Search Results

Search found 18243 results on 730 pages for 'tcp connection'.

Page 84/730 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• Setting up a VPN connection to Amazon VPC - routing

  - by Keeno

  I am having some real issues setting up a VPN between out office and AWS VPC. The "tunnels" appear to be up, however I don't know if they are configured correctly. The device I am using is a Netgear VPN Firewall - FVS336GV2 If you see in the attached config downloaded from VPC (#3 Tunnel Interface Configuration), it gives me some "inside" addresses for the tunnel. When setting up the IPsec tunnels do I use the inside tunnel IP's (e.g. 169.254.254.2/30) or do I use my internal network subnet (10.1.1.0/24) I have tried both, when I tried the local network (10.1.1.x) the tracert stops at the router. When I tried with the "inside" ips, the tracert to the amazon VPC (10.0.0.x) goes out over the internet. this all leads me to the next question, for this router, how do I set up stage #4, the static next hop? What are these seemingly random "inside" addresses and where did amazon generate them from? 169.254.254.x seems odd? With a device like this, is the VPN behind the firewall? I have tweaked any IP addresses below so that they are not "real". I am fully aware, this is probably badly worded. Please if there is any further info/screenshots that will help, let me know. Amazon Web Services Virtual Private Cloud IPSec Tunnel #1 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Your Customer Gateway must be configured with a tunnel interface that is associated with the IPSec tunnel. All traffic transmitted to the tunnel interface is encrypted and transmitted to the Virtual Private Gateway. The Customer Gateway and Virtual Private Gateway each have two addresses that relate to this IPSec tunnel. Each contains an outside address, upon which encrypted traffic is exchanged. Each also contain an inside address associated with the tunnel interface. The Customer Gateway outside IP address was provided when the Customer Gateway was created. Changing the IP address requires the creation of a new Customer Gateway. The Customer Gateway inside IP address should be configured on your tunnel interface. Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.42 Inside IP Addresses - Customer Gateway : 169.254.254.2/30 - Virtual Private Gateway : 169.254.254.1/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: To route traffic between your internal network and your VPC, you will need a static route added to your router. Static Route Configuration Options: - Next hop : 169.254.254.1 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. IPSec Tunnel #2 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.46 Inside IP Addresses - Customer Gateway : 169.254.254.6/30 - Virtual Private Gateway : 169.254.254.5/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: Static Route Configuration Options: - Next hop : 169.254.254.5 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. EDIT #1 After writing this post, I continued to fiddle and something started to work, just not very reliably. The local IPs to use when setting up the tunnels where indeed my network subnets. Which further confuses me over what these "inside" IP addresses are for. The problem is, results are not consistent what so ever. I can "sometimes" ping, I can "sometimes" RDP using the VPN. Sometimes, Tunnel 1 or Tunnel 2 can be up or down. When I came back into work today, Tunnel 1 was down, so I deleted it and re-created it from scratch. Now I cant ping anything, but Amazon AND the router are telling me tunnel 1/2 are fine. I guess the router/vpn hardware I have just isnt up to the job..... EDIT #2 Now Tunnel 1 is up, Tunnel 2 is down (I didn't change any settings) and I can ping/rdp again. EDIT #3 Screenshot of route table that the router has built up. Current state (tunnel 1 still up and going string, 2 is still down and wont re-connect)

  Read the article

• Why would the Default Gateway constantly require resetting?

  - by Raven Dreamer

  I've had a (mostly) steady internet connection for the past two months. For the last hour, however, my connectivity has been dropping every 10 minutes or so, and must be reset. So far, I've always been able to fix the issue by running Windows network diagnostics (On Windows 7 64 bit), but the lack of constant internet is making it a pain to try and stream video, download games through steam, etc. Windows always reports a fix by "Resetting the Local Area Connector", telling me: Default Gateway Not Available. What's going on? Is the trouble on my end, or with my ISP? (Timewarner Cable) Things I've Tried: Reinstalling the motherboard's LAN drivers Manually setting a default gateway (gets cleared, reverts to default settings) Unplugged (Hard Reset) the router Unplugged / replugged ethernet cable.

  Read the article

• Website pages very slow to load on first access

  - by Merianos Nikos

  I have a production web server that makes sites to be very slow when load for first time. After the first time all connections are normal and fast. In the following screen you can see the first test I have run for a random site in my server: and here you can see the result of the second time request: As you can see there is a big change in the second load of the same page. Here is the page load time graph: My problem is that I don't really know anything about Red Had Linux server, and also I don't know where can I start. Can somebody to help me ? I like to find out the solution for the long time "wait" in connection. I know that my question is very minimal, but you can always ask me to give you information about the server.

  Read the article

• Our wi-fi at work is ridiculously slow, will adding more range extenders improve it?

  - by john

  At work, we have two wireless networks (e.g., Work1 Work2); the Work2 is used downstairs and Work1 is used upstairs. However, both are notoriously slow. The connection is better when we are wired in, but unfortunately due to our building being very old and our company growing very fast, most employees are not seated near the walls where the ethernet cables are. I had Cox, our ISP, run a bandwidth utilization test and it doesn't seem like we are capping out on upstream/downstream, which leads me to believe that it's strictly an issue with the wireless networks (which were implemented before I got there). The wireless networks are both Apple Airport Extremes. Is there anything I can do to improve the situation for everyone? Speeds are extremely slow, and sometimes drops out.

  Read the article

• Why can't I install apps on Windows 8 using specific dial-up modem connections?

  - by Vincent of Earth

  This problem has persisted since I first tried out Windows 8 Consumer Preview, and also affects Windows 8, Windows 8.1 Preview, and Windows 8.1. Specifically, the problem occurs when I try to install apps from the Windows Store on a Globe Tattoo Broadband or Smart Bro dial-up connection (two common ways of connecting to the internet in the Philippines). I can confirm that this isn't a problem with my copy of Windows or my Microsoft account because I was able to install any app on other connections like public WiFi. This problem has persisted on three different dongles and two different computers. So why can't I install apps on those two specific types of connections?

  Read the article

• NGINX + PHP FPM connect() failed (110: Connection timed out) while connecting to upstream

  - by Leonard Teo

  We're running a fairly large site using nginx and PHP-FPM and we're getting a lot of errors as the site load is quite high. We're getting "connect() failed (110: Connection timed out) while connecting to upstream"...upstream: "fastcgi://127.0.0.1:9000" Here's my config file for PHP-FPM. PHP-FPM: [www] listen = 127.0.0.1:9000 listen.allowed_clients = 127.0.0.1 user = nginx group = nginx pm = dynamic pm.max_children = 100 pm.start_servers = 20 pm.min_spare_servers = 5 pm.max_spare_servers = 35 pm.max_requests = 100 slowlog = /var/log/php-fpm/www-slow.log php_admin_value[error_log] = /var/log/php-fpm/www-error.log php_admin_flag[log_errors] = on What's the recommended config/number of servers/children for a high traffic site? We tried using Unix Sockets instead of TCP and got no noticeable improvements. Right now the errors are: connect() to unix:/var/run/php-fcgi.sock failed (11: Resource temporarily unavailable) while connecting to upstream...upstream: "fastcgi://unix:/var/run/php-fcgi.sock:"... Thanks, Leonard

  Read the article

• Predictive vs Least Connection Load Balancing Techniques

  - by Mani

  I have a windows based desktop application that communicates via TCP to the application servers. (windows 2003). No sticky sessions between client calls. We have exactly 2 servers to load balance and we are thinking to use a F5 hardware NLB. The application is a heavy load types, doing not much bussiness logic in the services but retrieving quite a big amount of data at most of the times. May be on an average 5000 to 10000 records at all times. Used mainly for storing and retirieving data and no special processing of data or calculations running on the server side. I am favouring 'predictive' considering my services take a while at times to return data and hence tracking the feedback would yield some better routing as in predictive. I am not sure if the given data is sufficient enough to suggest some ideas but considering these, what would be some suggestions\things to consider\best between Predictive and Least Connections ? Thanks.

  Read the article

• my windows xp sp3 diagnostick:windows could not detect any wired or wireless network cards installed on your machine

  - by Yosef

  Problem: cant connect to internet with my new installation of windows xp sp3. Details: I have ubuntu in pc that worked with wired internet. i format all disk and install windows xp sp3. i have auto internet that defined in my router - other computers have internet. I run diagnoze of ie and get: windows could not detect any wired or wireless network cards installed on your machine In Device Manager i have only 1394 Adapter I dont see any internet adapters. Edit: I find with ubuntu livecd that i have hardware:82566dc gigabit network connection Thanks

  Read the article

• What would be the total expenses of running an in-home web server?

  - by techaddict

  I have several hosting accounts with companies, and plan to keep them. However, I would like to try my hand at creating my own home web-server, both for fun and for the learning experience. I would like to know the expenses involved, including: electricity costs (greater than light bulb?) internet costs (will I have to upgrade my internet? Or is 3-5Mbps upload speed fine for a web server with medium amount of traffic? Would I have to get a separate internet connection?) other unknown expenses Consider that I will configure the web server myself, so that is not an expense. Also consider that I already have a computer (year-old Dell laptop, 15R) to use to be dedicated as the web server.

  Read the article

• How to configure a wireless router to point to a remote www proxy

  - by Mark

  I have a LG smart Tv with browser. I need the tv browser to connect to a uk based proxy server on port 808. Unfortunately there is no option within tv to setup proxy for its browser. Now the Tv connects via a wireless connection to the internet. IE: TV <- D-Link DIR-605L <- ADSL <- WWW. Is it possible to setup this wireless router to connect the TV to the Proxy ?? If so ? where ? and what setings do i need to change in the wireless router ?? In short my question is ? How do i get the wireless router to make up for the lack of proxy connectivity within my Tv browser ?? Thanks in advance NB: I have configured my Pc's browser's proxy settings, and streaming via the proxy works 100%

  Read the article

• Connection drops while transferring large files to one server on a network

  - by Charlotte

  My company has two sites, each with their own LAN, using site to site VPN tunnel to connect the two sites. When transferring files (especially larger files) from site1 to site2 server1, the file transfer fails. I don't think this can be a VPN issue because transferring the same files to site2 server2 which is on the same network as server1 works fine. Pings to server1 and server2 at site2 from site1 are about the same, mostly 19/20ms with the odd one up to 50ms. As server1 is DB server with a high load I thought the NIC maybe overloaded, but a transfer from site2 server1 to site2 server2 works fine, and that uses the same NIC on server1 as transfers from site1 to site2 server1. The servers are both Windows Server 2003 VMs with VMXNET 3 NICs. Site2 Server1 route print: IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 28 9b ...... vmxnet3 Ethernet Adapter #2 0x10004 ...00 50 56 99 18 97 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.18 10 10.10.10.0 255.255.255.0 10.10.10.70 10.10.10.70 10 10.10.10.70 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.18 172.20.10.18 10 172.20.10.18 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.18 172.20.10.18 10 224.0.0.0 240.0.0.0 10.10.10.70 10.10.10.70 10 224.0.0.0 240.0.0.0 172.20.10.18 172.20.10.18 10 255.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 1 255.255.255.255 255.255.255.255 172.20.10.18 172.20.10.18 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site2 Server2 route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 15 00 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.114 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.114 172.20.10.114 10 172.20.10.114 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.114 172.20.10.114 10 224.0.0.0 240.0.0.0 172.20.10.114 172.20.10.114 10 255.255.255.255 255.255.255.255 172.20.10.114 172.20.10.114 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site1 Server route print: =========================================================================== Interface List 14...00 50 56 93 00 0b ......vmxnet3 Ethernet Adapter #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.168.1 192.168.168.118 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.168.0 255.255.255.0 On-link 192.168.168.118 261 192.168.168.118 255.255.255.255 On-link 192.168.168.118 261 192.168.168.255 255.255.255.255 On-link 192.168.168.118 261 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.168.118 261 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.168.118 261 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.168.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 261 fe80::/64 On-link 14 261 fe80::3c6b:996f:ef36:ee76/128 On-link 1 306 ff00::/8 On-link 14 261 ff00::/8 On-link =========================================================================== Persistent Routes: None tracert from site1 to site2 server1: Tracing route to server1 [172.20.10.18] over a maximum of 30 hops: 1 19 ms 19 ms 19 ms server1 [172.20.10.18] Trace complete. tracert from site2 server1 to site1: When this was run it went to the external IP of site2, then to a couple of external ips of the isp, then times out. Can anyone suggest any troubleshooting steps? Thanks, Charlotte.

  Read the article

• Switch computer off automatically when the internet is disconnected

  - by Vin

  Is there any free software that will detect the status of internet and shutdown the system when the internet disconnects? Or (more generally) can something run a task when the internet disconnects, and I can route it to shutdown the machine? I am downloading things overnight. But my problem is that sometimes the internet connection will be disconnected in the middle of the night, so there is no point in keeping the system running the rest of the night. So I need to avoid this problem by detecting the net connectivity.

  Read the article

• not able to mount media to ESX 4.0

  - by jack8138

  Hi, I have ESX 4.0 running on NEC Express 5800 R-120a model. I have 2 VMs running windows XP. I am not able to mount any media to it. When I try connecting the local media to the VM, the error message comes mentioning "a connection to the host could not be established.: I have checked and there is no network issue. ESX is accessible fine. Any help would be greatly appreciated. Besides, I have opened almost all the ports in the firewall just to make sure there is no port conflict.

  Read the article

• Remote connection to SQL server doesn't use the instance name

  - by Max

  I have a web server with SQL express 2008 installed. I was trying to connect to this from my local machine using SSMS. After enabling TCP/IP in SQL configuration manager, starting SQL browser service and opening up the firewall I still couldn't connect using xxx.xxx.xxx.xxx\sqlexpress as the server name. Finally out of frustration I tried to connect taking off the sqlexpress instance name to just xxx.xxx.xxx.xxx and it worked! I'm really at a loss here as to why this works. What would happen if I installed more instances of SQL?

  Read the article

• Access Other Computer via ADSL Modem and Router

  - by Sohail

  My network configuration is like this ISP - Modem - Router - Computer and the same goes for my friend. We want to share large files or to access each other's computer. The Passwords to login to the web page of each other modems are known. I mean, we can access each other Modem Web GUI easily ( because we know the WAN IP of each other modem ). The question is how do i access his or how do he access my computer? Is there any way to do so. Remote desktop connection is not working :( Please help

  Read the article

• SQL Server 2008 CPU usage goes to 100% - troubleshooting help needed?

  - by Ali

  I have a fairly powerful database server having SQL Server 2008 R2 installed. There is only one database on it which is being accessed from 2 servers (around 5/6 applications). The problem is as soon as applications start pointing to the database, system's CPU usage goes upto 100% with sqlserver itself using 95+%. I have checked profiler, there aren't any heavy queries running there. I have checked active connections, they are hardly 150. Still CPU usage is around 100% and applications are experiencing slow response/connection to database server are getting refused. Database grus, I really need some ideas here. Thanks.

  Read the article

• DSL vs Cable latency

  - by tovmeod

  currently I have a 10Mbps DSL line and I'm thinking to switch to a cable since they got 100Mbps for a little less than double the price I'm paying for 10Mbps. In other words the cable company is offering 100Mbps for the price of 20Mbps DSL. Since 10Mbps is more than enough for me I am worried about the latency, I saw this that is just a guy experiment, that shows that cable and DSL are the same in practical terms, and this but I couldn't grasp it, not sure if it is helpful. So my question is if there's any practical difference between cable and DSL, mainly in latency terms but I would be also interested in other advantages/disadvantages. This is for my home connection, I work from home but I don't run any server, I most of the time code, skype and eventually game.

  Read the article

• I can't do a Remote Assistance session to a Windows XP box from Windows 7.

  - by superkinhluan

  My Mom's computer is running Windows XP, and my desktop running Windows 7. She's having some technical issue, so I want to do a Remote Assistance session to her machine. However, no matter what I've tried, the Remote Assistance program doesn't connect successfully. I've verified that the Windows Firewall (on both my and her machines) is configured properly to allow Remote Assistance program to go through. What's interesting is that I have the same problem when I try to do Remote Assistance from my desktop to my laptop, which is also running Windows XP. However, when I try to connect to my girlfriend's machine, which is runninng Windows 7 this time, the connection is successful. So in the end, I guess there must be some incompability between Windows 7 and Windows XP. Does anyone experience the same issue? How did you resolve it?

  Read the article

• How to disable internet access at night on the router?

  - by izb

  I have an internet connection that I'd like to be enabled only during the day. With multiple household internet devices, this would need to be something disabled at the level of the router. I don't believe the router offers this sort of functionality, but I'm reasonably familiar with setting up web servers and the like, and I'm wondering if I can set up some sort of proxy server on the internet that the router must go through and have that proxy only active at certain times of day. It's a bit vague I know, but is something like this even possible? If not, are there other solutions to the problem?

  Read the article

• approx via inetd is not open to connection for others machines

  - by Cédric Girard

  I have an approx server to speed up Debian apt updates, on my Ubuntu 11.04 desktop PC, it had ran fine in the past, but today le 9999 port is open from localhost, but not for others PC. I have not modified inetd configuration at all. What can I check and try? inetd.conf 9999 stream tcp nowait approx /usr/sbin/approx /usr/sbin/approx approx.com # Here are some examples of remote repository mappings. # See http://www.debian.org/mirror/list for mirror sites. debian http://ftp2.fr.debian.org/debian security http://security.debian.org/debian-security volatile http://volatile.debian.org/debian-volatile # The following are the default parameter values, so there is # no need to uncomment them unless you want a different value. # See approx.conf(5) for details. $cache /espace/Dossiers/approx $max_rate unlimited $max_redirects 5 $user approx $group approx $syslog daemon $pdiffs true $offline false $max_wait 10 $verbose false $debug false I tried to allow others PC to connect with a "ALL: ALL" in hosts.allow. ufw is disabled, iptables-save is empty.

  Read the article

• Connect to development server via switch?

  - by letseatfood

  I apologize upfront if this isn't appropriate for superuser. I asked it on serverfault and was told it was too general for that site. I have a laptop with Vista and it receives it's internet connection wireless. I have an old desktop with Ubuntu 10.04 Server Edition installed and it is setup as a development server with Apache, MySQL, and PHP. This works well, with the server having a static IP address. The server is connected to the router via an Ethernet cable. Is it possible to disconnect the cable that is currently connecting the server and the router, then connect the server and workstation to a switch, so that I am still able to connect to the server via web browser from the workstation? I am trying to eliminate the long ethernet cable connecting the server to the router in the other room. I already have a switch, that is why I asked specifically about it. Thanks and I will be more than happy to clarify!

  Read the article

• Plesk 10 port 8443 connection timeout

  - by GriffinHeart

  I've installed plesk 10 on centOS and after installing to access the cp you need to go https::8443 I'm not being able to, and would like to find out why i can ssh to the server and i can, from the server telnet, to those ports. from another machine i can ping it but when i try to telnet or go to that address i get connection timeout, happens with port 80 and 8443 from my netstat netstat -nlp | grep 8443 tcp 0 0 :::8443 :::* LISTEN 25205/sw-cp-serverd How do i find out whats causing the problem? I also have a router but firewall is at the minimum and the server configured as DMZ, also tried to redirect 8443 to 8443 of the server.

  Read the article

• iPhone always assigned wrong ip

  - by Ashley Ray

  for some reason most of the time my iPhone connects to the home network the ip address seems wrongly assigned as it 'loses connection' even even with strong reception. If I change the ip address to a static from 168.2.10 to 168.2.15 works fine until it appears to renew back to the prior. I am using a power-plug extender from the modem to router. Then have a laptop Printer playstation tv and another iPhone that always connect fine. The modem also has a crappy wireless which I haven't connected any devices to. I'm sure the forum will have a simple answer!

  Read the article

• Plesk 10 port 8443 connection timeout

  - by GriffinHeart

  I've installed plesk 10 on centOS and after installing to access the cp you need to go https::8443 I'm not being able to, and would like to find out why i can ssh to the server and i can, from the server telnet, to those ports. from another machine i can ping it but when i try to telnet or go to that address i get connection timeout, happens with port 80 and 8443 from my netstat netstat -nlp | grep 8443 tcp 0 0 :::8443 :::* LISTEN 25205/sw-cp-serverd How do i find out whats causing the problem? I also have a router but firewall is at the minimum and the server configured as DMZ, also tried to redirect 8443 to 8443 of the server.

  Read the article

• web browser not opening

  - by Hoss7811

  I had a virus adware on my desktop. I cleaned it using AVG. Now no browser will open, though the Internet connection is fine. When trying to open any browser I get a dialog box that says it can't find that location. This happens to all my browsers. I even downloaded firefox on my laptop and installed it on the desktop and still get the same response - Windows can't find the location. This all started when opening an email. I'm running Windows Vista

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >