Search Results

Search found 21500 results on 860 pages for 'ajax request'.

Page 740/860 | < Previous Page | 736 737 738 739 740 741 742 743 744 745 746 747  | Next Page >

• Delayed internet access

  - by Joel Coel

  When I (and presumably my users) first start up or log in to my computer I can't get internet access until several minutes after logging in. Internet pages like serverfault.com will time out. During this time I can access internal web servers. Sometimes pinging the gateway seems to fix the problem. I'm using Windows 7 on this machine with wifi, and the problem seems limited to the wifi network, which is on a separate vlan. The wired network does not share the problem, but I know it's not the wifi connection itself because the internal sites work. The wifi access point is attached to a 3Com 4200 switch, with the port set for vlan 2 untagged, vlan 1 tagged. The 4200 has a fiber connection to a 3Com 4900SX fiber switch that acts almost as a router here. The fiber connection is vlan 1 untagged vlan 2 tagged at both ends. The gateway is then attached to a different 4200 (vlan 1 untagged, vlan 2 tagged) that has a similar fiber connection to the 4900SX. vlan 2 has 192.168.8.0/22 IPs, vlan 1 has 10.1.0.0/16 IPs. The 4900SX has an interface for both vlans (10.1.1.1/192.168.8.1), as does the gateway (10.1.1.5/192.168.8.5). There is one dchp server for both vlans on the same switch as the gateway. It chooses a dhcp scope based on the interface used by the 4900sx to forward the dhcp request. There is also a network access list on the 4900sx set to deny all vlan2 traffic to any 10.1.x.x host, with exceptions made for a few servers, including dhcp, 4900sx, and the gateway. I think that about covers it. Any ideas on why internet access would be delayed like this?

  Read the article

• Optimizing Apache for large file serving

  - by D_Guy13

  I have a random problem with Apache that I can't quite figure out, here is my setup, Windows Server 2008 R2, 64 Bit, 5GB RAM, SSD with 200 MB(Read/write) and Dual Core CPU @ 2.1 GHz A dump from mod-staus, Server Version: Apache/2.4.7 (Win32) mod_limitipconn/0.24 mod_antiloris/0.5.2 PHP/5.5.9 Server MPM: WinNT Apache Lounge VC11 Server Built: Nov 21 2013 20:13:01 Current Time: Thursday, 21-Aug-2014 23:38:06 W. Europe Daylight Time Restart Time: Thursday, 21-Aug-2014 20:30:47 W. Europe Daylight Time Parent Server Config. Generation: 1 Parent Server MPM Generation: 1 Server uptime: 3 hours 7 minutes 18 seconds Server load: -1.00 -1.00 -1.00 Total accesses: 283025 - Total Traffic: 1172.2 GB 25.2 requests/sec - 106.8 MB/second - 4.2 MB/request 62 requests currently being processed, 388 idle workers Serving large .zip & iso files using mod_xsendfile. (File size range 500 MB - 1.5 GB) The setup works and is running fine. CPU usage is very unstable, jumps all the time between 10% - 90% and the servers goes down when it hits 100%. In that case I have to hard restart the server. Server it outputting traffic at 30 Mbps. Is there anything else I should think about to get a more stable CPU usage? Is that CPU usage normal? Can switching to Linux help me achieve better CPU usage?

  Read the article

• Users getting 'flooded' with not read notifications (NRNs) for old emails and meeting requests

  - by Exile

  I'm being placed under quite a lot of pressure from senior management over a relatively trivial issue. Basically the vast majority of users are complaining that they receive not read notifications (NRNs) for old emails and meeting requests in large numbers multiple times a day. I know something strange is happening because some are delivered at silly times in the morning (i.e 3AM or 4AM). The problem I have is that these some of these NRNs are from meeting requests and messages that are 120 days old, so some users have deleted the original message so I don’t actually know if the NRN is from an email or meeting request. This is typical of what users receive as a NRN: From: Sender Sent: 23 March 2012 04:16 To: Recepient Subject: Not read: Accepted: Status update Your message To: Sender Subject: Accepted: Status update Sent: Wednesday, November 23, 2011 8:59:00 AM (UTC) Dublin, Edinburgh, Lisbon, London was deleted without being read on Friday, March 23, 2012 4:15:32 AM (UTC) Dublin, Edinburgh, Lisbon, London. ... From: Sender Sent: 18 March 2012 01:13 To: Recepient Subject: Not read: Gold delivery - Sourcing module Your message To: Sender Subject: Gold delivery - Sourcing module Sent: Friday, November 18, 2011 9:37:58 AM (UTC) Dublin, Edinburgh, Lisbon, London was deleted without being read on Sunday, March 18, 2012 1:12:37 AM (UTC) Dublin, Edinburgh, Lisbon, London. I have done a search and found the following: http://support.microsoft.com/kb/2544246 http://support.microsoft.com/kb/2471964 But we already installed 'Update Rollup 6 for Exchange Server 2010 Service Pack 1' back in December, so I am not sure what we can do to fix this?

  Read the article

• nginx codeigniter rewrite: Controller name conflicts with directory

  - by palerdot

  I'm trying out nginx and porting my existing apache configuration to nginx. I have managed to reroute the codeigniter url's successfully, but I'm having a problem with one particular controller whose name coincides with a directory in site root. I managed to make my codeigniter url's work as it did in Apache except that, I have a particular url say http://localhost/hello which coincides with a hello directory in site root. Apache had no problem with this. But nginx routes to this directory instead of the controller. My reroute structure is as follows http://host_name/incoming_url => http://host_name/index.php/incoming_url All the codeigniter files are in site root. My nginx configuration (relevant parts) location / { # First attempt to serve request as file, then # as directory, then fall back to index.html index index.php index.html index.htm; try_files $uri $uri/ /index.php/$request_uri; #apache rewrite rule conversion if (!-e $request_filename){ rewrite ^(.*)/?$ /index.php?/$1 last; } # Uncomment to enable naxsi on this location # include /etc/nginx/naxsi.rules } location ~ \.php.*$ { fastcgi_split_path_info ^(.+\.php)(/.+)$; # NOTE: You should have "cgi.fix_pathinfo = 0;" in php.ini # With php5-cgi alone: fastcgi_pass 127.0.0.1:9000; # With php5-fpm: #fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } I'm new to nginx and I need help in figuring out this directory conflict with the Controller name. I figured this configuration from various sources in the web, and any better way of writing my configuration is greatly appreciated.

  Read the article

• Thunderbird 11.0.1 and Lightning 1.3: How do I propose a different time for a meeting?

  - by seaao

  This all happens on my x64 Linux workstation btw. tl;dr: My colleague invited some people and me for a meeting. The meeting was scheduled a week to late. I -wrongfully- accepted. How do I propose a new time? To explain a bit more in detail: I received a meeting request in my mailbox. Thunderbird is so nice to let me accept or reject it, and after I click the button to accept, it is directly added to my calendar. But when I double click on the meeting to edit it, I get a function-wise scaled-down version of the meeting: The only settings I can alter are whether I want reminders, and if I go at all. Trying to drag it to another day doesn't work either: My calendar behaves like read-only (which it isn't btw). There are several questions (without answer...) to be found on Stack Overflow and on the Thunderbird knowledge base about using lightning. But I get the idea that I'm one of the few who won't comply with the team even before the meeting is started. My googling revealed no bugs or feature requests in the direction I'm thinking. A link to an explanation how to achieve this, or another perspective about how to reach the desired goal (meeting with my colleagues and me) would be mostly welcome!

  Read the article

• DNS lookup fails when with all the MAC workstations

  - by user39564

  Hi, I am having this insane problem. We are mac-heavy users. Around 10 workstations, one Xserve server, two windows workstation and one Linux (me). Last year I added an A record to our domain's DNS. However we had to change that a few months ago to a new IP. But all the Mac workstations fail to resolve the proper DNS and they still resolve to the old IP, even after 2 months. On both the windows workstation and my linux box a simple nslookup resolves to proper IP. However, on ALL the mac workstation, dig and nslookup report the old IP address. From my linux workstation: jp@lo:~$ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 68.71.40.xx But when I am trying the exact same command from any Mac workstation, I get the old IP: $ nslookup - 208.67.222.222 client.xyz.com Server: 208.67.222.222 Address: 208.67.222.222#53 Non-authoritative answer: Name: client.xyz.com Address: 98.143.155.xx The strange thing is that this only happens in our internal network. No problem from home nor from another server. I did try to flush the DNS, don't worry. It did not help. I am starting to wonder if my router (OpenWRT) or Mac OS X Server is not in some way spoofing the DNS request and thus acting as a cache. Any suggestions/comments would be grateful. Thank you, JP

  Read the article

• iis not listening on port 80

  - by Holian

  Hello, We have server 2003 and ISA 2004 with IIS 6 on same machnie. Everything worked well till yesterday, when we try to make some new rule in ISA..but this is a long story... Unfortunatelly something happend with our intranet site. Our site is on the port 80, but if we try to open on this client machines then we got and error page (which error page is our provider): 403-forbidden; Remote host not listening, the remote host is not prepared to acceppt the connection request. On the server i can open the site with port 80. If i change the port number in the iis and try to open the site with the port, then works well. I try to shut down IIS and start apache with a simple page. On the server works well but in clients the problem is the same, so i think this is not an IIS related problem. In the ISA we have a web pub rule, with port 80, no auth. Im pulling out my hair, please help.

  Read the article

• Conditionally set an Apache environment variable

  - by Tom McCarthy

  I would like to conditionally set the value of an Apache2 environment variable and assign a default value if one of the conditions is not met. This example if a simplification of what I'm trying to do but, in effect, if the subdomain portion of the host name is hr, finance or marketing I want to set an environment var named REQUEST_TYPE to 2, 3 or 4 respectively. Otherwise it should be 1. I tried the following configuration in httpd.conf: <VirtualHost *:80> ServerName foo.com ServerAlias *.foo.com DocumentRoot /var/www/html SetEnv REQUEST_TYPE 1 SetEnvIfNoCase Host ^hr\. REQUEST_TYPE=2 SetEnvIfNoCase Host ^finance\. REQUEST_TYPE=3 SetEnvIfNoCase Host ^marketing\. REQUEST_TYPE=4 </VirtualHost> However, the variable is always assigned a value of 1. The only way I have so far been able get it to work is to replace: SetEnv REQUEST_TYPE 1 with a regular expression containing a negative lookahead: SetEnvIfNoCase Host ^(?!hr.|finance.|marketing.) REQUEST_TYPE=1 Is there a better way to assign the default value of 1? As I add more subdomain conditions the regular expression could get ugly. Also, if I want to allow another request attribute to affect the REQUEST_TYPE (e.g. if Remote_Addr = 192.168.1.[100-150] then REQUEST_TYPE = 5) then my current method of assigning a default value (i.e. using the regular expression with a negative lookahead) probaby won't work.

  Read the article

• Running .NET code in XML file [closed]

  - by Stuart McIntosh

  We have 2 servers, 1 already configured with .net which works fine and a new one which appears to be configured the same but when I open an xml page in Internet Explorer it complains about the <% tag. We have IIS on win srvr 2003 SP2. The website is configured with .NET 1.1.4322. In ISAPI extensions have set the .XML extension to use c:\windows\microsoft.net\framework\v1.1.4322\aspnet_isapi.dll But the page: <property name="documentmaxage" value="0"/> <property name="documentmaxstale" value="0"/> <var name="m_Prompt_Path" /> <form id="InitVoiceXmlDoc"> <block> <assign name="m_Prompt_Path" expr="&quot;<% Response.Write(Request.QueryString["m_Prompt_Path"]); %>&quot;"/> </block> </form> gives the error: The XML page cannot be displayed Cannot view XML input using XSL style sheet. Please correct the error and then click the Refresh button, or try again later. The character '<' cannot be used in an attribute value. Error processing resource 'http://localhost:11119/fails.xml'. Lin... &quo... We have the same config on another server which works fine. So are there other options apart from the ISAPI extensions that I need to look at

  Read the article

• The Story of secure user-authentication in squid

  - by Isaac

  once upon a time, there was a beautiful warm virtual-jungle in south america, and a squid server lived there. here is an perceptual image of the network: <the Internet> | | A | B Users <---------> [squid-Server] <---> [LDAP-Server] When the Users request access to the Internet, squid ask their name and passport, authenticate them by LDAP and if ldap approved them, then he granted them. Everyone was happy until some sniffers stole passport in path between users and squid [path A]. This disaster happened because squid used Basic-Authentication method. The people of jungle gathered to solve the problem. Some bunnies offered using NTLM of method. Snakes prefered Digest-Authentication while Kerberos recommended by trees. After all, many solution offered by people of jungle and all was confused! The Lion decided to end the situation. He shouted the rules for solutions: Shall the solution be secure! Shall the solution work for most of browsers and softwares (e.g. download softwares) Shall the solution be simple and do not need other huge subsystem (like Samba server) Shall not the method depend on special domain. (e.g. Active Directory) Then, a very resonable-comprehensive-clever solution offered by a monkey, making him the new king of the jungle! can you guess what was the solution? Tip: The path between squid and LDAP is protected by the lion, so the solution have not to secure it. Note: sorry if the story is boring and messy, but most of it is real! =) /~\/~\/~\ /\~/~\/~\/~\/~\ ((/~\/~\/~\/~\/~\)) (/~\/~\/~\/~\/~\/~\/~\) (//// ~ ~ \\\\) (\\\\( (0) (0) )////) (\\\\( __\-/__ )////) (\\\( /-\ )///) (\\\( (""""") )///) (\\\( \^^^/ )///) (\\\( )///) (\/~\/~\/~\/) ** (\/~\/~\/) *####* | | **** /| | | |\ \\ _/ | | | | \_ _________// Thanks! (,,)(,,)_(,,)(,,)--------'

  Read the article

• certutil -ping fails with 30 seconds timeout - what to do?

  - by mark

  Dear ladies and sirs. The certificate store on my Win7 box is constantly hanging. Observe: C:\1.cmd C:\certutil -? | findstr /i ping -ping -- Ping Active Directory Certificate Services Request interface -pingadmin -- Ping Active Directory Certificate Services Admin interface C:\set PROMPT=$P($t)$G C:\(13:04:28.57)certutil -ping CertUtil: -ping command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. C:\(13:04:58.68)certutil -pingadmin CertUtil: -pingadmin command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. C:\(13:05:28.79)set PROMPT=$P$G C:\ Explanations: The first command shows you that there are –ping and –pingadmin parameters to certutil Trying any ping parameter fails with 30 seconds timeout (the current time is seen in the prompt) This is a serious problem. It screws all the secure communication in my app. If anyone knows how this can be fixed - please share. Thanks. P.S. 1.cmd is simply a batch of these commands: certutil -? | findstr /i ping set PROMPT=$P($t)$G certutil -ping certutil -pingadmin set PROMPT=$P$G

  Read the article

• ApplicationPoolIdentity IIS 7.5 to SQL Server 2008 R2 not working.

  - by Jack

  I have a small ASP.NET test script that opens a connection to a SQL Server database on another machine in the domain. It isn't working in all cases. Setup: IIS 7.5 under W2K8R2 trying to connect to a remote SQL Server 2008 R2 instance. All machines are in the same domain. Using the ApplicationPoolIdentity for the web site it fails to connect to the SQL Server with the following: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Data.SqlClient.SqlException: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. However if I switch the Process Model Identity to NETWORK SERVICE or my domain account the database connection is successful. I've granted the \$ access in SQL Server. I am not doing any sort of authentication on the web site, it is just a simple script to open a connection to a database to make sure it works. I have Anonymous Authentication enabled and set to use the Application pool identity. How do I make this work? Why is the ApplicationPoolIdentity trying to use ANONYMOUS LOGON? Better yet, how do I make it stop using the Anonymous logon?

  Read the article

• Apache2.2 not responding or logging anything on Win 7

  - by Adam

  I'm having some trouble with Apache2.2 on Windows 7. For over a year it's been running no problem, but all of a sudden requests have just stopped responding. They don't time out as such, the browser just keeps on waiting forever. Nothing is recorded in either the error log (set to debug level), the access log, or Windows' Event Log. The problem showed up when I added a new VHost and restarted, however a syntax check has shown there's no problem with the config (from the little I changed), and the service does actually start error free. I've also disabled VHosts and tried with just localhost. I've tried to telnet to the web server, and it connects, but nothing happens. The prompt just goes blank and I can't type anything, and effectively become stuck. I've ensured there's a rule within Windows Firewall for Apache, and I've even disabled the entire thing just to check it wasn't the cause. Still the same. If I stop Apache however, the request fails immediately. I've uninstalled and reinstalled Apache, in the hope it might magically fix something using the default config, but still no joy. I've tried using a different port but nothing different. Does anybody have any suggestions to fix this? Or to perhaps try and figure out either if it's Apache itself not responding or something sitting between the two that's holding things up? I'm not too savvy on debugging Windows issues like this and I've been searching for hours but not found anything of use to me. Cheers Adam

  Read the article

• Routing for remote gateway over VPN in Vista/7 broken?

  - by Raymond

  Hi, Situation is as follows. Home computer running Windows 7, sets up VPN connection (LT2P + IPSec, "use remote gateway" disabled) to office. Subnet is 192.168.64.x Office has Draytek Vigor 2920 router, subnet is 192.168.32.x What happens? - VPN connection itself works fine - Can ping any machine on the remote network - When trying to open a webpage from a host in the remote network, the remote server logs the incoming request, but the browser hangs on "waiting for..." and eventually times out. I have observed this problem on Windows Vista and Windows 7. On Windows XP however there is no problem like described above. The only clue I have is that there is a difference in the routing between XP and Vista/7. The output of "route print" on Windows XP looks like this: (See www.latunyi.com/routing_xp.png) So here the gateway for the 192.168.32.x subnet is the IP address that the local computer has in the remote network. The output of "route print" on Windows 7 (and Windows Vista) looks like this: (See www.latunyi.com/routing_win7.png") Now the gateway for the 192.168.32.x subnet is the IP address of the VPN router (32.1). I don't know if that causes this trouble, but it seems a bit strange. Enabling "use default gateway on remote network" doesn't make a difference. Using the new option "Disable class based route addition" in Windows 7 only makes the route to the VPN router disappear. I am really puzzled here. I assume the VPN routing can't be broken in both Vista and Windows 7, and this should just work without manually adding routes. I hope someone has a solution for this problem :-). Thanks!

  Read the article

• Windows 7 using llt for ipv6

  - by Seoman

  The question asked below is based on the specific implementations of the Os not the RFC. Looking on a way to be able to assign a fixed ip address to a host, before it boots I found that Centos 6 works fine with no modifications and Windows 7 does not work at all. As defined in enter link description here exists 3 valid ways of generate a DUID: 1 Link-layer address plus time 2 Vendor-assigned unique ID based on Enterprise Number 3 Link-layer address Looking at the centos, that works fine, I can see the following autogenerated DUID: option dhcp6.client-id 0:1:0:1:19:60:25:f1:52:54:0:6b:b9:9e; and the MAC address for this host is: ifconfig eth1 | grep HWaddr eth1 Link encap:Ethernet HWaddr 52:54:00:6B:B9:9E As you can see, the DUID containts the MAC address. I can assign a fixed ip address to this host by including an entry on my dhcp server similar to: host vm { hardware ethernet 52:54:00:6B:B9:9E; fixed-address6 2001:db8:0:1::200; if packet(0,1) = 1 { log(debug,"VM Request match!"); } } And the Centos 6 gets his ip. On the windows side, I faced a common problem explained on this other link enter link description here As summary, Win7 uses the option 2 of the DUID generation or a variation of this one. On the link explains how to move it to a llt (link layer + time) but is not working fine. If I modify the DUID to one that looks like the one generated on Centos (but with the right MAC) it works as expected. Question 1 How Can I change the DUID generation for Windows 7 to be based on MAC as Centos 6 does? Thanks

  Read the article

• How can I ensure that my static ip address is read from /etc/network/interfaces rather than dhcp?

  - by jonderry

  This is a follow up to the following question. I'm trying to set a static IP by changing /etc/network/interfaces to the following: # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.2.133 netmask 255.255.255.0 gateway 192.168.2.1 dns-nameservers 8.8.8.8 and then running /sbin/ifdown eth0; /sbin/ifup eth0. However, the change in IP address doesn't appear to take effect without editing /etc/dhcp/dhclient.conf and commenting out the following before running ifdown; ifup: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, dhcp6.name-servers, dhcp6.domain-search, netbios-name-servers, netbios-scope, interface-mtu, rfc3442-classless-static-routes, ntp-servers, dhcp6.fqdn, dhcp6.sntp-servers; Strangely, after commenting out this line, running ifdown; ifup works, but when I uncomment it, the behavior does not revert to the previous behavior of ignoring changes to my settings in /etc/network/interfaces (this doesn't seem like a problem, but I really need to be able to repeat this problem so that I can be confident that my solution is robust) Also, I'd rather not have to edit /etc/dhcp/dhclient.conf to change my static IP since it seems I should be able to do this by only editing interfaces. Can anyone explain the issues I'm seeing above and suggest the best way of making changes to static IP addresses take effect that admits reproducibility so that I can be sure that my approach works?

  Read the article

• VMware guest pauses when the host is idle - how do I keep it running?

  - by EMP

  I'm running VMWare Worstation 7 with Windows 7 x64 as guest, Windows XP x64 as host. Inside the guest I run a long-running console application, which prints out progress messages with timestamps on them. Sometimes I leave it running for several hours while I lock the host OS and don't touch the computer at all. When I come back I find that some time after I left it seems to have paused and automatically resumed: the console app hasn't made much progress and there's a large time gap in its progress messages. There's nothing relevant in the host event log, but in the guest Application event log I can see these messages around the time I left: A request to disable the Desktop Window Manager was made by process (VMware Tools Service) The Desktop Window Manager was unable to start because composition was disabled by a running application And later, around the time I returned, this shows up in the System log: The system time has changed to ?2012?-?01?-?12T06:36:46.921000000Z from ?2012?-?01?-?12T03:18:19.953079000Z. That seems to support my theory that it's VMware doing something and not Windows itself. The question is: how do I stop it doing that? I want my application to continue running. By the way, the power options are set to never sleep in both guest and host.

  Read the article

• Nginx Multiple If Statements Cause Memory Usage to Jump

  - by Justin Kulesza

  We need to block a large number of requests by IP address with nginx. The requests are proxied by a CDN, and so we cannot block with the actual client IP address (it would be the IP address of the CDN, not the actual client). So, we have $http_x_forwarded_for which contains the IP which we need to block for a given request. Similarly, we cannot use IP tables, as blocking the IP address of the proxied client will have no effect. We need to use nginx to block the requested based on the value of $http_x_forwarded_for. Initially, we tried multiple, simple if statements: http://pastie.org/5110910 However, this caused our nginx memory usage to jump considerably. We went from somewhere around a 40MB resident size to over a 200MB resident size. If we changed things up, and created one large regex that matched the necessary IP addresses, memory usage was fairly normal: http://pastie.org/5110923 Keep in mind that we're trying to block many more than 3 or 4 IP addresses... more like 50 to 100, which may be included in several (20+) nginx server configuration blocks. Thoughts? Suggestions? I'm interested both in why memory usage would spike so greatly using multiple if blocks, and also if there are any better ways to achieve our goal.

  Read the article

• sysbench memory test on ec2 small instance

  - by caribio

  I'm seeing a problem with sysbench memory test (the default version that's compiled in). This is on Ubuntu Maverick, sysbench installed via apt-get install sysbench. Running the same thing on Ubuntu @ Rackspace worked just as expected. While the CPU and I/O tests worked fine on EC2 servers, the memory test just runs without doing anything (notice the 0M in the test results). The instance used was the publicly available 'stock' Ubuntu image with no changes to it: ./ec2-run-instances ami-ccf405a5 --instance-type m1.small --region us-east-1 --key mykey Supplying more arguments (such as: --memory-block-size=1K --memory-total-size=102400M) didn't help. What am I doing wrong? Thanks. sysbench --num-threads=4 --test=memory run sysbench 0.4.12: multi-threaded system evaluation benchmark Running the test with following options: Number of threads: 4 Doing memory operations speed test Memory block size: 1K Memory transfer size: 0M Memory operations type: write Memory scope type: global Threads started! Done. Operations performed: 0 ( 0.00 ops/sec) 0.00 MB transferred (0.00 MB/sec) Test execution summary: total time: 0.0003s total number of events: 0 total time taken by event execution: 0.0000 per-request statistics: min: 18446744073709.55ms avg: 0.00ms max: 0.00ms Threads fairness: events (avg/stddev): 0.0000/0.00 execution time (avg/stddev): 0.0000/0.00

  Read the article

• Can mod-rewrite be used to set environmental variables?

  - by VLostBoy

  Hi, I've got an existing simple rewrite rule like so: <Directory /path> RewriteEngine on RewriteBase / # if the requested resource does not exist RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d # route the uri to a front controller RewriteRule ^(.*)$ index.php/$1 [L] </Directory> This works fine, but I want to do one of either two things. On the basis of detecting the clients accept-language header, I want to either (i) Set the detected language as an environmental variable that the script can use or (ii)Rewrite the request so that the url begins with the language code (e.g. www.example.com/en/some/resource) In terms of implementing (i), I defined this rule: <Directory /path> RewriteEngine on RewriteBase / # if the requested resource does not exist RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d # if the users preferred language is supported... RewriteCond %{HTTP:Accept-Language} ^.*(de|es|fr|it|ja|ru|en).*$ [NC] # define an environmental variable PREFER_LANG RewriteRule ^(.*)$ - [env=PREFER_LANG:%1] # route the uri to a front controller RewriteRule ^(.*)$ index.php/$1 [L] </Directory> I've tried a few variations, but PREFER_LANG is not defined in $_SERVER nor retrievable by getenv. In terms of implementing (ii)... lets just say its messy. I'll post it if I can't get an answer to one. Can anyone advise me? Thanks!

  Read the article

• 100% CPU when doing 4 or more concurrent requests with Magento

  - by pancake

  Currently I'm having trouble with a server running Magento, it's unbelievably slow. It's a VPS with a few Magento installations on it used for development, so I'm the only one using them. When I do 4 request all 2 seconds after each other I'm finished in 10 seconds. Slow, but still within the limits of my patience. When I do 4 "concurrent" requests, however (opening 4 tabs in a row, very quickly) all four cores go to 100% and stay there for like a minute. How is this possible? I know that there are a lot of possibilities here, so any tips on how to make an Apache/PHP server go faster are also welcome. It used to go a lot faster before, and I've also tried APC, but it kept causing problems (PHP errors, something with memory pools) so I've disabled it. By the way, the Magento cache is off and compiling is also off. I know this makes Magento slower than usual, but I don't think a 60 second response time is normal for any Magento installation. Virtual hardware: 4 Cores and 4096MB RAM Swap is never used (checked with htop) 100GB disk space, of which 10% is in use Software: Debian 6 DirectAdmin and apache custombuild PHP 5.2.17 (CLI) If you need more info, please tell me how to get it, because I probably don't know how. I do know how to use the command line in linux and the usage of quite a few commands, but my experience with managing a server is limited.

  Read the article

• Apache displays error page half way through PHP page execution

  - by Shep

  I've just installed Zend Server Community Edition on a Windows Server 2003 box, however there's a bit of a problem with the display of a lot of our PHP pages. The code has previously running under the same version of PHP (5.3) on IIS without any issues. By the looks of things, Apache (installed as part of Zend Server) is erroring out during the rendering of the page when it comes across something it doesn't like in the PHP. Going through the code, I've been able to get past some of the problems by removing the error suppression operator (@) from function calls and by changing the format of some includes. However, I can't do this for the whole site! Weirdly, the error code is reported as "200 OK". The code snippet below shows how the Apache error HTML interrupts the regular HTML of the page. <p>Ma quande lingues coalesce, li grammatica del resultant lingue es plu simplic e regulari quam ti del coalescent lingues.</<!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>200 OK</title> </head><body> <h1>OK</h1> <p>The server encountered an internal error or misconfiguration and was unable to complete your request.</p> <p>Please contact the server administrator, [email protected] and inform them of the time the error occurred, and anything you might have done that may have caused the error.</p> <p>More information about this error may be available in the server error log The Apache error log doesn't offer any explanation for this, and I've exhausted my Googling skills, so any help would be greatly appreciated. Thanks.

  Read the article

• Would a PHP application benefit from being served from a RAM drive?

  - by Tom Marthenal

  I am in charge of hosting a PHP application that is large and slow, but easy to scale. The application is entirely static, with writable disk storage needed. We've profiled the application, and the main bottleneck appears to come from loading the application and not the work the application does. The application is not CPU-intensive, although it does use a fair amount of memory (think Magento). Currently we distribute it by having a series of servers with the same PHP files on their hard drive and a load balancer in front of them. Easy but expensive. I've been reading about RAM disks and the IO benefits they offer, and was wondering if they would be well-suited to PHP applications. Since PHP applications are loaded from disk for every request and often involve lots of different files (as opposed to being kept in memory like with a Java application), I would figure that disk performance can be a severe bottleneck. Would placing the PHP files on a RAM disk and using the mount point as Apache's document root offer performance benefits? A startup script could create the RAM drive and then copy the files (which are plain-text and small) from a permanent location to the temporary RAM drive. Does this make sense, or should I just trust the linux kernel to cache the appropriate files in memory by itself?

  Read the article

• How do I troubleshoot nginx not recognizing passenger?

  - by Jade

  Issue: nginx does not seem to recognize my rails application Symptoms: When the server starts up, it shows the "Welcome to nginx!" message instead of my Rails application. Nginx seems to be using the local nginx path instead of the Rails root I specified: 2010/04/18 06:29:06 [error] 783#0: *1 "/usr/local/nginx/html/blog/index.html" is not found (2: No such file or directory), client: 1.2.3.4, server: www.farmerjade.com, request: "GET /blog/ HTTP/1.1", host: "www.farmerjade.com" I used [RVM and Passenger Setup on NGINX][1] to install nginx and passenger on a virtual machine. Here is my nginx configuration: user farmerjade; worker_processes 1; ... http { include mime.types; default_type application/octet-stream; passenger_ruby /home/farmerjade/.rvm/bin/passenger_ruby; passenger_root /home/farmerjade/.rvm/gems/ree-1.8.7-head/gems/passenger-2.2.11; ... server { listen 80; server_name www.farmerjade.com; root /home/farmerjade/farmerjade/public; passenger_enabled on; rails_env development; ... I'd appreciate any help anyone has to offer -- I'm quite new to nginx.

  Read the article

• Cannot make bind9 forward DNS query to subdomain unless recursive enabled

  - by PP.

  I am trying to develop my own dynamic DNS. I'm running my own custom DNS for the subdomain on port 5353. ASCII diagram: INET --->:53 Bind 9 --->:5353 node.js | V zone_files I have example.com. The node.js DNS is for dyn.example.com. In my /etc/bind/named.conf.local I have: zone "example.com" { type master; file "/etc/bind/db.com.example"; allow-transfer { zonetxfrsafe; }; }; zone "dyn.example.com" IN { # DYNAMIC type forward; forwarders { 127.0.0.1 port 5353; }; forward only; }; I've even gone so far as to add a NS in my example.com zone file: $TTL 86400 @ IN SOA ns.example.com. hostmaster.example.com. ( 2013070104 ; Serial 7200 ; Refresh 1200 ; Retry 2419200 ; Expire 86400 ) ; Negative Cache TTL ; NS ns ; inet of our nameserver ns A 1.2.3.4 ; NS record for subdomain dyn NS ns When I attempt to get a record from the subdomain server it doesn't get forwarded: dig @127.0.0.1 test.dyn.example.com However if I turn recursive on in /etc/bind/named.conf.options: options { recursion yes; } .. then I CAN see the request going to the subdomain server. But I don't want recursion yes; in my Bind configuration as it is poor security practice (and allows all-and-sundry requests that are not related to my managed zones). How does one forward (proxy) zone queries for just one zone? Or do I give up on Bind altogether and find a DNS server that can actually forward specific queries?

  Read the article

< Previous Page | 736 737 738 739 740 741 742 743 744 745 746 747  | Next Page >