Search Results

Search found 20049 results on 802 pages for 'virtual drive'.

Page 81/802 | < Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88  | Next Page >

  • `power/persist` file not found in USB device sysfs directory

    - by intuited
    The file /usr/share/doc/linux-doc/usb/persist.txt.gz mentions that the USB-persist capability can be enabled for a given USB device by writing 1 to the file persist in that device's directory in /sys/bus/usb/devices/$device/power. This is said — if I understood correctly — to allow mountings of volumes on the drive to persist across power loss during suspend. However, I've discovered that the device I'd like to enable this facility for — a USB hard drive — does not have such a file in its corresponding directory, and that attempts to create it are rebuffed. Is there perhaps a kernel module that needs to be loaded for this to work? Do I need to build a custom kernel? I'm running ubuntu 10.10.

    Read the article

  • How to use BT or emule across 2 or more hard drives?

    - by the searcher
    One difficulty with BT or emule is that, when the hard drive is full, we constantly need to move older files to a new hard drive so that we can download newer files. We can change BT or emule's setting so that the folder for downloading points to the new hard drive, but then, what if emule haven't finished downloading for some files that are hard to find, and it is 92% done... in that case, we would like to keep the old setting so that when the last 8% arrives, it can go into the correct file. (and same for BT, if we haven't finished some file or if we want to seed something later). So is there a good way to let BT or emule point to 2 hard drives, or somehow let the new hard drive "merge" into the existing hard drive / folder?

    Read the article

  • Information about SATA, IDE (PATA) controllers

    - by Adam Matan
    I have a remote computer on which I want to install a new hard drive for rsync backup. The problem is, I don't know what controller technology is used (PATA, SATA, SATA2, ...) and how many available slots are left. I want to spare me an unnecessary drive just for opening the chassis and looking into wires. How do I query the SATA or PATA controllers? I'm interested in the following points: Which controllers exist in the machine How many (and which) disks are attached to each controller How many available slots are there

    Read the article

  • Microsoft Virtual Academy

    Carpe Diem It's been since a while that I could write an article for this blog but alas, I was (and still am) very busy with customer's work. Which is actually good. So, what is this article going to tell you? Well, in general, just what I already tweeted, that life is constant process of learning - especially as software craftsman. Due to an upcoming new customer project in ASP.NET I had to seize the opportunity to get my head deeper into latest available technologies, like Windows Azure and SQL Azure. I know... cloud computing and so on is not a recent development and already available since quite a while but I never any means to get myself into this since roughly two weeks ago. Microsoft Virtual Academy I can't remember exactly what guided me towards the Microsoft Virtual Academy (MVA), oh wait... Yes, it was a posting on Facebook from an old CLIP community friend. He posted a shortened URL with #MVA tag that caught my attention. Thanks for that Thomas Kuberek. After the usual sign in or registration via Live ID I was a little bit surprised that Mauritius is not an available country option... Quick mail exchange with the MVA Decan, and yeah, apologies for the missing entry. So, currently I'm learning about Microsoft products and services, and collecting points under "Not Listed Country" until Mauritius is going to be added. Hopefully soon, as MVA honors your effort with different knowledge ranks that are compared to other students with public profiles. I think it's a nice move to add some game and competition factor into the learning game. The tracks and their different modules are mainly references to publicly available material online, namely on either MSDN, TechNet, Channel9, or other Microsoft based sites. The course material therefore also varies in different media and formats, ranging from simple online articles over downloadable documents (.docx or .pdf) to Silverlight / Windows Media streams with download options. Self-assessment and students ranking Each module in a track can be finished by taking part in a self-assessment. Up to now, the assessment I did (and passed) were limited to 10 minutes available time, and consisted of six to seven questions on the module training material. Nothing too serious but it gives you a glimpse idea how Microsoft certification exams are structured. Conclusion Nothing really new but nicely gathered, assembled and presented to the MVA students. At the moment, I wouldn't dare to compare the richness and quality of those courses with professional training offers, like Pluralsight .NET Training, LearnDevNow, VTC, etc. at all, but I think that MVA has potential. Give it a try, and let me know about your opinions.

    Read the article

  • best data+partition recovery software

    - by Pennf0lio
    I accidentally formatted my Drive D that contained all my Backups and Documents. I separated my files to my Drive D hoping I will not harm my files. Since I use Acronis Recovery to Install a new OS with some pre-installed application to my HDD I didn't realize I also formated/erase my Drive D. Now my drive D is unpartitioned. I am really in really in deep trouble and would need some urgent help, Please recommend a Software that at least can restore my Old Drive that contained my files. I'm assuming most of you think this is a duplicate of some old questions here, But I'm not looking for data recovery, I need to recover the whole partition with the files. I used to use "Recuva" but It only recovers files not the whole folders with the files in it. Please advice. Thank You!

    Read the article

  • Windows7 Gone after Ubuntu dual boot install

    - by Adi
    I had a very hard time to dual boot install Ubuntu 12.04 Apparently, Ubuntu has restriction of 4 partitions and I already had 4, so it just couldn't recognise my partitions. This was something I realised too late, but finally got to install Ubuntu. Now, even though Windows 7 option is listed when I try to boot my laptop, it doesn't really let me boot and just loops back to begin. I tried windows repair DVD also, didn't work. I was fine with complete fresh install of windows too, but Windows CD didn't detect my Hard Disk Drive or any partitions (even though the original C drive with Windows is still an NTFS partition, according to gParted, and I can access the data from same using Ubuntu log in). My Ubuntu works fine, but I need windows log in also. Any suggestions anyone?

    Read the article

  • CMT Blog: Virtual IO gets better for LDoms

    - by uwes
    As we all know virtual IO is of great use in the IT environments of today but when it comes to performance we often have to pay the price. In his Blog entry Improved vDisk Performance for Ldoms, Stefan Hinker explained how the new implementation of the vdisk/vds software stack in Solaris 11.1 SRU 19 (and a Solaris 10 patch sortly afterwards) significantly improves latency and throughput of the vitual disk IO.

    Read the article

  • "merging" multiple hardrives for Ubuntu 14.04 install

    - by Thijser
    I have 3 hardrives inside my laptop 2 of which currently house other opperating systems but have a empty partitions of 8 and 9 gigabye and the third is just 12 gB (currently not partitioned at all). Now each of these 3 is to small to be useful to me, however combined they are 29gigs which can easily hold a ubuntu installation, and associated programs. Is there a way set up my installation in such a way that it threads these 3 disks as one? Or is there a way by which I can make it default storage of many things into one drive (downloads and sudo apt-get install for example) to one drive while keeping ubuntu onto another?

    Read the article

  • Use Entitlements To Secure LDAP-enabled Applications With Oracle Virtual Directory and Oracle Entitl

    - by mark.wilcox
    I stumbled on an interesting article  that shows how the author used OVD to exposed OES security to protect a portal that only understood LDAP group-based authorization.This is great because it shows how you can use OES today to build central policies that can be used without needing to rewrite all of your applications - in particular if you just want to leverage rule-based groups.  Posted via email from Virtual Identity Dialogue

    Read the article

  • Live Virtual Class for Partners: Application Management

    - by Patrick Rood
    v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} November 11-12th Manageability Partner Community Application Management Suite Live Virtual Training This training will be offered to Oracle Partners over a live webcast during business hours. Each day will consist of approximately 2-3 hours of lecture/demos. It will be recorded and available for playback. Purpose: This virtual course is a comprehensive program of training sessions, prepared and presented by Product Managers. This ensures you have all the information you need to position and sell Oracle Application Management Suites. The sessions will be lecture based with demonstrations to complement. These sessions are interactive and everyone will be required to participate. Customer case studies will be used as appropriate and there will be plenty of opportunity for in-depth discussion. Please bring to the training an understanding of what Enterprise Manager 12c does for our customers, along with your own experiences to date. Logistics: Topic: Oracle Application Management Suite Training (2 Days - approx 2-3 Hour per Day) WebEx session details to be provided upon registration. Monday 11th November | 14:00PM GMT | 18:00PM Gulf (GMT+4) Tuesday 12th November | 14:00PM GMT | 18:00PM Gulf (GMT+4) (Back to the top) Copyright © 2012, Oracle. All rights reserved. Contact Us | Legal Notices and Terms of Use | Privacy Statement Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";}

    Read the article

  • "The disk drive for / is not ready yet or not present" message on boot

    - by MHS
    After upgrading my Ubuntu machine from ver. 11.10 to 12.04, I get the following error and the machine stop working before any graphical environment: ** (plymouthd:357): WARNING **: Command line `dbus-launch --autolaunch=530c973a1fe4d1e1e6bd... --binary-syntax --close-stderr' exited with non-zero exit status 1: Autolaunch error: X11 initialization failed.\n udevd[397]: specified group 'colord' unknown The disk drive for / is not ready yet or not present. Continue to wait, or Press S to skip mounting or M for manual recovery. Any help appreciated.

    Read the article

  • changing drive nodes & hdparm

    - by Kalamalka Kid
    I am currently attempting to create a command that works at startup to kill the power on two of my very noisy hard drives. I have edited the etc/rc.local file to include this command: sudo hdparm -y /dev/sdc sudo hdparm -y /dev/sdd exit 0 While I think this should work, it seems the allocated drives keep switching around every time I reboot. I have sda, sdb, sdc, sdd, and sde but they keep getting jumbled around (making the drive I wish to shut different than sdd which is making the task of shutting down the right drive on start-up quite cumbersome. I had a perfectly functioning ftstab file working which disappeard, but I restored it from the back up into the etc/ dir: # <file system> <mount point> <type> <options> <dump> <pass> #Entry for /dev/sda1 : UUID=43c09daf-08a5-44f2-89b0-fc7c6f0d1e67 / ext4 errors=remount-ro 0 1 #Entry for /dev/sdd1 : UUID=443AFBAD7FE50945 /media/DX100 ntfs-3g defaults,nosuid,nodev,locale=en_CA.UTF-8 0 0 #Entry for /dev/sdb1 : UUID=FCE456F5E456B21E /media/GalaxyM83 ntfs-3g defaults,nosuid,nodev,locale=en_CA.UTF-8 0 0 #Entry for /dev/sdf1 : UUID=1CA057FDA057DBB8 /media/Holideck ntfs-3g defaults,nosuid,nodev,locale=en_CA.UTF-8 0 0 #Entry for /dev/sdc1 : UUID=7ABB49654B799D40 /media/JX3P ntfs defaults,nosuid,nodev,locale=en_CA.UTF-8 0 0 it seems every time I boot the order of the drives changes. I do not know how to resolve this. A quick workaround the problem was to go with UUID instead of the DEV letter by editing the etc/rc.local file to include: hdparm -y /dev/disk/by-uuid/443AFBAD7FE50945 hdparm -y /dev/disk/by-uuid/7ABB49654B799D40 So I thought I was in the clear, as I heard both hard drives die down during the boot sequence, BUT, as soon as I log in both drives start up again! so now I have to figure out what is making them start up again after log in, or perhaps another way to get them to turn off. Is there some kind of command i can get to execute after log in? I tried editing the startup applications to include an autossh with: autoshh - sudo hdparm -y /dev/disk/by-uuid/7ABB49654B799D40 autoshh - sudo hdparm -y /dev/disk/by-uuid/443AFBAD7FE50945 but this did not seem to work to turn off the disks after log in.

    Read the article

  • Don't Miss Oracle UPK at the Oracle Applications Virtual Tradeshow

    - by di.seghposs(at)oracle.com
    Be sure to visit the Oracle Applications Virtual Tradeshow - Spotlight on Customer Success - February 3, 2011. If you are considering using Oracle UPK for a project or an upgrade, this is an event you don't want to miss. Hear how the City and County of San Francisco used Oracle UPK for their successful PeopleSoft upgrade. Get a chance to meet the experts and listen to 20+ customers share their success with Oracle Applications. Register Now!

    Read the article

  • Hard Drive Formatting and Unmounting Errors

    - by Lucas Carther
    I'm trying to format a hard drive using Ubuntu 11.10. Every time that I attempt to format it from the Disk Utility, I get the error saying the device is busy, and under details it says: /dev/sda1 is mounted Then when I try to unmount it from the disk utility, it shows that the operation has failed and says: Error unmounting: umount exited with exit code 1: helper failed with: umount: only root can unmount UUID=70D6-1701 from /boot/efi

    Read the article

  • Retro Ad – 10 MB Hard-Drive for $3398 [Image]

    - by Asian Angel
    This is definitely one hard-drive (and price) that you will not be feeling nostalgic over! View the Full-Size Version of the Ad (Image) The Hard Disk you’ve been waiting for. [via Fail Desk] Why Enabling “Do Not Track” Doesn’t Stop You From Being Tracked HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference

    Read the article

  • Install Ubuntu or Kubuntu on a External USB Drive

    - by rihatum
    Hi All, I have a few external hard drives (SSDs and Platters (SATA), is this possible that I can install Kubuntu 10.10 x64 or Ubuntu 10.10 x64 onto one of these external hard drives? My System supports booting off a usb, it will just give me a learning playground without spoiling my existing operating environment. I know I can install as Virtual machines, but installing U/Kubuntu on a External HDD and booting off it would be easier. Will be grateful for your insights....and steps to do so. Thanks

    Read the article

  • Looking for a free or open-source burner emulator [closed]

    - by Jared Harley
    Possible Duplicate: Virtual CDR driver I am looking for a free or open-source virtual CD/DVD emulator to run in a Windows environment. What I want is similar to what SlySoft's Virtual Clone Drive or Daemon Tools provides, but the emulated drive needs to be a burner of some type. The burner should be able to save disc images (.iso, .ccd, etc) to my harddrive - basically, the same as if I burned the files to a CD-R, and then ripped them back to a disc image. I have already looked around some and come across 2 - DVD neXt COPY iTurns and NoteBurner M4P. Both of these programs create a virtual CD-RW drive, but they are integrated into their product (for burning from iTunes to create mp3 files) and cannot create disc images. I am currently writing a piece of software that will have the capability to burn disc images onto CDs/DVDs, and I don't want to end up with a 100 coasters while I'm testing my software. Anyone have any ideas? Related ServerFault queston: Create netbook recovery image without DVD burner (virtual burner?)

    Read the article

  • Cloning a dual boot system from HDD to SSD

    - by Alex
    I'm planning on replacing my laptop's HDD with a 256GB SSD, but I have a dual-boot (12.04 and Windows 7) setup and I'd like to be able to directly migrate Ubuntu over without having to reinstall and lose all of my settings. GParted reports the following partition setup on my HDD. I am, of course, able to modify it if necessary. /dev/sda1 (NTFS) 66.92 out of 200.00 MB used I'm honestly not sure what this partition is for. Maybe for Windows 7 system files? I'm hesitant to mess with it. (edit; it turns out it is a partition for Windows recovery files in the event of OS corruption, so I don't want to remove it. Plus it also appears to be a major pain to remove anyways) /dev/sda2 (NTFS) 116.35 out of 339.06 GB used (boot) This partition is the C:/ drive on my Windows installation. I don't use it on my Ubuntu installation, except it is the boot partition and thus has grub on it. /dev/sda4 (extended) > /dev/sda5 (ext4) 14.49 out of 91.34 GB used > /dev/sda6 (linux-swap) 5.92 GB These are my Ubuntu partitions. /sda5 contains my documents and all of the files I use on Ubuntu, and (as far as I know) the system files for Ubuntu itself (it's the partition I created when prompted by the Live-DVD installer). /sda6 is, of course, the swap partition which I only need for hibernation (6GB of RAM). /dev/sda3 (NTFS) 9.89 out of 14.75 GB used This is an annoying partition that Lenovo created to store some drivers and files that I might need later on. For example, it allows me to use OneKeyRecovery for a quick factory recovery if absolutely necessary, not sure if that'll work on an SSD. It also contains not-so-important files for bloatware installation. In total, my HDD only has about 150GB of files on it so it should fit comfortably on the SSD. The problem is, I want to exactly migrate my files, partitions, OSes, MBR, etc. from my HDD to my SSD and I'm not quite sure how to do this. I've seen CloneZilla referenced before, but I'm not all too experienced and the documentation for it quite frankly seems a bit like a foreign language to me. So, put simply, is there any way I can exactly clone this HDD to an SSD without a massive headache? Also, if it matters, I'll probably be using an external hard drive case (as recommended in online tutorials) to externally attach the SSD to my laptop during the cloning process due to the lack of two hard drive slots in the machine.

    Read the article

  • Virtual Server Hosting Services in India

    There is no shortage of virtual server hosting service providers in India and each one of them is an expert in his job and domain. They offer both Linux and Windows VPS hosting plans apart from deali... [Author: John Anthony - Web Design and Development - May 18, 2010]

    Read the article

  • How USB drives goes after system hard drives

    - by raihanchy
    I am using Ubuntu 12.04 LTS. My hard drives usually comes as: sda, with 'sudo blkid' and if I plug-in any USB drive, they comes as: sdb, sdc etc; after sda. That's fine!!! But problem arises after I restart my laptop with connecting those USB drives. They alter and comes first and hard drive goes to the end, like: 'sudo blkid' shows, sda, sdb for USB drives and sdc for hard drives. It's making problem to mount with /etc/fstab. I couldn't find any solutions for this. I would like to have any USB drives after my system hard drives, as in Windows. Please, help me at this point. Thanking you. Raihan

    Read the article

  • Disk drive for / not ready on boot after upgrade from 10.04 to 12.04

    - by Mathieu M-Gosselin
    After upgrading (using the Upgrade button from the update manager) from 10.04.4 to 12.04.1, I cannot boot anymore. Upon booting, I am greeted with the Ubuntu logo and the error "The disk drive for / is not ready yet or not present". I have the option to wait, to skip and to access a basic shell. Waiting overnight did nothing, skipping just gives me the same error for /tmp, /home, then for a UUID and finally it just goes to a black screen with a white "_" in the top left corner. My setup is a dual boot one with XP on a single hard drive, I use separate partitions for / and /home. Back in the day I installed 8.04 directly from the CD while leaving a partition for XP, which I installed after. This setup had never caused any such issues, even when upgrading from 8.04 to 10.04. I have done plenty of research regarding this issue, as many others seem to have had similar issues after doing the same upgrade as me. However, while for most what fixed the problem was running: apt-get -f install after remounting / in read-write, it didn't do it for me. I got dependency errors (see here), which I also investigated. I found https://bugs.launchpad.net/ubuntu/+source/python-defaults/+bug/990740 where most people say the solution that worked is (prior to running the above command) running: apt-get install -o APT::Immediate-Configure=false -f apt python-minimal but that also got me a lot of dependencies errors as output (see here), similar to #34 in the above thread. I also read that running: dpkg --configure -a could help, at first it wouldn't run because it had trouble parsing /var/lib/dpkg/status since there was an extra blank line in a package description (see https://bugs.launchpad.net/ubuntu/+source/dpkg/+bug/916799) but I removed it using vim (and then reran the command). It still gives me output that looks like an error, though. Here it is: http://paste.ubuntu.com/1338074/. I also tried re-running the above apt-get commands after that, to no avail. I'm running out of things to try in the hope of getting this fixed, your help would be very much appreciated! Thank you in advance.

    Read the article

  • Information about SATA, IDE (PATA) controllers

    - by Adam Matan
    I have a remote computer on which I want to install a new hard drive for rsync backup. The problem is, I don't know what controller technology is used (PATA, SATA, SATA2, ...) and how many available slots are left. I want to spare me an unnecessary drive just for opening the chassis and looking into wires. How do I query the SATA or PATA controllers? I'm interested in the following points: Which controllers exist in the machine How many (and which) disks are attached to each controller How many available slots are there

    Read the article

< Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88  | Next Page >