Search Results

Search found 22912 results on 917 pages for 'hosted service'.

Page 865/917 | < Previous Page | 861 862 863 864 865 866 867 868 869 870 871 872  | Next Page >

• Issue with Netgear GS108T Managed Switch and Jumbo Frames

  - by Richie086

  I recently purchased a Netgear GS108T managed switch and I am trying to configure jumbo packets between my NAS (Thecus N4100Pro), PC and managed switch. I should mention the fact that I was able to use jumbo frames between my PC and NAS before I purchased the switch without issue. My Desktop has a wired gigabit NIC (Intel 82579V Gigabit) and has the ability to configure jumbo frames (see pic) that are either 9014 bytes or 4088 bytes. I choose 9014 bytes for the jumbo frame size My NAS supports jumbo frames as well, and is configured to use 9014 as the frame size. When I go into my Netgear managed switch and set the frame size to 9014 on the ports I am using for my PC and NAS. See image As soon as I hit apply in the web interface, I loose my connection to the SMB shares on my NAS and I can no longer connect to the web admin interface for my NAS. The really strange thing is I can ping my NAS via the ping command, but when I try to connect to the web interface on port 80 or port 443 the page never loads. I did a scan from my PC to my NAS using nmap and I can see the following ports open PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 631/tcp open ipp 2000/tcp open cisco-sccp 2049/tcp open nfs 3260/tcp open iscsi 49152/tcp open unknown MAC Address: 00:14:FD:15:00:44 (Thecus Technology) Read data files from: C:\Program Files (x86)\Nmap Nmap done: 1 IP address (1 host up) scanned in 211.97 seconds Raw packets sent: 1 (28B) | Rcvd: 1 (28B) Anyone have any idea what is going on here? Why is nmap able to detect the ports are open and listening for http, https and file sharing but I cant connect when all devices have jumbo packets enabled? Stranger still - I did a packet capture using wireshark while the nmap scan was running and filtered so I only saw converstations between my PC and my NAS. Here are the packet details from my scan Only 4 packets over 5k bytes? What is going on here? Do I not need to configure jumbo frame sizes on the switch? I have an internet connection from my pc to the switch to my router - I just cannot connect to my NAS. I just checked on my iPhone and I am able to open my NAS web admin interface without issue on my iPhone! WTF!!!!!! Let me know if you need more details..

  Read the article

• Scientific Linux - mysql and apachefail to start on reboot

  - by Derek Deed

  Both mysqld and httpd fail to restart following a reboot of the server, although chkconfig --list shows both daemons set to on for run levels 2,3,4 & 5 All control is being exectuted via Webmin Reboot server – MySQl and Apache not running MySQL Database Server MySQL version 5.1.69 MySQL is not running on your system - database list could not be retrieved. Click this button to start the MySQL database server on your system with the command /etc/rc.d/init.d/mysqld start. This Webmin module cannot administer the database until it is started. Apache Webserver Apache version 2.2.15 Start Apache Search Docs.. Global configuration Existing virtual hosts Create virtual host Select all. | Invert selection. Default Server Defines the default settings for all other virtual servers, and processes any unhandled requests. Address Any Port Any Server Name Automatic Document Root /var/www/drupal Virtual Server Processes all requests on port 443 not handled by other virtual servers. Address Any Port 443 Server Name Automatic Document Root /var/www/drupal Select all. | Invert selection. chkconfig --list mysqld mysqld 0:off 1:off 2:on 3:on 4:on 5:on 6:off chkconfig --list httpd httpd 0:off 1:off 2:on 3:on 4:on 5:on 6:off Manually Restart Apache chkconfig --list httpd httpd 0:off 1:off 2:on 3:on 4:on 5:on 6:off Manually Restart MySQL chkconfig --list mysqld mysqld 0:off 1:off 2:on 3:on 4:on 5:on 6:off Everything now running okay; but no difference in the chkconfig outputs above. Set chkconfig --levels 235 httpd on /etc/init.d/httpd start The same for mysqld but no change in operation. Log files show that the shutdown has been completed successfully; but there is no indication of the service restarting until it is executed manually: 131112 13:59:15 InnoDB: Starting shutdown... 131112 13:59:16 InnoDB: Shutdown completed; log sequence number 0 881747021 131112 13:59:16 [Note] /usr/libexec/mysqld: Shutdown complete 131112 13:59:16 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended 131112 14:09:52 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 131112 14:09:52 InnoDB: Initializing buffer pool, size = 8.0M 131112 14:09:52 InnoDB: Completed initialization of buffer pool [Tue Nov 12 13:59:13 2013] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Tue Nov 12 13:59:13 2013] [notice] Digest: generating secret for digest authentication ... [Tue Nov 12 13:59:13 2013] [notice] Digest: done [Tue Nov 12 13:59:14 2013] [notice] Apache/2.2.15 (Unix) DAV/2 PHP/5.3.3 mod_ssl/2.2.15 OpenSSL/1.0.0-fips configured -- resuming normal operations [Tue Nov 12 13:59:14 2013] [notice] caught SIGTERM, shutting down [Tue Nov 12 14:27:13 2013] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Tue Nov 12 14:27:13 2013] [notice] Digest: generating secret for digest authentication ... [Tue Nov 12 14:27:13 2013] [notice] Digest: done [Tue Nov 12 14:27:13 2013] [notice] Apache/2.2.15 (Unix) DAV/2 PHP/5.3.3 mod_ssl/2.2.15 OpenSSL/1.0.0-fips configured -- resuming normal operations Is anyone able to shed any light on this problem, Cheers, Derek.

  Read the article

• Uninstall php and nginx or fix setup

  - by jreed121

  First off, I'm a huge linux noob - sorry... I'm trying to setup nginx with php-fpm on debian and I'm pretty sure that I've completely screwed it up. nginx seems to be running fine because I can it it from a web browser and it load the stock "Welcome to nginx!" page. I'm not so sure about php-fpm though. When I try something like # restart php-fpm I get: bash: restart: command not found First off php-fpm some how got installed as php5-fpm when I do root@server:/etc/init.d# ls, which seems to contradict every tutorial and help doc I've read (supposed to be 'php-fpm'). I can restart it with this: service php5-fpm restart And just enter the package name 'php5-fpm' I get this: root@server:~# php5-fpm [17-Nov-2012 23:15:36] NOTICE: PHP message: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20100525/suhosin.so' - /usr/lib/php5/20100525/suhosin.so: cannot open shared object file: No such file or directory in Unknown on line 0 [17-Nov-2012 23:15:36] ERROR: An another FPM instance seems to already listen on /var/run/php5-fpm.sock [17-Nov-2012 23:15:36] ERROR: FPM initialization failed The root for nginx is /usr/share/nginx/html, when I try to navigate to a .php file in there with my web browser, it tries to download the file instead of interpret it. I would like this folder to be in my user's home directory ie: /home/administrator/www or /home/nginx/www. I know in order to do this I need to modify nginx.conf, but I find that configuration file difficult to understand. I suppose the fact that my .php scripts aren't being handled is my bigger problem anyways. When I try to see what running on port 9000 (php-fpm default port) with lsof -i :9000 it returns nothing - I guess indicating that it isn't listening. then I head over to vim /etc/php5/fpm/php-fpm.conf and there is no where to designate a port number. So should I just uninstall everything and start from scratch? If so, how do I clean it all up? Any suggestions for a tutorial once I'm ready to try again? Should I attempt to troubleshoot this mess? If so where should I start? Sorry guys, I'm feeling pretty stupid and lost right now. I'm not sure what my next steps are in trying to resolve this issue are. I realize that this is a horrible question for this type of Q&A site, but I'd really appreciate any guidance.

  Read the article

• Installing OpenLDAP on Fedora 12: ldap_bind: Invalid credentials (49)

  - by Alpha Hydrae

  I've been trying to set up the OpenLDAP installed by default on Fedora 12, very unsuccessfully. My ultimate goal is to use LDAP authentication for user login and Apache, using the OpenLDAP server running on the same machine. The server is running, but the error I always get when I try to use ldapsearch or ldapadd is: ldap_bind: Invalid credentials (49) I've been following these tutorials, but none of them helped me: http://www.howtoforge.com/openldap_fedora7 http://www.redhat.com/docs/manuals/linux/RHL-9-Manual/ref-guide/s1-ldap-quickstart.html http://www.howtoforge.com/linux_ldap_authentication http://docs.fedoraproject.org/deployment-guide/f12/en-US/html/s1-ldap-pam.html http://www.openldap.org/doc/admin24/quickstart.html First, some components were already installed, and I installed these with yum: yum install openldap-servers openldap-devel Then, I created a basic slapd.conf file in /etc/openldap: database bdb suffix "dc=sniejana-sandbox,dc=com" rootdn "cn=root,dc=sniejana-sandbox,dc=com" rootpw {SSHA}cxdz55ygPu4T3ykg7dgu+L0VRvsFSeom directory /var/lib/ldap/sniejana-sandbox.com I obtained the rootpw with this command: slappasswd -s changeme I also created the /var/lib/ldap/sniejana-sandbox.com directory and made sure the entire contents of /var/lib/ldap were owned by the ldap user. I found two ldap.conf files, one in /etc and one in /etc/openldap. I don't know which is the right one. If I understood correctly, this file is to configure the client. I put this in both: HOST localhost BASE dc=sniejana-sandbox,dc=com I then ran the server with: service slapd start It said OK. Most of the tutorials above say to use the command ldapsearch -D "cn=Manager,dc=my-domain,dc=com" -W to ensure that everything's working. When I execute this command, a password prompt appears, and after entering the password, I get the error. ldapsearch -D "cn=root,dc=sniejana-sandbox,dc=com" -W Enter LDAP password: ldap_bind: Invalid credentials (49) The same thing happens when trying to use ldapadd. I tried with an encrypted and unencrypted password in slapd.conf, it doesn't change anything. Adding a -x for simple authentication doesn't change anything either. netstat -ap confirms the server is listening: tcp 0 0 *:ldap *:* LISTEN 4148/slapd tcp 0 0 *:ldap *:* LISTEN 4148/slapd ps -ef|grep slapd confirms the process is running: ldap 4148 1 0 15:22 ? 00:00:00 /usr/sbin/slapd -h ldap:/// -u ldap Running slaptest procudes config file testing succeeded. I read somewhere that the command ldapsearch -x -b '' -s base '(objectclass=*)' namingContext can confirm the server is running. It appears to work: # extended LDIF # # LDAPv3 # base <> with scope baseObject # filter: (objectclass=*) # requesting: namingContext # # dn: # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 I'm running out of ideas. Am I missing something obvious?

  Read the article

• OpenVPN, Great on Windows, VERY slow on Mac...

  - by Phsion

  Hello, I'm not really an IT Pro, but this seemed like the best place to ask this question... I have setup VPN networks in the past, for fun, and everything was great, but now I've set one up for my boss, and while my computers all work great, his Mac machines are almost too slow to work with. Its pretty much vanilla configs all around, anyone have any ideas? Its a TUN routing setup over UDP. Back Story: My boss travels a lot, and wants to be able to access all his files from the road, and is also pretty paranoid about security (even though knows almost nothing about computers). SO i figured a VPN would be the answer. I went with OpenVPN, but there are some other issues. The only ISP we can get in our area besides Dial-UP is a crappy Satellite provider, that doesn't offer public IPs unless your willing to pay, so while the computers and VPN setup are pretty vanilla, the routing and structure is strange to get around this limitation. Specs: Its OpenVPN2, and there are six machines using it (only three actually use it, the rest are my test machines), one Windows 7 laptop, two XP Desktops, one OS X 10.5 Desktop, one 10.6 Desktop, and one 10.6 Laptop. One XP Desktop sits at my house and acts as the server (6Mbs/2Mbs FIOS connection). One XP desktop sits at the office and hosts a webpage that will wake up the Main Mac Desktop from sleep, and also ping all the machines on the VPN and show their status. The main office mac (10.6) stays in sleep mode until it gets the Wake-On-Lan packet from the Office XP, and then it auto connects to the VPN and opens itself up. The reason for all this is the Satellite private IP crap means i cant directly access the office machines outside of the LAN, so everyone connects to my house first, then they talk to each other from there. The Wake On Lan weirdness is because my boss doesn't want to leave the main Mac on all the time, and making a quick and dirty webpage was the easiest way to send a Magic Packet from inside the LAN without confusing my boss. The VPN uses Client Config files to make static IPs for the client. The only thing i found in google was some changes to the VPN MTU settings (down to 1400) but no real help. Oh, and i forgot...all the windows machines just have OpenVPN start as a service. The Mac laptop uses tunnelblick (an OpenVPN GUI) and the Mac Desktops use OpenVPN in normal command line mode. Server Config: tun-mtu 1500 fragment 1450 mssfix 1450 management localhost #### port #### proto udp dev tun ca ####### cert ####### key ###### dh ###### server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt client-config-dir ccd route 10.8.0.0 255.255.255.252 client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status log Client Configs (all are simple variations on this) tun-mtu 1500 fragment 1450 mssfix 1450 client dev tun proto udp remote ######## #### resolv-retry infinite nobind persist-key presist-tun ca ##### cert ##### key ##### ns-cert-type server comp-lzo verb 3

  Read the article

• What "pieces" are needed in order to set up a cluster of physical servers?

  - by Chris Dutrow

  Background: Currently, we use Rackspace cloud servers. We have no intention to stop using them, but would like to look into setting up a cluster of physical servers (probably desktop computers in the $400 range with 8gb memory each) to offset some of our load and work as a secondary, more powerful, less reliable system. To put things in perspective, we can buy comparable desktop computers for the same price as we pay in one month to rent them on Rackspace Cloud. I understand that this is generally a dumb idea. However, in this particular instance, the server cluster is needed for its computation power. It is not mission-critical, it does not host a consumer-facing website, and if it goes down for a day or two, its not really a problem. Currently, we have access to business class verizon fios. If I understand correctly, we can get at least 25 dedicated IP addresses with this service, this should be enough. Requirements: Each server runs Linux Centos 6.3 Some of the servers run Python and execute processes from a task queue (Redis or RabbitMQ) Some of the servers are capable of serving static files and Python driven REST APIs Some of the servers host a Cassandra database cluster One or more of the servers are a Redis database servers One or more of the servers are PostgreSQL servers Questions: What kind of router or switch is needed? We would like the computers to be able to communicate effectively with each other via internal IP addresses. This is especially important for communicating with servers hosting Redis that need to be able to respond to requests very quickly. Are there special switches or routers that need to be used to connect the servers together? Are Desktop computers ok for this? We have found that we are mostly RAM-bottle necked, I understand that some servers have highly superior CPUs, but I'm not sure we need CPU power as much as we need RAM, which is cheap in Desktop computers. Will we have problems with the WIFI cards in the desktops or any other unexpected hardware limitation? What tools should be used to "image" the servers. For example, when we get an installation right for a Redis server or Cassandra node, are there tools that come with Linux Centos 6.3 to image the server to a USB drive or something like that? Or do we need to use some other software for this? What other things are we missing that we should be concerned about? Thanks so much!

  Read the article

• Issues connection to Ubuntu via PuTTy

  - by user1787262

  I'm not sure this is the appropriate stack exchange site to post this question on. If not, please flag this for migration. I am trying to use PuTTy ssh into my ubuntu machine which is wirelessly connected to the same network. I originally ran ifconfig to get my ubuntu machines private network IP address. I then verified that ssh was running, I even ssh'd into my school network and then into the ubuntu machine itself. No problems yet. On my windows 8 machine I ran ipconfig to get my private network IPv4 address. I then pinged my ubunty machines IP and 100% of packets were received. I figured, "OK we are ready to use PuTTy to connect to my Ubuntu Machine". Keep in mind this was my first time using PuTTy. I tried entering the IP of my ubuntu machine in the PuTTy Config GUI but I got a connection timeout. At this moment I don't really know what's going on, SSH is running on port 22 of my Ubuntu machine and I can ping the machine why is it not connecting? (I tried [username]@ip too). So I went on my Ubuntu machine and ran nmap -sP 192.168.0.1/24 and found that my windows machines IP did not show up, the host is down. I'm at a lost in something I am not very familiar with. Would anyone be able to help me or direct me to some resources that would trouble shoot my problem? Thank you EDIT (ADDITION): tyler@tyler-Aspire-5250:~$ nmap -v 192.168.0.123 Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 01:56 MDT Initiating Ping Scan at 01:56 Scanning 192.168.0.123 [2 ports] Completed Ping Scan at 01:56, 3.00s elapsed (1 total hosts) Nmap scan report for 192.168.0.123 [host down] Read data files from: /usr/bin/../share/nmap Note: Host seems down. If it is really up, but blocking our ping probes, try -Pn Nmap done: 1 IP address (0 hosts up) scanned in 3.14 seconds tyler@tyler-Aspire-5250:~$ nmap -Pn 192.168.0.123 Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 01:56 MDT Nmap scan report for 192.168.0.123 Host is up (0.022s latency). Not shown: 998 filtered ports PORT STATE SERVICE 2869/tcp open icslap 5357/tcp open wsdapi Nmap done: 1 IP address (1 host up) scanned in 72.51 seconds

  Read the article

• Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem

  - by zchads

  Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem. Hardware Information: Buffalo Wireless Router/access point, Model: WZR-HP-G300NH-AP DSL Modem: Generic (actually not sure of manufacture). Service Provider: TOT (Thailand) Laptop-1: Windows XP and Belkin PCMIA Network Card Laptop-2: Windows XP unknown network card & Wifi Laptop-3: Windows 7 unknown network card & Wifi Outline of Problem/actions taken: After a recent power failure the router and laptop-1 connected to router were no longer able to access the internet. Actions taken to try and recover internet access: Using Laptop-1 tried to configure Router with PPPoe settings using software from Router Manufacture. During the installation process a Timeout error was experienced, unable to connect to WAN. Used Internet Explorer to communicate directly with Router using IP address. Changed settings to use PPPoe settings given by ISP. Router was not able to communicate with Internet. Repeated steps 1-4 again with no success. Reset Router and DSL modem. Repeated steps 1-4 again still no success. Tried connecting Laptop-1 directly to DSL to gain access to internet to research problem. No Network connection with DSL could be established…connection would be established for a second and then be lost and didn’t appear long enough to actually connect to DSL. Replugged LAN back into Router and connection was regained with laptop-1. Replugged Laptop-1 directly into DSL and again unable to establish network connection. Uninstalled network card and all of its drivers on Laptop-1. Reinstalled network card and drivers and tried connecting directly to DSL. Still unable to make network connection. Plugged DSL into Laptop-3 and Internet connection was established. Being Laptop-3 does not have a CD-Rom, Laptop-2 was tried to connect to the router. With Laptop-2 steps 1-7 ended up being repeated without success. Tried plugging Laptop-2 directly into DSL and again no network connection could be established. Using Laptop-3 with a direct connection to DSL downloaded latest Router FW. Installed router FW using Laptop-1. Tired the installation process again without success. Being desperate reinstalled OS on Laptop-1 still not success. Tried using “ipconfig” with router to see what was going on without success. With laptop-1 connected to DSL went through the “ipconfig /…” inputs to see if anything made a difference. Being the network card was not able to make a connection this provide very little information “media disconnected”. So now I have a router and two laptops which are unable to connect to the internet and sure could use some advice/help.

  Read the article

• How to have Windows Server DNS use hosts file to resolve specific host names

  - by user41079

  Hello, everyone, I'm facing a small problem with Windows Server 2003 DNS service. In my corporation, I'm running Microsoft DNS server(172.16.0.12) to do name resolution to my company intranet(domain name ends in dev.nls. resolving to IP 172.16..), and it is also configured as a DNS forwarder to forward other domain names(e.g. *.google.com , *.sf.net) to Internet real DNS servers. This internal DNS server never tends to serve users from outside world. And, we are running a mail server(serving incoming mail for a real Internet domain @nlscan.com) inside company firewall which can be accessed in either way: by connecting to 172.16.0.10 from within intranet. by connecting to mail.nlscan.com(resolved to 202.101.116.9) from Internet. Note that 172.16.0.10 and 202.101.116.9 is not the same physical machine. The 202 one is a firewall machine who do port forwarding of port 25 and 110 to intranet address 172.16.0.10 . Now my question: If users inside corporate LAN want to resolve mail.nlscan.com, it resolves to 202.101.116.9. That's correct and workable, BUT NOT GOOD, because the mail traffic goes to the firewall machine then bounces to 172.16.0.10 . I hope that our internal DNS server can intercept the name mail.nlscan.com and resolve it to 172.16.0.10 . So, I hope that I can write an entry in "hosts" file on 172.16.0.12 to do this. But, how can Microsoft DNS server recognize this "hosts" file? Maybe you suggest, why not have intranet user use 172.16.0.10 to access my mail server? I have to say it is inconvenient, suppose a user(employee) works on his laptop, daytime in office and nighttime at home. When he is at home, he cannot use 172.16.0.10 . Creating a zone for nlscan.com on our internal DNS server is not feasible, because the name server for nlscan.com domain is on our ISP, and it is responsible for resolving other host names and sub-domains under nlscan.com . Thank you in advance.

  Read the article

• What are some of the best wireless routers for a price-conscious home power-user?

  - by Alain

  I'm extremely dissatisfied with the 'popular' choice for routers in homes and small offices. They are expensive (upwards of 60$), lack a great deal of useful configuration options, and seem to need to be restarted quite often. (Linksys comes to mind). I've been on the market for a good router lately, and slowly collecting a set of requirements I feel good routers should meet. Maximum number of TCP/IP connections. - This isn't something I see any routers advertise, but in terms of supporting torrent applications, I've been screwed by routers that support less than 20 here. From what I understand a fairly standard number is 200, but there are not so expensive routers that support thousands. Router configuration menu - Most have standard menu's that let you set up basic things like your wireless network encryption settings, uPnP, and maybe even DMZ (demilitarized zones). An absolute requirement for me, however, are routers with good enough firmware to support: Explicit Port forwarding Assigning static local ips to specific mac addresses, or at least Port forwarding by MAC address Port, IP and MAC filtering Dynamic DNS service for home users who want to set up a server but have a dynamic IP Traffic shaping (ideally) - giving priority to packets from certain machines or over certain ports. Strong wireless signal - If getting a reliable signal requires me to be so close to the router that I can connect an Ethernet cable, it's not good enough. As many Ethernet ports as possible. - Because I want to be able to switch from console gaming to PC gaming without visiting my router. So far, the best thing I've stumbled upon (in the bargain bin at staples) was a 20$ retail plus router. It was meant to be the cheapest alternative until I could find something better to purchase online, but I was actually blown away by the firmware capabilities. It supports defining reserved bandwidth for certain network traffic, dynamic DNS, reserving local IPs for specific MAC addresses, etc. At 2 am when my roommate is killing our Internet with their torrents, I can limit their bandwidth without outright blacklisting them. I have, however, met serious limitations when it comes to network traffic between local machines. It claims a 300Mbps connection, but I have trouble streaming videos from my PC to my console or other laptops wirelessly. It has a meltdown and needs to be reset once in a while (no more than a couple times a month), and it's got a 200 connection limit. There 4 Ethernet ports in the back but I'm pretty sure the first doesn't work. So some great answers to this question would be: Any metrics you use to compare routers, and requirements you have for new candidates. The best routers you've found for supporting home servers, file management systems, high volume torrent traffic, good price/feature ratio, etc. Good configuration advice (aside from 'use Ethernet whenever possible') Thanks for your feedback and experiences!

  Read the article

• Virtual Machine with Bridged Adapter to Centos not accepting ssh from host machine [migrated]

  - by javadba

  I have a bridged connection on VirtualBox from os/x 10.8.5 host to Centos 5.8 client. But I suspect this is more of a general issue than specific to the host and precise version of linux. Shown below are the networking info from the VirtualBox and from within the guest sshd is running on port 22: [root@oracle-linux ~]# ps -ef | grep sshd | grep -v grep root 3103 1 0 20:22 ? 00:00:00 /usr/sbin/sshd root 14994 3103 0 21:23 ? 00:00:00 sshd: root@pts/1 Port 22 listening: [root@oracle-linux ~]# netstat -an | grep 22 | grep tcp | grep LIST tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2207 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2208 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN Here are ip addresses, still on the guest os: [root@oracle-linux ~]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b9:e5:79 brd ff:ff:ff:ff:ff:ff inet 10.0.15.100/24 brd 10.0.15.255 scope global eth0 inet6 fe80::a00:27ff:feb9:e579/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b4:86:8a brd ff:ff:ff:ff:ff:ff inet 10.0.3.15/24 brd 10.0.3.255 scope global eth1 inet6 fe80::a00:27ff:feb4:868a/64 scope link valid_lft forever preferred_lft forever [root@oracle-linux ~]# I can ssh to the guest from the guest: root@oracle-linux ~]# ssh 10.0.3.15 The authenticity of host '10.0.3.15 (10.0.3.15)' can't be established. RSA key fingerprint is ef:08:19:72:95:4d:e5:28:af:f3:6f:54:07:84:ba:04. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '10.0.3.15' (RSA) to the list of known hosts. [email protected]'s password: Last login: Mon Oct 21 21:24:12 2013 from 10.0.15.100 But can NOT ssh from the host to the guest: 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection Here is bridged connection infO; BTW I looked into other answers, and one of them mentioned doing service iptables stop That did not help. Adapter 2 is a NAT, shown below In case NAT is causing any issues, i shut it down and restarted networking. [root@oracle-linux ~]# /etc/init.d/network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: Still No joy.. 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection

  Read the article

• Certain SFTP user cannot connect

  - by trobrock

  I have my Ubuntu Server set up so users with the group of sftponly can connect with sftp, but have a shell of /bin/false, and they connect to their home directories. This is working fine with three of the user accounts I have. But I added a new user account today the same way that I added the others and it will not successfully connect. sftp -vvv user@hostname debug1: Next authentication method: password user@hostname's password: debug3: packet_send2: adding 48 (len 73 padlen 7 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). debug2: fd 5 setting O_NONBLOCK debug3: fd 6 is O_NONBLOCK debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug1: channel 0: free: client-session, nchannels 1 debug3: channel 0: status: The following connections are open: #0 client-session (t3 r-1 i0/0 o0/0 fd 5/6 cfd -1) debug3: channel 0: close_fds r 5 w 6 e 7 c -1 debug1: fd 0 clearing O_NONBLOCK debug3: fd 1 is not O_NONBLOCK Connection to hostname closed by remote host. Transferred: sent 2176, received 1848 bytes, in 0.0 seconds Bytes per second: sent 127453.3, received 108241.6 debug1: Exit status -1 Connection closed For a successful user: sftp -vvv good_user@hostname debug1: Next authentication method: password good_user@hostname's password: debug3: packet_send2: adding 48 (len 63 padlen 17 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). debug2: fd 5 setting O_NONBLOCK debug3: fd 6 is O_NONBLOCK debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug1: Sending subsystem: sftp debug2: channel 0: request subsystem confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: subsystem request accepted on channel 0 debug2: Remote version: 3 debug2: Server supports extension "[email protected]" revision 1 debug2: Server supports extension "[email protected]" revision 2 debug2: Server supports extension "[email protected]" revision 2 debug3: Sent message fd 3 T:16 I:1 debug3: SSH_FXP_REALPATH . -> / sftp> I cannot figure out why one user will work and the other wont, I have restart the ssh service after adding the user. I have even removed the user and added them again to be sure I am adding it correctly.

  Read the article

• DNS and DHCP dies after ~2 days of use on ClearOS

  - by TheLQ

  I'm using ClearOS (based on CentOS, so any info specific to it should apply here) as a gateway, DHCP, and DNS server. I had this server running perfectly for a month or two before replacing it with another server. However due DNS and DHCP failing 2 days in and a host of other performance issues (the box was a little underpowered), I changed back to the origional server. However 2 days in DHCP and DNS are failing again, and I'm out of idea's on why. In both cases to my knowledge no network or server changes occurred after installation. Right after installing (and at least a day in) DNS and DHCP was working just fine. However later (Day 2) I get a call saying their internet is down (translation: Nobody can get to websites because DNS is down) I've tried to fix the problem by checking if the dnsmasq is even running (it is), restarting the service, and restarting the server to no effect. I do have two internal servers that have static DHCP leases but one's lease must of expired as I can't connect to it anymore. I'm hesitant to do any dhcp testing on the last server as I'll not be able to connect to it anymore. Is there anything anyone can think of on why DNS and DHCP would fail 2 days in to running perfectly? More info: Running dnsmasq in debug mode. This is all that's displayed even when running nslookup quackwall. I'm not sure though if nslookup commands should show up in the log [root@quackwall ~]# /usr/sbin/dnsmasq -dq dnsmasq: started, version 2.49 cachesize 150 dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP dnsmasq-dhcp: DHCP, IP range 10.0.0.100 -- 10.0.0.254, lease time 12h dnsmasq: reading /etc/resolv.conf dnsmasq: using nameserver 74.128.17.114#53 dnsmasq: using nameserver 74.128.19.102#53 dnsmasq: read /etc/hosts - 5 addresses dnsmasq-dhcp: read /etc/ethers - 2 addresses On the other server DNS and the Gateway are all configured correctly (10.0.0.2 is quackwall) lordquackstar@quackgame:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.0.0.0 0.0.0.0 255.255.240.0 U 0 0 0 eth0 0.0.0.0 10.0.0.2 0.0.0.0 UG 0 0 0 eth0 lordquackstar@quackgame:~$ cat /etc/resolv.conf nameserver 10.0.0.2 domain highwow.lan search highwow.lan

  Read the article

• Virtual Machine with Bridged Adapter to Centos not accepting ssh from host machine

  - by javadba

  I have a bridged connection on VirtualBox from os/x 10.8.5 host to Centos 5.8 client. But I suspect this is more of a general issue than specific to the host and precise version of linux. Shown below are the networking info from the VirtualBox and from within the guest sshd is running on port 22: [root@oracle-linux ~]# ps -ef | grep sshd | grep -v grep root 3103 1 0 20:22 ? 00:00:00 /usr/sbin/sshd root 14994 3103 0 21:23 ? 00:00:00 sshd: root@pts/1 Port 22 listening: [root@oracle-linux ~]# netstat -an | grep 22 | grep tcp | grep LIST tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2207 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2208 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN Here are ip addresses, still on the guest os: [root@oracle-linux ~]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b9:e5:79 brd ff:ff:ff:ff:ff:ff inet 10.0.15.100/24 brd 10.0.15.255 scope global eth0 inet6 fe80::a00:27ff:feb9:e579/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b4:86:8a brd ff:ff:ff:ff:ff:ff inet 10.0.3.15/24 brd 10.0.3.255 scope global eth1 inet6 fe80::a00:27ff:feb4:868a/64 scope link valid_lft forever preferred_lft forever [root@oracle-linux ~]# I can ssh to the guest from the guest: root@oracle-linux ~]# ssh 10.0.3.15 The authenticity of host '10.0.3.15 (10.0.3.15)' can't be established. RSA key fingerprint is ef:08:19:72:95:4d:e5:28:af:f3:6f:54:07:84:ba:04. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '10.0.3.15' (RSA) to the list of known hosts. [email protected]'s password: Last login: Mon Oct 21 21:24:12 2013 from 10.0.15.100 But can NOT ssh from the host to the guest: 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection Here is bridged connection infO; BTW I looked into other answers, and one of them mentioned doing service iptables stop That did not help. Adapter 2 is a NAT, shown below In case NAT is causing any issues, i shut it down and restarted networking. [root@oracle-linux ~]# /etc/init.d/network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: Still No joy.. 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection

  Read the article

• VMWare tools not installing with an error

  - by JDS

  VMWare tools not installing on Ubuntu 12.04. I'm using Chef to manage the installation, but the Apt commands fail if run manually. I'm using the VMWare tool Debian repo. Example: $ cat /etc/apt/sources.list.d/vmware-tools-source.list deb http://packages.vmware.com/tools/esx/5.0u2/ubuntu precise main When trying to install, most packages seem to go ok, but one, "vmware-tools-foundation", does not. Example: $ apt-get -q -y install vmware-tools-esx-nox=8.6.10-1.precise Reading package lists... Building dependency tree... Reading state information... You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: vmware-tools-esx-kmods-3.2.0-23-generic : Depends: vmware-tools-foundation (>= 8.6.10) but it is not going to be installed vmware-tools-esx-nox : Depends: ...snip list of deps... E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). $ apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: vmware-tools-foundation The following NEW packages will be installed: vmware-tools-foundation 0 upgraded, 1 newly installed, 0 to remove and 118 not upgraded. 7 not fully installed or removed. Need to get 0 B/5,886 B of archives. After this operation, 86.0 kB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 103499 files and directories currently installed.) Unpacking vmware-tools-foundation (from .../vmware-tools-foundation_8.6.10-1.precise_all.deb) ... VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again. dpkg: error processing /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) The key seems to be this error: "VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again." However, I've tryed removing and purging and can't seem to "trick" VMWare tools into thinking the packages are gone. Apt thinks they are gone. Is there some service/file/cache/lock left that VMWare tools sees that makes it think that VMWare tools are still installed? I've googled and googled but there is no answer to this question with my particular circumstances on the interwebs. VMWare's documentation of this error is minimal.

  Read the article

• mysql: job failded to start. mysqld.sock is missing

  - by Freefri

  How can I fix this and start mysql-server? After /etc/init.d/mysql start or service mysql start I get the message start: "Job failed to start" And after # mysqld I get this: mysqld 121123 11:33:33 [ERROR] Can't find messagefile '/usr/share/mysql/errmsg.sys' 121123 11:33:33 [Note] Plugin 'FEDERATED' is disabled. mysqld: Unknown error 1146 121123 11:33:33 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 121123 11:33:33 InnoDB: The InnoDB memory heap is disabled 121123 11:33:33 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121123 11:33:33 InnoDB: Compressed tables use zlib 1.2.3.4 121123 11:33:33 InnoDB: Initializing buffer pool, size = 128.0M 121123 11:33:33 InnoDB: Completed initialization of buffer pool 121123 11:33:33 InnoDB: highest supported file format is Barracuda. 121123 11:33:33 InnoDB: Waiting for the background threads to start 121123 11:33:34 InnoDB: 1.1.8 started; log sequence number 1595675 121123 11:33:34 [ERROR] Aborting 121123 11:33:34 InnoDB: Starting shutdown... 121123 11:33:35 InnoDB: Shutdown completed; log sequence number 1595675 121123 11:33:35 [Note] I try to do what mysql say me to do: mysql_upgrade Looking for 'mysql' as: mysql Looking for 'mysqlcheck' as: mysqlcheck Running 'mysqlcheck' with connection arguments: '--port=3306' '--socket=/var/run/mysqld/mysqld.sock' mysqlcheck: Got error: 2002: Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) when trying to connect FATAL ERROR: Upgrade failed And yes, /var/run/mysql is empty: mysql_upgrade Looking for 'mysql' as: mysql Looking for 'mysqlcheck' as: mysqlcheck Running 'mysqlcheck' with connection arguments: '--port=3306' '--socket=/var/run/mysqld/mysqld.sock' mysqlcheck: Got error: 2002: Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) when trying to connect FATAL ERROR: Upgrade failed And this is my file /etc/mysql/my.cnf # cat /etc/mysql/my.cnf |grep sock # Remember to edit /etc/mysql/debian.cnf when changing the socket location. socket = /var/run/mysqld/mysqld.sock socket = /var/run/mysqld/mysqld.sock socket = /var/run/mysqld/mysqld.sock Then I try to reinstall mysql from cero: apt-get purge mysql-client mysql-common mysql-server rm -R /var/lib/mysql rm -R /etc/mysql rm -R /var/run/mysqld userdel mysql apt-get install mysql-server mysql-client Then, after typing my root password for mysql I get this error: | Unable to set password for the MySQL "root" user ¦ ¦ ¦ ¦ An error occurred while setting the password for the MySQL administrative ¦ ¦ user. This may have happened because the account already has a password, or ¦ ¦ because of a communication problem with the MySQL server. ¦ ¦ ¦ ¦ You should check the account's password after the package installation. ¦ ¦ ¦ ¦ Please read the /usr/share/doc/mysql-server-5.5/README.Debian file for more ¦ ¦ information. And again I can't start mysql getting the same messages.

  Read the article

• Encrypted off-site data storage

  - by Dan

  My business has a rather unique problem. We work in China and we want to implement a file server paradigm which does not store any files locally, but rather in a server overseas. Applications would be saved onto our local machines, but data would be loaded directly into memory from the cloud, e.g. I load a docx into word at the beginning of the day, saving periodically to the cloud as I work on it, and turn off my computer at night, with nothing saved locally. Considering recent events, we worry about being raided by the Chinese authorities, and although all our data is encrypted, it would not be hard for the authorities to force us to give up the keys. So the goal is not to have anything compromising physically in China. We have about 20 computers, and we need an authenticated, encrypted connection with this overseas file server. A system with Active-Directory-like permissions would be best, so that only management can read or write to certain files, or workers can only access files that relate to their projects, and to which all access can be cut off should the need arise. The file server itself would also need to be encrypted. And for convenience, it would be nice if this system was integrated with each computer's file explorer (like skydrive or dropbox does, but, again, without saving a copy locally), rather than through a browser. I can't find any solution online. Does anyone know of a service that does this? Otherwise I'll have to do it myself (which kinda sounds fun, but I don't really have the time), and I'm not sure where to start. Amazon maybe. But the protocols that offices would use on their intranet typically aren't encrypted; we need all traffic securely tunneled out of the country. Each computer already has a VPN to a server in California, but I'm unsure whether it would be efficient to pipe file transfers through it. Let me know if anyone has any ideas. And this is my first post; feel free say whether this question is inappropriate/needs to be posted elsewhere.

  Read the article

• Unable to start auditd

  - by George Reith

  I am on CentOS 5.8 final I recently installed auditd via yum install audit however I am unable to start it. I edited the configuration file to give a verbose output of the error it is recieving in starting up and this is the output: # service auditd start Starting auditd: Config file /etc/audit/auditd.conf opened for parsing log_file_parser called with: /var/log/audit/audit.log log_format_parser called with: RAW log_group_parser called with: root priority_boost_parser called with: 4 flush_parser called with: INCREMENTAL freq_parser called with: 20 num_logs_parser called with: 4 qos_parser called with: lossy dispatch_parser called with: /sbin/audispd name_format_parser called with: NONE max_log_size_parser called with: 5 max_log_size_action_parser called with: ROTATE space_left_parser called with: 75 space_action_parser called with: SYSLOG action_mail_acct_parser called with: root admin_space_left_parser called with: 50 admin_space_left_action_parser called with: SUSPEND disk_full_action_parser called with: SUSPEND disk_error_action_parser called with: SUSPEND tcp_listen_queue_parser called with: 5 tcp_max_per_addr_parser called with: 1 tcp_client_max_idle_parser called with: 0 enable_krb5_parser called with: no GSSAPI support is not enabled, ignoring value at line 30 krb5_principal_parser called with: auditd GSSAPI support is not enabled, ignoring value at line 31 Started dispatcher: /sbin/audispd pid: 3097 type=DAEMON_START msg=audit(1339336882.187:9205): auditd start, ver=1.8 format=raw kernel=2.6.32-042stab056.8 auid=4294967295 pid=3095 res=success config_manager init complete Error setting audit daemon pid (Connection refused) type=DAEMON_ABORT msg=audit(1339336882.189:9206): auditd error halt, auid=4294967295 pid=3095 res=failed Unable to set audit pid, exiting The audit daemon is exiting. Error setting audit daemon pid (Connection refused) [FAILED] The only information I can find online is that this may be due to SELinux, however SELinux is giving me problems of it's own. No matter what I do it appears to be disabled (I want to enable it). The configuration is set to enforced and the server has been rebooted many a time however sestatus still returns SELinux status: disabled. Can anyone shine some light on this problem? EDIT: I don't know if it is related but I noticed the following message appearing in my /var/log/messages Jun 10 16:25:22 s1 iscsid: iSCSI logger with pid=2056 started! Jun 10 16:25:22 s1 iscsid: Missing or Invalid version from /sys/module/scsi_transport_iscsi/version. Make sure a up to date scsi_transport_iscsi module is loaded and a up todate version of iscsid is running. Exiting... I try to start the iSCSI daemon myself (I have not a clue what it does; I am a linux newbie) and I get the following error: Starting iSCSI daemon: FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory [FAILED] If I go to /lib/modules/ I notice the directory exists but is completely empty.

  Read the article

• Forms authentication failed between web server and sql server

  - by Matt Bear

  I've actually found the solution, but I'm trying to understand why it failed, and why my solution fixed the problem. We have an application that uses forms authentication between a web server and sql server, web server runs server 2008, sql server runs 2008 r2, and sql server 2008. In august the sql server was patched with .net 3.5.1, the web server was untouched, and the forms authentication continued to work. 1 week ago we virtualized the web server onto our vSphere server because of failing hardware. Afterwards the form authentication failed with event code 4005, detail code 50201, The ticket supplied was invalid (on the sql server). In fact the sql server started generating Schannel errors and began blue screening 3-4 times a day. At this point I touched the sql server for the first time(ever), the errors were non specific, any reference to them I could find had to do with either zone alarm(which we don't run), or memory errors. So I applied service pack 1, which stopped the blue screening, but did not fix the forms authentication. At this point we had a work around, so we put it on the back burner while we completed another project, and I was able to get back on it last night. First thing was to adjust some code in the webconfig file on the sql server, nothing, next was regenerate and change out the machine key, still no change. Update the DNS servers, no change. Finally I went through and installed all windows updates, two reboots, (over RDP installed a network card driver which failed, and did not have my server room key, that was fun). After that, forms authentication was working again. And the sql server stopped generating as many errors, I've gotten two schannel errors since then. In short, forms authentication began failing when the web server was cloned onto a virtual machine, which caused the sql server to blue sceen? and forms authentication to fail. And could only be fixed by applying patches to the sql server?(I'm wishing I had patched the servers one at a time so I could know for sure which patch on which server fixed it). My question is why did it fail, and why did patching fix it? I hate fixing something without fully understanding the why and how.

  Read the article

• Setting up SSL on apache on linux ubuntu

  - by ThomasReggi

  I'm trying to get SSL to run on my apache web server. I do not have the DNS for the domain setup yet is that an issue? How do I setup SSL on my web server? When I start apache it fails. root@vannevar:/etc/apache2/ssl# service apache2 start * Starting web server apache2 Action 'start' failed. The Apache error log may have more information. The log stats that it's unable to read the certificate. [Thu Jun 28 15:01:02 2012] [error] Init: Unable to read server certificate from file /etc/apache2/ssl/www.example.com.csr [Thu Jun 28 15:01:02 2012] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag [Thu Jun 28 15:01:02 2012] [error] SSL Library Error: 218595386 error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error The contents of /etc/apache2/httpd.conf ServerName [SERVERIP] The contents of /etc/apache2/ports.conf # If you just change the port or add more ports here, you will likely also # have to change the VirtualHost statement in # /etc/apache2/sites-enabled/000-default # This is also true if you have upgraded from before 2.2.9-3 (i.e. from # Debian etch). See /usr/share/doc/apache2.2-common/NEWS.Debian.gz and # README.Debian.gz NameVirtualHost [SERVERIP]:443 NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> The contents of /etc/apache2/sites-available/www.example.com <VirtualHost *:80> ServerAdmin [email protected] ServerName example.com ServerAlias www.example.com DocumentRoot /srv/sites/example.com/public/ ErrorLog /srv/sites/example.com/logs/error.log CustomLog /srv/sites/example.com/logs/access.log combined </VirtualHost> <VirtualHost [SERVERIP]:443> SSLEngine On SSLCertificateFile /etc/apache2/ssl/www.example.com.csr SSLCertificateKeyFile /etc/apache2/ssl/www.example.com.key SSLCACertificateFile /etc/apache2/ssl/comodo.crt ServerAdmin [email protected] ServerName example.com ServerAlias www.example.com DocumentRoot /srv/sites/example.com/public/ ErrorLog /srv/sites/example.com/logs/error.log CustomLog /srv/sites/example.com/logs/access.log combined </VirtualHost>

  Read the article

• How can I prevent an unintentional DDOS running ColdFusion 8 with IIS 6?

  - by Eric Belair

  We had an interesting outage today on one of our client's websites. Out of nowhere, the website was inaccessible. The website runs by itself on a dedicated physical Windows 2000 server (probably overkill, I know, but that's a discussion for a different day). After restarting IIS and ColdFusion Application Service, the problem came back several times. My initial thought was that it was a DNS issue, which happens occasionally - the last time it happened was after Hurricane Sandy when we our ISP was out, and we had to make some network config changes. But, it was not a DNS issue. My second thought was that it was a DDOS attack, but, there's very little reason anyone would want to take this site down. When we called our ISP, the operator on the other end noted that traffic was spiking significantly. As it turned out, the client had unintentionally caused a DDOS on the website, after they FTPed a very large video file, and then mass emailed a link to it. Hundreds of people clicked the link and brought the site to its knees. I am primarily a Website Programmer, but I often have to contribute to server administration at times. Sadly, I'm the resident ColdFusion and IIS expert, but I don't have a lot of experience with this issue. What are some basic steps that I can take to prevent this from happening in the future, since we cannot always control what files the client posts to the website. Here are some ideas I had, but I'm unsure of the impact: Limit the number of connections in IIS. Put media files on a separate server (like an Amazon site, etc.). File requests of this type currently behind a server-script (i.e. /www.site.com/viewFile.cfm?fileId=1424545, where the fileId references a file off the webroot) that logs requests, and pushes the file to the browser using CFCONTENT. I could edit this script to reject requests when they exceed a certain amount in a given time-frame (i.e. a 5MB can be accessed globally 10 times in an hour). This may cause some users frustration, but, if hundreds of users are attempting to view the file, the site is going to crash anyways, as it did today, which is way more frustrating, since there is no "pretty" message explaining why they can't get to the file. I'm open to any suggestions, as I'm continuing my research to report to the CTO with the best options, so that we can put a solution into effect. Thank you.

  Read the article

• RHEL server Yum dependencies not working

  - by Tony

  I have a redhat server that isnt resolving dependencies correctly. I want to install httpd via yum "yum install httpd" and it installs correctly, but when i go to start httpd I get the following error: /sbin/service httpd restart Stopping httpd: [FAILED] Starting httpd: /usr/sbin/httpd: error while loading shared libraries: libaprutil-1.so.0: cannot open shared object file: No such file or directory [FAILED] It is missing the dependency for apr-util package. Weirdly the i386 package is installed and not the x86_64 package. Can anyone shed any light on why the dependencies might not be resolved correctly? ldd /usr/sbin/httpd libm.so.6 => /lib64/libm.so.6 (0x00002b02370db000) libpcre.so.0 => /lib64/libpcre.so.0 (0x00002b023735e000) libselinux.so.1 => /lib64/libselinux.so.1 (0x00002b023757a000) libaprutil-1.so.0 => not found libcrypt.so.1 => /lib64/libcrypt.so.1 (0x00002b0237793000) libldap-2.3.so.0 => /usr/lib64/libldap-2.3.so.0 (0x00002b02379cb000) liblber-2.3.so.0 => /usr/lib64/liblber-2.3.so.0 (0x00002b0237c06000) libdb-4.3.so => /lib64/libdb-4.3.so (0x00002b0237e14000) libexpat.so.0 => /lib64/libexpat.so.0 (0x00002b0238109000) libapr-1.so.0 => not found libpthread.so.0 => /lib64/libpthread.so.0 (0x00002b023832c000) libdl.so.2 => /lib64/libdl.so.2 (0x00002b0238547000) libc.so.6 => /lib64/libc.so.6 (0x00002b023874c000) libsepol.so.1 => /lib64/libsepol.so.1 (0x00002b0238aa3000) /lib64/ld-linux-x86-64.so.2 (0x00002b0236ebe000) libresolv.so.2 => /lib64/libresolv.so.2 (0x00002b0238ce9000) libsasl2.so.2 => /usr/lib64/libsasl2.so.2 (0x00002b0238eff000) libssl.so.6 => /lib64/libssl.so.6 (0x00002b0239118000) libcrypto.so.6 => /lib64/libcrypto.so.6 (0x00002b0239364000) libgssapi_krb5.so.2 => /usr/lib64/libgssapi_krb5.so.2 (0x00002b02396b6000) libkrb5.so.3 => /usr/lib64/libkrb5.so.3 (0x00002b02398e4000) libcom_err.so.2 => /lib64/libcom_err.so.2 (0x00002b0239b79000) libk5crypto.so.3 => /usr/lib64/libk5crypto.so.3 (0x00002b0239d7c000) libz.so.1 => /usr/lib64/libz.so.1 (0x00002b0239fa1000) libkrb5support.so.0 => /usr/lib64/libkrb5support.so.0 (0x00002b023a1b5000) libkeyutils.so.1 => /lib64/libkeyutils.so.1 (0x00002b023a3be000) yet this is the i386 package apr-util-1.2.7-11.el5.i386 : Apache Portable Runtime Utility library Repo : installed Matched from: Filename : /usr/lib/libaprutil-1.so.0

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• Dovecot, Postfix, Postfixadmin - can't send/receive mail

  - by Jack

  I am setting up a mail server: Dovecot and Postfix with MySQL support and Postfixadmin. Spend literally all day trying to figure it out, but I'm still unable to neither send nor receive any emails. To my knowledge, I have configured everything correctly, so either there is another problem, or my knowledge isn't good enough. Here is what I get when I use "echo test | mail [email protected]:" Jul 11 00:41:07 server postfix/pickup[17999]: 5B0D32AE1B: uid=0 from= Jul 11 00:41:07 server postfix/cleanup[19444]: 5B0D32AE1B: message-id=<[email protected] Jul 11 00:41:07 server postfix/qmgr[18513]: 5B0D32AE1B: from=, size=329, nrcpt=1 (queue active) Jul 11 00:41:12 server postfix/smtp[19448]: 5B0D32AE1B: to=, relay=none, delay=5.3, delays=0.1/0.01/5.2/0, dsn=4.4.3, status=deferred (Host or domain name not found. Name service error for name=dsa.com type=MX: Host not found, try again) *@mail.asd.com is changed for privacy reasons, same goes for [email protected]. *The bold text is where it, for some reason, prints out dsa.com - even though I haven't found it anywhere in the files which I've edited during the installation, nor my DNS is .com in the first place. Here is what I get when I try to send out an email from Postfix Admin interface: Jul 11 00:49:08 server postfix/smtpd[19479]: connect from localhost[127.0.0.1] Jul 11 00:49:08 server postfix/trivial-rewrite[19484]: warning: do not list domain asd.com in BOTH mydestination and virtual_mailbox_domains Jul 11 00:49:08 server postfix/smtpd[19479]: 4F7892AE1E: client=localhost[127.0.0.1] Jul 11 00:49:08 server postfix/cleanup[19487]: 4F7892AE1E: message-id=<[email protected] Jul 11 00:49:08 server postfix/qmgr[18513]: 4F7892AE1E: from=, size=317, nrcpt=1 (queue active) Jul 11 00:49:08 server postfix/smtpd[19479]: disconnect from localhost[127.0.0.1] Jul 11 00:49:10 server postfix/smtpd[19492]: connect from localhost[127.0.0.1] Jul 11 00:49:10 server postfix/trivial-rewrite[19484]: warning: do not list domain asd.com in BOTH mydestination and virtual_mailbox_domains Jul 11 00:49:10 server postfix/smtpd[19492]: 743AE2AE1F: client=localhost[127.0.0.1] Jul 11 00:49:10 server postfix/cleanup[19487]: 743AE2AE1F: message-id=<[email protected] Jul 11 00:49:10 server postfix/qmgr[18513]: 743AE2AE1F: from=, size=772, nrcpt=1 (queue active) Jul 11 00:49:10 server postfix/smtpd[19492]: disconnect from localhost[127.0.0.1] Jul 11 00:49:10 server amavis[13437]: (13437-11) Passed CLEAN, LOCAL [127.0.0.1] - , Message-ID: <[email protected], mail_id: 86+KQY93ANel, Hits: -0.002, size: 317, queued_as: 743AE2AE1F, 2145 ms Jul 11 00:49:10 server postfix/smtp[19489]: 4F7892AE1E: to=, relay=127.0.0.1[127.0.0.1]:10024, delay=2.3, delays=0.17/0.01/0/2.1, dsn=2.0.0, status=sent (250 2.0.0 from MTA([127.0.0.1]:10025): 250 2.0.0 Ok: queued as 743AE2AE1F) Jul 11 00:49:10 server postfix/qmgr[18513]: 4F7892AE1E: removed I really don't know what might be the problem... If you need to know something, feel free to ask and I'll clarify something.

  Read the article

• Ubuntu unattended-upgrades stops apache

  - by Robbie

  This morning i was alerted to the fact that both apache instances serving my app were not responding to requests from my load balancer. I attempted apachectl restart and it said apache was not running. So, i started apache on both instances and got the service up again. I then followed the logs and worked out that both had performed upgrades via the unattended-upgrades package moments before they stopped responding. /var/log/unattended-upgrades/unattended-upgrades.log 2013-07-02 06:30:51,875 INFO Starting unattended upgrades script 2013-07-02 06:30:51,875 INFO Allowed origins are: ['o=Ubuntu,a=precise-security'] 2013-07-02 06:33:57,771 INFO Packages that are upgraded: accountsservice apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common apparmor apport apt apt-transport-https apt-utils bind9-host binutils dbus dnsutils gnupg gpgv isc-dhcp-client isc-dhcp-common krb5-locales libaccountsservice0 libapt-inst1.4 libapt-pkg4.12 libbind9-80 libc-bin libc-dev-bin libc6 libc6-dev libcurl3-gnutls libdbus-1-3 libdbus-glib-1-2 libdns81 libdrm-intel1 libdrm-nouveau1a libdrm-radeon1 libdrm2 libexpat1 libfreetype6 libgc1c2 libgnutls-dev libgnutls-openssl27 libgnutls26 libgnutlsxx27 libisc83 libisccc80 libisccfg82 liblwres80 libruby1.8 libx11-6 libx11-data libxcb1 libxext6 libxml2 linux-firmware linux-image-virtual linux-libc-dev linux-virtual multiarch-support openssl perl perl-base perl-modules python-apport python-crypto python-keyring python-problem-report python-software-properties ri1.8 ruby1.8 ruby1.8-dev sudo tzdata update-manager-core 2013-07-02 06:33:57,772 INFO Writing dpkg log to '/var/log/unattended-upgrades/unattended-upgrades-dpkg_2013-07-02_06:33:57.772399.log' 2013-07-02 06:36:10,584 INFO All upgrades installed I'm running Ubuntu 12.04 on Amazon EC2 servers. I have unattended-upgrades installed and configured as follows: /etc/apt/apt.conf.d/50unattended-upgrades // Automatically upgrade packages from these (origin:archive) pairs Unattended-Upgrade::Allowed-Origins { "${distro_id}:${distro_codename}-security"; // "${distro_id}:${distro_codename}-updates"; // "${distro_id}:${distro_codename}-proposed"; // "${distro_id}:${distro_codename}-backports"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { }; /etc/apt/apt.conf.d/20auto-upgrades APT::Periodic::Update-Package-Lists "1"; APT::Periodic::Unattended-Upgrade "1"; I've struggled to find documentation about what happens to running processes during an upgrade. - Is this expected behaviour? Or should unattended-upgrades restart apache after upgrading it? - What can I do to ensure apache is restarted correctly? Should I just blacklist the apache package?

  Read the article

< Previous Page | 861 862 863 864 865 866 867 868 869 870 871 872  | Next Page >