Search Results

Search found 67891 results on 2716 pages for 'windows virtual pc'.

Page 833/2716 | < Previous Page | 829 830 831 832 833 834 835 836 837 838 839 840  | Next Page >

• Issues regarding internet connectivity

  - by andySF

  Hello. My problem started when Yahoo Messenger stopped connecting. I've tried to see if Internet Explorer was working but will not load any page. The diagnostics of Internet Explorer says that is something wrong with my dns(using just ip of google or yahoo or my local webserver was not working). I use Windows 7 and at the moment i've had Internet Explorer 8 and after a lot of failing updates to ie9 I've successfully install the Romanian version of IE9(now i have ie8 after a system restore). Then I installed the service pack 1. I've done a lot of things and I will try to enumerate them, but my problem persists. Settings from Yahoo Messenger and Internet Explorer are OK. I've try to reset winsock and ip from netsh. I've scanned my pc with spybot, mallwarebytes, Trojan Remover(simplysup), Loaris Trojan Remover, Avast, Nod32, Kaspersky, Bitdefender,alot of registry cleaner including CCleaner and maybe others that I cannot remember now. I reset the registry permissions using subinacl. At a moment my files permissions was set jut to "trusted installer" and I've put the permission back to files and folders using the model of other windows 7 machine. I have try so many things that now i'm stuck in a loop using different security tools to check for problems. Oh, and my virtual machines are working just fine.(I'm using VirtualBox) Please Help. PS, Reinstalling Windows is not an option. Thank you!

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• While using an ntfs smb share for mac users, do symbolic links and extended attributes work?

  - by scape

  We have a majority of mac users but we'd rather support their file sharing using a Windows server with an ntfs drive, or at least a Linux server with ext3. We've had trouble, much trouble, utilizing the OS X server software and after the years are now looking to abandon it. What's mostly holding us back is the fact that the mac users very often utilize symbolic links and other special features that exist for an HFS+ partition. The shared locations are mostly primary storage and not just used as an archive storage location. While there is an option to create symbolic links under ntfs, I'm curious if there is anything I need to look out for if I were to move the files over to a new partition that's hosted from a Windows server from the HFS+ partition; in addition, how well creating a symbolic link from a mac might work. I am also worried about windows backup software and if it will ruin these special sym links, and how placing permissions on sub-folders will work. Alternatively I could remotely backup the files using a mac and Bru, nonetheless I still want to get away from mac server for hosting the shares.

  Read the article

• IIS7 can't read web.config on shared Mac filesystem

  - by RobG

  I'm running a VirtualBox virtualized Windows 2008 Server on my Mac, just finished setting it up today. On it, I have SQL Server 2008, IIS and ColdFusion 9. I want to serve websites from my Mac filesystem (for development purposes). So I created a new website in IIS and pointed it at the appropriate path using a UNC path: \vboxsvr\rob\Sites\testsite, which contains the ColdFusion code and a web.config file. When I attempt to modify the file at all, or view the site in a web browser, I get an error: HTTP 500.19 - Internal Server Error The requested page cannot be accessed because the related configuration data for the page is invalid. I did some Googling, and found several similar problems, but nothing exactly like I have. The closest one seemed to indicate permissions. So I recreated the site and set it up to allow the Administrator (in Windows) to access the stuff. That didn't help. I can read/modify the files just fine from within Windows, but IIS itself can't seem to do it. What do I need to do to fix this? Thanks!

  Read the article

• Vista won't boot. BSOD: Page fault in nonpaged area

  - by user31576

  Here's the story: I let Windows Update do the updates it wanted to do, then rebooted the computer. The updating process was taking time so I went away. When I came back, my computer was rebooting. It got as far as the Windows logo with the laoding bar. BSOD'd. Rebooted. And I'm stuck in this loop ever since. Looked up on the net, the "Page fault in nonpaged area" seems to be linked to faulty RAM or drivers. So I ran a memory test, it found no error. When I try in safe mode (with promt) I can see a list of drivers being loaded, then I get the same BSOD. I tried to repair using the Vista DVD, it says "nothing to repair". I tried to restore to a previous state, it says "no restore point found". So, my guess is, it's got something to do with the drivers. How can I identify the one causing the BSOD? If you have any other leads, What can I do? By the way, I'm writing from this very computer, running a linux distro I installed after the BSOD loop started. So i guess it's not an hardware issue. I have backed up important data, and will format and reinstall Windows if I must. But I'd like to avoid that. Thanks in advance for any help you can give me.

  Read the article

• Move EFI System Partition to another drive

  - by Pincopallino

  I had a Windows 8 installation on an HDD, using UEFI as boot. The HDD has the following GPT table: DISKPART> list partition Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Ripristino 300 Mb 1024 Kb Partizione 2 Sistema 100 Mb 301 Mb Partizione 3 Riservato 128 Mb 401 Mb Partizione 4 Primario 390 Gb 529 Mb Partizione 5 Primario 540 Gb 390 Gb (I apologize it's in Italian, but the translation is quite straightforward). I recently bought an SSD drive, connected it and installed a fresh Windows 8. Now I have a working dual boot, but the UEFI partition is on the HDD instead of the SSD. Here's the SDD partition list: Partizione ### Tipo Dim. Offset --------------- ---------------- ------- ------- Partizione 1 Riservato 128 Mb 1024 Kb Partizione 2 Primario 221 Gb 129 Mb I think that the best solution would be to have it on the SSD for two reasons: the first is performance (I guess it would be a little be faster on the SSD due to the spin up time for an HDD, but I may be wrong about that) second reason is consistency. As I plan to use only the Windows 8 installation that is located on the SSD and I'm probably going to erase the system partition on the HDD to use it as a data storage device, I think that the boot partition should be on the same drive as the OS. So the question is how do I move the EFI System Partition to the SSD?

  Read the article

• Running Visual Studio 2010 in a University Campus

  - by Woondows

  We have just installed Windows 7 Enterprise x64 in one of our computer labs being used by students for programming. However, when we installed Visual Studio 2010 Ultimate on the machines, we found that to even launch the application (devenv.exe), required the student to enter the administrator password (the usual UAC prompt). Of course, we could just turn off UAC, but that would defeat the purpose of having it in Windows 7. On the other hand, we cannot really give the students local administrator privilege, as we are concerned that they will do some malicious stuff on the computers. Previously when we used Windows XP Professional running Visual Studio 2005, we had no problems. Kindly advise if there's any workaround for this. EDIT: Thanks for the answer guys. Mayank, your links may work for Visual Studio .Net, but it doesn't seem to work for Visual Studio 2010. Ryan, Tieson, I'm intrigued that you guys managed to get it working easily. FYI I don't manage the Group Policies, but I can get them changed if necessary. Any particular GP that I should be looking at? Suggestions to how to troubleshoot further why UAC is being invoked? At least now I know for sure that this is not supposed to be the default behaviour for Visual Studio 2010 so I'm going to keep digging for a solution. Will try running Procmon and see if i can find something..

  Read the article

• How do I restore to a delta file (disk) on Vmware ESXi

  - by Oscar

  Using VMware Server ESXi (freebie version) I have a Virtual Machine (win 2k3 r2 server). When I first provisioned it I took a snapshot of it. I recently tried to clone the primary drive using my standard hardware-based method to grow a windows disk. (using knoppix, clone drive to a new drive, make it bootable, then I intended to extend the partition via diskpart from within windows). This process failed; I tried setting the cloned drive (via the vmware gui) to replace the original drive, boot and be done. This didn't work out so well. The machine never booted. I checked the boot order, the disk location and all the basics I usually do. As a failsafe, I then tried changing all the settings back so the machine would boot to the original drive and I could figure out (as I eventually did) a better way of growing the disk. However when I powered on the machine with the original drive, it reverted back to that initial snapshot I created; It lost all the changes since. I looked in the file system and found a few files, I think the keyfile here is one named "delta" and I'm assuming that's the disk I want, but I can't find a way to have the Virtual Machine actually use that drive/file. It isn't available to add when I go to add an existing drive. Do I need to somehow commit that delta to the original drive and then boot from it again? Can you point me in the right direction? I've since discovered the proper way of growing drives using "vmkfstools" but I need to get back to the original state of the machine to try this out. Any help would be greatly appreciated.

  Read the article

• Strange WiFi problem - network is "not connected" but works

  - by GalacticCowboy

  Background I'm using a Windows XP tablet PC connected to my home network. I do broadcast the SSID, but otherwise the wireless network is locked down as tight as I can make it - WPA2 with a strong key, MAC filtering, etc. I've had this computer for about 4 years and the router for about 6 months. Before that, the previous router was set up in the same way, and I've never had any particular problems. Problem This morning - as I type this, as a matter of fact - Windows is reporting that none of my network connections are connected. Yet somehow my Internet connectivity still works! ipconfig reports a valid IP address, domain, etc., even though Windows apparently doesn't know about it. I tried repairing the connection and it had no effect - the repair eventually timed out. I'm pretty sure that I could reboot the computer and/or the router, etc. and it would fix the problem. However, I'm more interested in knowing if any of you have ever seen anything like this, and what might have caused it? Since it works I'm not inclined to mess with it too much. My concern is that it's a precursor to bigger problems.

  Read the article

• Acrobat 9 Pro - shortcut key failure

  - by Rick G

  I create numerous Acrobat PDF files from MS Word documents via Acrobat 9 Pro. I often need to print a single page from an Acrobat PDF file. I normally use the keyboard shortcut Control-P (Print Dialog) and ALT-U (current page). I recently set up a new PC with Windows 7, and this shortcut combination does not work. When I press ALT-U, it moves the highlight to the correct item, but does not select the radio button. If I press the Enter key, then I print the entire document instead of the current page - VERY annoying! It looks like there is an error in the design of the Print dialog for Acrobat. There are two items which have ALT-U as the keyboard shortcut. They are "Current page" in the Print range frame, and "Summarize comments". I have been able to use Control-P (Print Dialog) and ALT-U (current page) with no problems on virtual machines and older computers running Windows XP. Maybe I installed some software on the new PC that is messing up the keyboard shortcut. Is there any way to figure out the culprit - or is this a known problem with Acrobat?

  Read the article

• Intermittent Trouble Entering Hibernate on WinXP

  - by kquinn

  My personal desktop, running 32-bit Windows XP SP2 (with 4GB RAM, 2.75GB addressable, swap disabled, hiberfil.sys existing and contiguous on C:\; SP3 is not installed because SP2 has been working fine and I do not want to re-qualify with SP3 just for sheer perversity) typically gets hibernated at night. For a long time this worked great, but recently the machine has had trouble entering hibernation. Sometimes when I press my power button (configured to hibernate), the box will start the procedure for hibernating (i.e., go to the blue "Windows XP" background logo and display a message about entering hibernation), but before displaying the usual blue-on-black hibernation progress bar it will drop back to the desktop. No error messages appear, on screen or in the system log. The only record of unsuccessful hibernation attempts in the system log, which proudly proclaims that "The Windows Image Acquisition (WIA) service entered the running state." once per failed hibernation attempt. The problem is almost certainly resource related: if I then close one or more applications which are running, and repeat the exact same process, the machine will hibernate perfectly. There does not appear to be a reliable high-water mark for virtual or physical memory use, below which the machine is guaranteed to hibernate; it's different every time (though typically, below about 1.1–1.4 GB memory usage seems to be where hibernate succeeds most often). Memory may not even be the relevant resource; as far as I know, it could also be handles or sockets. This behavior is relatively recent: it has only started in the last few months; before then, I could hibernate reliably no matter what the current resource use of the system. This machine claims to have hotfix Q909095 installed, but since the symptoms of my problem match KB909095 rather well, I'm suspicious if this fix is actually working as intended. Any ideas on how to fix this or where to start debugging?

  Read the article

• Win7 'locking' process/files/folders?

  - by Dynde

  I've had a fair bit problems with sometimes files/folders/processes being 'locked' by Windows. The weird thing is, it's not like the traditional sense, I think, where tools like UnlockIT and wholockme would work. It seems that just giving it a little often helps - making me think it could either be the HDD, the memory, or something in Windows. A scenario: I go into a folder - don't open anything at all, go back up, cut or drag-move the folder to someplace else, it says "Action can't be completed because the folder or a file in it is open in another program". Waiting sometimes 20 seconds sometimes a little longer, and I can move it. Another scenario is deleting a bunch of files in a folder, and it appears that everything is gone, but then suddenly after a few seconds an .exe file pops back up, and I can't delete it. Waiting a few minutes, then pressing refresh and it's gone. I have the strangest feeling that there's a problem with either HDD or memory. I already tried disabling Windows indexing service with no luck. Does anyone have any ideas? EDIT: I should say, that I have a very fast system, 16 GB DDR3 RAM, i7-2600k CPU, SSD main HDD, so I really should not be experiencing any sort of problems, where one might say that it's "reasonable" for the system not to respond right away. Edit2: And I updated SSD firmware a couple months ago, so it shouldn't be bad release FW either

  Read the article

• Overscan in Catalyst Control Center

  - by alex

  I've connected my PC to my TV via HDMI (I've also tried using DVI). Whatever the resolution (anything from 800 x 600 to 1080p), the image displayed on the TV does not fill the entire screen surface; there's a black border on the edge of the image. This happens in both Vista and Windows 7. After a bit of searching I came to the conclusion it's got something to do with overscan done by the graphics card (ATI 3200HD). It's definitely not the TV because on my old PC there were no such problems. I've searched for the option in Catalyst Control Center 9.9 but it's not available for the TV; if I connect a normal LCD display, the option is there, but only for the LCD screen. If I choose Configure for my TV, where the overscan option should be, it takes me to the Welcome tab in CCC. How can I make the image fill the entire screen? How can I enable/disable overscan for my TV?

  Read the article

• Setting Remote Desktop to allows IPv6 connections

  - by Garrett

  Setup: Basically I have 3 machines (2 virtual and 1 physical) that I would like to be able to RDP in to from outside my NAT (a router). The VMs are Windows 7 and Windows XP, both fully patched with Teredo installed and working, both running in VirtualBox (their host also has Teredo working, though I'm not sure if that matters). They both have bridged network adapters with promiscuous mode enabled. The physical machine is Windows 7 fully patched with an HFS server running on it and a dynamic DNS set up for my public IPv4 address and port forwarded. It also has Teredo installed and working. Symptoms: According to http://test-ipv6.com/ all 3 have public IPv6 addresses, and they can all connect to http://ipv6.google.com/. I can ping the XP VM from the host it's running on but I cannot ping it from any other machine. Also, I cannot ping either of the other machines from anywhere. I cannot connect to any of them over RDP from IPv6, however I can connect to all of them through IPv4. Any ideas what is going wrong?

  Read the article

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

• Doing arithmetic and passing it to the next command

  - by neurolysis

  I know how to do this in /bin/sh, but I'm struggling a bit in Windows. I know you can do arithmetic on 32-bit signed integers with SET /a 2+2 4 But how do I pass this to the next command? For example, the process I want to perform is as follows. Consumer editions of Windows have no native automated sleep function (I believe?) -- the best way to perform a sleep is to use PING in association with the -n switch to get that many seconds, minus one, of sleep. The following command is effective for a silent sleep: PING localhost -n 3 > NUL But I want to alias this into a sleep command. I'd like to have it elegant so that you enter the actual number of seconds you want to sleep after the command, right now I can do DOSKEY SLEEP=PING 127.0.0.1 -n $1 > NUL Which works, but it's always 1 second less than your input, so if you wanted to sleep for one second you would have to use the command SLEEP 2. That's not exactly ideal. Is there some way for me to pass the arithmetic of $1+1 and pass it on to the next command in Windows? I assume there is some way of using STDOUT...

  Read the article

• How can I avoid my web browser from redirecting to localhost using WAMP in Windows7?

  - by Josh

  I'm currently using Windows 7 with WAMP to try and work on some software, but my web browsers will not accept cookies from the "localhost" domain. I tried creating a few bogus domains in my hosts file by pointing them to 127.0.0.1 but when I type them in I am automatically redirected back to localhost. I have also configured virtualhosts in apache to correspond with the domains I added to the hosts file and it still redirects back to localhost. Is there anything special I must do on Windows 7 to get around this localhost redirect? Thanks for looking :) I'll include my host file here: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost 127.0.0.1 magento.localhost.com www.localhost.com Thanks for looking :)

  Read the article

• How can I install iTunes in such a way that it can't put any "hooks" or helper programs on my computer?

  - by Joshua Carmody

  I'm buying a new iPad, which means I must once again install iTunes. I've not used iTunes in more than 6 months, since I bought a new computer. I don't like iTunes, but I can live with using it to buy/manage media and sync my Apple devices when the program is open. What I would like to do though, is find a way to install iTunes in such a way that it has absolutely no effect on my system when it is closed. iTunes normally installs several helper programs such as iTunesHelper.exe, and the Bonjour service. These programs run in the background when iTunes is closed. You can force-close them, or remove them from your setup files, but iTunes will often put them right back when you run it. I know these programs are mostly harmless, but they have at times caused issues such as iTunes spending system resources trying to catalog media files or drives connected to VPN, or other issues. At best they're just one more small background process eating up a small piece of my CPU time and RAM. How can I run iTunes without letting it get it's "hooks" into my system? One thought I had is that I could create a Windows user account just for iTunes, and deny it admin privileges. Then if I installed iTunes using that account maybe anything it installed wouldn't affect the "main" account on my PC? But I'm not sure if that would work.... Failing that, maybe some kind of virtualization software or sandbox I could install it in? I'm open to any suggestions. My system is an Intel-based PC running Windows 7 Professional 64-bit. Thanks!

  Read the article

• How to track which process is failing logons?

  - by Massimo

  Windows Server 2003, VMWare VirtualCenter 2.5. Something is continuously trying to log on to VirtualCenter using a disabled domain account; the failed logon attempts are logged by VirtualCenter in its own logs and by Windows in the Security event log. This happens roughly every minute or two. The source of the logon attempts is 127.0.0.1, so it must be some process running on the server itself. There are no services running as this user account and no scheduled jobs on the system. The task manager doesn't show any proces running under this account, either. The user account's name is nowhere to be found in the Registry. But some process is trying to use it, and failing. It probably is not some critical process, as everything looks fine; it could be something that was installed long ago and forgotten there. Whatever it is, it probably is running under another user account (possibly a system one), but is trying to log on to VC using those credentials, which are probably saved in some configuration file, since they're not stored in the Registry. How can I track which process is trying (and failing) those logon attempts, either using Windows or VirtualCenter?

  Read the article

• Use GRUB/GRUB2 to PXE boot OS image

  - by Jack

  Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

  Read the article

• Does using a hexacore CPU make sense?

  - by Exa

  I'm currently planning to upgrade my computer system and I want to exchange CPU, board and RAM. I already had a look at some hexacore-CPUs from AMD and would like to know if it makes any sense to use such a CPU with six cores. Is there any software which really uses six cores? Especially in gaming? I'm using this PC mostly for gaming and from time to time for developing. I know that on the dual-core system (2 x 3GHz) I currently use, Visual Studio creates two instances of the compiler, one for each core. Would there be six instances of the compiler on a hexacore system for super fast compiling? Is there any software that uses six cores? Would running two applications cause the usage of more CPUs? (For example two CPUs for a game you're playing while two other CPUs are used for compiling at the same time) I hope someone can point out the benefits of a hexacore system. The OS would be Windows 7 64 Bit and I use the PC for gaming most of the time. (Crysis 2, CoD, stuff like that)

  Read the article

• Host system resets (crashes) when using VMWare or VirtualBox and 64-bit guest systems

  - by sinni800

  I have been trying to install virtual systems on VMWare for a while now and encountered strange behaviour from my PC. The behaviour is as follows: On "automatic" virtualization mode it either outputs a cryptic error message (can MAYBE give later, if I can reproduce) right on startup (before even the BIOS) or it resets the complete HOST system (blackscreen, bios...) If I install a Windows XP on it it works well on "binary translation" mode. If I try installing Linux on it, in "binary translation" mode it crashes 1 or 2 seconds after I hit enter on the GRUB selection screen (after the first page of kernel messages rolled in) Using VirtualBox it crashes right in the BIOS. It gave me a Bluescreen though! 0x00000101: CLOCK_WATCHDOG_TIMEOUT: a clock interrupt was not received on a secondary processor within the allocated time interval NEWS: I tried VirtualBox again and it did not completely crash the computer this time. It gave me a critical error and a log file: http://pastebin.com/yKZSDs91 In conclusion, it will crash instantly if VT-x is activated. If not, it seemingly only crashed if I try to install something with 64 bits. Another update: Yes, it ONLY crashes when the guest is 64 bit! What I tried: Reinstalling Windows (my Windows installation was quite broken so it seemed natural. Didn't work though.) New BIOS What I am certain of: Virtualization extensions are activated in the BIOS What my computer specs are: ASUS P8P67 LE mainboard, newest BIOS/EFI firmware Intel Core i5 2500k Ati Radeon HD 5770 16 GB Corsair 1333mhz DDR3 RAM, 4 X 4 GB

  Read the article

• program to track recent saved files or downloads?

  - by DiegoDD

  Back to windows XP times, i used a program named Ava Find that can find any file in the system, but a really nice feature it had, called "scout bot" that automatically finds new files, that is, recently created. More info here: AvaFind For example, if i saved or downloaded a file (in any program), but i cant remember its name or where i put it, i just simply looked at the scoutbot list, and it showed me the most recent files, and then i could just open them from there, or jump to their path. Since i changed to windows 7 (passing through vista), the program no longer works. It simply keeps indexing forever and never finds anything. I don't know if it is not compatible with win 7 itself, or because the fact that my windows 7 is 64 bit. I already tried to contact the Avafind creators, but they never answered, and the program seems to be no longer supported (although the site still works). Now, is there a similar program that finds RECENT files? e.g. listing the most recently saved files, system-wide (or even limiting it to some folders, discs)? And that of course, that is confirmed to work with win 7 64 bit. I know that there are many programs that can find any file, like everything, but what i want is to find recent files and their paths, without knowing their name or e. "everything" also can sort results by date, which is almost what i need, simply to look for part of the file name or extension, and get the most recent one. but if i get to many results, it takes a while, plus, i STILL need to know the name or at least extension of the file. What i want is simply a "Most recently Saved files" tool. i.e., a replacement for Scout Bot in Ava Find. Do you know any alternative?

  Read the article

• How do I lower the hardware volume? (volume too high)

  - by Zom-B

  I have a 4yo Dell laptop with Windows XP Pro (modern ones unfortunately don't have a physical volume knob), and lately I'm using my Apple earphones, because they have much better low frequency response than my $10 earphones. They also have the side effect of being much louder. To give an indication of my agony, for most tasks (movie, music, games) I have my main volume at 3 ticks: drag to 0 with the mouse and press the up key 3 times (the handle does not even raise 1 pixel) and my wave volume at 50%. I notice that when I do this, I have a lot of digital noise, because I'm using just a tiny fraction of the 16-bit space. If I drag the Wave slider down until I barely hear the audio, it becomes really distorted and noisy, indicating that this is digital volume (in the DirectSound driver or something) and not hardware volume. I experimented in Audition. When I make a tone of 1000Hz at -50db, (all windows volumes at max) the volume is just below my pain threshold. When I zoom in to see how high the sample values reach, I see that just 8 of the 16 bits are used (about -100 ~ 100). When I generate such tone at -80db (minimum I can specify) then I can still clearly hear the tone, although really noisy. When I zoom in, I see that just 3 out of 16 bits are used. I created a squarewave tone that is just 1 bit high, and I can still hear it! For most uses, this is not a big problem (audiophiles will disagree!), as I just have more noise than usual (about the same as old 8 bit hardware), but I'm also in the process of programming a hearing test program, in which case this problem is a death blow as the test subjects will even hear tones at the bottom of the theoretical range (lowering the windows volume is futile, see above) (I cannot update drivers, as Dell has discontinued XP support for my model)

  Read the article

• How can I avoid my web browser from redirecting to localhost using WAMP in Windows7?

  - by Josh

  I'm currently using Windows 7 with WAMP to try and work on some software, but my web browsers will not accept cookies from the "localhost" domain. I tried creating a few bogus domains in my hosts file by pointing them to 127.0.0.1 but when I type them in I am automatically redirected back to localhost. I have also configured virtualhosts in apache to correspond with the domains I added to the hosts file and it still redirects back to localhost. Is there anything special I must do on Windows 7 to get around this localhost redirect? Thanks for looking :) I'll include my host file here: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost 127.0.0.1 magento.localhost.com www.localhost.com Thanks for looking :)

  Read the article

< Previous Page | 829 830 831 832 833 834 835 836 837 838 839 840  | Next Page >