Search Results

Search found 2630 results on 106 pages for 'sergey p aka azure'.

Page 80/106 | < Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

• chef clients behind firewall

  - by tec

  I am currently learning about chef. What I understood so far: I have to install chef-server on an own server or use the hosted chef. I have to install chef-client on the servers that I want to manage aka nodes (manually or using knife bootstrap). I installed several chef tools on my own PC that I can use to manage the nodes, e.g. knife. Now in my case the specialty is that the nodes are behind a firewall/load balancer/proxy. The nodes can access servers on the outside via NAT (http works and I can configure chef-specific hosts to work as well). However they can only be contacted from the outside via a ssh tunnel. There is really much documentation about chef available but I did not find an answer to these questions: When using knife, is it enough when I set up a ssh tunnel manually on my own PC or does the chef server need to contact the nodes? When using knife, can I configure it to setup a ssh tunnel automatically? When using the chef server web ui can I configure it to connect to the nodes via ssh tunnel or do I need a setup where I setup the tunnel myself e.g. using monit? Is this even possible with hosted chef? Instead of using knife or the web ui: Can I issue the same management commands directly on the nodes using chef-client? What solution would you recommend? Thanks a lot for taking your time to help and answering one or more of these related questions

  Read the article

• Performance of Virtual machines on very low end machines

  - by TheLQ

  I am managing a few cheap servers as my user base isn't large enough to get much more powerful servers. I also don't have the money lying around to invest in a server to prepare for the larger user base. So I'm stuck with the old hardware I have. I am toying with the idea of virtualizing all the current OS's with most likely VMware vSphere Hypervisor (AKA ESXi) Xen (ESXi has too strict of an HCL, and my hardware is too old). Big reasons for doing so: Ability to upgrade and scale hardware rapidly - This is most likely what I'll be doing as I distribute services, get a bigger server, centralize (electricity bills are horrible), distribute, get a bigger server, etc... Manually doing this by reinstalling the entire OS would be a big pain Safety from me - I've made many rookie mistakes, like doing lots of risky work on a vital production server. With a VM I can just backup the state, work on my machine, test, and revert if necessary. No worries, and no OS reinstallation Safety from other factors - As I scale servers might go down, and a backup VM can instantly be started. Various other reasons. However the limiting factor here is hardware. And I mean very depressing hardware. The current server's run off of a Pentium 3 and 4, and have 512 MB and 768 MB RAM respectively (RAM can be upgraded soon however). Is the Virtualization layer small enough to run itself and a Linux OS effectively? Will performance be acceptable (50% CPU overhead for every operation isn't acceptable)? Does it leave enough RAM for the Linux OS? Is this even feasible?

  Read the article

• Has anyone used products by StorSimple? [closed]

  - by AlamedaDad

  Their products are storage systems similar to NetApp, but their "hook" is they provide automated tiered storage with the third tier being Cloud providers like Amazon and Azure. They have an interesting story in which they provide primary SAN/iSCSI storage to VMWare and Exchange and at the same time do snaphots to the Cloud. This provides a possible DR option if you have a second system at an alternate location. I was impressed, but I've never heard of them so I'm looking for input and advise on the product. Thanks in advance...

  Read the article

• ServerName not working in Apache2 and Ubuntu

  - by CreativeNotice

  Setting up a dev LAMP server and I wish to allow dynamic subdomains, aka ted.servername.com, bob.servername.com. Here's my sites-active file <VirtualHost *:80> # Admin Email, Server Name, Aliases ServerAdmin [email protected] ServerName happyslice.net ServerAlias *.happyslice.net # Index file and Document Root DirectoryIndex index.html DocumentRoot /home/sysadmin/public_html/happyslice.net/public # Custom Log file locations LogLevel warn ErrorLog /home/sysadmin/public_html/happyslice.net/log/error.log CustomLog /home/sysadmin/public_html/happyslice.net/log/access.log combined And here's the output from sudo apache2ctl -S VirtualHost configuration: wildcard NameVirtualHosts and default servers: *:80 is a NameVirtualHost default server happyslice.net (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost happyslice.net (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost happyslice.net (/etc/apache2/sites-enabled/happyslice.net:5) Syntax OK The server hostname is srv.happyslice.net. As you can see from apache2ctl when I use happyslice.net I get the default virtual host, when I use a subdomain, I get the happyslice.net host. So the later is working how I want, but the main url does not. I've tried all kinds of variations here, but it appears that ServerName just isn't being tied to the correct location. Thoughts? I'm stumped. FYI, I'm running Apache2.1 and Ubuntu 10.04 LTS

  Read the article

• Rsync: General file/folder synchronization

  - by Rey Leonard Amorato

  I have a file server, which is in-charge of pulling a folder tree from multiple workstations on a daily basis. My current method for this is by using rsync, (which works pretty well provided directory names and/or files remain the same) however, when files are renamed or moved about within subdir1, rsync will copy them over to the server, creating duplicates. I have to manually find and delete extraneous files/folders that had been left on the server during previous syncs. Note that I cannot use rsync's --delete flag because any sync from a workstation will then mirror that particular folder tree, instead of merging them to the server. Visual diagram: Server: Workstation1 Workstation2 Workstation(n) Folder* Folder* Folder* Folder* -subdir1 -subdir1 -subdir1 -subdir(n) -file1 -file1 -file2 -file(n) -file2 -file(n) Is there a simple script (preferably in bash, nothing fancy) that can accomplish the deletion of the extraneous files/folders in the event a file is renamed or moved to a different subdir? Is there a different program, much like rsync that can accomplish this task autonomously and in a much simpler manner? I have looked at unison, but I did not like the fact that it keeps a local database for the syncing info. Any tips at all as to how I am supposed to tackle this? Thank you in advanced for your help. EDIT: I have tried unison just recently and I can safely say it is out of the question now. unison is a bi-directional synchronization tool and from my testing, it mirrors the files existing on the server to all workstations. - This is unwanted. preferably, i would want files/folders to stay within their respective workstations and just merge to the server. AKA uni-directional sync; but with renames/moves propagated to the server. I might have to look into Git/Mercurial/Bazaar as mentioned by kyle, but still unsure if they are fit for the job.

  Read the article

• Allow access from outside network with dmz and iptables

  - by Ivan

  I'm having a problem with my home network. So my setup is like this: In my Router (using Ubuntu desktop v11.04), I installed squid proxy as my transparent proxy. So I would like to use dyndns to my home network so I could be access my server from the internet, and also I installed CCTV camera and I would like to enable watching it from internet. The problem is I cannot access it from outside the net. I already set DMZ in my modem to my router ip. My first guess is because i'm using iptables to redirect all inside network to use squid. And not allow from outside traffic to my inside network. Here is my iptables script: #!/bin/sh # squid server IP SQUID_SERVER="192.168.5.1" # Interface connected to Internet INTERNET="eth0" # Interface connected to LAN LAN_IN="eth1" # Squid port SQUID_PORT="3128" # Clean old firewall iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X # Load IPTABLES modules for NAT and IP conntrack support modprobe ip_conntrack modprobe ip_conntrack_ftp # For win xp ftp client #modprobe ip_nat_ftp echo 1 > /proc/sys/net/ipv4/ip_forward # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT ACCEPT # Unlimited access to loop back iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # Allow UDP, DNS and Passive FTP iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT # set this system as a router for Rest of LAN iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT # unlimited access to LAN iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT # DNAT port 80 request comming from LAN systems to squid 3128 ($SQUID_PORT) aka transparent proxy iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT # if it is same system iptables -t nat -A PREROUTING -i $INTERNET -p tcp --dport 80 -j REDIRECT --to-port $SQUID_PORT # DROP everything and Log it iptables -A INPUT -j LOG iptables -A INPUT -j DROP If you know where did I miss, please advice me. Thanks for all your help and I really appreciate it.

  Read the article

• Proper 16:9 video size for non-HD 4:3 video (for youtube/vimeo)

  - by Xeoncross

  Since High Definition video came out on all the online sites it has changed the default aspect ratio of the player from 4:3 to 16:9. This means that for people posting SD video you have to resize some of your videos to get them to fit right. For example, NTSC DVD quality (aka 480i/p) is 720x480 pixels (width x height). However, low-end High Definition (720i/p) is 1280x720. Resolution Chart Anyway, now that the video players are built for HD you will find that uploading standard quality videos will result in videos that are "letter boxed" which means they have extra black bars on the top and bottom (or sides). Correct me if I'm wrong, but in order to get a 720x480 video to fit a box that is designed for HD the best practice would be to crop some of it off so that it fits as 720x404 since: 16/9 = 1.78 (1.7777777777778) 720/405 = 1.78 405x1.78 = 720.9 The same would stand for 640x480 (old TV quality) video that would need to be 640x360 correct? I'm asking because I'm not sure about all this and whether this is the proper way to fix these letter-boxing/display problems.

  Read the article

• Copying email with qmail and Plesk

  - by Greg

  I need to keep a copy of all outgoing and incoming email (for a single domain if possible) using qmail or Plesk. I can't recompile qmail, so qmailtap is out of the question, as is setting QUEUE_EXTRA in extra.h. I'm pretty sure it should be possible with Plesk's mailmng utility, aka Mail Handlers but I'm having trouble getting them to work. I've registered 2 hooks: incoming hook ./mailmng --add-handler --handler-name=incoming --recipient-domain=example.com --executable=/xxx/incoming.sh --context=/xxx/incoming/ --hook=before-local incoming.sh #!/bin/bash # The email is passed on stdin - grab it to a variable e=`cat -` # $1 = context (/xxx/incoming) # $3 = recipient ([email protected]) # Create /xxx/incoming/[email protected] mkdir -p $1$3 # Save the email to /xxx/incoming/[email protected]/0123456789.txt echo "$e" > $1$3/`date +%s%N`.txt # Echo PASS to stderr echo 'PASS' >&2 # Echo the email to stdout echo "$e" outgoing hook # ./mailmng --add-handler --handler-name=outgoing --sender-domain=holidaysplease.com --executable=/xxx/outgoing.sh --context=/xxx/outgoing/ --hook=before-remote The outgoing.sh file is the same as incoming.sh, except replace $3 (recipient) with $2 (sender). The incoming hook does work, but saves 2 copies of each email - one before and one after SpamAssassin has run. The outgoing hook doesn't seem to get called at all. So finally, my questions are: How can I make the incoming hook save only a single copy (preferably after SpamAssassin has run)? How can I get the outgoing hook to work?

  Read the article

• Windows Bluescreen - atikmpag.sys

  - by Mochan

  Information Name: atikmpag.sys bluescreen (BSOD or BlueScreen of Death) Error code: 0x00000116 Appears when: Playing games, watching videos Can be reproduced: Yes Cause: Graphics Card is the main assumption System Specifications Before we begin - I will inform you of my specifications. OS: Windows 7 x64 Home Edition Model: Dell Inspiron 15R Special Edition (aka Inspiron 7520) (Add 2GB of RAM to the model linked) Hard Drive: 1TB CPU: Intel Quad-Core i7 Sandy Bridge (I think) Processor at 2.10GHz (I think it can be clocked to 3GHz?) RAM: 6GB (I think 1 x 4GB and 1 x 2GB) Display: 15.6" HD (1366x768) Graphics: AMD Radeon HD 7500M 2GB Details So now that you know some basics about my computer, I'll get to the problem. Being an Ubuntu user I hardly use Windows, but occasionally I do. Like to run Skyrim and other games incompatible with Linux and WINE. The new Sims 3 Seasons patch is also now not supported. When playing these two games and other ones, theoretically. I have also heard others saying that while watching HD movies and video series it also happens. While watching the bluescreen as it happens, I see it is the 'atikmpag.sys' error. I have not installed much and nothing significant. I think I have downloaded Skyrim, Firefox and The Sims 3. I haven't done much more... since Ubuntu is definitely the best in comparison! (No hate, just a joke :P). I can reproduce it easily (just by running a game for less than a minute). It is always there each time, but it's never at a specific time or anything. So far I have found that it may be caused by lack of power to the graphics card, or it may be damaged or fried. Since I've had the computer for a mere 4 months (and have had other problems with it also). I have contacted Dell but they are useless beyond belief. Anyone with any information, solutions or details are encouraged to share your knowledge, as it would be immensely appreciated.

  Read the article

• Fast swapping of production and staging in IIS

  - by Nathan Ridley

  I'm using IIS 7 on my own dedicated server. Let's say I have two web applications. One points to folder A, and one points to folder B. The first is used for production and the second is for staging. If I want to set up a scenario whereby I upload my aplication to staging, make sure everybody's happy, then swap the folders that each web application points at, thereby putting "staging" live and making the production environment the new staging environment, what's a good way to do this? I know Microsoft themselves use this methodology on their Azure platform and I've seen it used elsewhere too. How can I do it on my server with IIS7?

  Read the article

• Remote assistance from Remote Desktop sessions: unable to control

  - by syneticon-dj

  Since Remote Control (aka Session Shadowing) is gone for good in Server 2012 Remote Desktop Session hosts, I am looking for a replacement to support users in a cross-domain environment. Since Remote Assistance is supposed to work for Remote Desktop Sessions as well, I tried leveraging that for support purposes by enabling unsolicited remote assistance for all Remote Desktop Session Hosts via Group Policy. All seems to be working well except that the "expert" seems to be unable to actually excercise any mouse or keyboard control when the remote assistance session has been initiated from a Remote Desktop session itself. Mouse clicks and keyboard strokes from the "expert" session (Server 2012) seem to simply be ignored even after the assisted user has acknowledged the request for control. I would like to see this working through RD sessions for the support staff due to a number of reasons: not every support agent would have the appropriate client system version to support users on a specific terminal server (e.g. an agent might have a Windows Vista or Windows 7 station and thus be unable to offer assistance to users on Server 2012 RDSHs) a support agent would not necessarily have a station which is a member of the specific destination domain (mainly due to the reason that more than a single domain's users are supported) what am I missing?

  Read the article

• Melting plastic around DC-in jack in laptop

  - by Ove

  I recently noticed that the plastic around the DC-in jack of my laptop was warped (melted) a little bit. Since I noticed, I have done some experiments, and saw that the metal tip of the charger heats up very much when I am gaming, or performing CPU-intensive work (it's so hot that i can't hold it between my fingers). When I am using Windows normally (web browsing, music, video), the tip is not hot. I tried using another charger from a compatible laptop, but its metal tip overheated as well, so the problem is not caused by the charger. I have been using this laptop for gaming for 1.5 years and I never had this problem. When gaming I always use a laptop cooler. Dust is not the problem (i cleaned out the dust), and the CPU and GPU temperatures are not higher than when I got the laptop. The only thing that is excessively hot is the charger tip. Because I bought my laptop from the USA, sending it to warranty and back would cost more than the laptop's value, so I need to fix it myself. I have googled around, and I saw that the problem might be the DC-in jack that is located on the motherboard of the laptop. I plan to take the laptop apart and see if it has become loose, and soldering it in place if it has. My questions for you are: Did anyone deal with this problem in the past? Did anyone manage to fix it? Is the DC-in jack the culprit in this case? Or is it possible for the problem to be caused by another part on the motherboard? Is there any way I can check the DC-in jack with a multimeter? What should I measure (resistance, etc)? EDIT: My laptop is a Sager NP5135 (aka Clevo B5130M). I also posted on NBR, including some pictures: link

  Read the article

• Looking for an application to record audio and video on a linux "embedded" device

  - by Luke404

  I am working with a linux x86 device with limited CPU resources (as a prototype we just use a pentium-m netbook). We'd like to record video from one V4L2 device (we'll probably end up using just USB Video Class devices like all modern webcams) and one audio stream from an ALSA source. The thing will not have screen and keyboard, and obviously no X11 environment. Goals are: do as little work as possible to cope with little cpu resources - for example I'd like to record video in the native MJPEG I get out of the UVC devices encoding audio to MPEG3 Layer-2 (aka mp2) is ok since it let us save a lot of space (compared to raw pcm samples) and does use little cpu power I don't mind loosing some video frames here and there (UVC devices do that) as long as I can get audio and video streams syncronized not require user input to start the thing (a python script takes care of initialization, startup, shutdown, etc...) be able to open the resulting files for postprocessing without too much effort (ie, if mplayer or vlc can play it, it's fine) So far the only app I found that could be started from command line and record V4L2 video + ALSA audio is mencoder but I'm having some difficulties with it. It should be able to do that but I cannot record audio and video together - just one of the two. And if I use two different processes to record to two different files I have no means to get them in sync (audio is more or less always correct, but video framerate will vary over time and it seems to lack timestamps to correctly play it back to the correct time). Long story short, how do you record an unconverted MJPEG stream (from an UVC device) and an audio stream (from an ALSA device, possibly encoding to any standard format) using a command line tool, to a single file (MPEG or any other container), keeping audio and video in sync?

  Read the article

• Windows 7 taskbar groups to use vertical menus only, not thumbnails?

  - by Justin Grant

  I frequently have 10 or more windows of the same application (e.g. Outlook, Word, IE, etc.) open at one time. Windows 7's new taskbar grouping thumbnail feature shows a preview of open windows (aka thumbnails) when you single-click on the taskbar group for that application. But when I have over 10 windows open (more thumbnails than will fit horizontally on my screen), Windows reverts to a vertical menu. This is disconcerting since I need to train myself to deal with two separate behaviors and can never anticipate what I'm going to see when I click on a taskbar group. Furthermore, I find the thumbnails more difficult to visually scan through (vs. the vertical menu) because only 1-2 words of each window's title are shown. Typically that's not enough text to disambiguate and help me find the right window. I'd like to force Windows 7's taskbar grouping to always show a vertical menu (like in XP) instead of sometimes showing thumbnail previews and sometimes showing a vertical menu. Anyone know how (whether?) this can be done? UPDATE: BTW, I'm running the RTM version (build 7600) of Windows 7. There are apparently other solutions out there which work on earlier builds, but which don't work on the RTM build.

  Read the article

• How do I ensure a process is running, even if it kills itself? (it needs to be restarted then)

  - by le_me

  I'm using linux. I want a process (an irc bot) to run every time I start the computer. But I've got a problem: The network is bad and it disconnects often, so I need to manually restart the bot a few times a day. How do I automate that? Additional information: The bot creates a pid file, called bot.pid The bot reconnects itself, but only a few times. The network is too bad, so the bot kills itself sometimes because it gets no response. What I do currently (aka my approach ;) ) I have a cron job executing startbot.rb every 5 minutes. (The script itself is in the same directory as the bot) The script: #!/usr/bin/ruby require 'fileutils' if File.exists?(File.expand_path('tmp/bot.pid')) @pid = File.read(File.expand_path('tmp/bot.pid')).chomp!.to_i begin raise "ouch" if Process.kill(0, @pid) != 1 rescue puts "Removing abandoned pid file" FileUtils.rm(File.expand_path('tmp/bot.pid')) puts "Starting the bot!" Kernel.exec(File.expand_path('./bot.rb')) else puts "Bot up and running!" end else puts "Starting the bot!" Kernel.exec(File.expand_path('./bot.rb')) end What this does: It checks if the pid file exists, if that's true it checks if kill -s 0 BOT_PID == 1 (if the bot's running) and starts the bot if one of the two checks fail/are not true. My approach seems to be quite dirty so how do I do it better?

  Read the article

• CentOS Existing host to new host with all data/files

  - by ganesh

  Good noon. Our small startup management decided to move our production server from existing provider to azure. We have centOS on both. It is for classified's related site, considerable amount of data and ~thousands users with their disc space quota. This is our first time moving our servers. I need your Guidance and suggestions on these. 1) How to migrate the mysql db (dump OR slave OR copy filesystem)? 2) How to manage the emails during the downtime. 3) Manage the files 4) How to security/Firewall check list for the new system 5) IP/DNS related Checklist 6) Anything that I missed out!. Since first time, planning to be more cautious. Any reference documents Highly appreciated. Thank you all!.

  Read the article

• Bypassing SQUID on freebsd with PF

  - by epema

  I have PF+SQUID31 on FREEBSD-9.0, and I want to have some hosts(aka goodguys) to bypass the proxy, so that torrents are not logged. Also, I am not sure about transparent. It means that I dont have to configure proxy settings on the client side right? I have tried doing a redirect no rdr on $int_if inet proto {tcp,udp} from 192.168.1.233/32 to any However, no luck :( Here is a quick look of my conf files: SQUID /usr/local/etc/squid/squid.conf http_port 192.168.1.1:8080 transparent RC /etc/rc.conf: gateway_enable="YES" pf_enable="YES" pf_rules="/usr/local/etc/pf.conf" pflog_enable="YES" squid_enable="YES" I have squid31 installed from ports with SQUID_PF "Enable transparent proxying with PF" on PF /usr/loca/etc/pf.conf: int_if="re0" ext_if="bge0" localnet="{ 192.168.1.0/24 }" table <goodguys> const { "192.168.1.219", "192.168.1.233" } set block-policy drop set skip on lo0 scrub in all fragment reassemble scrub out all random-id max-mss 1440 block in on $ext_if pass out on $ext_if keep state block in on $int_if pass in on $int_if inet proto tcp from $int_if:network to $int_if port 8080 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 21 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 22 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 53 keep state pass in on $int_if inet proto tcp from $int_if:network to any port { smtp, pop3 } keep state pass in on $int_if inet proto icmp from $int_if:network to $int_if keep state pass out on $int_if keep state What lines should I add in conf files? I am assuming that the problem is on the firewall(pf).

  Read the article

• Windows Server Task Scheduler: Running scheduled executable fail-safe?

  - by Mikael Koskinen

  I have an executable which I've scheduled to run once in every five minutes (using Window's built-in Task Scheduler). It's crucial that this executable is run because it updates few time critical files. But how can I react if the virtual server running the executable goes down? At no point there shouldn't be more than 15 minutes break between the runs. As I'm using Windows Server and its Task Scheduler, I wonder is it possible to create some kind of a cluster which automatically handles the situation? The problem is that the server in question is running on Windows Azure and I don't think I can create actual clusters using the virtual machines. If the problem can be solved using a 3rd party tool, that's OK too. To generalize the question a little bit: How to make sure that an executable is run once in every 5 minutes, even if there might be server failures?

  Read the article

• Why do my proxy settings keep changing?

  - by tjrobinson

  I am running Windows 7 and a few times a day the "Use a proxy server for your LAN (These settings will not apply to dial-up of VPN connections)." under "Local Area Network (LAN) Settings" checkbox becomes checked seemingly on it's own. Am I pressing some kind of hidden keyboard shortcut accidentally? What sort of applications might alter this setting and why? Unfortunately as this is a developer box, there's a lot of stuff that could be interfering, e.g. Visual Studio 2010, Windows Azure SDK and various browsers. Has anyone else come across this?

  Read the article

• MySql calculate number of connections needed

  - by Udi I

  I am trying to figure my needs regarding web service hosting. After trying Azure I have realized that the default MySql they provide (through a third party) limits the account to 4 connections. You can then upgrade the account to 15, 30 or 40 connections (which is quite expensive). Their 15 connections plan is descirbed as: "Excellent choice for light test and staging apps that need a reliable MySQL database". I have 2 questions: if my application is a web service which needs to preform ~120k Queries a day (Normal/BELL distribution) and each query is ~150ms(duration)/~400ms(fetch), how many connection do I need? If instead of using cloud computing, I will choose a VPS, how many connections will I be able to handle on a 1GB 2 cores VPS? Thank you!

  Read the article

• The Wifi is working fine but no internet connection in Windows 8 [migrated]

  - by Ali

  I'm currently having a Problem with my msi GT70 laptop. my laptop is running windows 8 and yesterday it requested a Restart to Update. after the Restart and the update I tried to surf the net through google chrome, the WiFi connection is perfect but the page I tried to access is not loading at all, after a while it shows failure to load page. I disabled and reenabled the WiFi chip through the device manager but still no internet connection. I uninstalled and reinstalled the drivers, still no internet. I updated the Driver of the wifi, still no internet, I even went to Wifi configuration and tried to change the DNS and reset it back to automatically, still no Luck.. I'm really lost I don't know what to do, I don't want to go deep and play with Laptop DNA "aka: registry file" and screw things up. I really appreciate any help in this matter. thanks in advance. Note: I tried to access many pages but no luck. I even tried Firefox, Opera, even ie still no luck. The internet is working fine on my tablet and cellphone, except for the Laptop.

  Read the article

• Route return traffic to correct gateway depending on service

  - by Marnix van Valen

  On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

  Read the article

• Is it possible to use WebMatrix with pure IIS?

  - by Mike Christensen

  I'd like to check out WebMatrix for publishing our site to IIS automatically (right now, I have to zip it up, copy it out, Remote Desktop into the server, unzip it, etc). However, every example I can find on how to setup WebMatrix involves Azure, or using a .publishsettings file that you'd get from your hosting provider. I'm curious if I can publish to a normal, every day IIS server running on Windows Server 2008. So far, all I've done to the IIS server is install Web Deploy, which I believe is the protocol that WebMatrix uses to publish. When I enter the Remote Site Settings screen, I select Enter settings. I select Web Deploy as the protocol, type in my NT domain credentials (I'm an Admin on that server). I put in the site URL for the Site Name and Destination URL. When I click Validate Connection, I get: Am I doing something wrong, or is this just not possible to do?

  Read the article

• IIS: Content-Length 0 for CSS, Javascript and Images

  - by Adrian Grigore

  After a clean re-installation of my Windows 7 system, I can't get IIS 7 to properly deliver any static content. Dynmic content (ASPX pages and content served by ASP.NET MVC controllers) works fine, but static files such as CSS, Javascript and Images give me a 200 OK status code and a Content-Length of 0. The problem occurs with all web sites on my server, even a brandnew ASP:NET MVC template project with no changes. It also occurs with both Firefox and IE 8. What could possibly be the problem? Note that I also installed the latest Windows Azure SDK, perhaps that messed up some settings. But I don't know how to proceed with for troubleshooting this.

  Read the article

• Pushing Windows Store apps silently

  - by seagull

  As part of a requirement I have been issued, I seek the ability to push apps from the Windows Store (.appx) to remote users. The framework surrounding the data transmission is sorted; What I need to know is if there is a script that can be sent out along with a URI or the package proper to facilitate installation on the user-side of the Windows Store app. I am well aware that numerous guides exist from Microsoft on pushing out Line-of-Business (LOB) (AKA Enterprise) applications -- that is, apps that have been developed in-house and are not for the consumption of the Windows store. This is inappropriate for my requirement, however; the customer wants their clients to receive apps that appear currently on the Windows Store, and for them to be installed in a silent manner. I've seen this guide; http://blogs.technet.com/b/keithmayer/archive/2013/02/25/step-by-step-deploying-windows-8-apps-with-system-center-2012-service-pack-1.aspx, which details doing exactly this, but it is only applicable to machines that are administered by a system running Windows Server 2012 R2 with the 'System Center 2012' bundle installed. The systems I target are considerably more decentralised than this, making this guide inappropriate. I have a hunch that Microsoft have deliberately designed the Windows Store to be this way, but I figured I ought to ask around before I resign myself to the requirement. Much obliged

  Read the article

< Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >