Search Results

Search found 2583 results on 104 pages for 'ping'.

Page 82/104 | < Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >

• Openfiler iSCSI performance

  - by Justin

  Hoping someone can point me in the right direction with some iSCSI performance issues I'm having. I'm running Openfiler 2.99 on an older ProLiant DL360 G5. Dual Xeon processor, 6GB ECC RAM, Intel Gigabit Server NIC, SAS controller with and 3 10K SAS drives in a RAID 5. When I run a simple write test from the box directly the performance is very good: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 4.64468 s, 226 MB/s So I created a LUN, attached it to another box I have running ESXi 5.1 (Core i7 2600k, 16GB RAM, Intel Gigabit Server NIC) and created a new datastore. Once I created the datastore I was able to create and start a VM running CentOS with 2GB of RAM and 16GB of disk space. The OS installed fine and I'm able to use it but when I ran the same test inside the VM I get dramatically different results: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 26.8786 s, 39.0 MB/s [root@localhost ~]# Both servers have brand new Intel Server NIC's and I have Jumbo Frames enabled on the switch, the openfiler box as well as the VMKernel adapter on the ESXi box. I can confirm this is set up properly by using the vmkping command from the ESXi host: ~ # vmkping 10.0.0.1 -s 9000 PING 10.0.0.1 (10.0.0.1): 9000 data bytes 9008 bytes from 10.0.0.1: icmp_seq=0 ttl=64 time=0.533 ms 9008 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.736 ms 9008 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.570 ms The only thing I haven't tried as far as networking goes is bonding two interfaces together. I'm open to trying that down the road but for now I am trying to keep things simple. I know this is a pretty modest setup and I'm not expecting top notch performance but I would like to see 90-100MB/s. Any ideas?

  Read the article

• Cisco SG200 vlan issue in ESXi VSA cluster

  - by George

  I have three Cisco SG200-26 switches, and I also have two ESXi hosts that I have connected like shown in the below "best practice" map by VMware: http://communities.vmware.com/servlet/JiveServlet/previewBody/17393-102-1-22458/VSA_networking_map.pdf Even though I created the VLANs in the SG200 and I set the two VLANs (508 and 608) as allowed for these untagged ports (where my ESX NIC's are connected), I can not ping from host 1 to host 2 when configuring the NIC's to use 608 VLAN. Am I missing something? my IP's are all in the 192.168. range, and the only reason I need the VLANs is to isolate the traffic of VSA back-end internally, only the two hosts will be using the VLANs. So I think I do not have to create virtual interfaces on my router since that's the case, is my understanding correct? Also sending my switch config screenshot below.. all 3 switches have the latest firmware (it seems these were originally linksys and got rebranded as cisco after the acquisition) http://img31.imageshack.us/img31/2503/switch.gif Any ideas what to change on the Cisco SG200 to make this work , would be appreciated! The second VLAN (608) only needs two IP's: 192.168.0.1 and 192.168.0.2 The first VLAN (508) will have about 15 IP's for ESXi Management and VSA cluster service, I could use either 192.168.1.xx or 10.0.1.xx The rest of my network (about 50 clients) is in 192.168.1.xx range VMware also states that the VLAN protocol on the physical switch must be 802.1Q, not ISL, anyone knows which of the two my SG200-26 uses? In addition to that, the only requirement from VSA is that my two hosts: -Are in the same subnet. -Have static IP addresses set. -Have the same Default Gateway configured. If I need inter-vlan routing for this, I suppose I have to create virtual interfaces on my sonicwall, and assign an IP for each VLAN, and then set routes between them? Thank you for your time!

  Read the article

• Plesk wildcard subdomain not working

  - by avdgaag

  I'm trying to set up a wildcard subdomain on my VPS. Ultimately I want to end up with this: main site: my.domain.tld subdomain: sub1.my.domain.tld - should end up serving my.domain.tld/sub1 I am using plesk 8.6. I have created a DNS A record pointing at my VPS' IP. I have then restarted the DNS server and waited up to 24 hours. But trying ping sub1.my.domain.tld results in an unknown host error. So I know there's more stuff involved, configuring apache etc. But so far, I cannot even get the subdomain working at all, let alone serve up the right content. I have also tried a CNAME record, to no effect. I have also tried creating a regular subdomain with a fixed name, which also does not work. Pre-configured subdomains DO work, like ftp.my.domain.tld or mail.my.domain.tld. I am clearly missing something here, but my hosting provider charges a small fortune for any support request not involving hardware physically burning down, so I'm hesitant to ask them. Any ideas?

  Read the article

• Is there any way to abstract IP address during ssh?

  - by Vivek V K

  I have a server which is in the middle of a forest. It is connected to the Internet via a microwave link and an ADSL link.Hence it has two different static IP addresses. Now if there is heavy rain, the microwave link breaks and I should use the much slower ADSL link. And I ping the microwave ip time to time to check if it is up again . But at times, I end up using the very slow ADSL link even if the microwave link is back up. Hence I need a way to automate this in the following way. 1.I need to abstract the IP address of the machine with some other name which when I use ssh or sftp, will poll both the IP and connect me to the best one. so for eg: if I say ssh -Y name@server, It should first try to connect to the microwave link if it cant, then connect to ADSL. 2.Suppose the first time I connect, the microwave link is down so it connects to ADSL, I need it to dynamically change to the microwave link once it is working again. Is this even possible?

  Read the article

• Can't make virtual host working

  - by sica07

  I have to create a virtual host on a server which, previously hosted a single website (domain name). Now I'm trying to add a second domain on this server (using the same nameserver). What I've done so far: Initially there was no virtual host so I've made one for the second domain: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /var/www/bla ServerName www.blabla.com ServerAlias blabla.com <Directory /var/www/blabla> Order deny,allow Allow from all AllowOverride All </Directory> </VirtualHost *:80> Because nothing happend, I changed the DocumentRoot of the apache server to /var/www (initially was the root document of the first website -/var/www/html) and created a virtual host for the first domain too: <VirtualHost *:80> DocumentRoot /var/www/html ServerName www.first.com ServerAlias first.com <Directory /var/www/html> Order deny,allow Allow from all AllowOverride All </Directory> </VirtualHost *:80> In this case, first.com is working ok, but bla.com not. When I ping blabla.com I get the "unkown host" response. What am I doing wrong? Do I have to modify something in the DNS settings too? Thank you.

  Read the article

• DD-WRT PPTP VPN problem

  - by Tobias Tromm

  I try to configure a DD-WRT as a PPTP client. The VPN Server is Windows Server 2003. This is my scenario: The Windows 2003 Server has set to give to the VPN Client the 10.0.0.81 fixed IP and to add a network route to the remote home. At the remote home I have changed the PPTP Options at DD-WRT to make the connection. The VPN connection is successfully established. ...and Windows successfully add the route to the remote home 192.168.2.X. From the remote home I can successfully access any computer from the VPN server side. The problem is when I try to access the remote home from the Server side. From Server side I only can access\ping DD-WRT ( by VPN Client IP - 10.0.0.81). What's wrong? How I need to do to be a site-to-site VPN? This is what happen when I try to tracert the remote home from local home.

  Read the article

• How to fix a Postfix/MySQL/Dovecot Unknown Host Issue?

  - by thiesdiggity

  I am having an issue with one of my Postfix/Dovecot mail servers and I'm unsure how to fix the problem. I will try to explain it in detail, here it goes: I have an Ubuntu server setup using Virtual hosting with Postfix, Dovecot and MySQL. We have one domain setup as a virtual domain, for this example I am going to use mail.example.com. Under that domain we have one email address. I have another server (MS Exchange) setup using another one of my sub-domains, ex.example.com. The problem is that when I SMTP into the account on mail.example.com and try to send an email to an account on ex.example.com, I get the email returned back to us with an "unknown host" error. Now, I know that the mail.example.com server can resolve the ex.example.com domain because I can ping/dig while SSH'd into it. I can also log into Postfix via Telnet and send an email to an ex.example.com mailbox. I'm guessing that it has something to do with Postfix/Dovecot looking locally for the domain in the virtual domain list because of the tld domain (example.com)? If that's the case, how do I get Postfix/Dovecot to only look locally for the entire URL (mail.example.com) and if it doesn't find it, send it to the correct server by looking up the MX/A records (which I know exist and are setup correctly)? I have been working on this all day and any guidance would be GREATLY appreciated! Thanks for your time!

  Read the article

• How can a CentOS 6 guest running in VirtualBox be configured as a LAMP server that can be accessed from the Windows host?

  - by jtt89

  I was able to conect Centos6 on Virtual Box to Windows (I can ping in both directions) with Host-only Adapter (for connection between the two) and NAT Adapter (to enable Linux on VB to connect to the Internet). I want to set up httpd, mysql and vsftpd servers and in the end easily connect to httpd from Windows based browser and ftp server with a Windows based client as well. I would also want to have access through SSH. I have a general idea of the steps that are involved, but there is also a configuration that I am not sure about at this point. Lets say I follow these steps: yum install httpd yum install php php-pear php-mysql yum install mysql-server mysql_secure_installation yum install vsftpd yum install mod_ssl Technically I have everything installed, but what would be the next steps that I need to take (from the networking point of view, so to speak) to get it all working)? I know I need to configure, at least Apache, and ftp server, but I am not sure how is it gonna work; like where am I gonna be uloading the sites (I know this can vary), how am I gonna know what address to use in a browser if I wanna go to a website x, y, z on that installation etc. This sounds like I need to do some kind of DNS setup and I am kind of stuck at this point. If somebody could give me a general outline of what are the things that need to be done that would be great (I was looking at a lot of websites and I know about etc/sysconfig/network, httpd.config - not too much about it on Apache's site, hostname, hostname -f etc; but it is kind of hard to piece it all together at this point). I am gonna be looking at the books also, but they not always reflect the setup that I have too (VirtualBox). Thank you.

  Read the article

• Wifi Drops Connections with WPA2-PSK

  - by graf_ignotiev

  I run a small computer lab made up of 10 computers of identical hardware and software (Dell Latitudes with Windows 7 x64 Enterprise) and I use a ZyWALL 2WG as a router/firewall. Nine of the computers connect to the router over wifi using WPA2-PSK encryption while the last one is connected by ethernet cable. I'm having a problem where any computer connected to the wi-fi occasionally drops off the network (it cannot be pinged and the client cannot ping the gateway). It only happens on the wifi side and only when the encryption is WPA2-PSK or WPA-PSK. I tried using another router with a different make and model and had no problems. Thinking it could be a software error, I reset the router to factory defaults and installed the newest firmware (V4.04(AQI.8) | 04/09/2010), but still have the problem. The 802.1X log gives the following error User logout because of user disassociation. with this note WPA2-PSK:00242c582ece:logout where 00242c582ece is the mac address of the device. At this point I'm out of things to try and leads to follow. It looks like this user had the same or similar problem, but none of those proposed solutions work for me.

  Read the article

• How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

  - by Annonomus Penguin

  I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can bypass this by setting the main radio as a client to the main router, and adding a virtual radio configured as an AP. You can then set up the credentials for connecting to the main router and allowing devices to connect to the repeater/router. I have a few devices on my network: Ethernet computers Server with Samba running WiFi devices connected to the main router I then wanted to add a repeater. I have a couple of other things on the repeater: WiFi Computer Other WiFi devices. Anyway, I wanted to connect my WiFi computer to the share on my server via Samba. However, for some reason, my router treats the main router as WAN, not another device. I've tried disabling the SPI firewall: However, that doesn't work. I've tried pinging my WiFi computer from my server. However, I can ping my server from my WiFi computer. AFAIK, they are on the same subset, just using different IPs: the main one uses 192.168.0.x and the repeater uses 192.168.1.x (starting at 100 for some reason). It seems as I need to configure my router(s) to work together for DHCP. I noticed there was a "DHCP forwarder" option, but I have no idea what that would do. A quick note: for some reason (that's beyond me) my ISP disabled the capability to bridge a WiFi to ethernet connection with the router they provide (something about PPPoE or similar...). The service rep I talked to when I was having issues after I changed ISPs said that, but they couldn't explain exactly what they were "blocking." How can I get DD-WRT to not treat the client connection as WAN and the router to recognize the devices connected to the repeater?

  Read the article

• How to kill unkillable Python-processes running as root

  - by Andrei

  I am experiencing an annoying problem with sshuttle running it on 10.7.3, MBA with the latest firmware update -- after I stop it (ctrl+c twice), or loose connection, or close the lid, I cannot restore it until I restart the system. The restarting takes notably more time, than it would normally take. I have tried to flush ipfw rules - not helping. Could you advice me how to restore sshuttle connection (without restarting os)? The following processes remain running as root, which I do not know how to kill (tried sudo kill -9 <pid> with no luck): root 14464 python ./main.py python -v -v --firewall 12296 12296 root 14396 python ./main.py python -v -v --firewall 12297 12297 root 14306 python ./main.py python -v -v --firewall 12298 12298 root 3678 python ./main.py python -v -v --firewall 12299 12299 root 2263 python ./main.py python -v -v --firewall 12300 12300 The command I use to run proxy: ./sshuttle --dns -r [email protected] 10.0.0.0/8 -vv The last message I get trying to restore the connection: ... firewall manager: starting transproxy. s: Ready: 1 r=[4] w=[] x=[] s: < channel=0 cmd=PING len=7 s: > channel=0 cmd=PONG len=7 (fullness=554) s: mux wrote: 15/15 s: Waiting: 1 r=[4] w=[] x=[] (fullness=561/0) >> ipfw -q add 12300 check-state ip from any to any >> ipfw -q add 12300 skipto 12301 tcp from any to 127.0.0.0/8 >> ipfw -q add 12300 fwd 127.0.0.1,12300 tcp from any to 10.0.0.0/8 not ipttl 42 keep-state setup >> ipfw -q add 12300 divert 12300 udp from any to 10.0.1.1/32 53 not ipttl 42 >> ipfw -q add 12300 divert 12300 udp from any 12300 to any not ipttl 42 Update: $ ps -ax|grep python 1611 ?? 0:06.49 python ./main.py python -v -v --firewall 12300 12300 48844 ?? 0:00.05 python ./main.py python -v -v --firewall 12299 12299 49538 ttys000 0:00.00 grep python

  Read the article

• Using Virtualbox Bridge Networking fails connection from Guest OS to Oracle XE running on Host

  - by Licheng

  I am trying to make a JDBC connection from a VirtualBox Ubuntu Guest OS to an Oracle XE database running o Host. However, the connection is refused. Here are the details of my environment: VirtualBox: 4.1.4 Host OS: Windows 7 Guest OS: Ubuntu server 11.4 Networking mode: Bridged network Oracle XE database running on Host Issue: WebLogic server runs on the Ubuntu virtualbox. It attempts to connect to an Oracle XE database running on the Host OS (windows 7) with listening port 1521. On the Guest OS (Ubuntu), I am able to ping the Host computer from the Guest OS. However, when I configured a JDBC data source on the WebLogic server on the Guest OS to connect to the Oracle XE, connection took a long time, and eventually I received an "IO Exception: The Network Adapter could not establish the connection". When I tried "telnet host-ip 1521", no connection was established. With Bridge networking, I can make bi-directional connections between the host and the guest OS (e.g. connection through ssh and ftp). Is there anything I missed in the setup of Bridge networking and the guest/host OS? Note that I was able to make the same connection within a normal networking environment (i.e. not using virtual box). I am not sure whether Bridge networking is a good option for the work described above. Should I use host-only networking mode? If so, any specific configurations I need to perform? I read through the Virtual box document on setting up the host-only network, however, it lacks of details. I followed the procedures described in the manual, and couldn't even connect to the host. Could some experts here enlighten me on this issue? Much appreciated. Licheng

  Read the article

• SQL Server 2008 cluster freezing

  - by Ed Leighton-Dick

  We have run into a strange situation in which a SQL Server 2008 single-node cluster hangs. As background, we are rebuilding a Windows Server 2003/SQL Server 2005 two-node cluster using Windows 2008 and SQL Server 2008. Here's the timeline: Evicted the passive node (server B) from the Windows 2003/SQL 2005 cluster. The active node now functions as a single-node cluster with no problems. Wiped server B's disks and installed Windows 2008 and SQL Server 2008 as a single-node cluster. Since we do not want to the two clusters to communicate yet, we left the cluster's private network "heartbeat" adapter unconfigured. The cluster comes up and functions normally. Moved all databases to the new cluster. Cluster continues to function normally. Turned off server A (old cluster) in preparation for rebuilding as the second node of the new cluster. SQL Server instance on server B (new cluster) locks up, even though it should have no knowledge of or interaction with server A. Restarted server A. SQL Server instance on server B (new cluster) immediately begins working again. Things we have tried: The new cluster's name responds to ping and NETBIOS requests, even while the SQL Server is hung. We have confirmed that no IP address is assigned to the old heartbeat adapter, and it is not pulling an IP address from DHCP. Disabling the heartbeat's network card has the same effect. No errors were generated in any logs - Windows or SQL. When the error first occurred, it sat in the hung state for quite some time (well over 10 minutes) before anyone figured out what was going on. This would seem to eliminate any sort of normal cluster timeout in which it would have been searching for the other node (even if one had been configured). Server B is running Windows 2008 SP2, fully patched, and SQL Server 2008 SP1 CU7 (10.0.2775).

  Read the article

• Linux on Sony Vaio VPCEB1S1E

  - by Jaakko

  I bought Sony Vaio VPCEB1S1E and I was able to surf on net. Then I tried to install Ubuntu 9.04 and Linux Mint on it but neither allows me an access to the Internet. How can I configure Mint so that I can go to net and get updates via apt-get? jaakko@jaakko-laptop ~ $ ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 46:83:d4:f4:36:bc BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 78:dd:08:c5:61:88 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster0 Link encap:UNSPEC HWaddr 78-DD-08-C5-61-88-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) jaakko@jaakko-laptop ~ $ ping 8.8.8.8 connect: Network is unreachable

  Read the article

• Active Directory Domain Services - Network Name Cannot be Found

  - by Arief

  I have really weird problem that I could not explain. I am trying to redirect all users home folder to the new server. I have copied all the files including the permissions to the new server. All I need to do is to update the user profile for home folder by changing the server name. However, I got this message when I enter the new server name: My server that serving as AD can resolve the name by ping and nslookup of the server name. The only thing that I don't understand why the MMC cannot resolve the name. I did change with the IP Address and I still get the same error message. Thank you so much for your help. UPDATE: I know what seems to be a problem, but I don't know how to fix it. The new server that will serve all Home folder is actually sitting in the cloud with different IP Address as the Domain Controller. The Domain Controller is sitting locally in the office with 10.0.0.0/24 IP Addresses. The new server that is sitting in on Data Centre is on 172.10.10.10/24 IP Addresses. The static route has been set up on both end, and the DNS as well. I believe this is the issue. Does anyone how to overcome this situation? Thank you.

  Read the article

• Is there any way for ME to improve routing to an overseas server?

  - by Simon Hartcher

  I am trying to make a connection to a gaming server in Asia from Australia, but my ISP routes my connection through the US. Tracing route to worldoftanks-sea.com [116.51.25.54]over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.1.1 2 34 ms 42 ms 45 ms 10.20.21.123 3 40 ms 40 ms 43 ms 202.7.173.145 4 51 ms 42 ms 36 ms syd-sot-ken-crt1-ge-6-0-0.tpgi.com.au [202.7.171.121] 5 175 ms 200 ms 195 ms ge5-0-5d0.cir1.seattle7-wa.us.xo.net [216.156.100.37] 6 212 ms 228 ms 229 ms vb2002.rar3.sanjose-ca.us.xo.net [207.88.13.150] 7 205 ms 204 ms 206 ms 207.88.14.226.ptr.us.xo.net [207.88.14.226] 8 207 ms 215 ms 220 ms xe-0.equinix.snjsca04.us.bb.gin.ntt.net [206.223.116.12] 9 198 ms 201 ms 199 ms ae-7.r20.snjsca04.us.bb.gin.ntt.net [129.250.5.52] 10 396 ms 391 ms 395 ms as-6.r20.sngpsi02.sg.bb.gin.ntt.net [129.250.3.89] 11 383 ms 384 ms 383 ms ae-3.r02.sngpsi02.sg.bb.gin.ntt.net [129.250.4.178] 12 364 ms 381 ms 359 ms wotsg1-slave-54.worldoftanks.sg [116.51.25.54] Trace complete. Since I think it will be unlikely that my ISP will do anything, are there any ways to improve my routing to the server without them having to intervene? NB. The game runs predominately over UDP, so I believe most low ping services are out of the question, as they rely on TCP traffic.

  Read the article

• Weird routing issue

  - by Joel Coel

  I'm having some weird internet problems on campus. I know it's something simple, but it's a case where I need another set of eyes. I think I can explain the problem best by posting a tracert: Tracing route to google.com [74.125.45.147] over a maximum of 30 hops: 1 3 ms 3 ms 3 ms 192.168.8.1 2 1 ms 1 ms 1 ms elissaemily-pc.york.edu [192.168.10.5] 3 2 ms 2 ms 2 ms rrcs-76-79-19-33.west.biz.rr.com [76.79.19.33] 4 31 ms 3 ms 2 ms ge-1-1-0.lnclne00-mx41.neb.rr.com [76.85.220.109] 5 20 ms 17 ms 17 ms ge-7-3-0.chcgill3-rtr1.kc.rr.com [76.85.220.137] 6 20 ms 20 ms 19 ms ae-5-0.cr0.chi30.tbone.rr.com [66.109.6.112] 7 19 ms 19 ms 24 ms ae-1-0.pr0.chi10.tbone.rr.com [66.109.6.155] 8 26 ms 24 ms 24 ms 74.125.48.109 9 23 ms 24 ms 21 ms 216.239.46.246 10 39 ms 39 ms 55 ms 209.85.242.215 11 39 ms 39 ms 39 ms 209.85.254.243 12 39 ms 40 ms 96 ms 209.85.253.145 13 39 ms 39 ms 39 ms yx-in-f147.1e100.net [74.125.45.147] Trace complete. Note the second entry in there. Not only is the host name a student's computer, but the ip address doesn't exist. Dhcp shows that host as having a different address and you can't ping any 192.168.10.5. Yet somehow it's routing packets for us (and not very well, either — things are slow right now). The basic network routing table looks like this: Destination Subnet Mask Gateway --------------------------------------- Default Route -- 10.1.1.5 (our firewall) 10.0.0.0 255.0.0.0 -- 192.168.8.0 255.255.252.0 --

  Read the article

• Browsing Playstation 3 from Ubuntu Box

  - by zfranciscus

  Hi, My Goal here is to be able to transfer files from my Ubuntu 10.04 box to my PS3 over a wireless network. My PS3 and my Ubuntu Box is on the same home network. These are some stuff that I tried: I can't see my PS 3 from 'Places ? Network' nor other computer that is running on windows. I am still puzzled by this fact. I have not tried ping-ing my PS3. I'll try that later today and post the result in the forum I install PS3MediaServer (http://code.google.com/p/ps3mediaserver/). Someone in the PS3 chat forum (http://www.ps3chat.com/playstation-3...lp-please.html) claims that it will enable your ubuntu box to browse PS3. So I downloaded PS3MediaServer, and ran the software. The status tab keep showing "Waiting ...". It seems that PS3MediaServer can't find my PS3. Some how I feel that 1 and 2 are related somehow.Perhaps that there is something wrong with my Ubuntu network settings that is preventing my ubuntu box from looking up other device on the network. I can go to the Internet fine, but I can't see other device on my network. Does anyone have any experience in this area. I would like to hear your experience and perhaps some solution. Any kind of hints or help will be greatly appreciated. Cheers

  Read the article

• Compaq R4000 laptop randomly locking up

  - by Josh

  I have a Compaq R4000 laptop with 2GB of RAM, running Ubuntu Linux 9.10. It is randomly locking up on me, approximately once every two days. I have a second partition with Windows XP Home installed, and I have had the system lock up in XP as well, meaning I believe this is a hardware issue. I have run two passes of Memtest86+ with no errors. The system has a fan that has died, so I initially suspected overheating. However the system just locked up on me while I was in the middle of typing a script to warn me / shut down if the temperature was too high. When the lockup happened the temperature was 88°F, so I am now starting to believe that may not be the issue. When the system locks up, I cannot SSH in nor ping it. Nothing shows in syslog when I reboot. I have configured it to send syslog messages to a local server as well and no messages appear on that server when the lockup happens. I am open to any and all advice!

  Read the article

• VLAN with trunk to avoid broadcast storm in a network with redundant paths

  - by liv2hak

  I have 6 Juniper switches (EX - 2200) connected to each other as shown in the network topology. I have two PC's that I am using PC1 - (used for configuring the 6 switches via minicom) PC2 - to monitor the traffic between the switches via the Ports that are marked with arrows in the diagram. STEP 1: I create a new vlan On Switch 3 (SW3) that includes Port 12 and Port 22. I also assign l3-interface to the vlan (vlan_2) with ip address - 192.168.1.7. Now I plug-in Port 0 of Switch 3 on PC2. Now I try pinging 192.168.1.7 from PC2 (192.168.1.10) I want to know what will happen? My postulation is that I will not be able to ping SW3 from PC2.This is because SW3 (Port 12 and Port 22) is a part of a vlan_2 and vlan_2 logically breaks up broadcast domains and so 192.168.1.7 will not be reachable from 192.168.1.10. Now I have an l3-interface on SW1 with IP 192.168.1.1 using default vlan( vlan-id 0). Similarly I have enabled IP on SW2 - 192.168.1.2 SW3 - 192.168.1.3 SW4 - 192.168.1.4 SW5 - 192.168.1.5 SW6 - 192.168.1.6 all using default vlan. I create VLAN2 with the following configuration SW3 - Port 12,Port 22. SW6 - Port 14 I create VLAN3 with the following configuration SW3 - Port 0 SW6 - Port 0 I also configure a VLAN trunk between SW3 and SW6 using the following commands. edit interfaces ge-0/0/12 set unit 0 family ethernet-switching port-mode trunk edit interfaces ge-0/0/12 set unit 0 family ethernet-switching vlan members all There is a redundant path in the network as the loop between SW3 and SW6 is closed.There is no broadcast storm in the network? What is the reason for this? I have not enabled STP or RSTP.still there is no broadcast storm.what is the reason for this. (Please ignore the CISCO symbol on the switches in the diagram.All swithes are Junper EX 22-00.)

  Read the article

• jboss 5.1 mysql connection pooling

  - by boyd4715

  I am using JBOSS 5.1.0.GA, MySQL 5.5 and Hibernate 3.3.1 GA (included with JBOSS) + Spring. My question is do I need to add c3p0 as a data source in my spring/hibernate configuration for connection pooling or are the setting in the JBOSS mysql-ds.xml setting enough. My mysql-ds.xml is the following: <datasources> <local-tx-datasource> <jndi-name>MySqlDS</jndi-name> <connection-url>jdbc:mysql://localhost:3306/ecotrak</connection-url> <driver-class>com.mysql.jdbc.Driver</driver-class> <user-name>ecotrak</user-name> <password>ecotrak</password> <min-pool-size>5</min-pool-size> <max-pool-size>20</max-pool-size> <idle-timeout-minutes>5</idle-timeout-minutes> <exception-sorter-class-name>org.jboss.resource.adapter.jdbc.vendor.MySQLExceptionSorter</exception-sorter-class-name> <!-- should only be used on drivers after 3.22.1 with "ping" support --> <valid-connection-checker-class-name>org.jboss.resource.adapter.jdbc.vendor.MySQLValidConnectionChecker</valid-connection-checker-class-name> <!-- sql to call when connection is created <new-connection-sql>some arbitrary sql</new-connection-sql> --> <!-- sql to call on an existing pooled connection when it is obtained from pool - MySQLValidConnectionChecker is preferred for newer drivers <check-valid-connection-sql>some arbitrary sql</check-valid-connection-sql> --> <!-- corresponding type-mapping in the standardjbosscmp-jdbc.xml (optional) --> <metadata> <type-mapping>mySQL</type-mapping> </metadata> </local-tx-datasource> </datasources>

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• Server 2003 crashing intermittently, want to transfer function to other DC

  - by user1305332

  I have a Win2003R2 server that is intermittently crashing after some virus were introduced. I'm sure all virus have been cleaned thanks to Malwarebytes (were using McAfee - useless). When it crashes you can't login (local or remote) but can still access files remotely and ping it. After a while even file sharing stops and have to kill power to restart it (no BSOD) I need to either fix it (tried to reinstall SP2 and I tried to reinstall windows in repair mode but the repair option was not available when I booted from installation disks) or move it's functionality to another DC (another 2003R2 server). The server that's crashing is old with SCSI drives while the new server uses SATA drives and faster so it seems like a good idea to just transfer roles and ditch the old box. Finding replacement SCSI drives looks expensive if they ever fail. What would I need to transfer roles. If I just move the 5 FSMO roles and copy over the file shares. Would the new server have enough to run without the old server? Never done something like this, just want some tips. Thanks.

  Read the article

• Why is uploading to S3 so slow?

  - by Tom Marthenal

  I am using s3cmd to upload to S3: # s3cmd put 1gb.bin s3://my-bucket/1gb.bin 1gb.bin -> s3://my-bucket/1gb.bin [1 of 1] 366706688 of 1073741824 34% in 371s 963.22 kB/s I am uploading from Linode, which has an outgoing bandwidth cap of 50 Mb/s according to support (roughly 6 MB/s). Why am I getting such slow upload speeds to S3, and how can I improve them? Update: Uploading the same file via SCP to an m1.medium EC2 instance (SCP from my Linode to the instance's EBS drive) gives about 44 Mb/s according to iftop (any compression done by the cipher is not a factor). Traceroute: Here's a traceroute to the server it's uploading to (according to tcpdump). # traceroute s3-1-w.amazonaws.com. traceroute to s3-1-w.amazonaws.com. (72.21.194.32), 30 hops max, 60 byte packets 1 207.99.1.13 (207.99.1.13) 0.635 ms 0.743 ms 0.723 ms 2 207.99.53.41 (207.99.53.41) 0.683 ms 0.865 ms 0.915 ms 3 vlan801.tbr1.mmu.nac.net (209.123.10.9) 0.397 ms 0.541 ms 0.527 ms 4 0.e1-1.tbr1.tl9.nac.net (209.123.10.102) 1.400 ms 1.481 ms 1.508 ms 5 0.gi-0-0-0.pr1.tl9.nac.net (209.123.11.62) 1.602 ms 1.677 ms 1.699 ms 6 equinix02-iad2.amazon.com (206.223.115.35) 9.393 ms 8.925 ms 8.900 ms 7 72.21.220.41 (72.21.220.41) 32.610 ms 9.812 ms 9.789 ms 8 72.21.222.141 (72.21.222.141) 9.519 ms 9.439 ms 9.443 ms 9 72.21.218.3 (72.21.218.3) 10.245 ms 10.202 ms 10.154 ms 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * The latency looks reasonable, at least until the server stopped responding to ping requests.

  Read the article

• DD-WRT router causing IP address conflicts across network

  - by r.tanner.f

  My DD-WRT router has lost its mind! I just set up two DD-WRT routers, one as a WAP (working fine) and one in Client Bridge (routed) mode (the problem). Not long after setup I started seeing IP address conflicts on other machines. The event log always points the finger at my Client Bridge router's MAC address. Neighbour table overflow The log on my router is flooded with Neighbour table overflow errors. These start a minute or two after boot. The network is rather large, with +200 IP addresses being used in this subnet. The other router shows no such errors. Mass ARP requests from 1.1.1.1 I'm also seeing constant ARP requests (with the problem router's MAC address) from 1.1.1.1. Seems like it's bugging everything on the network for its MAC address and then promptly forgetting it (or never receiving a response). Configuration: Model: Buffalo N600 Firmware: DD-WRT v24SP2-MULTI (03/21/11) Wireless Mode: Client Bridge (routed) I'm not sure what configuration details are relevant and I'd rather not have comments flooded, so just ping me in this chat if you want to know something. Why is my router stealing IP addresses and how can I stop it?

  Read the article

< Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >