Search Results

Search found 39511 results on 1581 pages for 'exc bad access'.

Page 78/1581 | < Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >

• Delayed internet access

  - by Joel Coel

  When I (and presumably my users) first start up or log in to my computer I can't get internet access until several minutes after logging in. Internet pages like serverfault.com will time out. During this time I can access internal web servers. Sometimes pinging the gateway seems to fix the problem. I'm using Windows 7 on this machine with wifi, and the problem seems limited to the wifi network, which is on a separate vlan. The wired network does not share the problem, but I know it's not the wifi connection itself because the internal sites work. The wifi access point is attached to a 3Com 4200 switch, with the port set for vlan 2 untagged, vlan 1 tagged. The 4200 has a fiber connection to a 3Com 4900SX fiber switch that acts almost as a router here. The fiber connection is vlan 1 untagged vlan 2 tagged at both ends. The gateway is then attached to a different 4200 (vlan 1 untagged, vlan 2 tagged) that has a similar fiber connection to the 4900SX. vlan 2 has 192.168.8.0/22 IPs, vlan 1 has 10.1.0.0/16 IPs. The 4900SX has an interface for both vlans (10.1.1.1/192.168.8.1), as does the gateway (10.1.1.5/192.168.8.5). There is one dchp server for both vlans on the same switch as the gateway. It chooses a dhcp scope based on the interface used by the 4900sx to forward the dhcp request. There is also a network access list on the 4900sx set to deny all vlan2 traffic to any 10.1.x.x host, with exceptions made for a few servers, including dhcp, 4900sx, and the gateway. I think that about covers it. Any ideas on why internet access would be delayed like this?

  Read the article

• size of bad data on HD windows7

  - by acidzombie24

  While using my external harddrive (NTFS) i had a crc32 error. Now i would like to see how much data is corrupted. If its a few KBs i wont mind but if its a few MB i should consider getting a new harddrive. How can i check using windows7

  Read the article

• Add multi monitor option to remote desktop web access

  - by Eds

  I have a test environment for a remote desktop farm with a connection broker load balancing logins across remote desktop session host servers. All servers are built on Server 2012 R2. Using rd web access, we can access this farm from anywhere. When logging in via web access, you can choose the screen resolution or use full screen. If you have two monitors when selecting full screen, it will always use both your monitors. Does anyone know how to adjust the RDWeb page so that you can choose whether or not to use both your monitors? This option is in the GUI from RDP 6.1 onwards, so I would imagine there is a way to also add it the web access page.

  Read the article

• Lustre - is this bad form?

  - by ethrbunny

  Im going to be consolidating several 'server rooms' into a single installation soon. Part of this effort will be finding a home for 5Tb (and growing) of files / logs. To this end Im looking at Lustre and appreciating its ability to scale. The big vendors want to sell me a $20K SAN to manage this but Im wondering about buying several iSCSI units (like this http://www.asacomputers.com/3U-iSCSI-Solution.html) and using VMs for the OSS machines. This would let me fail-over to cover problems and not require a dedicated system for each OSS. Given articles like this (http://h30565.www3.hp.com/t5/Feature-Articles/RAID-Is-Dead-Long-Live-RAID/ba-p/1422) that talk about how RAID is not keeping up with drive density Im leaning towards more disks with lower capacity each. Again - some akin to the iSCSI array above. Tell me why this is a terrible idea. Do I really need to invest in a PE710 for each OSS/OST?

  Read the article

• How to fix a bad case rattle

  - by C. Ross

  I have a full sized ATX case with several fans, including one on the door/removable side. This fan makes the "door" rattle or vibrate loudly when the fan runs at full speed, such as at startup. I can stop the rattle temporarily by placing my hand on the "door", or pushing an object next to it. Do you have any suggestions for a permanent solution? Note: The "door" in question is a slide out panel with two twist screws at the back to hold it in.

  Read the article

• Why is cleartype so bad at high res?

  - by ULTRA_POROV

  Cleartype is great when displaying small text 10 - 16px HOWEVER when you display something above 20px it start's looking like shit. Just compare it to Photoshop. Photoshop rendering at small size is not very impressive, too blurry. But if you compare it at 20px + Photoshop wins all the time. Cleartype looks jaggy around the edges, almost like there is no cleartype at all. Can this be fixed, or is it just the way cleartype is?

  Read the article

• CodeIgnitor Error 403 Access forbidden

  - by 01010011

  Hi, I extracted CodeIgnitor to XAMPP's htdocs and when I tried to access index.php like this: h t t p://127.0.0.1/ci/index.php I get the following error message: Access forbidden! You don't have permission to access the requested object. It is either read-protected or not readable by the server. Error 403...... How can I troubleshoot this problem?

  Read the article

• How to prevent bad queries from breaking replication?

  - by nulll

  For my personal experience, mysql replication is fragile. I know that there area many things not to do beacuse they could break replication, but we are humans and the error could always occur. So I was thinking... is there a way to enforce mysql replication? Something that prevents queries that are dangerous for the replication to be runt? In other words I'm searching for something that saves replication even if I accidentally run evil queries.

  Read the article

• Linux program unable to access files in group

  - by user1064665

  I'm having trouble configuring things on linux so that a program can access certain files. Let's call it pgm A. It has uid uA and gid gA. In addition, uid uA is listed in /etc/group as a member of group gX. The problem is that pgm A cannot access files for which the uid is root and the gid is gX, but only when pgm A is called from another program, pgm B, which also runs as user uA. If I su as user uA and run pgm A from bash, it has no problem accessing files in group gX. But if another program, pgm B, which also runs as user uA, forks and execs pgm A, pgm A cannot access the files. I've verified that pgm A is indeed running as user uA, group gA, when launched from pgm B. So, if uA is a member of group gX, why can't the program access files which are readable by group gX? It's as if the operating system is ignoring the fact that user uA is also in group gX.

  Read the article

• Restrict access to one SVN repository (overwrite default)

  - by teel

  I'm trying to set up our SVN server so that by default the group developers will have access to all repositories, but I want to override that setting on some certain repositories where I want to allow access only to single defined users (or separate groups) The current configuration is SVN + WebDAV on Apache2. All my repositories are located at /var/lib/svn/ In dav_svn.authz I currently have [/] @developers = rw @users = r Now I want to add one repository (let's call it secret_repo) that would only allow access to one user who is also a member of the developers group.¨ I tried to do [secret_repo:/] * = secret_user = rw Where secret_user is the user I'd like to give access to the repository, but it doesn't seem to work. Currently the server is using Apache's LDAP module to authenticate users from our active directory domain and I'd like to keep it that way if possible. Also I seem to be able to browse all my repos freely with any web browser, which I'd like to block. Second problem is that I have webSVN on the server, which is using Apache's LDAP authentication. Everyone who is a member of our domain can access it, so I'd like to hide this secret_repo from websvn listing. It's configured not with parentPath("/var/lib/svn");. Do I really need to remove that and add every repository separately, except the ones I want to hide?

  Read the article

• Cant access websites internally but can externally, happened all of a sudden on Windows Server 2008

  - by Mike Flynn

  Without any type of change I can access sites from within my server, not even Google. I can access them externally. I have no idea where to start. My internet Lan Settings are set to automatic and not to proxy. Nothing was changed on my end, how can I diagnose this issue? Check my server wasnt using a proxy Cant ping or access websites on my server, and others like google nslookup on my sites causes a refusal

  Read the article

• IIS server unable to access the file path

  - by anil namde

  I have installed web application behind IIS which access the files/directory located on the another machine. Now while developing the application using the Visual Studio 2008 then Developer Web Server it provides when build the site was able to access the location. However when the site is deployed on the IIS its saying Unable to access the file because of insufficient permissions. Can some one please help regarding what could be the issue ? any idea or pointers could be helpful. Thanks,

  Read the article

• IIS server unable to access the file path

  - by anil namde

  I have installed web application behind IIS which access the files/directory located on the another machine. Now while developing the application using the Visual Studio 2008 then Developer Web Server it provides when build the site was able to access the location. However when the site is deployed on the IIS its saying Unable to access the file because of insufficient permissions. Can some one please help regarding what could be the issue ? any idea or pointers could be helpful. Thanks,

  Read the article

• S.M.A.R.T. broken sectors

  - by Jeffrey Vandenborne

  Recently I received my hard drive (LaCie) that I've sent away for warranty, my disk failed, and I used Palimpsest Disk utility to check if anything was wrong in the S.M.A.R.T Status. And it said that there were a few broken sectors. So the next day, I went to the store and told the story. 4 weeks later I actually got my drive back. The first thing I did was plugging it in and starting the disk utility, and weirdly it showed me pretty much the exact same things, even the values of most tests were the same as they were before when my drive broke. The serial number is different though, but it does show a very peculiar value. Now I'm wondering, I'm almost sure it's the exact same drive and it still says I've got broken sectors, does it just say that because it has been cached in the drive somewhere while LaCie DID actually fix it? Or should I run the extended self test (which seems to take hours) first? Also I've tried the smartctl command tool, it says the drive has smart support, but it doesn't show anything, it says that it's enabled, but then it says that it's disabled, picture below The picture of the Disk utility: Thanks in advance

  Read the article

• block access to certain website types

  - by frustrated teacher

  Need to block access to certain website types without listing each URL to block. Students at secondary school are going to porn sites. Need to be able to block all such access without having to list each possible site URL. Having the Content -- Ratings tab set to None for all categories on the ratings files listed on my computers does not prevent access. Unchecking users may access sites with no rating, even with the security settings set to High, still allows the porn sites to come up. If that is checked, then ONLY listed sites can open and students would not be able to do any research via google, for example. I would rather not have to continue checking each computer and blocking sites as they find them.

  Read the article

• How may I start a process without having network access and later allow network access?

  - by Eduardo

  I want to run a process without network access but at a later time give access to the network.

  Read the article

• Is it bad to redirect http to https?

  - by jasondavis

  I just installed an SSL Certificate on my server. I use a web hosting panel called ZPanel that is an open source project. It then set up a redirect for all traffic on my domain on Port 80 to redirect it to Port 443. In other words, all my http://example.com traffic is now redirected to the appropriate https://example.com version of the page. The redirect is done in my Apache Virtual Hosts file with something like this... RewriteEngine on ReWriteCond %{SERVER_PORT} !^443$ RewriteRule ^/(.*) https://%{HTTP_HOST}/$1 [NC,R,L] My question is, are there any drawbacks to using SSL? Since this is not a 301 Redirect, will I lose link juice/ranking in search engines by switching to https? I appreciate the help. I have always wanted to set up SSL on a server, just for the practice of doing it, and I finally decided to do it tonight. It seems to be working well so far, but I am not sure if it's a good idea to use this on every page. My site is not eCommerce and doesn't handle sensitive data; it's mainly for looks and the thrill of installing it for learning. UPDATED ISSUE Strangely Bing creates this screenshot from my site now that it is using HTTPS everywhere...

  Read the article

• Cannot access folder locally, but can remotely

  - by Cylindric

  I'm having a peculiar problem on one of my servers at the moment, which seems to be related to authentication in some way, but I have no idea how to find the root of the problem. I have a folder on the server D:\Somefolder\Logs. If I am connected to the server via an RDP terminal, so essentially "local", I cannot access that folder - I get an access denied. If I am connecting from my machine to it using the share \server\d$\Somefolder\Logs, I can access it. I'm logging in to both machines as the same user. Permissions on the folder seem quite simple, CREATOR OWNER, SYSTEM and Administrators. I am a Domain Admin, and they are in the local "Administrators" group. It is also affecting things like access to SQL Server, so I don't think it's a simple folder-permissions thing. For example, I cannot connect SQL Management Studio to all the local SQL instances using a domain account, but I can if I connect remotely to it.

  Read the article

• Unable to access, make directories (and files) with ftp

  - by Kriem

  I'm having trouble with my new server and accessing its directories. I updated my proftpd.conf with: DefaultRoot / No I'm able to see the root directory of my server. But, trying to access some directories gives different results. For example, I can access /vars but I can't access /home or /root How can I overcome this? This is what my ftp client says after trying to access /root: Server said: /root: No such file or directory Error -125: remote chdir failed This is what my ftp client says after trying to create a new directory in /: Server said: untitled folder: Permission denied Error -140: remote mkdir failed

  Read the article

• Client cannot access my IIS7 web server

  - by Soccerwiz

  I have a Windows 2008 web server on running IIS 7 with about 25 websites. One of those sites is an SaaS application that is accessed constantly throughout the day. However, one particular client keeps getting blocked from my server. They will be using the service, and then all of a sudden they cannot access the program, or any other site on the server. The entire office of 4 users is blocked from accessing anything on the web server. A trace route reveals they get all the way to the server before they are blocked. However, they can access a linux server that is a different VM with a different IP on the same physical server. Also, when they are blocked from their office, they can still access the site from their mobile phone or local Starbucks. They can also occasionally reset the router and gain access to the web server again as they are on a dynamic IP address. I checked IIS and allow all IPs to access the server. There is nothing in the logs the says anything about a user being banned. I really have no idea what is causing this? Could it be a virus on their end? I have even moved the SaaS to a completely new server in a different location, and they were working fine for about a month, and then the problem started occurring again. Are there any hidden blacklists in IIS? Or is it a routing issue on their end?

  Read the article

• Nginx Tornado Combination Causing 502 Bad Gateway Errors

  - by PlaidFan

  We are facing a problem with inconsistent 502 errors and tracking down the reasons has been a very frustrating exercise. We can reproduce the problem by sending several simultaneous requests quickly. The problem is that several is only in the range of 10 to 20 within a 5 seconds (not a typo). So clearly this type of load should be handled easily. We really like the Nginx + Tornado approach but are considering going to a more traditional (e.g. threading) approach because this problem has been very difficult to solve. I was wondering if you a) know how to fix this issue and b) how we can tracked down the culprit(s). The log files simply identify there being a connection refused. We have the same problem as this post: How do I debug a HTTP 502 error? But there is no answer provided on how to solve the problem so I'm hoping you can help because this may be a common issue with this type of setup. Thanks in advance, Paul

  Read the article

• Bad IIS 7.5 performance on webserver

  - by Robert P.

  I have a webpage (ASP.NET 4.0 / MVC 4). On my development machine (i5-2500 3.3 8GB Win7 VS2010 SP1 Fujitsu Esprimo P700) the page performs with 160 requests/sec on devenv webserver on my machine. The page performs with 250 requests/sec on my local IIS 7.5. (uncompiled web) The page performs with 20 requests per second on a 16core 32gb ram production server (Fujitsu RX-300 w2k8 rc2 IIS 7.5). (compiled web) Why? I think it's the IIS configuration but i can't figure out whats the problem. The page runs with 1 worker process on both machines. Web garden is not an option (it helps but the app isnt compatible with)

  Read the article

• Bad HD video deinterlacing processing

  - by Guy Fawkes

  I have Ubuntu 12.04 32-bit with Unity. My system configuration is: CPU: Core 2 Quad Q6600 (2.4 GHz) RAM: 8192 Mb DDR2 Kingston Video: Palit GeForce GTX 260 216 SP, and my screen resolution is 1680x1050. I also have Window 7 Ulitimate installed, and I can see the same files in Media Player Classic without any horizontal lines. I've installed vdpau driver, NVIDIA drivers 304.51, and MPlayer 2 (within SMPlayer). I've disabled "Sync to VBlank" option in CCSM (because in other way, by default, MPlayer process use about 50-60 percents of my processor load), tried to swich between different deinterlace options in SMPlayer, used "-vc ffh264vdpau,ffmpeg12vdpau" (without quotes) parameters for MPlayer, switched to "Ubuntu 2D", but, finally, have no results. Any suggestions? How must I to set up MPlayer?

  Read the article

• can not access dlink 604 set up interface

  - by user36089

  Hello everyone I used dlink-di604 enthernet board as router to share web access. My ISP provides the service base on Ethernet rathern than base on Ethernet pppoe mode. It is manually setup ipv4, subnet mask , DNS, Gateway etc Log in using web user name&password. I use http://192.168.0.2 try to access dlink di604 setup inferface, but failed I call command ipconfig /all Dos shell displayed: Ethernet adapter Local Connection: Physical Address: 00-3c-56-79-19-49 IPv4 address:10.7.8.225 subnet mask: 255.255.255.0 default gate way: 10.7.8.1 DNS servers 10.10.10.10 What is the correct way to access dlink 604 setup interface and set to share web access? Welcome any comment Thanks interdev

  Read the article

• File corruption (bad checksums) in large files copied to VMware guest

  - by AllanA

  In setting up a development lab, I've got a desktop system running ESXi 4.1.0 (free license) on SATA RAID 0 (already purchased and configured when I started this job; I'm open to hardware input as it pertains to my problem.) Its guests so far include two Win2008 Server R2 64-bit VMs and on Ubuntu 10.04 64-bit VM. I'm installing onto the Windows servers. We've been copying off some fairly large files (over a gigabyte) for an installation, hoping to install more quickly from a (virtual) hard drive than from the network for from BD-ROM. The problem is that they keep coming up with different checksums from the originals. The file sizes are the same, but md5sum reports different numbers (and so does the installer, as it refuses to continue when the checksums don't match.) I've tried copying directly from the BD-ROM (attaching the OS drive to the host system's physical drive). I've tried copying the large files onto a co-worker's Windows machine from his Blu-Ray drive; when I do that, the checksums match. But when I copy from his machine to the VM guest over a network share, the checksums no longer match. Thinking this meant a corrupt destination drive, I deleted it in vSphere and added another freshly created drive. The problem persists. I'm not sure what to try next.

  Read the article

< Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >