Search Results

Search found 47655 results on 1907 pages for 'system restore'.

Page 825/1907 | < Previous Page | 821 822 823 824 825 826 827 828 829 830 831 832  | Next Page >

• Graphics Artifacts/ Texture Flickering

  - by Cerin

  Hey I been having some problems with artifacts in games. Sometimes textures flicker. Artifacts of various shapes and sizes show up usually after a couple games of dota 2. I built my computer almost exactly one month ago and it has been doing this pretty much from the start except before the artifacts I believe just flashed on screen fast enough to where I couldn't tell what it was but I still noticed. In dota I've seen green triangular artifacts among other things. I've tried running Furmark for a while but even though it pushes the gpu much harder than dota 2, there are still no artifacts. It maxes in furmark at about 60C and running every game I've tried on it at 40C. CPU and system temp don't usually get higher than 40C either. These are my system specs: Gigabyte Z68 Intel Motherboard 16 GB Gskill Ripjaws SDRAM DDR3 Sapphire Radeon HD 7770 GHz edition Intel Core i5-2500k (with built in gpu) Corsair 750 Watt PSU windows 7-64 bit I have the latest drivers for everything. What should I do about this? Try to RMA my graphics card? Are there other things that could be causing this?

  Read the article

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

• Attaching 3.5" desktop drive to MacBook SATA

  - by Kyle Cronin

  I have a mid-2007 MacBook that, according to the Apple Store, has suffered some liquid damage and requires a new logic board to operate correctly, a ~$750 repair I've been told (would normally be around ~$300 were it not for the "liquid damage"). The unit itself works fine - the only problem I've been having is that the system does not recognize the battery and will not charge it. Curiously, the system can still be powered by the battery and even recognizes when the power cord is detached by diming the backlight, but I digress. Now that this laptop will likely become a desktop, I'm wondering if it might be possible to attach a desktop drive. I recently purchased a 2TB SATA drive and I'm wondering if it's possible to somehow attach it where the current internal drive connects. Obviously the drive itself will not fit inside the device, but as the unit will spend the rest of its days on my desk, that's not really much of an issue. My main questions are: Is this possible? If so, how would I connect the drive? Would a SATA extender cable work? Is the SATA port on my MacBook capable of powering a desktop drive? Or should I just get a SATA male-to-female cable and see if I can power the drive through other means (a cheap power supply, for example) The disk I'm referring to is the Hitachi Deskstar HD32000. Though I couldn't find that exact model on Hitachi's support site, these are the power requirements for a similar drive, the 7K2000 (2TB, 7200RPM, SATA II): Power Requirement +5 VDC (+/-5%) +12 VDC (+/-10%) Startup current (A, max.) 1.2 (+5V), 2.0 (+12V) Idle (W) 7.5 From what I've read, 2.5" drives require 5V, meaning that my MacBook obviously is capable of producing it. The specs seem to suggest that this drive seems capable of accepting it instead of the typical 12V - is this an accurate interpretation of the power requirements? Or does it need both 12V and 5V?

  Read the article

• What is the fastest way to clone an INNODB table within the same server?

  - by Vic

  Our development server is a replication slave of our production server. We have a script that developers use if they want to run their applications/bug fixes against fresh data. That script looks like this: dbs=( analytics auth logs users ) server=localhost conn="-h ${server} -u ${username} --password=${password}" # Stop the replication client so we don't encounter weird data. echo "STOP SLAVE" | mysql ${conn} # Bunch of bulk insert optimizations echo "SET autocommit=0" | mysql ${conn} echo "SET unique_checks=0" | mysql ${conn} echo "SET foreign_key_checks=0" | mysql ${conn} # Restore all databases and tables. for sourcedb in ${dbs[*]} do destdb=${prefix}${sourcedb} echo "Dropping database ${destdb}..." echo "DROP DATABASE IF EXISTS ${destdb}" | mysql ${conn} echo "CREATE DATABASE ${destdb}" | mysql ${conn} # First, all the tables. for table in `echo "SHOW FULL TABLES WHERE Table_type <> 'VIEW'" | mysql $conn $sourcedb | tail -n +2`; do if [[ "${table}" != 'BASE' && "${table}" != 'TABLE' && "${table}" != 'VIEW' ]] ; then createTable=`echo "SHOW CREATE TABLE ${table}"|mysql -B -r $conn $sourcedb|tail -n +2|cut -f 2-` echo "Restoring ${destdb}/${table}..." echo "$createTable ;" | mysql $conn $destdb insertData="INSERT INTO ${destdb}.${table} SELECT * FROM ${sourcedb}.${table}" echo "$insertData" | mysql $conn $destdb fi fi done done echo "SET foreign_key_checks=1" | mysql ${conn} echo "SET unique_checks=1" | mysql ${conn} echo "COMMIT" | mysql ${conn} # Restart the replication client echo "START SLAVE" | mysql ${conn} All of these operations are, as I mentioned, within the same server. Is there a faster way to clone the tables I'm not seeing? They're all INNODB tables. Thanks!

  Read the article

• Mounted HDD not having enough permissions from Apache/PHP

  - by Dan

  Piwigo gallery, on apache and php, CentOS 6. The root system is a RAID 128GB. /var/www/html is on the root file system. Mounted the 320GB hdd to /var/www/html/320 using defaults, it's an ext4 fs. Put a symlink to it in /var/www/html/galleries which is read by the gallery script so I can upload images to there, then click sync. It gives me the error: [./galleries/] PWG-ERROR-NO-FS (File/directory read error) PWG-ERROR-NO-FS: The file or directory cannot be accessed (either it does not exist or the access is denied) chmod 777 set on /dev/sdb1, /var/www/html, and /var/www/html/320 as well as the symlink galleries too. All recursive. chown apache:apache to everything too. PHP just can't read/write to it. I tried with and without the symlink, I've tried everything I can think of. Nothing. Any ideas how I can give apache/php permission to read/write to this drive? With 777 permissions all around it should already be able to.

  Read the article

• big cpu load on vmware server / linux

  - by dezfafara

  Hi, I currently using a server 2.x hosting 4 virtual machines on a linux system Today, on my physical server, I saw an enormous load average: this is the "top" of the server, illustrating my 4 virtual guests. top - 11:02:02 up 194 days, 23:09, 5 users, load average: 18.78, 12.05, 13.55 Tasks: 113 total, 4 running, 109 sleeping, 0 stopped, 0 zombie Cpu0 : 71.6%us, 19.0%sy, 0.0%ni, 8.8%id, 0.0%wa, 0.3%hi, 0.3%si, 0.0%st Cpu1 : 74.3%us, 10.4%sy, 0.0%ni, 15.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 72.5%us, 17.6%sy, 0.0%ni, 9.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 79.5%us, 4.6%sy, 0.0%ni, 16.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8178884k total, 8129980k used, 48904k free, 134904k buffers Swap: 10490436k total, 148k used, 10490288k free, 6129728k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7312 root 6 -10 1149m 921m 559m R 97 11.5 107947:09 vmware-vmx 6995 root 6 -10 779m 687m 317m R 92 8.6 107374:31 vmware-vmx 6693 root 6 -10 880m 659m 409m S 85 8.3 76947:33 vmware-vmx 12937 root 6 -10 960m 719m 523m S 75 9.0 67219:49 vmware-vmx In bold are the cpu usage for my 4 virtuals guests These guests are running on a linux system, and the appropriate process are usually 5% - 15% of cpu I don't understang why , since a few days I have this big problem. This is the "top" on a virtual guest which is at 95% of cpu load top - 11:23:15 up 194 days, 23:13, 4 users, load average: 0.25, 0.47, 0.59 Tasks: 92 total, 2 running, 90 sleeping, 0 stopped, 0 zombie Cpu(s): 1.4%us, 7.7%sy, 0.0%ni, 90.5%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 382296k total, 369732k used, 12564k free, 145156k buffers Swap: 979924k total, 13956k used, 965968k free, 86988k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3691 root 20 0 23948 1148 960 S 13.0 0.3 15339:23 vmware-guestd 3840 root 20 0 19880 584 512 S 7.7 0.2 1729:17 hald-addon-stor This virtual guest state is ok ... If anyone has any ideas .. Thanks

  Read the article

• VirtualBox: using physical partition as virtual drive

  - by Hamman Samuel

  Background: I am using VirtualBox installed on Windows 7. From within VirtualBox I am using Xubuntu as a virtual OS. The reason I chose this approach is so that I don't have to keep turning off Windows and rebooting from Xubuntu every time I needed to switch OSes. And VirtualBox's seamless mode is pretty amazing to allow me see Xubuntu and Windows 7 all in one screen. Issue: Now I am thinking of a way to have Xubuntu more integrated into my system. By this I mean I want to have a physical partition for Xubuntu. But I want to still have the feeling of the seamless mode. Question: So finally, my question is: is it possible to load a partition in VirtualBox as a virtual OS? Case examples: Ideal scenario would be: I physically boot up and login to Windows 7. Now I want to access Xubuntu, so I load VirtualBox and access my Xubuntu partition without rebooting. And the other way around too, i.e. I boot up the system, login to Xubuntu, and can access the actual Windows 7 partition through VirtualBox. Other info: Please note that I am not talking about getting access to files, as I have a completely separate partition for my files, and am very familiar with VirtualBox's Shared Folders option.

  Read the article

• Seemingly random network connectivity.

  - by AngryHacker

  This has been driving me nuts for a while. When I turn on the PC (which has a wired Ethernet connection), it cannot be accessed by other computers on the network. In other words, inbound connections do not work. The firewall is disabled. The PC itself can hit up anything it wants just fine. By process of elimination, I've figured out that checking or unchecking the Eaclift driver in the properties for my network connection restored the inbound connection. I do not know what Eaclift driver is or does or how it even got on my PC (e.g. I am not allowed to uninstall it either). And it does not matter whether it's on or off - I just need to toggle it to restore connectivity. One other thing that happens when I toggle the Eaclift driver, is than an Internet Connection icon appears in the Network Connections and it was not there before. Can someone shed some light as to what is going on? How to fix it so that I don't have to deal with this insanity?

  Read the article

• Default IPv6 route on debian squeeze does not come up after boot

  - by Georg Bretschneider

  I have a problem with my default IPv6 route not coming up after boot on a Debian Squeeze system. This is my config (/etc/network/interfaces): # Loopback device: auto lo iface lo inet loopback iface lo inet6 loopback # device: br0 auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 88.198.62.xx broadcast 88.198.62.63 netmask 255.255.255.224 gateway 88.198.62.33 up route add -net 88.198.62.32 netmask 255.255.255.224 gw 88.198.62.33 br0 iface br0 inet6 static address 2a01:4f8:131:10x::2 netmask 64 gateway 2a01:4f8:131:100::1 up route -A inet6 add 2a01:4f8:131:100::1/59 dev br0 My inet comes up alright, but I have to exec the route command manually after boot to make IPv6 work. Otherwise I can't even reach my gateway. This is the output of ip -6 route show after boot: 2a01:4f8:131:10x::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 unreachable fe80::/64 dev lo proto kernel metric 256 error -101 mtu 16436 advmss 16376 hoplimit 4294967295 fe80::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 I already tried it with: up ip -6 route add 2a01:4f8:131:100::1 dev br0 up ip -6 route add default via 2a01:4f8:131:100::1 dev br0 in /etc/network/interfaces, but with the same results. If I execute those commands manually on my shell, everything starts working nicely. And yes, I tried with post-up instead of up, too. Only other changes I made was to activate ip forwarding for IPv6, because I want to run some LXC containers on that system.

  Read the article

• Windows 7 hangs with 100% disk activity but only when online

  - by jeremy

  I have the same problem as seemingly many other people here, and I think we might all be experiencing the same issue: a compatibility issue in Windows 7 between hard drive and network controller or drivers. I've tried firmware updates of my entire board, wiping my drive and reinstalling from scratch. And yet the problem persists, which suggests it is an operating system error, as the hard drive checks out 100% physically. Additionally, the only time it does not occur is when in safe mode WITHOUT networking. With networking, there are spikes in disc access every so often and a huge flow of processes accessing the disc simultaneously that literally "stick" the disc, and physically jolting my computer unsticks it. Again, this has been tested for hours in a professional service environment, and without network access on, things are fine. As soon as there's network access available, the disc access occasionally cranks up to 100% and sticks everything. I'm using Microsoft Security Essentials, but this also happened under Norton, then McAfee. Again, this happened again after a complete wipe, so the likelihood of malware causing it seems low. I don't visit unsecure sites anyway, as far as I know. This, to me, narrows it down to a Windows 7 process that is somehow repeatedly corrupted, perhaps a corrupt .dll or driver, causing a conflict at the operating system level and temporary hard drive failure. I would encourage anyone who knows more about this stuff (which is probably most people!) to take a shot at this one, and I would encourage anyone else with a sticking hard drive in windows 7 64-bit to check on whether it occurs during safe mode without networking.

  Read the article

• Cloning a NAS drive which hosts a SQL Server DB

  - by Adrian Hand

  We have a system in the field running a server application which is suffering with major performance issues. The system in question has 2 onboard 300gb sas drives in RAID 5 from which it boots Windows Server 2003, and a 6tb buffalo terastation NAS unit (also RAID 5) to which the server app does all of its reading and writing. I believe the terastation is the source of all our woes. Whilst under load, reads and writes tick by at something of the order of 1meg/sec, though the network in question is hardly utilised. The terastation contains various data, but crucially hosts a full instance worth of SQL Server .mdf and .ldf files (master etc - the whole shooting match) I wish to stop all the services on the server, then take everything on the terastation and essentially clone it to some alternative onboard storage, so as to eliminate the terastation from the equation as far as poor performance is concerned. ie the terastation is currently drive D: - I want to copy everything off and then have the duplicate assume the drive letter so that as far as the software is aware, nothing is different. This is tricky because of the mdf and ldf files - everything else will work with a straight up file copy. Can anyone suggest a means to achieve what I am describing? Many thanks!

  Read the article

• keyboard intermittently stops working, even after reinstalling windows 7; possibly a Chrome issue?

  - by neverskipbreakfast

  My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash a couple of the ctrl+alt+windows type keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu, but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) *Unplugging & reconnecting keyboard does NOT fix it. *Connecting a different keyboard does NOT fix it. That one won't work, either. *Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. *Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears, they keyboard won't work, and neither will the icon to pull up the on-screen keyboard. Otherwise my mouse can click around just fine. I can only log onto a non-password protected account. *Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. *Clearing my Chrome browsing data stopped the problem from recurring for a week or so. *I use Avira free antivirus software, and repeated scans turn up nothing fishy. *I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. The only thing I suspect is something in Google Chrome -- I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

  Read the article

• How configure 2 Lan cards in Windows 7/8 pc one to connect to Internet and other to Local Network

  - by Maharshi Raval

      I am about to install a dedicated VOIP server in our office. It is a 3CX pbx system on Windows 7/8 machine. The environment currently is a Windows SBS 2011 with 8 client machines. I want to use a dedicated broadband connection for the PBX (3CX) box, but the box also needs to be accessible in the local network as we will be using IP Phones and software IP phones. How configure two network cards on PBX box, so that one will be always used to connect to our SIP host over the Internet and the other will be connected to local network accessible from other client pc to connect to the pbx system. It must be noted that currently the Windows SBS 2011 acts as the Primary Domain Controller and gateway for all the client machines.     I cannot use a load balancer as it will conflict and cause issues within the current setup of our SBS2011 as it is also our Exchange Server. Any input is much appreciated. thanks in advance

  Read the article

• How configure 2 Lan cards in Windows 7/8 pc one to connect to Internet and other to Local Network

  - by Maharshi Raval

      I am about to install a dedicated VOIP server in our office. It is a 3CX pbx system on Windows 7/8 machine. The environment currently is a Windows SBS 2011 with 8 client machines. I want to use a dedicated broadband connection for the PBX (3CX) box, but the box also needs to be accessible in the local network as we will be using IP Phones and software IP phones. How configure two network cards on PBX box, so that one will be always used to connect to our SIP host over the Internet and the other will be connected to local network accessible from other client pc to connect to the pbx system. It must be noted that currently the Windows SBS 2011 acts as the Primary Domain Controller and gateway for all the client machines.     I cannot use a load balancer as it will conflict and cause issues within the current setup of our SBS2011 as it is also our Exchange Server. Any input is much appreciated. thanks in advance

  Read the article

• How does one skip "Windows did not shut down successfully" in Win7-64?

  - by XenonofArcticus

  Migrating an app from an expensive and unreliable dedicated embedded x86 box running WinXP-embedded to COTS hardware (Dell E6410 laptop) running normal Win7-64. At this time, it's not feasible to deploy using Windows 7 embedded. The problem is, that the system is still sort of "embedded". The power could shut off at virtually any time without prior warning. We've stripped the OS down and removed the battery capability so that it will power down as desired. The app never writes to the disk, so it's not like we're going to corrupt anything terribly. The system is essentially idle after our app is up and running (with the exception of some computation, graphics, and TCP/IP and serial communications) so the OS enters a pretty stable state rather quickly. After a power-loss however, it rightly complains that Windows did not shut down successfully and presents the user with the Windows Error Recovery text screen. If left alone, it does eventually move on booting just fine, but we'd like to skip that step if possible. WinXP-embedded is designed to do this automatically, so I know it's possible. I've looked at the Kernel Switches but I didn't see anything documented for "Skip Windows Error Recovery". I've also read extensively on the startup process: http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/windows-nt-6-boot-process.html I know I can disable the auto chkdsk in the registry, but that's not the same thing either. So, how do I streamline the boot process to not hassle the user about a situation that will be the regular normal situation?

  Read the article

• Getting prompted for password accessing page through script even when client and server are in same

  - by Munawar

  I'm trying to pull up an internal webpage in automated fashion using the methods in 'Internetexplorer.Application' using vbscript. But I'm getting prompted for password, although the client and the server both are in the same domain. Predictably when I manually try to access the web page, I don't have any problem. Only when I try using cscript.exe or iexplore.exe, I get prompted. I'm trying to automate some of the smoke test we do after a new build is deployed. But this password prompt is getting in the way. Following are the system specs Client machine - IE 7.0, OS is Windows server 2003 Server machine - Windows Server 2008 Both are in the same domain. So far I've unsuccessfully tried following to automate the password input system.diagnostics.process.start var WinHttpReq = new ActiveXObject("WinHttp.WinHttpRequest.5.1"); WinHttpReq.Open("GET", "http://website", false); WinHttpReq.SetCredentials("username", "password", 0); Nothing seems to work I checked in IIS. we have only anonymous and forms authentication enabled Is there any configuration setting in the client machine that can be tweaked to bypass this, although I'd hate to do it since you step on the toes of twenty people trying to do that. Preferable way would be to programmatically input it if its possible. Also, if you can suggest a more appropriate forum, that'd be great too. Please help.

  Read the article

• Moving hidden files/folders with the command-line or batch-file

  - by Synetech

  Question Does anyone know of a way to move files and folders that have the hidden, system, or read-only attribute set from the command-line or a batch file? (No, stripping the attributes first is not an option since there is no practical way to know which attributes were set in order to re-set them after the move.) (Failed) Attempts Using the basic move command does not work with items with the hidden or system attribute set and for some reason, it does not have switches to specify attributes like the dir and del commands do. I tried using a utility I wrote that uses the shell’s file operation function, but that requires using start /w to prevent the batch file from running on ahead, and it complains about long-filename support for some reason. I tried using robocopy, but it first copies the files and then deletes the originals instead of simply moving the source (which results in a frustrating delay, even with the excessive output redirected to nul). (Surprisingly it seems that few people have ever needed to move hidden files from the command-line. All I could find was this one person who abandoned the attempt.)

  Read the article

• Oracle: Getting ORA-01195 and ORA-01110 when attempting resetlogs

  - by MacAnthony

  I am trying to get our database to startup. When I login to sqlplus and do a startup, I get the message: Total System Global Area 534462464 bytes Fixed Size 2215064 bytes Variable Size 331350888 bytes Database Buffers 192937984 bytes Redo Buffers 7958528 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open So I do a shutdown, startup mount (which works fine) and then run: SQL> alter database recover using backup controlfile until cancel; alter database recover using backup controlfile until cancel * ERROR at line 1: ORA-00283: recovery session canceled due to errors ORA-19909: datafile 1 belongs to an orphan incarnation ORA-01110: data file 1: '/<path>/system01.dbf' SQL> alter database open resetlogs; alter database open resetlogs * ERROR at line 1: ORA-01195: online backup of file 1 needs more recovery to be consistent ORA-01110: data file 1: '/<path>/system01.dbf' I know I've used instructions to get me past this error before, but I seem to be having trouble tracking it down. A bit of history: We wanted to refresh the data in this from another db so we attempted to do a expdb/impdb into this instance. The impdb did not complete correctly and got an end of file error message in it and hung (I still have the message in a log if it's important). Since the instance would start at this point, we decided to use the hotbackup process we have to restore the db. The hotbackups are from another server/instance. We went through the same process 2 weeks ago. At the point of recreating the control file is where we got to the issue above.

  Read the article

• Transferring an SQL Processor License to a virtual hosted environment

  - by Andrew Shepherd

  My company is currently hosting a service in-house, and we want to move to an externally hosted environment. We would then be using a virtual server. I understand that this might be spread across multiple machines, but from my perspective as a customer, this layer is abstracted away - I shouldn't know or care about the hardware that the OS is hosted on. We have a licensed edition of SQL Server 2008. This is one Processor license. Will it be a violation of the licensing agreement to use this in a virtual environment. From the reference guide here it says When licensed Per Processor With Workgroup, Web, and Standard editions, for each server to which you have assigned the required number of per processor licenses, you may run, at any one time, any number of instances of the server software in physical and virtual operating system environments on the licensed server. However, the total number of physical and virtual processors used by those operating system environments cannot exceed the number of software licenses assigned to that server For enterprise edition there is an added option: if all physical processors in a machine have been licensed, then you may run unlimited instances of SQL server 2008 in one physical and an unlimited number of virtual operating environments on that same machine. I'm having trouble getting my head around this. Would I theoretically have to get a license for every processor in this virtual environment (which is effectively impossible because I have no way of knowing how many processors there actually are)? Or can I just say that it's hosted on one "virtual" server, so that's OK?

  Read the article

• How do I fix error 1303 during TI Connect install?

  - by smoth190

  I recently purchased a TI-84 Plus graphing calculator, and I'm trying install the TI Connect software in order to connect the calculator to my computer via the USB cable. Unfortunately, I'm getting this error while trying to install the program: Error 1303. The installation has insufficient privileges to access this directory: E:\Data\Timothy\Documents\MyTIData. The installation cannot continue. Log on as administrator or contact your system administrator. However, my account is the only account on my PC, and it has administrative privileges. I've also tried running the installer with Run as Administrator, but with no luck. If I create the folder MyTIData manually, I receive this error: Error 1317. An error occurred while attempting to create the directory: E:\Data\Timothy\Documents\MyTIData I've reapplied the security settings to the E:\Data folder (and all its sub-directories) to Full for my account. I've also gone into Computer Management, and given SYSTEM full privileges for the entire disk. I've also logged out, logged back in, restarted, etc. but still, no luck. Now, I should mention that my Documents folder is not at the default location. I changed it due to my C: disk being a 90GB SSD, so I moved all my personal data onto the extra storage disk (which is ~1TB). I don't know if that is causing the issue, but it can't hurt throwing it out there. So why can't I install this program? Google'ing the problem brings up this error for various other installers (such as Visual Studio and Microsoft Office), but nothing for TI Connect. All the solutions are the same: Give the folder Full privileges...but I've already done this! I've also tried running the installer with and without the calculator plugged in, but it didn't change anything. In the prompt that contains the error, repeatedly clicking Retry or waiting a few moments before clicking Retry also produces no result.

  Read the article

• Hibernate between OS X and Bootcamp Win 7

  - by Willem

  Wouldn't it be great if someone wrote a guide or an app which allowed you to switch instantly between OS X and Windows using Hibernate in both OS:s? Windows 7 already has an option "Hibernate" which allows you to boot back to your OS X partition, but OS X does not exactly offer the same. However, there are possibilities here. It seems that the recent Mac's have 3 different kinds of sleeping mode: Sleep: Low power consumption, RAM still active. Legacy Safe Sleep: No power consumption(?), writes RAM to disk and shuts down (is this the same as Hibernate?) Safe Sleep: Writes RAM to disk and enters sleep mode. If battery level drops too low it goes into Hibernate (is this Hibernate the same as #2 in this list? This is the Hibernate I will be referring to int he rest of this post) It seems that I am unable to force my MacBook Pro (Late 2011) OS X 10.7.3 into a true hibernate using either command line or apps that are supposed to do this. I believe the Mac should show that white loading bar whilst waking up if it was truly put into hibernate (which it does not). But I can get this white bar to show by letting my battery level drop to 0% so there is obviously a system function for it (obviously, duh! :). When Win 7 goes into hibernate it shuts down completely and you can then boot into OS X on startup. On OS X however, hibernate forces you to wake up into OS X. Can you hack this so that you're allowed to select boot partition after OS X hibernates? Would it be possible to use the true hibernate system functionalities of Win 7 and OS X to create a kind of instant switching between the two? Imagine this on a quick SATA-3 SSD like my 180GB Intel 520. Thanks / Willem

  Read the article

• Removing extended partition without deleting logical in it

  - by HisDudeness

  I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

  Read the article

• Best way to build / implement a corporate developer Linux distro with multiple kernels?

  - by Garen

  At work we have Linux users who understandably prefer using Ubuntu. Problem is, we also have developer tools that only work with 'officially' supported Linux distributions that use much older 2.6.18 based kernels. (And even if they worked with newer ones, the vendors could always say they won't "support" the software unless it's on one of their 'officially' supported platforms.) We could of course just tell them to use CentOS or something else 2.6.18-based, and I'm sure their response would be something like: "you can take Ubuntu from our cold, dead hands." :) Which brings to me some questions--is there any good/easy/recommended way to run something like Ubuntu as a host VM and Centos 5.x as a guest OS (with which system--Xen,KVM,VMWare, ...?), and then roll that into our own custom internal distribution that could be easily installed? KVM looks like a good high-performance option just recently included in RHEL 5.4, but if hardware support for virtualization like Intel-VT or AMD-V is necessary, then I'd guess only those folks with fairly new PCs will be able to do it. Would be very interested to hear how anyone else has addressed this kind issue. EDIT: The target audience / users of this kind of system would be developers, each one needs to run locally licensed commercial software, so building out some separate beefy central machines isn't an option unfortunately due to license restrictions. Even if that weren't the case, a couple developers could quickly eat up the resources with parallel builds. :) Ideally, I was hoping there was some step-by-step guide out there to build your own pre-built distribution that had e.g. CentOS 5.x and Ubuntu Desktop as a guest.

  Read the article

• Windows VirtualBox failed to attach USB device to Linux Guest

  - by joltmode

  I have Windows 7 64bit Host system, and I am using VirtualBox 4.1.18 (r78361). I have an Arch Linux Guest OS. I have installed VirtualBox Extension Pack (to enable USB2 support) and added my USB device filter to VM. I have also installed the Guest Additions provided by Arch: virtualbox-archlinux-additions (but I have no idea whether it's actually needed for my environment). I can see my USB device from VirtualBox Devices menu. Whenever I am trying to access it, I end up with: Failed to attach the USB device Kingston DT 100 G2 [0100] to the virtual machine Archlinux. USB device 'Kingston DT 100 G2' with UUID {a836ec33-0f41-4ca7-a31d-09cceaf5d173} is busy with a previous request. Please try again later. Details ? Result Code:    E_INVALIDARG (0x80070057) Component:      HostUSBDevice Interface:      IHostUSBDevice {173b4b44-d268-4334-a00d-b6521c9a740a} Callee:         IConsole {1968b7d3-e3bf-4ceb-99e0-cb7c913317bb} From what I have googled, most guides shows how to solve this the other way around - Linux Host to Windows Guest. How do I resolve this? Update I have tried to Eject (virtually, not physically) the device from my Windows Host system and then try to access the Device from Guest. Same error.

  Read the article

• 2 subnets off of 1 PC with 2 NICs

  - by Jeff

  I have a general setup I'd like to do with some IP cameras. This seems like it will work but I think I may be missing something. Our system consists of a video recorder PC connected to a switch which is connected to a number of IP cameras. I'd like to connect this system into an existing network but I want it on a different subnet. The main reason is that the cameras use a lot of bandwidth that I don't want slowing down the existing network. My idea was to install 2 NICs on the video recorder pc. 1 NIC connects to the existing network on 192.169.1.x for example, and the other NIC connect to the switch with the cameras. This NIC would be 192.168.100.x. Then we could remote to the video recorder PC with a GoToMyPC type thing for administration via the existing network. I've included a diagram of how I see this working but I'm a little fuzzy on the setup of the NICs (if this can work at all). My problem may be trying to deal with 2 subnets without a router but It really doesn't seem like it's necessary in this situation. BTW, gliffy is cool.

  Read the article

< Previous Page | 821 822 823 824 825 826 827 828 829 830 831 832  | Next Page >