Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 82/343 | < Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• Wifi is connected but internet not working?

  - by Philip

  I have a lenovo x230 running ubuntu 12.04lts. I've been using it just fine for a while, but all of a sudden the internet's stopped working. It's connected to the router just fine (I can see the antenna bars saying it's connected) but when I try to go to a webpage, it's just loading forever. I've tried the fix listed here (http://ubuntuforums.org/showthread.php?t=1985079) but it hasn't done anything (the instructions are a little confusing though). I'm booting windows 7 right now and the internet works just fine when I'm on windows, so I know it must be a problem with ubuntu. I haven't touched any network settings before this problem happened, and I've been using it just fine for months, so I don't know why I'm getting this problem all of a sudden. Oh and I haven't updated anything in a few weeks (you know when the update manager pops up every so often listing all the things there's an update for) so I know it's not some update that broke it.

  Read the article

• No keyring secrets found for [ssid] /802-11-wireless-security, ubuntu 12.04

  - by acimer

  I'm on Ubuntu 12.04 x64bit, installed it couple of days ago. The issue i'm having is this: on startup it connects to my wireless without a problem, but after a while I am disconnected and prompted to enter the key for the wireless network (which is entered - saved) so i just click 'ok', but wireless doesn't connect again. Reseting network manager doesn't help either. Only restart, after which, ubuntu connects to the said wireless without a problem. Terminal outputs this error message: ** Message: No keyring secrets found for cimermanovic /802-11-wireless-security; asking user. cimermanovic is the ssid name. also, here are some error messages that network manager is giving: (nm-applet:31926): GdkPixbuf-CRITICAL **: gdk_pixbuf_scale_simple: assertion `dest_width 0' failed (nm-applet:31693): GdkPixbuf-CRITICAL **: gdk_pixbuf_scale_simple: assertion `dest_width 0' failed (nm-applet:30184): GdkPixbuf-CRITICAL **: gdk_pixbuf_scale_simple: assertion `dest_width 0' failed What should i do to fix this? Thanks!

  Read the article

• Seeking advice on tools and technology for my new game [closed]

  - by k.k. slider

  I'm a C# developer who has been programming a game in my spare time using XNA and Visual Studio. The game's logic is mostly done and I've completed a prototype that has most of the functionality of (what I envision to be) the final game. However, having heard about the uncertain future and (possibly) limited audience for XNA games, I'm looking to switch platforms... but I don't know what technology would best suit my needs. Below are some specifics about my game and what exactly I'm looking for, if you're interested: The game is a 2D turn-based tactical RPG (strategy game) for two players. It is a basic sprite and tile based game with animations and sound. 3D capabilities are not necessary. I'd like to allow players to compete with others online, and have a basic ranking/matchmaking system. I will probably need something that can interact with a server and a database (the game is turn-based and has no RNG, so cheating would be easy to detect even if most computation is done client-side and minimal data is sent to the server). Ideally, I would be able to release an early version of the game and have people give feedback as I develop additional features (similar to Minecraft). I'd prefer to have a way to release periodic updates to the game instead of releasing an absolute final product. To reach the widest possible audience, I'd prefer technology that allows me to release on PC, Android, iOS, and (maybe) Mac. This is a game with simple mouse inputs which can fit on a mobile touch screen. The game should be monetizable. If I find success with this game, then I may consider becoming a full-time indie game developer. I have several other game ideas and have learned quite a bit from my first attempt at game development. My first thought was an F2P/microtransaction model, but I'm open to other suggestions. Language isn't a primary concern of mine, since I have a decent amount of experience using several languages to program large projects. I'm willing to spend money (e.g. on a developer's license), but the more expensive it gets, the more hesitant I am to use it. I've looked into the following solutions... there are a LOT of tools out there... if anyone has experience with any of these and would like to recommend/reject any of them, it would be helpful. C#/.NET (XNA/MonoGame/SDL/SlimDX/Xamarin/ExEn/ANX?) HTML5/JS (AppMobi/PhoneGap/Marmalade/FlashCanvas/Cordova/libRocket?) Python (Pyglet/Pygame/Kivy?) Java (JavaFX/libGDX?) Unity/Construct 2/Cocos2D/NME/Corona/other game creation software? I'd like something that can do 2D and isn't limited by being too high-level. Other languages (Lua/LOVE? Moai?) Thanks for answering this rather long and tedious question...

  Read the article

• How to change the IP address on my Ubuntu virtual NIC

  - by DextrousDave

  I have a physical windows system, on which I run Vmware Workstation. Now on VMware I run Ubuntu 12.10. I am running a webserver on Ubuntu via LAMP, inside VMware. Problem: Now my local IP address for my virtual NIC (the one Ubuntu is using) has an address of 192.168.159.7, and my home router only issues IP addresses of the range 10.0.0.x. So if I want to port forward to the virtual NIC, which has a 192.168 address, I cannot, so my LAMP webserver cannot be accessed externally since the router does not know to send the packets on port 80 to the virtual NIC... How do I fix that? The only way I guess is to assign a 10.0.0.x ip address to the virtual NIC?? But how do I do that? I tried to do it on the host Windows machine with 'Get my IP address automatically' but it issues a 192.168 address every time... Thank you

  Read the article

• Network connection fails when downloading data

  - by Guus

  In the past few weeks, I've noticed my network connection becoming unstable while downloading files. I'm not sure how to diagnose this issue. I've found that my network connections appear to be temporarily unresponsive (for periods up to a minute or so) while I'm downloading a file (that's large enough to not be downloaded instantly). The problem occurs when downloading data through a webbrowser, but also when using SCP to download data from a remote location. During the period in which network connections are unresponsive, every resource that I try to access over the network is unavailable. This includes: The download itself (SCP reports a 'stalled' download) Web pages (won't load - browsers report 'resource unavailable') SSH sessions (CLI freezes) VPN connections (connections terminate) IM client connections (client starts reconnection attempts) ... (everything is pretty much dead) I've noticed that during such a period, I cannot even access the (web-based) administrative console of the router on my LAN at home (although it remains reachable for other devices). The problem occurs when connected to my home network, but also when I'm in the office. Other devices than my laptop are not affected. Given the above two characteristics I assume the problem cause lies within my laptop, not the network infrastructure. I'm running Ubuntu 11.10. Apart from applying automatic updates from Ubuntu, I can't think of a change that I applied to the OS that could have started the problems. I'm absolutely positive that this issue did not occur up to a few weeks ago (as it's very noticeable, and only started to annoy me in the last few days). When the problem occurs, applications that make use of a network connection fail visibly (I get popups telling me that a VPN connection is broken, for instance). The network manager does not report any issues related to my wifi-connection though. Help?

  Read the article

• Set up Trendnet TEW-638APB Access point on Ubuntu 14.04

  - by Mr. Smileys

  I have a computer running Ubuntu 14.04, it has 2 Ethernet ports. I would like to set up this computer so that the internet comes in on one of the ports and is then shared through the other port with the Trendnet wireless access point that my other devices would connect to and use the internet. I have looked online for information on setting this up but have not been able to find anything. If someone could point me to a guide that would help me or just tell me how to do this in an answer I would really appreciate it. please help me to solve this problem

  Read the article

• Lag compensation of projectile shooting game

  - by Denis Ermolin

  I'm thinking about an algorithm for firing projectiles with lag compensation. Now I did find only one descent solution: Player hits fire button. Client sends input "fire". Client waits for server response. Server generates bullet then sends response to client. Client recieves response and finally fires projectile. Is this solution only "trueway"? I find it the only one that can be fair to all of the clients. Valve in this case, doesn't compensate lag from rocket shots. I am feeling that I will not compensate it, too. I think that with today's bandwidth I can close my eyes on this problem, because I don't see any solutions with fair logic. What do you think?

  Read the article

• Strange Flash AS3 xml Socket behavior

  - by Rnd_d

  I have a problem which I can't understand. To understand it I wrote a socket client on AS3 and a server on python/twisted, you can see the code of both applications below. Let's launch two clients at the same time, arrange them so that you can see both windows and press connection button in both windows. Then press and hold any button. What I'm expecting: Client with pressed button sends a message "some data" to the server, then the server sends this message to all the clients(including the original sender) . Then each client moves right the button 'connectButton' and prints a message to the log with time in the following format: "min:secs:milliseconds". What is going wrong: The motion is smooth in the client that sends the message, but in all other clients the motion is jerky. This happens because messages to those clients arrive later than to the original sending client. And if we have three clients (let's name them A,B,C) and we send a message from A, the sending time log of B and C will be the same. Why other clients recieve this messages later than the original sender? By the way, on ubuntu 10.04/chrome all the motion is smooth. Two clients are launched in separated chromes. windows screenshot Can't post linux screenshot, need more than 10 reputation to post more hyperlinks. Listing of log, four clients simultaneously: [16:29:33.280858] 62.140.224.1 >> some data [16:29:33.280912] 87.249.9.98 << some data [16:29:33.280970] 87.249.9.98 << some data [16:29:33.281025] 87.249.9.98 << some data [16:29:33.281079] 62.140.224.1 << some data [16:29:33.323267] 62.140.224.1 >> some data [16:29:33.323326] 87.249.9.98 << some data [16:29:33.323386] 87.249.9.98 << some data [16:29:33.323440] 87.249.9.98 << some data [16:29:33.323493] 62.140.224.1 << some data [16:29:34.123435] 62.140.224.1 >> some data [16:29:34.123525] 87.249.9.98 << some data [16:29:34.123593] 87.249.9.98 << some data [16:29:34.123648] 87.249.9.98 << some data [16:29:34.123702] 62.140.224.1 << some data AS3 client code package { import adobe.utils.CustomActions; import flash.display.Sprite; import flash.events.DataEvent; import flash.events.Event; import flash.events.IOErrorEvent; import flash.events.KeyboardEvent; import flash.events.MouseEvent; import flash.events.SecurityErrorEvent; import flash.net.XMLSocket; import flash.system.Security; import flash.text.TextField; public class Main extends Sprite { private var socket :XMLSocket; private var textField :TextField = new TextField; private var connectButton :TextField = new TextField; public function Main():void { if (stage) init(); else addEventListener(Event.ADDED_TO_STAGE, init); } private function init(event:Event = null):void { socket = new XMLSocket(); socket.addEventListener(Event.CONNECT, connectHandler); socket.addEventListener(DataEvent.DATA, dataHandler); stage.addEventListener(KeyboardEvent.KEY_DOWN, keyDownHandler); addChild(textField); textField.y = 50; textField.width = 780; textField.height = 500; textField.border = true; connectButton.selectable = false; connectButton.border = true; connectButton.addEventListener(MouseEvent.MOUSE_DOWN, connectMouseDownHandler); connectButton.width = 105; connectButton.height = 20; connectButton.text = "click here to connect"; addChild(connectButton); } private function connectHandler(event:Event):void { textField.appendText("Connect\n"); textField.appendText("Press and hold any key\n"); } private function dataHandler(event:DataEvent):void { var now:Date = new Date(); textField.appendText(event.data + " time = " + now.getMinutes() + ":" + now.getSeconds() + ":" + now.getMilliseconds() + "\n"); connectButton.x += 2; } private function keyDownHandler(event:KeyboardEvent):void { socket.send("some data"); } private function connectMouseDownHandler(event:MouseEvent):void { var connectAddress:String = "ep1c.org"; var connectPort:Number = 13250; Security.loadPolicyFile("xmlsocket://" + connectAddress + ":" + String(connectPort)); socket.connect(connectAddress, connectPort); } } } Python server code from twisted.internet import reactor from twisted.internet.protocol import ServerFactory from twisted.protocols.basic import LineOnlyReceiver import datetime class EchoProtocol(LineOnlyReceiver): ##### name = "" id = 0 delimiter = chr(0) ##### def getName(self): return self.transport.getPeer().host def connectionMade(self): self.id = self.factory.getNextId() print "New connection from %s - id:%s" % (self.getName(), self.id) self.factory.clientProtocols[self.id] = self def connectionLost(self, reason): print "Lost connection from "+ self.getName() del self.factory.clientProtocols[self.id] self.factory.sendMessageToAllClients(self.getName() + " has disconnected.") def lineReceived(self, line): print "[%s] %s >> %s" % (datetime.datetime.now().time(), self, line) if line=="<policy-file-request/>": data = """<?xml version="1.0"?> <!DOCTYPE cross-domain-policy SYSTEM "http://www.adobe.com/xml/dtds/cross-domain-policy.dtd"> <!-- Policy file for xmlsocket://ep1c.org --> <cross-domain-policy> <allow-access-from domain="*" to-ports="%s" /> </cross-domain-policy>""" % PORT self.send(data) else: self.factory.sendMessageToAllClients( line ) def send(self, line): print "[%s] %s << %s" % (datetime.datetime.now().time(), self, line) if line: self.transport.write( str(line) + chr(0)) else: print "Nothing to send" def __str__(self): return self.getName() class ChatProtocolFactory(ServerFactory): protocol = EchoProtocol def __init__(self): self.clientProtocols = {} self.nextId = 0 def getNextId(self): id = self.nextId self.nextId += 1 return id def sendMessageToAllClients(self, msg): for client in self.clientProtocols: self.clientProtocols[client].send(msg) def sendMessageToClient(self, id, msg): self.clientProtocols[id].send(msg) PORT = 13250 print "Starting Server" factory = ChatProtocolFactory() reactor.listenTCP(PORT, factory) reactor.run()

  Read the article

• How to merge multiple internet connections into one

  - by Luis Alvarado

  My PC has 2 wired cards. Both gigalan. It also has 2 wireless cards. One broadcom with proprietary drivers and ralink with open software (which works much better than broadcom). My cellphone can share its connection wirelessly to my PC. But I also have a wired connection. So I have multiple connections that I can use to have internet. How can I merge 2 or more connections together and balance them to enjoy one unified internet experience that it is the sum of all internet connections connected to it. For example if I have an internet connection that offers 1024KB/Sec and another that offers 512KB/Sec and one small one that offers 128KB/Sec, after load balancing and merging all connections, I could download at a speed of 1664KB/Sec using all 3 internet connections as one for example. This question has always intrigued me.

  Read the article

• Hotspot is getting disconnected from other windows system?

  - by Gaurav_Java

  I created Hotspot for sharing my system internet for other system . but after 5 - 10 min my system internet is not able to share internet but it is connected with other windows system .windows showing (No internet access ) But after running this sudo killall dnsmasq windows is able to use internet connection not happening with one system same thing is happening with 2 -3 windows system . In many cases i have 2 restart my system Here My Hotspot setting

  Read the article

• System wide Proxy settings when on a windows network with a password

  - by sav

  I'm using Ubuntu on a windows network. I want to connect to the world wide web. I have followed the steps here which I have found very useful. However when I try to ping a website (eg: ping www.wikipedia.org) I get no reply. I can ping local computers on my network, but I need to go through our proxy to get to the world wide web. I can even browse wikipedia using firefox, I just needed to enter the proxy configuration script location and my username and password. I'm quite sure the reason I'm having this trouble is because I havn't entered a username and password. I'm not sure how to do this on a system wide level. ultimately I would like to be able to use package managers like synaptic but first I need them to be able to connect to the internet. EDIT As sugested I created a /etc/apt/apt.conf file like Acquire::http::Proxy "http://chrisav:[email protected]:8080"; Acquire::https::Proxy "https://chrisav:[email protected]:8080"; Acquire::ftp::Proxy "ftp://chrisav:[email protected]:8080"; Acquire::socks::Proxy "socks://chrisav:[email protected]:8080"; However I still cant ping wikipedia when I try installing stuff I get chris@chris-Ubuntu:~$ sudo apt-get install kate Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package kate

  Read the article

• Intermittent internet connectivity

  - by Rob Oplawar

  UPDATED: I recently built a new computer and set it up to dual-boot Windows 7 and Ubuntu 11.10. In Windows, using the same hardware, my LAN connectivity is solid. In Ubuntu, however, my network interface periodically dies and resets itself; I'll have a solid connection for 30 seconds, and then it will go out for 30 seconds. When I tail the log: tail -f /var/log/kern.log I see "eth0 link up" messages appear periodically, corresponding with the return of connectivity. I posted the original question months ago, and misinterpreted what was going on. With a working Internet connection in Windows, I ignored the problem for some months. See my answer below for the solution (drivers). ORIGINAL POST In Ubuntu, although I maintain a solid connection to my LAN (pinging the router IP address consistently returns a good result), my internet connectivity drops in and out. When I continuously ping 74.125.227.18 (a google.com server), I get responses for a while, then I start getting "Destination Host Unreachable" for a while, then I get responses again. This happens consistently, dropping the connection for about 30 seconds out of every minute or two. Whether I configure my network via the network manager or via /etc/network/interfaces seems to make no difference. I configure with the following settings: address 192.168.1.101 network 192.168.1.0 gateway 192.168.1.99 (my router's IP address) netmask 255.255.255.0 (confirmed as the right netmask for the router) broadcast 192.168.1.255 (also confirmed with the router). ifconfig confirms that these settings are working: eth0 Link encap:Ethernet HWaddr 50:e5:49:40:da:a6 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe40:daa6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11557 errors:0 dropped:11557 overruns:0 frame:11557 TX packets:13117 errors:0 dropped:211 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9551488 (9.5 MB) TX bytes:1930952 (1.9 MB) Interrupt:41 Base address:0xa000 I get the same issue when I use automatic DHCP address settings, although I did confirm that there is no other machine on the network with the static IP address I want to use. As I said, the connection to the local network stays solid - I never have any trouble pinging 192.168.1.* - it's internet addresses that I intermittently cannot reach. It's not a DNS issue because pinging known IP addresses directly shows the same behavior. Also, I don't think it's a hardware issue, as I never have any internet connectivity problems on the same machine in Windows. The network hardware is built into the motherboard: Gigabyte Z68XP-UD3P. I managed to bring the OS fully up to date, according to the update manager, but it didn't fix the issue, and with my limited understanding of network architecture I'm at my wit's end. The only clue I can see is that ifconfig is reporting a lot of dropped packets, but I'm not sure what to do about it. UPDATE: It seems my problem is a little more generic than I described; now when I try pinging my router and google simultaneously, they both go unreachable at the same time. Running ifdown eth0 and then ifup eth0 brings it back temporarily; if I just wait it comes back after a couple of minutes. I'll broaden my search through intermittent network connectivity problems.

  Read the article

• Is there a simple isometric graphical game engine (using vectors?) that could be used for a (multiplayer) crafting/farming game? [closed]

  - by Renier Wijnen

  Possible Duplicate: Good, free isometric game engine? With little game development experience (albeit having graphical skills and some programming knowledge) a group currently working on a game used to explain permaculture through interaction would like to create a simple concept game. Is there a specific engine or set of tools we could used to achieve this? Being able to make it an (online) multiplayer game would be much preferred. Thank you in advance for your input.

  Read the article

• wired connection not being recognised in ubuntu 10.04 lts

  - by arun

  I have windows7 installed on my C drive and ubuntu 10.04 lts on my D drive. When I plud the lan cable (ethernet cable) onto the ethernet card of my laptop, windows7 identifies the network correctly without the need for any manual settings and connects me to the network correctly. Unfortunately, in ubuntu, even after plugging in the cable, nothing happens (on the network side). It is only scanning for wireless networks it seems, and doesnt bother about the wired networks. I tried adding a new wired connection and manually entered the physical address which was displayed when i connected to the network using windows. i entered the phy address, and told it to use auto dhcp and saved the dialog bog in ubuntu network connection. Still there is no change, and ubuntu doesnt seem to recognise anything. please let me know how to work with wired connections using ubuntu, and why my wired cable is not being recognized in ubuntu. thanks. PS: I am pretty new to ubuntu/ linux :)

  Read the article

• How can I work out how many IP addresses there are in a given range?

  - by Jarede

  I'm wondering if there is a formula to work out the amount of IP addresses in a given range. I have a system that takes either a single IP address or a start and and end IP address: A single one might be: 145.16.23.241 A range might be: 145.16.23.122 - 145.16.23.144 The people inputting these aren't technical, nor are they receiving these details from technical people, so suggesting using CIDR notation isn't an answer for me. I want to be able to highlight that when entering a range such as: 122.100.10.12 - 128.10.200.140 it might not actually be a range and rather 2 singular IP addresses since such a range would comprise of x (large number of) IP addresses. Is there a basic formula to help me highlight this?

  Read the article

• Multiplayer tile based movement synchronization

  - by Mars

  I have to synchronize the movement of multiple players over the Internet, and I'm trying to figure out the safest way to do that. The game is tile based, you can only move in 4 directions, and every move moves the sprite 32px (over time of course). Now, if I would simply send this move action to the server, which would broadcast it to all players, while the walk key is kept being pressed down, to keep walking, I have to take this next command, send it to the server, and to all clients, in time, or the movement won't be smooth anymore. I saw this in other games, and it can get ugly pretty quick, even without lag. So I'm wondering if this is even a viable option. This seems like a very good method for single player though, since it's easy, straight forward (, just take the next movement action in time and add it to a list), and you can easily add mouse movement (clicking on some tile), to add a path to a queue, that's walked along. The other thing that came to my mind was sending the information that someone started moving in some direction, and again once he stopped or changed the direction, together with the position, so that the sprite will appear at the correct position, or rather so that the position can be fixed if it's wrong. This should (hopefully) only make problems if someone really is lagging, in which case it's to be expected. For this to work out I'd need some kind of queue though, where incoming direction changes and stuff are saved, so the sprite knows where to go, after the current movement to the next tile is finished. This could actually work, but kinda sounds overcomplicated. Although it might be the only way to do this, without risk of stuttering. If a stop or direction change is received on the client side it's saved in a queue and the char keeps moving to the specified coordinates, before stopping or changing direction. If the new command comes in too late there'll be stuttering as well of course... I'm having a hard time deciding for a method, and I couldn't really find any examples for this yet. My main problem is keeping the tile movement smooth, which is why other topics regarding synchronization of pixel based movement aren't helping too much. What is the "standard" way to do this?

  Read the article

• Strategy to prevent players from seeing through walls in an online FPS?

  - by geneotech

  Why do we still moan on wallhackers in multiplayer first-person shooters ? Isn't it possible to perform occlusion culling for all players server-side ? For example, send player xyz information to client only when the player is visible in client's frustum and not occluded by any object ? Even if the collision-geometry is very simplified, most of the time cheater won't receive tactical information. Why not do this ?

  Read the article

• How to perform game object smoothing in multiplayer games

  - by spaceOwl

  We're developing an infrastructure to support multiplayer games for our game engine. In simple terms, each client (player) engine sends some pieces of data regarding the relevant game objects at a given time interval. On the receiving end, we step the incoming data to current time (to compensate for latency), followed by a smoothing step (which is the subject of this question). I was wondering how smoothing should be performed ? Currently the algorithm is similar to this: Receive incoming state for an object (position, velocity, acceleration, rotation, custom data like visual properties, etc). Calculate a diff between local object position and the position we have after previous prediction steps. If diff doesn't exceed some threshold value, start a smoothing step: Mark the object's CURRENT POSITION and the TARGET POSITION. Linear interpolate between these values for 0.3 seconds. I wonder if this scheme is any good, or if there is any other common implementation or algorithm that should be used? (For example - should i only smooth out the position? or other values, such as speed, etc) any help will be appreciated.

  Read the article

• A simple example of movement prediction

  - by Daniel

  I've seen lots of examples of theory about the reason for client-side prediction, but I'm having a hard time converting it into code. I was wondering if someone knows of some specific examples that share some of the code, or can share their knowledge to shed some light into my situation. I'm trying to run some tests to get a the movement going (smoothly) between multiple clients. I'm using mouse input to initiate movement. I'm using AS3 and C# on a local Player.IO server. Right now I'm trying to get the Client side working, as I'm only forwarding position info with the client. I have 2 timers, one is an onEnterFrame and the other is a 100ms Timer, and one on mouseClick listener. When I click anywhere with a mouse, I update my player class to give it a destination point On every enterFrame Event for the player, it moves towards the destination point At every 100ms it sends a message to the server with the position of where it should be in a 100ms. The distance traveled is calculated by taking the distance (in Pixels) that the player can travel in one second, and dividing it by the framerate for the onEnterFrame handler, and by the update frequency (1/0.100s) for the server update. For the other Players, the location is interpolated and animated on every frame based on the new location. Is this the right way of doing it?

  Read the article

• System freeze after opening Wi-Fi menu can boot into the machine and use Internet in recovery mode

  - by Michael

  So right now sitting in front of my Alienware area 51 desktop. It has a Broadcom Netlink BCM 5784M gigabit ethernet PCI E card. Most of the time able to get through the login screen and to the main screen if I click on the wireless settings on the top right-hand corner the system immediately freezes the cursor does not move at all keyboards are unresponsive. I was doing some quick Google searching and I found a suggestion to boot into recovery mode I did this and did a apt-get Distribution update which ran successfully installed then I rebooted into the regular system same thing I'm pretty sure it's the network card because even if I don't click the settings if a network related dialog opens such as disconnection or connection the system again immediately freezes. I'm running Ubuntu 13.04 ** update 1 ** Just was able to use my system for a little bit however when I went into Firefox and hit the web it again froze so obviously a driver problem but I'm not sure how to get drivers for Broadcom which apparently according to the description on stack-overflow is terrible Any ideas? Sorry for lack of punctuation on an ipad.

  Read the article

• SS7(M3UA, SCCP, TCAP, MAP) Stack

  - by Ammar Hameed

  I'm building an open source SMSC from scratch; it's almost finished, The SRI and the forwardSM operations are working, but I still have few things to do for the receiving part. I've built the SS7 stack already, but I'm using DB for saving the TCAP transactions IDs to be updated later to get/generate responses. My approach is this: I created memory table (heap table), saved the TCAP TID in the database, then compared the received TCAP TID with the TIDs saved in the database and then decide whether to end the TCAP session or continue. What is the best way to implement it? I'm thinking of doubly linked list that holds the TCAP TID. Am I going towards the right direction, or should I use another technique other than database or D-linked list? Should I leave it as it is, and let the database do the job for saving the TIDs? Please note that I'm using SCTP implementation available on Linux (lsctp) as a transport protocol, the language I'm using is C and the DB is MYSQL.

  Read the article

• WINDOWS 7 DEAD BLUE SCREEN DOES NOT REBOOT OR INSTALL NEW WIN OS

  - by ADAM

  Windows died. So, I installed ubuntu, and have had difficulties downloading apps from the internet like skype or realplayer... etc. And It does not recognize my password. I needed to install drivers for my wireless from cd-rom. It does not show where to save new downloaded files and programs, and app and does not show how to install like windows does. So I would like to go back to windows. Window does not not start up anymore and I can not get safe mode with F8. It goes to black screen only and none of other parameters work when press f8! Any help is highly valued.

  Read the article

• Network connection on an Acer Aspire 5253?

  - by fuquam

  Brand new to Ubuntu and PCs for that matter. I've been a Mac user all my life but wanted to try Ubuntu on the cheap so I bought an Acer laptop 5253-BZ893. I got Ubuntu 10.10 installed with no problem. The only problem I have is I have no network connection options, wired or wireless. I just get "No Network Devices Available". The computer came with Windows 7 installed and I'm able to connect to my wireless network fine using Windows so I know the computer works. I've been searching forums and google for hours trying to figure out why I can't get a network connection using Ubuntu but so far no luck. Any suggestions? Thanks in advance.

  Read the article

• keep getting added to hosts.deny + iptables

  - by Sc0rian

  I am confused to why this has started to happen. On my local network, if I click 10-20 apache/http links my server will decide to add me hosts.deny file and block me on iptables. Its not just apache, it seems to happen with any kinda of traffic, that comes in on a flood method. Like I use subsonic, if I change tracks 10-20 times, it will do it. I would assume I have some sort of firewall which is sitting on the server which is doing this. However I do not have fail2ban or any denyhosts in /var/lib. I cannot work out why I keep getting added to hosts.deny/iptables. Thanks

  Read the article

< Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >