Search Results

Search found 22277 results on 892 pages for 'multiple addresses'.

Page 740/892 | < Previous Page | 736 737 738 739 740 741 742 743 744 745 746 747  | Next Page >

• Many different BSOD

  - by Exa

  I'm experiencing multiple bluescreens for a couple of months now. Their error code is as diverse as their time of occurence... Sometimes it happens during gaming, sometimes when watching videos, sometimes when the computer is idle. These are the bluescreens I see most often: PAGE_FAULT_IN_NONPAGED_AREA KMODE_EXCEPTION_NOT_HANDLED IRQL_NOT_LESS_OR_EQUAL SYSTEM_SERVICE_EXCEPTION SYSTEM_THREAD_EXCEPTION INTERRUPT_EXCEPTION_NOT_HANDLED DRIVER_IRQL_NOT_LESS_OR_EQUAL DRIVER_OVERRAN_STACK_BUFFER Responsible drivers (according to the memory dumps): hal.dll tcpip.sys dxgmms1.sys ndis.sys mouhid.sys atikmdag.sys dump_atapi.sys and of course: ntoskrnl.exe My first thought was a driver incompatibility because I am using Windows 8 and some of the bluescreens seem to come from driver issues. All drivers are up to date. I'm afraid that my memory is broken or the mainboard or both. I used the windows integrated memtest which didn't find any errors. Memtest86 found some errors. Does it make sense to buy new memory? Couldn't it be a problem of the board as well? I also read that my memory could run at a too low voltage. But it's set to 1.5V as recommended. Another guess would be to set the memory's latencies manually, but how do I know which ones to try? Here is a screenshot of bluescreenview showing the latest bluescreens. Maybe someone has faced the same behavior before and found a solution. Any ideas or suggestions? Current setup on which the bluescreens occur. Windows 8 RTM (6.2.9200) Asrock 970 Extreme4 AMD FX-8150 ATI Radeon HD5850 16 GB RAM (DDR3-1800) Latest drivers for all devices

  Read the article

• Log shipping on select tables.

  - by Scott Chamberlain

  I know I am most likely using incorrect terminology so please correct me if I use the wrong terms so I can search better. We have a very large database at a client's site and we would like to have up to date copies of some of the tables sent across the internet to our servers at our office. We would like to only copy a few of the tables because the bandwidth requirement to do log shipping of the entire database (our current solution) is too high. Also replication directly to our servers is out of the question as our servers are not accessible from the internet and management does not want to do replication (more on that later). One possible Idea we had is to do some form of replication on the tables we need to another database on the same server and do log shipping of that second smaller database but management is concerned that the clients have broken replication (it was between two servers on their internal network however) on us in the past and would like to stay away from it if possible. Any recommendations would be greatly appreciated. If using some form of replication is the only solution, I am not against replication, I just need compelling arguments to convince management to do it. This is to be set up on multiple sites that are running either Sql2005 or Sql2008 we will have both versions on our end to restore the data to so that is not a issue. Thank you.

  Read the article

• Weird Apache Access Logs

  - by user38480

  I see repeated requests like these in my Apache Access Logs and they have been eating up all my CPU. I have a normal WordPress installation. All i changed in the Apache Configuration was changing the DocumentRoot from /var/www/html to /var/www for both ssl and the default configuration. Also, the file referenced in the requests(updatedll.jpeg) does not exist on my server and also isn't referenced in the source code served by any page of the web application. Could this be a security threat? What are these actually and what can i do to stop them. I changed the ip address of my server. They still kept coming. Meaning that somebody is actually hitting the domain name and not the ip address. Why does my server send a 301 for these requests? Shouldn't it be sending a 404? Is it because Wordpress is installed in my root directory and the .htaccess file present for Wordpress is sending a 301 redirect? My disk access logs also seem to have high peaks intermittently. But nobody is actually accessing the site. I see no access logs except these below. Also, i see that all the requests seem to be coming from one of the following 5 ip addresses. 201.4.132.43 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/4.0; BTRS103681; GTB7.5; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; InfoPath.2; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; AskTbATU3/5.15.29.67612; BRI/2)" 187.40.241.48 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; GTB7.5; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729)" 186.56.134.132 - - [05/Jun/2014:07:35:10 -0400] "GET /updatedll.jpg HTTP/1.0" 301 428 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 1.1.4322)" 71.223.252.14 - - [05/Jun/2014:07:35:13 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; BTRS31756; GTB7.5; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; .NET4.0C; .NET4.0E; InfoPath.2)" 85.245.229.167 - - [05/Jun/2014:07:35:14 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; Trident/7.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; MAAU; .NET4.0C; BRI/2; .NET4.0E; MAAU)"

  Read the article

• How do you enable view source in ie8 when it gets magically diabled

  - by Tim Meers

  I have multiple computers that all seem to have View Source disabled from the content menu when you right click on a web page. Now I know it's not that the web page is some how disabling it, I'm pretty sure thats not even possible. But alas I have at least 3 machines in my office (not on AD) that have this problem. I have also worked on clients computers that have this same issue. It's down right maddening! I tried to Google for it, but it just shows results from the dawn of IE6 in all of it's "glory" with a bug where if the cache was full it would be disabled. But this is not the case in IE8. Any body have a clue why this is happening, or a fix for it? Maybe a reg setting? Update: So I got a little closer to solving it, but there was still an issue on one computer where it allowed it not is HTTP, but not in HTTPS. One other computer works correctly in both. I Found these two keys missing in the registry: [-HKEY_CURRENT_USER\SOFTWARE\Microsoft\Internet Explorer\View Source Editor] [-HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Internet Explorer\View Source Editor]

  Read the article

• Azure Virtual Machines - what fault tolerance do they provide?

  - by Borek

  We are thinking about moving our virtual machines (Hyper-V VHDs) to Windows Azure but I haven't found much about what kind of fault tolerance that infrastructure provides. When I run VHD in Azure, I've got two questions: Is my VHD and all the data in it safe? I think that uploaded VHDs use the "Storage" infrastructure so they should be automatically replicated to multiple disks and geographically distributed but should I still make a full-image backup just to be safe? (Note that of course I will be backing up the actual data inside VMs that I care about; I just want to know if there is a chance greater than 0.0000001% that one day I will receive an email from Microsoft telling me that my VM is gone and that I should create or restore it from scratch). Do I need to worry about other things regarding the availability of my VMs? I mean, when I have an on-premise server I need to worry about the hardware itself, about the host operating system, what would happen if my router failed, if my Hyper-V's C: drive failed etc. Am I right in thinking that with Azure, their infrastructure takes care of all of this? Thanks.

  Read the article

• Symantec Backup Exec 12 Tape Alert.

  - by Adam

  Every day, I run 5 backups using 6 tapes. Each day, when I run the inventory, I get a tape alert Error. This occurs every day, on the same job. The error is: Job 'Inventory Daily ********' has reported Multiple Tape Alerts on server '******' Please refer to job log *****.xml for more information. When i look at the Job log, the Utility Job Information says: The device has reported the following TapeAlert diagnostic information Information- The library has been manually turned offline and is unavailable for use. Robotic library for device: PV132T 500 Warning - Library security has been compromised. Robotic Library for device: PV132T 500. Critical - The library has detected a inconsistency in its inventory. 1.Redo the library inventory to correct the inconsistency. 2. Restart the operation. Check the applications users manual or hardware users manual for specific instructions on redoing the library inventory. Roboric Library for Device PV132T 500. When I run the same inventory for a second time, the job completes successfully. I am using Symantec Backup Exec 12 running on Windows Server 2008. I am using a Dell Powervault 132T 500 tape drive. If anyone can help me on how to resolve this problem, it would be very much appreciated.

  Read the article

• Batch Script to Trim lines in text to first 30 or 50 characters only

  - by SuperUserMan

  I am now new to scripts but i find it really difficult understanding "for" command (especially with that tokens and delimiters etc) . Saying so, i think that for command can be used to do what i am doing. If its not and there is an easier way, ignore my ignorance :( Say i have multiple lines in a text file abc.txt with each line starting and ending with " (quotes) E.g. a file of 3 lines "hey what is going on @mike220. I am working on your car. Its engine is in very bad condition" "Because if you knew, you'd get shredded and do it with certainty" "@honey220 Do you know someone who has busted their ass on a diet only for results to come to a screeching halt after a few weeks" How can i trim each line, within the quotes, to a Fixed length say 30 or 50 or 100 characters (including spaces) I want to enter the number of character in batch and it can trim accordingly and produce a file def.txt with trimmed lines within quotes. Say i enter 50, results of above example should be "hey what is going on @mike220. I am working on you" "Because if you knew, you'd get shredded and do it" "@honey220 Do you know someone who has busted their" Thanks P.S. if you use For command, kindly please explain the command. EDIT: Though the answer provided worked, there is an issue with non english text. I am getting garbled text in Output file for non english text in input file . Any help @barlop here is the nonenglish text ( 1 line) "???? ?? ???? ?? ???? ???? ??? ?????? ???"

  Read the article

• Nginx Ubuntu Postfix Config - Can't connect to incoming IMAP server 'server not responding' but can send mail via outgoing using same details?

  - by daveaspinall

  I'm pretty to new server admin and especially nginx but seem to be getting ok fine apart from accessing my mail via my iPhone? I've changed my domain to 'domain.com' The thing is I can send mail via my outgoing IMAP server but can't connect to the incoming one? I just get the message "the mail server at mail.domain.com is not responding" /etc/postfix/main.cf alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix home_mailbox = Maildir/ inet_interfaces = all inet_protocols = all mailbox_command = mailbox_size_limit = 0 mydestination = domain.com, mail.domain.com, localhost.com, , localhost, localhost.localdomain mydomain = domain.com myhostname = mail.domain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname recipient_delimiter = + relayhost = smtp_tls_note_starttls_offer = yes smtp_tls_security_level = may smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = smtpd_sasl_security_options = noanonymous smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_auth_only = no smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_security_level = may smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom telnet localhost 25 ehlo locahost 250-mail.domain.com 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-AUTH LOGIN PLAIN 250-AUTH=LOGIN PLAIN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN Using the following details to connect: username password hostname: mail.domain.com port: 25 iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I also sent mail to the server as a test and got this missage if it helps? Technical details of temporary failure: [mail.domain.com. (10): Connection refused] I also looked in /var/log/mail.log and it has multiple entries of: postfix/smtpd[12239]: connect from 5acefc9a.bb.sky.com[90.206.252.xxx] Mar 23 06:47:09 new-domain postfix/smtpd[12239]: lost connection after CONNECT from 5acefc9a.bb.sky.com[90.206.252.154] Notice new-domain which is incorrect but the server hostname and hostname in the configs are correct? I recently moves servers and the host has set the primary domain on the service as new-domain.com so this may be the issue? Like I said, it works to connect to outgoing server, but incoming gets the not responding error? Any idea would be much appreciated!

  Read the article

• VPN service into 192 network

  - by tophersmith116

  I'm thinking about setting up a security testing lab. I work on a switched network, and that just makes for unnecessary headaches when doing testing. I'd like to create a 192 network with a few machines inside for DBs and AppServers etc. I will need a pivot machine that connects to both the outer network and the 192 (for automation purposes). But I'd like to be able to connect into the 192 network with my own machine from the outer network as the "attacking" machine (rather than have dedicated attack machines inside the 192 network). Therefore, I'd like to have the pivot server be a VPN server as well, so that my machine can VPN into the 192 network from the outer network. First off, is this even possible? Can I have a single computer with two NICs where a VPN service allows remote connections into the 192? Secondly, I'd like to have multiple outer clients connect to the VPN. Does anyone have any suggestions? I've used Hamachi well before, but I've also seen some good stuff from OpenVPN.

  Read the article

• What user information is exposed via a browser?

  - by ipso

  Is there a function or website that can collect and display ALL of the user information that can be obtained via a browser? Background: This of course does not account for the significant cross-reference abilities of large corporations to collate multiple sources and signals from users across various properties, but it's a first step. Ghostery is just a great idea; to show people all of the surreptitious scripts that run on any given website. But what information is available – what is the total set of values stored – that those scripts can collect from? If you login to a search engine and stay logged in but leave their tab, is that company still collecting your webpage viewing and activity from other tabs? Can past or future inputs to pages be captured – say comments on another website? What types of activities are stored as variables in the browser app that can be collected? This is surely a highly complex question, given to countless user scenarios – but my whole point is to be able to cut through all that – and just show the total set of data available at any given point in time. Then you can A/B test and see what is available with in a fresh session with one tab open vs. the same webpage but with 12 tabs open, and a full day of history to boot. (Latest Firefox & Chrome – on Win7, Win8 or Mint13 – although I'd like to think that won't make too much of a difference. Make assumptions. Simple is better.)

  Read the article

• WNDR3700 Router + Cisco SG200-08 + LACP + Dual Uplink

  - by kobaltz

  Background I have a storage server that has several virtual machine images stored on them. I would store them locally, but I have limited space on my desktop (using SSD storage). I would like to increase the bandwidth between the desktop and the storage server by using two NICs on each computer. My original configuration allowed about 55MBps between the desktop and storage server. This storage server also has several TBs of documents, pictures, movies, vms, and ISO/programs. The storage server has 8 1.5TB hard drives in a RAID 10 configuration with a hardware RAID controller. The benchmarks on the RAID 10 are about 300MBps. Configuration In short, I am trying to bridge my switch and router. The switch is a small 8 port Cisco smart switch that supports 802.3ad LACP. I have two computers plugged into the switch, each with 2 Intel Gigabit NICs. The first computer is a Windows 7 machine that has the Intel ANS software installed. I have LACP configured with the computer and now show 3 NICs (2 Physical + 1 TEAM Virtual @ 2Gbps). It looks like this computer is configured correctly. I trunked the two ports that this computer is plugged into with the switch's web interface. The second computer is a homebrew storage box running debian. I also have the bonding enabled on this machine and the switch configured with LACP. Without having the WNDR3700 router in the picture yet, I am able to communicate between the Windows 7 machine and the debian box since they both have static IP addresses. With LACP enabled on both machines I am getting about 106-108MBps speeds. Issue I plug in a network cable from the switch into the router and enable DHCP on the desktop. I saw no need to have a static address on the desktop. My transfer rates are still from 106MBps-108MBps. While this is still a boost, I am trying to figure out how to get about 140-180MBps. I am thinking that I need to increase the bandwidth from the router to the switch. My switch allows 4 groups for port trunking. I plugged in a second network cable from the router to the switch. My question is, what is the proper way to fix this issue. Should I port trunk the two ports that are going from the switch to the router? Keep in mind that the router is a WNDR3700 and is unsure whether or not it supports LACP. I do have OpenWRT installed on the router, but it still wasn't clear in any documentation that I found if it supported 802.3ad LACP standards. I am also wondering if there needs to be anything changed within the Cisco settings. [Edit] - Corrected some numbers, wasn't really paying attention. It looks like the speeds though at least two NICs are bonded with LACP is still reaching the max bandwidth of one port. Is there a way to configure the switch so that I can increase this bandwidth? Also, on the storage server, I had a couple of extra NICs laying around and threw them on there as well. Another EDIT and More Findings I happened to look at the traffic of each individual NIC and think that I see the problem. I tested with a simple transfer for a 4GB file. I noticed that only one of the NICs was taking the load of the traffic. I then copied the file back to the Storage Server and noticed that the other NIC was sending out the traffic. I have 802.3ad LACP enabled on the two NICs and I see that it gets enabled dynamically on the switch's interface. Should I be using Static Link Aggregation?

  Read the article

• No sound Ubuntu 10.10 (have SB Live! card)

  - by Chris Frazier

  I am new to Linux/Ubuntu and I just installed 10.10 on my Dell Desktop PC that was running Windows XP. The PC is about 5-6 years old and the sound card it has is a SoundBlaster Live! card. The Sound Preferences recognizes the card as [SB Live! Value] EMU10k1X. It is currently set to Analog Stereo Duplex. I tried multiple other sound configurations and nothing works. No sound but some clicks come out of the speakers. I ran the system test and during the audio tests the same thing happened, just clicks and pops. I tried to play some music with Rhythmbox and when it tries to play a track it tries for several seconds and then just closes itself, or sometimes just doesn't play. I ran a check for drivers, but the only driver it found to install was for my nVidia video card. It did not show any drivers for the sound card. Does anyone have any idea what I need to do to get the sound to work?

  Read the article

• iTunes Home Sharing only works one way between 2 Windows XP PC's on the same LAN

  - by scunliffe

  Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the Windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

  Read the article

• What are good systems for managing PHP/MySQL infrastructure?

  - by sbrattla

  I work in a company which is about to migrate most applications from in-house custom built Java/Tomcat applications to Drupal. Due to company policies, applications and websites need to run on in-house servers. This means that we need infrastructure for Drupal (PHP/MySQL) applications. This must have been solved a million times already. I believe this is what web-hosting companies does every day. Even though we work on a much smaller scale than web-hosting companies, i assume it would make sense to look at the task as if we're going to have an internal small-scale web-hosting company. This means that the guys in IT operations could be "responsible" for "offering" web-hosting, while developers could use these "services". We have three environments; dev(elopment), test and prod(uction). It would make sense that developers could log in to a system and create/edit/delete dev and test sites as they'd like. Production sites should be available through the same system, but only available to IT ops. We need to work with clusters of web servers, meaning that an administration system should be capable of creating/editing/deleting sites across multiple servers. I know there's no "this is it" answer to my question; but what would be a good place to start to get going with this? Apart from the actual hardware, what would be a good administration system for this?

  Read the article

• High speed network configuration

  - by Peter M

  Sorry if this seems to be a stupid question, I'm not sure how to specify what I want to know when checking google. I will have 2 or 3 devices pumping out data on a 100Base-T port. The combined data rate of all devices is about 15KB/S which exceeds the optimal 100Base-T channel capacity (12KB/S), but well within the realms of a 1000Base-T connection. Each device will be sending a burst of data in the form of an FTP transfer to a common, single host computer in a sequential manner ie: Device A establishes FTP connection and transfers data Device B establishes FTP connection and transfers data Device C establishes FTP connection and transfers data It may be that the A&B, B&C and C&A transfers overlap in the time domain to some extent. There will be minimal traffic going back from the computer to each device (in general what ever is needed to support the FTP transfers), and the network will be dedicated to transferring data between these devices and the host computer. Is it possible to use a switch to combine the multiple incoming 100Base-T streams into a single outgoing 1000Base-T stream? if so what features in a switch should I be looking for? Or would it be better to have 3 physical point-to-point 100Base-T dedicated connections between each device and the host computer? (thus having at least 3 physical Ethernet interfaces on that computer) Note that I can't change the interface on the devices, but I am free to choose the network and host computer configuration. Thanks for you help Peter

  Read the article

• amplified reflected attack on dns

  - by Mike Janson

  The term is new to me. So I have a few questions about it. I've heard it mostly happens with DNS servers? How do you protect against it? How do you know if your servers can be used as a victim? This is a configuration issue right? my named conf file include "/etc/rndc.key"; controls { inet 127.0.0.1 allow { localhost; } keys { "rndc-key"; }; }; options { /* make named use port 53 for the source of all queries, to allow * firewalls to block all ports except 53: */ // query-source port 53; /* We no longer enable this by default as the dns posion exploit has forced many providers to open up their firewalls a bit */ // Put files that named is allowed to write in the data/ directory: directory "/var/named"; // the default pid-file "/var/run/named/named.pid"; dump-file "data/cache_dump.db"; statistics-file "data/named_stats.txt"; /* memstatistics-file "data/named_mem_stats.txt"; */ allow-transfer {"none";}; }; logging { /* If you want to enable debugging, eg. using the 'rndc trace' command, * named will try to write the 'named.run' file in the $directory (/var/named"). * By default, SELinux policy does not allow named to modify the /var/named" directory, * so put the default debug log file in data/ : */ channel default_debug { file "data/named.run"; severity dynamic; }; }; view "localhost_resolver" { /* This view sets up named to be a localhost resolver ( caching only nameserver ). * If all you want is a caching-only nameserver, then you need only define this view: */ match-clients { 127.0.0.0/24; }; match-destinations { localhost; }; recursion yes; zone "." IN { type hint; file "/var/named/named.ca"; }; /* these are zones that contain definitions for all the localhost * names and addresses, as recommended in RFC1912 - these names should * ONLY be served to localhost clients: */ include "/var/named/named.rfc1912.zones"; }; view "internal" { /* This view will contain zones you want to serve only to "internal" clients that connect via your directly attached LAN interfaces - "localnets" . */ match-clients { localnets; }; match-destinations { localnets; }; recursion yes; zone "." IN { type hint; file "/var/named/named.ca"; }; // include "/var/named/named.rfc1912.zones"; // you should not serve your rfc1912 names to non-localhost clients. // These are your "authoritative" internal zones, and would probably // also be included in the "localhost_resolver" view above :

  Read the article

• Can a website company that builds 4-5 websites a year afford dedicated hosting?

  - by Petras

  We manage about 30 websites that use shared ASP.NET SQL Server web hosting. These are typical small/medium business websites and they perform fine in this environment. Recently I was looking at VPS hosting in this thread http://serverfault.com/questions/128329/how-do-you-host-multiple-public-facing-websites-on-a-vps After contacting a provider in one of the replies I was told that VPS hosting is not recommended for 30 sites, even if they are small. The resource requirements might be too great even for VPS. So I should turn to dedicated hosting. The lowest cost dedicated hosting is $219 per month (see http://www.serverintellect.com/dedicated/pentiumdservers.aspx). But this is only for a single processor which seems too light for a machine running both IIS and SQL. In our office all the developers work on quad cores so I assume I’d really need the Quad Processor. However, this starts at $599 monthly. Now, I won’t be able to transfer all of our 30 sites to this machine. I’d only be able to transfer say 5 or 6. However, moving forward, I’d be able to host all future sites on this machine. This amounts to 4-5 per year. Let’s look at the economics. Shared hosting costs are typically $16.95 monthly (see http://www.crystaltech.com/dotnet.aspx). So here’s the dilemma First months costs: $599 First month revenue: 6x$16.95 = $101.7 Loss in first month: $497.3 First year costs: $599x12=$7188 First month revenue: 6x$16.95x12 + 5x$16.95x6(averaged) = $1728.9 Loss in first year: $5459.1 Clearly it is going to take years for this server to pay for itself. It just doesn’t seem economical! Am I missing something here, or is dedicated not the way to go with the amount of sites we build?

  Read the article

• Textmate add multiline text at end of line

  - by Yuval

  In Textmate, I am able to add text to several lines at once by clicking and holding the Option key and dragging with the mouse. say I have the following lines: foo 1: foo 2: foo 3: I can easily click and hold option and then drag down with the lines to select the text at the end of each line, and then type "bar" once and it will be added to all lines, as such: foo 1: bar foo 2: bar foo 3: bar Fantastic. The problem I run into, is when my lines aren't the same length, as such foo 19: foo 37842342346: foo 503: Now if I want to add text to the end of each line, I have to either do it manually, or choose enough space so that the longest line is not overwritten, as such: foo 19: bar foo 37842342346: bar foo 503: bar This results in a lot of unwanted whitespace in lines that don't need it. Granted, I could easily run a regular expression search to replace all multiple occurrences of a space with a single one, but I was wondering if there's a way to select all ending of lines at once without having to do that. Any idea? Thanks!

  Read the article

• file system that allow to specify different RAID level per directory and change it afterward

  - by Adam Ryczkowski

  I have 5 hard drives, where I want to keep my data. Some of my files are more important, and some of them are less. So some of them I wish to put on RAID-6, and for some it RAID-5 is sufficient. It is difficult to predict at the moment of creation of the arrays how much space of each type to declare. What I would do if I didn't hear about zfs, is partition the hard drives into identical 100GB partitions, and as my needs grow, assemble those partitions into md devices using linux-raid. Then, I'd combine those devices using lvm into logical volumes where I'd put my data. So when I'd need more space of e.g. RAID-6, I'd take 100GB partition from each hard drive and assemble them into another RAID-6 md device and would use it as physical storage for the logical volume group dedicated for RAID-6 data. Then I could grow the file system on this logical volume. On top of RAID-6 and RAID-5 Volume Groups (managed by lvm) would reside completely independent file systems, which I'd later merge with multiple mount --bind into a single directory structure that would reflect the logical structure of data rather that of the storage. But now, when I heard about the ZFS with all the performance, data-healing and compression capabilities I cannot stop thinking if it can help me. If so, what do you think would be the best setup?

  Read the article

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Web based KVM management for Ubuntu

  - by Tim

  We've got a single Ubuntu 9.10 root server on which we want to run multiple KVM virtual machines. To administer these virtual machines I'd like a web based KVM management tool, but I don't know which one to choose from the list of tools mentioned on linux-kvm.org. I've used virsh & virt-manager on my desktop, but would like a web interface for the server. I tested ConVirt on my desktop, but it failed to pickup KVM machines from virsh / virt-manager, and I could not get KVM virtual machine import to work (only Xen). oVirt looks good, but I can't find out if and how I can install it on Ubuntu 9.10.. (And I'd really rather not waste another few days on testing stuff that might not work in the end.) Can anyone recommend any good web based KVM management tools that are easy to install on Ubuntu 9.10? I'm looking for something that will also allow me to run other services like apache and postgresql besides hosting virtual machines, so preferably fairly lightweight & no dedicated OS installs. We don't need any professional clustering / migration or anything, just something that will let us create, start, inspect, administer & stop virtual machines from a web page. Best regards, Tim Update: Anyone have any suggestions? It's awfully quiet here..

  Read the article

• Is 2 GB of RAM better than 2.5 GB?

  - by pibboater

  My laptop has two slots for RAM, and currently has two 512 MB chips, for 1 GB. Windows XP is running terribly slow on it, so I want to upgrade the RAM. I could buy two 1 GB chips to replace both of the current 512 MB chips, to give me 2 GB of RAM. Or, the price is the same to buy one 2 GB chip, to replace just one of the 512 MB chips, and give me 2.5 GB total. The RAM it takes is PC2-4200 533MHz DDR2. What do you think would be better: buying two 1 GB chips so it can take advantage of dual-channel operation, or buying one 2 GB chip to end up with more total RAM but not dual-channel operation? Like I said, price is the same, so performance is the only consideration. I'm not doing anything especially intensive like video or photo editing -- just having multiple Office programs open, playing music, browsers, etc., but currently even opening the first application takes forever. If it matters, the laptop is a Toshiba Qosmio G25-AV513 running Windows XP Media Center SP3. Thanks! Kevin

  Read the article

• User-unique .vimrc file for servers as root user

  - by Scott

  I'm getting thrown into an IDE war at the office, where multiple users have root access on our servers, and like to have everything their own way with VIM. Unfortunately, we have our servers locked down enough to where if you want to do anything, you need to have root access. Obviously (although this is obviously frowned upon), we get tired of typing sudo before each command we type, which would require that we constantly type in our wonderfully complex passwords that are mandated on us over and over again, so naturally we all just execute the sudo su - command upon login to avoid all of this. Of course, when it comes to VIM and custom .vimrc files, we are often times stepping on someone else's custom .vimrc file, and we have some whacked out functionality in these files that users have that may overwrite functionality that we have no idea about, much less have the patience to learn either. When as root on a linux box, is there any way for all of us to still maintain our .vimrc file without having to overwrite the file over and over again every time someone wants to use VIM? Ideally, we have many virtual machines all with VIM installed, so a universal solution across all servers would be best, and we do have our Microsoft Windows user specific home directories mounted on the servers under /home/username. Any recommendations for accommodating this?

  Read the article

• Users getting 'flooded' with not read notifications (NRNs) for old emails and meeting requests

  - by Exile

  I'm being placed under quite a lot of pressure from senior management over a relatively trivial issue. Basically the vast majority of users are complaining that they receive not read notifications (NRNs) for old emails and meeting requests in large numbers multiple times a day. I know something strange is happening because some are delivered at silly times in the morning (i.e 3AM or 4AM). The problem I have is that these some of these NRNs are from meeting requests and messages that are 120 days old, so some users have deleted the original message so I don’t actually know if the NRN is from an email or meeting request. This is typical of what users receive as a NRN: From: Sender Sent: 23 March 2012 04:16 To: Recepient Subject: Not read: Accepted: Status update Your message To: Sender Subject: Accepted: Status update Sent: Wednesday, November 23, 2011 8:59:00 AM (UTC) Dublin, Edinburgh, Lisbon, London was deleted without being read on Friday, March 23, 2012 4:15:32 AM (UTC) Dublin, Edinburgh, Lisbon, London. ... From: Sender Sent: 18 March 2012 01:13 To: Recepient Subject: Not read: Gold delivery - Sourcing module Your message To: Sender Subject: Gold delivery - Sourcing module Sent: Friday, November 18, 2011 9:37:58 AM (UTC) Dublin, Edinburgh, Lisbon, London was deleted without being read on Sunday, March 18, 2012 1:12:37 AM (UTC) Dublin, Edinburgh, Lisbon, London. I have done a search and found the following: http://support.microsoft.com/kb/2544246 http://support.microsoft.com/kb/2471964 But we already installed 'Update Rollup 6 for Exchange Server 2010 Service Pack 1' back in December, so I am not sure what we can do to fix this?

  Read the article

< Previous Page | 736 737 738 739 740 741 742 743 744 745 746 747  | Next Page >