Search Results

Search found 25300 results on 1012 pages for 'internet speed'.

Page 760/1012 | < Previous Page | 756 757 758 759 760 761 762 763 764 765 766 767  | Next Page >

  • Wireless Bridge with NetGear and TP-Link

    - by Tiago Cruz
    I have a wireless NetGear WGR614 v7 (little old) router connected to the internet, but I can't get a good signal in the other end of my house. I have another new one, model TP-Link TL-WR941ND wireless router. I was able to do the stuff works using a wired cable, but now, I would like to do the same using wireless connections (bridge mode, some like WDS?) Now, the computer connected to TP LINK was able to ping my computer connected to NETGEAR, but we cannot go IP ADDRESS outside my network, only internals ones. What can I do to configure this? Is needed that BOTH wireless routers support BRIDGE mode or only one its good enough? Thanks a lot!!

    Read the article

  • Ubuntu can't find the correct max resolution with Samsung SyncMaster SA300

    - by fatmatto
    i decided to install ubuntu also on my desktop PC (Windows has been exorcised from my life) but i am having some problems i didn't have with previous hardware configurations. My display is a Samsung SyncMaster SA300, on windows vista the maximum resolution (1920x1080) worked well, but now, ubuntu (after installing fglrx drivers) tells me that the maximum resolution is 1600x1200 I googled a lot last night, and i found a lot of people solving this (on different displays though) with xrandr. I was not able to do it, because xrandr keep complaining "you goddamn maximum resolution is 1600x1600". What xranrd clean command say is: mattia@fatdesktop:~$ xrandr Screen 0: minimum 320 x 200, current 1600 x 1200, maximum 1600 x 1600 DFP1 disconnected (normal left inverted right x axis y axis) CRT1 disconnected (normal left inverted right x axis y axis) CRT2 connected 1600x1200+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1600x1200 60.0*+ 1400x1050 60.0 1280x1024 60.0 47.0 43.0 1440x900 59.9 1280x960 60.0 1280x800 60.0 1152x864 60.0 47.0 43.0 1280x768 59.9 56.0 1280x720 60.0 50.0 1024x768 60.0 43.5 800x600 60.3 56.2 47.0 720x576 50.0 720x480 60.0 640x480 60.0 TV disconnected (normal left inverted right x axis y axis) CV disconnected (normal left inverted right x axis y axis) Then according to other internet posts and forums: mattia@fatdesktop:~$ cvt 1920 1080 60 # 1920x1080 59.96 Hz (CVT 2.07M9) hsync: 67.16 kHz; pclk: 173.00 MHz Modeline "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync So now i have to add that modeline mattia@fatdesktop:~$ xrandr --newmode "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync mattia@fatdesktop:~$ xrandr --addmode CRT2 1920x1080_60.00 And here comes the pain: mattia@fatdesktop:~$ xrandr --output CRT2 --mode 1920x1080_60.00 xrandr: **screen cannot be larger than 1600x1600 (desired size 1920x1080)** See? screen cannot be larger than 1600x1600 (desired size 1920x1080) At this point, the 1920x1080 option appears inside the resolution choice menu (the graphical one). But last night, when i tried to select it, my screen went black, and i had to power off the pc. Any clues? am i on the wrong path?

    Read the article

  • The Hunger Games for Aspiring IT Professionals

    - by Dain C. Hansen
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} It seems that no one can escape the buzz around Hunger Games. And who could? Stephen King said it best in his review when he referred to the Collins’ novel as “a violent, jarring speed-rap of a novel that generates nearly constant suspense and may also generate a fair amount of controversy”. So what’s the tie in for IT? Let’s leave the dystopia of District 12 and come back to today’s reality. This is the world of radical IT paradigm shifts that haven’t been seen since Java was introduced in 1995. Everything you learned in school is probably outdated as of Friday. And everything you learned on Friday will probably change when you get to work on Monday. Nevertheless, we’re eager, we’re aspiring, we’re hungry to learn. While the challenges upon us may not rival the venomous bees (or ‘tracker jackers’) seen in this blockbuster, there are certainly obstacles to be found. In preparation, I leave you two pieces of advice - aside from avoiding werewolves… Learn the Cloud If you had asked me what to learn in 1995, I would have said, “Go learn Java”. But now my advice is “Go learn Java and then learn Cloud”. Cloud computing and Java go hand in hand. This is especially true for Oracle’s own Public Cloud which uses Java (via WebLogic 12c) as well as Oracle Database at its core foundation. Understanding the connotations of elasticity, scale, virtualization, and multi-tenancy, (to name just a few) requires a strong foundation in computer science and especially Java to get it right. Without Java, the Cloud is nothing more than a brittle application meagerly deployed on the internet. Get Social and Actively Participate And at all levels. Socializing your ideas internally is dreadfully important. And this means socializing and communicating your good ideas to lines of business, to architects, business analysts, developers, DBAs and Operations. But don’t forget to go external. Stay current by being on the lookout for blogs, tweets, webcasts, papers, podcasts and videos for your technology area. Be not just a subscriber but a participant in these channels as well. Attend industry and vendor sponsored events to learn from the experts – and seek out opportunities to stay connected with those that are smarter than you. You’ll gain more understanding if you participate actively. At the same time you’ll make friends (and allies) and you’ll be glad you did. Tell help you get social and actively participate [while learning the Cloud] here are a couple of pointers for you: See our website on Cloud and Fusion Middleware Subscribe to our regular Fusion Middleware Newsletter Follow us on Twitter and Facebook Find us at one of our key events Meanwhile, happy IT hunger games!

    Read the article

  • Androidify Turns You into an Android-style Avatar

    - by ETC
    Androidify, a free application for Android phones, lets you create an Android-style avatar of yourself (or anyone, for that matter). Swap out the clothes, adjust the side of your noggin, add a pirate eye-patch, the customization options are abundant. Much like the Mii creator on the Wii, Androidify starts you off with the basics: skin color, hair style and color, adjustment of the body size. After that you can tweak things like clothing, accessories, facial hair and more. Once you’re done you can set it as your contact image, send it to others to use as your contact image, save as a photo, and other wise upload it with the social media tools you have on your phone. Hit up the link below to read more and grab a copy. Androidify [Android Market] Latest Features How-To Geek ETC How to Enable User-Specific Wireless Networks in Windows 7 How to Use Google Chrome as Your Default PDF Reader (the Easy Way) How To Remove People and Objects From Photographs In Photoshop Ask How-To Geek: How Can I Monitor My Bandwidth Usage? Internet Explorer 9 RC Now Available: Here’s the Most Interesting New Stuff Here’s a Super Simple Trick to Defeating Fake Anti-Virus Malware Comix is an Awesome Comics Archive Viewer for Linux Get the MakeUseOf eBook Guide to Speeding Up Windows for Free Need Tech Support? Call the Star Wars Help Desk! [Video Classic] Reclaim Vertical UI Space by Adding a Toolbar to the Left or Right Side of Firefox Androidify Turns You into an Android-style Avatar Reader for Android Updates; Now with Feed Widgets and More

    Read the article

  • Add Properties Back to the Context Menu in Firefox

    - by Asian Angel
    Have you noticed that the Properties Command has been removed from the Context Menu in Firefox 3.6? If you have been missing it here is how to get it back. Before With the newest version of Firefox you may have noticed a very useful command missing from the “Context Menu”. Here you can see that when we right clicked on the article link we were unable to “access” the properties for it… Same article and the same problem when trying to “access” the properties for one of the images. After Once you have installed the extension you can once again “access” the properties for those links… And those images… Looking very good… Conclusion If you have been frustrated with the removal of the “Properties Command” from the “Context Menu” in Firefox 3.6, you can now add it back in just a few moments. Links Download the Element Properties extension (Mozilla Add-ons) Similar Articles Productive Geek Tips Prevent Annoying Websites From Messing With the Right-Click Menu in FirefoxAccess Your Bookmarks in the Context Menu with Context BookmarksAdd Print & Print Preview Commands to Firefox’s Context MenuRestore the "Search…" Item to the Folder Context Menu in Windows Vista SP1Create Permanent Tabs in Firefox with PermaTabs Mod TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional The Ultimate Excel Cheatsheet Convert the Quick Launch Bar into a Super Application Launcher Automate Tasks in Linux with Crontab Discover New Bundled Feeds in Google Reader Play Music in Chrome by Simply Dragging a File 15 Great Illustrations by Chow Hon Lam

    Read the article

  • Set up iis7.5 to deny connections outside of LAN for certain folder

    - by Darkcat Studios
    Im setting up a combined website and extranet currently, they both read from the same database on the same server as the site is hosted on. The reason being that the website is fed from the data that the staff plug into the extranet interface. it also links in to AD for authorising access to the extranet. I have the extranet in a folder within the website folder. What I want to do is only allow the extranet to be accessed from computers within our LAN, but allow the main website to be freely accessible to internet users. I have it set up as a generic web server currently, so anyone can view anything (well up to the point where the user is asked to log into the extranet of course! I have read a lot on this but nothing I read applies to, or works in IIS7.5

    Read the article

  • Apache error_log showing which command output

    - by Unai Rodriguez
    Apache's error_log shows lines like the following: --- snip --- which: no ruby in (/sbin:/usr/sbin:/bin:/usr/bin) which: no locate in (/sbin:/usr/sbin:/bin:/usr/bin) which: no suidperl in (/sbin:/usr/sbin:/bin:/usr/bin) which: no get in (/sbin:/usr/sbin:/bin:/usr/bin) which: no fetch in (/sbin:/usr/sbin:/bin:/usr/bin) which: no links in (/sbin:/usr/sbin:/bin:/usr/bin) which: no lynx in (/sbin:/usr/sbin:/bin:/usr/bin) which: no lwp-mirror in (/sbin:/usr/sbin:/bin:/usr/bin) which: no lwp-download in (/sbin:/usr/sbin:/bin:/usr/bin) which: no kav in (/sbin:/usr/sbin:/bin:/usr/bin) --- end --- The architecture is: Internet - Load Balancer - Varnish - Apache There are several web servers behind the load balancer and I have checked at least one of them with rkhunter (link) and couldn't find anything suspicious. Versions: CentOS 5.7 Varnish 2.1.5 Apache 2.2.3 PHP 5.2.17 Does this mean that someone has executed the command which through Apache? How can that happen? Thank you so much.

    Read the article

  • iPhone 3G S sync services problem

    - by Ryan McCue
    When I try and synchronise my iPhone with iTunes, I get a dialog informing me that "syncing has been disabled on this computer". (I've never disabled syncing myself, and it worked perfectly fine a day ago) Music synchronises fine, as do videos, however, my contacts do not. Google Contacts no longer appears in the list to choose from, and the select box is empty. When I choose to re-enable syncing, iTunes informs me that "iTunes was unable to load provider data from Sync Services". I've followed several steps I've found on the internet, including deleting the C:\Users\Ryan\AppData\Roaming\Apple Computer\Sync Services directory, but to no avail. Any ideas on what could be causing this? Is there a Service (in the Windows-form-of-daemon sense) that I accidentally disabled?

    Read the article

  • Screen shots and documentation on the cheap

    - by Kyle Burns
    Occasionally I am surprised to open up my toolbox and find a great tool that I've had for years and never noticed.  The other day I had just such an experience with Windows Server 2008.  A co-worker of mine was squinting to read to screenshots that he had taken using the "Print Screen, paste" method in WordPad and asked me if there was a better tool available at a reasonable cost.  My first instinct was to take a look at CamStudio for him, but I also knew that he had an immediate need to take some more screenshots, so I decided to check and see if the Snipping Tool found in Windows 7 is also available in Windows Server 2008.  I clicked the Start button and typed “snip” into the search bar and while the Snipping Tool did not come up, a Control Panel item labeled “Record steps to reproduce a problem” did. The application behind the Control Panel entry was “Problem Steps Recorder” (PSR.exe) and I have confirmed that it is available in Windows 7 and Windows Server 2008 R2 but have not checked other platforms.  It presents a pretty minimal and intuitive interface in providing a “Start Record”, “Stop Record”, and “Add Comment” button.  The “Start Record” button shockingly starts recording and, sure enough, the “Stop Record” button stops recording.  The “Add Comment” button prompts for a comment and for you to highlight the area of the screen to which your comment is related.  Once you’re done recording, the tool outputs an MHT file packaged in a ZIP archive.  This file contains a series of screen shots depicting the user’s interactions and giving timestamps and descriptive text (such as “User left click on “Test” in “My Page – Windows Internet Explorer”) as well as the comments they made along the way and some diagnostics about the applications captured. The Problem Steps Recorder looks like a simple solution to the most common of my needs for documentation that can turn “I can’t understand how to make it do what you’re reporting” to “Oh, I see what you’re talking about and will fix it right away”.  I you’re like me and haven’t yet discovered this tool give it a whirl and see for yourself.

    Read the article

  • Cisco 877 as a VPN server?

    - by Massimo
    I have a Cisco 877 router which connects my network to the Internet using an ADSL line, a single public IP address and NAT; the IOS version is 15. Everything is working ok, but I'd like to configure this router to be a VPN server, to be able to connect to the network from the outside. I've tried looking for documentation, but everything I can find is related to having the 877 act as a VPN client, or to site-to-site VPNs; I can't find anything about letting single remote computers access the internal network, which is something I can do quite easily using Windows' RRAS or ISA Server. Can the Cisco 877 act as a VPN server for remote client computers? (Looks like it should, but just to be sure...) Which type of VPNs does it support? Do they require some special software on the client machines, or can they be used by standard out-of-the-box Windows computers? And, finally: how to set up this?

    Read the article

  • How would I setup reverse DNS for 2 email servers?

    - by Solignis
    I have an interesting DNS question (well interesting to me atleast). I just installed an hmail server in our remote office to act as an MX backup in the event our exchange server goes down. The 2 host names are mail.campbellsurvey.com mail2.campbellsurvey.com mail points to the address 98.XXX.91.XXX mail2 points to the address 70.XXX.190.XXX How would I setup a PTR record on the ISP end to reflect both hostnames? Does the PTR have to point to EXACTLY mail.campbellsurvey.com or can it point to just campbellsurvey.com? because right now anything passing through the primary static address in our pool (the one used for standard internet) is identified as mail.campbellsurvey.com. My only idea to fix this was to move the mail server to the next available address and give it only it the name mail.campbellsurvey.com but I wanted to see if there was another way. Thanks in advance.

    Read the article

  • Pfsense: Inbound Load Balancing https with sticky connection

    - by Zeux
    first of all I'm very sorry for my English... This is my scenario: Internet Firewall+LB: pfsense_1(Active) + pfsense_2(Passive) in CARP Pool servers: 3 x nginx(PHP5+HTTP+HTTPS) Pfsense 1 and 2 CARP configured with Virtual IP (pubblic). Nginx servers's ips are all private. I want to load balance inbound HTTP and HTTPS connections between the 3 nginx web servers. An importat thing is that the HTTPS connections must be "sticky connections": in HTTPS connections, after login by username and password, I setup a php session and therefore when a client starts a HTTPS connection it will be always redirected to the same nginx server, until it disconnects itself, it closes the page/browser or after a timeout (30minutes?) without activity. Is this possible whit the last release(2.0.1) of pfsense? thank you very much...

    Read the article

  • Isolating VMware virtual machines from the network

    - by jetboy
    I have: VMware Workstation 7 running on a Windows 7 box (with a single NIC), with multiple virtual machines running a range of OSs. The host box is connected to a WRT54G router running Tomato firmware. The router is acting as a wireless bridge to another WRT54G that's wired to my broadband modem. I can access the VMs externally via VNC using VMware's Remote Display. Over time I've had these running: a. Using NAT networking (single IP) with port forwarding on the router and a custom port in VMware for each VM. b. Using bridged networking with static IPs assigned to each VM via MAC address, and port forwarding on the router to each IP running with standard ports. Either way, the host box, and other physical machines on the network are accessible from the VMs. Is there a way to isolate the VMs from the rest of the network, but still maintain internet access and remote VNC to the VMs?

    Read the article

  • Wireshark can see outside of the virtual machine?

    - by OSX Jedi
    I'm running Windows in a VM inside of OSX. If I start Wireshark inside Windows, then a message from OSX pops up saying that Wireshark is trying to monitor all network traffic. If I accept, then Wireshark starts showing all sorts of network activity. This can't be from Windows, because I don't have anything in there doing anything, but I am running things which are communicating through the internet in OSX. Is Wireshark able to see the network activity from OSX? How can it do this if it's inside a virtual machine?

    Read the article

  • What Would Google Do?

    - by David Dorf
    Last year I read Jeff Jarvis' book What Would Google Do? and found it very interesting. Jeff is a long-time journalist that's been studying technology, and more specifically the internet. He used his skills to reverse-engineer Google into a list of "Google rules," then goes on to describe a futuristic world driven by these rules. Its an interesting look at crowd-sourcing, openness, and collaboration across many industries, including retail (Google Shops). This year Jeff Jarvis will be a keynote speaker at CrossTalk, Oracle's user conference dedicated to the retail industry. This year's theme is... Retail Redefined: Redesign. Reinvigorate. Reimagine. I think that's pretty appropriate given the massive changes the industry has undergone during the last three years. The thing I really like about this conference is that we try to let the retailers do most of the talking. I'm very interested in hearing about the innovative projects they've got brewing, and where they think our industry is heading. I'll be speaking, but I'm not sure about what so let me know of any interesting topics.

    Read the article

  • What's the largest message size modern email systems generally support?

    - by Phil Hollenback
    I know that Yahoo and Google mail support 25MB email attachments. I have an idea from somewhere that 10MB email messages are generally supported by modern email systems. So if I'm sending an email between two arbitrary users on the internet, what's the safe upper bound on message size? 1MB? 10MB? 25MB? I know that one answer is 'don't send big emails, use some sort of drop box'. I'm looking for a guideline if you are limited to only using regular smtp email.

    Read the article

  • Enable Full Screen Mode in Media Center Without Trapping the Mouse

    - by DigitalGeekery
    If you have a dual monitor setup and use Windows Media Center, you’re probably aware that when WMC is in full screen mode, it traps the mouse so you can’t work on a second monitor. Here we look at how to solve the annoyance. The Maxifier is an application that allows you to open Media Center in full screen mode without restricting the mouse. It relieves the annoyance of WMC capturing your mouse on a dual monitor setup. Note: If you don’t have two monitors attached, most of The Maxifier’s functions won’t work. Installation and Use Download, extract, and install The Maxifier. (See the download link below) The Maxifier runs minimized in the system tray and you access the options by right-clicking on the icon. If Media Center is not already open, you can choose Start Media Center to start WMC on the main start screen. Or, choose one of the other selections to open another area of Media Center. By default, Maxifier opens Media Center in full screen mode on the secondary monitor. When Media Center is open in full screen mode, you’ll notice you can now freely move your mouse around your multi-monitor setup. When Media Center is open, you’ll see five additional options. The Fit Screen options simply fits Media Center to the full screen, but still show the Windows borders. Full screen options put WMC in full screen mode.   The Maxifier Options allow you to choose from the various start up options. Selecting Watch for Media Center starting will prompt Maxifier to open WMC to the main start page in full screen mode on the secondary monitor automatically, even if you open Media Center without using The Maxifier.  (You may need to restart for this to take effect) If you have more than 2 monitors, you can define on which monitor to open Media Center, and which monitor you consider to be the main screen.   You can also define a number of Hotkeys in The Maxifier settings. First, select the Enable Hotkeys checkbox. To create a Hotkey, click in the text field and then press the keys to use as the Hotkey. To remove a Hotkey, click in the field and press the Delete key.   Conclusion The Maxifier is a simple program that enables Media Center users to take full advantage of a multi-monitor workspace. It works with both Vista and Windows 7. Version 1.4 is a stable application for Vista, and Version 1.5b is a beta application for Windows 7. Looking for more Media Center tips and tweaks? Check out some startup customizations for Windows 7 Media Center, how to automatically mount and view ISO’s in WMC, and how to add background images and themes to Windows 7 Media Center. Link Download the Maxifier Similar Articles Productive Geek Tips Startup Customizations for Media Center in Windows 7Using Netflix Watchnow in Windows Vista Media Center (Gmedia)Lock The Screen While in Full-Screen Mode in Windows Media PlayerSwitch Windows by Hovering the Mouse Over a Window in Windows 7 or VistaIntegrate Boxee with Media Center in Windows 7 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Steve Jobs’ iPhone 4 Keynote Video Watch World Cup Online On These Sites Speed Up Windows With ReadyBoost Awesome World Cup Soccer Calendar Nice Websites To Watch TV Shows Online 24 Million Sites

    Read the article

  • apache performance improvements and maxclients

    - by updog
    I know this has been asked a few (thousand) times around the internet but I was hoping someone whose in the know might be able to comment on my particular setup. I have a web server hosting one site (php/codeigniter) with a wordpress blog in a sub directory. The server has 2GB RAM, 3GHz CPU and I have offloaded the static assets to CloudFlare which is has reduced bandwidth for the actual server by almost 75%. The problem I have is when an email campaign is sent out that links to the site or blog, it slows down. Below is my settings in apache2.conf. Average apache process size is 80M and there is 1.5GB available for apache. <IfModule mpm_prefork_module> StartServers 8 MinSpareServers 5 MaxSpareServers 20 MaxClients 20 MaxRequestsPerChild 2000 </IfModule> I have already setup and installed apc and built some caching into the site and used w3totalcache on the blog. The number of concurrent users is around 2-300 when there is a campaign, are there any further optimisations before

    Read the article

  • CheckPoint VPN-1 SecureClient inability to navigate behind a Linksys WAG300N

    - by AndreaTrasatti
    I have a Linksys WAG300N, I'm accessing my LAN with Wifi and everything works fine on my Windows 7 Enterprise laptop. When I try to connect to my company's VPN the connection succeeds, but I cannot access any internet site either within my work network or public site like Yahoo or Google. In my Linksys control panel I already verified all types of VPNs are enable to passthrough. Normal IPSec and Windows VPN worked in the past without any problems. CheckPoint seems to have a solution, but I do not have the ability to change the IP in my client and of course using another NAT device in between is not a solution for me. Edit: adding link to the Checkpoint solution, https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=sk26189

    Read the article

  • Reverse DNS does not match SMTP banner vs Reverse DNS mismatch

    - by MadBoy
    I have to make decision whether my Reverse DNS should match SMTP banner but Reverse DNS to DNS and vice versa stays different or vice versa. Which one to choose? I have an 2x Exchange 2010 server with one SMTP Sender with TMG 2010. TMG has 2 links connected so that we have 2 separate internet providers. The problem is I have no way to control TMG behavior on which link is used to send emails as it picks it randomly. I have 2 MX records: - mail.test.com which resolves to IP and IP resolves to mail.test.com - mail2.test.com which resolves to IP2 and IP2 resolves to mail.test.com This was done to prevent smtp banner issues but it provides problems with Reverse DNS if the server on the other side is eager enough to do comparison. But I've checked with Google and they also don't have that in perfect condition.

    Read the article

  • Roundcube access from outside local network

    - by Mike K
    I have setup hmailserver on a windows xp pro computer and everything is working great when it comes to getting it to send and receive email. Now here is where my problem comes in... I have setup roundcube using uniserver and everything works great internally. Now, what I am trying to do is to be able to access roundcube from the internet outside of the local network. I have opened up ports 80, 443, and the mysql port yet I am still unable to access this from outside of the network. The error message that I am getting is as followed: Forbidden You don't have permission to access /webmail/ on this server. Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request. I believe something needs to be edited in the apache config file. Any help would be greatly appreciated. I am hoping I dont need to run this on windows server but I'm kinda losing hope and thinking I will need to because I need IIS.

    Read the article

  • Windows Defender Update KB915597 (Definition 1.135.415.0)? Killed My Live Discs

    - by user88311
    Here's my problem, for those willing to read for about 2 minutes here's the entire story, http://answers.microsoft.com/en-us/windows/forum/windows_vista-windows_update/bsod-after-windows-defender-update-kb915597/a4b5fca3-0274-47b4-97c4-61b34c4c4599, for those who want the short version here's what happened. After windows update automatically updated windows defender to kb915597, my computer starting getting bsods on shut down and start up and started experiencing problems withe the usb ports. So I decided to go to the microsoft answers site for help, I know that was probably my first mistake, so I followed their advice and they turned my computer into a large paper weight. Luckily I make physical backups of my c drive every few months and I have one from back in july, so I figured I'd boot up a ubuntu live disc, copy all my files from the past 2 months to a external drive and just copy the backup back to the c drive, that's where I ran into this problem. When I put in either a ubuntu or kubuntu disc, everything goes well, until it finishes the loading bar then when the OS would presumably start up, the computer resets, I've tried with ubuntu, kubuntu and gparted, and only gparted is able to get to the point where it starts up, but even then when I try to access the internet from it, the computer resets, and when I tried to copy the entire C drive partition to a blank external I wasn't able to. So I figured somehow maybe the C drive had something to do with it, so I unplugged the C drive so my computer was just a 2.8 ghz processor and 2 gigs of ram, should have had no problem starting a live disc but the problem still continues. After doing some googling around I've found whenever windows gets a update with the title KB915597 it's pretty much the kill switch for windows, I've tried contacting microsoft tech support and even managed to directly contact a software engineer but as soon as I mention KB915597 they all just blew me off. I hope anybody who reads this has any idea how to fix this, I'm going to attempt to install ubuntu or kubuntu to a external drive using the same computer and see what happens now.

    Read the article

  • Samba server error message in Windows XP

    - by Kumar P
    We have a RHEL5 Linux Server with few Windows XP client boxes. Using Samba server for share files between systems. My server working well in all systems but one Windows XP machine didn't connect to server. Here i give some screen shots for clear idea, For Check network connection i use ping, It working well. I use above way for connect to server. For all other systems it working well. I am getting error message like this. ** I am using squid for proxy in Linux, For me internet also working well in that Windows XP system. ** I Deleted stored user name and password for samba in windows XP. Help me to solve this problem.

    Read the article

  • How to Remote View and Control Your Android Phone

    - by Jason Fitzpatrick
    If you’ve ever wished you could see your Android phone’s screen on your desktop or remote control it using your mouse and keyboard we’ll show you how in this simple guide to gaining remote access to your Android device. Why would you want to gain access? When you’re done with this tutorial you’ll be able to view your phone’s screen on your computer monitor which is great for: putting your Android notifications right along side other notification boxes on your monitor, using it like an on-monitor caller ID, and taking screenshots and screencasts. Also if your phone is rooted (and it should be! rooting unlocks so many great features) you’ll gain the ability to use your computer’s keyboard and mouse to control your Android phone. Remote keyboard/mouse control is great for inputting data on the tiny screen without needing to peck at the on-screen keyboard. Latest Features How-To Geek ETC RGB? CMYK? Alpha? What Are Image Channels and What Do They Mean? How to Recover that Photo, Picture or File You Deleted Accidentally How To Colorize Black and White Vintage Photographs in Photoshop How To Get SSH Command-Line Access to Windows 7 Using Cygwin The How-To Geek Video Guide to Using Windows 7 Speech Recognition How To Create Your Own Custom ASCII Art from Any Image Google Cloud Print Extension Lets You Print Doc/PDF/Txt Files from Web Sites Hack a $10 Flashlight into an Ultra-bright Premium One Firefox Personas Arrive on Firefox Mobile Focus Booster Is a Sleek and Free Productivity Timer What is the Internet? From the Today Show January 1994 [Historical Video] Take Screenshots and Edit Them in Chrome and Iron Using Aviary Screen Capture

    Read the article

  • Reader for Android Updates; Now with Feed Widgets and More

    - by ETC
    Android phone owners rocking the official Google Reader app will be pleased to see the new update includes much requested features such as polished feed widgets, unread counter widgets, and a handy “mark previous as read” button. Widgets have long been one of the most requested feature for Google Reader for Android. This update rolls them out in two forms. News ticker widgets show you current headlines for your Google Reader folders (as seen in the screenshot here); folder widgets function just as unread counters and only take up a 1×1 space. In addition to the widgets another much requested feature made an appearance. While scrolling through your feed you can now mark all the previous entries as read. Hit up the link below to read more or visit the Android Market on your phone to update the application. Updates to the Google Reader App for Android [The Official Google Reader Blog] Latest Features How-To Geek ETC How to Enable User-Specific Wireless Networks in Windows 7 How to Use Google Chrome as Your Default PDF Reader (the Easy Way) How To Remove People and Objects From Photographs In Photoshop Ask How-To Geek: How Can I Monitor My Bandwidth Usage? Internet Explorer 9 RC Now Available: Here’s the Most Interesting New Stuff Here’s a Super Simple Trick to Defeating Fake Anti-Virus Malware Comix is an Awesome Comics Archive Viewer for Linux Get the MakeUseOf eBook Guide to Speeding Up Windows for Free Need Tech Support? Call the Star Wars Help Desk! [Video Classic] Reclaim Vertical UI Space by Adding a Toolbar to the Left or Right Side of Firefox Androidify Turns You into an Android-style Avatar Reader for Android Updates; Now with Feed Widgets and More

    Read the article

< Previous Page | 756 757 758 759 760 761 762 763 764 765 766 767  | Next Page >