Search Results

Search found 32568 results on 1303 pages for 'linux pwns mac'.

Page 754/1303 | < Previous Page | 750 751 752 753 754 755 756 757 758 759 760 761  | Next Page >

• Installing grub2 on ubuntu with software raid mirroring

  - by Marko

  Can someone help me out on this? I accidentally installed grub on usb flash drive during ubuntu server installation. Now I cant boot system without drive attached to server. I want to install grub on hard drive with grub-install but i don't know what to set as location for boot loader? my fstab looks like this: file system mount point type options dump pass proc /proc proc nodev,noexec,nosuid 0 0 /dev/mapper/pdc_jdbeghhjg1 / ext4 errors=remount-ro 0 1 /dev/mapper/pdc_jdbeghhjg5 none swap sw 0 0 and partition tables for hard drives as this: Device Boot Start End Blocks Id System /dev/sda1 2048 1215662079 607830016 83 Linux /dev/sda2 1215664126 1249998847 17167361 5 Extended /dev/sda5 1215664128 1249998847 17167360 82 Linux swap / Solaris Device Boot Start End Blocks Id System /dev/sdb1 1 75672 607830016 83 Linux /dev/sdb2 75672 77809 17167361 5 Extended /dev/sdb5 75672 77809 17167360 82 Linux swap / Solaris ?

  Read the article

• Logging communication between two VMs

  - by sYnfo

  Hi, I'm trying to set up "malware lab" described in this paper. So far, I've set up Windows guest system, adding one Host-only Network adapter, and setting this (sorry if the names aren't exactely correct, I don't have an english language version): - IP Address - 10.0.0.3 - Subnet mask - 255.255.255.0 - Default gateway - not set - Preferred DNS - 10.0.0.4 - Alternate DNS - not set And a Linux guest system - Ubuntu 9.04 - with two Network adapters - Bridged (eth0) and Host-only (eth1), and setting eth1 IP Address to 10.0.0.4, leaving the eth0 to be set by DHCP. Then, I have configured iptables as described in the paper, ie.: iptables -F -t nat iptables -F -t mangle iptables -t mangle -P PREROUTING ACCEPT iptables -t mangle -P OUTPUT ACCEPT iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -t nat -P OUTPUT ACCEPT iptables -t mangle -A PREROUTING -i eth0 -j ACCEPT iptables -t mangle -A PREROUTING -p udp -i eth1 -d 10.0.0.3 --dport 53 -j ACCEPT iptables -t mangle -A PREROUTING -p tcp -i eth1 --dport 80 -j ACCEPT iptables -t mangle -A PREROUTING -p tcp -i eth1 -d 10.0.0.3 --dport 6000:7000 -j ACCEPT iptables -t mangle -A PREROUTING -i eth1 -j ULOG iptables -t mangle -A PREROUTING -i eth1 -j DROP Now, when I try to ping the windows system from within the Linux system, it does not reply, I guess thats perfectly normal, because iptables is blocking ping responce. Same when I try to ping the Linux system from within the Windows. But when I try to access any web page from within the Windows system, I would expect that this action should get logged by iptables. But thing is, I don't see any of that kind of lines in log file (If I am looking in the right place, that is. :) It is at /var/log/messages, isn't it?). So, what do you think might be the problem here? I should note, that this is the first time I'm using linux, so don't expect ANY working knowledge of Linux at all... :) Also, since english is not my mother tongue, feel free to point out any gramatical mistakes... :) Thanks for any advice.

  Read the article

• how to solve this problem

  - by Surbir

  root@me-desktop:~# sudo apt-get install aircrack-ng Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: aircrack-ng 0 upgraded, 1 newly installed, 0 to remove and 446 not upgraded. 1 not fully installed or removed. Need to get 1,579kB of archives. After this operation, 2,843kB of additional disk space will be used. Get:1 http://archive.ubuntu.com/ubuntu/ maverick/universe aircrack-ng i386 1:1.1-1 [1,579kB] Fetched 1,579kB in 1min 9s (22.7kB/s) Selecting previously deselected package aircrack-ng. (Reading database ... 520739 files and directories currently installed.) Unpacking aircrack-ng (from .../aircrack-ng_1%3a1.1-1_i386.deb) ... Processing triggers for man-db ... Setting up linux-image-3.0.1-030001-generic (3.0.1-030001.201108060905) ... Running depmod. update-initramfs: Generating /boot/initrd.img-3.0.1-030001-generic Warning: No support for locale: en_US.utf8 Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 3.0.1-030001-generic /boot/vmlinuz-3.0.1-030001-generic run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.0.1-030001-generic /boot/vmlinuz-3.0.1-030001-generic run-parts: executing /etc/kernel/postinst.d/nvidia-common 3.0.1-030001-generic /boot/vmlinuz-3.0.1-030001-generic run-parts: executing /etc/kernel/postinst.d/pm-utils 3.0.1-030001-generic /boot/vmlinuz-3.0.1-030001-generic run-parts: executing /etc/kernel/postinst.d/update-notifier 3.0.1-030001-generic /boot/vmlinuz-3.0.1-030001-generic run-parts: executing /etc/kernel/postinst.d/zz-update-grub 3.0.1-030001-generic /boot/vmlinuz-3.0.1-030001-generic exec: 15: update-grub: not found run-parts: /etc/kernel/postinst.d/zz-update-grub exited with return code 2 Failed to process /etc/kernel/postinst.d at /var/lib/dpkg/info/linux-image-3.0.1-030001-generic.postinst line 1010. dpkg: error processing linux-image-3.0.1-030001-generic (--configure): subprocess installed post-installation script returned error exit status 2 Setting up aircrack-ng (1:1.1-1) ... Errors were encountered while processing: linux-image-3.0.1-030001-generic E: Sub-process /usr/bin/dpkg returned an error code (1) root@me-desktop:~#

  Read the article

• Cannot install Nvidia driver X server

  - by Negoti Leboti

  I downloaded NVIDIA-Linux-x86-295.59.run from the official Nvidia website, I used in the terminal sudo sh NVIDIA-Linux-x86-295.59.run the installation started and everything, but I got this ERROR: You appear to be running an X server; please exit X before installing. For further details, please see the section INSTALLING THE NVIDIA DRIVER in the README available on the Linux driver download page at www.nvidia.com. I'm a newbie to ubuntu, and I don't know so much codes, can you please tell me step by step?

  Read the article

• How do I configure Ubuntu Server as Primary Domain Controller for Windows 7

  - by B. C.

  I have a Mac server running OS X Server 10.5 Server and as a PDC for our Windows XP systems. I'd like to use the OS X Server as a PDC for our Windows 7 boxes but the version of Samba in OS X Server is not compatible with Windows 7. It appears that my best bet is to use Ubuntu Server as my PDC. I want the Windows boxes to obtain authentication information from the Mac Server's LDAP. Any suggestions are appreciated.

  Read the article

• Access from one VM to an Other

  - by meo

  I got a Linux VM Image from a dev in our company to develop on it. This works nice, but now i need to do some Internet Explorer testing, for that i have an other VM with windows on it. I have an entry in my hosts file under macos that redirect some virtual domain to the IP of the linux VM. I tried to modify the hosts file in windows also. But i cant reach Linux VM. How can i access the Server on the linux VM with Windows VM? Are there some settings i missed?

  Read the article

• why Ubuntu 12.04.1 nautilus left panel, doesn't show other partitions and usb drives?

  - by amerllica

  how do you do friends will be fine I had Ubuntu 12.04 and all thing work well but at one day i decide to change my partition tables, and done it. at now I've windows 8, Ubuntu 12.04.1 and Backtrack5 R3 on my laptop. my partitions are: /dev/sda1 * 2048 58597375 29297664 7 HPFS/NTFS/exFAT /dev/sda2 58601472 976773119 459085824 5 Extended /dev/sda5 58605120 797020159 369207520 7 HPFS/NTFS/exFAT /dev/sda6 797030400 933763071 68366336 83 Linux /dev/sda7 933765120 972834815 19534848 83 Linux /dev/sda8 972836864 976773119 1968128 82 Linux swap / Solaris at first I install windows 8 and then Backtrack5 R3, and at last I install Ubuntu 12.04.1 and I realize that my Ubuntu nautilus doesn't show other partitions or usb/cd/dvd drives. I search in Google and various Linux or Ubuntu forums, But I can't find any solution, just one thing... that is "gvfs-gdu-volume" cause nautilus left panel show other partitions which didn't mounted. but when I see top there isn't this program. who can I solve this problem? how nautilus can show other partitions or drives in its left panel once again?

  Read the article

• Should I be running VM's(Virtual Box) for development on the same hdd as my os or a external usb (2.0) HDD or usb (2.0) flash drive

  - by J. Brown

  I have a mac book pro (7200 rpm / 8GB ram) and I like the idea of virtualized development environments as I like to experiment with different technologies and don't like to have environmental cross contamination. I would like to know for the vm's I run (rarely 2 at time..almost always 1 vm at a time) should the virtual hdd be on my laptops native hdd or some external form (usb hdd, usb flash, or since i have mac express card based sad ?). I don't mind maxing out my ram to 16GB if thats a better option to have in the mix. Thank you

  Read the article

• Fusion Middleware 11gR1 : 6??????

  - by Hiroyuki Yoshino

  2010?6??Fusion Middleware 11gR1 ?????????????? ?????????????3??????? 1. Oracle Enterprise Single Sign-On ?????Microsoft Windows (32-bit), Microsoft Windows x64 ???????????????? 10g?????????????????????????????????????Logon Manager?64-bit???????????? ????·????????????????????????·????????Non Oracle LDAP Certification?????????????? 2. Oracle Tuxedo Oracle Tuxedo 11g???????????? 10g???Oracle Tuxedo System and Application Monitor (TSAM), Oracle Service Architecture Leveraging Tuxedo (SALT)??????????? ??????AIX on Power Systems, HP-UX Itanium, Linux x86, Linux x86-64, Microsoft Windows (32-bit), Microsoft Windows x64, Solaris SPARC (64-bit), Other Platforms ?????????????????????????????????? ????·?????????????????Oracle Tuxedo ? Platform Data Sheets, TSAM ? Supported Platforms, SALT ? Supported Platforms ?????????? 3. Application Adapters ???Mainframe Adapters, CDC Adapters????Application Adapters?11g????????????? JD Edwards, PeopleSoft, SAP, Siebel ??????????????????? ??????AIX on Power Systems, HP-UX Itanium, HP-UX PA-RISC, Linux x86, Linux x86-64, Microsoft Windows (32-bit), Microsoft Windows x64, Solaris SPARC (64-bit) ??????????????? ??????(??????????????????)????????·????????Adapter Certification?????????????? ????? ????????(Media Pack)??????????????(Media Pack)????????????????? (2010?6??????????????????????)

  Read the article

• Update information outdated

  - by Achim Krause

  I have a warning triangle that my update information is outdated, the last update was 12 days ago. I use Ubuntu 11.10. A run of sudo apt-get update produces the following output: Ign http://ppa.launchpad.net oneiric InRelease Ign http://de.archive.ubuntu.com oneiric InRelease Ign http://de.archive.ubuntu.com oneiric-updates InRelease Ign http://de.archive.ubuntu.com oneiric-backports InRelease Ign http://security.ubuntu.com oneiric-security InRelease Ign http://extras.ubuntu.com oneiric InRelease Hit http://ppa.launchpad.net oneiric Release.gpg Get:1 http://de.archive.ubuntu.com oneiric Release.gpg [198 B] Hit http://security.ubuntu.com oneiric-security Release.gpg Get:2 http://extras.ubuntu.com oneiric Release.gpg [72 B] Hit http://ppa.launchpad.net oneiric Release Hit http://de.archive.ubuntu.com oneiric-updates Release.gpg Hit http://security.ubuntu.com oneiric-security Release Hit http://extras.ubuntu.com oneiric Release Err http://extras.ubuntu.com oneiric Release Hit http://ppa.launchpad.net oneiric/main Sources Hit http://de.archive.ubuntu.com oneiric-backports Release.gpg Hit http://security.ubuntu.com oneiric-security/main Sources Hit http://ppa.launchpad.net oneiric/main i386 Packages Ign http://ppa.launchpad.net oneiric/main TranslationIndex Ign http://linux.dropbox.com oneiric InRelease Hit http://security.ubuntu.com oneiric-security/restricted Sources Hit http://security.ubuntu.com oneiric-security/universe Sources Hit http://security.ubuntu.com oneiric-security/multiverse Sources Hit http://security.ubuntu.com oneiric-security/main i386 Packages Hit http://security.ubuntu.com oneiric-security/restricted i386 Packages Hit http://security.ubuntu.com oneiric-security/universe i386 Packages Hit http://security.ubuntu.com oneiric-security/multiverse i386 Packages Hit http://security.ubuntu.com oneiric-security/main TranslationIndex Hit http://security.ubuntu.com oneiric-security/multiverse TranslationIndex Hit http://security.ubuntu.com oneiric-security/restricted TranslationIndex Hit http://security.ubuntu.com oneiric-security/universe TranslationIndex Hit http://de.archive.ubuntu.com oneiric Release Hit http://de.archive.ubuntu.com oneiric-updates Release Ign http://de.archive.ubuntu.com oneiric Release Hit http://security.ubuntu.com oneiric-security/main Translation-en Hit http://security.ubuntu.com oneiric-security/multiverse Translation-en Hit http://linux.dropbox.com oneiric Release.gpg Hit http://security.ubuntu.com oneiric-security/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-backports Release Hit http://security.ubuntu.com oneiric-security/universe Translation-en Ign http://de.archive.ubuntu.com oneiric/main Sources/DiffIndex Ign http://de.archive.ubuntu.com oneiric/restricted Sources/DiffIndex Ign http://de.archive.ubuntu.com oneiric/universe Sources/DiffIndex Ign http://de.archive.ubuntu.com oneiric/multiverse Sources/DiffIndex Ign http://de.archive.ubuntu.com oneiric/main i386 Packages/DiffIndex Ign http://de.archive.ubuntu.com oneiric/restricted i386 Packages/DiffIndex Ign http://de.archive.ubuntu.com oneiric/universe i386 Packages/DiffIndex Ign http://de.archive.ubuntu.com oneiric/multiverse i386 Packages/DiffIndex Hit http://linux.dropbox.com oneiric Release Get:3 http://de.archive.ubuntu.com oneiric/main TranslationIndex [3,289 B] Get:4 http://de.archive.ubuntu.com oneiric/multiverse TranslationIndex [2,265 B] Hit http://de.archive.ubuntu.com oneiric/restricted TranslationIndex Get:5 http://de.archive.ubuntu.com oneiric/universe TranslationIndex [2,640 B] Hit http://de.archive.ubuntu.com oneiric-updates/restricted i386 Packages Hit http://de.archive.ubuntu.com oneiric-updates/universe i386 Packages Hit http://de.archive.ubuntu.com oneiric-updates/multiverse i386 Packages Hit http://de.archive.ubuntu.com oneiric-updates/main TranslationIndex Hit http://de.archive.ubuntu.com oneiric-updates/multiverse TranslationIndex Hit http://de.archive.ubuntu.com oneiric-updates/restricted TranslationIndex Hit http://de.archive.ubuntu.com oneiric-updates/universe TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/main Sources Hit http://linux.dropbox.com oneiric/main i386 Packages Ign http://ppa.launchpad.net oneiric/main Translation-en_US Ign http://ppa.launchpad.net oneiric/main Translation-en Ign http://linux.dropbox.com oneiric/main TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/restricted Sources Hit http://de.archive.ubuntu.com oneiric-backports/universe Sources Hit http://de.archive.ubuntu.com oneiric-backports/multiverse Sources Hit http://de.archive.ubuntu.com oneiric-backports/main i386 Packages Hit http://de.archive.ubuntu.com oneiric-backports/restricted i386 Packages Hit http://de.archive.ubuntu.com oneiric-backports/universe i386 Packages Hit http://de.archive.ubuntu.com oneiric-backports/multiverse i386 Packages Hit http://de.archive.ubuntu.com oneiric-backports/main TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/multiverse TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/restricted TranslationIndex Hit http://de.archive.ubuntu.com oneiric-backports/universe TranslationIndex Hit http://de.archive.ubuntu.com oneiric/main Sources Hit http://de.archive.ubuntu.com oneiric/restricted Sources Hit http://de.archive.ubuntu.com oneiric/universe Sources Hit http://de.archive.ubuntu.com oneiric/multiverse Sources Hit http://de.archive.ubuntu.com oneiric/main i386 Packages Hit http://de.archive.ubuntu.com oneiric/restricted i386 Packages Hit http://de.archive.ubuntu.com oneiric/universe i386 Packages Hit http://de.archive.ubuntu.com oneiric/multiverse i386 Packages Hit http://de.archive.ubuntu.com oneiric/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-updates/main Translation-en Hit http://de.archive.ubuntu.com oneiric-updates/multiverse Translation-en Hit http://de.archive.ubuntu.com oneiric-updates/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-updates/universe Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/main Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/multiverse Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/universe Translation-en Err http://de.archive.ubuntu.com oneiric-updates/main Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Err http://de.archive.ubuntu.com oneiric-updates/restricted Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Err http://de.archive.ubuntu.com oneiric-updates/universe Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Err http://de.archive.ubuntu.com oneiric-updates/multiverse Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Err http://de.archive.ubuntu.com oneiric-updates/main i386 Packages 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] Ign http://linux.dropbox.com oneiric/main Translation-en_US Ign http://linux.dropbox.com oneiric/main Translation-en Fetched 273 B in 2s (91 B/s) Reading package lists... Done W: A error occurred during the signature verification. The repository is not updated and the previous index files will be used. GPG error: http://extras.ubuntu.com oneiric Release: The following signatures were invalid: BADSIG 16126D3A3E5C1192 Ubuntu Extras Archive Automatic Signing Key <[email protected]> W: GPG error: http://de.archive.ubuntu.com oneiric Release: The following signatures were invalid: BADSIG 40976EAF437D05B5 Ubuntu Archive Automatic Signing Key <[email protected]> W: Failed to fetch http://extras.ubuntu.com/ubuntu/dists/oneiric/Release W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric/main/i18n/Index No Hash entry in Release file /var/lib/apt/lists/partial/de.archive.ubuntu.com_ubuntu_dists_oneiric_main_i18n_Index W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric/multiverse/i18n/Index No Hash entry in Release file /var/lib/apt/lists/partial/de.archive.ubuntu.com_ubuntu_dists_oneiric_multiverse_i18n_Index W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric/universe/i18n/Index No Hash entry in Release file /var/lib/apt/lists/partial/de.archive.ubuntu.com_ubuntu_dists_oneiric_universe_i18n_Index W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/main/source/Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/restricted/source/Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/universe/source/Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/multiverse/source/Sources 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric-updates/main/binary-i386/Packages 416 Requested Range Not Satisfiable [IP: 141.30.13.30 80] W: Some index files failed to download. They have been ignored, or old ones used instead. There are some questions with similar problems, but no one seems to get these "Range Not Satisfiable" errors. I do not use a proxy, and the network configuration should not have changed since it worked the last time.

  Read the article

• External usb 3.0 hard drive is not recognised when plugged into usb 3 port (ubuntu natty 64 bit).

  - by kimangroo

  I have an Iomega Prestige Portable External Hard Drive 1TB USB 3.0. It works fine on windows 7 as a usb 3.0 drive. It isn't detected on ubuntu natty 64bit, 2.6.38-8-generic. fdisk -l cannot see it at all: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1bed746b Device Boot Start End Blocks Id System /dev/sda1 1 1689 13560832 27 Unknown /dev/sda2 * 1689 1702 102400 7 HPFS/NTFS /dev/sda3 1702 19978 146805760 7 HPFS/NTFS /dev/sda4 19978 60802 327914497 5 Extended /dev/sda5 25555 60802 283120640 7 HPFS/NTFS /dev/sda6 19978 23909 31571968 83 Linux /dev/sda7 23909 25555 13218816 82 Linux swap / Solaris Partition table entries are not in disk order lsusb can see it: Bus 003 Device 003: ID 059b:0070 Iomega Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 004: ID 05fe:0011 Chic Technology Corp. Browser Mouse Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 0489:e00f Foxconn / Hon Hai Bus 001 Device 004: ID 0c45:64b5 Microdia Bus 001 Device 003: ID 08ff:168f AuthenTec, Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And dmesg | grep -i xhci (I may have unplugged the drive and plugged it back in again after booting): [ 1.659060] pci 0000:04:00.0: xHCI HW did not halt within 2000 usec status = 0x0 [ 11.484971] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 11.484997] xhci_hcd 0000:04:00.0: setting latency timer to 64 [ 11.485002] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 11.485064] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 11.636149] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 [ 11.636241] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X [ 11.636246] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X [ 11.636251] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X [ 11.636256] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X [ 11.636261] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X [ 11.639654] xHCI xhci_add_endpoint called for root hub [ 11.639655] xHCI xhci_check_bandwidth called for root hub [ 11.956366] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 2 [ 12.001073] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.007059] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.012932] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.018922] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.049139] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.056754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.131607] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 12.179717] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.686876] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 12.687058] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 12.687152] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 43.330737] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 2 [ 43.422579] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 43.422658] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af00 [ 43.422665] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af40 [ 43.422671] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af80 [ 43.422677] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669afc0 [ 43.531159] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 125.160248] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.766466] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 3 [ 903.807789] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.813530] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.819400] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.825104] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.855067] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862314] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862597] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.913211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 904.424416] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 904.424599] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 904.424700] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 935.139021] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 3 [ 935.226075] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 935.226140] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b00 [ 935.226148] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b40 [ 935.226153] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b80 [ 935.226159] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186bc0 [ 935.343339] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst I thought it might be that the firmware wasn't compatible with linux or something, but when booting a live image of partedmagic, (2.6.38.4-pmagic), the drive was detected fine, I could mount it and got usb 3.0 speeds (at least they double the speeds I got from plugging same drive in usb 2 ports). dmesg in partedmagic did say something about no SuperSpeed endpoint which was an error I saw in a previous dmesg of ubuntu: Jun 27 15:49:02 (none) user.info kernel: [ 2.978743] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jun 27 15:49:02 (none) user.debug kernel: [ 2.978771] xhci_hcd 0000:04:00.0: setting latency timer to 64 Jun 27 15:49:02 (none) user.info kernel: [ 2.978781] xhci_hcd 0000:04:00.0: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 2.978856] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 Jun 27 15:49:02 (none) user.info kernel: [ 3.089458] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 Jun 27 15:49:02 (none) user.debug kernel: [ 3.089541] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089544] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089546] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089548] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089550] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X Jun 27 15:49:02 (none) user.warn kernel: [ 3.092857] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values Jun 27 15:49:02 (none) user.info kernel: [ 3.092864] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 Jun 27 15:49:02 (none) user.info kernel: [ 3.092866] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Jun 27 15:49:02 (none) user.info kernel: [ 3.092867] usb usb3: Product: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 3.092869] usb usb3: Manufacturer: Linux 2.6.38.4-pmagic xhci_hcd Jun 27 15:49:02 (none) user.info kernel: [ 3.092870] usb usb3: SerialNumber: 0000:04:00.0 Jun 27 15:49:02 (none) user.debug kernel: [ 3.092961] xHCI xhci_add_endpoint called for root hub Jun 27 15:49:02 (none) user.debug kernel: [ 3.092963] xHCI xhci_check_bandwidth called for root hub Well I have no idea what's going wrong, and I haven't had much luck from google and the forums so far. A number of unanswered threads with people with similar error messages and problems only. Hopefully someone here can help or point me in the right direction?!

  Read the article

• Incoming traceroute blocked by ufw

  - by Tobias Timpe

  One of my Proxmox VMs running Ubuntu 13.04 won't accept incoming trace routes while ufw is enabled. What command do give ufw to allow incoming traceroute(6)s? The following shows up in the syslog with ufw enabled: 50:15:15:aa:ae:8d:7d:e4:7a:97:08:00 SRC=79.236.233.97 DST=78.46.101.252 LEN=52 TOS=0x00 PREC=0x00 TTL=1 ID=33400 PROTO=UDP SPT=63757 DPT=33466 LEN=32 Nov 4 16:20:36 web kernel: [8078158.260409] [UFW BLOCK] IN=eth0 OUT= MAC=00:50:56:15:15:aa:ae:8d:7d:e4:7a:97:08:00 SRC=79.236.233.97 DST=78.46.101.252 LEN=52 TOS=0x00 PREC=0x00 TTL=1 ID=33401 PROTO=UDP SPT=63757 DPT=33467 LEN=32 Nov 4 16:20:41 web kernel: [8078163.262626] [UFW BLOCK] IN=eth0 OUT= MAC=00:50:56:15:15:aa:ae:8d:7d:e4:7a:97:08:00 SRC=79.236.233.97 DST=78.46.101.252 LEN=52 TOS=0x00 PREC=0x00 TTL=2 ID=33402 PROTO=UDP SPT=63757 DPT=33468 LEN=32 Nov 4 16:20:46 web kernel: [8078168.262927] [UFW BLOCK] IN=eth0 OUT= MAC=00:50:56:15:15:aa:ae:8d:7d:e4:7a:97:08:00 SRC=79.236.233.97 DST=78.46.101.252 LEN=52 TOS=0x00 PREC=0x00 TTL=2 ID=33403 PROTO=UDP SPT=63757 DPT=33469 LEN=32 Nov 4 16:20:51 web kernel: [8078173.260521] [UFW BLOCK] IN=eth0 OUT= MAC=00:50:56:15:15:aa:ae:8d:7d:e4:7a:97:08:00 SRC=79.236.233.97 DST=78.46.101.252 LEN=52 TOS=0x00 PREC=0x00 TTL=2 ID=33404 PROTO=UDP SPT=63757 DPT=33470 LEN=32 And the trace route just ends in starts after the Proxmox host machine. Thanks Tobias Timpe

  Read the article

• KVM recommendations

  - by alex

  I recently tried out a cheaper KVM solution, a dual monitor one with a USB hub and audio/mic support. It seemed the perfect KVM. However, these are my experiences. When using my keyboard via the PS/2 connection, none of my multimedia keys work (useful, because it has a volume control and my speakers do not, only on a wireless remote control.) I plugged the keyboard in via the USB port - and it seemed to work. However, I believe to switch the hub from PC to Mac, you need to use a keyboard combo, which is only supported when the keyboard is plugged in via PS/2 Sometimes the middle mouse button doesn't work when connected via PS/2. The multi monitor is VGA - I just found out by the looks of things my Mac Mini outputs DVI Digital only (though this is my fault!). Mac works with 2 screens, but switching and switching back can cause it not to display on the 2nd screen unless I go detect displays again. My question is - is there a KVM out there that supports these features? USB keyboard and mouse inputs will full multimedia keys support Dual monitor DVI connections Hotkey to change PCs and physical button USB hub Emulate screens attached when switching to a different computer Works with PC and Mac Audio / Microphone support Does one exist, that won't cost the world? So far the only one that seems to support all this (that I can tell) is this one. UPDATE I ended up buying the Aten CS1642. It's expensive, but it seems to work great!

  Read the article

• One host on a network can't connect to one other host

  - by Max Williams

  I'm on a local network with a few other people. On of the hosts is a virtual machine running in virtualbox on a mac, which has the ip address 192.168.0.35 (the VM that is, not the mac host). Everyone except one guy can connect (ie ping, ssh etc) to that machine. When that one guy tries to ping it he gets Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 which i understand is just how certain mac os's report an unreachable connection. He can ping all the other hosts on the network, ie our computers, and we can all ping the VM fine and connect to it with no problems etc. His ip is 192.168.0.17. I ssh'd onto his machine (as a new user 'anon') and saw the same problems. I can ssh onto the 192.168.0.35 VM as well. From there, i can ping other users, but when i ping the problem guy, it's unreachable that way round as well. He restarted his mac, and was fine for a while. Then, just stopped working again. He's got a different IP to before. Any ideas, anyone? Don't know enough about this stuff to even diagnose the problem. thanks, max

  Read the article

• Synergy on macbook with osx mavericks wifi connection

  - by user332956

  I'm trying to set up Synergy with my macbook pro running OS X 10.9.3 as a client and my Windows 7 desktop as a server. I'm having some pretty bad connection problems though when I try to use my mac. Every couple seconds the mouse or the keyboard will stop working entirely then come back. I ran some tests and found that the ping from my desktop to my mac would be very high every third ping or so(1000+ ms) or sometimes even time out. If I ping my desktop from my mac the pings are all reasonably low. I believe that this is a power saving feature of Mavericks and I have found a way to get around it by continually pinging my router on my mac, keeping my wifi card from going to sleep. I'm using this right now to type this up with synergy and have had zero issues. Has anyone else ran into this issue and found a better solution? So far, I think my best bet would be to buy an ethernet adapter but I'd rather not have yet another cable running across my desk.

  Read the article

• OS X Client & Ubuntu Server - Best way for client to access files on server?

  - by Camsoft

  I've got a local development web server running Ubuntu. I also have an iMac running OS X 10.6 which I use a client and is my development machine. I'm currently have Samba server installed on my Ubuntu server. I have shares setup for all the website directories. I then use my Mac and Coda to edit the files via their shares. This generally works really well but I noticed that my Mac was writing loads of resource fork ._filename files everywhere. I found out the following about the files: These files are created on volumes that don't natively support full HFS file characteristics (e.g. ufs volumes, Windows fileshares, etc). When a Mac file is copied to such a volume, its data fork is stored under the file's regular name, and the additional HFS information (resource fork, type & creator codes, etc) is stored in a second file (in AppleDouble format), with a name that starts with "._". (These files are, of course, invisible as far as OS-X is concerned, but not to other OS's; this can sometimes be annoying...) Does anyone know of a way of sharing files between a Mac client and a Linux server that is most compantable between the two operation systems? Ideally it needs to support the HFS filesystem so that the resource forks are not created and it also needs to support the permissions between server and client.

  Read the article

• Switch Windows 8 from a hybrid MBR/GPT => GPT only on Macbook Pro Retina

  - by Sid

  I used DiskUtility+Bootcamp Wizard to setup my hard drive for Windows 8 (final MSDN). Somewhere in that process, the Apple tools turned my GPT disk into a hybrid MBR/GPT. All my 4 primary MBR partitions are used up, so when I try turning on Bitlocker in Windows 8, it complains about not finding a System drive. I know on Windows 8 the Bitlocker setup tries to create the 200(?)MB system partition if it's missing. However with all 4 partitions filled I suspect it can't create system drive = it can't find it = throws back an error like "BitLocker Setup could not find a target system drive. You may need to manually prepare your drive for BitLocker". I've already tried disabling hibernation, swap file etc. Now I'm thinking that if I were to get rid of the MBR scheme altogether, perhaps I can be alright within the GPT world without MBR's 4 primary partitions limit. So, how can I get rid of the MBR tables on the hybrid scheme in a manner that still leaves Mac OS and Windows 8 in working conditions? Details: Hardware is the MacbookPro Retina. Primary MBR partitions are consumed as follows: EFI partition HFS+ partition (=encrypted, therefore ="Apple_CoreStorage") HFS+ partition (Recovery partition, contains unencrypted Mac bootloader) NTFS partition (Windows8 all-in-one partition) diskutil list output sid-mbpr:~ sid$ diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *251.0 GB disk0 1: EFI 209.7 MB disk0s1 2: Apple_CoreStorage 160.0 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 4: Microsoft Basic Data Win8 90.1 GB disk0s4 GPT vs MBR addresses sid-mbpr:~ sid$ sudo gptsync /dev/rdisk0 Password: Current GPT partition table: # Start LBA End LBA Type 1 40 409639 EFI System (FAT) 2 409640 312909639 Unknown 3 312909640 314179175 Mac OS X Boot 4 314179584 490233855 Basic Data Current MBR partition table: # A Start LBA End LBA Type 1 1 409639 ee EFI Protective 2 409640 312909639 ac Apple RAID 3 312909640 314179175 ab Mac OS X Boot 4 * 314179584 490233855 07 NTFS/HPFS Status: GPT partition of type 'Unknown' found, will not touch this disk.** **: Ignore this message, the gptsync tool is old and doesn't understand the UUID for "Apple_CoreStorage" / FileVault2 partitions. Since LBA addresses are alright, safe to ignore this message.

  Read the article

• Apple Service Diagnostic application on USB key?

  - by Matt 'Trouble' Esse

  I found the following in a text file, and I would like to use the Apple Service Diagnostic Application from a bootable USB key but I cannot find where to download it or set it up? Also is this free software or does it require a separate licence? It sounds like it would be a useful tool for diagnosing Mac problems. The Apple Service Diagnostic application is designed to run both EFI and Mac OS X tests from an external USB hard drive. Apple Service Diagnostic (EFI) runs low-level tests of the hardware directly and does not require Mac OS X, while Apple Service Diagnostic (OS) uses Mac OS X to run tests. Booting and Using the Apple Service Diagnostic Application - Before using Apple Service Diagnostic, disconnect any Ethernet network, USB, and audio cables. - With the USB hard drive containing ASD 3S123 plugged into a USB port, restart the computer and hold down the option key as the computer boots up into the Startup Manager. To run ASD (EFI) select the "ASD EFI 3S123" drive icon and press return or select it with a mouse click. To run ASD (OS) select the "ASD OS 3S123" drive icon and press return or select it with a mouse click. ASD (EFI) will load in 20-30 seconds; ASD (OS) will load in 2-3 minutes. - After running ASD (OS) or ASD (EFI), press the Restart button to restart the computer back into the normal startup volume, or hold down the option key to get back to the Startup Manager. ASD is no longer delivered as an image to be restored onto a DVD. ASD 3S117 and newer versions requires installation onto an external USB hard drive. For more information, please refer to the document "Installing ASD on a USB hard drive".

  Read the article

• Synergy, OSX client, Windows 7 server - No mouse on client

  - by Majenko

  I have the following Synergy setup: +------------++------------++------------++------------+ | Mac || Win 7 || Ubuntu 1 || Ubuntu 2 | |c ||s ||c ||c | +------------++------------++------------++------------+ Mac: OS/X Tiger 10.4.11 (G3) Win 7: Windows 7 Ultimate x64 Ubuntu 1 & Ubuntu 2: Desktop 10.10 Now, everything works nicely between the Win7 server and the two Ubuntu machines. What doesn't work is the Mac. I am running the very latest Synergy (1.4.2, downloaded last night). As far as the Mac is concerned everything should be working fine: Synergy 1.4.2 Client on Darwin 8.11.0 Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC Power Macintosh Unable to connect to pasteboard. Clipboard sharing disabled. 2011-03-22 09:32:56.725 synergyc[406] Can't register screen saver connection 'com.apple.ScreenSaverDaemon' started client connecting to '192.168.0.202': 192.168.0.202:24800 connected to server entering screen leaving screen entering screen leaving screen But it's just not interacting with the display at all (mouse doesn't move, keyboard does nothing). I have tried running ktrace on synergyc and examining the dump, and the only clue I found was that it was trying to interact with the AccessibilityAPI which was disabled at first. Enabling Accessibility has had no effect whatsoever (it has only stopped the failure to open /var/db/.AccessibilityAPIEnabled in the ktrace dump) Anyone managed to get this to work in OS/X Tiger yet? I used to run the server on OS/X and have the windows / unix machines as clients, but as my Windows is now a laptop I'd like that to be the server.

  Read the article

• samba share not on network after upgrading to Ubuntu 12.04LTS. [migrated]

  - by Sylvain Huard

  I just upgraded an old Ubuntu box to 12.04LTS (machine named A-Ubuntu). This is an upgrade not a format re-install. All the accounts and config were preserved. The basic setup is a local network with 2 Ubuntu machines (let say A-Ubuntu, B-Ubuntu) and a MAC (C-MAC). Before the upgrade, all of them could see each other by their names not only the IP address. The local network has a D-Link Router where everybody is connected with RJ-45 wired etherenet (not wi-fi). Since the A-Ubuntu upgrade, we can't see this machine name on the Network and its name is not on machine list in the D-Link router anymore. We can see it's IP address only. I can't access A-Ubuntu from the other two by its name but I can ping it with its address (192.168.0.109). From A-Ubuntu, I can connect and see the shared samba folders on B-Ubuntu and C-MAC. But from B-Ubuntu and C-MAc, I can't connect to A-Ubuntu. Correct me if I'm wrong but this tells me that Samba should be fine and the real problem is that A-Ubuntu does not advertise its name on the Network so the D-Link does not have it in its table so nobody else finds it. After a lot of googling, I see that it is the job of avahi and mdns to do so. Those packages are running, I checked multiple config files for samba, avahi, mdns to see as if it is like the examples on the WEB and also similar to what I find on the working B-Ubuntu machine. This is the same. I did multiple service restart with samba, avahi, remove the firewall to make sure it does not block the hostname broadcast. I rebooted multiple time to make sure the update I was making were effective. Still, Can't see the A-Ubuntu name on the network. Any idea what it can be?, Where to look next?

  Read the article

• Windows 2008 R2 Servers Sending Arp Requests for IPs outside Subnet

  - by Kyle Brandt

  By running a packet capture on my my routers I see some of my servers sending ARP requests for IPs that exist outside of its network. For example if my network is: Network: 8.8.8.0/24 Gateway: 8.8.8.1 (MAC: 00:21:9b:aa:aa:aa) Example Server: 8.8.8.20 (MAC: 00:21:9b:bb:bb:bb) By running a capture on the interface that has 8.8.8.1 I see requests like: Sender Mac: 00:21:9b:bb:bb:bb Sender IP: 8.8.8.20 Target MAC: 00:21:9b:aa:aa:aa Target IP: 69.63.181.58 Anyone seen this behavior before? My understanding of ARP is that requests should only go out for IPs within the subnet... Am I confused in my understanding of ARP? If I am not confused, anyone seen this behavior? Also, these seem to happen in bursts and it doesn't happen when I do something like ping an IP outside of the network. Update: In response to Ian's questions. I am not running anything like Hyper-V. I have multiple interfaces but only one is active (Using BACS failover teaming). The subnet mask is 255.255.255.0 (Even if it were something different it wouldn't explain an IP like 69.63.181.58). When I run MS Network Monitor or wireshark I do not see these ARP requests. What happens is that on the router capturing I see a burst of about 10 requests for IPs outside of the network from the host machine. On the machine itself using wireshark or NetMon I see a flood of ARP responses for all the machines on the network. However, I don't see any requests in the capture asking for those responses. So it seems like maybe it is maybe refreshing the arp cache but including IPs that outside of the network. Also when it does this NetMon doesn't show the ARP requests?

  Read the article

• Ubuntu 12.04 suddenly cannot connect to WPA2/WPA Personal protected connection. Windows 7 can

  - by d4ryl3

  I have a laptop with Windows 7 and Ubuntu 12.04. I have a Cisco E1200 and when I set it up, it created 2 SSIDs. Let's name them: MyConnection (WPA/WPA2 personal), and MyConnection-Guest (no authentication, guest password entered via web browser). I had no problem connecting to MyConnection before, either in Windows 7 and Ubuntu. But now, I can't access MyConnection on Ubuntu. It just says "connecting..." then disconnects after a while. But I'm able to access the internet (on Ubuntu) when I connect to MyConnection-Guest. MAC filtering is off (even if it's on its MAC address is in the white list). Any idea why I'm unable to connect to MyConnection in Ubuntu? Thanks. Update: My Ubuntu installation can connect to ANY WiFi connection (WPA/WEP/no auth), except for MyConnection. Update2: This is what "The not so easy way" returned: Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' Priority group 0 id=0 ssid='MyConnection' id=1 ssid='MyConnection' id=2 ssid='MyConnection' id=3 ssid='MyConnection' WEXT: cfg80211-based driver detected SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 netlink: Operstate: linkmode=1, operstate=5 Own MAC address: xx:xx:xx:xx:xx:xx wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_countermeasures RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec WPS: UUID based on MAC address - hexdump(len=16): 16 3b d8 47 9e 24 50 89 96 16 6d 66 35 f3 58 37 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: Supplicant port status: Unauthorized Added interface eth1

  Read the article

• What is the best VM for developing WPF apps from within OS X?

  - by MarqueIV

  All of my machines are Macs (Mac Pro, MacBook Pro, MacBook Air and Mac Mini (and Apple TV 2.0 too! :) ) but for my day-job, I develop .NET/WPF applications. Normally I just boot into Boot Camp and develop that way, which of course works great, but there are times when I need to simultaneously get to things on my Mac-side of the equation, so I've bought both VMware 3.1 and Parallels 6. Both work, however, even on my Mac Pro where I paid to upgrade to the better video cards (the NVidia 8600s I think vs. the stock ATI cards) the WPF performance bites!! Now this confuses me since both boast that they support not only hardware-accelerated OpenGL 2.1, but also hardware-accelerated DirectX 9 (VMware even allegedly supports DirectX 10!) via their respective virtual drivers and both can run 3D games just fine, even in a window. But even the simple act of resizing a WPF window that has a tiled background results in some HIDEOUS repainting and resizing behaviors. It's damn near closer to what you'd expect over RDP let alone a software-only renderer (forget accelerated hardware completely!) So... can anyone please tell me WTF WPF is doing differently? More importantly, how can I speed up the WPF performance? Should I switch to VirtualBox that also has support for DirectX? Or am I just gonna have to 'byte' the bullet (sorry... had to. So I like puns! Thank Jon Stewart!) and continue using Boot Camp?

  Read the article

• Ubuntu Server attack? how to solve?

  - by saky

  Hello, Something (Someone) is sending out UDP packets sent from our whole ip range. This seems to be multicast DNS. Our server host provided this (Our IP Address is masked with XX): Jun 3 11:02:13 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:23 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:32 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:35 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 I checked my /var/log/auth.log file and found out that someone from China (Using ip-locator) was trying to get in to the server using ssh. ... Jun 3 11:32:00 server2 sshd[28511]: Failed password for root from 202.100.108.25 port 39047 ssh2 Jun 3 11:32:08 server2 sshd[28514]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.100.108.25 user=root Jun 3 11:32:09 server2 sshd[28514]: Failed password for root from 202.100.108.25 port 39756 ssh2 Jun 3 11:32:16 server2 sshd[28516]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.100.108.25 user=root ... I have blocked that IP address using this command: sudo iptables -A INPUT -s 202.100.108.25 -j DROP However, I have no clue about the UDP multicasting, what is doing this? who is doing it? and how I can stop it? Anyone know?

  Read the article

• Packets being dropped by iptables

  - by Shadyabhi

  I am trying to create a Software Access Point in linux. I followed the blog here. Steps I performed: Started dhcp server on wlan0. Properly configured hostapd.conf Enabled packet forwarding & masquerading. Two commands executed regarding iptables: iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface wlan0 -j ACCEPT I enabled logging on iptables & I get this in everything.log Jun 29 19:42:03 MBP-archlinux kernel: [10480.180356] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=38025 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.389102] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=308 TOS=0x00 PREC=0x00 TTL=52 ID=14732 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK PSH URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.389710] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=14988 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK FIN URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.621118] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=63378 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK FIN URGP=0 I have almost no knowledge of iptables, all I did was through googling. So, can anyone help me in making me understand what wrong is happening here? I have tried running tcpdump on wlan0 & http packets are being sent from wlan0.

  Read the article

< Previous Page | 750 751 752 753 754 755 756 757 758 759 760 761  | Next Page >