Search Results

Search found 20997 results on 840 pages for 'adobe ideas'.

Page 774/840 | < Previous Page | 770 771 772 773 774 775 776 777 778 779 780 781  | Next Page >

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• SSH: Connection Reset by Peer

  - by hopeless

  I have a Solaris 10 server on another network. I can ping it and telnet to it, but ssh doesn't connect. PuTTY log contains nothing of interest (they both negotiate to ssh v2) and then I get "Event Log: Network error: Software caused connection abort". ssh is defintely running: svcs -a | grep ssh online 12:12:04 svc:/network/ssh:default Here's an extract from the server's /var/adm/messages (anonymised) Jun 8 19:51:05 ******* sshd[26391]: [ID 800047 auth.crit] fatal: Read from socket failed: Connection reset by peer However, if I telnet to the box, I can login to ssh locally. I can also ssh to other (non-Solaris) machines on that network fine so I don't believe that it's a network issue (though, since I'm a few hundred miles away, I can't be sure). The server's firewall is disabled, so that shouldn't be a problem root@******** # svcs -a | grep -i ipf disabled Apr_27 svc:/network/ipfilter:default Any ideas what I should start checking? Update: Based on the feedback below, I've run sshd in debug mode. Here's the client output: $ ssh -vvv root@machine -p 32222 OpenSSH_5.0p1, OpenSSL 0.9.8h 28 May 2008 debug2: ssh_connect: needpriv 0 debug1: Connecting to machine [X.X.X.X] port 32222. debug1: Connection established. debug1: identity file /home/lawrencj/.ssh/identity type -1 debug1: identity file /home/lawrencj/.ssh/id_rsa type -1 debug1: identity file /home/lawrencj/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version Sun_SSH_1.1 debug1: no match: Sun_SSH_1.1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.0 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer And here's the server output: root@machine # /usr/lib/ssh/sshd -d -p 32222 debug1: sshd version Sun_SSH_1.1 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: Bind to port 32222 on ::. Server listening on :: port 32222. debug1: Bind to port 32222 on 0.0.0.0. Server listening on 0.0.0.0 port 32222. debug1: Server will not fork when running in debugging mode. Connection from 1.2.3.4 port 2652 debug1: Client protocol version 2.0; client software version OpenSSH_5.0 debug1: match: OpenSSH_5.0 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-Sun_SSH_1.1 debug1: list_hostkey_types: ssh-rsa,ssh-dss debug1: Failed to acquire GSS-API credentials for any mechanisms (No credentials were supplied, or the credentials were unavailable or inaccessible Unknown code 0 ) debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer debug1: Calling cleanup 0x4584c(0x0) This line seems a likely candidate: debug1: Failed to acquire GSS-API credentials for any mechanisms (No credentials were supplied, or the credentials were unavailable or inaccessible

  Read the article

• Can't send email through Comcast SMTP to my domains

  - by Midnight Oil

  I am a Comcast customer with 3 computers and 3 computer users in the house. There are 2 fully updated Macs and one PC running Windows 7. We use Mail on the Macs, and Outlook on Windows 7. All computer accounts are configured to send mail through port 587 of smtp.comcast.net. I also have two personal domains registered with Network Solutions. For the sake of this discussion, call my domains myOwnDomain1.com and myOwnDomain2.com. I have email addresses at both domains. They are of the form [email protected] and [email protected]. Until recently, our email worked as expected. However, sometime between September 13, 2012 and September 19, 2012, we lost the ability to send email through Comcast's SMTP server to the email addresses at my personal domains. If we attempt to send email through Comcast's SMTP to those addresses, the email never arrives. Furthermore, the email clients give no indication of failure. The email just never arrives. The result is the same on all 3 computers and with all accounts on those computers. We can successfully send email through Comcast's SMTP from any of our accounts on any of our computers to any email address other than to my email addresses at my personal domains! However, I receive email at those domains that is not sent through smtp.comcast.net. For example, I can successfully send email from my gmail and yahoo accounts to my email addresses at my personal domains. Furthermore, I can successfully send email through smtp.myOwnDomain1.com to [email protected] and through smtp.myOwnDoman2.com to [email protected]. Comcast says the problem must be at Network Solutions. According to Network Solutions, their logs show they are not blocking reception of the email, and our IP address is not flagged as a spam source. They say the email is simply not arriving. Does anyone have any ideas why we can't send email through Comcast's SMTP server to my domains? As an odd coincidence, we recently noticed a change in Comcast's SMTP service. there is now a 5 minute delay on all outbound mail. Comcast's SMTP server seems to sit on the mail with a 5 minute timer.

  Read the article

• Blank displays after inactivity, mouse cursor not showing up

  - by Mike Christiansen

  I have a Windows 7 Enterprise x86 machine that is exhibiting some strange problems. After some inactivity (it varies how long it takes), when I come back to my computer, both of my monitors are black. The monitors are on, with a black display. Moving the mouse and pressing keys on the keyboard do not work. This happens at least once a day. When I first encountered the issue, I performed a hard shutdown and restarted the computer. About 10% of the time when I did this, the resolutions on my monitors were messed up. The native resolution on the primary monitor is 1600x900, and the native on my secondary is 1440x900. None of the widescreen resolutions would be present in the display properties. I had 800x600, 1024x768, and 1280x1024. As a workaround to this issue, I've found that if I plug in my secondary monitor as the primary monitor, and leave the secondary unplugged, then Windows will start in 1024x768 on the secondary. Then, I can use Windows 7's "Detect" feature and it finds the 1440x900 resolution, and sets it. Then I have to connect the primary monitor to the secondary port and set it as the primary. Then I can switch the two cables, putting the primary into the primary, the secondary into the secondary. Then use the "Detect" feature again, and it finds the correct resolutions. Some time after performing the above, I discovered that when the screens were blanked, I could simply press "Control+Alt+Delete", type in my password, and everything comes up fine - except my mouse cursor. All applications and features work as intended, except there is no mouse cursor (the mouse actually works though...). I have the "Show location of pointer when I press CTRL key" option selected, so I can press CTRL and use my mouse as normal - but I have no actual cursor. When the computer is in this state, UAC is also not functional. Whenever a UAC prompt appears, the screens go black (the original symptoms) and I have to press Escape to exit UAC. Because of the above symptoms (the UAC black screen thing, etc) I beleive winlogon.exe may be the culprit. However, I have no idea how to fix it. I am unable to restart winlogon.exe due to the problems I am having with winlogon.exe (the UAC black screen) Looking for any ideas.... More information Windows 7 x86 Enterprise Domain environment (I have a secondary account with administrator rights) Dell Optiplex 960 Cannot perform "optional" windows updates due to an activation issue (I am testing a windows 7 image, and an activation infrastructure has not been created yet. However, this issue was happening before I was unable to perform windows update, and windows was up to date at the time Updated video card driver (as an attempt to fixing the resolution issue) Disabled all power saving options Please let me know what else you need to help me solve this issue! Thanks in advance, Mike

  Read the article

• installing windows XP in Samsung SENS 145 plus notebook (no CD drive)

  - by user13267

  Hi I was trying to install Windows XP in a Samsung SENS 145 plus Notebook. It does not have a cd drive and I already managed to format it and semi install Windows XP, so now it does not even boot up either. This is what I did: Since it supports USB booting, I first made a bootable USB of Windows XP (Korean version; SP2 I think, may be SP 3) using Novicorp WinToFlash enter link description here. It managed to boot up at first and I was able to format the C driveand get Windows install to start up. It took forever to copy all the files from the USB and after the first reboot, before installation started, I cancelled the reboot from windows install, went to BIOS and changed the boot device priority from USB to internal hard drive. But now on bootup it showed me a list with two options for booting windows XP (much like in the case of a multi OS system) so I assumed that I had formatted drive D by mistake and installed XP there, instead of on C drive. Anyway, I chose one of them and it continued my Windows installation. I got the blue installation screen that shows ads about Windows XP on the right frame and estimated remaining time on the left. However, after completing the process, after the first reboot, instead of showing the Windows XP logo, it says \system32\hall.dll is missing (or corrupted I'm not sure, I needed to install the Korean version of windows and I could not exactly read the error message, however it was one that I have already seen in an English version installation, and I am sure it says either missing or corrupted). The problem is, now it shows the same error again when I try to reboot it from the USB drive as well. I tried to boot a portable version of Linux I made in another USB, but the computer does not boot up from that USB, and it shows hal.dll error when I try to boot it using the WIN XP installation USB I made, as well as when I try to boot it from the hard drive, where I suppose Win XP is now semiinstalled. So now I can't get the computer to start up at all, except going to the BIOS. What else can I try to solve this? Also, would it be possible to install XP on this computer by connecting it to another one running Windows 7 ultimate, through the ethernet card? That is, network just the two computers together, then install windows XP on the notebook from the desktop running windows 7? Please help, I'm running out of ideas on this one. If Korean version of windows XP is the problem then I am willing to install English version as well. (but I need to make sure if that is the real cause of the problem)

  Read the article

• Odd squid transparent redirect behavior

  - by EMiller

  This is the first time I've set up squid. It's running a redirect script that does some text search/replace on html pages, and then saves them to a location on the same machine on the nginx path - then issues the redirect to that URL (it's an art project :D). The relevant lines in squid.conf are http_port 3128 transparent redirect_program /etc/squid/jefferson_redirect.py The jefferson_redirect.py script is based on this script: http://gofedora.com/how-to-write-custom-redirector-rewritor-plugin-squid-python/ The issue: I'm getting strange http redirect behavior. For example, here is the normal request/response from a PHP script that issues a header("Location:"); - a 302 redirect: http://redirector.mysite.com/?unicmd=g+yreka GET /?unicmd=g+yreka HTTP/1.1 Host: redirector.mysite.com User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.1.9) Gecko/20100330 Fedora/3.5.9-1.fc12 Firefox/3.5.9 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive HTTP/1.1 302 Found Date: Tue, 13 Apr 2010 05:15:43 GMT Server: Apache X-Powered-By: PHP/5.2.11 Location: http://www.google.com/search?q=yreka Content-Type: text/html Vary: User-Agent,Accept-Encoding Content-Encoding: gzip Content-Length: 2108 Keep-Alive: timeout=3, max=100 Connection: Keep-Alive Here's what it looks like when running through the squid proxy (note that "redirector.mysite.com" is not the site running squid or nginx): http://redirector.mysite.com/?unicmd=g+yreka GET /?unicmd=g+yreka HTTP/1.1 Host: redirector.mysite.com User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.1.9) Gecko/20100330 Fedora/3.5.9-1.fc12 Firefox/3.5.9 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Proxy-Connection: keep-alive If-Modified-Since: Tue, 13 Apr 2010 05:21:02 GMT HTTP/1.0 200 OK Server: nginx/0.7.62 Date: Tue, 13 Apr 2010 05:21:10 GMT Content-Type: text/html Content-Length: 17865 Last-Modified: Tue, 13 Apr 2010 05:21:10 GMT Accept-Ranges: bytes X-Cache: MISS from jefferson X-Cache-Lookup: HIT from jefferson:3128 Via: 1.1 jefferson:3128 (squid/2.7.STABLE6) Connection: keep-alive Proxy-Connection: keep-alive It is basically working - but the URL http://redirector.mysite.com/?unicmd=g+yreka remains unchanged, while displaying the google page (mostly broken as it's using URLs relative to redirector.mysite.com) I've experienced a similar thing with google results pages: when clicking to another page from google, I get a google URL, with the other site's content. Sorry for the long post - many thanks if you've read this far! Any ideas?

  Read the article

• Linux not picking up new partition correctly on emc pseudo device

  - by James

  Hi We have a database server running oracle rac. We were recently running out of space on the main LUN that it is attached to. I created a new 100GB LUN and concatenated this onto the existing LUN creating a new MetaLUN. After some messing I managed to get linux to recognise the new space. I then created a new partition in on the pseudo device, to use the new space. Previously when I have done this on other system the next step is to create an ASM disk on the new partition and add this disk to the oracle disk group. This however fails. I am aware of various issues with ASM and powerpath, but I don't think this is the issue here. As on while investigating the issue I discovered that one of the underlying logical device is not reflecting the size change. See below; Powermt displays all of the underlying logical units [root@XXXXX~]# powermt display dev=emcpowerd Pseudo name=emcpowerd CLARiiON ID=CKM00091500009 [VFRAC2] Logical device ID=6006016030312200787502866C65DE11 [LUN 30] state=alive; policy=CLAROpt; priority=0; queued-IOs=0 Owner: default=SP A, current=SP A Array failover mode: 1 ============================================================================== ---------------- Host --------------- - Stor - -- I/O Path - -- Stats --- ### HW Path I/O Paths Interf. Mode State Q-IOs Errors ============================================================================== 3 qla2xxx sde SP A0 active alive 0 0 3 qla2xxx sdj SP B0 active alive 0 0 4 qla2xxx sdo SP A1 active alive 0 0 4 qla2xxx sdt SP B1 active alive 0 0 Fdisk on the pseudo device shows correct space. [root@XXXXX ~]# fdisk -l /dev/emcpowerd Disk /dev/emcpowerd: 429.4 GB, 429496729600 bytes 255 heads, 63 sectors/track, 52216 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/emcpowerd1 1 39162 314568733+ 83 Linux /dev/emcpowerd2 39163 52216 104856255 83 Linux fdisk on one of the logical units is wrong [root@XXXXX~]# fdisk -l /dev/sde Disk /dev/sde: 322.1 GB, 322122547200 bytes 255 heads, 63 sectors/track, 39162 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sde1 1 39162 314568733+ 83 Linux /dev/sde2 39163 52216 104856255 83 Linux fdisk on the rest of the units is fine [root@XXXXX ~]# fdisk -l /dev/sdj Disk /dev/sdj: 429.4 GB, 429496729600 bytes 255 heads, 63 sectors/track, 52216 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdj1 1 39162 314568733+ 83 Linux /dev/sdj2 39163 52216 104856255 83 Linux Also when I created the the partition linux did not create the any entries in the /dev directory for the second partition so I created these manually [root@XXXXX dev]# mknod sde2 b 8 66 [root@XXXXX dev]# ls -al sd[ejot]? brw-r----- 1 root disk 8, 65 Dec 29 14:20 sde1 brw-r--r-- 1 root disk 8, 66 Apr 8 20:31 sde2 brw-r----- 1 root disk 8, 145 Dec 29 14:19 sdj1 brw-r--r-- 1 root disk 8, 146 Apr 8 20:33 sdj2 brw-r----- 1 root disk 8, 225 Apr 6 23:12 sdo1 brw-r--r-- 1 root disk 8, 226 Apr 8 20:33 sdo2 brw-r----- 1 root disk 65, 49 Dec 29 14:19 sdt1 brw-r--r-- 1 root disk 65, 50 Apr 8 20:33 sdt2 This is a production server that we cannot easily reboot. Any ideas would be much appreciated. J

  Read the article

• iCloud stuff stops working while connected to OpenVPN [closed]

  - by Taco Bob

  I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again!

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Microsoft signed driver appears as publisher not verfied

  - by Priyanka Gupta

  Task at hand: Microsoft sign drivers on Win 7. I microsoft signed my driver package 3 times every time thinking I might have missed a step or something. However, I cannot seem to get rid of the Windows Security error message "Windows can't verify the publisher of this driver software'. This is not the first time I have signed the driver packages. I was successfully able to sign other driver packages a few months ago. However, with this driver package I keep getting Windows security dialog box. Here's the procedure I follow - Create a new cat file using INF2CAT tool. Self sign the driver using a Versign Class 3 Public Primary Certification Authority - G5.cer. Run the microsoft tests on DTM Servers and clients with the devices that use this driver. Create WLK submission package. Self sign the cab file. Submit the package for certification. The catalog file that comes back after successfully passing tests says Name of signer "Microsoft Windows Hardware Comptibility Publisher". When I check the validity of signature using SignTool, it says the signature is vaild. However, when I try to install the driver with new signed catalog file the windows complain. Any ideas? Edit 11/12/2012: Reply to Eugene's comment Thanks for the help, Eugene. Yes. I did sign two other driver packages before. One of them was modified version of WinUSB driver. I am using the same certificate I used when I signed those two driver packages a few months ago. It costs $250 per signing from Microsoft. I would think that Microsoft would complain about it during certification if the certificate is wrong. I use the following command to self sign the CAT file. I don't have to specify the ceritificate name as there's only one certificate in the directory - Signtool sign /v /a /n CompanyName /t http://timestamp.verisign.com/scripts/timestamp.dll OurCatalogFile.cat Below is the result from running Verify command on the Microsoft signed OurCatalogFile.cat C:\Program Files\Microsoft SDKs\Windows\v7.1\Bin\x64signtool verify /v "C:\User s\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Verifying: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Hash of file (sha1): BDDF39B1DD95881B462164129758A7FFD54F47D9 Signing Certificate Chain: Issued to: Microsoft Root Certificate Authority Issued by: Microsoft Root Certificate Authority Expires: Sun May 09 18:28:13 2021 SHA1 hash: CDD4EEAE6000AC7F40C3802C171E30148030C072 Issued to: Microsoft Windows Hardware Compatibility PCA Issued by: Microsoft Root Certificate Authority Expires: Thu Jun 04 16:15:46 2020 SHA1 hash: 8D42419D8B21E5CF9C3204D0060B19312B96EB78 Issued to: Microsoft Windows Hardware Compatibility Publisher Issued by: Microsoft Windows Hardware Compatibility PCA Expires: Wed Sep 18 18:20:55 2013 SHA1 hash: D94345C032D23404231DD3902F22AB1C2100341E The signature is timestamped: Tue Nov 06 11:26:48 2012 Timestamp Verified by: Issued to: Microsoft Root Authority Issued by: Microsoft Root Authority Expires: Thu Dec 31 02:00:00 2020 SHA1 hash: A43489159A520F0D93D032CCAF37E7FE20A8B419 Issued to: Microsoft Timestamping PCA Issued by: Microsoft Root Authority Expires: Sun Sep 15 02:00:00 2019 SHA1 hash: 3EA99A60058275E0ED83B892A909449F8C33B245 Issued to: Microsoft Time-Stamp Service Issued by: Microsoft Timestamping PCA Expires: Tue Apr 09 16:53:56 2013 SHA1 hash: 1895C2C907E0D7E5C0292B92C6EA8D0E236F525E Successfully verified: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Number of files successfully Verified: 1 Number of warnings: 0 Number of errors: 0 Thank you!

  Read the article

• Email been marked as spam

  - by Rodrigo Ferrari

  Hello friends! Friends, I tried a lot of changes, but no success to send the email correctly formated, I'm using the same domain to send mail and the email pass trough spf and authentication, but has been marked as spam for some accounts using gmail ou google app's. The header's are: Delivered-To: [email protected] Received: by 10.231.208.5 with SMTP id ga5cs194453ibb; Mon, 17 Jan 2011 11:08:33 -0800 (PST) Received: by 10.142.213.18 with SMTP id l18mr4141524wfg.192.1295291312735; Mon, 17 Jan 2011 11:08:32 -0800 (PST) Return-Path: <[email protected]> Received: from hm1315-29.locaweb.com.br (hm1315-29.locaweb.com.br [201.76.49.185]) by mx.google.com with ESMTP id a70si8528144yhd.33.2011.01.17.11.08.32; Mon, 17 Jan 2011 11:08:32 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 201.76.49.185 as permitted sender) client-ip=201.76.49.185; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 201.76.49.185 as permitted sender) [email protected] Received: from hm1974.locaweb.com.br (189.126.112.86) by hm1315-38.locaweb.com.br (PowerMTA(TM) v3.5r15) id h6i9r00nvfo8 for <[email protected]>; Mon, 17 Jan 2011 17:08:31 -0200 (envelope-from <[email protected]>) X-Spam-Status: No Received: from bart0020.locaweb.com.br (bart0020.email.locaweb.com.br [200.234.210.22]) by hm1974.locaweb.com.br (Postfix) with ESMTP id 9C03511E00B5; Mon, 17 Jan 2011 17:08:31 -0200 (BRST) X-LocaWeb-COR: locaweb_2009_x-mail Received: from admin.domain.com.br (hm686.locaweb.com.br [200.234.200.116]) (Authenticated sender: [email protected]) by bart0020.locaweb.com.br (Postfix) with ESMTPA id 4B2F08CAFD6B; Mon, 17 Jan 2011 17:08:31 -0200 (BRST) Message-ID: <[email protected]> Date: Mon, 17 Jan 2011 17:08:31 -0200 Subject: Domain - Assunto From: Sistema <[email protected]> Reply-To: rodrigo <[email protected]> To: balucia <[email protected]> MIME-Version: 1.0 Content-Type: text/html; charset=utf-8 Content-Transfer-Encoding: quoted-printable X-Virus-Scanned: clamav-milter 0.96.5 at hm1974 X-Virus-Status: Clean This header has been marked as spam, I had no more ideas how to fix it and there are people borrowing me about this. Thanks and best regard's.

  Read the article

• Losing internet connectivity on server after installing LogMeIn Hamachi (with server set as gateway node)

  - by Kim Jong-Un

  Our domain controller (SBS 2003) completely lost internet and network connectivity yesterday after I remotely installed LogMeIn Hamachi on it and set it to be a gateway node- in an attempt to create a VPN link between the server and a remote site. I had to go in to the office to resolve the problem as, unsurprisingly, my own remote access to the server was also lost. I was only able to restore network connectivity by deleting a virtual network adapter Hamachi created when making the server the gateway node (called "Hamachi bridge" I believe), then rebooting the server. This is a repeatable problem. Every time I try to get this to work, it just takes the server offline. Why would this bridge affect regular TCP/IP connectivity on the NIC in this way? I have tried a "hub-and-spoke" configuration between the server and our PC at a remote site (server set as hub, remote site as spoke). This caused no such problems with general internet connectivity, and file transfer worked well between the two computers. However, there was a DNS issue with the VPN between the two sites- resulting in Active Directory not being able to communicate between them (could not log on using domain user accounts at remote site if they were not already cached on that machine). I only tried a "gateway" network as LogMeIn support told me: If you can get the Active Directory to work it would only be through a "Gateway" network type with the server acting as the Gateway Node. You would configure the gateway settings on the server in the Hamachi client on that machine to push whatever IP's/DNS settings you prefer and at that point AD would be able (all things being equal) communicate to the client node when it attaches. We do not have any ActiveDirectory configuration info as that's outside the scope of our support. I hope this helps. It would be fantastic if I could get Active Directory to work over a Hamachi VPN connection, without worrying about the server going offline in this way. Does anyone have any ideas how I should proceed, or any theories as to what is going on when I try to use the "gateway" network type? I want to try to narrow down what is going on here.

  Read the article

• Slow wifi from Windows Server 2003 virtualized in XenServer

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks! Update: The issue has been further narrowed down to Windows Server 2003, which Windows Home Server is based on, running in XenServer with the XenServer tools installed.

  Read the article

• Areca 1280ml RAID6 volume set failed

  - by Richard

  Today we hit some kind of worst case scenario and are open to any kind of good ideas. Here is our problem: We are using several dedicated storage servers to host our virtual machines. Before I continue, here are the specs: Dedicated Server Machine Areca 1280ml RAID controller, Firmware 1.49 12x Samsung 1TB HDDs We configured one RAID6-set with 10 discs that contains one logical volume. We have two hot spares in the system. Today one HDD failed. This happens from time to time, so we replaced it. Upon rebuilding a second disc failed. Normally this is no fun. We stopped heavy IO-operations to ensure a stable RAID rebuild. Sadly the hot-spare disc failed while rebuilding and the whole thing stopped. Now we have the following situation: The controller says that the raid set is rebuilding The controller says that the volume failed It is a RAID 6 system and two discs failed, so the data has to be intact, but we cannot bring the volume online again to access the data. While searching we found the following leads. I don't know whether they are good or bad: Mirroring all the discs to a second set of drives. So we would have the possibility to try different things without loosing more than we already have. Trying to rebuild the array in R-Studio. But we have no real experience with the software. Pulling all drives, rebooting the system, changing into the areca controller bios, reinserting the HDDs one-by-one. Some people are saying that the brought the system online by this. Some are saying that the effect is zero. Some say, that they blew the whole thing. Using undocumented areca commands like "rescue" or "LeVel2ReScUe". Contacting a computer forensics service. But whoa... primary estimates by phone exceeded 20.000€. That's why we would kindly ask for help. Maybe we are missing the obvious? And yes of course, we have backups. But some systems lost one week of data, thats why we'd like to get the system up and running again. Any help, suggestions and questions are more than welcome.

  Read the article

• Latency issues over internet

  - by Stevo

  I have a Media Temple server running http://www.popsapp.com which I am having latency issues with. If I run ab -n 100 -c 10 http://www.popsapp.com/ from my local machine I get very bad stats e.g.: Connection Times (ms) min mean[+/-sd] median max Connect: 179 3375 2185.4 2837 12525 Processing: 0 505 693.3 229 4564 Waiting: 0 50 115.4 0 415 Total: 964 3880 2094.5 3159 12608 Whereas if I run it from a rackspace server I have I get this: Connection Times (ms) min mean[+/-sd] median max Connect: 75 76 3.3 75 84 Processing: 235 339 81.4 315 579 Waiting: 159 249 61.7 234 411 Total: 311 415 82.0 390 663 To me this looks like intermediate network issues, but I wouldn't have thought it could be this bad! Any ideas how I can improve it? Here's the trace route traceroute to www.popsapp.com (216.70.105.183), 64 hops max, 52 byte packets 1 192.168.2.1 (192.168.2.1) 3.738 ms 0.953 ms 1.418 ms 2 host-92-22-112-1.as13285.net (92.22.112.1) 27.409 ms 97.093 ms 78.858 ms 3 host-78-151-225-141.static.as13285.net (78.151.225.141) 61.830 ms 170.484 ms 113.288 ms 4 host-78-151-225-80.static.as13285.net (78.151.225.80) 101.513 ms host-78-151-225-22.static.as13285.net (78.151.225.22) 64.718 ms 47.309 ms 5 xe-11-1-0-rt001.sov.as13285.net (62.24.240.14) 98.381 ms 114.424 ms xe-11-1-0-rt001.the.as13285.net (62.24.240.6) 96.592 ms 6 host-78-144-1-59.as13285.net (78.144.1.59) 36.799 ms host-78-144-1-63.as13285.net (78.144.1.63) 178.426 ms host-78-144-1-61.as13285.net (78.144.1.61) 85.516 ms 7 xe-10-0-0-scr010.thn.as13285.net (78.144.0.224) 88.158 ms host-78-144-0-207.as13285.net (78.144.0.207) 35.132 ms host-78-144-0-153.as13285.net (78.144.0.153) 121.464 ms 8 limelight-pp-thn.as13285.net (78.144.3.6) 46.987 ms limelight-pp-sov.as13285.net (78.144.5.18) 108.025 ms 40.169 ms 9 tge11-1.fr4.lga.llnw.net (69.28.172.149) 109.603 ms ve6.fr4.lon.llnw.net (68.142.88.221) 121.681 ms 38.609 ms 10 tge11-1.fr4.lga.llnw.net (69.28.172.149) 111.981 ms 113.744 ms 111.711 ms 11 tge8-2.fr4.iad.llnw.net (69.28.189.34) 117.102 ms ve5.fr4.iad.llnw.net (69.28.171.214) 184.372 ms 146.178 ms 12 cr02-1-1.iad1.net2ez.com (65.97.48.254) 182.880 ms net2ez.tge2-2.fr4.iad.llnw.net (69.28.156.170) 150.489 ms 121.862 ms 13 65.97.50.26 (65.97.50.26) 184.620 ms cr02-1-1.iad1.net2ez.com (65.97.48.254) 156.136 ms 131.963 ms 14 65.97.50.26 (65.97.50.26) 124.899 ms 126.537 ms 123.322 ms 15 e1.4.as02.iad01.mtsvc.net (70.32.64.246) 134.647 ms 186.307 ms 211.059 ms 16 popsapp.com (216.70.105.183) 118.876 ms 113.189 ms vzx258.mediatemple.net (216.70.104.17) 131.012 ms Looks to me like there is significant delay across the limelight network. This would explain why the traceroute via my rackspace server doesn't suffer from the same delay as they will be using their own trunk.

  Read the article

• Disable Acer eRecovery system

  - by Joel Coehoorn

  The meat of this question is that I'm looking for a way to either require a password before using a recovery partition or "break" the recovery partition (specifically, Acer eRecovery) in a way that I can later "unbreak" only by booting normally into windows first. Here's the full details: I have a set of new Acer Veriton n260g machines in a computer lab. A lot work went into setting up this lab to work well - for example, Office 2007 and other programs needed by the students were installed, all windows updates are applied, and a default desktop is setup. All in all it's several hours work to fully set up one machine. Unfortunately, I don't currently have the ability to easily image these machines, and even if I did I would want to avoid downtime even while an image is restored. Therefore, I've taken steps to lock them down — namely DeepFreeze and a bios password to prevent booting from anywhere but the frozen hard drive. DeepFreeze is an amazing product — as long as you boot from the frozen hard drive, there is no way to actually make permanent changes to that hard drive. Anything you do is wiped after the machine restarts. It lets me give students the leeway to do what they want on lab computers without worrying about them breaking something. The problem is that even with the bios locked and set to only boot from the hard drive, these Acers still have a simple way to choose a different boot source: shut them down and put a paper click in a little hole at the top while you turn it on again. This puts them into the "Acer eRecovery" mode. This by itself is no big deal — you can still power cycle with no impact. But if you then click through the menu to reset the machine (we're now past the point of curiosity and on to intent) it will wipe the hard drive and restore it to the original state. Of course, a few students have already figured this out and reset a couple machines. That's unfortunate, but inevitable. I don't want to destroy the ability to do this entirely (which I could by repartitioning the drives to remove the recovery partition) but I would like a way to require a password first, or "break" the recovery system in a way that I can "unbreak" only if I first un-freeze the hard drive in DeepFreeze. Any ideas?

  Read the article

• Fedora 13 post security update boot problem

  - by Alex

  Hello. About a month ago I installed a security update that had new Kernek 2.6.34.x from 2.6.33.x), this is when the problem occurred for the first time. After the install my computer would not boot at all, black screen without any visible hard drive activity (I gave it good 30 minutes on black screen, before took actions)... I poped in installation DVD and went in rescue mode to change back the boot option to old kernel (was just a guess where the problem was). After restart computer loaded just file, took a long time for it to start because of SELinux targeted policy relabel is required. Relabeling could take very long time depending on file size. I assumed that the update got messed up somehow and continued working with modified boot option. Couple of days ago, there was another kernel update. I installed it and same problem as before. This rules out corrupted update theory... Black screen right after 'BIOS' screen before OS gets loaded. I had to rescue system again... Below is copy of my grub.conf file. I am fairly new to LINUX (couple of years of experience), mostly development and basic config... nothing crazy. # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/vg_obalyuk-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda default=2 timeout=0 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.34.6-54.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-54.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-54.fc13.i686.PAE.img title Fedora (2.6.34.6-47.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-47.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-47.fc13.i686.PAE.img title Fedora (2.6.33.8-149.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.33.8-149.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.33.8-149.fc13.i686.PAE.img I like my system to be up to date... Let me know if I can post any other files that can be of help. Has anyone else had this problem? Does anyone has any ideas how to fix this problem? p.s. Anything helps, you ppl are great! thx for ur time.

  Read the article

• Microsoft signed drivers appears as publisher not verfied

  - by Priyanka Gupta

  Task at hand: Microsoft sign drivers on Win 7. I microsoft signed my driver package 3 times every time thinking I might have missed a step or something. However, I cannot seem to get rid of the Windows Security error message "Windows can't verify the publisher of this driver software'. This is not the first time I have signed the driver packages. I was successfully able to sign other driver packages a few months ago. However, with this driver package I keep getting Windows security dialog box. Here's the procedure I follow - Create a new cat file using INF2CAT tool. Self sign the driver using a Versign Class 3 Public Primary Certification Authority - G5.cer. Run the microsoft tests on DTM Servers and clients with the devices that use this driver. Create WLK submission package. Self sign the cab file. Submit the package for certification. The catalog file that comes back after successfully passing tests says Name of signer "Microsoft Windows Hardware Comptibility Publisher". When I check the validity of signature using SignTool, it says the signature is vaild. However, when I try to install the driver with new signed catalog file the windows complain. Any ideas? Edit 11/12/2012: Reply to Eugene's comment Thanks for the help, Eugene. Yes. I did sign two other driver packages before. One of them was modified version of WinUSB driver. I am using the same certificate I used when I signed those two driver packages a few months ago. It costs $250 per signing from Microsoft. I would think that Microsoft would complain about it during certification if the certificate is wrong. I use the following command to self sign the CAT file. I don't have to specify the ceritificate name as there's only one certificate in the directory - Signtool sign /v /a /n CompanyName /t http://timestamp.verisign.com/scripts/timestamp.dll OurCatalogFile.cat Below is the result from running Verify command on the Microsoft signed OutCatalogFile.cat C:\Program Files\Microsoft SDKs\Windows\v7.1\Bin\x64signtool verify /v "C:\User s\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Verifying: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Hash of file (sha1): BDDF39B1DD95881B462164129758A7FFD54F47D9 Signing Certificate Chain: Issued to: Microsoft Root Certificate Authority Issued by: Microsoft Root Certificate Authority Expires: Sun May 09 18:28:13 2021 SHA1 hash: CDD4EEAE6000AC7F40C3802C171E30148030C072 Issued to: Microsoft Windows Hardware Compatibility PCA Issued by: Microsoft Root Certificate Authority Expires: Thu Jun 04 16:15:46 2020 SHA1 hash: 8D42419D8B21E5CF9C3204D0060B19312B96EB78 Issued to: Microsoft Windows Hardware Compatibility Publisher Issued by: Microsoft Windows Hardware Compatibility PCA Expires: Wed Sep 18 18:20:55 2013 SHA1 hash: D94345C032D23404231DD3902F22AB1C2100341E The signature is timestamped: Tue Nov 06 11:26:48 2012 Timestamp Verified by: Issued to: Microsoft Root Authority Issued by: Microsoft Root Authority Expires: Thu Dec 31 02:00:00 2020 SHA1 hash: A43489159A520F0D93D032CCAF37E7FE20A8B419 Issued to: Microsoft Timestamping PCA Issued by: Microsoft Root Authority Expires: Sun Sep 15 02:00:00 2019 SHA1 hash: 3EA99A60058275E0ED83B892A909449F8C33B245 Issued to: Microsoft Time-Stamp Service Issued by: Microsoft Timestamping PCA Expires: Tue Apr 09 16:53:56 2013 SHA1 hash: 1895C2C907E0D7E5C0292B92C6EA8D0E236F525E Successfully verified: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Number of files successfully Verified: 1 Number of warnings: 0 Number of errors: 0 Thank you!

  Read the article

• Volume group disappeared, LVs still available

  - by Ben

  I've run into an issue with my KVM host which runs VMs on a LVM volume. As of last night the logical volumes are no longer seen as such (I can't create snapshots of them even though I have been for months now). Running any scans all result in nothing being found: [root@apollo ~]# pvscan No matching physical volumes found [root@apollo ~]# vgscan Reading all physical volumes. This may take a while... No volume groups found root@apollo ~]# lvscan No volume groups found If I try restoring the VG conf backup from /etc/lvm/backups/vg0 I get the following error: [root@apollo ~]# vgcfgrestore -f /etc/lvm/backup/vg0 vg0 Couldn't find device with uuid 20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt. Cannot restore Volume Group vg0 with 1 PVs marked as missing. Restore failed. /etc/lvm/backups/vg0 has the following for the physical volume: physical_volumes { pv0 { id = "20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt" device = "/dev/sda5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 4292870143 # 1.99902 Terabytes pe_start = 384 pe_count = 524031 # 1.99902 Terabytes } } fdisk -l /dev/sda shows the following: [root@apollo ~]# fdisk -l /dev/sda Disk /dev/sda: 6000.1 GB, 6000069312512 bytes 64 heads, 32 sectors/track, 5722112 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000188b7 Device Boot Start End Blocks Id System /dev/sda1 2 32768 33553408 82 Linux swap / Solaris /dev/sda2 32769 33280 524288 83 Linux /dev/sda3 33281 1081856 1073741824 83 Linux /dev/sda4 1081857 3177984 2146435072 85 Linux extended /dev/sda5 1081857 3177984 2146435071+ 8e Linux LVM The server is running a 4 disk HW RAID10 which seems perfectly healthy according to megacli and smartd. The only odd message in /var/log/messages is the following which shows up every couple of hours: Jun 10 09:41:57 apollo udevd[527]: failed to create queue file: No space left on device Output of df -h [root@apollo ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 1016G 119G 847G 13% / /dev/sda2 508M 67M 416M 14% /boot Does anyone have any ideas what to do next? The VMs are all running fine at the moment apart from not being able to snapshot them. Updated with extra info It's not a lack of inodes: [root@apollo ~]# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda3 67108864 48066 67060798 1% / /dev/sda2 32768 47 32721 1% /boot pvs, vgs & lvs either output nothing or "No volume groups found".

  Read the article

• Forwarding RDP via a Linux machine using iptables: Not working

  - by Nimmy Lebby

  I have a Linux machine and a Windows machine behind a router that implements NAT (the diagram might be overkill, but was fun to make): I am forwarding RDP port (3389) on the router to the Linux machine because I want to audit RDP connections. For the Linux machine to forward RDP traffic, I wrote these iptables rules: iptables -t nat -A PREROUTING -p tcp --dport 3389 -j DNAT --to-destination win-box iptables -A FORWARD -p tcp --dport 3389 -j ACCEPT The port is listening on the Windows machine: C:\Users\nimmy>netstat -a Active Connections Proto Local Address Foreign Address State (..snip..) TCP 0.0.0.0:3389 WIN-BOX:0 LISTENING (..snip..) And the port is forwarding on the Linux machine: # tcpdump port 3389 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 01:33:11.451663 IP shieldsup.grc.com.56387 > linux-box.myapt.lan.ms-wbt-server: Flags [S], seq 94663035, win 8192, options [mss 1460], length 0 01:33:11.451846 IP shieldsup.grc.com.56387 > win-box.myapt.lan.ms-wbt-server: Flags [S], seq 94663035, win 8192, options [mss 1460], length 0 However, I am not getting any successful RDP connections from the outside. The port is not even responding: C:\Users\outside-nimmy>telnet example.com 3389 Connecting To example.com...Could not open connection to the host, on port 3389: Connect failed Any ideas? Update Per @Zhiqiang Ma, I looked at nf_conntrack proc file during a connection attempt and this is what I see (192.168.3.1 = linux-box, 192.168.3.5 = win-box): # cat /proc/net/nf_conntrack | grep 3389 ipv4 2 tcp 6 118 SYN_SENT src=4.79.142.206 dst=192.168.3.1 sport=43142 dport=3389 packets=6 bytes=264 [UNREPLIED] src=192.168.3.5 dst=4.79.142.206 sport=3389 dport=43142 packets=0 bytes=0 mark=0 secmark=0 zone=0 use=2 2nd update Got tcpdump on the router and it seems that win-box is sending an RST packet: 21:20:24.767792 IP shieldsup.grc.com.45349 > linux-box.myapt.lan.3389: S 19088743:19088743(0) win 8192 <mss 1460> 21:20:24.768038 IP shieldsup.grc.com.45349 > win-box.myapt.lan.3389: S 19088743:19088743(0) win 8192 <mss 1460> 21:20:24.770674 IP win-box.myapt.lan.3389 > shieldsup.grc.com.45349: R 721745706:721745706(0) ack 755785049 win 0 Why would Windows be doing this?

  Read the article

• High I/O latency with software RAID, LUKS encrypted and LVM partitioned KVM setup

  - by aef

  I found out a performance problems with a Mumble server, which I described in a previous question are caused by an I/O latency problem of unknown origin. As I have no idea what is causing this and how to further debug it, I'm asking for your ideas on the topic. I'm running a Hetzner EX4S root server as KVM hypervisor. The server is running Debian Wheezy Beta 4 and KVM virtualisation is utilized through LibVirt. The server has two different 3TB hard drives as one of the hard drives was replaced after S.M.A.R.T. errors were reported. The first hard disk is a Seagate Barracuda XT ST33000651AS (512 bytes logical, 4096 bytes physical sector size), the other one a Seagate Barracuda 7200.14 (AF) ST3000DM001-9YN166 (512 bytes logical and physical sector size). There are two Linux software RAID1 devices. One for the unencrypted boot partition and one as container for the encrypted rest, using both hard drives. Inside the latter RAID device lies an AES encrypted LUKS container. Inside the LUKS container there is a LVM physical volume. The hypervisor's VFS is split on three logical volumes on the described LVM physical volume: one for /, one for /home and one for swap. Here is a diagram of the block device configuration stack: sda (Physical HDD) - md0 (RAID1) - md1 (RAID1) sdb (Physical HDD) - md0 (RAID1) - md1 (RAID1) md0 (Boot RAID) - ext4 (/boot) md1 (Data RAID) - LUKS container - LVM Physical volume - LVM volume hypervisor-root - LVM volume hypervisor-home - LVM volume hypervisor-swap - … (Virtual machine volumes) The guest systems (virtual machines) are mostly running Debian Wheezy Beta 4 too. We have one additional Ubuntu Precise instance. They get their block devices from the LVM physical volume, too. The volumes are accessed through Virtio drivers in native writethrough mode. The IO scheduler (elevator) on both the hypervisor and the guest system is set to deadline instead of the default cfs as that happened to be the most performant setup according to our bonnie++ test series. The I/O latency problem is experienced not only inside the guest systems but is also affecting services running on the hypervisor system itself. The setup seems complex, but I'm sure that not the basic structure causes the latency problems, as my previous server ran four years with almost the same basic setup, without any of the performance problems. On the old setup the following things were different: Debian Lenny was the OS for both hypervisor and almost all guests Xen software virtualisation (therefore no Virtio, also) no LibVirt management Different hard drives, each 1.5TB in size (one of them was a Seagate Barracuda 7200.11 ST31500341AS, the other one I can't tell anymore) We had no IPv6 connectivity Neither in the hypervisor nor in guests we had noticable I/O latency problems According the the datasheets, the current hard drives and the one of the old machine have an average latency of 4.12ms.

  Read the article

• Apache ProxyPass Missing Images

  - by EpicOfChaos

  I have a apache server that sits in front of my glassfish server. mydomain.com goes directly to my static files on apache, than if you hit the subdomain forum.mydomain.com it goes to the glassfish webapp forum/ at 127.0.0.1:8080/forum/. This proxy seems to work it takes me to the web app but all of the images are missing! Here is how I go my virtual host setup. NameVirtualHost *:80 <VirtualHost *:80> ServerName www.mydomain.com ServerAlias subdomain.mydomain.com mydomain.com DocumentRoot "/usr/local/apache/htdocs" </VirtualHost> <VirtualHost *:80> ServerName forum.mydomain.com # any logging config, etc, that you need ProxyPass / http://127.0.0.1:8080/forum/ ProxyPassReverse / http://127.0.0.1:8080/forum/ </VirtualHost> And in the access log this is what I am seeing. [15/Jan/2012:03:28:02 +0000] "GET /forums/list.page HTTP/1.1" 200 12861 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/logo.jpg HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/styles/style.css?1326582403934 HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_recentTopics.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_search.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_members.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/styles/en_US.css?1326582403934 HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_groups.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/folder_big.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_login.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/whosonline.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_register.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/ping_session.jsp HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/folder_lock.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/folder.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/folder_new.gif HTTP/1.1" 404 1075 Any Ideas why the images are not working?

  Read the article

• LXC container can only access host via bridge

  - by vitaut

  I have an LXC container with i686 Ubuntu 12.04 running on a x86_64 Ubuntu 12.04 host. I've set up a bridge using instructions here. However the ping from the container only goes through to the host and not to other machines on the local network. Similarly only the host and not the other machines see the container OS. The host's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback iface eth0 inet manual auto br0 iface br0 inet dhcp bridge_ports eth0 bridge_fd 0 bridge_maxwait 0 The container's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp And here's the relevant part of the container's config: lxc.network.type=veth lxc.network.link=br0 lxc.network.flags=up Any ideas what I'm doing wrong? Additional info: The output of iptables-save on host: $ sudo iptables-save # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *filter :INPUT ACCEPT [6854:721708] :FORWARD ACCEPT [4067:538895] :OUTPUT ACCEPT [4967:522405] COMMIT # Completed on Sat Oct 26 06:06:48 2013 # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *nat :PREROUTING ACCEPT [82235:21547307] :INPUT ACCEPT [16:1070] :OUTPUT ACCEPT [9386:583359] :POSTROUTING ACCEPT [14693:1291952] -A POSTROUTING -s 10.0.3.0/24 ! -d 10.0.3.0/24 -j MASQUERADE COMMIT # Completed on Sat Oct 26 06:06:48 2013 The output of brctl show on host: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.080027409684 no eth0 vethBkwWyV The output of ifconfig br0 on host: $ ifconfig br0 br0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232863 errors:0 dropped:0 overruns:0 frame:0 TX packets:59518 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34437354 (34.4 MB) TX bytes:198492871 (198.4 MB) The output of ifconfig eth0 on host: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:299419 errors:0 dropped:0 overruns:0 frame:0 TX packets:203569 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:59077446 (59.0 MB) TX bytes:372056540 (372.0 MB) The output of ifconfig eth0 on container: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:16:3e:74:08:2b inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe74:82b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:81 errors:0 dropped:0 overruns:0 frame:0 TX packets:113 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8506 (8.5 KB) TX bytes:9021 (9.0 KB)

  Read the article

• Windows XP installation problems

  - by Samurai Waffle

  I recently asked a question on here, and thought I had it working... Here is a link to it. Windows XP Installation problems So basically I'm having trouble getting XP installed. To sum it up, a computer I have had a boot sector virus, and I used Darik's Nuke and Boot to wipe the hard drive clean. So the hard drive has nothing on it. I had to try and install Windows through a DOS prompt, because for some reason it won't read it off the DVD. The UBCD is able to look at the files located on the DVD I have in, but I can't boot from it for some reason. So I extracted it to a USB drive, booted to DOS and started the setup process. Here's the weird thing with DOS... It can only find the C: drive. The C: drive in DOS is the flash drive that I have in, running DOS. I can't find the hard drive anywhere! So anyways, after starting the setup process, it copied the files over to the "hard drive" (which took 16 hours because the version of DOS I ran couldn't run smartdrv.exe), and it said the computer had to reboot. So I let it reboot, and it stopped and said there is no boot device. So I popped in UBCD that I have installed on a flash drive, and I discovered that it had copied the Windows files over to the flash drive and not the hard drive. It never asked where it should extract the files... So I toyed around with UBCD, ran a memory test on the hard drive to make sure it was fine, and it came out clean. So I'm stuck now. How can I get this installed? Writing this, I came up with an idea. If I copy the DOS startup files over to the hard drive, would I be able to start DOS from it? If so, I believe that could fix my problems. Any help is greatly appreciated, because I am running out of ideas and am at my wits end with this computer.

  Read the article

• How could I let Skydrive desktop sync to MicroSD in Windows 8 tablet?

  - by peSHIr

  I have a Samsung Slate 7 tablet with (now) Windows 8 on it. This machine has a 64 Gb SSD and I have a 64 Gb MicroSD card in it. I also have a Skydrive on my main Microsoft ID that contains about 45 Gb of content. With Windows and some development stuff installed, my Skydrive will not fit on the main drive of the tablet. (Besides, my idea was to keep data on the memory card anyway, to make it easier to repave the machine without data loss if need be.) My problem should now be clear: I want to install the Skydrive desktop app to sync my Skydrive to the MicroSD card. This is not possible, as Skydrive does not allow syncing files to removable drives. I have tried a number of things already, but none of them worked: Use the mklink command line tool to create a directory link/junction from a folder name on SSD to a folder on the MicroSD and then try to install Skydrive sync to the SSD link folder. Skydrive however still recognizes this as something it does not want to sync onto. The various different filter drivers mentioned on Agnipulse (including the Hitachi one) that should make windows see some or all of the removable drives in the system as fixed drives do not seem work on (64-bit) Windows 8: they either can't be installed, do nothing and/or cause Windows 8 to go into Automatic Repair mode when rebooting. The Lexar BootIt app seems to be meant to flip the relevant bit in the on-board drive controller of supported USB pen drives, but I tried it anyway. Of course it did nothing to how the MicroSD card was seen. I have now run out of ideas, it seems, and I was wondering if anyone here has a solution to let Windows 8 see the MicroSD memory card in my tablet as a fixed drive instead of removable drive, or some other way of getting the Skydrive desktop to sync my Skydrive data to that MicroSD card. And to be complete: this is not a duplicate question of this or this as those ask about getting USB drives multiple partitions to work on Windows XP. This question is specific about getting desktop Skydrive to sync to MicroSD card in Windows 8, which seems to be a question I have not seen on superuser so far.

  Read the article

< Previous Page | 770 771 772 773 774 775 776 777 778 779 780 781  | Next Page >