Search Results

Search found 46419 results on 1857 pages for 'web traffic'.

Page 740/1857 | < Previous Page | 736 737 738 739 740 741 742 743 744 745 746 747  | Next Page >

  • Widespread misinterpretation of DNS rules in resolving wildcards

    - by Dominic Sayers
    [EDITED to add: This problem has gone away on its own. I believe Cloudflare's name resolution may have been to blame. See my own answer below] Here is a snippet of my zone file *.example.com. 300 IN CNAME proxy.herokuapp.com. foo.example.com. 300 IN A 111.111.111.111 If I dig @8.8.8.8 foo.example.com I get the answer I expect: ;; ANSWER SECTION: foo.example.com. 30 IN A 111.111.111.111 The same is true of all other public DNS servers I've tried. However, when I try to set up a check with Pingdom to a URL on foo.example.com it instead sends the traffic to my Heroku app referenced by the *.example.com RR. The same is true of checks set up on New Relic, Errplane and traffic generated by the Heroku app itself. So on the one side, all public DNS servers interpret the zone file one way. Yet four service providers all interpret it a different way, one that differs to the standard suggested by RFC 4592. My question is: are these reputable, mature service providers all wrong? Or is it little me?

    Read the article

  • Possible to IPSec VPN Tunnel Public IP Addresses?

    - by caleban
    A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

    Read the article

  • Poor SSL performance with vsftpd

    - by petrus
    I'm trying to tweak vsftpd to achieve maximum performance for my usage: I have only one or two clients that connect to the server. File size is between ~15MB and 1GB. Typical transfer batch represent between 1 and 2GB of data. For testing purposes, I'm using a tmpfs on both sides (thus eliminating any disks bottleneck) with a single 1GB file. When SSL is disabled, performance is good, with a transfer rate at ~120MB/s (reaching the limits of gigabit networking). With SSL enabled only for control traffic (and not data traffic), performance drops at about 112MB/s, which is still within the acceptable limits. However, when SSL is enabled for data flows, the transfer speed drops dramatically: 6.7MB/s using 3DES & SHA (ssl_ciphers=DES-CBC3-SHA in vsftpd.conf) 16MB/s using DES & SHA (ssl_ciphers=DES-CBC-SHA) I didn't tested other ciphers, but from what I can see from the CPU usage during the transfer, it seems that vsftpd is only using a single cpu/core per client. While this can fit for large ftp sites with hundreds of clients, I'd like to avoid this behavior and use more ressources on the server. On a side note, if you have any ideas regarding other openssl ciphers...

    Read the article

  • How to setup Mac server to use two gateways

    - by Brady
    I recently asked this question: How to set Mac server to use different Gateway for internet bound traffic The answer given works but has presented me with another issue that I didnt make clear in that question. Here is my network layout as it stands: At the moment outside staff members use some services on the existing internet 1 link. Those services are hosted by the Mac server. If I change the gateway of the Mac server to the second modem those outside staff lose visabilty on those services. Now I dont know how to go about solving this issue. I want the second link to be used when the Mac server goes to rsync data offsite but everything else use link one. How do I do this? Thanks Scott EDIT: This has been resolved by setting the default gateway on the Mac server to 192.168.1.254 Thus leaving everything on the network as it was before. but to get the Mac server to use the other link for rsync I've added a route to the Mac server to route traffic to the rsync server through the second gateway. sudo route add -net {server IP's}/{Netmask} 192.168.1.1 I've awarded the answer to gravyface for pointing me to a post on how to make this route persistant in Mac

    Read the article

  • Wireless Activity Monitoring for PCI DSS Compliance

    - by dkusleika
    In an effort to be PCI DSS compliant, I took a trustkeeper.net questionnaire. I failed the question that asks Is the presence of wireless access points tested for by using a wireless analyzer at least quarterly or by deploying a wireless IDS/IPS to identify all wireless devices in use? (SAQ #11.1) My only wireless access point is outside my firewall, so even if you cracked my wireless you couldn't get inside my domain (unless you crack that too). My firewall doesn't have IPS and I couldn't tell if it had IDS. I looked around for a wireless analyzer, but what I found was $500, which is a little pricey for my size business. And even if I got it, I'm not sure I would understand what it tells me. Surely there are smaller/less sophisticated businesses that take credit cards and have solved this. My questions are: What are the risks if someone were to crack my wireless? (Could they read all internet traffic? Just wireless traffic? Just use my internet connection?) And what is the best/cheapest way to test my connection point quarterly? Should I buy the $500 analyzer? Domain is Windows Server 2000. Firewall is Sonicwall Pro 2040. Router is 8 port D-link.

    Read the article

  • How do I create a wifi network bridge with qemu on OS X?

    - by a paid nerd
    I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

    Read the article

  • Issue with SSL using HAProxy and Nginx

    - by Ben Chiappetta
    I'm building a highly available site using a multiple HAProxy load balancers, Nginx web serves, and MySQL servers. The site needs to be able to survive load balancer or web servers nodes going offline without any interruption of service to visitors. Currently, I have two boxes running HAProxy sharing a virtual IP using keepalived, which forward to two web servers running Nginx, which then tie into two MySQL boxes using MySQL replication and sharing a virtual IP using heartbeat. Everything is working correctly except for SSL traffic over HAProxy. I'm running version 1.5 dev12 with openssl support compiled in. When I try to navigate to the virtual IP for haproxy over https, I get the message: The plain HTTP request was sent to HTTPS port. Here's my haproxy.cfg so far, which was mainly assembled from other posts: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice # log 127.0.0.1 local0 user haproxy group haproxy daemon maxconn 20000 defaults log global option dontlognull balance leastconn clitimeout 60000 srvtimeout 60000 contimeout 5000 retries 3 option redispatch listen front bind :80 bind :443 ssl crt /etc/pki/tls/certs/cert.pem mode http option http-server-close option forwardfor reqadd X-Forwarded-Proto:\ https if { is_ssl } reqadd X-Proto:\ SSL if { is_ssl } server web01 192.168.25.34 check inter 1s server web02 192.168.25.32 check inter 1s stats enable stats uri /stats stats realm HAProxy\ Statistics stats auth admin:********* Any idea why SSL traffic isn't being passed correctly? Also, any other changes you would recommend? I still need to configure logging, so don't worry about that section. Thanks in advance your help.

    Read the article

  • MS SQL Server Firewall Ports

    - by mmacaulay
    Hi, I've recently found myself in the position of quickly deploying a production app on SQL Server 2008 (EXPRESS), and I've been having some issues with configuring firewall rules between our web server running the ASP.NET app and our database server. Everything that I can find on the internet claims that I should only need to have TCP ports 1433/1434 and UDP port 1434 accessible on the database server. However, we were unable to get connectivity going between the web app and the database with just those ports. With the help of one of the guys in our datacentre, we discovered that there was traffic also going to TCP port 2242 on the database server. After opening this port, everything worked, but we're not sure why. Later on, I had to reinstall SQL Server due to some disk space issues, and found that the problem had resurfaced - after another session with the packet sniffer, we discovered that this time traffic was going to TCP port 4541 on the database server. My question is, is there some configuration option that I'm missing in SQL server that's making it choose random ports? I'd like to have our firewall rules locked down as much as possible, and of course we'd like to avoid any future mysterious connectivity issues, especially once the app is live. Both servers are running Windows 2003 R2 X64.

    Read the article

  • Cacti is ignoring hash marks in interface aliases

    - by Matt Simmons
    I'm attempting to set up Cacti to monitor a router's interfaces, and I'm having trouble getting the graph templates to show the information that I'd like. Our interface configuration looks like this: interface GigabitEthernet3/6 description WalljackNumber # Server info no ip address no shutdown switchport switchport access vlan 116 switchport mode access ip dhcp snooping trust spanning-tree portfast The "Server Info" string is really just the machine name, and a short relevant description, such as "PolarSprings vmnic2". The important part appears to be that it follows the hashmark. When I run snmpwalk, I get the proper output: IF-MIB::ifAlias.230 = STRING: WalljackNumber # Server info But in Cacti, when I go into the graph templates and set the title to this: |host_description| - Traffic - |query_ifName| (|query_ifAlias|) All that shows up in the graph is: switchname - Traffic - Gi3/6 (WalljackNumber #) Which strikes me as a little weird. What I suppose MAY be happening is that somewhere in the cacti stream, it's interpreting # as being a comment and stripping everything after, but I'm not sure. I was hoping someone could tell me that this was a known documented behavior, or that I could change it in a setting that I wasn't aware of. The alternative answer is to change the delimiter from # to something else, but I've got over a thousand lit switchports on an old college infrastructure, and I'm not sure what else might be relying on them.

    Read the article

  • Spammer relaying via Postfix mail server

    - by Paddington
    I have a Plesk 9.5 mail server (cm.snowbarre.co.za) on Ubuntu 8.04 LTS which forwards all SMTP traffic to an anti-spam server cacti.snowbarre.co.za. Many times I see the headers on the anti-spam server to contain from addresses not hosted on the mail server and I have checked and confirmed that my server is not an open relay server. How can a spammer be using my server to relay spam traffic? How can I stop this? Open relay test: paddington@paddington-MS-7387:~$ telnet cm 25 Trying 196.201.x.x... Connected to cm. Escape character is '^]'. 220 cm.snowbarre.co.za ESMTP Postfix (Ubuntu) mail from:[email protected] 250 2.1.0 Ok rcpt:[email protected] 221 2.7.0 Error: I can break rules, too. Goodbye. Connection closed by foreign host. paddington@paddington-MS-7387:~$ A typical headers is: *Received from cm.snowbarre.co.za (cm.snowbarre.co.za[196.201.x.x]) by cacti.snowbarre.co.za (Postfix) with ESMTPS id 00B601881AD; Mon, 27 Aug 2012 14:03:29 +0200 (SAST) Received from cm.snowbarre.co.za (localhost [127.0.0.1]) by cm.snowbarre.co.za (Postfix) with ESMTP id 81627367E007; Mon, 27 Aug 2012 14:02:50 +0200 (SAST) Received from User (ml82.128.x.x.multilinksg.com [82.128.x.x]) by cm.snowbarre.co.za (Postfix) with ESMTP; Mon, 27 Aug 2012 14:02:49 +0200 (SAST) Reply-To <[email protected]> From "Ms Nkeuri Aguiyi"<[email protected]> Subject Your Unpaid Fund. Date Mon, 27 Aug 2012 05:03:22 -0700 MIME-Version 1.0 Content-Type text/html; charset="Windows-1251" Content-Transfer-Encoding 7bit X-Priority 3 X-MSMail-Priority Normal X-Mailer Microsoft Outlook Express 6.00.2600.0000 X-MimeOLE Produced By Microsoft MimeOLE V6.00.2600.0000 X-Antivirus avast! (VPS 120821-0, 08/21/2012), Outbound message X-Antivirus-Status Clean Message-Id <[email protected]> To undisclosed-recipients:;*

    Read the article

  • SCM8014 to FVS338

    - by Jack
    I have a SMC8014 Router/Modem that Comcast provided me with their business class service. It was not filtering malicious traffic as aggressively as I had hoped, so I purchased a NetGear ProSafe FVS338, and put this behind the SMC8014, and all my machines behind that. After some brief configuration, all machines can see out to the internet. I also have a single web server, and I have not been able to configure things so that incoming requests can reach it. This is where I need help! I would like to have the FVS339 do NAT, so that I can assign a 192.168 address to my webserver. I've tried everything I know of, and I can't get things going. I set the SMC8014 to have a LAN facing IP of 10.0.0.1, and I assigned the FVS339 a WAN facing IP of 10.0.0.2. I would like to be able to tell the SMC8014 to just forward all traffic to 10.0.0.2, but I haven't had any success. In my (unfortunately limited) understanding, what I probably want here is a static route, but I don't know how to cofigure one, or if this is really what I want. The SMC8014 wants a Destination IP, a Subnet Mask and a Gateway IP. Any help would be appreciated.

    Read the article

  • Managing multiple Apache proxies simultaneously (mod_proxy_balancer)

    - by Hank
    The frontend of my web application is formed by currently two Apache reverse proxies, using mod_proxy_balancer to distribute traffic over a number of backend application servers. Both frontend reverse proxies, running on separate hosts, are accessible from the internet. DNS round robin distributes traffic over both. In the future, the number of reverse proxies is likely to grow, since the webapplication is very bandwidth-heavy. My question is: how do I keep the state of both reverse balancers / proxies in sync? For example, for maintenance purposes, I might want to reduce the load on one of the backend appservers. Currently I can do that by accessing the Balancer-Manager web form on each proxy, and change the distribution rules. But I have to do that on each proxy manually and make sure I enter the same stuff. Is it possible to "link" multiple instances of mod_proxy_balancer? Or is there a tool out there that connects to a number of instances, and updates all with the same information? Update: The tool should retrieve the runtime status and make runtime changes, just like the existing Balancer-Manager, only for a number of proxies - not just for one. Modification of configuration files is not what I'm interested in (as there are plenty tools for that).

    Read the article

  • VMware Server Host-Only Network Routing

    - by Chris
    I have a windows 2008 web server machine running VMware server. I have 3 VM's - All 3 are test servers so security isn't really a concern... each of them running windows 2008 standard and some of them serving web content. My ISP only allows one MAC address to access the physical switch, however they give me 10 public IP addresses to use. My question is, if I put each VM on their own Host only network, how can I route all traffic from a specific public IP on the host, to the corresponding host only adapter, therefore routing to the specific VM? For example: A single physical Adapter on the Host has the following public IP's assigned to it in windows networking: 74.208.14.10 74.208.14.20 74.208.14.30 Each VM is on a host-only network vm1 - 192.168.196.1 vm2 - 192.168.197.1 vm3 - 192.168.198.1 On the host, I want to route all traffic from 74.208.14.10 to VM1 and 74.208.14.20 to VM2 and 74.208.14.30 to vm3 without using VMware NAT, or bridged connections. I want each server to appear to have its own public IP address. My guess is i can modify the route tables somehow, or perhaps in ICS...but i'm not sure how.

    Read the article

  • ntop to analyse bandwidth usage on multiple ASA 5505

    - by dunxd
    I have set up a netflow server at our data centre, which is connected via VPN to ~40 remote offices using Cisco ASA 5505. The aim is to analyse usage data and find out exactly how the remote connections are being used. I followed through http://techowto.files.wordpress.com/2008/09/ntop-guide.pdf to set up ntop and https://supportforums.cisco.com/docs/DOC-6114 to set up the ASAs. I can see from the Plugin Netflow Statistics page that netflow packets from my ASAs are being received - the counter is increasing. However, I am not seeing any breakdown on the Global Traffic Statistic page after switching to the Netflow interface. I'm just seeing a pie chart showing 100% traffic for eth0. The interfaces and documentation are a little hard to follow so I am not sure I have got things configured correctly. When setting up my NetFlow-device.2 I can specify Virtual NetFlow Interface Network Address - the web UI says This value is in the form of a network address and mask on the network where the actual NetFlow probe is located. is this a Network address (e.g. 192.168.0.0/24) or an actual host IP address (192.167.0.1/24)? If that should be a network address, is this the network in which one of my ASAs is or the network in which my ntop server is? If a host IP address, is this the IP address used by eth0 on my ntop server, the IP address of an ASA, or something else? Do I need a separate virtual interface for each ASA I am collecting netflow data from? Any guidance would be greatly welcome.

    Read the article

  • How to set minimum SQL Server resource allocation for a database?

    - by Jeff Widmer
    Over the past Christmas holiday week, when the website I work on was experiencing very low traffic, we saw several Request timed out exceptions (one on each day 12/26, 12/28, 12/29, and 12/30) on several pages that require user authentication. We rarely saw Request timed out exceptions prior to this very low traffic week. We believe the timeouts were due to the database that it uses being "spun down" on the SQL Server and taking longer to spin up when a request came in. There are 2 databases on the SQL Server (SQL Server 2005), one which is specifically for this application and the other for the public facing website and for authentication; so in the case where users were not logged into the application (which definitely could have been for several hours at a time over Christmas week) the application database probably received no requests. We think at this point SQL Server reallocated resources to the other database and then when a request came in, extra time was needed to spin up the application database and the timeout occurred. Is there a way to tell SQL Server to give a minimum amount of resources to a database at all times?

    Read the article

  • Using IIS7 as a reverse proxy

    - by Eric Petroelje
    I'm setting up a server at home to host a few small websites. One of them is .NET based and needs IIS, the others are PHP based and need Apache. So, I have both IIS 7 and Apache 2.2.x installed on my server with IIS on port 80 and Apache running on port 8080. I would like to set up IIS to work as a reverse proxy, forwarding the requests for the Apache sites to port 8080 and serving the requests for the .NET site itself based on the host headers. Like this: www.mydotnetsite.com/* -> IIS -> serve from IIS www.myapachesite.com/* -> IIS -> forward to apache on port 8080 www.myothersite.com/* -> IIS -> forward to apache on port 8080 I did a bit of googling and it seemed like the Application Request Routing feature would do what I needed, but I can't seem to get it to work the way I want it to. I can get it to forward ALL traffic to the Apache server and I can get it to forward traffic with a specific URL pattern to the Apache server, but I can't seem to get it to forward based on the host headers (e.g. "forward all requests for www.apachesite.com - localhost:8080") So the question is, how would I go about configuring ARR to do this? Or do I need a different tool? I'm also open to using Apache as the reverse proxy and forwarding the .NET site requests to IIS instead if that's easier (running Apache on port 80 and IIS on 8080).

    Read the article

  • IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing problem

    - by Ernest Mueller
    Hey all, I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

    Read the article

  • VirtualBox: Can't get Bridged Networking to work (Win7 host)

    - by MikeTheTall
    I'm trying to set up a virtual LAMP server, including sharing files between the guest OS (Ubuntu Server) and the host OS (Windows 7) using samba. I think my problem is that I can't get Bridged (or Host-Only) networking to work in VirtualBox. I can boot the Linux VM just fine with NAT, but then can't access any services on it directly (except after port-forwarding port 80)(my understanding is that port-forwarding works because I'm not running a web server on the host OS, and therefore it can forward traffic to the unused port 80). I don't think that port-forwarding samba traffic (from the host to the guest) will work since I think that the host OS is using those ports. When I turn off NAT and turn bridged networking on I get an error. The VM fails to boot, with a dialog popping up (title: VirtualBox - Error) that says "Failed to open a session for the virtual machine UbuntuServer. Configuration error: Failed to get MAC address (VERR_CFGM_VALUE_NOT_FOUND). I'm hoping that once this is resolved then samba will work ok :) Any advice on this would be great (how to fix it would be wonderful, next steps for troubleshooting would be great, too :) )

    Read the article

  • Persistent routes for DD-WRT PPTP VPN client

    - by Tim Kemp
    My home network in the USA is behind a Buffalo router (G300NH) running their version of DD-WRT. I use the built-in PPTP VPN client to connect to a VPN provider in the UK. I route certain traffic over the VPN (so it has a UK source address, for various entirely legal reasons) which I achieved by following the instructions in the DD-WRT docs and my VPN provider's own instructions. I placed two commands like this in the firewall script: route add -net xxx.xxx.0.0 netmask 255.255.0.0 dev ppp0 route add -net yyy.yyy.0.0 netmask 255.255.0.0 dev ppp0 I didn't put any of the iptables rules in since it my setup doesn't seem to need them. It works like a charm. Traffic to the xxx subnets goes over the VPN, everything else goes out over my ISPs own pipes. The problem comes when the VPN drops, which it does occasionally. DD-WRT does a fine job of reconnecting it automatically, but the routes are trashed every time that happens. How do I automate the process of re-establishing my routes? I thought about static routes, but the IP address of the VPN connection is dynamically assigned (which is why I'm using dev ppp0). Many thanks, Tim

    Read the article

  • IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing issue

    - by Ernest Mueller
    I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

    Read the article

  • Setting up a network where packets are traced

    - by Marcus
    My situation is the following: I have an internet connection, which is shared between people. More or less obviously, people is using it to download illegal stuff. Since I'm the owner of the connection, I want to avoid being sued. I don't want to prevent the people from doing the things they want, but I want to be legally safe. Now, I have relatively little competences in network administration, so I was wondering: is it possible to setup a network, where the source and destination of the packets are logged? I would use this to prove, in case of lawsuit, that the traffic was coming from a given machine. if the idea is feasible, is there any wireless router on which I can install linux, where I can install the packet sniffer? how much space could the logs take (containing only the timestamp/source/destination), per GB of traffic? a very rough estimation would be very helpful. if a machine on my network is sending bittorrent packets to a certain IP, would this log be able to reflect the time, source ip and destination ip? I assume that obviously the torrent data would be encrypted and un-decryptable. Am I missing something? Is there a better strategy? Any pointer to documentation would be helpful as well - in that case, I would use this as starting point.

    Read the article

  • Route through site-to-site VPN not working

    - by Jonathan
    I'm trying to set up a site-to-site VPN using RRAS on two 2K8r2 servers since yesterday. The connection is working at this point, but I can't get it to send traffic from one site to the other one. Set up: the set up is the same on both sites: the server is connected to a router that's connected to a modem. The routers act like a DHCP-server and assign IP addresses from the range subnet.21-subnet-.100. Both servers use a static IP address, subnet.11, and are set up as DMZ. Configuration: the servers are configured using the wizard to set up a site-to-site connection. This works with a demand-dial interface and a PPTP VPN connection. As mentioned, the VPN connection work properly. Problem: I can't get the servers to send the traffic for the other site, to be sent through the VPN connection. I added a static route on both server (home, office 1) and I can see the result in the IP routing table (home, office 1). I did this because the route didn't show up automatically. My guess is that this last step isn't right, for example because the routing table states "non demand-dial", which seems not correct. Home: Subnet: 10.0.1.0/24 Router: 10.0.1.1 Server: 10.0.1.11 (DMZ) DHCP: 10.0.1.21-10.0.1.100 RRAS DHCP: 10.0.1.101-10.0.1.150 Office 1: Subnet: 10.0.2.0/24 Router: 10.0.2.1 Server: 10.0.2.11 (DMZ) DHCP: 10.0.2.21-10.0.2.100 RRAS DHCP: 10.0.2.101-10.0.2.150 I hope someone has an idea to get this route working!

    Read the article

  • Possible to IPSec VPN Tunnel Public IP Addresses?

    - by caleban
    A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

    Read the article

  • Same netmask or /32 for secondary IP on Linux

    - by derobert
    There appear to be (at least) two ways to add a secondary IP address to an interface on Linux. By secondary, I mean that it'll accept traffic to the IP address, and responses to connections made to that IP will use it as a source, but any traffic the box originates (e.g., an outgoing TCP connection) will not use the secondary address. Both ways start with adding the primary address, e.g., ip addr add 172.16.8.10/24 dev lan. Then I can add the secondary address with either a netmask of /24 (matching the primary) or /32. If I add it with a /24, it gets flagged secondary, so will not be used as the source of outgoing packets, but that leaves a risk of the two addresses being added in the wrong order by mistake. If I add it with /32, wrong order can't happen, but it doesn't get flagged as secondary, and I'm not sure what the bad effects of that may be. So, I'm wondering, which approach is least likely to break? (If it matters, the main service on this machine is MySQL, but it also runs NFSv3. I'm adding a second machine as a warm standby, and hope to switch between them by changing which owns the secondary IP.)

    Read the article

  • What was SPX from the IPX/SPX stack ever used for?

    - by Kumba
    Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

    Read the article

< Previous Page | 736 737 738 739 740 741 742 743 744 745 746 747  | Next Page >