Search Results

Search found 29636 results on 1186 pages for 'fine uploader'.

Page 866/1186 | < Previous Page | 862 863 864 865 866 867 868 869 870 871 872 873  | Next Page >

• Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• How to find the reason for a weekly downtime on an Ubuntu web server hosted by AWS?

  - by IceSheep

  We started monitoring our web server using Pingdom and found out that we have a downtime of a few minutes every Sunday at 0:00 UTC. The test runs every minute and checks if a successful HTTP response (code 200) is returned on port 80. The test fails due to a timeout (no response after 30 seconds). Here's what we've already checked – without success: Since we run our webserver behind a load balancer, I've set the Pingdom test on the load balancer's public DNS and the webserver's public DNS in order to find out if there's a problem with the AWS load balancer – both tests return the same result We set up Munin on our webserver. Everything looked fine even after the failure. Since the last failure lasted only 2 minutes I suppose Munin couldn't capture a potential problem (it only checks every 5 minutes) I have checked /var/log/apache2/error.log and /var/log/syslog for suspicious entries I have checked /etc/cron.weekly and /etc/crontab for suspicious entries I have searched for files created or last-modified during 0:00 and 0:15 using this method: touch -t 201209020000 start touch -t 201209020015 end find / -newer start -and ! -newer end (nothing found) Has anybody experienced a similar problem? Any proposals on how to find the reason for this behavior? It's Ubuntu 10.04 LTS running on an AWS m1.large instance. Thanks!

  Read the article

• Win7 loses connection to network shares after resume unless server specified using FQDN

  - by Szonja Zemkó

  My Win7 client has a connection to a Linux server and its shared folders. The problem occurs when the computer wakes up after a sleep and then one of the shared folders is not accessible. I receive the following message: Error code: 80070035, The network path was not found. I have problem with one specific folder only. When I restart the computer this problematic folder is accessible again. When I log off before sleep the folder is accessible after wakeup. If I try to access the folder by using the FQDN of the server or the server IP it is also accessible. As a temporary solution I mapped the folder to a network drive using the FQDN and it's working fine but it's inconvenient since every other folder is accessible on the server. To summarize: \server\problematicshare no longer works after resume (the Samba server sees my client connect, then disconnects a few seconds later while I receive the above error message) \server\othershare works after resume \fqdn.of.server\problematicshare always works \ip.of.server\problematicshare always works once the problem manifests, I'm no longer able to restart the "Workstation" service (it is not responding) restarting the "Computer Browser" service has no apparent effect the event log doesn't contain anything that seems relevant "ping server" works

  Read the article

• windows 2008 r2 iis worker proccess memory usage increase

  - by nLL

  I have this web site written in c#. around 400-500 users online at any time. it was on windows 2008 32 bit machine before and never ever locked/slowed down due to increased memory consumption up until i upgraded it's server to win 2008 r2 64 bit. Old server had only 4 gig ram and quad core cpu at 2ghz. site was working just fine. since i've upgraded the server i noticed (2 times with in 10 days) it started to eat ram. last night it went up to 4 gb ram. with ram increase response slows down quite a lot. recycling app pool doesn't help. I have to restart it's worker process to recover. i've noticed this usually happens if there are continuous errors. as i didn't change anything in the code am i safe to assume it is not related to memory leak in the code? did anyone came across something like that? same thing happens if i create continuous errors with classic asp. thanks

  Read the article

• What are possible results/side effects if replication between DC's in a Windows domain is unable to occur?

  - by hydroparadise

  There's plenty of administration literature out there how to properly manage Windows servers. But in dealing with real life, things don't always occur like you want them to. In Microsoft's Windows Server 2003 Administrator's Companion, out of 1400+ pages, theres only one page that I could find when it comes up setting up additional domain controlers. They make it sound seemless and don't reveal a whole lot on what happens if "peer" DC's are unable to replicate. Down to the specific issue at hand, we had a DC go down about a month ago due to a bad RAID controller. There was nothing critical that waranted imediate attention, so bringing it back up got put on the back burner. A month later, we get the DC back up and running and everyting seemed ok. The next day, nobody is able to logon complaining that the "user does not exist" or "unable to establish a trust relationship". Knowing that I had just put the downed DC back on the network, I immediately took it back off the network and had everybody restart the workstations. After that, exchange was fine, shares became available, and everybody was able to log in. After doing some event log swimming, it would appear that everything started due to replication issues on the SYSVOL. I've read where you can force replication, but that would mean putting it back on the network. I am afraid to put the DC back on the network in fear that something else could go wrong. So, what other issues could one expect to run into where two DC's are unreplicated for over a month?

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Hi - Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message : "Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions? Many thanks Clem

  Read the article

• Hard Reset USB in Ubuntu 10.04

  - by Cory

  I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

  Read the article

• ImageMagick installation confusion

  - by Codemonkey

  Well this is turning out to be a pain. I'm on CentOS 6.5. I saw on the PECL ImageMagick changelog that they added a load of constants for new filters, such as LANCZOS2SHARP. Some testing I did earlier suggested that PhotoShop 6.5 was able to downsize photos with better clarity than my current ImageMagick's best effort of LANCZOS, so I thought I'd try to upgrade to test out the newer filters. So, first port of call - get source from pecl for 3.2.0RC1. Installed with no problems. But, ah-ha. Although it says it only requires IM 6.2.4, the filters I'm after don't work unless you have 6.6.6+ So I go http://www.imagemagick.org/script/install-source.php to install the newest version. This is the bit that's puzzled me. It all appears to have installed fined. The tests work fine, passing 40 out of 40. If I run identify -version on the command line it outputs 6.8.9 But if I echo Imagick::getVersion() in PHP it shows 6.5.4, even after restarting php-fpm. rpm -qa | grep ImageMagick shows that I still have 6.5.4 installed locate ImageMagic also only seems to show the 6.5.4 one I feel that the missing link here is ImageMagick-devel, do I need to install that too? How do I go about doing that? Or do I just need to reinstall the pecl-imagemagick 3.2.0RC1 now that I have the latest IM installed?

  Read the article

• Good Hosting Providers With Zend Framework Support [closed]

  - by manyxcxi

  I currently use ixwebhosting for my hosting services. They're cheap and work (most of the time). The databases are horribly slow, the servers are horribly slow, and their support (though usually prompt) is tough to deal with. That being said, they're cheap, I've got like 20 domains hosted in my account, none of them are high volume, and they work JUST good enough- until today. This isn't meant to be a condemnation of ixwh though. Their prices are very low for what they do offer and most things work just fine, most of the time. I need to be able to host web apps written with Zend Framework in a fairly easy fashion. The server performance can't be worse than what I've already had (a pretty low hurdle to clear), and I don't want to spend $30/mo. These are not money making websites- they're projects. My requirements are PHP 5.3, ZF support, MySQL databases, multiple domains- not much. Who should I look at, and who should I look out for?

  Read the article

• Looking for a powershell script that can pull a file from a set of PC's and FTP

  - by DangeRuss

  I'm looking to write a script (preferably powershell) that will essentially copy a file from a bunch of PC's and FTP it to a server. So the structure of the environment is that we have a file on multiple PC's (around 50 or so) that need to placed on a server. Sometimes one of the PC's may be turned off so the script would first need to ensure the PC is up and running (maybe a ping result), then it would need to go into a directory on that PC, pull a file off of it, rename the file, place into a source directory, then remove the file. Naming convention doesn't matter, but date/time stamp would be easiest. Ideally, it would be best to first move all the files to a source directory to save on FTP bandwidth, but since the files will be named the same, the files must be renamed during the move process. Move not copy because the directory needs to be empty so the file can be re-created the next day. So once moved to the source directory, now all the files need to be FTP'd to a server for processing. After all of this, we need to know which PC's on the list did not respond so we can manually retrieve the file so the script should output a file (txt is fine) that will show which PC's were offline. Everything is one domain and script will be run from an server with admin creds. Thank you!

  Read the article

• JavaScript settings are on but I still have issues with web sites using JavaScript.

  - by Mike

  I have two computers that are the same at home except I have installed Adobe Acrobat 9 Pro Extended on my main computer along with the 2010 Outlook (Beta). I have issues when I log into a website that uses pop up calendars to select the date. I pasted it below. I checked my other computer and it is fine. I've checked the Java setting and they are correct. I am at a loss. Any suggestions? Webpage error details User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; HPDTDF; OfficeLiveConnector.1.4; OfficeLivePatch.1.3; eMusic DLM/4; .NET4.0C) Timestamp: Mon, 26 Jul 2010 22:03:59 UTC Message: 'CalendarPopup' is undefined Line: 390 Char: 2 Code: 0 Message: 'CalendarPopup' is undefined Line: 410 Char: 2 Code: 0

  Read the article

• Windows 7: moved system partition, need to update boot partition

  - by Actorclavilis

  So, I have a decently standard Windows7/Ubuntu dual-boot setup, and (since Ubuntu is my usual operating system) I found I needed to grow my Ubuntu partition and shrink my W7 partition. Originally, my system (500G) looked like this: W7 Boot Partition (1.5G) Ubuntu (around 240G) W7 (same as Ubuntu) (on an extended partition, all by itself) Swap (rest of disk, around 16G) Now I'm no stranger to partitioning and filesystem tools, especially GParted, which I used on a Linux boot disk. After my partition editing, the partitions are laid out the same, except the Ubuntu partition is now 407G and the W7 partition is smaller to compensate. I had supposed, based on http://www.gparted.org/faq.php, that I would be able to run the W7 install disk in recovery mode and have it deal with the rearrangement, then possibly reinstall GRUB or something. Well, now the W7 install disk doesn't even see my W7 installation. All my files are there, the NTFS is perfectly clean, no problems there, but the install disk won't notice it. (Of course, the GRUB entry works fine but the W7 boot partition (which I didn't change) refuses to boot it.) So, basically, any ideas on how to fix this? I don't especially want to rerun the entire install procedure because I'll have a bunch of programs to reinstall (never mind redoing GRUB), but I fear that might be the only option. Thanks.

  Read the article

• Grub Installation Failed: Fatal Error ... now what I do?

  - by eklavya

  I know there are some threads that touch this but I feel I have done something uniquely stupid. hence the post and plea for help. I am a beginner @ Linux. So I have a PC with a HDD (hard disk drive) and SSD (solid state drive) It was running Linux Mint /dev/sda1 - HDD Partition 1 - 2 TB (mounted this is /home /dev/sda2 - HDD Partition 2 - 1 TB (separate back up drive, i was backing up files to this) /dev/sdb1 - SSD Partition 1 - 100 GB (OS) /dev/sdb2 - SSD Partition 2 - 20 GB (Swap) The operating system was Linux Mint and was installed on the /dev/sdb1 i.e the solid state drive. I had partitioned off the sda into 2 TB and 1TB and presented the 2 TB as the /home to the OS. Anyway last night I decided to make a return to Ubuntu via the path of Elementary OS. Everything went fine with the install until it stated that GRUB installed failed and this was a Fatal error (no kidding I said). No I am stuck. I have definitely done something wrong and don't know what it is... My biggest pain is the files on the /dev/sda2. I want to save these before I try something drastic like wiping off the /dev/sda completely. So I have the following questions... Can I use a liveCD USB to save these files ? I can see the /dev/sda2 but was unable to access the files in the liveCD last not least ... how do I fix the main issue here. Why could the OS not install GRUB 2b... why is my SSD the /dev/sdb ... and not /dev/sda. Does that have something to do with it that my master boot record sits on the HDD /dev/sda and not /dev/sdb

  Read the article

• Installing a new Motherboard in a HP xw6200 case

  - by thing2k

  I have a HP xw6200 Workstation, that is rather long in the tooth, and with 2 physical CPUs, it is quite inefficient. So, the plan was to upgrade the internals. Nothing special: AMD Athlon II X4 640 ASUS M4A78KT-M LE (mATX) 2x 2GB DDR3 1333MHz RAM. 3p under my £150 budget The issues: The pin connector for the front panel isn't a good fit, but I can trim it to size. The PSU has a 8-Pin Power connector, unsurprisingly, the new board has a 4 pin socket. The pins do line up, but I would have to cut it in half to fit. Finally, due to the weight of heat-sinks, they are screwed directly into the case. It turns out that these screws also lock the motherboard in place. As to remove it, you remove the heat-sinks, slide the motherboard across and lift it out. I tested the new board for fit, and while it slots in fine, it's not secure. There is nowhere to screw the board down, it is just held in place with plastic standoffs. The only idea I had, was to wedging something between the side of the motherboard and part of the case. Any suggestions?

  Read the article

• Removing all traces of GNU java and openjdk and replacing with Sun JDK

  - by user61766

  I have installed latest Sun JDk. But when I do: java -version I still got OpenJDK version. So I completely removed OpenJDK. But now when I do: java -version I get even older GNU java 1.5 something libgcj. So I completely removed that too but it was asking to remove bunch of dependent apps like OpenOffice.org Writer etc. Even though I need the writer, I let it go because I do not want ever to see the face of any GNU java on my linux. So everything related to GNU java is removed. Luckily I am able to start Eclipse and it works fine and start normally (apparently using the installed Sun JDK which is what I want). But now when I run java -version I get bash: /usr/bin/java: No such file or directory Now what I need to do so that when I open any terminal window and enter java -version I should get Sun JDK version? Sun JDK is installed in /usr/java/jdk1.6.021. I also have symlinks: /usr/java/latest and /usr/java/defaults pointing to sun jdk.

  Read the article

• Scripting around the lack of user:password@domain url functionality in jscript/IE

  - by Idiomatic

  I currently have a jscript that runs a php script on a server for me, dead simple. But... I want to be atleast somewhat secure so I setup a login. Now if I use the regular user:password@domain system it won't work (IE decided it was a security issue). And if I let IE just remember the password then it pops up a security message confirming my login every time (which kills the point of the button). So I need a way to make the security message go away. I could lower security settings, which tbh I am fine with but nothing seems to make it fuck off (there might be some registry setting to change). Find a fix for jscript that will let me use a password in the url. There used to be a regedit that worked for older systems which allowed IE to use url passwords (not working on my 64bit windows7 setup) though I doubt that'd have helped jscript anyways (since it outright crashes). Use an app other than IE. Inwhich case I'm not sure how to go about it, I want it to be responsive and invisible so IE was a good choice. It is near instant. Use XMLHttpRequest instead of IE directly? May even be faster but I've no idea if it'd help or just have the same error. Use a completely different approach. Maybe some app that can script website browsing. var args = {}; var objIEA = new ActiveXObject("InternetExplorer.Application"); if( WScript.Arguments.Item(0) == "pause" ){ objIEA.navigate("http://domain/index.html?pause"); } if( WScript.Arguments.Item(0) == "next" ){ objIEA.navigate("http://domain/index.html?next"); } objIEA.visible = false; while(objIEA.readyState != 4) {} objIEA.quit();

  Read the article

• Subversion COPY/MOVE - File not found: transaction 'XXX-XX'

  - by theplatz

  I'm attempting to create a branch in one of my subversion repositories and keep running into an error. No mater what is done, I keep getting the following: File not found: transaction '3062-2e6', path '/Software/XXXXXX/branches/testbranch' I've noticed that the first part of the '3063-3e6' in the above message is the last successful committed revision in the repository. My apache logs don't give much more information: [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] Could not MOVE/COPY /svn/p070361/!svn/bc/3049/Software/SXXXXXX/trunk. [404, #0] [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] Unable to make a filesystem copy. [404, #160013] [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] File not found: transaction '3059-2e2', path '/Software/XXXXXX/branches/testbranch' [404, #160013] This is all happening on a server with an nginx frontend that proxies to Apache for the subversion bits. Other repositories are able to branch fine and I was able to create the branch using file:/// from the command line on the server this is occurring on. The permissions on this repository match every other repository and disk space is not an issue.

  Read the article

• Utilu IE Collection IE6 crashes under Windows 7

  - by Aron

  I've installed Utilu IE Collection under Windows 7 64-bit, but am unable to successfully run IE6 (specifically, "Internet Explorer 6.0 (6.00.2900.2180)"). I haven't tried other versions of IE from the package, so their behavior is unknown. It starts up fine, but the address bar isn't shown. (Attempted to post image, but I'm a newbie on SU and it wouldn't let me. Can be found here.) View-Toolbars shows 'Address Bar' already selected. If I try to (de-)select Address Bar in that list, it crashes: Problem signature: Problem Event Name: APPCRASH Application Name: iexplore.exe Application Version: 6.0.2900.2180 Application Timestamp: 41107b81 Fault Module Name: StackHash_e162 Fault Module Version: 0.0.0.0 Fault Module Timestamp: 00000000 Exception Code: c0000005 Exception Offset: 00000000 OS Version: 6.1.7600.2.0.0.256.48 Locale ID: 1033 Additional Information 1: e162 Additional Information 2: e1625455580a00d3fda64a8cdf366fbb Additional Information 3: 58c7 Additional Information 4: 58c75753c6745fad91929ab6430a83fa That's not all that's wrong ('Search' pane has no contents as well, probably more), but it's the most glaring problem. I've seen some allusions to a registry change needed to fix this, but haven't been able to find any details. Anybody? I'm running the latest version of the collection, 1.7.0.6.

  Read the article

• Tried to install Mint to a Flash Drive. Now I can't boot from the main hard disk.

  - by Dan

  Hello, all. I'm kind of new to Linux and I need some help. I wanted to install a Linux distro to a flash drive so that I can have a portable OS with all my settings, programs, etc. wherever I go. So I fired up a Linux Mint Live CD and installed Mint to the flash drive, and this seems to work OK. But now, whenever I try to boot up my system normally without the flash drive plugged in, it doesn't seem to work. It basically hangs for a bit, and then I get the following prompt: error: no such device: (some long hex val) grub rescue> However, when I try powering my system up when the USB is plugged into the computer, it gives me an option between using the OS installed on my USB and the OS installed on my HD. Selecting the latter, everything loads up just fine. I'm guessing that installing Mint to the flash drive somehow messed with my native Grub installation, but, again, I'm kind of new to Linux, so I'm not sure exactly why. Any help is greatly appreciated.

  Read the article

• Why is /dev/urandom only readable by root since Ubuntu 12.04 and how can I "fix" it?

  - by Joe Hopfgartner

  I used to work with Ubuntu 10.04 templates on a lot of servers. Since changing to 12.04 I have problems that I've now isolated. The /dev/urandom device is only accessible to root. This caused SSL engines, at least in PHP, for example file_get_contents(https://... to fail. It also broke redmine. After a chmod 644 it works fine, but that doesnt stay upon reboot. So my question. why is this? I see no security risk because... i mean.. wanna steal some random data? How can I "fix" it? The servers are isolated and used by only one application, thats why I use openvz. I think about something like a runlevel script or so... but how do I do it efficiently? Maby with dpkg or apt? The same goes vor /dev/shm. in this case i totally understand why its not accessible, but I assume I can "fix" it the same way to fix /dev/urandom

  Read the article

• Exchange 2013 really slow outside of localhost

  - by ItsJustJP

  We've got a 12 core xeon, 24GB of ram 2012 server. We've recently migrated from exchange 2010 (which was on another server) to exchange 2013 which resides on our new 12 core server. Accessing the OWA on the exchange server is fine; it's very quick and responsive however accessing it via any other computer connect to the domain via a 1 gpbs connection and it'll take 10-15 seconds to load. Also running slow is public calenders that people in my place need to access, again taking 10-15 seconds to access and can sometimes cause outlook to not respond. Further to that we have phones that connect via the internet (of course) to the exchange so people can get work emails when they are out of the office. Guess what, this is also running slow. I've have search for many solutions and have tried changing outlook authentication methods but there is no change in speed. The old exchange 2010 server no longer exists but there was no problem before the migration. Has anyone got any suggestions? Thanks :) Must also mention that server 2012 that exchange 2013 is installed on is also the DC. Update: It would appear that any connection via https is slow. It took more than 15 mins for an outlook client to download 50MB of emails (outlook anywhere).

  Read the article

• Computer will not boot - disk read error - cannot boot from HD or DVD

  - by Grant Palin

  This is a 3 year-old system: HP a1640n. There have been no issues with it in the past. I added a video card 2 years ago, and more memory 1 year ago, both without issues. There haven't been any recent hardware changes. I did install Win7 in Oct., but there were no issues with that either. I used the computer fine two nights ago, and turned it off. Yesterday, I tried to turn it on, and got the error: "A Disk Read Error Occurred. Press CTRL ALT DEL to restart" So I restart, see the initial start screen (HP) and enter the BIOS. The hard drive and dvd drive appear to be listed, but the names are gibberish text. I tried putting a Windows disk in the dvd drive, and continued with the boot, but the disk did not get recognized. Even though the BIOS was set to check for optical media before the hard drive. Back to the error screen. If the computer would boot from a cd or dvd, I would just figure the hard drive needed replacing. But both being problematic worries me. Is this a matter of replacing both the hard drive and dvd drive, or might it be an indication of a bigger problem? Thanks for any advice.

  Read the article

• Diff bios - corrupt video driver

  - by sfonck

  Hi, I'm using an Dell M90 Precision Laptop which has a NVidia Quadro FX 2500M graphics card and is running Windows XP. Laptop has been running fine - but a few weeks ago screen went 'white' - restarted computer- bios and startup screens show weird green dots and stripes, normal startup only shows a black screen... only VGA mode works to display something. I've been trying to remove and reinstall the correct drivers downloaded from Dell's website - no solution. I gave up and reinstalled XP - everything was working perfect again. 2 weeks later - again the white screen - tried everything again (flashin new bios also - nothing works) Reinstalled XP - everyhting was working again, so I made a DriveSnapShot of the partition. Today - again the 'white screen'. Ok, no problem ...I was thinking all I needed to do was to restore the DriveSnapShot backup... Few minutes later the backup is restored ... but guess what: video driver does not work correctly... As the DriveSnapShot restored the complete partition, as it was at the time everything was working perfectly, this would mean my driver problems are due to 'settings' in the bios or on the graphics-card itself + these 'settings' can get overridden by doing a new XP-install.... I'm out of options, can somebody help me to find a solution for this problem: Is there some way to backup and restore a bios after seeing some problems? Is there some way to know what is causing this problem like a bios diff utility? Thanks!

  Read the article

• Must have local user to authenticate Samba to AD?

  - by Phil

  I've got a CentOS 5.3 server with Samba running. I've joined this server to my domain in the hopes of allowing AD users some access to my Samba shares. I've found that this works, but only as long as the AD username that I'm trying to authenticate with is also a local user on the server. In other words, if I'm trying to access a share, and try to authenticate with the AD username "joe", I get errors unless I create a user named 'joe' on the server. I don't have to create a matching password or anything....the local user's password is always blank, so I do know that the authentication is actually happening against the AD. Here's my smb.conf file: [global] workgroup = <mydomain> server string = <snip> netbios name = HOME security = ADS realm = <mydomain.com> password server = <snip> auth methods = winbind log level = 1 log file = /var/log/samba/%m.log [amore] path = /var/www/amore browseable = yes writable = yes valid users = DOMAIN\user1 DOMAIN\user2 DOMAIN\user3 DOMAIN\user4 I would assume that my kerberos settings are fine, as I've joined the domain and can use wbinfo to see users and groups. However, I can provide that info if necessary. Anyone have any ideas?

  Read the article

• Xamp on ubuntu serves php source for root url only

  - by mazaryk

  Hey, Okay, so installed xamp on my ubuntu machine, started it up and everything worked. Apache ran my php app just fine (including requests to the root url "/"). However, after the first reboot since installing, when I request "http://localhost/" apache serves up the index php page as a phtml source file. All other urls (like "http://localhost/login") work as expected. Backgound: The only modification I made to xamp was to setup a vhost for my app. The app uses an .htaccess file where I define some rewrite rules (the app is an MVC framework and all urls are rewritten to a single entry point php file). I'm using Xamp because I need php = 5.3.0. I know apache will serve up the source of a php file when it doesn't know to process php files. But the config does indeed have "AddType application/x-httpd-php .php" and as I said, the app works for all urls except the root "/" (and only since I've rebooted). The .htaccess file does contain a DirectoryIndex directive. xamp 1.3.7a Ubuntu 9.10 Any ideas?

  Read the article

< Previous Page | 862 863 864 865 866 867 868 869 870 871 872 873  | Next Page >