Search Results

Search found 19782 results on 792 pages for 'device emulator manager'.

Page 741/792 | < Previous Page | 737 738 739 740 741 742 743 744 745 746 747 748  | Next Page >

• Second HDD not seen by Windows 7 on Dell Xps l501x

  - by George

  I have a Dell XPS Laptop (l501x). I have replaced the original Seagate 500GB hard drive with an SSD Intel 320 120GB when I first purchased it a year ago. It's been working great. The laptop is booting in about 23 seconds, so the SSD is great. I have an Acronis image created that I came back to every three months just to keep everything clean. The SSD is partitioned with one logical drive for my data. So, recently I thought since I am not using my optical drive often enough to swap it out with a HDD caddy and add my seagate 500gb hard drive. I ordered the caddy placed the HDD in it and now load Windows. It just hangs on the screen that should show the Windows logo. I have tried everything that I know and searched it online. I have uninstalled the SATA controller AHCI and let Windows install it. Still will not boot into windows. I wanted to mention that the Seagate 500GB drive was the one that came with my laptop before I switched to the Intel SSD. As you know Intel has this application called Intel Rapid Technology which loads once in a while and shows the second hard drive, but then, when I restart it hangs again and Windows will not load. As soon as I remove the HDD Caddy and restart it loads Windows fine. I also formated the Seagate 500GB HDD in NTFS and still Windows will not load. When I go into the BIOS it shows the Fixed SSD and also "Sata ODD 500GB" instead of the optical drive but it will not boot into Windows when the HDD caddy is present. There is nothing wrong with the caddy. I have another laptop (Asus) and I installed the HDD caddy and Windows 7 loads without any glitch. I don't get it. I have also flashed the BIOS because Dell had a new version (A08). I also wanted to add that I refreshed Disk Management and the Device Manager and the second drive does not display. At this point I think it's a Windows issue so before I reinstall Windows 7 Home Premium from scratch I wanted to see if there was anything I was missing. Any advice would be greatly appreciated.

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• Should use EXT4 or XFS to be able to 'sync'/backup to S3?

  - by Rafa

  It's my first message here, so bear with me... (I have already checked quite a few of the "Related Questions" suggested by the editor) Here's the setup, a brand new dedicated server (8GB RAM, some 140+ GB disk, Raid 1 via HW controller, 15000 RPM) it's a production web server (with MySQL in it, too, not just serving web requests); not a personal desktop computer or similar. Ubuntu Server 64bit 10.04 LTS We have an Amazon EC2+EBS setup with the EBS volume formatted as XFS for easily taking snapshots to S3, via AWS' console. We are now migrating to the dedicated server and I want to be able to backup our data to Amazon's S3. The main reason being the possibility of using the latest snapshot from an EC2 instance in case of hardware failure on the dedicated server. There are two approaches I am thinking of: do a "simple" file-based backup with rsync, dumping the database' and other files, and uploading to amazon via S3 API commands, or to an EC2 instance, or something. do a file-system "freeze" (using XFS) with the usual ebs/ec2 snapshot tool to take part of the file system, take a snapshot, and upload it to Amazon. Here's my question (or series of questions): Can I safely use XFS for the whole system as the main and only format on the dedicated server? If not, is it safe to use EXT4? Or should I use something else? would then be possible to make snapshots of the system to upload to Amazon? Is it possible/feasible/practical to do what I want to do, anyway? any recommendations? When searching around for S3/EBS/XFS, anything relevant to my problem is usually focused on taking snapshots of a XFS system that is already an EBS volume. My intention is to do it in a "real"/metal dedicated server. Update: I just saw this on Wikipedia: XFS does not provide direct support for snapshots, as it expects the snapshot process to be implemented by the volume manager. I had always assumed that I could choose 2 ways of doing snapshots: via LVM or via XFS (without LVM). After reading this, I realize these 2 options are more like it: With XFS: 1) do xfs_freeze; 2) copy the frozen files via, eg, rsync; 3) unfreeze xfs With LVM and XFS: 1) do xfs_freeze; 2) make a binary copy of the frozen fs via lvcreate and related commands; 3) unfreeze xfs; 4) somehow backup the LVM snapshot. Thanks a lot in advance, Let me know if I need to clarify something.

  Read the article

• Wifi randomly drops on Windows 8 laptop

  - by JosiahS

  First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

  Read the article

• Windows7 issue in mutli- tasking and memory

  - by Nitesh

  I seeming some problem in my windows OS recently, let me first say my system configuration. processor - Intel(R) Core(TM)2 Quad CPU Q8400 @ 2.66 GHz Installed memory (RAM) - 4.00 GB (3.00 GB usable) System type - 32 bit operating system I am using two OS in this system, first one is Windows7 and the other is centOS. Well, I am using this from a long time there was no problem , and all of a sudden since from couple weeks I am facing problems in my Windows7 OS. In windows7 i was nearing using multiple jobs almost every time i log in, there was no problem but now i don't no what happen I am not able to do multiple jobs at same time. For example- 1 I am now not able to listen to music in windows media player and view photo's. All of a sudden the system stops working and does not respond and then respond after 5mins and the music get played where it got stopped after 5 mins. 2 When i start browersing internet it hangs all of sudden and doesn't respond for 2 or 3 mins and gets loading. I mean it just happens for every operation i do in the system. Even now typing was also difficult, it gets hanged very frequently even though i am doing single task. I have never come across this kind of problem before. So the first thing i did was to see the useage of the processor and the memory. Well, i thick the useage of the processor was fine, for single task the useage was some where around 3 to 5%. Well, it was something weird i found in the memory, in spite of no task that i was running it was using somewhere around 34 to 41% of memory. So i opened the task manager and click on resource monitor in performance tab. And in the memory section of the monitoring tool i found the usage of my RAM, it was something like this. Hardware reserved - 1029 MB In Use - 1430 MB Modified - 49 MB Standby - 1566 MB free - 22 MB And i could also see Available 1588 MB Cached 1615 MB Total 3067 MB Installed 4096 MB well, this if all i could find out and i have no idea why my computer is acting so weird all of a sudden and the performance problem is growing day by day and i also don't know if there is problem in Bios, i have let it for default settings from long time. please help me and Thank you in advance for reading this and helping me.

  Read the article

• Squid on windows loadbalancing only to one server

  - by Martin L.

  After thousands of googles and trying days i cant get the load balancer/failover in squid on windows to work. Iam using squid 2.7. My webservers are 2 single NIC lighttpd and one dual nic lighttpd. server1 in this example is running squid on port 80 and lighttpd on port 8080 (just to test) Requirements: All 3 webservers running lighttpd should be balanced two option for load balancing: Best would be if server1 is busy server2 takes over, if server2 is busy server3 takes over, etc.. Round robin style evenly distributed load. Eg server1 takes first call, server2 second etc.. All requests should be treated the same way (no url rewriting or so on) Sent host headers have to be redirected to every server as http host header, speaking of "server1", "server1.company.internal" and "10.211.1.1". My approach: acl all src all acl manager proto cache_object http_port 80 accel defaultsite=server1.company.internal vhost #reverse proxy entries cache_peer 10.211.2.1 parent 8080 0 no-query originserver round-robin login=PASS name=server1_nic1 cache_peer 10.211.1.2 parent 80 0 no-query originserver round-robin login=PASS name=server2_nic1 cache_peer 10.211.2.3 parent 8080 0 no-query originserver round-robin login=PASS name=server3_nic1 cache_peer 10.211.2.4 parent 8080 0 no-query originserver round-robin login=PASS name=server3_nic2 #decl of names of squid host acl registered_name_hostdomain dstdomain server1.company.internal acl registered_name_host dstdomain server1 #ip of squid host acl registered_name_ip dstdomain 10.211.2.1 # access: redirects the correct squid hostname http_access allow registered_name_hostdomain http_access allow registered_name_host http_access allow registered_name_ip http_access deny all cache_peer_access server1_nic1 allow registered_name_hostdomain cache_peer_access server1_nic1 allow registered_name_host cache_peer_access server1_nic1 allow registered_name_ip cache_peer_access server2_nic1 allow registered_name_hostdomain cache_peer_access server2_nic1 allow registered_name_host cache_peer_access server2_nic1 allow registered_name_ip cache_peer_access server3_nic1 allow registered_name_hostdomain cache_peer_access server3_nic1 allow registered_name_host cache_peer_access server3_nic1 allow registered_name_ip cache_peer_access server3_nic2 allow registered_name_hostdomain cache_peer_access server3_nic2 allow registered_name_host cache_peer_access server3_nic2 allow registered_name_ip cache_peer_access server1_nic1 deny all cache_peer_access server2_nic1 deny all cache_peer_access server3_nic1 deny all cache_peer_access server3_nic2 deny all never_direct allow all Problems: Load balancer does not load balance other than to first server. Only if the first server is killed in any way the second will take over. I have seen the others working at some point, but definitely not as the intended load balancing described above. If the cache_peer_access is not defined sometimes the wrong hostname is sent to the backend webserver and this always depends on the defaultsite= parameter. Probably because the host header on the request to squid is not set and its replaced by defaultsite. Leaving out defaultsite didnt solve the problem. The only workaround i found for this is the current approach with cache_peer_access. Questions: Does the cache_peer_access influence the round-robin? Is there a better workaround to pass the host header to the backed webservers? Which parameters do increase the speed of load balancing or does anyone have a better approach? -Martin

  Read the article

• Moving default web site to another drive

  - by Chadworthington

  I set the default location from c:\inetpub\wwwroot to d:\inetpub\wwwroot but when I access my .NET 4.0 site get this error: Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 105: Set explicit="true" to force declaration of all variables. Line 106: --> Line 107: <compilation debug="true" strict="true" explicit="true" targetFramework="4.0"> Line 108: <assemblies> Line 109: <add assembly="System.Web.Extensions.Design, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"/> When I try to Manage the Basic Settings on the Site and click the "Test Settings" button, I see that I have a problem under "authorization:" The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that <domain>\<computer_name>$ has Read access to the physical path. Then test these settings again. 1) Do I need to grant rights to IIS to the new folder? Which user? I thought it was something like IIS_USER or something similar but I cannot determine the correct name of the user. 2) Also, do I need to set the default version of the framework somewhere at the Default Site level or at the Virtual folder level? How is this done in IIS6, I am used to IIS5 or whatever came with XP Pro. 3) My original site had a subfolder under wwwroot called "aspnet_client." How was this cleated? I manually copied it to the corresponding new location. My app was using seperate ASP specific databases for storing session state and role info, if that is relevant. Thanks

  Read the article

• How to make Windows 7 use the internet connection that I specify

  - by user138957

  I have a LAN adapter and a USB wireless internet connection. When both connected windows 7 always uses the USB. I tried changing the metric values but no luck. Let me explains the steps I took. Currently automatic metric on all adapters. LAN connected. ipconfig shows that it is connected to the correct ip/dns/gateway etc. IPv4 Route table shows Metric 24 Then connected USB. ipconfig shows USB connectivity then LAN in that order. Internet is now through USB. IPv4 Route table shows Metric 4249 for LAN and USB is 41. Gateway for USB shows "on-link". netstat -rn shows USBDEVICE on top. Changed LAN metric to 5 and now the route table shows LAN as 9 (not sure why it added 4) and USB as 41. netstat shows LAN then USB. ipconfig shows LAN then USB. But still connection is through USB. How do I know? Task manager shows utilization only through USB as well as speed is showing around 1mbps rather than LANs 10mbps. How can I get win7 use LAN while USB is connected. I am just trying to use USB as a backup just in case I lose LAN connection. Please help!! I thought i will make USB metric manually to say 10. But it says I have to reconnect for it to be effective. Currently USB still shows below LAN and still has 9 and 41 in the table. Disconnected USB. Table shows LAN metric as 24 (Not sure why it got changed from 9 and setting got reverted by to automatic) Reconnected USB. Now in the setting still shows 10 and the route table shows 11 for USB and LAN shows 4249 (settings shows 4245, 4 less)) For some reason restarting USB is resetting LAN setting when reconnected. Thanks

  Read the article

• High CPU usage - symptoms moving from server to server after bouncing

  - by grt3kl

  First off, I apologize if I didn't include enough information to properly troubleshoot this issue. This sort of thing isn't my specialty, so it is a learning process. If there's something I need to provide, please let me know and I'll be happy to do what I can. The images associated with my question are at the bottom of this post. We are dealing with a clustered environment of four WebLogic 9.2 Java application servers. The cluster utilizes a round-robin load algorithm. Other details include: Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_12-b04) BEA JRockit(R) (build R27.4.0-90_CR352234-91983-1.5.0_12-20071115-1605-linux-x86_64, compiled mode) Basically, I started looking at the servers' performance because our customers are seeing lots of lag at various times of the day. Our servers should easily handle the loads they are given, so it's not clear what's going on. Using HP Performance Manager, I generated some graphs that indicate that the CPU usage is completely out of whack. It seems that, at any given point, one or more of the servers has a CPU utilization of over 50%. I know this isn't particularly high, but I would say it is a red flag based on the CPU utilization of the other servers in the WebLogic cluster. Interesting things to note: The high CPU utilization was occurring only on server02 for several weeks. The server crashed (extremely rare; we are not sure if it's related to this) and upon starting it back up, the CPU utilization was normal on all 4 servers. We restarted all 4 managed servers and the application server (on server01) yesterday, on 2/28. As you can see, server03 and server04 picked up the behavior that was seen on server02 before. The CPU utilization is a Java process owned by the application user (appown). The number of transactions is consistent across all servers. It doesn't seem like any one server is actually handling more than another. If anyone has any ideas or can at least point me in the right direction, that would be great. Again, please let me know if there is any additional information I should post. Thanks!

  Read the article

• Windows 8 disk errors

  - by wrongusername

  So yesterday, I forcibly restarted my Windows 8 PC. VMWare Workstation was having some trouble with the guest Linux Mint OS. It wasn't responding for some time, so I tried suspending it September 28th or perhaps even before. It wouldn't suspend -- I forgot what the window looked like, but all options in the power menu were disabled (i.e. "Shutdown," "Power Off," and options like that were all disabled). I eventually killed the VMWare application through Task Manager, though I was too lazy to hunt down the running virtual machine itself, and decided to kill it by just shutting down my PC entirely. The PC wouldn't shut down for quite some time after the monitor went blank, so I did a cold reset by holding the power button. I then powered it on again and Windows briefly gave me some message like "Search for KERNEL_STACK_INPAGE_ERROR." Windows then started diagnosing some problems and gave me the message, "Repairing disk errors. This might take over an hour to complete." That was yesterday night, and I went to sleep without waiting for it to finish. This morning, it said that the repair failed, and that the log was at C:\windows\system32\LogFiles\srt\srtTrail.txt (as I remember it -- I don't have the exact path I wrote down right now). It gave me some other options to troubleshoot, such as resetting Windows (files and settings still intact, but programs not installed through the app store will be erased). That didn't work (no error message given, I was just told it didn't work). I tried rebooting in safe mode, the same diagnosis process begins, except that this time it doesn't bother with the automatic repairs again. So I tried using the command prompt to try to see if my files are at least still there. I was on the X drive, and I couldn't cd to the C drive. I couldn't find my folder under Users (of course?), and couldn't find the srt folder under LogFiles either. I am not sure what to try next. I have backed up everything, but to the cloud, so if absolutely necessary I can start off with a fresh copy of Windows and restore all my data, though it would be a hassle. Any thoughts on what might be wrong or what I can try? My computer was purchased just this June, so the hard drive should still be pretty new.

  Read the article

• How to use AD/GPO/Print Services to "push out" a new printer driver to replace a broken one? How did my server get a broken driver?

  - by Zac B

  Context: We have an AD/GPO-managed corporate network with a little over a hundred PCs running Windows 7 x64, and a few managed printers. Our Server2008R2 primary domain controller is configured as a print server for them all. Problem: After a recent windows update and restart (no printer driver updates were included) on the DC, a particular shared printer (Lexmark T650) has begin exhibiting some strange behavior. First, it prints a preceding and following blank page for almost every document, on jobs submitted by about half of client machines (no separator page is configured on the server or any of the clients I've seen). Second, whenever someone tries to access "Printing Preferences" on any client, they recieve the following error message (this happens everywhere, 100% of the time, and didn't happen before the update on the DC): Once they click "OK", the prefs screen appears (with no separator page selected) and everything seems fine. I'm not even sure if these two issues are related, but everyone seems affected by one or both of those issues. What I've Tried: I've been hesitant to un-deploy the problem printer, or remove it via GPO, as it's pretty heavily used. I've tried updating (via MS update and our internal WSUS server) client machines and the DC. No printer driver updates have appeared, and no number of updates or restarts on the server or the client seems to have achieved anything other than my boss getting grumpy that I'm bouncing the domain controller so often. I've tried deleting the drivers on the server, and re-installing them from the original source that has worked for the past year...no change. I've tried selecting "New Driver" for one of the shared printers on a client machine, running as domain admin, and pushed the latest driver found by MSupdate back up to the DC. This changed the version number of the driver recorded in the print server manager, but caused no change--on the client I pushed from, or on any other. The error still appears. Question: Why the heck is this happening? Obviously, I got a bad driver from somewhere, but how do I get rid of it? I don't know of any "roll back drivers" functionality for centrally managed print drivers like Windows offers for other devices. How would I a) get this issue resolved on a client, and b) push the fix to the other members of the domain?

  Read the article

• Possible HDD malfunction. Need help in diagnosing

  - by Protheus

  Today when using my PC as I did for almost 4 years I experienced the following: during opening new tab in Opera browser screen froze. Music (AIMP 3) continued to play for about 5 minutes and then stopped too. I tried Ctrl+Alt+Del, but win7 lock screen didn't appear. Caps\Scroll or Num locks didn't switch diodes on keyboard. I rebooted my PC and saw that BIOS suggests me to enter it's settings or load by default. I chose default. It don't see proper boot device (old faitful "insert proper boot" something). After second reboot it said that there is no ExpressGate installed (which i turned off in BIOS years ago). I went into BIOS setting to turn off ExpressGate and see configs: time was not set off, all hard drives present, temp and O.C. settings are nominal (no O.C.) I've inserted my Win7 install disk to try recovery. It did load awfully long (about few minutes) and didn't see current installation. PC was utilized in 24/7 mode for almost all these years. Hardware configuration: ASUS P5Q WS Core 2 Quad Q9300 (2.5GHz no O.C.) MSI geForce GTX 460 4x2 Gb GeIL EVO 2 (AFAIR) Seagate something 750Gb (4 years as system HDD 24/7) WD 1Tb (for random stuff, 5 y.o.) Hitachi 500Gb (for even more random stuff, 6 y.o.) NEC DVDRW (ALL DISKS ARE SATA) Cooler Master Silent Pro 700W Software: Windows 7 AND Kubuntu on the same drive with GRUB loader. Sorry I can't remember HDDs and can't see them right now, but I think their models aren't relevant anyway. My idea is that due to some system error or hard drive glitch i've wrecked my primary HDD's MBR. Nevertheless I don't exclude the possibility of other failure. May it's be that motherboard or it's SATA controller? Doubt it, because all drives are seen in BIOS and I could load from DVD. Maybe GRUB got bugged somehow, although I don't see how it's possible from Windows. But I did install KUbuntu from Windows (i wasn't myself then), maybe GRUB did write itself in some windows partition and got rewriteen in process? Right now I am at work with my flash drive with me and I need some advice how to fix MBR or to hear if it's not MBR. I'm going to buy new HDD (Hitachi 7k2000) because I think that my current HDD is compromised and it's unsafe to use it as system drive, especially 24/7.

  Read the article

• Routing between 2 different subnets on 2 different interfaces in SonicOS

  - by Chris1499

  I'm having a bit of a problem allowing traffic between two of my subnets. Here's the structure I've built. The X0 interface has our windows server on it and it handles DHCP/DNS, etc. X1 has the WAN connection. The Sonicwall is handling DHCP on X2. The X3 interface is connected to a different vlan on the 48 port switch. The Sonicwall is handling DHCP on this network as well. So here's what i want to do. The network on X2 is for our guest wireless; i don't want it to be able to access any of the other networks, just the internet, so i that all blocked in the firewall. No issues there. The X3 network is going to be for programmable controllers, and needs to be able to access the X0 network where our computers are. This is where my problem is. I'm not able to get between the 192.168.2.xxx and the 192.168.1.xxx on interfaces X0 and X3 respectively. I have these rules set up in the firewall. The Lan Primary Subnet is the 192.168.2.0 on X0. So if i'm not mistaken, this will allow traffic between the two through the firewall. Now this is where I'm a little confused. Do i need to use NAT to get the traffic from X0 to go to X3 (and vice versa), or a static route, or both? Currently i have both, though i doubt they're done correctly (also in screenshot). I've tried to ping between the two without luck. Any advice, or if you see what's wrong with my setup, is much appreciated. If you need some more information, let me know. Thanks all! EDIT: So i found that i don't neither either NAT or a static route, that the setting in the firewall is enough. I can now ping from the 192.168.1.xxx network, however i can't access the server on the 192.168.2.xxx network. When i try to access i get "An error occured while reconnecting to Z: to server Microsoft Windows Network: The local device name is already in use. This connection has not been restored. What am i missing?

  Read the article

• Slow WLAN file transfer between server and tablet

  - by user266985

  My file server is running Ubuntu 12.04 and I'm sharing files from it over samba. It is connected via gigabit ethernet. My desktop, running Windows 8.1, is also connected via gigabit ethernet. I can transfer files between the two and completely saturate that gigabit pipe. However, I just got a Surface Pro 2, and I'm trying to stream HD movies from my server to the device over WiFi. For some reason, I can't break much past 1.5MB/s transferring files over the network. I've tried streaming through XBMC and a standard file copy; no difference. To add the confusion, if I connect to my guest network and then use my VPN server (installed on the router) to access the file server, I get around 3.2MB/s. I've been running diagnostics to determine the root and I think I've found it but I have no idea what is causing it or how to fix it. Router: Asus RT-N66U Surface Pro 2 Network Card: Marvell Avastar 350N (Driver 19/09/2013 v14.69.24044.150) InSSIDer: Link Score: 100 Co-Channels: 0 Overlapping: 0 5GHz Network Channel: 48+44 iperf File Server as Server; Surface Pro 2 as Client - TCP Performance: Acceptable ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 4] local 192.168.0.90 port 5001 connected with 192.168.0.56 port 57367 [ ID] Interval Transfer Bandwidth [ 4] 0.0- 1.0 sec 10.1 MBytes 84.7 Mbits/sec [ 4] 1.0- 2.0 sec 10.4 MBytes 87.6 Mbits/sec [ 4] 2.0- 3.0 sec 10.6 MBytes 88.8 Mbits/sec [ 4] 3.0- 4.0 sec 10.7 MBytes 89.5 Mbits/sec [ 4] 4.0- 5.0 sec 10.1 MBytes 84.4 Mbits/sec [ 4] 5.0- 6.0 sec 10.2 MBytes 85.8 Mbits/sec [ 4] 6.0- 7.0 sec 7.04 MBytes 59.1 Mbits/sec [ 4] 7.0- 8.0 sec 10.8 MBytes 90.2 Mbits/sec [ 4] 8.0- 9.0 sec 10.6 MBytes 89.1 Mbits/sec [ 4] 9.0-10.0 sec 8.62 MBytes 72.3 Mbits/sec [ 4] 0.0-10.0 sec 99.2 MBytes 83.1 Mbits/sec iperf Surface Pro 2 as Server, File Server as Client Performance: Poor ------------------------------------------------------------ Client connecting to 192.168.0.56, TCP port 5001 TCP window size: 22.9 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.0.90 port 40233 connected with 192.168.0.56 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 1.0- 2.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 2.0- 3.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 3.0- 4.0 sec 1.25 MBytes 10.5 Mbits/sec [ 3] 4.0- 5.0 sec 1.62 MBytes 13.6 Mbits/sec [ 3] 5.0- 6.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 6.0- 7.0 sec 1.38 MBytes 11.5 Mbits/sec [ 3] 7.0- 8.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 8.0- 9.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 9.0-10.0 sec 1.62 MBytes 13.6 Mbits/sec [ 3] 0.0-10.1 sec 15.0 MBytes 12.4 Mbits/sec For some reason, it gets capped and I haven't got a clue why. Any suggestions? Edit: My link speed is reported as 270Mbps by Windows. I'm less than two metres from the router with a clear line of sight.

  Read the article

• Melting Laptop Power Supply Tip

  - by AlReece45

  Several (6-7) months ago, my laptop power supply cord got a cut in it and stopped working. Having gotten cheap (and short) power supplies in the past, I decided to buy 2 brand new ones from the manufacturer (ASUS). Now, I used my laptop a little less than usual between February and March. During that time I noticed a few times that the power supply, even though plugged in, did not provide power. Often the computer would just off on me. I figured it was just that one power supply being bad. I had left the alternate at my parent's house in another state and asked them to ship it to me. Now, at work the other day I wanted to get a file off the of hard disk. So I booted it up, knowing that it had a low battery, plugged it in. During the first 2 minutes of use, I was told that the battery was low and I should plug it in. I unplugged it, inspected the end (Being plugged in, this was suspicious), and decided I shouldn't plug it back in-- the plastic on the tip was melting from the heat of the metal on the tip. The computer had simply booted up and I had the file-manager open. It had not been on for more than 10 hours. Now I know that computers tend to get pretty hot. However, the melting point of plastic is usually above 200C.. so that's much hotter than the computer should be generating. I went and bought a THIRD power supply. This time a universal one from Best Buy (it was very fast to buy and test). I tried it out on the computer and it's tip is melting as well. My older laptop that uses the universal power supply uses it perfectly (has been about a week and a part of use now). I have tried using the computer without the battery, with the same effect. Obviously, this is not a problem with the power supply. My room mate and I being trained computer techs were contemplating taking the computer apart and desoldering and resoldering on the power tip. (The computer is about 6 months out of its 2-year warranty). We're hoping that will correct the issue as I would prefer to devote my money on a Good Desktop rather than yet ANOTHER $1200+ laptop. Is there any thing I'm missing here that might cause the the tip on the power unit to melt?

  Read the article

• New harddrives failing within weeks.

  - by Jason Kealey

  I've experienced 8 hard disk failures in 3 months and have tried many things to solve the issue permanently but I have failed. I would like to know if you have any advice for me. System was running Win XP on an Asus P5W-DH Deluxe. I have setup a RAID-1 array. I started out with 2 x 500 GB 7200RPM Western Digital drives. One died. I took it out to RMA it. On the same day, the router was fried. Assumed a power surge occurred; connected an older UPS to protect the system. Once I got my hands on an identical disk, I installed it. The RAID array was rebuilt. A few days later, the other one died. Assumed the rebuild caused it to fail. Took it out for RMA. Before the other one arrived, the remaining one died. I then discovered I could re-enable them using the Intel Matrix Storage Manager. I re-enabled both and the system seemed fine for a week, until both died again. I got two new 1.5 TB 7200RPM Seagate drives and re-installed Windows 7. Also replaced the UPS and power supply. They both died again. The voltage on the plug is stable between 120 and 122V as per the UPS. None of the other devices have had any problems (monitors, etc.). At this point, I see two options: a) electrical issue in the house that was, for some reason, not blocked by the UPS. b) something else inside the system causing surges? motherboard? onboard raid controller? Failures happen fairly quickly, between 2 and 14 days after I fix the previous issue. I just gotten a new computer (Core i7) to replace it. If it is stable, I can determine that b) was the problem. If it fries its hard drive again, I can determine that it is an electrical issue in the house. Do you have any other thoughts? Any tools I can run on the drives that failed to get more information about the original SMART event history?

  Read the article

• Why is Windows 7 not following all routes?

  - by GigabyteProductions

  My computer is connected to my secondary router that's running the 192.168.42.0/24 network and my computer also has a route that directs anything on that network to the router, but for anything on that network other than the router itself, it get's the ICMP response of Reply from 192.168.42.194: Destination host unreachable. (with 192.168.42.194 being my computer). Every other network works, like all of the internet, or addresses on my primary router like 192.168.1.*, just not on the 192.168.42.0/24 network... route print returns: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.42.1 192.168.42.194 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.42.0 255.255.255.0 On-link 192.168.42.194 276 192.168.42.194 255.255.255.255 On-link 192.168.42.194 276 192.168.42.255 255.255.255.255 On-link 192.168.42.194 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.42.194 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.42.194 276 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.42.1 Default =========================================================================== The only time anything is supposed to send an ICMP Host Unreachable response is when there's no route to it, right? So, why is my own computer sending that to ping or tracert when I have the route of 192.168.42.0 with the mask of 255.255.255.0? An IP address of 192.168.42.2 surely fits into that route. If I explicitly add a route for the IP address i am trying to access, it works, like: route add 192.168.42.2 mask 255.255.255.255 192.168.42.1 (the 192.168.42.1 right after mask is gateway, or the device to send the packet to so it can route it further), but why wont it work for the implicit route that's automatically on the table? I disabled my firewall, too (I use Comodo if anyone thinks this still serves as a problem). I'v even tried explicitly adding the gateway of 192.168.42.1 to the 192.168.42.0/24 route instead of it routing through 0.0.0.0's gateway, which is what On-link does. but that didn't work either, so it's not a gateway specification problem. If the host was really unreachable, it would be the router's IP address (192.168.42.1) sending that to me... This network is all of my creation, so there's no problem such as an administrator locking me out, because i am the administrator.

  Read the article

• Why would a process monitoring script use exit 1; on finding no problems?

  - by user568458

  General question: On a Linux (Centos) server, if a process monitoring script run by cron is set to close with exit 1; rather than exit 0; on finding that everything is okay and that no action is needed, is that a mistake? Or are there legitimate reasons for calling exit 1; instead of exit 0; on the "Everything's fine, no action needed" condition? exit 0; on finding no problems seems to me to be more appropriate. But maybe there's something I'm not aware of. For example, maybe there's something specific to Cron? Or maybe there's a convention in process monitoring scripts that 'failure' means 'this script failed to need to fix a problem' (rather than what I would expect which is that exit 1; would mean 'the process being monitored has failed'?) My specific case: I'm looking at a process monitoring script written by my web hosting company. By process monitoring script, I mean a script executed by Cron on a regular basis that checks if an important system process is running, and if it isn't running, takes actions such as mailing an administrator or restarting the process. Here's the (generalised) structure of their script, for a service running on port 8080 (in this case, Apache Tomcat): SERVICE=$(/usr/sbin/lsof -i tcp:8080 | wc -l); if [ $SERVICE != 0 ]; then exit 1; else #take action fi Seems simple enough even for someone with limited knowledge like me, except the exit 1; part seems odd. As I understand it, exit 0; closes a program and signifies to the parent that executed the program that everything is fine, exit n; where n0 and n<127 signifies that there has been some kind of error or problem. Here, their script seems to go against that rule - it calls exit 1; in the condition where everything is fine, and doesn't exit after taking remedial action in the problem condition. To me, this looks like a mistake - but my experience in this area is limited. Are there cases where calling exit 1; in the "Everything's fine, no action needed" condition is more appropriate than calling exit 0;? Or is it a mistake? Wider context is pretty simple. It's a Centos VPS, running Plesk. The script is being called by Cron via Plesk's "Scheduled tasks" Cron manager. There's no custom layer between Cron and this script that would respond in an unusual way to the exit call. It's a fairly average, almost out-of-the box Plesk-managed Centos VPS (in so far as there is such a thing). The process being monitored by this script is Apache Tomcat.

  Read the article

• Gentoo box can't cURL or ping after restarting net.eth1

  - by Curlybraces

  Hi all, the following is completely baffling me. We currently have a gentoo box which acts as our LAMP, DNS, DHCP server. This is assigned a static IP on the network. This server is connected directly to the internet via a BT BusinessHub Router. The server is also connected to a patch panel/switch port which connects the remaining office (around 10 PC's) to the server. Everything has been plain sailing until the other day when the server was restarted. For some reason now only portions of network accessibility is available depending on which ethernet device was last restarted. Restarting net.eth0 allows the office server to cURL, ping, etc but stops all networked PC's from accessing the internet. Then restarting net.eth1 restores all internet to the network but stops the server from curling, pinging, etc again. However, even when the server can't ping, curl, etc, I can still remote SSH and remote MySQL connect from the server command line to other external servers that we own. Here's my route map (router is 192.168.1.254): Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.1.254 0.0.0.0 UG 0 0 0 eth1 Here's my /etc/conf.d/net: iface_eth0="192.168.1.99 broadcast 192.168.1.255 netmask 255.255.255.0" iface_eth1="dhcp" None of the above have ever been changed however. Things have just ceased to operate correctly, which makes me think it's a freshly added Iptables rule. Here's the Iptables Filter table: Chain INPUT (policy ACCEPT) target prot opt source destination DROP tcp -- ##.##.##.## anywhere tcp dpt:ssh ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere tcp dpt:2199 ACCEPT tcp -- anywhere anywhere tcp dpt:3199 ACCEPT tcp -- ##.###.###.## anywhere tcp dpt:http ACCEPT tcp -- ###.###.##.## anywhere tcp dpt:2199 ACCEPT tcp -- ##.###.###.### anywhere tcp dpt:http ACCEPT tcp -- ##.###.##.## anywhere tcp dpt:http ACCEPT tcp -- ##.###.###.### anywhere tcp dpt:3128 ACCEPT udp -- ##.###.###.### anywhere udp dpt:3128 ACCEPT tcp -- ##.###.###.### anywhere tcp dpt:http ACCEPT tcp -- ##.###.###.### anywhere tcp dpt:https Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere ##.###.###.## DROP all -- anywhere ##.###.###.## ACCEPT all -- anywhere anywhere state NEW,ESTABLISHED Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp spt:2199 ACCEPT udp -- anywhere anywhere udp spt:4817 ACCEPT udp -- anywhere anywhere udp spt:4819 ACCEPT udp -- anywhere anywhere udp spt:3199 Help gratefully appreciated.

  Read the article

• I can't delete a directory inside a junctioned directory

  - by Fredy Muñoz

  So this is the deal. A couple of days ago I moved my profile folder C:\Documents and Settings\fmunoz to a different drive D:\fmunoz. Today, I created a directory in my desktop using the point-and-click method: Right-click on an empty space in the desktop Select New Select Folder Leave the default name New Folder and press Enter I tried to delete the folder using the point-and-click method: Right-click the New Folder directory Select Delete After five seconds, I got the following message: --------------------------- Error Deleting File or Folder --------------------------- Cannot delete New Folder: Access is denied. Make sure the disk is not full or write-protected and that the file is not currently in use. --------------------------- Initially I thought that there must be some sort of indexing services locking the directory so I got a list of open files using the TuneUp Process Manager tool but the New Folder directory wasn't there. I double-clicked My Computer, navigated to the desktop directory C:\Documents and Settings\fmunoz\Destkop, tried to delete the New Folder directory using the same point-and-click method described above and got exactly the same message at the same amount of time. In the same window, I navigated to the actual location of the desktop directory D:\fmunoz\Desktop, tried to delete the New Folder directory and this time it worked. I thought that this behavior was due to some special treatment that Windows gives to the desktop or the profile directories so I tried doing the same thing with a different set of directories: Created a folder D:\dummy Created a junction C:\dummy pointing to D:\dummy Created a New Folder directory in C:\dummy Tried to delete New Folder from C:\dummy. Didn't work. Tried to delete New Folder from D:\dummy. It worked. I tried creating the folder in the actual directory rather than the junction directory: Created a New Folder directory in D:\dummy Tried to delete New Folder from C:\dummy. Didn't work. Tried to delete New Folder from D:\dummy. It worked. I also tried using the Delete button instead of using the Delete option of the context menu but it didn't work. When using the Shift+Delete sequence, it works. It also works by using the rd command in the console, but in both cases the deleted directory doesn't goes to the Recycle Bin, which is my intention when using the Delete context menu option or the Delete button.

  Read the article

• How to run a restricted set of programs with Administrator privileges without giving up Admin acces (Win7 Pro)

  - by frLich

  I have a shared system, running Windows7 X64, restricted to a 'standard user' with no password. Not everyone who has access to the system has the administrator password. This works rather well, except for some applications - specially the unlock-applications for encrypted hard drives/USB flash drives. The specific ones either require Administrator access (eg. Seagate Blackarmor) or simply fail without it -- since these programs are sending raw commands to a device, this is to be expected. I would like to be able to add the hashes of these particular programs to a whitelist, and have them run as administrator without needing any prompts. Since these are by definition on removable media, I can't simply use a filename or even a path. One of the users who shares the system can be considered 'crafty', so anything which temporarily grants administrator rights to an user account is certain to cause problems. What i'd like to be able to do: 1) Create an admin account that can only run programs from a whitelist (or, failing that, from a directory) I can't find a good way to do this: As far as I can tell, SRP applies equally to ALL users? Even if I put a "Deny" token on all directories on the system, such that new directories would inherit it, it could still potentially run things from the mounted USB devices. I also don't know whether it's possible to create a new directory that DOESN'T inherit from the parent, that would lake the deny token, and provide admin access. 2) Find a lightweight service that will run these programs in its local context Windows7 seems to block cross-privilege level communication by default, and I haven't found such for windows 7. One example seems to be "sudo" (http://pages.cpsc.ucalgary.ca/~nfriess/sudo/) but because it uses a WLNOTIFY hook, it won't work under Vista nor Windows7 Non-Solutions: - RunAs: Requires administrator password! (but everyone calls it "sudo" anyway) - RunAs /savecred: Nice idea, but appears to be completely insecure. - RUNASSPC - Same concept as RunAs, uses "encrypted" files with credentials, but checks in user-space. - Scheduled Tasks - "Fixed" permissions make this difficult, and doesn't support interactive processes even if it did. - SuRun: From Google: "Surun uses its own Windows service that adds the user to the group of administrators during program start and removes him automatically from that group again"

  Read the article

• QNAP (469L) with Debian: can't connect to router

  - by agtoever

  I've been running my QNAP 469L with Debian (Wheezy deb7u3) for a few months. Yesterday I upgraded the memory to 4 GB. The system boots fine, but since the upgrade, I'm not able to connect the server to my router (a TP-Link WR941ND). My configuration: The router runs a DHCP server (192.168.67.100 and up), with a preconfigured ip address for the QNAP (192.168.67.10). The router is on 192.168.67.1. As said, Debian is installed on the QNAP (which can be regarded as a normal computer). Networking hardware on the QNAP: Intel PRO/1000 Network Connection using the e1000e kernel module. This is what I have tried so far: Replace the network cable (tried 3 different cables on different router ports). Check for messages from the kernel: dmesg | grep eth. Besides the normal hardware messages I get a ADDRCONF(NETDEV_UP): eth0: link is not ready for each call to ifup. Manually restart the network sudo server networking restart Check sudo ifconfig (eth0 is up, but no ip addresses). Check the /etc/network/interfaces which has (besides the loopback device) an allow-hotplug eth0 and iface eth0 inet dhcp, which is afaik the default Debian configuration. Since the server has two ethernet ports, I checked if I'm using the right port (checked the hardware address that ifconfig reports for eth0 is the same as the hardware address that is in the preconfigured ip address for the server in the router. Do a manual sudo ifdown eth0 && sudo ifup eth0 with no results (but an extra ADDRCONF(NETDEV_UP): eth0: link is not ready in the kernel log) Do a dhcp request dhclient -v eth0: for about a minute requests are send (according to the terminal) and at the end I get a No DHCPOFFERS received. No working leases in persistent database - sleeping.. Check the router system log if DHCP requests are received. I see them for some devices (my Mac, my iPhone) but not from the QNAP. The log entry looks like: DHCPS:Recv REQUEST from 84:85:06:07:75:6A and then a DHCPS:Send ACK to 192.168.67.101. There are no records from the QNAP's hardware address. So the two error messages that I do get are: ADDRCONF(NETDEV_UP): eth0: link is not ready for every ifup and No DHCPOFFERS received. No working leases in persistent database - sleeping. for every DHCP call.

  Read the article

• What is the difference between running a Windows service vs. running through shell?

  - by Zack

  I am trying to troubleshoot an issue on a Windows 2008 server where running attempting to connect to a "Timberline Data Source" ODBC driver crashes if the call is in a "service" context, but succeeds if the call is initiated manually in a Remote Desktop session. I have set the service to run as my user. I'm wondering if, all else being equal (user, machine, etc), are there any fundamental security/environment differences between running a process as a service vs manually? --- Implementation Details --- In case it is helpful for anyone, I had a system that started as an attempt to connect to a Timberline Database using ODBC and a Python CGI script called via IIS 7. The script itself works fine, however, as soon as I attempt to perform the ODBC connect function, the script crashes without throwing an exception. The script was able to connect fine when executed via command line. The same thing happened when using a C#/.net service, attempting to run via Apache, Windows Scheduler or even a 3rd party scheduling tool. With the last option (the 3rd party scheduling tool, pycron) I set the service up log in as my user and had the same issue (I confirmed via Task Manager that the process running user was, in fact, me). It just doesn't make sense to me why a service, which should be running as my user, appears to still be operating in a different security context or environment. Also, if it's important, the Timberline database is referenced by computer name on the network ("\\timberline-server\Timberline Office\Accounts\AT" or something to that effect) I also realized that, as Joel pointed out, the server DOES have a mapped drive ("Y:" which is mapped to "\\timberline-server\Timberline Office") The DSN is set up at the "System DSN" level which, according to the ODBC Administration Tool, means that the DSN is available to users and services Since I'm not allowed to answer this question yet, I'll post the solution that I arrived on: As Joel Coel mentioned, there actually was a mapped drive scenario. I didn't realize this because the DSN specified a path using UNC. However, it seems as though the actual Timberline Driver referred to a mapped drive. Since services don't start with the mapped drive, I was forced to add the drive mapping code into my service. Since it was written in python, I used code from a Stackoverflow answer that was able to map the drive on the fly.

  Read the article

• How to run a restricted set of programs with Administrator privileges without giving up Admin acces (Win7 Pro)

  - by frLich

  I have a shared system, running Windows7 X64, restricted to a 'standard user' with no password. Not everyone who has access to the system has the administrator password. This works rather well, except for some applications - specially the unlock-applications for encrypted hard drives/USB flash drives. The specific ones either require Administrator access (eg. Seagate Blackarmor) or simply fail without it -- since these programs are sending raw commands to a device, this is to be expected. I would like to be able to add the hashes of these particular programs to a whitelist, and have them run as administrator without needing any prompts. Since these are by definition on removable media, I can't simply use a filename or even a path. One of the users who shares the system can be considered 'crafty', so anything which temporarily grants administrator rights to an user account is certain to cause problems. What i'd like to be able to do: 1) Create an admin account that can only run programs from a whitelist (or, failing that, from a directory) I can't find a good way to do this: As far as I can tell, SRP applies equally to ALL users? Even if I put a "Deny" token on all directories on the system, such that new directories would inherit it, it could still potentially run things from the mounted USB devices. I also don't know whether it's possible to create a new directory that DOESN'T inherit from the parent, that would lake the deny token, and provide admin access. 2) Find a lightweight service that will run these programs in its local context Windows7 seems to block cross-privilege level communication by default, and I haven't found such for windows 7. One example seems to be "sudo" (http://pages.cpsc.ucalgary.ca/~nfriess/sudo/) but because it uses a WLNOTIFY hook, it won't work under Vista nor Windows7 Non-Solutions: - RunAs: Requires administrator password! (but everyone calls it "sudo" anyway) - RunAs /savecred: Nice idea, but appears to be completely insecure. - RUNASSPC - Same concept as RunAs, uses "encrypted" files with credentials, but checks in user-space. - Scheduled Tasks - "Fixed" permissions make this difficult, and doesn't support interactive processes even if it did. - SuRun: From Google: "Surun uses its own Windows service that adds the user to the group of administrators during program start and removes him automatically from that group again"

  Read the article

< Previous Page | 737 738 739 740 741 742 743 744 745 746 747 748  | Next Page >