Search Results

Search found 19332 results on 774 pages for 'hard drive'.

Page 745/774 | < Previous Page | 741 742 743 744 745 746 747 748 749 750 751 752  | Next Page >

  • Issues with Verizon's "Network Extender" device talking on my home network.

    - by Logan
    I recently switched my phone service to Verizon from ATT, and I get somewhat spotty service in my house. I called them and they sent me a "network extender" device for free. Its a femtocell that connects to my home network. The directions that come with it are very dumbed down, basically just say to connect it to your router and put it near a window (so it can get a GPS signal, it has to make sure its within the correct area before operating). The problem I'm having is the network light on it stays red. The troubleshooting information that came with it tells me this means there is a bad network connection. Its connected through an ASUS router running DD-WRT. No other devices on my network have a problem with it, including a Western Digital WDLIVE device, mine and my wife's cell phones (via wifi), a Wii, and an Xbox. If I connect the device directly to my cable modem, the light goes blue (which means good) and it starts working. So this tells me that its definately a configuration issue with my router. Verizon basically washed their hands of me when I connected it to my cable modem, and told me that its a router issue and to try a different router. Because normal people just have extra routers laying around their houses... When I connect it to the router, I can watch the DHCP Clients list on the status page, and the MAC of the network extender quickly fills up the clients list, grabbing every available DHCP address. Its like it grabs an address, can't connect to the internet, releases it, grabs another, then another, then another. So in the DHCP server settings I assigned a static IP to its MAC. This made it quit doing what it was doing before, but its still not working. I found the ports I needed to open on verizon's website, and opened them in the port forwarding config on my router. This still didn't help. So, I tried setting the network extender device's IP as the DMZ IP on the router. This still did no good. I called Verizon back and got the tech to write up a report which he passed on to a "senior network tech" who I got a call back from a few hours ago. This guy told me that while an ASUS router isn't listed as a supported device, he's not really sure why its not working. He suggested restoring the firmware to stock ASUS firmware and trying again. I have a very hard time believing its DD-WRT doing this, since every other device is working just fine with it. But its also not the Network Extender, since it works just fine when connected directly to the modem. At this point I'm out of ideas, and the next step is to restore the stock firmware on my router, and then going to walmart and getting a linksys WRT-54G to try. Is there anything else I could try before going that drastic? Cliffs- -Network extender won't work behind router, works when connected directly to cable modem. -Extender goes nuts when allowed to pick its own DHCP address, I had to assign it a static IP. -Won't work when correct ports are forwarded to it -Won't work with a DMZ address.

    Read the article

  • Starting MySQL database server: mysqld . . . . . . . . . . . . . . failed!

    - by meder
    I restarted my VPS box ( manually/hard restart ) and ever since, mysql fails to start for whatever reason. I did a tail /var/log/syslog and I get this: Feb 20 11:49:33 kyrgyznews mysqld[11461]: ) ;InnoDB: End of page dump 575 Feb 20 11:49:33 kyrgyznews mysqld[11461]: 110220 11:49:33 InnoDB: Page checksum 1045788239, prior-to-4.0.14-form checksum 236985105 576 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: stored checksum 1178062585, prior-to-4.0.14-form stored checksum 236985105 577 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Page lsn 0 10651, low 4 bytes of lsn at page end 10651 578 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Page number (if stored to page already) 3, 579 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: space id (if created with >= MySQL-4.1.1 and stored already) 0 580 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Database page corruption on disk or a failed 581 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: file read of page 3. 582 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: You may have to recover from a backup. 583 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: It is also possible that your operating 584 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: system has corrupted its own file cache 585 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: and rebooting your computer removes the 586 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: error. 587 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: If the corrupt page is an index page 588 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: you can also try to fix the corruption 589 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: by dumping, dropping, and reimporting 590 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: the corrupt table. You can use CHECK 591 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: TABLE to scan your table for corruption. 592 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: See also InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html 593 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: about forcing recovery. 594 Feb 20 11:49:33 kyrgyznews mysqld[11461]: InnoDB: Ending processing because of a corrupt database page. 595 Feb 20 11:49:33 kyrgyznews mysqld_safe[11469]: ended 596 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: 0 processes alive and '/usr/bin/mysqladmin --defaults-file=/etc/mysql/debian.cnf ping' resulted in 597 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: ^G/usr/bin/mysqladmin: connect to server at 'localhost' failed 598 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: error: 'Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2)' 599 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: Check that mysqld is running and that the socket: '/var/run/mysqld/mysqld.sock' exists! 600 Feb 20 11:49:47 kyrgyznews /etc/init.d/mysql[12228]: 601 Feb 20 11:49:56 kyrgyznews mysqld_safe[13437]: started 602 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: The log sequence number in ibdata files does not match 603 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: the log sequence number in the ib_logfiles! 604 Feb 20 11:49:56 kyrgyznews mysqld[13440]: 110220 11:49:56 InnoDB: Database was not shut down normally! 605 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Starting crash recovery. 606 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Reading tablespace information from the .ibd files... 607 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Restoring possible half-written data pages from the doublewrite 608 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: buffer... 609 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: Database page corruption on disk or a failed 610 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: file read of page 3. 611 Feb 20 11:49:56 kyrgyznews mysqld[13440]: InnoDB: You may have to recover from a backup. I have looked at the page it referenced, http://dev.mysql.com/doc/refman/5.0/en/forcing-innodb-recovery.html, but before messing with any settings I was wondering what experienced DBAs would suggest doing? Is there any harm in forcing the recovery? PS - I did not make any updates to mysql. Version is mysql Ver 14.12 Distrib 5.0.51a, for debian-linux-gnu (i486) using readline 5.2.

    Read the article

  • How to stop Apache from crashing my entire server?

    - by CyberShadow
    I maintain a Gentoo server with a few services, including Apache. It's fairly low-end (2GB of RAM and a low-end CPU with 2 cores). My problem is that, despite my best efforts, an over-loaded Apache crashes the entire server. In fact, at this point I'm close to being convinced that Linux is a horrible operating system that isn't worth anyone's time looking for stability under load. Things I tried: Adjusting oom_adj for the root Apache process (and thus all its children). That had close to no effect. When Apache was overloaded it would bring the system to a grind, as the system paged out everything else before it got to kill anything. Turning off swap. Didn't help, it would unload memory paged to binaries of processes and other files on /, thus causing the same effect. Putting it in a memory-limited cgroup (limited to 512 MB of RAM, 1/4th of the total). This "worked", at least in my own stress tests - except the server keeps crashing under load (basically stalling all other processes, inaccessible via SSH, etc.) Running it with idle I/O priority. This wasn't a very good idea in the end, because it just caused the system load to climb indefinitely (into the thousands) with almost no visible effect - until you tried to access an unbuffered part of the disk. This caused the task to freeze. (So much for good I/O scheduling, eh?) Limiting the number of concurrent connections to Apache. Setting the number too low caused web sites to become unresponsive due to most slots being occupied with long requests (file downloads). I tried various Apache MPMs without much success (prefork, event, itk). Switching from prefork/event+php-cgi+suphp to itk+mod_php. This improved performance, but didn't solve the actual problem. Switching I/O schedulers (cfq to deadline). Just to stress this out: I don't care if Apache itself goes down under load, I just want the rest of my system to remain stable. Of course, having Apache recover quickly after a brief period of intensive load would be great to have, but one step at a time. Right now I am mostly dumbfounded by how can humanity, in this day and age, design an operating system where such a seemingly simple task (don't allow one system component to crash the entire system) seems practically impossible - or at least, very hard to do. Please don't suggest things like VMs or "BUY MORE RAM". Some more information gathered with a friend's help: The processes hang when the cgroup oom killer is invoked. Here's the call trace: [<ffffffff8104b94b>] ? prepare_to_wait+0x70/0x7b [<ffffffff810a9c73>] mem_cgroup_handle_oom+0xdf/0x180 [<ffffffff810a9559>] ? memcg_oom_wake_function+0x0/0x6d [<ffffffff810aa041>] __mem_cgroup_try_charge+0x32d/0x478 [<ffffffff810aac67>] mem_cgroup_charge_common+0x48/0x73 [<ffffffff81081c98>] ? __lru_cache_add+0x60/0x62 [<ffffffff810aadc3>] mem_cgroup_newpage_charge+0x3b/0x4a [<ffffffff8108ec38>] handle_mm_fault+0x305/0x8cf [<ffffffff813c6276>] ? schedule+0x6ae/0x6fb [<ffffffff8101f568>] do_page_fault+0x214/0x22b [<ffffffff813c7e1f>] page_fault+0x1f/0x30 At this point, the apache memory cgroup is practically deadlocked, and burning CPU in syscalls (all with the above call trace). This seems like a problem in the cgroup implementation...

    Read the article

  • Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

    - by Joe Hopfgartner
    I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

    Read the article

  • Intermittent lockups, unable to diagnose in over a year

    - by Magsol
    Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

    Read the article

  • XenServer Converting HVM to Paravirtualised

    - by Karl Kloppenborg
    Recently I have been tasked with the daunting process of converting a setup of HVM enabled VMs (running on Citrix XenServer 5.6.0) into PV (paravirtualised) containers. The constraints of the project was that: The operating system must be functionally identical after the migration. minimal modification to the operating system (with exception of kernel / drive mapping) I also was allowed to change the bootloader(ie, grub) in what ever way I see fit. However, I have attempted this, I will firstly like to show you my steps I took. This at the moment is CentOS5.5 specific: Steps: yum install kernel-xen This installed: 2.6.18-194.32.1.el5xen edited: /boot/grub/menu.lst changed my specs to match: title CentOS (2.6.18-194.32.1.el5xen) root (hd0,0) kernel /vmlinuz-2.6.18-194.32.1.el5xen ro root=/dev/VolGroup00/LogVol00 console=xvc0 initrd /initrd-2.6.18-194.32.1.el5xen.img Then I changed my xenserver parameters to match: xe vm-param-set uuid=[vm uuid] PV-bootloader-args="--kernel /vmlinuz-2.6.18-194.32.1.el5xen --ramdisk /initrd-2.6.18-194.32.1.el5xen.img" xe vm-param-set uuid=[vm uuid] HVM-boot-policy="" xe vm-param-set uuid=[vm uuid] PV-bootloader=pygrub xe vbd-param-set uuid==[Virtual Block Device/VBD uuid] bootable=true Some things to note, I am running a VolGroup LVM ;) Anyways, after all these steps (which aren't much!) I boot the VM and it boots initial kernel just fine, however I am presented with this error: Boot Screen: device-mapper: dm-raid45: initialized v0.2594l Waiting for driver initialization. Scanning and configuring dmraid supported devices Scanning logical volumes Reading all physical volumes. This may take a while... Activating logical volumes Volume group "VolGroup00" not found Creating root device. Mounting root filesystem. mount: could not find filesystem '/dev/root' Setting up other filesystems. Setting up new root fs setuproot: moving /dev failed: No such file or directory no fstab.sys, mounting internal defaults setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys switchroot: mount failed: No such file or directory Now my hints are that it cannot detect / because of the fact that when you change from HVM mode to PV it does something (not that obvious) When you make a SR (storage) on a HVM, you get it mounted to the guest os as /dev/hda. However in PV mode, this presents itself as /dev/xvda... Could this be the answer? and if so, how the heck to I implement it?? Update: So I have gotten a bit further in my quest, as it now detects the LVM's... To do this, I required to recompile the xen-kernel initrd image. Command: mkinitrd -v --builtin=xen_vbd --preload=xenblk initrd-2.6.18-194.32.1.el5xen.img 2.6.18-194.32.1.el5xen Now when I boot I get this: Boot Screen: Loading dm-raid45.ko module device-mapper: dm-raid45: initialized v0.2594l Scanning and configuring dmraid supported devices Scanning logical volumes Reading all physical volumes. This may take a while... Found volume group "VolGroup00" using metadata type lvm2 Activating logical volumes 3 logical volume(s) in volume group "VolGroup00" now active Creating root device. Mounting root filesystem. mount: error mounting /dev/root on /sysroot as ext3: Device or resource busy Setting up other filesystems. Setting up new root fs setuproot: moving /dev failed: No such file or directory no fstab.sys, mounting internal defaults setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys switchroot: mount failed: No such file or directory Kernel panic - not syncing: Attempted to kill init!

    Read the article

  • what is the best mid/high-end class audio/music creation audio sound card?

    - by Chris
    Hello, I have a computershop myself, and I repair computers. But one of the things I really don't know (yet) is the performace od audio cards for music creation with midi. I have searched and searched and came up with some good reviews, but after browsing for a couple of hours I could't see the trees trough the forrest :-D (it's a dutch expression) At one moment I thought the M-Audio - Delta 1010LT would be a good PCIe card, later on I read that this card was released years ago. (but that could be false information) Also any personal expierence would be great, but not necessairy. I have searched a few cards, and I hope someone can help me make a choice for a friend of mine. He's buget is between $100 and $350 I know there are audio cards from $ 500 - $1850,- this is just too expensive. The following specs are crucial: ASIO Midi Mic in minimal 5.1, 7.1 recommended it's not for airplay, but just to compose music at home. using Ableton and midi keyboard. 1. M-Audio - Delta 1010LT: 8 x 8 analog I/O 2 mic preamps or line inputs S/PDIF digital I/O (coaxial) with 2-channel PCM SCMS copy protection control digital I/O supports surround-encoded AC-3 and DTS pass-through 1 x 1 MIDI I/O directly drive up to 7.1 surround (bass management software included) software controlled 36-bit internal DSP digital mixing/routing +4dbu/-10dBV operation individually switched in software word clock I/O for sample accurate device synchronization 2. RME HDSP 9632: * Stereo Analog Ein- und Ausgang, symmetrisch*, 24-Bit/192kHz, > 110 dB SNR * Optionale Erweiterungsboards mit je 4 symmetrischen Ein- und Ausgängen * Alle analogen I/Os voll 192 kHz-fähig, also keine Reduzierung der Kanalzahl * 1 x ADAT Digital In/Out, 96 kHz-fähig (S/MUX) * 1 x SPDIF Digital In/Out, 192 kHz-fähig * 1 x Breakout Kabel für koaxialen SPDIF-Betrieb* * Also bis zu 16 Ein-und Ausgänge gleichzeitig nutzbar! * 1 x Stereo Kopfhörerausgang, parallel zum analogen Ausgang, aber eigene Pegelanpassung * 1 x MIDI I/O für 16 Kanäle Hi-Speed MIDI über Breakout Kabel * DIGICheck, RMEs einzigartiges Meter- und Analysetool mit Spectral Analyser, Professionelle Level Meter 2/8/16-Kanalig, Vector Audio Scope und diversen weiteren Analysefunktionen * HDSP Meter Bridge: Frei skalierbare Levelmeter mit Peak- und RMS Berechnung in Hardware * TotalMix: 512-Kanal Mischer mit 40 Bit interner Auflösung 3. EMU 1212M (1212 M) PCIe: * Top kwaliteit convertors 24-bit/192kHz convertors. * Hardware gestuurde effecten. * DSP zero-latency hardware mixen en monitoring. * Analoge en digitale I/O plus MIDI. * EMU Production Tools Software Bundle - Cakewalk SONAR , Steinberg Cubase LE, Ableton Live E-MU Edition **EMU 1212M PCI-e inputs/outputs:** * 2 balanced jack inputs. * 2 balanced jack outputs. * 24-bit/192kHz ADAT I/O. * 24-bit/192kHz Coaxiale S/PDif I/O switchable to AES/EBU. * MIDI I/O. 4. M-Audio Audiophile 192: - Up to 24-bit/192kHz audio - 2 balanced analog inputs (1/4” TRS) - 2 balanced analog outputs (1/4” TRS) - S/PDIF digital I/O (coaxial RCA connectors) with 2-channel PCM - SCMS copy protection control - Digital I/O supports surround-encoded AC-3 and DTS pass-through - Direct hardware input monitoring via separate balanced 1/4” TRS monitor outputs - Software routing of inputs and outputs - Digital I/O can be routed to/from external effects - 16-channel MIDI I/O - ASIO, WDM, GSIF 2 and Core Audio driver support for compatibility with most applications - 64-bit driver support for Windows - PCI 2.2 compatibility - Apple G5 compatible - Incompatible exceptions - Includes Ableton Live Lite music production software, so you can make music right away - Works with other Delta cards Technical Specifcations: - Compatibility - ASIO - WDM - GSIF 2 - Core Audio

    Read the article

  • How to diagnose computer lockups and freezes?

    - by Scott Mitchell
    I built a desktop computer a couple years back with the following specs: CPU: Intel Core 2 Quad Q9300 Yorkfield 2.5GHz 6 MB L2 Cache LGA 775 95W Quad-Core Processor BX80580Q9300 Motherboard: EVGA 122-CK-NF68-T1 LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard Video Card: Two EVGA 256-P2-N758-TR GeForce 8600GT SCC 256 MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card PSU: SeaSonic S12 Energy Plus SS-550HT 550W ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS Certified Active PFC Power Supply Memory: Two G.SKILL 4 GB (2 x 2 GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model F2-6400CL5D-4GBPQ Since its inception, the machine has periodically locked up, the regularity having varied over the years from once a day to once a month. Typically, lockups happen once every few days. By "lockup" I mean my computer just freezes. The screen locks up, I can't move the mouse. Hitting keys on my keyboard that normally turn LEDs on or off on the keyboard (such as Caps Lock) no longer turn the LEDs on or off. If there was music playing at the time of the lockup, noise keeps coming out of the speakers, but it's just the current frequency/note that plays indefinitely. There is no BSOD. When such a lockup occurs I have to do a hard reboot by either turning off the computer or hitting the reset button. I have the most recent version of the NVIDIA hardware drivers, and update them semi-regularly, but that hasn't seemed to help. I am currently using Windows 7 x64, but was previously using Windows Server 2003 x64 and having the same lockup issues. My guess is that it's somehow video driver or motherboard related, but I don't know how to go about diagnosing this problem to narrow down which of the two is the culprit. Additional information re: cooling Regarding cooling... I've not installed any after-market cooling systems aside from two regular fans I scavenged from an older computer. The fan atop the CPU is the one that shipped with it. One of the two scavenged fans I added it located at the bottom tower of the corner, in an attempt to create some airflow from front to back. The second fan is pointed directly at the two video cards. SpeedFan installation and readings Per studiohack's suggestion, I installed SpeedFan, which provided the following temperature readings: GPU: 63C GPU: 65C System: 76C CPU: 64C AUX: 36C Core 0: 78C Core 1: 76C Core 2: 79C Core 3: 79C Update #3: Another Lockup :-( Well, I had another lockup last night. :-( SpeedFan reported the CPU temp at 38 C when it happened, and there was no spike in temperature leading up to the freeze. One thing I notice is that the freeze seems more likely to happen if I am watching a video. In fact, of the last 5 freezes over the past month, 4 of them have been while watching a video on Flickr. Not necessarily the same video, but a video nevertheless. I don't know if this is just coincidence or if it means anything. (As an aside, each night before bedtime my 2 year old daughter sits on my lap and watches some home videos on Flickr and, in the last month, has learned the phrase, "Uh oh, computer broke.") Update #4: MemTest86 and 3DMark06 Test Results: Per suggestions in the comments, I ran the MemTest86 overnight and it cycled through the 8 GB of memory 5 times without error. I also ran the 3DMark06 test without a problem (see my scores at http://3dmark.com/3dm06/15163549). So... what now? :-) Any further suggestions on what to check? Is there some way to get a stack trace or something when the computer locks like that? Resolution I have never did figure out the particular problems, but based on the suggestions here and elsewhere, I'm presuming it was a motherboard issue. In any event, I recently upgraded my system, buying a new motherbeard, PSU, CPU, and RAM, and that new rig has been working splendidly the past several weeks. I am using the same graphic cards as in the old setup, so I think it's safe to reason that they weren't the cause of the problem.

    Read the article

  • SmartOS reboots spontaneously

    - by Alex
    I run a SmartOS system on a Hetzner EX4S (Intel Core i7-2600, 32G RAM, 2x3Tb SATA HDD). There are six virtual machines on the host: [root@10-bf-48-7f-e7-03 ~]# vmadm list UUID TYPE RAM STATE ALIAS d2223467-bbe5-4b81-a9d1-439e9a66d43f KVM 512 running xxxx1 5f36358f-68fa-4351-b66f-830484b9a6ee KVM 1024 running xxxx2 d570e9ac-9eac-4e4f-8fda-2b1d721c8358 OS 1024 running xxxx3 ef88979e-fb7f-460c-bf56-905755e0a399 KVM 1024 running xxxx4 d8e06def-c9c9-4d17-b975-47dd4836f962 KVM 4096 running xxxx5 4b06fe88-db6e-4cf3-aadd-e1006ada7188 KVM 9216 running xxxx5 [root@10-bf-48-7f-e7-03 ~]# The host reboots several times a week with no crash dump in /var/crash and no messages in the /var/adm/messages log. Basically /var/adm/messages looks like there was a hard reset: 2012-11-23T08:54:43.210625+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T09:14:43.187589+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T09:34:43.165100+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T09:54:43.142065+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T10:14:43.119365+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T10:34:43.096351+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T10:54:43.073821+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T10:57:55.610954+00:00 10-bf-48-7f-e7-03 genunix: [ID 540533 kern.notice] #015SunOS Release 5.11 Version joyent_20121018T224723Z 64-bit 2012-11-23T10:57:55.610962+00:00 10-bf-48-7f-e7-03 genunix: [ID 299592 kern.notice] Copyright (c) 2010-2012, Joyent Inc. All rights reserved. 2012-11-23T10:57:55.610967+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: lgpg 2012-11-23T10:57:55.610971+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: tsc 2012-11-23T10:57:55.610974+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: msr 2012-11-23T10:57:55.610978+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: mtrr 2012-11-23T10:57:55.610981+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: pge 2012-11-23T10:57:55.610984+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: de 2012-11-23T10:57:55.610987+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: cmov 2012-11-23T10:57:55.610995+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: mmx 2012-11-23T10:57:55.611000+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: mca 2012-11-23T10:57:55.611004+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: pae 2012-11-23T10:57:55.611008+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: cv8 The problem is that sometimes the host loses the network interface on reboot so we need to perform a manual hardware reset to bring it back. We do not have physical or virtual access to the server console - no KVM, no iLO or anything like this. So, the only way to debug is to analyze crash dumps/log files. I am not a SmartOS/Solaris expert so I am not sure how to proceed. Is there any equivalent of Linux netconsole for SmartOS? Can I just redirect the console output to the network port somehow? Maybe I am missing something obvious and crash information is located somewhere else.

    Read the article

  • /usr/bin/sshd isn't linked against PAM on one of my systems. What is wrong and how can I fix it?

    - by marc.riera
    Hi, I'm using AD as my user account server with ldap. Most of the servers run with UsePam yes except this one, it has lack of pam support on sshd. root@linserv9:~# ldd /usr/sbin/sshd linux-vdso.so.1 => (0x00007fff621fe000) libutil.so.1 => /lib/libutil.so.1 (0x00007fd759d0b000) libz.so.1 => /usr/lib/libz.so.1 (0x00007fd759af4000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007fd7598db000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007fd75955b000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x00007fd759323000) libc.so.6 => /lib/libc.so.6 (0x00007fd758fc1000) libdl.so.2 => /lib/libdl.so.2 (0x00007fd758dbd000) /lib64/ld-linux-x86-64.so.2 (0x00007fd759f0e000) I have this packages installed root@linserv9:~# dpkg -l|grep -E 'pam|ssh' ii denyhosts 2.6-2.1 an utility to help sys admins thwart ssh hac ii libpam-modules 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules for PAM ii libpam-runtime 0.99.7.1-5ubuntu6.1 Runtime support for the PAM library ii libpam-ssh 1.91.0-9.2 enable SSO behavior for ssh and pam ii libpam0g 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules library ii libpam0g-dev 0.99.7.1-5ubuntu6.1 Development files for PAM ii openssh-blacklist 0.1-1ubuntu0.8.04.1 list of blacklisted OpenSSH RSA and DSA keys ii openssh-client 1:4.7p1-8ubuntu1.2 secure shell client, an rlogin/rsh/rcp repla ii openssh-server 1:4.7p1-8ubuntu1.2 secure shell server, an rshd replacement ii quest-openssh 5.2p1_q13-1 Secure shell root@linserv9:~# What I'm doing wrong? thanks. Edit: root@linserv9:~# cat /etc/pam.d/sshd # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password Edit2: UsePAM yes fails With this configuration ssh fails to start : root@linserv9:/home/admmarc# cat /etc/ssh/sshd_config |grep -vE "^[ \t]*$|^#" Port 22 Protocol 2 ListenAddress 0.0.0.0 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys ChallengeResponseAuthentication yes UsePAM yes Subsystem sftp /usr/lib/sftp-server root@linserv9:/home/admmarc# The error it gives is as follows root@linserv9:/home/admmarc# /etc/init.d/ssh start * Starting OpenBSD Secure Shell server sshd /etc/ssh/sshd_config: line 75: Bad configuration option: UsePAM /etc/ssh/sshd_config: terminating, 1 bad configuration options ...fail! root@linserv9:/home/admmarc#

    Read the article

  • Asus P8P67 Rev. 3.1 Motherboard issues powering on and saving settings

    - by Scott
    Edit: New Information Have some updated information from the old question below: So basically my issue right now is somewhat similar, but I've been able to rule out a couple of things. I don't think this has anything to do with light on the motherboard. No matter what lights are on/off on the motherboard when the computer is off, they don't affect this issue. The main power LED on the Mobo is always lit when the power supply is turned on, and that's what matters anyway. Even when the main power LED is on, the PC will NOT boot up the first time I hit the power switch. I have to go reset the power supply (make all lights turn off on the Mobo and back on), and THEN hit the power switch. Then everything boots up. Also, the BIOS settings are reset every time this happens. Asus Tech Support told me to try jumping the power with something metal to try and rule out that it's a problem with the connectors getting power, or if it's a problem with the case power switch pins - haven't done that yet though. Any ideas? This is a lot simpler than it was before when I thought it had to do with certain LED indicators for RAM, EPU, etc. Original Question So I built my new desktop just about 3 weeks ago. I've been having a few issues which I think are all related to my motherboard, an Asus P8P67 Revision 3.1, but I'm not 100% sure as this is really the first from-scratch build I've ever done. I've posted these questions on the Asus forums, Asus Tech Support, and the Corsair forums as well as I thought it might have something to do with my power supply at one point. None of these avenues have solved my issue until now completely, so I thought I'd come here to see what you guys think. Here's what's happening: My computer is off, and I go to power it on. I press the power switch on the case (Antec Nine Hundred), and nothing seems to happen. Upon further inspection, I see that what this actually does is simply turn on the EPU LED on my motherboard, but doesn't actually boot anything up. I then have to go and flip the main power switch on the power supply off and back on. What this does is turn off all lights on the Motherboard after a few seconds, and turn them all back on (including the EPU LED that was off before I hit the power switch the first time). Now, hitting the power switch works. The machine boots up fine, and starts going through the boot up process. As a side note: My Motherboard is set to "Force BIOS", and every single time I change this to do the opposite, the next time my computer boots up that change reverts itself. I think this may be due to the fact that I am doing the hard reset on the power supply each time, but I'm not sure. I had thought that the Motherboard would keep its BIOS settings unless you did something to the Mobo itself - so this may be a related issue, or something else completely. That's basically it. Once it's on, it's on. It works fine, recognizes all of my hardware, and runs great. All fans/lights in the case work great, and I'm getting standard readings. The next time I go to shut the computer down however, I can expect the same exact process getting it up and running, including being forced to go into BIOS and exit again before I can load Windows. Another side note: If I power on my computer using the power switch DIRECTLY after shutting it down, it powers right back on (I think this is because the EPU LED light doesn't have time to turn off). It looks as if as long as the EPU LED is lit up on the motherboard before I hit the power switch on the case, the thing will boot up fine (although this doesn't explain the "Force BIOS" issue, at least it's something). Any ideas? Thanks guys. P.S. - System Specs Asus P8P67 Rev. 3.1 Motherboard Intel Core i7 2600K Processor 16GB (4x4GB) G-Skill 1600 RAM NVIDIA EVGA GTX 570 Video Card Crucial 128GB SSD HD Corsair 850W Power Supply Seagate 2TB HDD

    Read the article

  • Symantec Protection Suite and System Recovery 2011 Desktop Edition

    - by rihatum
    I am re-posting this as my previous question was being treated as if I am "Shopping or seeking Product Recommendations" even though I was NOT - BTW they have deleted my comments too which were not offensive in nature. anyway - I have re-phrased some parts of my question and I hope SF Admins "Do Not Modify / Edit" this one - will be most grateful for that. I have a lot of respect for the People who visit this SITE and help others ! Just To clarify : Just to go by SF rules - I am not seeking someone to Design this solution, I am simply seeking real world examples, experiences, technical expert opinions / suggestions, any tips or tricks they may have or any problems they may have faced while doing something similar above with these products. I am also not asking for Capacity Planning for Storage, We have done some research and I am seeking Expert Assurance / Suggestions. We (our company) are planning to deploy Symantec Endpoint Protection and Symantec Desktop Recovery 2011 Desktop Edition to our 3000 - 4000 workstations (Windows7 32 and 64) with a few 100s with Windows XP 32/64 Bit. I have read the implementation guide for SEP and have read tech-notes for Desktop Recovery 2011. Our team have planned to deploy this as follows : 1 x dedicated SQL 2008R2 for Symantec Endpoint Protection (Instead of using the Embedded Database) 1 x Dedicated SQL 2008R2 for Symantec Desktop Recovery 2011 (Instead of using the Embedded Database) 1 x Dedicated W2K8 R2 Box for the SEPM (Symantec Endpoint Protection Manager - Mgmt. APP) 1 x Dedicated W2K8 R2 Box for the Symantec Desktop Recovery 2011 Management Application Agent Deployment : As per Symantec Documentation for both of the above, an agent can be pushed via the Mgmt. Application (provided no firewalls are blocking ports required etc. - we have Windows firewall disabled already). Server Hardware : Per SQL Server : 16GB RAM + SAS DISKS + Dual XEON, RAID-10 for the SQL DB or I can always mount a LUN from our existing Hitachi or EMC SAN. SEPM Server : 16GB RAM + SAS DISKS + DUAL XEON System Recovery MGMT SERVER : 16GB RAM + SAS DISKS + DUAL XEON Above is the initial plan we have for 3000 - 4000 client workstation (Windows) Now my Questions :-) a) If we had these users distributed amongst two sites with AD DC / GC in each site, How would I restrict SEPM and Desktop Mgmt. solution to only check for users in their respective site ? b) At present all users are under one building but we are going to move some dept. to a new location (with dedicated connectivity), How would we control which SEPM / MGMT Server is responsible for which site ? c) We have netbackup in our environment backing up other servers, I am planning to protect these 4 (2 x SQL, 1 x SEPM, 1 x System Recovery Mgmt. Server) via netbackup or I can use System recovery 2011 server edition on all 4 of these boxes as well. (License is not an issue as we have the complete symantec portfolio included in our license). d) Now - Saving Desktop backups - What strategies have you implemented ? Any best practice recommendation for a large user base ? I was thinking to either mount a LUN from our Hitachi SAN on the Symantec Recovery Server itself or backup to the users hard drive locally and then copy it over to a network location ? Suggestions welcome :-) If you have anything to add / correct - that will be really helpful before diving into the actual implementation phase. Will be most grateful with your suggestions, recommendations and corrections with above - Many Thanks !

    Read the article

  • Where to download replacement "Explorerframe.DLL" Files for x64 Windows 7 Pro?

    - by Ben Franchuk
    After posting this question, I did some research to reveal what the problem likely was, and found what I need to fix. Following this is the original post, then my updated question. A few months ago I ended up requiring to change my computer's SID to fix a problem it had been having- Instead of fixing the problem, though, it screwed up my at-the-time current install of windows, to the point of me needing to do a fresh install. As I am in possession of an OEM copy of Windows 7 Pro 64 Bit, I successfully reinstalled over the dead copy with that (all the files that were on the computer previous to this windows install were put in a Windows.old folder). Everything installed and worked absolutely fine, except for one thing. The problem I am experiencing is that, in some Windows Explorer windows, the explorer pane doesn't show. Instead, it simply shows a white area where the pane would show. This makes some software not usable, I recently realized; Software such as Cubase, which use just the explorer pane to select file save locations, cannot save at all as the pane itself is... not operational. Below is a screenshot of this problem as it occurs in cubase; ...and again as it shows in UTorrent in the save location selector window. The highlighted area is where the sidebar would NORMALLY be. Pardon my scribbling over some of the things in the window- I would personally rather the internet did not get a glimpse of my files. I have yet to find a common reason why the pane works in some applications when they pull explorer, and others not. I have yet to see it go away, and the software affected by it has been affected since I reinstalled my copy of windows. Initially, I was able to live with it as I can type out save locations in the file name bar to navigate, but with software like Cubase, I do not have this option. Reinstalling windows again is NOT an option. Here's the updated question. After posting this question originally, I did some research on the problem in question, and it turns out that this is extremely easily fixable via replacing the file "ExplorerFrame.DLL" which is located in the System32 and SystemWOW64 Folders, in the windows folder, on the C:\ drive. As I quite frequently customize my computer, this is a normal thing for me to do and I know exactly how to safely and properly replace this file. The only problem is that I cannot for the life of me find a download of this file that actually works with my computer. I tried a couple from some different sites but they all caused explorer to not restart (I was given an error when starting the application from Task Manager) and was forced to revert to the broken .DLL files. Since there are 2 separate "ExplorerFrame.DLL" files; one for 64 bit and the other for 32 bit, I am assuming that I will need to download 2 separate versions to replace the corrupted ones. Where can I acquire these files? I am currently running Windows 7 Professional x64 Bit.

    Read the article

  • What NAS setup for two-way syncing over the internet?

    - by Jamse
    I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker. Update I've been digging some more and it looks like QNAP's Remote Replication function is actually just Rsync, so only really suitable for one-way syncing. I've posted on their forum to double check, but I think that's the case. In which case, I think the focus of my question is now either: do any reasonably-priced NASs support bidirectional syncing over the internet?, or has anyone had any luck installing onto NASs for this purpose? (Also, updated question to clarify that I'm after two-way syncing.)

    Read the article

  • Where's my memory?! Nginx + PHP-FPM front end webserver slows to a crawl...

    - by incredimike
    I'm not sure if I have a problem with a memory leak (as my hosting company suggests), or if we both need to read http://linuxatemyram.com. Maybe you clever people can help us out? This is a front-end webserver VM running essentially only nginx & php-fpm on RHEL 5.5. This server is powering Magento, a PHP eCommerce thinggy. The server is running in a shared environment, but we're changing that soon. Anyway.. after a reboot the server runs just fine, but within a day it will grind itself into nothingness. Pages will take literally 2 minutes to load, CPU spikes like crazy, etc.. The console is even sluggish when I SSH in. It's like my whole server is being brought to its knees. I've also been monitoring the DB server via top and tcpdumping incoming traffic. The DB stays idle for a good portion of that "slow" load time. When i start seeing queries coming from the front-end server, the page loads soon afterward. Here are some stats after me logging in during a slow-down, after restarting php-fpm: [mike@front01 ~]$ free -m total used free shared buffers cached Mem: 5963 5217 745 0 192 314 -/+ buffers/cache: 4711 1252 Swap: 4047 4 4042 [mike@front01 ~]$ top top - 11:38:55 up 2 days, 1:01, 3 users, load average: 0.06, 0.17, 0.21 Tasks: 131 total, 1 running, 130 sleeping, 0 stopped, 0 zombie Cpu0 : 0.0%us, 0.3%sy, 0.0%ni, 99.3%id, 0.3%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 0.3%us, 0.0%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 6106800k total, 5361288k used, 745512k free, 199960k buffers Swap: 4144728k total, 4976k used, 4139752k free, 328480k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31806 apache 15 0 601m 120m 37m S 0.0 2.0 0:22.23 php-fpm 31805 apache 15 0 549m 66m 31m S 0.0 1.1 0:14.54 php-fpm 31809 apache 16 0 547m 65m 32m S 0.0 1.1 0:12.84 php-fpm 32285 apache 15 0 546m 63m 33m S 0.0 1.1 0:09.22 php-fpm 32373 apache 15 0 546m 62m 32m S 0.0 1.1 0:09.66 php-fpm 31808 apache 16 0 543m 60m 35m S 0.0 1.0 0:18.93 php-fpm 31807 apache 16 0 533m 49m 30m S 0.0 0.8 0:08.93 php-fpm 32092 apache 15 0 535m 48m 27m S 0.0 0.8 0:06.67 php-fpm 4392 root 18 0 194m 10m 7184 S 0.0 0.2 0:06.96 cvd 4064 root 15 0 154m 8304 4220 S 0.0 0.1 3:55.57 snmpd 4394 root 15 0 119m 5660 2944 S 0.0 0.1 0:02.84 EvMgrC 31804 root 15 0 519m 5180 932 S 0.0 0.1 0:00.46 php-fpm 4138 ntp 15 0 23396 5032 3904 S 0.0 0.1 0:02.38 ntpd 643 nginx 15 0 95276 4408 1524 S 0.0 0.1 0:01.15 nginx 5131 root 16 0 90128 3340 2600 S 0.0 0.1 0:01.41 sshd 28467 root 15 0 90128 3340 2600 S 0.0 0.1 0:00.35 sshd 32602 root 16 0 90128 3332 2600 S 0.0 0.1 0:00.36 sshd 1614 root 16 0 90128 3308 2588 S 0.0 0.1 0:00.02 sshd 2817 root 5 -10 7216 3140 1724 S 0.0 0.1 0:03.80 iscsid 4161 root 15 0 66948 2340 800 S 0.0 0.0 0:10.35 sendmail 1617 nicole 17 0 53876 2000 1516 S 0.0 0.0 0:00.02 sftp-server ... Is there anything else I should be looking at, or any more information that might be useful? I'm just a developer, but the slowdowns on this system worry me and make it hard to do my work.. Help me out, ServerFault!

    Read the article

  • Amazon EC2 Instance - m1.medium Ubuntu 12.04 - Started to crash three days ago

    - by Joy
    The environment: Amazon EC2 Instance - m1.medium Ubuntu 12.04 Apache 2.2.22 - Running a Drupal Site Using MySQL DB Server RAM info: ~$ free -gt total used free shared buffers cached Mem: 3 1 2 0 0 0 -/+ buffers/cache: 0 2 Swap: 0 0 0 Total: 3 1 2 Hard drive info: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 4.7G 2.9G 62% / udev 1.9G 8.0K 1.9G 1% /dev tmpfs 751M 180K 750M 1% /run none 5.0M 0 5.0M 0% /run/lock none 1.9G 0 1.9G 0% /run/shm /dev/xvdb 394G 199M 374G 1% /mnt The problem About two days ago the site started failing becaue the MySQL server was shut down by Apache with the following message: kernel: [2963685.664359] [31716] 106 31716 226946 22748 0 0 0 mysqld kernel: [2963685.664730] Out of memory: Kill process 31716 (mysqld) score 23 or sacrifice child kernel: [2963685.664764] Killed process 31716 (mysqld) total-vm:907784kB, anon-rss:90992kB, file-rss:0kB kernel: [2963686.153608] init: mysql main process (31716) killed by KILL signal kernel: [2963686.169294] init: mysql main process ended, respawning That states that the VM was occupying 0.9GB, but my Ram has 2GB free, so 1GB was still left free. I understand that in Linux applications can allocate more memory than physically available. I don't know if this is the problme, it's the first time that it has started to happen. Obviously, the MySQL server tries to restart, but there's no memory for it apparently and it won't restart. Here is its error log: Plugin 'FEDERATED' is disabled. The InnoDB memory heap is disabled Mutexes and rw_locks use GCC atomic builtins Compressed tables use zlib 1.2.3.4 Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 Completed initialization of buffer pool Fatal error: cannot allocate memory for the buffer pool Plugin 'InnoDB' init function returned error. Plugin 'InnoDB' registration as a STORAGE ENGINE failed. Unknown/unsupported storage engine: InnoDB [ERROR] Aborting [Note] /usr/sbin/mysqld: Shutdown complete I simply restarted the Mysql service. About two hours later it happened again. I restarted it. Then it happened again 9 hours later. So then I thought of the MaxClients parameter of apache.conf, so I went to check it out. It was set at 150. I decided to drop it down to 60. As so: <IfModule mpm_prefork_module> ... MaxClients 60 </IfModule> <IfModule mpm_worker_module> ... MaxClients 60 </IfModule> <IfModule mpm_event_module> ... MaxClients 60 </IfModule> Once I did that, I had the apache2 service restart and it all went smoothly for 3/4 of a day. Since at night the MySQL service shut down once again, but this time it wasn't killed by the Apache2 service. Instead it called the OOM-Killer with the following message: kernel: [3104680.005312] mysqld invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0, oom_score_adj=0 kernel: [3104680.005351] [<ffffffff81119795>] oom_kill_process+0x85/0xb0 kernel: [3104680.548860] init: mysql main process (30821) killed by KILL signal Now I'm out of ideas. Some articles state that the ideal thing to do is change the kernel behaviour with the following (include it to the file /etc/sysctl.conf ) vm.overcommit_memory = 2 vm.overcommit_ratio = 80 So no overcommits will take place. I'm wondering if this is the way to go? Keep in mind I'm no server administrator, I have basic knowldege. Thanks a bunch in advance.

    Read the article

  • ISP 5 Device Limit ... again

    - by Tommo
    Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

    Read the article

  • USB connection is unstable with Nexus S 2.3.4 on AMD 64 running 64-bit Windows 7, but works with 32-bit Windows Vista

    - by Mike
    The USB connection is unstable with Nexus S (Android 2.3.4) on AMD 64 running 64-bit Windows 7, but it works with 32-bit Windows Vista. Problem Description: On the 64-bit Windows 7 machine my Nexus S appears to connect, but then it disconnects moments later. Neither accessing USB storage or loading an Android application package file (APK) using the Android Debug Bridge (ADB) work. On 32-bit Windows Vista using the same USB cable, USB storage works. I haven't tried the ADB on 32-bit Windows Vista. Reproduction steps for USB storage: (I have provided the reproduction steps for USB storage and not ADB, because if one isn't working, then the other isn't working either and the USB storage reproduction steps are shorter to document.) Connect the USB cable to the Nexus S and my Windows 7 machine. Effect: The "USB Mass Storage, USB Connected" dialog appears with the button "Turn on USB storage." Click "Turn on USB Storage" Effect: The "working circle" appears. A dialog briefly appears saying "USB storage in use," then it either returns me to Step 1 (now that I am running 2.3.4) or is replaced with the Nexus S's application homepage (while I was running 2.3.3). I'm not sure if the version matters, but I mention it for completeness. On the 32-bit Windows Vista machine the connection is stable. I am able to navigate through the Nexus S file system create, read, update, and delete files, etc. I haven't tried connecting with the ADB. Troubleshooting summary: Tried and failed: Uninstalling and reinstalling the Android USB drivers including removing the files. Uninstalling my custom software Pulling the Nexus S's battery Restarting the Nexus S Restarting 64-bit Windows 7 Changing USB ports on the 64-bit Windows 7 box Compared the dates and file size on the DLLs in my google-usb_driver\amd64 directory and the windows\System32 directory. They match. The sizes for the google-usb_driver\i386 directory do not match (expected). Turning off Debugging mode on the Nexus S does not resolve the problem. Searching Google. Tried and succeeded: Connecting to another machine (Windows Vista) using the same USB cable and Nexus S phone. Troubleshooting observations: I notice that uninstalling the device drivers and deleting the files, then reinstalling the drivers, then rebooting 64-bit Windows 7 then unplugging the Nexus S, then plugging it back in occasionally helps for a short amount of time (minutes to hours, not days). When it is working, I can both access the Nexus S's drive and load/test applications using the ADB. I have observed some wonky behavior in the Device Manager that I haven't tracked down. Sometimes the black Nexus S image appears in the list of devices. Sometimes the image displays as a computer with a green ISA card. Sometimes it neither appears on the top level of devices nor under “other devices,” but it does appear under "disk drives" as "Android UMS Composite USB Device." System configuration: The Nexus S is running Android OS 2.3.4's "Settings\about phone\System updates" indicates that it is up to date as of May 21st 2011. Both 32-bit Windows Vista and 64-bit Windows 7 are up to date. The Windows Vista system is running on an Intel 32-bit processor. Windows 7 is running on an AMD 64-bit processor. I have done Android development on both systems, but I usually develop on the 64-bit Windows 7 machine.

    Read the article

  • What NAS setup for syncing over the internet?

    - by Jamse
    I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker.

    Read the article

  • IPv6: Should I have private addresses?

    - by AlReece45
    Right now, we have a rack of servers. Every server right now has at least 2 IP addresses, one for the public interface, another for the private. The servers that have SSL websites on them have more IP addresses. We also have virtual servers, that are configured similarly. Private Network The private range is currently just used for backups and monitoring. Its a gigabit port, the interface usage does not usually get very high. There are other technologies we're considering using that would use this port: iSCSI (implementations usually recommends dedicating an interface to it, which would be yet another IP network), VPN to get access to the private range (something I'd rather avoid) dedicated database servers LDAP centralized configuration (like puppet) centralized logging We don't have any private addresses in our DNS records (only public addresses). For our servers to utilize the correct IP address for the right interface (and not hard code the IP address) probably requires setting up a private DNS server (So now we add 2 different dns entries to 2 different systems). Public Network Our public range has a variety of services include web, email, and ftp. There is a hardware firewall between our network and the "public" network. We have (relatively secure) method to instruct the firewall to open and close administrative access (web interfaces, ssh, etc) for our current IP address. With either solution discussed, the host-based firewalls will be configured as well. The public network currently runs at a dedicated 20Mbps link. There are a couple of legacy servers with fast-ethernet ports, but they are scheduled for decommissioning. All of the other production boxes have at least 2 Gigabit Ethernet ports. The more traffic-heavy servers have 4-6 available (none is using more than the 2 Gigabit ports right now). IPv6 I want to get an IPv6 prefix from our ISP. So at least every "server" has at least one IPv6 interface. We'll still need to keep the IPv4 addressees up and available for legacy clients (web servers and email at the very least). We have two IP networks right now. Adding the public IPv6 address would make it three. Just use IPv6? I'm thinking about just dumping the private IPv4 range and using the IPv6 range as the primary means of all communications. If an interface starts reaching its capacity, utilize the newly free interfaces to create a trunk. It has the advantage that if either the public or private traffic needs to exceed 1Gbps. The traffic for each interface is already analyzed on a regular basis to predict future bandwidth use. In the rare instances where bandwidth unexpected peaks: utilize QoS to ensure traffic (like our limited SSH access) is prioritized correctly so the problem can be corrected (if possible, our WAN is the bottleneck right now). It also has the advantage of not needing to make an entry for every private address. We may have private DNS (or just LDAP), but it'll be much more limited in scope with less entries to duplicate. Summary I'm trying to make this network as "simple" as possible. At the same time, I want to make sure its reliable, upgradeable, scalable, and (eventually) redundant. Having one IPv6 network, and a legacy IPv4 network seems to be the best solution to me. Regarding using assigned IPv6 addresses for both networks, sharing the available bandwidth on one (more trunked if needed): Are there any technical disadvantages (limitations, buffers, scalability)? Are there any other security considerations (asides from firewalls mentioned above) to consider? Are there regulations or other security requirements (like PCI-DSS) that this doesn't meet? Is there typical software for setting up a Linux network that doesn't have IPv6 support yet? (logging, ldap, puppet) Some other thing I didn't consider?

    Read the article

  • WNDR3700 Router + Cisco SG200-08 + LACP + Dual Uplink

    - by kobaltz
    Background I have a storage server that has several virtual machine images stored on them. I would store them locally, but I have limited space on my desktop (using SSD storage). I would like to increase the bandwidth between the desktop and the storage server by using two NICs on each computer. My original configuration allowed about 55MBps between the desktop and storage server. This storage server also has several TBs of documents, pictures, movies, vms, and ISO/programs. The storage server has 8 1.5TB hard drives in a RAID 10 configuration with a hardware RAID controller. The benchmarks on the RAID 10 are about 300MBps. Configuration In short, I am trying to bridge my switch and router. The switch is a small 8 port Cisco smart switch that supports 802.3ad LACP. I have two computers plugged into the switch, each with 2 Intel Gigabit NICs. The first computer is a Windows 7 machine that has the Intel ANS software installed. I have LACP configured with the computer and now show 3 NICs (2 Physical + 1 TEAM Virtual @ 2Gbps). It looks like this computer is configured correctly. I trunked the two ports that this computer is plugged into with the switch's web interface. The second computer is a homebrew storage box running debian. I also have the bonding enabled on this machine and the switch configured with LACP. Without having the WNDR3700 router in the picture yet, I am able to communicate between the Windows 7 machine and the debian box since they both have static IP addresses. With LACP enabled on both machines I am getting about 106-108MBps speeds. Issue I plug in a network cable from the switch into the router and enable DHCP on the desktop. I saw no need to have a static address on the desktop. My transfer rates are still from 106MBps-108MBps. While this is still a boost, I am trying to figure out how to get about 140-180MBps. I am thinking that I need to increase the bandwidth from the router to the switch. My switch allows 4 groups for port trunking. I plugged in a second network cable from the router to the switch. My question is, what is the proper way to fix this issue. Should I port trunk the two ports that are going from the switch to the router? Keep in mind that the router is a WNDR3700 and is unsure whether or not it supports LACP. I do have OpenWRT installed on the router, but it still wasn't clear in any documentation that I found if it supported 802.3ad LACP standards. I am also wondering if there needs to be anything changed within the Cisco settings. [Edit] - Corrected some numbers, wasn't really paying attention. It looks like the speeds though at least two NICs are bonded with LACP is still reaching the max bandwidth of one port. Is there a way to configure the switch so that I can increase this bandwidth? Also, on the storage server, I had a couple of extra NICs laying around and threw them on there as well. Another EDIT and More Findings I happened to look at the traffic of each individual NIC and think that I see the problem. I tested with a simple transfer for a 4GB file. I noticed that only one of the NICs was taking the load of the traffic. I then copied the file back to the Storage Server and noticed that the other NIC was sending out the traffic. I have 802.3ad LACP enabled on the two NICs and I see that it gets enabled dynamically on the switch's interface. Should I be using Static Link Aggregation?

    Read the article

  • Windows Media Player won't launch on Vista - how to repair or reinstall it?

    - by rpm1200
    My friend asked me to look at her Acer Aspire laptop with Vista Home Premium as it is no longer playing DVDs. I found that Windows Media Player would not launch. I found this thread, which contained a number of suggestions, none of which solved the problem. Here is what I tried: Tried running WMP via desktop shortcut, QuickLaunch bar or going to Program Files\Windows Media Player\wmplayer.exe. In all cases, wmplayer would launch then terminate immediately (verified through the Processes tab in Task Manager). Tried running wmplayer.exe as Administrator. The UAC dialog would come up, I'd approve, then wmplayer would launch and terminate immediately. Uninstalled all non-Microsoft media programs except RealPlayer, iTunes, QuickTime, Acer Arcade (the laptop owner uses all those apps). Tried running Program Files\Windows Media Player\setup_wm.exe as Administrator, it launched but said that a newer version of WMP was already installed. Deleted the "Windows Media" folder located under %userprofile%\appdata\local\Microsoft then tried starting WMP - wmplayer would launch and terminate immediately. Register wmp.dll by typing "regsvr32 wmp.dll" in an Administrator cmd window then tried starting WMP - wmplayer would launch and terminate immediately. Run "SFC /SCANFILE" in an Administrator cmd window - get an error message that it found invalid system files and could not fix them, so look at the log file cbs.log. The log file shows that there are broken files associated with Windows Sidebar (which the user does not use) but none relating to WMP. Log off to safe mode and run "SFC /SCANFILE" in an Administrator cmd window again - same results. Try to download and install XP WMP - the microsoft.com site recognizes the OS as Genuine and allows the download, but when I launch the installer it says the system is not Genuine. Clicking the link directs me back to IE where I can authenticate the system as Genuine. The installer still fails to recognize the system as Genuine. It is a Genuine Vista installation. Try to run this update (KB931621). The installer said it did not apply to the system. Set Windows Media Player as default in Program Access and Defaults. Same results. Tried running "for %a in (%systemroot%\system32\wm*.dll) do regsvr32 /s %a" in an Administrator cmd window - same results. Went to this Knowledge Base article (947541) and ran the Microsoft Fix It. The Fix It ran successfully, but WMP would still launch and terminate immediately. Multiple reboots in the process of doing all of these steps. After all this, looked in the Application and Security logs. No events pertaining to WMP were logged. The computer was preinstalled with Vista Home Premium and I have the Acer backup DVDs which will reimage the drive. I do not have Vista install DVDs. Reimaging the system is not an option. I'd also rather not restore the system to an earlier point unless it's absolutely necessary. What else can I do to repair or reinstall WMP?

    Read the article

  • Windows Media Player won't launch on Vista - how to repair or reinstall it?

    - by rpm1200
    My friend asked me to look at her Acer Aspire laptop with Vista Home Premium as it is no longer playing DVDs. I found that Windows Media Player would not launch. I found this thread, which contained a number of suggestions, none of which solved the problem. Here is what I tried: Tried running WMP via desktop shortcut, QuickLaunch bar or going to Program Files\Windows Media Player\wmplayer.exe. In all cases, wmplayer would launch then terminate immediately (verified through the Processes tab in Task Manager). Tried running wmplayer.exe as Administrator. The UAC dialog would come up, I'd approve, then wmplayer would launch and terminate immediately. Uninstalled all non-Microsoft media programs except RealPlayer, iTunes, QuickTime, Acer Arcade (the laptop owner uses all those apps). Tried running Program Files\Windows Media Player\setup_wm.exe as Administrator, it launched but said that a newer version of WMP was already installed. Deleted the "Windows Media" folder located under %userprofile%\appdata\local\Microsoft then tried starting WMP - wmplayer would launch and terminate immediately. Register wmp.dll by typing "regsvr32 wmp.dll" in an Administrator cmd window then tried starting WMP - wmplayer would launch and terminate immediately. Run "SFC /SCANFILE" in an Administrator cmd window - get an error message that it found invalid system files and could not fix them, so look at the log file cbs.log. The log file shows that there are broken files associated with Windows Sidebar (which the user does not use) but none relating to WMP. Log off to safe mode and run "SFC /SCANFILE" in an Administrator cmd window again - same results. Try to download and install XP WMP - the microsoft.com site recognizes the OS as Genuine and allows the download, but when I launch the installer it says the system is not Genuine. Clicking the link directs me back to IE where I can authenticate the system as Genuine. The installer still fails to recognize the system as Genuine. It is a Genuine Vista installation. Try to run this update (KB931621). The installer said it did not apply to the system. Set Windows Media Player as default in Program Access and Defaults. Same results. Tried running "for %a in (%systemroot%\system32\wm*.dll) do regsvr32 /s %a" in an Administrator cmd window - same results. Went to this Knowledge Base article (947541) and ran the Microsoft Fix It. The Fix It ran successfully, but WMP would still launch and terminate immediately. Multiple reboots in the process of doing all of these steps. After all this, looked in the Application and Security logs. No events pertaining to WMP were logged. The computer was preinstalled with Vista Home Premium and I have the Acer backup DVDs which will reimage the drive. I do not have Vista install DVDs. Reimaging the system is not an option. I'd also rather not restore the system to an earlier point unless it's absolutely necessary. What else can I do to repair or reinstall WMP?

    Read the article

  • How to install Delorme StreetAtlas (any version) + GPS inside VirtualBox VM?

    - by hotei
    When I try to run the install program I get a popup message that says the installer program is not a valid executable. Background: I want a GPS with maps on my laptop running Ubuntu 10.4LTS. Unfortunately I can't find a decent native Linux GPS solution with 50 state US street level coverage. I have VirtualBox VMs available for WinXP and Win7 (among others). The VMs work fine with MicroSoft Streets and Trips (2010) and MapNGo 5 (a very! old Delorme product), but while both these products support GPS, they don't support the Earthmate LT-40 USB GPS I already have. I've got pretty much every Delorme Street Atlas they've released in the last decade and none of them will install in a VM. Any help would be much appreciated. Clarification: I've installed the Delorme products from these CDs before and the disks are fine - as long as installation is done on a "physical" machine. Added: I've tried install from an iso as well as the real CD. No difference in result (setup.exe is not a valid executable) The WinXP is SP-2 (held back on purpose at this point - I'll snapshot and fork a later SP to test). The Win2K is SP-6a. Win7(32) VM is whatever updates came out last week. The USB setup is working at least to the point where the GPS device is active in the device list (has an x in the box). At this point its not relevant because the program that needs to read it can't even be installed. Added 9-19: Added wine as harrymc suggested. Initial result was no change. Here's wines error message. The file '/media/Disk1/setup.exe' is not marked as executable. If this was downloaded or copied form an untrusted source, it may be dangerous to run. For more details, read about the executable bit. At first I thought the execute bit was the problem, but looking at several other windows CDs I see that the execute bit is not set on their exe files (which install to VM without error). Still it was worth a shot so I copied the StreetAtlas 9 DVD to my hard disk, changed the on-disk exe files to have the execute bit set and tried to install again. This time the install via wine got me through the installation process. When I start the program it bombs immediately, so we haven't made much real progress so far. I very much prefer the VM solution to wine, so I'm going back to that for now. To recap the VM situation, using an updated XP with SP3 and all recommended hotfixes: StreetAtlas 2009 USA fails with "not marked as executable". StreetAtlas 2007 USA fails with "not marked as executable". StreetAtlas 9 (copyright 2001) fails with "not marked as executable". SteeetAtlas (copyright 1991) fails with "not marked as executable" Delorme Topo 4 (copyright 2002) fails with "not marked as executable". Just about ready to give up. So I switched from XP VM to Win7 VM and tried StreetAtlas 2009 again. This time it installs. Earthmate USB GPS works. WTH? I feel like the monkey who just wrote a line of Shakespear. I'm smiling because it worked, but I have no clue why. I'm awarding the bounty to harrymc because wine did give some useful insight into the problem and a +1 to goyiux as thanks for helping.

    Read the article

  • Gaming blew fuse and causes funny smell: how to overcome?

    - by George Tomlinson
    I've been gaming for a while now. When playing certain games this PC goes into overdrive. The fan/fans start/s to sound like a jet engine it/they get/s so busy. Also I have smelt burning when this has happened. The fuse blew on the 4 socket adapter I was using recently. On the following thread someone said this could be due to the PSU not being strong enough to handle the load, in what it seems could be a related issue someone had, although the person who posted this question did say that blowing a fan on their PC stopped it crashing in that case: http://www.tomshardware.co.uk/answers/id-2047543/gtx-650-overheating-issue.html. This is exactly what they said: Your GPU isn't overheating. 70+ before it would shutdown and cause a restart. Make sure your PSU is strong enough to handle your new system at load and possibly run Memtest to check your RAM (although not BSOD'ing and just shutting down points to the PSU). This (the PSU part) makes more sense to me than it being to do with dust etc, since it seems a more plausible explanation of why the fuse blew. The PC has no problems except when playing certain games: i.e. TERA Rising and WoW with add-ons (I think WoW is ok as long as I don't have more than 1 add-on (Healers Have To Die)). I'm just wondering if anyone knows or can suggest what I might be able to do to be able to play these games without this problem occurring. The PC's spec is this: Display: NVIDIA GeForce GTX 650 8GB RAM (6 available) Processor: AMD FX (tm) - 8120 Eight-Core Processor - 3.1 GHz, 4 Cores, 8 Logical Processors I have read on another post that forcing vsync in the Nvidia Control Panel helped with what seems could be a similar problem, so I plan to see if that solves it, God permitting. EDIT: I tried the Vsync thing, and it seems the situation may have improved, although this may be due to something else: i.e. maybe the PC was working harder yesterday, due to just having downloaded a few things or lots of things running. I'm still noticing the funny smell when playing TERA. It's not so much burning: it's more like glue. The smell might have had a burning element to it in the past, but I think it's always had a glue element. EDIT 2: the PSU is an 'ATX Switching Power Supply', Model E-500ATX. Other info it gives on the PSU is 230V, Current 10A and Frequency 50-60Hz. It also has some other info which I can supply if necessary. Putting the PC plug in the wall socket instead of the power strip seems like it might have reduced the load on the PC quite a bit: I think it sounds less stressed. it has been off for a while whilst I took the side panel off though, so I'll wait to see what happens before getting too excited. EDIT 3: hmm. So here's the latest: just playing TERA. The fan's running quite fast again. Hard to tell whether switching to the wall socket has made a difference in terms of strain on the PC: I don't know if one would expect it to. Still seems like it might have helped though. Oh and there didn't seem to be much dust in the PC, although I didn't disconnect any components. I'm still getting the glue type smell. ASIDE: reminds me of someone on a PC near me at the library once who was actually sniffing glue right there in front of everyone while on the PC and he started talking about how he was sniffing glue. lol. That's no joke. EDIT 4: So the questions now are: Question 1: Is the smell something I should sort out? (If so, how might I do this?) Question 2: is it necessary to take any steps to prevent blowing another fuse (and if so which step/s?).

    Read the article

< Previous Page | 741 742 743 744 745 746 747 748 749 750 751 752  | Next Page >