've found myself in a pickle replacing an old firewall for a client this afternoon. I'm configuring their new IPCop firewall (1.4.21), Zerina OpenVPN addon is installed. What I need to do: There are three network interfaces, currently set up as red (WAN), green (LAN, 192.168.20.0/24) and orange (remote network 10.1.20.0/24). The orange interface is a direct fiber link to another organization. Simple description: Traffic and networks appear to be properly configured at this point, but I have many (150+) specific IPs on the LAN which, when accessing the resources on the 10.1.20.x network, need to be mangled to appear to be coming from the 10.1.20.0/24 network (and return traffic properly delivered). The routing on the far side was configured earlier and should be fine, but I need to redirect any packets coming across destined for those IPs to end up at their proper destination. The addressing is fixed and predictable (ie. 192.168.20.125 - 10.1.20.125). I need to insert whatever rules I have into the IPCop ruleset through /etc/rc.local I know, I'm just not sure about how I should structure this. There's CUSTOMOUTPUT and CUSTOMINPUT targets, both which currently just consist of the single rule redirecting packets to the OVPNOUTPUT/OVPNINPUT targets, so I'm guessing I should insert a rule matching outbound packets destined for the 10.1.20.x network and redirecting to a new target (maybe called TO-ORANGE) and a rule at the top of CUSTOMINPUT which redirects to a FROM-ORANGE target. Under those targets, I would have rules which do the IP matching and mangling. Am I approaching this right? If so, I'm not very familiar with mangle, and would appreciate seeing examples of how to write that source-IP rewrite. If not, how would you suggest doing this? TIA! edit: I notice additionally that the nat table has CUSTOMPREROUTING and CUSTOMPOSTROUTING targets, I guess I could alternatively post the rules in there....

  Read the article

• Windows Server 2008 DHCP with RRAS

  - by Guillermo Prandi

  I have a Windows Server 2008 R2 which is a member of a domain, but is placed in a remote location. The server is directly connected to Internet. Clients need to access a particular insecure TCP service in this server (ports 9730 and 9731). Since clients have dynamic IP addresses I cannot know in advance, I thought it would be nice to have them connected through a VPN in order to access the insecure service, but ONLY to access that service, like this: Client ------> VPN TUNNEL ------> (Insecure service at Server) | \----> (Normal internet access) I'd enable the insecure ports in the firewall only from VPN accesses. For this I configured RRAS in the server and gave it a static IP address range (172.19.1.2 through 172.19.1.254) to serve the clients. First I thought I could use DHCP to assign the addresses, but I cannot use DHCP in my LAN connection (not allowed by the hosting service). I tried configuring DHCP binding it to a Microsoft Loopback Adapter, but that's not supported as a DHCP source by RRAS. What I want to accomplish is to send specific DHCP options to the client (network mask, routing table, etc.). In particular: Prevent the client from having the server as default router (without changing the client's "use default gateway in remote network"). Have it as a route for the server's internal RRAS address only (172.19.1.1). Prevent the client from using a 255.255.0.0 mask for the 172.19.x.x network (a 255.255.255.0 mask would be better). Can I do that with RRAS only? How? Currently, the only solution I can think of is to use DHCP in the LAN adapter, but filter DHCP packets so they don't reach the provider's network. However, I'm not sure if that will work. Any suggestions are welcomed! Guille

  Read the article

• Centos IPTables configuration for external firewall

  - by user137974

  Current setup Centos which is a Web, Mail (Postfix,Dovecot), FTP Server and Gateway with public ip and private ip (for LAN Gateway). We are planning to implement external firewall box and bring the server to LAN Please guide on configuring IPTables... Unable to receive mail and outgoing mail stays in postfix queue and is sent after delaying... The local ip of the server is 192.168.1.220 iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP incoming HTTP iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 443 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 443 -m state --state ESTABLISHED -j ACCEPT outgoing HTTP iptables -A OUTPUT -o eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT FTP iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 21 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 1024:65535 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 1024:65535 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT SMTP iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 25 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 1024:65535 -d 0/0 --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --sport 25 -d 192.168.1.220 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT POP3 iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 110 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 110 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT

  Read the article

• Multiple public IPs through DD-WRT without 1-to-1 NAT

  - by Stephen Touset

  I've done a search here and wasn't able to find anything relevant to my situation. I apologize in advance if I've missed an existing post on the topic. Our ISP has provided us with 6 static IP addresses. We are currently using two of them (plus one for the Comcast-provided router). One of the static addresses routes to our internal network, and the other goes to our VOIP phone system. Unfortunately, the Comcast machine doesn't support QoS, so our VOIP calls have been choppy. We plan to put the Comcast-provided router into bridge mode and replace it with an ASUS RT-N16 running DD-WRT. However, I'm unsure how to set up DD-WRT to function similarly to our existing Comcast router. The Comcast router's WAN IP is the first of our static IP addresses. We did not need to provide an internal LAN IP address — simply connecting machines that use our other public addresses to the LAN ports on the Comcast router is enough for it to route between the connected machines and our internet connection. Is there a way to do a similar setup through the DD-WRT? Thanks in advance.

  Read the article

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

• How to set up IP forwarding on Nexenta (Solaris)?

  - by Gleb

  I am trying to set up IP forwarding on my Nexenta box: root@hdd:~# uname -a SunOS hdd 5.11 NexentaOS_134f i86pc i386 i86pc Solaris The box has 2 network interfaces: root@hdd:~# ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g1: flags=1001100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4,FIXEDMTU> mtu 1500 index 2 inet 192.168.12.2 netmask ffffff00 broadcast 192.168.12.255 ether 68:5:ca:9:51:b8 myri10ge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 9000 index 3 inet 10.10.10.10 netmask ffffff00 broadcast 10.10.10.255 ether 0:60:dd:47:87:2 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 192.168.12.0 is my normal LAN with 192.168.12.1 being the firewall/gateway 10.10.10.0 is a separate LAN for iSCSI (with no internet access) I want to set up IP forwarding so that a computer on 10.10.10.0 will be able to access the internet by using 10.10.10.10 as a gateway (I don't need any port forwarding) I have turned on IP forwarding: root@hdd:~# routeadm Configuration Current Current Option Configuration System State --------------------------------------------------------------- IPv4 routing disabled disabled IPv6 routing disabled disabled IPv4 forwarding enabled enabled IPv6 forwarding disabled disabled Routing services "route:default ripng:default" Routing daemons: STATE FMRI disabled svc:/network/routing/rdisc:default disabled svc:/network/routing/route:default disabled svc:/network/routing/legacy-routing:ipv4 disabled svc:/network/routing/legacy-routing:ipv6 disabled svc:/network/routing/ripng:default online svc:/network/routing/ndp:default But when I dry to start ipnat, I get an error: root@hdd:~# ipnat -CF -f /etc/ipf/ipnat.conf ioctl(SIOCGNATS): I/O error Here is the config: root@hdd:~# cat /etc/ipf/ipnat.conf #!/sbin/ipnat -f - # map e1000g1 10.10.10.10/24 -> 192.168.12.2/32 So the question is how to fix this.. Thanks in advance!

  Read the article

• Opening and Testing Ports on Modem > Router Connection

  - by JakeTheSnake

  Working off of my last question, I can access my server's FTP over the LAN but not over the internet. I'm using Filezilla on port 666. My router/modem configuration is as such (similar to other post): 1) Modem connects to WAN 2) WAN port on modem connects to LAN port on Router 3) Modem internal IP address is 192.168.0.254 4) Router internal IP address is 192.168.0.1 5) Modem has DHCP turned OFF 6) Router has DHCP turned ON 7) Router is running Tomato firmware and it's set as 'Router' (not 'Gateway') 8) The internet is working (just had to say that) I've set up port forwarding both on the modem and router - both route port 666 to the IP address of 192.168.0.3 (TCP); that is the IP address of the server which has FileZilla running. I don't know if that's hindering anything but I've also tried it with just the modem and just the router...same result. I've also tried setting the server to be DMZ (both on router and modem). Neither router nor modem have anything in their logs about denying inbound traffic on port 666 so my ability to troubleshoot stops there. I've tried contacting my ISP (Telus, running on mobility plan...it's a "Smart" Hub) but they weren't much help. They said they only block port 25 and 80 and maybe a few others, but not most ports. I test whether or not the port is open by going to canyouseeme.org - I don't know whether or not that would produce a 'connection refused' result just based on the fact that the FTP requires a login...I'm not well versed on this matter. FWIW, sometimes I get a 'connection refused' error on canyouseeme.org but mostly it's 'connection timed out'. I don't know what else to do at this point.

  Read the article

• DNS Server on Fedora 11

  - by Funky Si

  I recently upgraded my Fedora 10 server to Fedora 11 and am getting the following error in my DNS/named config. named[27685]: not insecure resolving 'fedoraproject.org/A/IN: 212.104.130.65#53 This only shows for certain addresses some are resolved fine and I can ping and browse to them fine, while others produce the error above. This is my named.conf file acl trusted-servers { 192.168.1.10; }; options { directory "/var/named"; forwarders {212.104.130.9 ; 212.104.130.65; }; forward only; allow-transfer { 127.0.0.1; }; # dnssec-enable yes; # dnssec-validation yes; # dnssec-lookaside . trust-anchor dlv.isc.org.; }; # Forward Zone for hughes.lan domain zone "funkygoth" IN { type master; file "funkygoth.zone"; allow-transfer { trusted-servers; }; }; # Reverse Zone for hughes.lan domain zone "1.168.192.in-addr.arpa" IN { type master; file "1.168.192.zone"; }; include "/etc/named.dnssec.keys"; include "/etc/pki/dnssec-keys/dlv/dlv.isc.org.conf"; include "/etc/pki/dnssec-keys//named.dnssec.keys"; include "/etc/pki/dnssec-keys//dlv/dlv.isc.org.conf"; Anyone know what I have set wrong here?

  Read the article

• Is there a reason to use internal DNS over 8.8.8.8 ?

  - by skylarking

  I've inherited a LAN where there is really no name resolution being done for local resources... i.e. all users enter IP addresses manually to access printers and network shares. There are no LDAP servers or domains either....workstations simply connect to the network without authentication. DHCP is handled via a core switch... And DNS settings are also handed out by this same core switch. Currently, the DNS assignments are as such, and in this order: 10.1.1.50 / old Pentium III Windows 2003 box running DNS service- 128 MB RAM 169.200.x.x / ISP 4.2.2.2. / the well known public one There a couple thousand clients on the LAN....and most of the activity is web browsing ( this is an educational setting ). First of all, the server seems woefully underpowered for this task...yet there is virtually no slowness when web surfing by clients.... How much horsepower should a heavily used DNS server have ? I have also heard using 4.2.2.2 is a bad idea .... since it has been so overused... Finally, wouldn't it make sense to have a robust external DNS server listed first? ( Google's 8.8.8.8 would seem to be a logical candidate )

  Read the article

• Issues with sustained traffic with PFSense

  - by Farseeker

  Last week we had to replace our PFSense firewall because it had a catastrophic hardware failure. All but one of the NICs were taken out of the old server and put into the new one. The one NIC that was not moved was the LAN NIC as this is on-board. The other NICs are all WAN connections and the must all be present (i.e. I can't disable one just for the sake of testing) After re-installing PFSense and restoring our backup of the configuration, everything came back online just fine, however on the new hardware any download that takes longer than about 10 seconds just times out in the middle. Example 1: Downloading from Microsoft.com goes at about 900k/sec and times out after about 10 seconds (thus, just under 10Mb of content) Example 2: Downloading from cnet.com goes at about 300k/sec and times out after about 10 seconds (thus, about 3Mb of content). By times out, I mean that the download just stops, and you have to pause/resume to get the next part done, repeat and rinse until the download is complete. However it's not consistant, sometimes it's 10 seconds, sometimes it's 4 seconds, and it sometimes you can't even load a heavy HTML page because the page never finishes. I assume this is most likely because PFSense does not like the onboard NIC, as this is the primary difference between the two servers. It's recognised as NFE0, and there's no room in the server for any more NICs and I don't have any dual-port NICs handy to experiment with a different LAN connection. I've never had to troubleshoot this sort of issue before. Can anyone give me some pointers about where to start? Linux is not my forte so please be kind!

  Read the article

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >