Search Results

Search found 22281 results on 892 pages for 'password management'.

Page 773/892 | < Previous Page | 769 770 771 772 773 774 775 776 777 778 779 780  | Next Page >

• How does KMS (Windows Server 2008 R2) differentiate clients?

  - by Joe Taylor

  I have recently installed a KMS Server in our domain and deployed 75 new Windows 7 machines using an image I made using Acronis True Image. There are 2 variations of this image rolled out currently. When I go to activate the machines it returns that the KMS count is not sufficient. On the server with a slmgr /dlv it shows: Key Management Service is enabled on this machine. Current count: 2 Listening on Port: 1688 DNS publishing enabled KMS Priority: Normal KMS cumulative requests received from clients: 366 Failed requests received: 2 Requests with License status unlicensed: 0 Requests with License status licensed: 0 Requests with License status Initial Grace period: 1 Requests with License statusLicense expired or hardware out of tolerance: 0 Requests with License status Non genuine grace period: 0 Requests with License status Notification: 363 Is it to do with the fact that I've used the same image for all the PC's? If so how do I get round this. Would changing the SID help? OK knowing I've been thick whats the best way to rectify the situation. Can I sysprep the machines to OOBE on each individual machine? Or would NewSID work?

  Read the article

• How to fix Windows 7 device removal notification loop

  - by Barry Kelly

  Bit of an odd one this. One of our PCs is getting caught in a loop some time after being turned on, usually after a USB storage device has been attached - sometimes an iPod, sometimes a GPS. Specifically, Windows Explorer starts showing a drive icon and letter (E:, as of right now) for the System partition (the small hidden one at the start of the boot drive). Then, the icon disappears. Then it reappears again. And disappears. It does this very quickly, at what looks like maybe 50 times a second. CPU usage in this loop is also very high; averages about 66%. This machine has an i7 920 CPU, which is quad core with hyperthreading; so this usage rate works out to about 5 100% busy threads, along with whatever normal idle load is (particularly Task Manager itself). Inspecting with Process Explorer shows that the device removal notification infrastructure has gone berserk. The threads in system service processes (i.e. apart from Windows Explorer) which are using all the CPU power relate to device notification. The Disk Management MMC snap-in also fails to run when the loop starts. The only way to break the loop, it seems, is to reboot the machine. Anyone seen anything similar to this, and know of a way to fix it? Machine details: Windows 7 x64, fully patched i7 920, 12GB RAM Intel SSD 80GB (X25-M, I believe; not G2) 2TB 5.2K disk for bulk storage AMD HD 5870 Further hardware details await. I'm going to go through and update all drivers I can find.

  Read the article

• How do I connect to and factory reset a Catalyst 3560 Switch?

  - by Josh

  My company just bought another company. In their server room they had some older hardware, which I would like to repurpose. One of these is a Cisco Switch: C3560G-48TS-S. I found some instructions about this switch here but this is not a guide for a beginner. I have no idea how to connect to this thing to begin running the commands. It says Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. But I can't find anything on how to do this (assuming with telnet?) or even what program to use. I also don't know how to find the IP address of the device to connect to it. My research also says once I get in there, I need to run clear config all Is this the right command? Also, what if I can't get the username and password for these devices? Is there some way to factory reset (my only experience is with devices that have a hardware reset button) EDIT: I should note that when I push the button on the front the three lights blink, which according to the documentation indicated the switch is configured and "not available for express setup"

  Read the article

• Windows 7 pc freezes for an indeterminate amount of time after unlocking

  - by pikes

  Not sure if this type of question is appropriate for this forum, but I've tried everything I can think of to solve this problem aside from format/reinstall. I recently got a new work PC (Dell optiplex 755) with windows 7 professional x64. Standard developer software installed for .net development: VS2008, VS2005, SQL management studio, office 2007, etc. Recently I've been having this weird problem where after I lock my pc, when I try to unlock it, the screen will be black for awhile after unlocking. I can ctl+alt+del and put my password in but then it just goes black. The amount of time on the black screen seems to be related to the amount of time I am away from my PC. If only away a few minutes, it'll take about a minute to get to the desktop. If away for an hour, could take up to 15 minutes. If I lock it and go home for the night, I have to restart my PC in the morning (I've let it sit for an hour after a night of being locked and nothing happened). It doesn't do it every time but definitely the majority of the time. One weird thing I've seen is that if I remote into my machine before trying to log back in it does not do it. I uninstalled all software back to the point when I remember it started happening and it still does it. I was using this PC for a few weeks without this problem happening at all. Anyone know what my next troubleshooting steps could be? My IT department tried to fix it by moving my old profile to another disk and having me log in, effectively recreating a profile from scratch but that didn't solve it. As I said above if this isn't the right forum for these types of questions please let me know. Thanks in advance!

  Read the article

• How intrusive is using VPN?

  - by Slade

  My company lets us work from home sometimes using VPN (during weather emergencies and stuff). When logging in a big window comes up that says the network is private and for employees only and that there's no right to privacy while using VPN. It makes sense that they don't want people poking around their network but I wonder if the company can use the connection to look around my computer while I'm connected. I'm not entirely computer-illiterate but I'm not a networks person at all so the technical documents I've found don't help me. Is that possible, and if so to what degree? UPDATE Thanks Mark. The funneling thing is what I was really asking about. Mostly I was worried that I would already have some IM conversation open or log into eBay forgetting that the VPN was open and that my company IT people would see it or that they would log my eBay password. Thanks again. ANOTHER UPDATE What if my son wants to play online poker or Warcraft etcetera while I have VPN on to work? Can my company think I'm the one playing if I am not typing often?

  Read the article

• Config nginx for slow connection to avoide corrupted doanlowds

  - by user1850273

  We have a Windows 2003 server that nginx 1.3.8 is running. Our problem is users with slow connction about 10K . Our server is serving our program update files and when they download from our server the downloade file is incompleted or crrupted. (Users can not download file with DL manager and the problem is in IE ) for example in slow connection a file with 25mb , after 2Mb downloaded finish . in high speed connections there is no problem. Also when we redirect these slow connection to other port F.e 50005 with the same config they download will be much better but not good as other servers. Which config we must apply to avoide such these download stops or corrupted downloads in slow connection ? this is our server config : worker_processes 1; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent ' '"$http_user_agent"'; access_log logs/access.log main; sendfile off; keepalive_timeout 60; server { listen 80; server_name localhost; location / { root html; deny 127.0.0.3; index index.html index.htm; } } server_tokens off; } Our server use Htaccess password accounting and we can not use IIS on windows , Which soloution you think is better ? IIS with a extention to use apache htaccess ? Or use apache for windows insted of nginx ? Thank You.

  Read the article

• validate weblogic security realm user through java

  - by user1877246

  i have installed weblogic '10.3.4.0' and have created a user in the default security realm 'myrealm'. The authenticator is DefaultAuthenticator. Now, I have to authenticate the user through a stand alone java application. But the application is resposning with 'LDAP: error code 49 - Invalid Credentials': CODE-START ** Properties l_props = new Properties(); LdapContext l_ctx = null; l_props.put(Context.INITIAL_CONTEXT_FACTORY, "com.sun.jndi.ldap.LdapCtxFactory"); l_props.put(Context.PROVIDER_URL, "ldap://localhost:7001"); l_props.put(Context.SECURITY_AUTHENTICATION, "simple"); l_props.put(Context.SECURITY_PRINCIPAL, "cn=username"); l_props.put(Context.SECURITY_CREDENTIALS, "password"); l_ctx = new InitialLdapContext(l_props, null); ** CODE-END ** * ERROR-START * javax.naming.AuthenticationException: [LDAP: error code 49 - Invalid Credentials] at com.sun.jndi.ldap.LdapCtx.mapErrorCode(LdapCtx.java:3041) at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2987) at com.sun.jndi.ldap.LdapCtx.processReturnCode(LdapCtx.java:2789) at com.sun.jndi.ldap.LdapCtx.connect(LdapCtx.java:2703) at com.sun.jndi.ldap.LdapCtx.(LdapCtx.java:293) at com.sun.jndi.ldap.LdapCtxFactory.getUsingURL(LdapCtxFactory.java:175) at com.sun.jndi.ldap.LdapCtxFactory.getUsingURLs(LdapCtxFactory.java:193) at com.sun.jndi.ldap.LdapCtxFactory.getLdapCtxInstance(LdapCtxFactory.java:136) at com.sun.jndi.ldap.LdapCtxFactory.getInitialContext(LdapCtxFactory.java:66) at javax.naming.spi.NamingManager.getInitialContext(NamingManager.java:667) at javax.naming.InitialContext.getDefaultInitCtx(InitialContext.java:288) at javax.naming.InitialContext.init(InitialContext.java:223) at javax.naming.ldap.InitialLdapContext.(InitialLdapContext.java:134) at com.iflex.fcat.misc.TestLDAP.createInitialLdapContext(TestLDAP.java:258) at com.iflex.fcat.misc.TestLDAP.authenticate(TestLDAP.java:170) at com.iflex.fcat.misc.TestLDAP.main(TestLDAP.java:125) ERROR-END

  Read the article

• SSH hangs when executing command remotely

  - by Serty Oan

  Client : OpenSSH_5.1p1 Debian-5ubuntu1 (Ubuntu 9.04) Server : OpenSSH_5.1p1 Debian-5 (Proxmox 2.6.24-7-pve) I use SSH to execute commands remotely on the server (module check_by_ssh of Nagios). But SSH hangs from time to time when trying to execute commands. I can log to the server via SSH but not executing a simple 'ls'. And it seems to block from all clients from the same IP address. Authentication is not the problem, may it be made by SSH keys or password. ssh -l root -p 2222 server.domain.tld 'ls' Here the client debug info debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR *** skipping approx 40 env var ignored debug1: Sending command: ls debug2: channel 0: request exec confirm 1 It hangs there. Then after a random time, it works again (without doing anything). Killing all sshd process on the server seems to work too. It works from a Putty. I saw that some people had trouble like this due to ISP reverse DNS problem, but it does not seem to be the case here. It can work for hours and then not work for half an hour or so. What could explain this behaviour ?

  Read the article

• Configuring SQL Server Express 2005

  - by MrTognio

  What's the proper way to configure SQL Server Express 2005 so that it can allow for a number of clients to get connected to the server? I have my application running both in the server machine and the client machines. Given the nature of my application, clients are the branches geographically distant from each other, and the server itself. Every operation the client records must be reported to the server, because the server needs total control over the usage and production. But, what should I consider when configuring the connection in both sides, the server and the client? I'm not as used to SQL Server, I'm a beginner, however through SQL Server Configuration Manager I have set the main options without success. The problem seems to be related to trusted connections even though I have set it to support both windows and SQL Server authentication. When the client tries to connect to the server using windows authentication it displays no table; when it tries to communicate using a password (SQL Server authentication), tables are successfully displayed but no access is allowed... Thanx in advance!

  Read the article

• sudoer scheme to allow useful access to another web developer yet retain future control of a virtual

  - by Tchalvak

  Background: Virtual Private Server I have a virtual private server that I'm looking to host multiple websites on, and provide access to another web developer. I don't care about putting too many constraints on him, though I wouldn't mind isolating the site that he'll be developing from other sites on the server that I will develop. The problem: retain control Mainly what I want is to make sure that I retain control over the server in the future. I want to reserve the ability to create/promote/demote and other administrative functions that don't deal with web software. If I make him an admin, he can sudo su - and become root and remove root control from me, for example. I need him not to be able to: take away other admin permissions change the root password have control over other security/administrative functions I would like him to still be able to: install software (through apt-get) restart apache access mysql configure mysql/apache reboot edit web development configuration type files in /etc/ Other Standard Setups would be happily considered I've never really set up a good sudoers file, so simple example setups would be very useful, even if they're only somewhat similar to the settings that I'm hoping for above. Edit: I have not yet finalized permissions, so standard, useful sudo setups are certainly an option, the lists above are more what I'm hoping I can do, I don't know that that setup can be done. I'm sure that people have solved this type of problem before somehow, though, and I'd like to go with something somewhat tested as opposed to something I've homegrown.

  Read the article

• Best way to restrict access to a folder in Dropbox

  - by Joe S

  I currently run a business with around 10 staff members and we currently use Dropbox Pro 100GB to share all of our files. It works very well and is inexpensive, however, I am taking on a number of new staff and would like to move the more sensitive documents into their own, protected folder. Currently, we all share one Dropbox account, I am aware that Dropbox for teams supports this, but it is far too expensive for us as a small company. I have researched a number of solutions: 1) Set up a new standard Dropbox account just for use by management, which will contain all of the sensitive documents, and join the shared folder of the rest of my team to access the rest of the documents. As i understand it, this is not possible with a free account, as any dropbox shared folder added to your account will use up your quota 2) Set up some sort of TrueCrypt container, and install TrueCrypt on each trusted staff member's machine, and store the documents inside that. Would this be difficult to use? I'd imagine the sync-ing would not work so well as the disk would technically be mounted at the time of use and any changes would be a change to the actual container rather than individual files. I was just wondering if anyone knows a way to do this without the drawbacks outlined above? Thanks!

  Read the article

• Recovering data from an external hard drive

  - by CCallaghan

  I have a WD Elements 2GB hard drive (formatted NTFS). I accidentally kicked out the USB cable while writing data to the disk, and now I can't access most of the data. Although this was ostensibly my backup drive, there is a great deal of important material on there which was only on there. I realise how idiotic this makes me. (So, formatting is not an option.) Things I've tried/information I've gathered: Windows Explorer will recognise the drive itself. However, it will not access most directories therein (and will sometimes crash when exploring). I can access all of the directories through the command line, but the dir command will often report that it can't read any files in most of the directories. The situation was similar when I hooked it up to an Ubuntu machine: the file explorer crashed, but I could access directories - but not files in those directories - via terminal commands. Several files I tried to copy out either resulted in an I/O error being reported or resulted in the command line crashing. The Disk Management utility on Windows reports a healthy disk formatted as NTFS and not RAW. It also indicates the correct amount of space used up and its capacity (so it seems that the files are not deleted). I've tried to run chkdsk, but that hangs on Step 2 (checking indexes) at 74%. Step 1 reported no bad sectors. I tried Recuva, but that didn't seem to work (stalled at 0% for half an hour). I should also note that the disk doesn't seem to be spinning smoothly; it seems to be chopping back, like it's reading the same sector over and over again. I noticed this after I kicked out the cable. Any help would be greatly appreciated. Update: It would seem the problem has taken a turn for the worse. The external hard drive now shows up on my computer as a local disk and is not mountable by Linux.

  Read the article

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• Preventing back connect in Cpanel servers

  - by Fernando

  We run a Cpanel server and someone gained access to almost all accounts using the following steps: 1) Gained access to an user account due to weak password. Note: this user didn't had shell access. 2) With this user account, he accessed Cpanel and added a cron task. The cron task was a perl script that connected to his IP and he was able to send back shell commands. 3) Having a non jailed shell, he was able to change content of most websites in server specially for users who set their folders to 777 ( Unfortunately a common recommendation and sometimes a requirement for some PHP softwares ). Is there a way to prevent this? We started by disabling cron in Cpanel interface, but this is not enough. I see a lot of other options in which an user could run this perl script. We have a firewall running and blocking uncommon outgoing ports. But he used port 80 and, well, I can't block this port as a lot of processes use them to access things, even Cpanel itself.

  Read the article

• Unable to create files in a directory

  - by vamsi360

  I have created a directory in Virutalbox. Using VBoxManage, I am executing a script inside the Ubuntu VM directory I created above from Ubuntu host OS. But if the script in the VM contains commands for creating a new file, they are not executing. "echo" commands before and after the touch ommand are working fine. I even used root user for VBoxManage to install. I think the directory is not allowing the files to be created . How can I make a directory in Linux to be 777 to all new files created automatically. I mean, even if I make the directory (chmod 777 dir), I am unable to execute the script from the host. Please help. It may be simple permissions problem. Even root is unable to execute. VBoxManage guestcontrol "Ubuntu_10_04" execute --image "/bin/bash" "/home/cloudlet/Desktop/temp2/three" --username root --password root --verbose --wait-exit --wait-stdout -- -l /usr Please help. I am struggling with this problem for the past one week.

  Read the article

• Is it possible to add a WiFi HotSpot to an already established LAN, keep the two separate, and not modify the primary router?

  - by user12844

  I have a set up where my Cisco ASA is sitting in one facility, providing access to the Internet for two buildings. The two buildings are geographically separated by a Wireless Bridge spanning about 10 miles. All computers and equipment inside the LAN are on the same subnet (its pretty small) and we have WiFi AP's in both locations providing Wired and Wireless access to the LAN. Given all the BYOD (Ipods, and SmartPhones etc...) coming into the office as well as Visiting reps etc... we would like to also provide a non-secure, device independent (the devices cannot see or communicate with each other), and LAN independent (the devices cannot see or use anything on the LAN) HotSpot that anyone could use for their Devices that gives them access to the Internet ONLY without needing a password. I get that this could be possible at the facility with my Cisco if I messed with it and created VLANs etc... but then I would need to get it across my Bridge as well and don't think that would be possible without serious reconfiguration of everything. Would really like some kind of magic drop in solution that can kind of piggy back on my LAN without really needing to do very many if any changes to the current set up.

  Read the article

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• Problem running MVC3 app in IIS 7

  - by mjmoore99

  I am having a problem getting a MVC 3 project running in IIS7 on a computer running Windows 7 Home-64 bit. Here is what I did. Installed IIS 7. Accessed the server and got the IIS welcome page. Created a directory named d:\MySite and copied the MVC application to it. (The MVC app is just the standard app that is created when you create a new MVC3 project in visual studio. It just displays a home page and an account logon page. It runs fine inside the Visual Studio development server and I also copied it out to my hosting site and it works fine there) Started IIS management console. Stopped the default site. Added a new site named "MySite" with a physical directory of "d:\Mysite" Changed the application pool named MySite to use .Net Framework 4.0, Integrated pipeline When I access the site in the browser I get a list of the files in the d:\MySite directory. It is as if IIS is not recognizing the contents of d:\MySite as an MVC application. What do I need to do to resolve this?

  Read the article

• Best solution top keep data secure

  - by mrwooster

  What is the simplest and most elegant way of storing a small amount of data in a reasonably secure way? I am not looking for ridiculous levels of advanced encryption (AES-256 is more than enough) and I am only looking to encrypt a small number of files. The files I wish to encrypt are mostly comprised of password lists and SSH keys for servers. Unfortunately it is impossible to keep track of ever changing passwords for my servers (and SSH keys) and so need to keep a list of the passwords. Obviously this list needs to be secure, and also portable (I work from multiple locations). At the moment, I use a 10MB encrypted disk image on my mac (std .dmg AES-256) and just mount it whenever I need access to the data. To my knowledge this is very secure and I am very happy using it. However, the data is not very portable. I would like to be able to access my data from other machines (especially ones running linux), and I am aware that there are quite a few issues trying to mount an encrypted .dmg on linux. An alternative I have considered is to create a tar archive containing the files and use gpg --symmetric to encrypt it, but this is not a very elegant solution as it requires gpg to be installed on every system. So, what over solutions exist, and which ones would you consider to be the most elegant? Ty

  Read the article

• New AD user request form and workflow

  - by user66390

  I'm wondering if anyone is providing a solid solution for creating New Network User Account Request forms, and attaching workflows to them to automate account creation? I'm currently investigating a number of options, but am surprised that such a ubiquitous task hasn't been solved a dozen times over and thoroughly documented. Or at least isn't integrated into current off-the-shelf change management and ticketing systems. Ideally, I'd like for our current ticketing system, ServiceDesk+ to present a standard 'New User' form to department heads, which they can fill in with the required new user details. This triggers a workflow that submits the request as a ticket that can be reviewed and actioned. Actioning the ticket triggers a workflow that creates a user in AD with the details provided, and notifies the department head upon completion. All told, a pretty standard requirement that I'm sure most organizations have. What are other people doing to accomplish this? Edit: I should add, I'm more looking for "supported" methods. As is, I've submitted a number of scripted solutions, none of which have met with manager approval.

  Read the article

• Application Screen Repainting Issues

  - by Jeff Sheldon

  I have this issue lately at work. It drives be nuts, and I finally stopped to ask this question. It's quite often that an application I've been running just randomly fails to repaint itself for a while, usually in the editor screen. I most often see this occurring with Expression Web, Visual Studio 2008/2010 and SQL Server Management studio. These applications are what I work in the most, so I'm not surprised to mostly see it here. But I was curious if anyone else had a solution for this. I've tried: Reboots. The screen shot below is about 10 minutes after a reboot. New Video Drivers. This machine is running a Nvidia Quadro NVS 290 video card with the latest drivers. Closing other applications, this is the only thing running right now. As far as hardware, this machine has Dual Quad-Core Xeon 2.83ghz Processors, with 10 gigs of memory, running Windows XP SP3 64bit. Any help would be great. JNK EDIT: Per comments from deleted (wrong) answer: I'm running dual monitors. Set it to single display, still occurred. Rebooted, and tried it again, and it still occurred. Switched it back to dual screen. My resolution is only 1400x900 on each.

  Read the article

• Samba access works with IP address only

  - by Sebastian Rittau

  I added a Debian etch host (hostname: webserver, IP address: 192.168.101.2) running Samba to a Windows network with a Windows 2003 PDC (IP address 192.168.101.3). The Samba server exports a public guest share, called "Intranet". The server shows up fine in the network, but trying to click on it produces an error dialog, stating I don't have the necessary permissions. So does entering \webserver manually and using \webserver\internet states that the path does not exist. Interestingly, accessing the share by IP address (\192.168.101.2 or \192.168.101.2\intranet) works fine. DNS is configured correctly, and "smbclient //webserver/intranet" on another Linux client works fine. One complicating issue is that the webserver is only a VMware virtual machine running on PDC server. Here is our smb.conf: [global] workgroup = Foobar server string = Webserver wins support = yes ; commenting out these wins server = 192.168.101.3 ; two lines has no effect dns proxy = no guest account = nobody [... snipped some unrelated bits, like logging ...] security = share [... snipped some password-related things ...] domain master = no [intranet] comment = Intranet path = /srv/webserver/contents browseable = yes guest ok = yes guest only = yes read only = yes create mask = 0775 directory mask = 0775

  Read the article

• Is my current htaccess setting hurting SEO?

  - by user656002

  I have a site that I have redirecting to https. I do this to leverage wildcard SSL for my password protected pages. Everything seems to work fine with testing. For example, whether you type in http or www, you always get redirected to the SSL https... That said, I have about 200-300 external backlinks -- many high quality, yet google webmaster (along with SEOMoz), shows I have just 4... Huh? I'm embarrassed to say I just discovered this. This has led me to hypothesize that maybe my settings in htaccess is messed up, so google isn't recognizing a link because it's recorded on another site as http, instead of https. Maybe? At any rate, here is my simple htaccess setting for 301 www to http (The https redirect must be done inside the virtual host file--I think). I don't have anything in the htaccess file for https RewriteCond %{HTTP_HOST} ^www\.example\.com$ [NC] RewriteRule ^(.*)$ http://example.com/$1 [L,R=301] Like I said, everything works fine for redirect over https, so I'd rather not screw up what works. On the other hand something is very wrong with google finding all my back links, so I need to fix something... I'm just wondering that maybe google isn't picking up a my backlinks from other websites recording me as http because I'm at https. Maybe google doesn't care and it's some other issue. Am I barking up the right tree? If so any quick fixes? Thanks as always!

  Read the article

• I can't change mysql port (5.6.12) changing the lines of my.ini (windows 8)

  - by videador

  I was trying to change the port of my mysql server in my local machine but i can't. The version of mysql is 5.6.12, is an installation from wamp and I am on Windows 8. I change these lines in my my.ini file located in (C:\wamp\bin\mysql\mysql5.6.12). [client] #password = your_password port = 3307 socket = /tmp/mysql.sock [wampmysqld] port = 3307 socket = /tmp/mysql.sock key_buffer = 16M max_allowed_packet = 1M The previous values were 3306. Ok then I've reset the server installed, but it doesn't works, the mysql server is still running on 3306. Then, I rename the path of the services with this, to make sure that the my.ini is read by the mysql instance. c:\wamp\bin\mysql\mysql5.6.12\bin\mysqld.exe --defaults-file="C:\wamp\bin\mysql\mysql5.6.12\my.ini" wampmysqld But nothing, it stil doesn't works. My last bullet was to copy the content of my.ini to a file my-default.ini (a file that is placed in C:\wamp\bin\mysql\mysql5.6.12\ and that I don't know what is its mission). However it still doesn't work and the port is still 3306.

  Read the article

• Incorrect Internal DNS Resolution

  - by user167016

  I'm having a DNS issue. Server 2008 R2. The first clue was that after being off the network for a month, I could no longer Remote Desktop into my workstation by name, it wouldn't find it. Both via VPN and internally. But if I connect using its IP, that works. Now I notice in the server's Share and Storage Management, in Manage Sessions, it's displaying the incorrect computer name for some users. So I try, for one example: Ping -a 192.168.16.81 Pinging BOBS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: - replies all successful Then I try Ping RICHARDS_COMPUTER Pinging RICHARDS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: -all replies successful In DHCP, .81 belongs to RICHARDS_COMPUTER I did try flushdns. Not sure if this is related, apologies if it's not, but when I try to connect, I also get prompted: "The identity of the remote computer cannot be verified. Do you want to connect anyway? The remote computer could not be authenticated due to problems with its security certificate. It may be unsafe to proceed.." It then lists the correct name as the name in the certificate from the remote computer, but claims that the certificate is not from a trusted authority. Any thoughts are most appreciated!

  Read the article

< Previous Page | 769 770 771 772 773 774 775 776 777 778 779 780  | Next Page >