Search Results

Search found 24609 results on 985 pages for 'private ip'.

Page 807/985 | < Previous Page | 803 804 805 806 807 808 809 810 811 812 813 814  | Next Page >

• dhcp-snooping option 82 drops valid dhcp requests on 2610 series Procurve switches

  - by kce

  We are slowly starting to implement dhcp-snooping on our HP ProCurve 2610 series switches, all running the R.11.72 firmware. I'm seeing some strange behavior where dhcp-request or dhcp-renew packets are dropped when originating from "downstream" switches due "untrusted relay information from client". The full error: Received untrusted relay information from client <mac-address> on port <port-number> In more detail we have a 48 port HP2610 (Switch A) and a 24 port HP2610 (Switch B). Switch B is "downstream" of Switch A by virtue of a DSL connection to one of Switch A ports. The dhcp server is connected to Switch A. The relevant bits are as follows: Switch A dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 168 interface 25 name "Server" dhcp-snooping trust exit Switch B dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 interface Trk1 dhcp-snooping trust exit The switches are set to trust BOTH the port the authorized dhcp server is attached to and its IP address. This is all well and good for the clients attached to Switch A, but the clients attached to Switch B get denied due to the "untrusted relay information" error. This is odd for a few reasons 1) dhcp-relay is not configured on either switch, 2) the Layer-3 network here is flat, same subnet. DHCP packets should not have a modified option 82 attribute. dhcp-relay does appear to be enabled by default however: SWITCH A# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0 SWITCH B# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 40156 0 0 0 And interestingly enough the dhcp-relay agent seems very busy on Switch B, but why? As far as I can tell there is no reason why dhcp requests need a relay with this topology. And furthermore I can't tell why the upstream switch is dropping legitimate dhcp requests for untrusted relay information when the relay agent in question (on Switch B) isn't modifying the option 82 attributes anyway. Adding the no dhcp-snooping option 82 on Switch A allows the dhcp traffic from Switch B to be approved by Switch A, by virtue of just turning off that feature. What are the repercussions of not validating option 82 modified dhcp traffic? If I disable option 82 on all my "upstream" switches - will they pass dhcp traffic from any downstream switch regardless of that traffic's legitimacy? This behavior is client operating system agnostic. I see it with both Windows and Linux clients. Our DHCP servers are either Windows Server 2003 or Windows Server 2008 R2 machines. I see this behavior regardless of the DHCP servers' operating system. Can anyone shed some light on what's happening here and give me some recommendations on how I should proceed with configuring the option 82 setting? I feel like i just haven't completely grokked dhcp-relaying and option 82 attributes.

  Read the article

• postfix + opendkim not signing correctly. how to debug this?

  - by Dean Hiller

  EDIT: I did get a little further but all posts on my search say permissions are wrong or regenerate key but I fixed that to be 644 as well as owned by DKIM AND I keep regenerating the key but it is not helping. My latest error now is this Apr 21 21:19:12 Sniffy opendkim[8729]: BB5BF3AA66: dkim_eom(): resource unavailable: d2i_PrivateKey_bio() failed Apr 21 21:19:12 Sniffy postfix/cleanup[8627]: BB5BF3AA66: milter-reject: END-OF-MESSAGE from localhost[127.0.0.1]: 4.7.0 resource unavailable; from=<[email protected]> to=<[email protected]> proto=SMTP helo=<abcs.com> I am looking for a way to simply debug this(don't necessarily need the answer but a way to get logs from opendkim would be good). If I stop opendkim, I see postfix log connection refused which is good. but when I send mail with opendkim started, I see no logs whatsoever. I even add the "LogWhy Yes" line to my opendkim.conf file as well and still see no logs there. Since I see opendkim running under user opendkim, I changed the owner of /etc/opendkim/* and /etc/opendkim and /etc/opendkim.conf all to opendkim user. I am running on ubuntu. My opendkim.conf file is # Log to syslog Syslog yes # Required to use local socket with MTAs that access the socket as a non- # privileged user (e.g. Postfix) UMask 002 # Sign for example.com with key in /etc/mail/dkim.key using # selector '2007' (e.g. 2007._domainkey.example.com) #Domain example.com Domain sniffyapp.com #KeyFile /etc/mail/dkim.key KeyFile /etc/opendkim/keys/sniffyapp.com/default.private #Selector 2007 Selector default # Commonly-used options; the commented-out versions show the defaults. #Canonicalization simple Mode sv #SubDomains no #ADSPDiscard no Socket inet:8891:localhost ExternalIgnoreList refile:/etc/opendkim/TrustedHosts InternalHosts refile:/etc/opendkim/TrustedHosts LogWhy Yes I of course have these lines added to main.cf in postgres smtpd_milters = inet:127.0.0.1:8891 non_smtpd_milters = $smtpd_milters milter_default_action = accept

  Read the article

• FTP timing out after login

  - by Imran

  For some reasons I cant access any of my accounts on my dedicated server via FTP. It simply times out when it tried to display the directories. Heres a log from FileZila... Status: Resolving address of testdomain.com Status: Connecting to 64.237.58.43:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [TLS] ---------- Response: 220-You are user number 3 of 50 allowed. Response: 220-Local time is now 19:39. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER testaccount Response: 331 User testaccount OK. Password required Command: PASS ******** Response: 230-User testaccount has group access to: testaccount Response: 230 OK. Current restricted directory is / Command: SYST Response: 215 UNIX Type: L8 Command: FEAT Response: 211-Extensions supported: Response: EPRT Response: IDLE Response: MDTM Response: SIZE Response: REST STREAM Response: MLST type*;size*;sizd*;modify*;UNIX.mode*;UNIX.uid*;UNIX.gid*;unique*; Response: MLSD Response: ESTP Response: PASV Response: EPSV Response: SPSV Response: ESTA Response: AUTH TLS Response: PBSZ Response: PROT Response: 211 End. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Response: 227 Entering Passive Mode (64,237,58,43,145,153) Command: MLSD Response: 150 Accepted data connection Response: 226-ASCII Response: 226-Options: -a -l Response: 226 18 matches total Error: Connection timed out Error: Failed to retrieve directory listing I have restarted the FTP service serveral times but still It doesnt loads. I only have this problem when my server is reaching it peak usage which is still only 1.0 (4 cores), 40% of 4GB ram. The ftp connections isnt maxed out because only me and my colleague have access to FTP on the server.

  Read the article

• Launching firefox on remote server causes local firefox to start instead

  - by terdon

  Right, this is strange. I am connecting from my laptop (LMDE) to a remote host (SUSE linux enterprise) using ssh -X. I want to launch a firefox instance running on the remote server so I can have access to webpages on a private network. User@RemoteMachine $ which -a firefox /usr/bin/firefox User@RemoteMachine $ /usr/bin/firefox --version Mozilla Firefox 2.0.0.2, Copyright (c) 1998 - 2007 mozilla.org User@LocalMachine $ which -a firefox /usr/bin/firefox User@LocalMachine $ /usr/bin/firefox --version Mozilla Firefox 14.0.1 Now, if firefox is not running on the local machine, everything goes as expected and executing firefox on the remote machine causes a firefox (v 2.0) window running on the remote machine to show up. However, if firefox is running on the local machine a second window of firefox 14.0.1 running on the local machine appears. I have checked top in both machines. In the 2nd case, a firefox process briefely appears on the remote machine and then disappears when the local version of firefox is launched. My questions are the following: What gives? How/why can firefox connect to its existing instance on the local machine? The remote machine appears to have access to the local machine. It, in fact, appears to have the right to execute programs on my local machine. Am I missing something or is this just weird? Is this not a security risk?

  Read the article

• Windows 7 extremely slow login, exchange performance, printer enumeration, etc...

  - by Jeff

  Background: I have a fresh copy of Windows 7 Professional x64 on a Dell Latitude E6500. The laptop has 8GB RAM, 250GB drive, and all Intel peripherals (net/wifi/graphics). All available Windows updates, as well as hardware drivers are installed. The IT folks where I work joined the computer to our Windows 2003-based Active Directory domain. There are no errors in any logs that we've looked at, and Group Policy templates appear to have applied properly. Problem: Every time I turn on or reboot the computer, it takes between 2 to 10 (all times are actual) minutes after successfully typing my username/password to get to my desktop. My login script does not always run. Sometimes I get a black screen, and a couple of minutes later the login script will pop up and take up to 10 minutes to complete. I can get around this by hitting cntrl-shift-esc and running explorer.exe from the Task Manager. The login script continues to hang, but I can minimize it and go on about my business. Either way, it generally throws errors prior to completing. I often get slow or failed connectivity to Exchange via Outlook. When I bring up printer dialogs, they take several minutes to populate, and block the calling app while doing so. Copies to SMB shares are very slow. On my home network, everything works fine. On both the work network and home network, I can use remote internet resources just fine. Web pages pull up, remote VPN's are fine, I can max out bandwidth on SpeakEasy Speed Test. I can get almost max bandwidth transferring FTP/HTTP over a LAN. Another symptom of the problem is that when I first log in, the work network shows as "Identifying" for a long time in the Network and Sharing Center, and will often then change to the name of the work domain, but say "Unauthenticated Network". Note that this computer previously ran Windows Vista with none of these problems. Attempts to Fix: Installed the Win7 admin pack Uninstalled/reinstalled all hardware drivers Verified Active Directory DNS settings (Vista works relatively well on the same network) Reset all TCP/IP settings on all adapters using the netsh commands to do so Disabled ipv6 on all adapters Disable wifi adapter while on work network Locked the network card to 100/Full, 1000/Full; also tried Auto Added various important addresses to hosts file (exchange, dns, ad) -- removed when didn't help My background is a jpeg (sounds unrelated but there is apparently a win7 login bug related to solid color background) More I have forgotten The IT staff at my company indicated they believe this is due to having Windows 2003 AD servers and not having any Windows 2008 R2 AD servers. Other than that, they have no advice or assistance to offer other than a rebuild (already tried that once with similar symptoms), or downgrade to Vista. Any thoughts out there?

  Read the article

• VsFTPd - pam_mkhomedir

  - by Totor

  I am trying to set up a FTP server that authenticates against an LDAP server. This part is done and works. My server is VsFTPd on Ubuntu Server 11.04. But I have to create the home directories for my LDAP users. I am trying to user the pam_mkhomedir module but it is not working: when I add its line to the /etc/pam.d/vsftpd file, my users can not login anymore to the FTP server. The problem is that I have very few information on what is wrong. VsFTPd just responds 530: login incorrect and I could not find a way to get debug or error messages from pam_mkhomedir. Here are my different configuration files. The /etc/pam.d/vsftpd file: auth required pam_listfile.so item=user sense=deny file=/etc/ftpusers onerr=succeed auth required pam_ldap.so account required pam_ldap.so password required pam_ldap.so session optional pam_mkhomedir.so skel=/home/skel debug The /etc/vsftpd.conf file: listen=YES anonymous_enable=NO local_enable=YES write_enable=YES dirmessage_enable=YES use_localtime=YES xferlog_enable=YES connect_from_port_20=YES pam_service_name=vsftpd rsa_cert_file=/etc/ssl/private/vsftpd.pem guest_enable=YES session_support=YES log_ftp_protocol=YES tcp_wrappers=YES Permissions on /home and /home/skel: root@ftp:/home# ls -al total 16 drwxrwxrwx 4 root root 4096 2011-10-11 21:19 . drwxr-xr-x 21 root root 4096 2011-09-27 13:32 .. drwxrwxrwx 2 root root 4096 2011-10-11 19:34 skel drwxrwxrwx 5 foo foo 4096 2011-10-11 21:11 foo root@ftp:/home# ls -al skel/ total 16 drwxrwxrwx 2 root root 4096 2011-10-11 19:34 . drwxrwxrwx 4 root root 4096 2011-10-11 21:19 .. -rwxrwxrwx 1 root root 3352 2011-10-11 19:34 .bashrc -rwxrwxrwx 1 root root 675 2011-10-11 19:34 .profile Yes, I know, permissions are not properly set but security is not the issue here: I first need to get it to work. So, to recapitulate: without pam_mkhomedir my LDAP users can login, but they cannot do anything because they are in an empty chrooted jail. If I add pam_mkhomedir, they cannot login anymore. If anyone has an idea why, or know how to get more information from logs, I would be very grateful, thanks.

  Read the article

• ssh tunnel error "ssh_exchange_identification: Connection closed by remote host"

  - by Jacob Ewing

  I'm trying to use an ssh tunnel from my office machine to my home machine, and get an error when I try to use it. What I'm doing is starting one shell like so: ssh -gL 12345:my.home.domain:22 my.home.domain This is giving me a proper shell, no problem. What I normally do then is ssh to my home machine through this office machine, like so: ssh -p 12345 127.0.0.1 This has always worked for me, until last week, when I set up a new system on my home machine (switching from Ubuntu to Debian). Now I get an error. I can still open up my initial ssh connection, but when I try to use that tunnel, I get (on the office machine) this error: ssh_exchange_identification: Connection closed by remote host Also, when that happens, the open shell that I have the tunnelling set up through gets this line spat out at it: channel 3: open failed: connect failed: Connection timed out At which point, I'm at a loss. If any more info is needed, I'll be happy to post it. ============= further to that ============== After fiddling around further, I've found that I'm getting a different response from the server (my home machine that is) when I try to telnet in on the various ports. If I try: telnet my.home.domain 22 I get this back: Trying <my ip address>... Connected to <my domain>. Escape character is '^]'. SSH-2.0-OpenSSH_5.5p1 Debian-6+squeeze2 Which is what I would expect. After setting up the tunnel though, and then telnetting to that, I see this response: Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ============== and further still ================== As per kbulgrien's suggestion, here is the output from the client machine with the -v option: ssh -vp 24600 127.0.0.1 OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to 127.0.0.1 [127.0.0.1] port 24600. debug1: Connection established. debug1: identity file /home/jacob/.ssh/id_rsa type -1 debug1: identity file /home/jacob/.ssh/id_rsa-cert type -1 debug1: identity file /home/jacob/.ssh/id_dsa type -1 debug1: identity file /home/jacob/.ssh/id_dsa-cert type -1 debug1: identity file /home/jacob/.ssh/id_ecdsa type -1 debug1: identity file /home/jacob/.ssh/id_ecdsa-cert type -1 ssh_exchange_identification: Connection closed by remote host

  Read the article

• Debian Apache2 and SSL

  - by Topher Fangio

  Hello all, I recently took over a server that is using Apache2 with SSL. I have setup a new server to which I am migrating all of the old websites so that we can more easily scale (it's a cloud server) and so that I can set everything up correctly (or at least with some sort of convention). I have read quite a few articles on setting up Apache2 and SSL with virtual hosts, but I'm a bit confused because all of the examples show three files and I only seem to have two. To compound the problem, they are all named differently (do the file extensions actually make a difference?). The examples show something to this effect: <VirtualHost X.X.X.X:443> ServerAlias something.mydomain.com ServerAdmin [email protected] DocumentRoot /var/www/project/client/site SSLEngine on SSLCertificateFile /etc/ssl/certs/mydomain-cert.pem SSLCertificateKeyFile /etc/ssl/private/mydomain-key.pem SSLCertificateChainFile /etc/ssl/certs/mydomain-ca.crt </VirtualHost> However, the files I have are: _.mydomain.com.crt gd_bundle.crt It is a wildcard certificate that we purchased through GoDaddy I believe. I believe that the first file is the actual certificate file and the gd_bundle.crt is the chain file, but that leaves me without a key file. There is also a random mydomain.csr file lying around on the old server, but it wasn't one of the files bundled with the download from GoDaddy, so I'm not really sure as to what it is. Any help in figuring out what I need to do would be greatly appreciated. I am software developer, so I know my way around computers, but I have only dabbled in server setup/maintenance. Much Thanks!

  Read the article

• windows 2003 server : can't find a primary authoritative dns server for the name srv.domain1.local [

  - by phill

  I originally tried to rejoin a computer to a network which led to a "cannot find domain" error. The username/password box don't even come up. some tests i ran: I can ping the server, however I can't ping the domain name domain1.local. nslookup can't find the domain either. It looks to the isp's dns instead of my own to resolve the local machines. So i go to the dns and run netdiag.exe and gives me this error. DNS test . . . . . . . . . . . . . : Failed [WARNING] Cannot find a primary authoritative DNS server for the name 'stmartinsrv.stmartin.local.'. [RCODE_SERVER_FAILURE] The name 'srv.domain1.local.' may not be registered in DNS. [WARNING] The DNS entries for this DC are not registered correctly on DNS se rver '68.94.156.1'. Please wait for 30 minutes for DNS server replication. [WARNING] The DNS entries for this DC are not registered correctly on DNS se rver '68.94.157.1'. Please wait for 30 minutes for DNS server replication. [FATAL] No DNS servers have the DNS records for this DC registered. Redir and Browser test . . . . . . : Passed List of NetBt transports currently bound to the Redir NetBT_Tcpip_{04BB0F6B-06AE-4D60-80C8-2A7A24C1D87B} The redir is bound to 1 NetBt transport. List of NetBt transports currently bound to the browser NetBT_Tcpip_{04BB0F6B-06AE-4D60-80C8-2A7A24C1D87B} The browser is bound to 1 NetBt transport. from previous postings, I've tried adding the domain suffix to the nic ip properties to both the client machine and the dc server which didn't help. any ideas? thanks in advance

  Read the article

• nginx proxypass content 404s when adding caching location block

  - by Thermionix

  Below is my nginx conf - the location block for adding expires max to content is causing issues with content from the /internal proxied sites. nginx error log; 2011/11/22 15:51:23 [error] 22124#0: *2 open() "/var/www/internal/static/javascripts/lib.js" failed (2: No such file or directory), client: 127.0.0.1, server: example.com, request: "GET /internal/static/javascripts/lib.js?0.6.11RC1 HTTP/1.1", host: "example.com", referrer: "https://example.com/internal/" browser error; lib.js Failed to load resource: the server responded with a status of 404 (Not Found) commenting out the expires max location block allows the proxied sites to work as intended. Config files; proxy.conf location /internal { proxy_pass http://localhost:10001/internal/; include proxy.inc; } .... more entries .... sites-enabled/main server { listen 80; include www.conf; } server { listen 443; include proxy.conf; include www.conf; ssl on; } www.conf root /var/www; server_name example.com; location / { autoindex off; allow all; rewrite ^/$ /mainsite last; } location ~* \.(jpg|jpeg|gif|css|png|js|ico)$ { expires max; } # hide protected files location ~* \.(engine|inc|info|install|module|profile|po|sh|.*sql|theme|tpl(\.php)?|xtmpl)$|^(code-style\.pl|Entries.*|Repository|Root|Tag|Template)$ { deny all; } location ~ \.php$ { fastcgi_index index.php; include fastcgi_params; if (-f $request_filename) { fastcgi_pass 127.0.0.1:9000; } } proxy.inc proxy_connect_timeout 59s; proxy_send_timeout 600; proxy_read_timeout 600; proxy_buffer_size 64k; proxy_buffers 16 32k; proxy_pass_header Set-Cookie; proxy_redirect off; proxy_hide_header Vary; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; proxy_set_header Accept-Encoding ''; proxy_ignore_headers Cache-Control Expires; proxy_set_header Referer $http_referer; proxy_set_header Host $host; proxy_set_header Cookie $http_cookie; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;

  Read the article

• No network upsets gnome

  - by Darren Cook

  An issue that has been bothering me for over a year now. My notebook, running ubuntu 10.04, is almost all the time using a wired connection, with static IP address. And a remote DNS server. Network is configured with entries in /etc/network/interfaces and /etc/resolv.conf, rather than whatever the gnome UI tool was (*) But if I'm out, or simply unplug the network cable, a few things get weird. Specifically the gnome-panel stops working - it is still there, but isn't updating. And opening a nautilus window (e.g. to look at files on the local disk) has huge time-outs. By that I mean it will not open the window for something like 30 or 60 seconds; but when it does finally open it I can see the files and it is perfectly usable. Everything else works fine, alt-tab between windows, etc. I use the commandline to find the pid of gnome-panel, kill it, wait a couple of seconds, and it opens up a fresh panel which is normally usable. (Something like 10 minutes later it will have locked/crashed again; the same for the nautilus windows.) I'm guessing this is a DNS issue? Would setting up a local DNS server help? Guess number 2 was related to having a file server mount (samba, though running on another linux box), and symbolic links to files and directories on that file server on my desktop. My question is a bit vague... Does anyone recognize these symptoms, and have a suggestion? Or do you have some troubleshooting suggestions for narrowing down the problem? My /etc/hosts: 127.0.0.1 localhost 127.0.1.1 myhost # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts 127.0.0.1 testsite.local #Other test website URLs here UPDATE: Some timings to open some desktop folder icons. This is after pulling out the network cable. A sub-directory of the desktop took 23 secs to open up. Content appears immediately (just 8 files, it has no further subdirectories). The home directory icon took 12 seconds to open up, but then took about 30 seconds for the files to appear. I closed it and tried again. This time it took 18 seconds to open up, but then 70 seconds before anything appeared. *: I couldn't work out how to use the gnome network tool for my needs, which include 3-4 static IPs for testing virtual hosts locally.

  Read the article

• How to allow local LAN access while connected to Cisco VPN?

  - by Ian Boyd

  How can I maintain local LAN access while connected to Cisco VPN? When connecting using Cisco VPN, the server has to ability to instruct the client to prevent local LAN access. Assuming this server-side option cannot be turned off, how can allow local LAN access while connected with a Cisco VPN client? I used to think it was simply a matter of routes being added that capture LAN traffic with a higher metric, for example: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.255.0.0 10.0.0.3 10.0.0.3 20 <--Local LAN 10.0.0.0 255.255.0.0 192.168.199.1 192.168.199.12 1 <--VPN Link And trying to delete the 10.0.x.x -> 192.168.199.12 route don't have any effect: >route delete 10.0.0.0 >route delete 10.0.0.0 mask 255.255.0.0 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 if 192.168.199.12 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 if 0x3 And while it still might simply be a routing issue, attempts to add or delete routes fail. At what level is Cisco VPN client driver doing what in the networking stack that takes overrides a local administrator's ability to administer their machine? The Cisco VPN client cannot be employing magic. It's still software running on my computer. What mechanism is it using to interfere with my machine's network? What happens when an IP/ICMP packet arrives on the network? Where in the networking stack is the packet getting eaten? See also No internet connection with Cisco VPN Cisco VPN Client interrupts connectivity to my LDAP server Cisco VPN stops Windows 7 Browsing How can I prohibit the creation of a route in Windows XP upon connection to Cisco VPN? Rerouting local LAN and Internet traffic when in VPN VPN Client "Allow local LAN Access" Allow Local LAN Access for VPN Clients on the VPN 3000 Concentrator Configuration Example LAN access gone when I connect to VPN Windows XP Documentation: Route Edit: Things I've not yet tried: >route delete 10.0.* Update: Since Cisco has abandoned their old client, in favor of AnyConnect (HTTP SSL based VPN), this question, unsolved, can be left as a relic of history. Going forward, we can try to solve the same problem with their new client.

  Read the article

• JBoss AS 5: starts but can't connect (Windows, remote)

  - by Nuwan

  Hello I installed Jboss 5.0GA and Its works fine in localhost.But I want It to access through remote Machine.Then I bind my IP address to my server and started it.This is the command I used run.bat -b 10.17.62.63 Then the server Starts fine This is the console log when starting the server > =============================================================================== > > JBoss Bootstrap Environment > > JBOSS_HOME: C:\jboss-5.0.0.GA > > JAVA: C:\Program Files\Java\jdk1.6.0_34\bin\java > > JAVA_OPTS: -Dprogram.name=run.bat -server -Xms128m -Xmx512m > -XX:MaxPermSize=25 6m -Dorg.jboss.resolver.warning=true -Dsun.rmi.dgc.client.gcInterval=3600000 -Ds un.rmi.dgc.server.gcInterval=3600000 > > CLASSPATH: C:\jboss-5.0.0.GA\bin\run.jar > > =============================================================================== > > run.bat: unused non-option argument: ûb run.bat: unused non-option > argument: 0.0.0.0 13:43:38,179 INFO [ServerImpl] Starting JBoss > (Microcontainer)... 13:43:38,179 INFO [ServerImpl] Release ID: JBoss > [Morpheus] 5.0.0.GA (build: SV NTag=JBoss_5_0_0_GA date=200812041714) > 13:43:38,179 INFO [ServerImpl] Bootstrap URL: null 13:43:38,179 INFO > [ServerImpl] Home Dir: C:\jboss-5.0.0.GA 13:43:38,179 INFO > [ServerImpl] Home URL: file:/C:/jboss-5.0.0.GA/ 13:43:38,195 INFO > [ServerImpl] Library URL: file:/C:/jboss-5.0.0.GA/lib/ 13:43:38,195 > INFO [ServerImpl] Patch URL: null 13:43:38,195 INFO [ServerImpl] > Common Base URL: file:/C:/jboss-5.0.0.GA/common/ > > 13:43:38,195 INFO [ServerImpl] Common Library URL: > file:/C:/jboss-5.0.0.GA/comm on/lib/ 13:43:38,195 INFO [ServerImpl] > Server Name: default 13:43:38,195 INFO [ServerImpl] Server Base Dir: > C:\jboss-5.0.0.GA\server 13:43:38,195 INFO [ServerImpl] Server Base > URL: file:/C:/jboss-5.0.0.GA/server/ > > 13:43:38,210 INFO [ServerImpl] Server Config URL: > file:/C:/jboss-5.0.0.GA/serve r/default/conf/ 13:43:38,210 INFO > [ServerImpl] Server Home Dir: C:\jboss-5.0.0.GA\server\defaul t > 13:43:38,210 INFO [ServerImpl] Server Home URL: > file:/C:/jboss-5.0.0.GA/server/ default/ 13:43:38,210 INFO > [ServerImpl] Server Data Dir: C:\jboss-5.0.0.GA\server\defaul t\data > 13:43:38,210 INFO [ServerImpl] Server Library URL: > file:/C:/jboss-5.0.0.GA/serv er/default/lib/ 13:43:38,210 INFO > [ServerImpl] Server Log Dir: C:\jboss-5.0.0.GA\server\default \log > 13:43:38,210 INFO [ServerImpl] Server Native Dir: > C:\jboss-5.0.0.GA\server\defa ult\tmp\native 13:43:38,210 INFO > [ServerImpl] Server Temp Dir: C:\jboss-5.0.0.GA\server\defaul t\tmp > 13:43:38,210 INFO [ServerImpl] Server Temp Deploy Dir: > C:\jboss-5.0.0.GA\server \default\tmp\deploy 13:43:39,710 INFO > [ServerImpl] Starting Microcontainer, bootstrapURL=file:/C:/j > boss-5.0.0.GA/server/default/conf/bootstrap.xml 13:43:40,851 INFO > [VFSCacheFactory] Initializing VFSCache [org.jboss.virtual.pl > ugins.cache.IterableTimedVFSCache] 13:43:40,866 INFO > [VFSCacheFactory] Using VFSCache [IterableTimedVFSCache{lifet > ime=1800, resolution=60}] 13:43:41,616 INFO [CopyMechanism] VFS temp > dir: C:\jboss-5.0.0.GA\server\defaul t\tmp 13:43:41,648 INFO > [ZipEntryContext] VFS force nested jars copy-mode is enabled. > > 13:43:44,288 INFO [ServerInfo] Java version: 1.6.0_34,Sun > Microsystems Inc. 13:43:44,288 INFO [ServerInfo] Java VM: Java > HotSpot(TM) Server VM 20.9-b04,Sun Microsystems Inc. 13:43:44,288 > INFO [ServerInfo] OS-System: Windows XP 5.1,x86 13:43:44,569 INFO > [JMXKernel] Legacy JMX core initialized 13:43:50,148 INFO > [ProfileServiceImpl] Loading profile: default from: org.jboss > .system.server.profileservice.repository.SerializableDeploymentRepository@e72f0c > (root=C:\jboss-5.0.0.GA\server, > key=org.jboss.profileservice.spi.ProfileKey@143b > 82c3[domain=default,server=default,name=default]) 13:43:50,148 INFO > [ProfileImpl] Using repository:org.jboss.system.server.profil > eservice.repository.SerializableDeploymentRepository@e72f0c(root=C:\jboss-5.0.0. > GA\server, > key=org.jboss.profileservice.spi.ProfileKey@143b82c3[domain=default,s > erver=default,name=default]) 13:43:50,148 INFO [ProfileServiceImpl] > Loaded profile: ProfileImpl@8b3bb3{key=o > rg.jboss.profileservice.spi.ProfileKey@143b82c3[domain=default,server=default,na > me=default]} 13:43:54,804 INFO [WebService] Using RMI server > codebase: http://127.0.0.1:8083 / 13:44:12,147 INFO [CXFServerConfig] > JBoss Web Services - Stack CXF Runtime Serv er 13:44:12,147 INFO > [CXFServerConfig] 3.1.2.GA 13:44:29,788 INFO > [Ejb3DependenciesDeployer] Encountered deployment AbstractVFS > DeploymentContext@29776073{vfszip:/C:/jboss-5.0.0.GA/server/default/deploy/myE-e > jb.jar} 13:44:29,819 INFO [Ejb3DependenciesDeployer] Encountered > deployment AbstractVFS > DeploymentContext@29776073{vfszip:/C:/jboss-5.0.0.GA/server/default/deploy/myE-e > jb.jar} 13:44:29,819 INFO [Ejb3DependenciesDeployer] Encountered > deployment AbstractVFS > DeploymentContext@29776073{vfszip:/C:/jboss-5.0.0.GA/server/default/deploy/myE-e > jb.jar} 13:44:29,819 INFO [Ejb3DependenciesDeployer] Encountered > deployment AbstractVFS > DeploymentContext@29776073{vfszip:/C:/jboss-5.0.0.GA/server/default/deploy/myE-e > jb.jar} 13:44:37,116 INFO [JMXConnectorServerService] JMX Connector > server: service:jmx > :rmi://127.0.0.1/jndi/rmi://127.0.0.1:1090/jmxconnector 13:44:38,022 > INFO [MailService] Mail Service bound to java:/Mail 13:44:43,162 WARN > [JBossASSecurityMetadataStore] WARNING! POTENTIAL SECURITY RI SK. It > has been detected that the MessageSucker component which sucks > messages f rom one node to another has not had its password changed > from the installation d efault. Please see the JBoss Messaging user > guide for instructions on how to do this. 13:44:43,209 WARN > [AnnotationCreator] No ClassLoader provided, using TCCL: org. > jboss.managed.api.annotation.ManagementComponent 13:44:43,600 INFO > [TransactionManagerService] JBossTS Transaction Service (JTA version) > - JBoss Inc. 13:44:43,600 INFO [TransactionManagerService] Setting up property manager MBean and JMX layer 13:44:44,366 INFO > [TransactionManagerService] Initializing recovery manager 13:44:44,678 > INFO [TransactionManagerService] Recovery manager configured > 13:44:44,678 INFO [TransactionManagerService] Binding > TransactionManager JNDI R eference 13:44:44,787 INFO > [TransactionManagerService] Starting transaction recovery man ager > 13:44:46,428 INFO [Http11Protocol] Initializing Coyote HTTP/1.1 on > http-127.0.0 .1-8080 13:44:46,459 INFO [AjpProtocol] Initializing > Coyote AJP/1.3 on ajp-127.0.0.1-80 09 13:44:46,459 INFO > [StandardService] Starting service jboss.web 13:44:46,475 INFO > [StandardEngine] Starting Servlet Engine: JBoss Web/2.1.1.GA > 13:44:46,616 INFO [Catalina] Server startup in 350 ms 13:44:46,709 > INFO [TomcatDeployment] deploy, ctxPath=/web-console, vfsUrl=manag > ement/console-mgr.sar/web-console.war 13:44:48,553 INFO > [TomcatDeployment] deploy, ctxPath=/juddi, vfsUrl=juddi-servi > ce.sar/juddi.war 13:44:48,678 INFO [RegistryServlet] Loading jUDDI > configuration. 13:44:48,694 INFO [RegistryServlet] Resources loaded > from: /WEB-INF/juddi.prope rties 13:44:48,709 INFO [RegistryServlet] > Initializing jUDDI components. 13:44:48,991 INFO [TomcatDeployment] > deploy, ctxPath=/invoker, vfsUrl=http-invo ker.sar/invoker.war > 13:44:49,162 INFO [TomcatDeployment] deploy, ctxPath=/jbossws, > vfsUrl=jbossws.s ar/jbossws-management.war 13:44:49,475 INFO > [RARDeployment] Required license terms exist, view vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/jboss-local-jdbc.rar/META-INF/ra.xml > 13:44:49,569 INFO [RARDeployment] Required license terms exist, view > vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/jboss-xa-jdbc.rar/META-INF/ra.xml > 13:44:49,741 INFO [RARDeployment] Required license terms exist, view > vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/jms-ra.rar/META-INF/ra.xml > 13:44:49,819 INFO [RARDeployment] Required license terms exist, view > vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/mail-ra.rar/META-INF/ra.xml > 13:44:49,912 INFO [RARDeployment] Required license terms exist, view > vfszip:/C: > /jboss-5.0.0.GA/server/default/deploy/quartz-ra.rar/META-INF/ra.xml > 13:44:50,069 INFO [SimpleThreadPool] Job execution threads will use > class loade r of thread: main 13:44:50,115 INFO [QuartzScheduler] > Quartz Scheduler v.1.5.2 created. 13:44:50,131 INFO [RAMJobStore] > RAMJobStore initialized. 13:44:50,131 INFO [StdSchedulerFactory] > Quartz scheduler 'DefaultQuartzSchedule r' initialized from default > resource file in Quartz package: 'quartz.properties' > > 13:44:50,131 INFO [StdSchedulerFactory] Quartz scheduler version: > 1.5.2 13:44:50,131 INFO [QuartzScheduler] Scheduler DefaultQuartzScheduler_$_NON_CLUS TERED started. 13:44:51,194 INFO > [ConnectionFactoryBindingService] Bound ConnectionManager 'jb > oss.jca:service=DataSourceBinding,name=DefaultDS' to JNDI name > 'java:DefaultDS' 13:44:51,819 WARN [QuartzTimerServiceFactory] sql > failed: CREATE TABLE QRTZ_JOB > _DETAILS(JOB_NAME VARCHAR(80) NOT NULL, JOB_GROUP VARCHAR(80) NOT NULL, DESCRIPT ION VARCHAR(120) NULL, JOB_CLASS_NAME VARCHAR(128) NOT > NULL, IS_DURABLE VARCHAR( 1) NOT NULL, IS_VOLATILE VARCHAR(1) NOT > NULL, IS_STATEFUL VARCHAR(1) NOT NULL, R EQUESTS_RECOVERY VARCHAR(1) > NOT NULL, JOB_DATA BINARY NULL, PRIMARY KEY (JOB_NAM E,JOB_GROUP)) > 13:44:51,912 INFO [SimpleThreadPool] Job execution threads will use > class loade r of thread: main 13:44:51,928 INFO [QuartzScheduler] > Quartz Scheduler v.1.5.2 created. 13:44:51,928 INFO [JobStoreCMT] > Using db table-based data access locking (synch ronization). > 13:44:51,944 INFO [JobStoreCMT] Removed 0 Volatile Trigger(s). > 13:44:51,944 INFO [JobStoreCMT] Removed 0 Volatile Job(s). > 13:44:51,944 INFO [JobStoreCMT] JobStoreCMT initialized. 13:44:51,944 > INFO [StdSchedulerFactory] Quartz scheduler 'JBossEJB3QuartzSchedu > ler' initialized from an externally provided properties instance. > 13:44:51,959 INFO [StdSchedulerFactory] Quartz scheduler version: > 1.5.2 13:44:51,959 INFO [JobStoreCMT] Freed 0 triggers from 'acquired' / 'blocked' st ate. 13:44:51,975 INFO [JobStoreCMT] > Recovering 0 jobs that were in-progress at the time of the last > shut-down. 13:44:51,975 INFO [JobStoreCMT] Recovery complete. > 13:44:51,975 INFO [JobStoreCMT] Removed 0 'complete' triggers. > 13:44:51,975 INFO [JobStoreCMT] Removed 0 stale fired job entries. > 13:44:51,990 INFO [QuartzScheduler] Scheduler > JBossEJB3QuartzScheduler_$_NON_CL USTERED started. 13:44:52,381 INFO > [ServerPeer] JBoss Messaging 1.4.1.GA server [0] started 13:44:52,569 > INFO [QueueService] Queue[/queue/DLQ] started, fullSize=200000, pa > geSize=2000, downCacheSize=2000 13:44:52,584 INFO [QueueService] > Queue[/queue/ExpiryQueue] started, fullSize=20 0000, pageSize=2000, > downCacheSize=2000 13:44:52,709 INFO [ConnectionFactory] Connector > bisocket://127.0.0.1:4457 has l easing enabled, lease period 10000 > milliseconds 13:44:52,709 INFO [ConnectionFactory] > org.jboss.jms.server.connectionfactory.Co nnectionFactory@1a8ac5e > started 13:44:52,725 WARN [ConnectionFactoryJNDIMapper] > supportsFailover attribute is t rue on connection factory: > jboss.messaging.connectionfactory:service=ClusteredCo nnectionFactory > but post office is non clustered. So connection factory will *no t* > support failover 13:44:52,725 WARN [ConnectionFactoryJNDIMapper] > supportsLoadBalancing attribute is true on connection factory: > jboss.messaging.connectionfactory:service=Cluste redConnectionFactory > but post office is non clustered. So connection factory wil l *not* > support load balancing 13:44:52,740 INFO [ConnectionFactory] > Connector bisocket://127.0.0.1:4457 has l easing enabled, lease period > 10000 milliseconds 13:44:52,740 INFO [ConnectionFactory] > org.jboss.jms.server.connectionfactory.Co nnectionFactory@1d43178 > started 13:44:52,740 INFO [ConnectionFactory] Connector > bisocket://127.0.0.1:4457 has l easing enabled, lease period 10000 > milliseconds 13:44:52,756 INFO [ConnectionFactory] > org.jboss.jms.server.connectionfactory.Co nnectionFactory@52728a > started 13:44:53,084 INFO [ConnectionFactoryBindingService] Bound > ConnectionManager 'jb > oss.jca:service=ConnectionFactoryBinding,name=JmsXA' to JNDI name > 'java:JmsXA' 13:44:53,225 INFO [TomcatDeployment] deploy, ctxPath=/, > vfsUrl=ROOT.war 13:44:53,553 INFO [TomcatDeployment] deploy, > ctxPath=/jmx-console, vfsUrl=jmx-c onsole.war 13:44:53,975 INFO > [TomcatDeployment] deploy, ctxPath=/TestService, vfsUrl=TestS > erviceEAR.ear/TestService.war 13:44:55,662 INFO [JBossASKernel] > Created KernelDeployment for: myE-ejb.jar 13:44:55,709 INFO > [JBossASKernel] installing bean: jboss.j2ee:jar=myE-ejb.jar,n > ame=RPSService,service=EJB3 13:44:55,725 INFO [JBossASKernel] with > dependencies: 13:44:55,725 INFO [JBossASKernel] and demands: > 13:44:55,725 INFO [JBossASKernel] > jboss.ejb:service=EJBTimerService 13:44:55,725 INFO [JBossASKernel] > and supplies: 13:44:55,725 INFO [JBossASKernel] > jndi:RPSService/remote 13:44:55,725 INFO [JBossASKernel] Added > bean(jboss.j2ee:jar=myE-ejb.jar,name=RP SService,service=EJB3) to > KernelDeployment of: myE-ejb.jar 13:44:56,772 INFO > [SessionSpecContainer] Starting jboss.j2ee:jar=myE-ejb.jar,na > me=RPSService,service=EJB3 13:44:56,803 INFO [EJBContainer] STARTED > EJB: com.monz.rpz.RPSService ejbName: RPSService 13:44:56,819 INFO > [JndiSessionRegistrarBase] Binding the following Entries in G lobal > JNDI: > > > 13:44:57,381 INFO [DefaultEndpointRegistry] register: > jboss.ws:context=myE-ejb, endpoint=RPSService 13:44:57,428 INFO > [DescriptorDeploymentAspect] Add Service id=RPSService > address=http://127.0.0.1:8080/myE-ejb/RPSService > implementor=com.monz.rpz.RPSService > invoker=org.jboss.wsf.stack.cxf.InvokerEJB3 mtomEnabled=false > 13:44:57,459 INFO [DescriptorDeploymentAspect] JBossWS-CXF > configuration genera ted: > file:/C:/jboss-5.0.0.GA/server/default/tmp/jbossws/jbossws-cxf1864137209199 > 110130.xml 13:44:57,569 INFO [TomcatDeployment] deploy, ctxPath=/myE-ejb, vfsUrl=myE-ejb.j ar 13:44:57,709 WARN [config] > Unable to process deployment descriptor for context '/myE-ejb' > 13:44:59,334 INFO [Http11Protocol] Starting Coyote HTTP/1.1 on > http-127.0.0.1-8 080 13:44:59,397 INFO [AjpProtocol] Starting Coyote > AJP/1.3 on ajp-127.0.0.1-8009 13:44:59,459 INFO [ServerImpl] JBoss > (Microcontainer) [5.0.0.GA (build: SVNTag= JBoss_5_0_0_GA > date=200812041714)] Started in 1m:21s:233ms But Still I cant connect to It when I Type my IP address in my browser thanks

  Read the article

• Mac OS X behind OpenLDAP and Samba

  - by Sam Hammamy

  I have been battling for a week now to get my Mac (Mountain Lion) to authenticate on my home network's OpenLDAP and Samba. From several sources, like the Ubuntu community docs, and other blogs, and after a hell of a lot of trial and error and piecing things together, I have created a samba.ldif that will pass the smbldap-populate when combined with apple.ldif and I have a fully functional OpenLDAP server and a Samba PDC that uses LDAP to authenticate the OS X Machine. The problem is that when I login, the home directory is not created or pulled from the server. I get the following in system.log Sep 21 06:09:15 Sams-MacBook-Pro.local SecurityAgent[265]: User info context values set for sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got ruser: (null) Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got service: authorization Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): no authauth availale for user. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): failed: 7 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Failed to determine Kerberos principal name. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Done cleanup3 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Kerberos 5 refuses you Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): pam_sm_authenticate: ntlm Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_acct_mgmt(): OpenDirectory - Membership cache TTL set to 1800. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_record_check_pwpolicy(): retval: 0 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Establishing credentials Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Context initialised Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): pam_sm_setcred: ntlm user sam doesn't have auth authority All that's great and good and I authenticate. Then I get CFPreferences: user home directory for user kCFPreferencesCurrentUser at /Network/Servers/172.17.148.186/home/sam is unavailable. User domains will be volatile. Failed looking up user domain root; url='file://localhost/Network/Servers/172.17.148.186/home/sam/' path=/Network/Servers/172.17.148.186/home/sam/ err=-43 uid=9000 euid=9000 If you're wondering where /Network/Servers/IP/home/sam comes from, it's from a couple of blogs that said the OpenLDAP attribute apple-user-homeDirectory should have that value and the NFSHomeDirectory on the mac should point to apple-user-homeDirectory I also set the attr apple-user-homeurl to <home_dir><url>smb://172.17.148.186/sam/</url><path></path></home_dir> which I found on this forum. Any help is appreciated, because I'm banging my head against the wall at this point. By the way, I intend to create a blog on my vps just for this, and create an install script in python that people can download so no one has to go through what I've had to go through this week :) After some sleep I am going to try to login from a windows machine and report back here. Thanks Sam

  Read the article

• ssl_error_rx_record_too_long connection error with SSL site in Firefox

  - by Thomas

  I am trying to set up SSL in Apache but when I go to the server in Firefox I get the following error message: An error occurred during a connection to sludge.home. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) My virtual host config file looks like this. <IfDefine SSL> <VirtualHost *:443> ServerName sludge.home SSLEngine on SSLCertificateFile /usr/local/apache/cert/server.crt SSLCertificateKeyFile /usr/local/apache/cert/server.pem SSLProtocol -SSLv2 SSL CipherSuite HIGH:!ADH:!EXP:!MD5:!NULL DocumentRoot "/usr/local/apache/htdocs" ServerAdmin [email protected] <Location /> AuthType Digest AuthName "private area" AuthDigestDomain / AuthDigestProvider file AuthUserFile /usr/local/apache/passwd/digest_pw Require valid-user </Location> <Directory /usr/local/apache/htdocs/bugz> AddHandler cgi-script .cgi Options +Indexes +ExecCGI DirectoryIndex index.cgi AllowOverride Limit FileInfo Indexes </Directory> <Directory /usr/local/apache/htdocs/bugzilla> AddHandler cgi-script .cgi Options +Indexes +ExecCGI DirectoryIndex index.cgi AllowOverride Limit FileInfo Indexes </Directory> <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> <Directory "/usr/local/apache/htdocs"> Options Indexes FollowSymLinks Allow Override None Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.html </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> </VirtualHost> </IfDefine> A telnet to this server reveals that server is sending plain HTML back. Further more it seems as though mod_ssl is not loaded/working even though when I httpd -l it shows up as being statically compiled in. I have exhausted most avenues I can think of.

  Read the article

• How do you host multiple public facing websites on a VPS?

  - by pedroarvy

  We host about 30 websites using typical shared hosting plans using ASP.NET and SQL 2000/2005/2008. I am now wondering about hosting all of these websites using our own virtual private server. This is clearly cheaper but comes with a lot of questions I need answers to: Is the risk of having to keep this VPS server up and running worth it? Until now, the host provider has managed the server and we have not had to worry about crashes, downtime, software patches etc. We are not server administrators, we are programmers, so this is not really our expertise. On the other hand, it may not be hard to learn. When we make a website live, we log in to a domain management control panel and change the primary and secondary name servers to point to our shared web host: Eg ns1.sharedwebhost.com and ns2.sharedwebhost.com These name servers are going to have to change when we have a VPS. I don’t understand anything about how to set this up. Is there some useful info anyone could direct me to? Or is there software we need to install to make the primary and secondary name servers work on our VPS? The control panel we have for shared hosting comes with DNS management like this: http://www.yart.com.au/stackoverflow/dns.png What software would I need to install to create this for each site we host at a VPS? The control panel we have for shared hosting also comes with a POP email interface that allows email addresses to be added easily by our customers. Is this something that can be easily set up at a VPS so clients can manage their own email addresses? Is there software we need to install to make this work?

  Read the article

• Is it possible to extract contents of a ThinApp container?

  - by rsk82

  Is there possible to extract such packages made by somebody else. Ok, so if there is no general way of extracting such archives, which can be a huge exe file or tiny exe starter with huge packed *.bin file with main files of an app that is to be run in portable way - is there a way to set an option in compilation *.ini file or other way to make such package able to be extracted. I remember I read somewhere that somebody created a tiny program (in was mentioned in vmware forums as far as I can remember, it was a crude thing coded for private use and I never managed to download it) to sit with main portable application and if such application has an open/save file dialog, it is possible to navigate to that program which virtually sits in the program files alongside main app from within the main app, and such program would scan all files that it can see and somehow is able to distiguish a real file from virtual one, and save all virtual files in a structure that is similar to the initial compilation folder from which portable app was created. I know that it is a very round-about way of doing things, but maybe the only one feasible. Nevertheless any news on this front ? Do antiviruses can somehow unpack these things ? Maybe they must buy a code or license for it from VmWare ? Edit: I found http://communities.vmware.com/thread/257433?tstart=600 and still trying to make sense out of this. Wrong, this was about moving old version of thinapp to win7.

  Read the article

• Sync OneNote Notebooks to/on SkyDrive

  - by Sam

  I've got OneNote running on all computers in our house, using it all the time with several people and computers. The only drawback: I want to keep the copies of OneNote in sync without having to run a dedicated server myself. Right now one of my computers has a folder share, where all others sync to, but this is highly impractical since the computer is not always running. So my question is: is it possible to put the notebook files on a (private) SkyDrive Folder and have all the computers sync to there? This way all computers could keep in sync whenever they got access to the web. Can this be done? and, of course, How? [Update] Maybe I should not have taken knowledge about OneNote as granted: OneNote uses a propietary file format, but has a very good in-file-syncing, working on network shares. Generic 'just sync the complete file' won't be useful at all, because I'd just have 'file has changed on server and on client' conflicts all the time. The sync needs to know OneNote files and be able to sync the content - eg. OneNote itself needs to sync the files, not some generic sync tool.

  Read the article

• How to solve "403 Forbidden" on CentOS6 with SELinux Disabled?

  - by André

  I have a machine on Linode that is driving me crazy. Linode does not have SELinux on CentOS6... I'm trying to configure to put my website in "/home/websites/public_html/mysite.com/public" As I don´t have SELinux enable, how can I avoid the "403 Forbidden" that I get when trying to access the webpage? Sorry for my english. Best Regards, Update1, ERROR_LOG [Mon Oct 17 14:04:16 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:08:07 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:10:25 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:10:41 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:32:35 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:34:45 2011] [error] [client 58.218.199.227] (13)Permission denied: access to /proxy-1.php denied [Mon Oct 17 15:32:25 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 15:37:26 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 15:37:43 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 15:38:32 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 15:42:56 2011] [crit] [client 127.0.0.1] (13)Permission denied: /home/websites/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable [Mon Oct 17 15:43:12 2011] [crit] [client 127.0.0.1] (13)Permission denied: /home/websites/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable [Mon Oct 17 15:45:34 2011] [crit] [client 127.0.0.1] (13)Permission denied: /home/websites/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable [Mon Oct 17 15:51:25 2011] [crit] [client 127.0.0.1] (13)Permission denied: /home/websites/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable Upadate2, /home/websites directory drwx------ 3 websites websites 4096 Oct 17 14:52 . drwxr-xr-x. 3 root root 4096 Oct 17 13:42 .. -rw------- 1 websites websites 372 Oct 17 14:52 .bash_history -rw-r--r-- 1 websites websites 18 May 30 11:46 .bash_logout -rw-r--r-- 1 websites websites 176 May 30 11:46 .bash_profile -rw-r--r-- 1 websites websites 124 May 30 11:46 .bashrc drwxrwxr-x 3 websites apache 4096 Oct 17 13:45 public_html Update3, httpd.conf ### Section 1: Global Environment ServerTokens OS ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 60 KeepAlive Off MaxKeepAliveRequests 100 KeepAliveTimeout 15 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 4 MaxClients 300 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> #Listen 12.34.56.78:80 Listen 80 LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule include_module modules/mod_include.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule status_module modules/mod_status.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule info_module modules/mod_info.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule userdir_module modules/mod_userdir.so LoadModule alias_module modules/mod_alias.so LoadModule substitute_module modules/mod_substitute.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_balancer_module modules/mod_proxy_balancer.so LoadModule proxy_ftp_module modules/mod_proxy_ftp.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule proxy_ajp_module modules/mod_proxy_ajp.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so Include conf.d/*.conf #ExtendedStatus On User apache Group apache ServerAdmin root@localhost #ServerName www.example.com:80 UseCanonicalName Off DocumentRoot "/var/www/html" # # Each directory to which Apache has access can be configured with respect # to which services and features are allowed and/or disabled in that # directory (and its subdirectories). # # First, we configure the "default" to be a very restrictive set of # features. # <Directory /> Options FollowSymLinks AllowOverride None </Directory> # # Note that from this point forward you must specifically allow # particular features to be enabled - so if something's not working as # you might expect, make sure that you have specifically enabled it # below. # # # This should be changed to whatever you set DocumentRoot to. # <Directory "/home/websites/public_html"> # # Possible values for the Options directive are "None", "All", # or any combination of: # Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews # # Note that "MultiViews" must be named *explicitly* --- "Options All" # doesn't give it to you. # # The Options directive is both complicated and important. Please see # http://httpd.apache.org/docs/2.2/mod/core.html#options # for more information. # Options Indexes FollowSymLinks # # AllowOverride controls what directives may be placed in .htaccess files. # It can be "All", "None", or any combination of the keywords: # Options FileInfo AuthConfig Limit # AllowOverride None # # Controls who can get stuff from this server. # Order allow,deny Allow from all </Directory> # # UserDir: The name of the directory that is appended onto a user's home # directory if a ~user request is received. # # The path to the end user account 'public_html' directory must be # accessible to the webserver userid. This usually means that ~userid # must have permissions of 711, ~userid/public_html must have permissions # of 755, and documents contained therein must be world-readable. # Otherwise, the client will only receive a "403 Forbidden" message. # # See also: http://httpd.apache.org/docs/misc/FAQ.html#forbidden # <IfModule mod_userdir.c> # # UserDir is disabled by default since it can confirm the presence # of a username on the system (depending on home directory # permissions). # UserDir disabled # # To enable requests to /~user/ to serve the user's public_html # directory, remove the "UserDir disabled" line above, and uncomment # the following line instead: # #UserDir public_html </IfModule> # # Control access to UserDir directories. The following is an example # for a site where these directories are restricted to read-only. # #<Directory /home/*/public_html> # AllowOverride FileInfo AuthConfig Limit # Options MultiViews Indexes SymLinksIfOwnerMatch IncludesNoExec # <Limit GET POST OPTIONS> # Order allow,deny # Allow from all # </Limit> # <LimitExcept GET POST OPTIONS> # Order deny,allow # Deny from all # </LimitExcept> #</Directory> # # DirectoryIndex: sets the file that Apache will serve if a directory # is requested. # # The index.html.var file (a type-map) is used to deliver content- # negotiated documents. The MultiViews Option can be used for the # same purpose, but it is much slower. # DirectoryIndex index.html index.html.var # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy All </Files> # # TypesConfig describes where the mime.types file (or equivalent) is # to be found. # TypesConfig /etc/mime.types # # DefaultType is the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain # # The mod_mime_magic module allows the server to use various hints from the # contents of the file itself to determine its type. The MIMEMagicFile # directive tells the module where the hint definitions are located. # <IfModule mod_mime_magic.c> # MIMEMagicFile /usr/share/magic.mime MIMEMagicFile conf/magic </IfModule> # # HostnameLookups: Log the names of clients or just their IP addresses # e.g., www.apache.org (on) or 204.62.129.132 (off). # The default is off because it'd be overall better for the net if people # had to knowingly turn this feature on, since enabling it means that # each client request will result in AT LEAST one lookup request to the # nameserver. # HostnameLookups Off #EnableMMAP off #EnableSendfile off # # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog logs/error_log LogLevel warn # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # "combinedio" includes actual counts of actual bytes received (%I) and sent (%O); this # requires the mod_logio module to be loaded. #LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio # # The location and format of the access logfile (Common Logfile Format). # If you do not define any access logfiles within a <VirtualHost> # container, they will be logged here. Contrariwise, if you *do* # define per-<VirtualHost> access logfiles, transactions will be # logged therein and *not* in this file. # #CustomLog logs/access_log common # # If you would like to have separate agent and referer logfiles, uncomment # the following directives. # #CustomLog logs/referer_log referer #CustomLog logs/agent_log agent # # For a single logfile with access, agent, and referer information # (Combined Logfile Format), use the following directive: # CustomLog logs/access_log combined ServerSignature On Alias /icons/ "/var/www/icons/" <Directory "/var/www/icons"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> # # WebDAV module configuration section. # <IfModule mod_dav_fs.c> # Location of the WebDAV lock database. DAVLockDB /var/lib/dav/lockdb </IfModule> # # ScriptAlias: This controls which directories contain server scripts. # ScriptAliases are essentially the same as Aliases, except that # documents in the realname directory are treated as applications and # run by the server when requested rather than as documents sent to the client. # The same rules about trailing "/" apply to ScriptAlias directives as to # Alias. # ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" # # "/var/www/cgi-bin" should be changed to whatever your ScriptAliased # CGI directory exists, if you have that configured. # <Directory "/var/www/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> IndexOptions FancyIndexing VersionSort NameWidth=* HTMLTable Charset=UTF-8 AddIconByEncoding (CMP,/icons/compressed.gif) x-compress x-gzip AddIconByType (TXT,/icons/text.gif) text/* AddIconByType (IMG,/icons/image2.gif) image/* AddIconByType (SND,/icons/sound2.gif) audio/* AddIconByType (VID,/icons/movie.gif) video/* AddIcon /icons/binary.gif .bin .exe AddIcon /icons/binhex.gif .hqx AddIcon /icons/tar.gif .tar AddIcon /icons/world2.gif .wrl .wrl.gz .vrml .vrm .iv AddIcon /icons/compressed.gif .Z .z .tgz .gz .zip AddIcon /icons/a.gif .ps .ai .eps AddIcon /icons/layout.gif .html .shtml .htm .pdf AddIcon /icons/text.gif .txt AddIcon /icons/c.gif .c AddIcon /icons/p.gif .pl .py AddIcon /icons/f.gif .for AddIcon /icons/dvi.gif .dvi AddIcon /icons/uuencoded.gif .uu AddIcon /icons/script.gif .conf .sh .shar .csh .ksh .tcl AddIcon /icons/tex.gif .tex AddIcon /icons/bomb.gif core AddIcon /icons/back.gif .. AddIcon /icons/hand.right.gif README AddIcon /icons/folder.gif ^^DIRECTORY^^ AddIcon /icons/blank.gif ^^BLANKICON^^ # # DefaultIcon is which icon to show for files which do not have an icon # explicitly set. # DefaultIcon /icons/unknown.gif # # AddDescription allows you to place a short description after a file in # server-generated indexes. These are only displayed for FancyIndexed # directories. # Format: AddDescription "description" filename # #AddDescription "GZIP compressed document" .gz #AddDescription "tar archive" .tar #AddDescription "GZIP compressed tar archive" .tgz # # ReadmeName is the name of the README file the server will look for by # default, and append to directory listings. # # HeaderName is the name of a file which should be prepended to # directory indexes. ReadmeName README.html HeaderName HEADER.html # # IndexIgnore is a set of filenames which directory indexing should ignore # and not include in the listing. Shell-style wildcarding is permitted. # IndexIgnore .??* *~ *# HEADER* README* RCS CVS *,v *,t # # DefaultLanguage and AddLanguage allows you to specify the language of # a document. You can then use content negotiation to give a browser a # file in a language the user can understand. # # Specify a default language. This means that all data # going out without a specific language tag (see below) will # be marked with this one. You probably do NOT want to set # this unless you are sure it is correct for all cases. # # * It is generally better to not mark a page as # * being a certain language than marking it with the wrong # * language! # # DefaultLanguage nl # # Note 1: The suffix does not have to be the same as the language # keyword --- those with documents in Polish (whose net-standard # language code is pl) may wish to use "AddLanguage pl .po" to # avoid the ambiguity with the common suffix for perl scripts. # # Note 2: The example entries below illustrate that in some cases # the two character 'Language' abbreviation is not identical to # the two character 'Country' code for its country, # E.g. 'Danmark/dk' versus 'Danish/da'. # # Note 3: In the case of 'ltz' we violate the RFC by using a three char # specifier. There is 'work in progress' to fix this and get # the reference data for rfc1766 cleaned up. # # Catalan (ca) - Croatian (hr) - Czech (cs) - Danish (da) - Dutch (nl) # English (en) - Esperanto (eo) - Estonian (et) - French (fr) - German (de) # Greek-Modern (el) - Hebrew (he) - Italian (it) - Japanese (ja) # Korean (ko) - Luxembourgeois* (ltz) - Norwegian Nynorsk (nn) # Norwegian (no) - Polish (pl) - Portugese (pt) # Brazilian Portuguese (pt-BR) - Russian (ru) - Swedish (sv) # Simplified Chinese (zh-CN) - Spanish (es) - Traditional Chinese (zh-TW) # AddLanguage ca .ca AddLanguage cs .cz .cs AddLanguage da .dk AddLanguage de .de AddLanguage el .el AddLanguage en .en AddLanguage eo .eo AddLanguage es .es AddLanguage et .et AddLanguage fr .fr AddLanguage he .he AddLanguage hr .hr AddLanguage it .it AddLanguage ja .ja AddLanguage ko .ko AddLanguage ltz .ltz AddLanguage nl .nl AddLanguage nn .nn AddLanguage no .no AddLanguage pl .po AddLanguage pt .pt AddLanguage pt-BR .pt-br AddLanguage ru .ru AddLanguage sv .sv AddLanguage zh-CN .zh-cn AddLanguage zh-TW .zh-tw # # LanguagePriority allows you to give precedence to some languages # in case of a tie during content negotiation. # # Just list the languages in decreasing order of preference. We have # more or less alphabetized them here. You probably want to change this. # LanguagePriority en ca cs da de el eo es et fr he hr it ja ko ltz nl nn no pl pt pt-BR ru sv zh-CN zh-TW # # ForceLanguagePriority allows you to serve a result page rather than # MULTIPLE CHOICES (Prefer) [in case of a tie] or NOT ACCEPTABLE (Fallback) # [in case no accepted languages matched the available variants] # ForceLanguagePriority Prefer Fallback # # Specify a default charset for all content served; this enables # interpretation of all content as UTF-8 by default. To use the # default browser choice (ISO-8859-1), or to allow the META tags # in HTML content to override this choice, comment out this # directive: # AddDefaultCharset UTF-8 # # AddType allows you to add to or override the MIME configuration # file mime.types for specific file types. # #AddType application/x-tar .tgz # # AddEncoding allows you to have certain browsers uncompress # information on the fly. Note: Not all browsers support this. # Despite the name similarity, the following Add* directives have nothing # to do with the FancyIndexing customization directives above. # #AddEncoding x-compress .Z #AddEncoding x-gzip .gz .tgz # If the AddEncoding directives above are commented-out, then you # probably should define those extensions to indicate media types: # AddType application/x-compress .Z AddType application/x-gzip .gz .tgz # # MIME-types for downloading Certificates and CRLs # AddType application/x-x509-ca-cert .crt AddType application/x-pkcs7-crl .crl # # AddHandler allows you to map certain file extensions to "handlers": # actions unrelated to filetype. These can be either built into the server # or added with the Action directive (see below) # # To use CGI scripts outside of ScriptAliased directories: # (You will also need to add "ExecCGI" to the "Options" directive.) # #AddHandler cgi-script .cgi # # For files that include their own HTTP headers: # #AddHandler send-as-is asis # # For type maps (negotiated resources): # (This is enabled by default to allow the Apache "It Worked" page # to be distributed in multiple languages.) # AddHandler type-map var # # Filters allow you to process content before it is sent to the client. # # To parse .shtml files for server-side includes (SSI): # (You will also need to add "Includes" to the "Options" directive.) # AddType text/html .shtml AddOutputFilter INCLUDES .shtml # # Action lets you define media types that will execute a script whenever # a matching file is called. This eliminates the need for repeated URL # pathnames for oft-used CGI file processors. # Format: Action media/type /cgi-script/location # Format: Action handler-name /cgi-script/location # # # Customizable error responses come in three flavors: # 1) plain text 2) local redirects 3) external redirects # # Some examples: #ErrorDocument 500 "The server made a boo boo." #ErrorDocument 404 /missing.html #ErrorDocument 404 "/cgi-bin/missing_handler.pl" #ErrorDocument 402 http://www.example.com/subscription_info.html # # # Putting this all together, we can internationalize error responses. # # We use Alias to redirect any /error/HTTP_<error>.html.var response to # our collection of by-error message multi-language collections. We use # includes to substitute the appropriate text. # # You can modify the messages' appearance without changing any of the # default HTTP_<error>.html.var files by adding the line: # # Alias /error/include/ "/your/include/path/" # # which allows you to create your own set of files by starting with the # /var/www/error/include/ files and # copying them to /your/include/path/, even on a per-VirtualHost basis. # Alias /error/ "/var/www/error/" <IfModule mod_negotiation.c> <IfModule mod_include.c> <Directory "/var/www/error"> AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en es de fr ForceLanguagePriority Prefer Fallback </Directory> # ErrorDocument 400 /error/HTTP_BAD_REQUEST.html.var # ErrorDocument 401 /error/HTTP_UNAUTHORIZED.html.var # ErrorDocument 403 /error/HTTP_FORBIDDEN.html.var # ErrorDocument 404 /error/HTTP_NOT_FOUND.html.var # ErrorDocument 405 /error/HTTP_METHOD_NOT_ALLOWED.html.var # ErrorDocument 408 /error/HTTP_REQUEST_TIME_OUT.html.var # ErrorDocument 410 /error/HTTP_GONE.html.var # ErrorDocument 411 /error/HTTP_LENGTH_REQUIRED.html.var # ErrorDocument 412 /error/HTTP_PRECONDITION_FAILED.html.var # ErrorDocument 413 /error/HTTP_REQUEST_ENTITY_TOO_LARGE.html.var # ErrorDocument 414 /error/HTTP_REQUEST_URI_TOO_LARGE.html.var # ErrorDocument 415 /error/HTTP_UNSUPPORTED_MEDIA_TYPE.html.var # ErrorDocument 500 /error/HTTP_INTERNAL_SERVER_ERROR.html.var # ErrorDocument 501 /error/HTTP_NOT_IMPLEMENTED.html.var # ErrorDocument 502 /error/HTTP_BAD_GATEWAY.html.var # ErrorDocument 503 /error/HTTP_SERVICE_UNAVAILABLE.html.var # ErrorDocument 506 /error/HTTP_VARIANT_ALSO_VARIES.html.var </IfModule> </IfModule> # # The following directives modify normal HTTP response behavior to # handle known problems with browser implementations. # BrowserMatch "Mozilla/2" nokeepalive BrowserMatch "MSIE 4\.0b2;" nokeepalive downgrade-1.0 force-response-1.0 BrowserMatch "RealPlayer 4\.0" force-response-1.0 BrowserMatch "Java/1\.0" force-response-1.0 BrowserMatch "JDK/1\.0" force-response-1.0 # # The following directive disables redirects on non-GET requests for # a directory that does not include the trailing slash. This fixes a # problem with Microsoft WebFolders which does not appropriately handle # redirects for folders with DAV methods. # Same deal with Apple's DAV filesystem and Gnome VFS support for DAV. # BrowserMatch "Microsoft Data Access Internet Publishing Provider" redirect-carefully BrowserMatch "MS FrontPage" redirect-carefully BrowserMatch "^WebDrive" redirect-carefully BrowserMatch "^WebDAVFS/1.[0123]" redirect-carefully BrowserMatch "^gnome-vfs/1.0" redirect-carefully BrowserMatch "^XML Spy" redirect-carefully BrowserMatch "^Dreamweaver-WebDAV-SCM1" redirect-carefully # # Allow server status reports generated by mod_status, # with the URL of http://servername/server-status # Change the ".example.com" to match your domain to enable. # #<Location /server-status> # SetHandler server-status # Order deny,allow # Deny from all # Allow from .example.com #</Location> # # Allow remote server configuration reports, with the URL of # http://servername/server-info (requires that mod_info.c be loaded). # Change the ".example.com" to match your domain to enable. # #<Location /server-info> # SetHandler server-info # Order deny,allow # Deny from all # Allow from .example.com #</Location> # # Proxy Server directives. Uncomment the following lines to # enable the proxy server: # #<IfModule mod_proxy.c> #ProxyRequests On # #<Proxy *> # Order deny,allow # Deny from all # Allow from .example.com #</Proxy> # # Enable/disable the handling of HTTP/1.1 "Via:" headers. # ("Full" adds the server version; "Block" removes all outgoing Via: headers) # Set to one of: Off | On | Full | Block # #ProxyVia On # # To enable a cache of proxied content, uncomment the following lines. # See http://httpd.apache.org/docs/2.2/mod/mod_cache.html for more details. # #<IfModule mod_disk_cache.c> # CacheEnable disk / # CacheRoot "/var/cache/mod_proxy" #</IfModule> # #</IfModule> # End of proxy directives. ### Section 3: Virtual Hosts # # VirtualHost: If you want to maintain multiple domains/hostnames on your # machine you can setup VirtualHost containers for them. Most configurations # use only name-based virtual hosts so the server doesn't need to worry about # IP addresses. This is indicated by the asterisks in the directives below. # # Please see the documentation at # <URL:http://httpd.apache.org/docs/2.2/vhosts/> # for further details before you try to setup virtual hosts. # # You may use the command line option '-S' to verify your virtual host # configuration. # # Use name-based virtual hosting. # NameVirtualHost *:80 # # NOTE: NameVirtualHost cannot be used without a port specifier # (e.g. :80) if mod_ssl is being used, due to the nature of the # SSL protocol. # # # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for requests without a known # server name. # #<VirtualHost *:80> # ServerAdmin [email protected] # DocumentRoot /www/docs/dummy-host.example.com # ServerName dummy-host.example.com # ErrorLog logs/dummy-host.example.com-error_log # CustomLog logs/dummy-host.example.com-access_log common #</VirtualHost> # domain: mysite.com # public: /home/websites/public_html/mysite.com/ <VirtualHost *:80> # Admin email, Server Name (domain name) and any aliases ServerAdmin [email protected] ServerName mysite.com ServerAlias www.mysite.com # Index file and Document Root (where the public files are located) DirectoryIndex index.html DocumentRoot /home/websites/public_html/mysite.com/public # Custom log file locations LogLevel warn ErrorLog /home/websites/public_html/mysite.com/log/error.log CustomLog /home/websites/public_html/mysite.com/log/access.log combined </VirtualHost>

  Read the article

• How to setup Hadoop cluster so that it accepts mapreduce jobs from remote computers?

  - by drasto

  There is a computer I use for Hadoop map/reduce testing. This computer runs 4 Linux virtual machines (using Oracle virtual box). Each of them has Cloudera with Hadoop (distribution c3u4) installed and serves as a node of Hadoop cluster. One of those 4 nodes is master node running namenode and jobtracker, others are slave nodes. Normally I use this cluster from local network for testing. However when I try to access it from another network I cannot send any jobs to it. The computer running Hadoop cluster has public IP and can be reached over internet for another services. For example I am able to get HDFS (namenode) administration site and map/reduce (jobtracker) administration site (on ports 50070 and 50030 respectively) from remote network. Also it is possible to use Hue. Ports 8020 and 8021 are both allowed. What is blocking my map/reduce job submits from reaching the cluster? Is there some setting that I must change first in order to be able to submit map/reduce jobs remotely? Here is my mapred-site.xml file: <configuration> <property> <name>mapred.job.tracker</name> <value>master:8021</value> </property> <!-- Enable Hue plugins --> <property> <name>mapred.jobtracker.plugins</name> <value>org.apache.hadoop.thriftfs.ThriftJobTrackerPlugin</value> <description>Comma-separated list of jobtracker plug-ins to be activated. </description> </property> <property> <name>jobtracker.thrift.address</name> <value>0.0.0.0:9290</value> </property> </configuration> And this is in /etc/hosts file: 192.168.1.15 master 192.168.1.14 slave1 192.168.1.13 slave2 192.168.1.9 slave3

  Read the article

• SSH Tunnel for Remote Desktop via Intermediary Server Part II

  - by Mihai Todor

  I asked previously how to configure 2 SSH tunnels using an intermediary server in order to run Remote Desktop through them and I managed to make it work. Now, I'm trying to do the same, using the same machines, but in reverse order. Here's the setup: Windows 7 PC in a private network, sitting behind a firewall. Public access Linux server, which has access to the PC. Windows 7 laptop, at home, on which I wish to do Remote Desktop from the PC. I use Putty on the laptop to create a reverse tunnel from it to the Linux server: R60666 localhost:3389. I use Putty on the PC to create a regular tunnel from it to the Linux server: L60666 localhost:60666. I SSH to the Linux sever and I run telnet localhost 60666 and it seems to produce the expected output, as described in the debugging tips that I received here. I try to connect Remote Desktop from the PC to the laptop: localhost:60666. It asks for my username and password, I click OK and it locks my current session on the laptop (so I see the welcome screen on the laptop instead of my desktop), it shows the "Welcome" message in the Remote Desktop screen and then it just goes black. It doesn't disconnect, it doesn't provide any error and I'm not able to perform any actions in the Remote Desktop screen. I tried the same setup with a Windows XP laptop and I'm experiencing the same symptoms. I also tried to use different ports than 60666, but nothing changed. Does anybody have any idea what I'm doing wrong? Update: As pointed out by @jwinders, I'm not able to run telnet PC 3389 from the Linux server directly. Since Windows Firewall has a rule to allow all connections on port 3389, I have no idea what is blocking it. Fortunately, I'm able to create a SSH tunnel from the Linux machine to the PC ssh 3389:localhost:3389 'domain\user'@PC.

  Read the article

• Allow anonymous upload for Vsftpd?

  - by user15318

  I need a basic FTP server on Linux (CentOS 5.5) without any security measure, since the server and the clients are located on a test LAN, not connected to the rest of the network, which itself uses non-routable IP's behind a NAT firewall with no incoming access to FTP. Some people recommend Vsftpd over PureFTPd or ProFTPd. No matter what I try, I can't get it to allow an anonymous user (ie. logging as "ftp" or "anonymous" and typing any string as password) to upload a file: # yum install vsftpd # mkdir /var/ftp/pub/upload # cat vsftpd.conf listen=YES anonymous_enable=YES local_enable=YES write_enable=YES xferlog_file=YES #anonymous users are restricted (chrooted) to anon_root #directory was created by root, hence owned by root.root anon_root=/var/ftp/pub/incoming anon_upload_enable=YES anon_mkdir_write_enable=YES #chroot_local_user=NO #chroot_list_enable=YES #chroot_list_file=/etc/vsftpd.chroot_list chown_uploads=YES When I log on from a client, here's what I get: 500 OOPS: cannot change directory:/var/ftp/pub/incoming I also tried "# chmod 777 /var/ftp/incoming/", but get the same error. Does someone know how to configure Vsftpd with minimum security? Thank you. Edit: SELinux is disabled and here are the file permissions: # cat /etc/sysconfig/selinux SELINUX=disabled SELINUXTYPE=targeted SETLOCALDEFS=0 # sestatus SELinux status: disabled # getenforce Disabled # grep ftp /etc/passwd ftp:x:14:50:FTP User:/var/ftp:/sbin/nologin # ll /var/ drwxr-xr-x 4 root root 4096 Mar 14 10:53 ftp # ll /var/ftp/ drwxrwxrwx 2 ftp ftp 4096 Mar 14 10:53 incoming drwxr-xr-x 3 ftp ftp 4096 Mar 14 11:29 pub Edit: latest vsftpd.conf: listen=YES local_enable=YES write_enable=YES xferlog_file=YES #anonymous users are restricted (chrooted) to anon_root anonymous_enable=YES anon_root=/var/ftp/pub/incoming anon_upload_enable=YES anon_mkdir_write_enable=YES #500 OOPS: bad bool value in config file for: chown_uploads chown_uploads=YES chown_username=ftp Edit: with trailing space removed from "chown_uploads", err 500 is solved, but anonymous still doesn't work: client> ./ftp server Connected to server. 220 (vsFTPd 2.0.5) Name (server:root): ftp 331 Please specify the password. Password: 500 OOPS: cannot change directory:/var/ftp/pub/incoming Login failed. ftp> bye With user "ftp" listed in /etc/passwd with home directory set to "/var/ftp" and access rights to /var/ftp set to "drwxr-xr-x" and /var/ftp/incoming to "drwxrwxrwx"...could it be due to PAM maybe? I don't find any FTP log file in /var/log to investigate. Edit: Here's a working configuration to let ftp/anonymous connect and upload files to /var/ftp: listen=YES anonymous_enable=YES write_enable=YES anon_upload_enable=YES anon_mkdir_write_enable=YES

  Read the article

• RDS, RDWeb, and RemoteApp: How to use public certificate for launching apps on session host?

  - by Bret Fisher

  Question: How do i tell RDWeb to launch apps from remote.domain.com rather then host.internaldomain.local? Environment: Existing org with AD forest. New single Server 2012 running all Remote Desktop Services roles for session host. Used the new 2012 wizard to setup "QuickSessionCollection" with roles: RD Session Host RD Connection Broker RD Gateway RD Web Access RD Licensing Everything works with self-signed cert, but we want to prevent those. The users are potentially non-domain machines so sticking a private root cert for on their machines isn't an option. Every part of the solution needs to use public cert. Added public remote.domain.com cert to all roles using Server Manager GUI: RD Connection Broker - Enable Single Sign On RD Connection Broker - Publishing RD Web Access RD Gateway So now everything works beautifully except the last step: user logs into https://remote.domain.com user clicks a app icon, which in background downloads a .rdp file that is signed by remote.domain.com. .rdp is set to use RD Gateway, which is remote.domain.com .rdp says app is hosted on internal host.internaldomain.local, which doesn't match the RDP-tcp TLS cert of remote.domain.com, and pops a warning. It's this last step that I'd like to fix. Is there a config option in PowerShell, WMI, or .config to tell RDWeb/RemoteApp to use remote.domain.com for all published apps so the TLS cert for RDP matches what the Session Host is using? NOTE: This question talks about this issue, and this answer mentions how you might fix it in 2008, but that GUI doesn't exist in 2012 for RemoteApp, and I can't find a PowerShell setting for it. NOTE: Here's a screenshot of the setting in 2008R2 that I need to change. It tells RemoteApp what to use for the Session Host server name. How can I set that in 2012?

  Read the article

• How to find out where or if MYSQL5 logs are stored on a machine WHM/Cpanel

  - by moi

  I have a WHM/Cpanel re-seller hosting account on a virtual private server (Linux). I have root access to the machine via SSH I am trying to locate a file that contains information that will help me to determine which users have accessed what db and from which hosts. I would imagine this kind of data is stored in a log file somewhere. The MySQL page says: The general query log - Established client connections and statements received from clients See: http://dev.mysql.com/doc/refman/5.0/en/server-logs.html It also says: By default, all log files are created in the mysqld data directory. So, I am am NOT asking where are the general query log logs stored, (cos I expect I will get answers saying "it depends") Please help me work out: "How can go about finding out where MySQL general query log logs are stored on a linux machine" Couple of things i've already tried: I looked at /etc/my.cnf it was a tiny file that only contained the following info: [mysqld] skip-bdb skip-innodb set-variable = max_connections=500 safe-show-database ~ ~ I have looked in: /var/lib/mysql/ But I could not see any log-like file names in that directory. Any clues on this would be most welcome.

  Read the article

• DNS "recursion not available" using a Cisco AnyConnect VPN connection

  - by codeape

  Does anyone have experience with configuring Cisco AnyConnect VPN? We have a problem with client DNS name resolution when connected over VPN. To me, it looks as if the Cisco AnyConnect VPN client intercepts DNS queries from the clients. Can someone confirm that the AnyConnect VPN client in fact does this (intercepts DNS traffic)? Where is this configured on the VPN server? EDIT: Here's how the routing table changes when I connect to the VPN: [~] $ diff -u /tmp/route_normal /tmp/route_vpn --- /tmp/route_normal 2010-01-20 19:23:47.000000000 +0100 +++ /tmp/route_vpn 2010-01-20 19:24:46.000000000 +0100 @@ -1,6 +1,10 @@ Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface +xxx.xxx.xx.xx.i 10.0.0.1 255.255.255.255 UGH 0 0 0 ath0 172.16.53.0 * 255.255.255.0 U 0 0 0 vmnet1 10.0.0.0 * 255.255.255.0 U 0 0 0 ath0 +172.17.20.0 * 255.255.255.0 U 0 0 0 cscotun 0 +192.168.111.0 172.17.20.212 255.255.255.0 UG 0 0 0 cscotun 0 172.16.140.0 * 255.255.255.0 U 0 0 0 vmnet8 +172.16.0.0 172.17.20.212 255.255.0.0 UG 0 0 0 cscotun 0 default 10.0.0.1 0.0.0.0 UG 0 0 0 ath0 EDIT 2: The IT guy has done "something" on the VPN endpoint. Now I get "recursion not available" when doing nslookup. The DNS servers have recursion enabled. So it must be the Cisco VPN DNS interception messing this up. ubuntu@domU-12-31-39-00-ED-14:~$ /opt/cisco/vpn/bin/vpn connect xxx.xxxxxx.xx ... >> Please enter your username and password ... >> notice: Establishing VPN... >> state: Connected >> notice: VPN session established to ... ubuntu@domU-12-31-39-00-ED-14:~$ nslookup www.vg.no ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server Server: 172.16.0.23 Address: 172.16.0.23#53 ** server can't find www.vg.no.compute-1.internal: REFUSED ubuntu@domU-12-31-39-00-ED-14:~$ ping 195.88.55.16 PING 195.88.55.16 (195.88.55.16) 56(84) bytes of data. 64 bytes from 195.88.55.16: icmp_seq=1 ttl=240 time=110 ms 64 bytes from 195.88.55.16: icmp_seq=2 ttl=240 time=111 ms 64 bytes from 195.88.55.16: icmp_seq=3 ttl=240 time=109 ms ^C --- 195.88.55.16 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2017ms rtt min/avg/max/mdev = 109.953/110.379/111.075/0.496 ms

  Read the article

< Previous Page | 803 804 805 806 807 808 809 810 811 812 813 814  | Next Page >