Search Results

Search found 2436 results on 98 pages for 'hdd cloning'.

Page 89/98 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

• System occasionally hangs boot process with SLES 11

  - by ThaMe90

  I have several (new) systems on which I had to install SLES11 on. However, after a few (though not every) reboots, the system hangs during the boot sequence. It will only continue after I physically press a key on the keyboard. From what I've found in the dmesg log from a failed boot is the following: [ 22.170276] sd 0:0:0:0: [sda] Mode Sense: b7 00 00 08 [ 22.171155] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 22.182760] sda: sda1 sda2 sda3 [ 22.383424] sd 0:0:0:0: [sda] Attached SCSI disk [ 22.545372] PM: Marking nosave pages: 000000000009a000 - 0000000000100000 [ 22.545377] PM: Marking nosave pages: 00000000bf780000 - 0000000100000000 [ 22.546217] PM: Basic memory bitmaps created [ 22.590380] PM: Basic memory bitmaps freed [ 22.596284] PM: Starting manual resume from disk [ 22.602319] PM: Resume from partition 8:1 [ 22.602321] PM: Checking hibernation image. [ 22.602479] PM: Error -22 checking image file [ 22.602481] PM: Resume from disk failed. [ 22.718727] kjournald starting. Commit interval 15 seconds [ 22.718960] EXT3-fs (sda3): using internal journal [ 22.718964] EXT3-fs (sda3): mounted filesystem with ordered data mode [ 1555.644404] udevd version 128 started [ 1555.697664] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1555.707961] ACPI: Power Button [PWRB] I've looked around the internet for the PM: Resume from disk failed. message, but this seems to only be important when restoring the system after a hybernate, i.e. restore from the hdd. But this is not my situation. I only get this after a reboot, as I said before. The timestamp [ 1555.xxxxxx] is only the result of me pressing a key on the keyboard. Any suggestions on how to proceed? As I am getting stuck on this issue.

  Read the article

• Windows 7 Blank Screen on Boot / Login

  - by Greg

  I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

  Read the article

• Windows 7 hangs on black screen for a while after log in

  - by steini

  I get the welcome screen. I click on my user and get the "logging on" screen. After that all I get is a black screen with a mouse cursor. I can't even start task manager. No ctrl+alt+del or ctrl+shift+escape. It stays like this for about 10 minutes, then the desktop finally starts loading. According to the hdd led on my case, windows isn't even trying to access the hard drive for that whole time. It's just hanging doing nothing it seems. What I have tried: Uninstalled video driver and removed leftovers with driver sweeper Disabled all startup programs and non microsoft services Loaded "last known good configuration" Ran the alleged "black screen fix" from prevx against my best judgement (don't really like running random exes without knowing what they do at all) None of that works. I can boot into safe mode normally. My specs: i7 920 Gigabyte X58-UD3R Gigabyte HD5870 1GB 12GB Mushkin Silverline 1333MHz Windows 7 Ultimate x64 I'm also having another problem which I suspect is related. After I have gotten the computer up and running, everything works perfectly, but when it's been on for a while it starts behaving strangely when changing display modes. When I start up a game or anything that changes the screen resolution the computer freezes for about a minute every time until I reboot again. I think this is probably related to the black screen problem. Just thought I'd check to see if anyone has had the same problem. Let me know if I should post any more details about my system to help diagnose this. Thanks in advance.

  Read the article

• Dialog box tells me there's a missing driver when installing 64-bit version of Windows 7

  - by Eikern

  I'm trying to install Windows 7 64-bit on my computer (ASUS P6T Deluxe V2, one 80GB HDD and two 1 TB HDDs). When I'm supposed to select whether I want to Upgrade or do a Custom install, I get a dialog box telling me: Load Driver A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the Windows installation media is in the CD/DVD drive, you can safely remove it for this step. I've tried to reach this step using a 32-bit installation disc, but that doesn't generate this message at all. Through the command windows (shift-F10) I can reach all of my drives, including my optical drive, without any problems--so what kind of device driver is it the installation wants? I've tried all the obvious drivers on the CD that followed my motherboard, but I can't seem to find the right one. The problem is that I don't know what device I'm supposed to load the drivers for in the first place. Can anyone help me? Edit: It turned out that my downloaded image was corrupted. I borrowed a DVD from a friend of mine, which worked!

  Read the article

• Advice on Computer Specs for overall development/general use machine

  - by Ender

  At the moment I am restricted to a laptop with 512MB of RAM, a 120GB HDD and a 1.5GHz Intel processor for all my development and general browsing needs, and as you can probably tell using it for anything modern is a painful experience. As a result I've decided to buy myself a new desktop computer, one that will stand the test of time and one that can be upgraded easily. Rather than build the machine myself I've decided to go through Dell as I've had good experiences with them when purchasing computers for my family. I've had my eye on this as it's got a good amount of RAM, has a decent-rated processor and isn't priced too badly. http://www1.euro.dell.com/uk/en/home/Desktops/inspiron-580/pd.aspx?refid=inspiron-580&s=dhs&cs=ukepp1&~oid=uk~en~20211~inspiron-580_d005827~~ Intel® Core™ i5 Processor 750 (2.66GHz, 8MB) Genuine Windows® 7 Home Premium 64bit - English Display Not Included ATI Radeon™ HD 5450 1GB DDR3 graphics 6144MB Dual Channel DDR3 [3x2048] Memory 1TB (7200rpm) SATA Hard Drive DVD +/- RW Drive (read/write CD & DVD) with DVD Burn software 1 year of coverage included with your PC McAfee® Security Centre - 15 Month Protection - English After the pain of using a slow laptop for all this time the main thing I want is speed. I may look to play a couple of basic games on it, nothing too powerful. Obviously I'll be doing some development on it too so it'll have to be able to handle the latest IDE's and Database tools like SQL Server pretty quickly. Finally, should I ever need to improve it I'd like to be able to add more RAM and change some of the parts. I wouldn't have thought this would be a problem but a few people I've spoken to have said that the amount of RAM the motherboard can handle isn't that great. Is this true? How long can I expect to be using this computer before it's too slow? Thanks in advance for the help.

  Read the article

• Time Machine vs Source Control?

  - by Blub

  Finally got convinced to start using some kind of version control for my code instead of zipping down a copy of the project at the end of each day. Downloaded Tortoise SVN and used it to create a repository localy on my hdd. I've been using it for 2 days now but I have to say that using it is actually more hassle than just copying the project manually in explorer. Sure, you only store incremental changes but with the cheap disks of today I can't really say that's an argument when you only have small projects. I haven't realy found a quick way to browse the older versions of my files eighter. What I want is an infinite undo that is completely transparent while I code, if I save the file I want a backup. I don't want to check out, check in and don't even get me started on moving files. I haven't tried Time Machine for OS X but it looks like it's exactly what I'm looking for. Does such a program exist for windows? Preferably free and with some kind of tagging-system so I can tag a timestamp when the project is working etc. Maybe should add that I mostly work alone on a single computer. Update: Some of you asked why I want backup. Since I work alone it's mostly to allow me to quickly hack up a solution without worrying that something will screw up.

  Read the article

• How to display/define Mirror/Stripping pairs with mdadm

  - by Chris

  I want to make a standard linux software Raid10 over 4 HDD. The server has 4HDDs, 2 pairs from different vendors in order to avoid batch problems. I want to have the mirror over two different Vendors, and then the Stripe over the mirror pairs. I could do that by manually creating Raid1/0, but mdadm supports Raid level 10. I just cant figure out how the Raid10 is then handled and how the data is distributed. mdadm --detail /dev/md10 /dev/md10: Version : 1.2 Creation Time : Wed May 28 11:06:23 2014 Raid Level : raid10 Array Size : 1953260544 (1862.77 GiB 2000.14 GB) Used Dev Size : 976630272 (931.39 GiB 1000.07 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Wed May 28 11:06:23 2014 State : clean, resyncing (PENDING) Active Devices : 4 Working Devices : 4 Failed Devices : 0 Spare Devices : 0 Layout : near=2 Chunk Size : 512K Name : pdwhost:10 (local to host pdwhost) UUID : a3de0ad5:9e694ee1:addc6786:c4449e40 Events : 0 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 81 1 active sync /dev/sdf1 2 8 97 2 active sync /dev/sdg1 3 8 113 3 active sync /dev/sdh1 does not really give any information about that. How it should be: Raid 1 / Mirror over /dev/sda1 /dev/sdf1 and /dev/sdg1 /dev/sdh1 Raid 0 over the two Raid 1 pairs Is it possible to do that with the built in "level=10", how can I see what pairs are mirrored? Thanks a lot for you help

  Read the article

• Task scheduled to wake laptop - only works when lid is open

  - by JD Pack

  I am running Windows 7 Starter on an Acer Aspire One laptop. I want my laptop to automatically run a task (backup the HDD to a network drive) once a week in the middle of the night. I scheduled the task in "Task Scheduler" and checked the box to wake the computer to run the task. I also changed the advanced power settings to allow wake timers. This was half of the solution. It now works flawlessly when the lid is open... the computer can wake itself up from either sleep or hibernate mode to perform the backup. When the lid is closed however, its sleeping beauty. Any ideas? I don't want to have to remember to open the lid once a week. It sort of defeats the purpose of an "automatic" backup. Update: I discovered that it can wake from sleep (or hybrid sleep), but not from hibernate when the lid is closed. This is good news. I'd still be curious about how to get it to work from hibernate, but I'm pretty happy about waking from sleep at least.

  Read the article

• Intell SSD + Win 7 after crash can not repair, can not re install

  - by Ori

  I have Lenovo w520, after i bought it i took away old hhd (no longer with me) and replaced it with intel ssd, it worked perfectly for 1 year or so, today my system fr0ze and after waiting for some time i didi hard reset - it wasn't able to boot anymore at all, i do not see any messages from windows ever, it only loads Intel boot utility that suggests to pick one of 3 devices to boot, it has my hdd there but nothing happens. /I dont have recovery tools from lenovo since i moved to another country, i got win 7 cd from a friend (came with his laptop) abd if in bios i have AHCI - it doesnt see my ssd, if compatible mode - it sees it but format not available, partition creation gives b\me 8007045 error. I tried diskpart, in compatible mode it sees my disk but doesnt do recover or clean all, also win 7 disk tools dont do anything if i try to do boot fix... I am ok with erasing it but i seem not to be able too, i jus tneed the machine to wpork asap, all my files are on external drives so i dont care about formatting. please help! I am given a very old machine by a friend so i am able to browse internet... it is under XP...

  Read the article

• Performance decrease in every game and application

  - by Márk Vincze

  When I start a game, initially it runs smoothly, but after a couple of minutes, the performance gradually decreases to the point of being unplayable (1-2 FPS). The sound also starts to lag at this point. This does not happen every time I start my PC, usually exiting the game, rebooting, then starting the game again solves the problem, and I can play with perfect FPS for as long as I want. I could not find any deterministic reason when this happens and when doesn't. It happens in every game I tried (SWTOR, Diablo 3, Skyrim), and not even games, but simple applications like a browser or the Control Panel can get unusably slow. This is a brand new PC I bought three months ago, and this problem occurs since the first day I've been using it. Could you provide any advice how to further diagnose the problem? I tried to reinstall Windows, and tried different video card drivers, but it did not help. It would be important to know whether this is a hardware or software problem, because I can use the warranty if it is a hardware issue. (I did not want to return the PC yet, because I can't reproduce the issue deterministically.) Spec of the pc: Motherboard: ASROCK H61M-HVS CPU: INTEL Core i3-2120 3.30GHz 1155 BOX Memory: KINGMAX 4096MB DDR3 1333MHz KIT Video card: GIGABYTE GV-R685OC-1GD HD6850 1GB GDDR5 PCIE HDD: SEAGATE 500GB Barracuda 7200rpm 16MB SATA3 ST500DM002 I am using Windows 7 64 bit. Thanks a lot in advance!

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• Is there an application to log component temperatures to file?

  - by MrVimes

  I purchased a computer a month or two ago (core i7, 24gb ram, geforce gtx 590, windows 7 ultimate). Within the last week it began to bluescreen regularly. I tried lots of things (check hds, check memory, reinstall windows etc..) but it still bluescreened. At the time my temps were as follows... CPU - aprox 40/50c. GPU - arpox 60 idle, aprox 90 during heavy use. HDDs - aprox 55c after the PC had been on a while. I thought the 55c was ok, but I have since realized it was probably too high and may have been the direct cause of the bluescreening. I've installed a spare fan I had in the front of the PC blowing air in, (so there's airflow from front to back) Since then, obviously, all my temps are down. Especially the HDDs - three of them reach 30c and one has been up to 47c (it is some distance away from the airflow, in one of the 5.25inch drive bays) I haven't had the PC on for as long as it would normally take to bluescreen yet, but If it does I want to know what all the temps were right before the bluescreen. I have tried Everest but it only shows me realtime temps or gives me the ability to create one-off reports. I want something that can record all the temps to a file at 30 seconds intervals. If the computer bluescreens I can load it up again and check the last entry in the file. Side question: Am I right in thinking 55c was far too hot for a HDD? (It might have got higher than that before the bluescreens.. I don't know) Another side question: Is 47c too high? This is actually why I am asking the main question - I am concerned that this one drive that isn't getting the benefit of the extra fan may still cause the computer to bluescreen.

  Read the article

• Hard Drive Compatibility with Motherboard

  - by Wesley

  Here are the current specs to put things in context: ECS P4VXASD2+ V5.0 Intel Pentium 4 Northwood 2.8 GHz 2x 512MB PC2100 DDR266 SDRAM Maxtor DiamondMax 10 250 GB PATA (IDE) HDD Gigabyte 52x CD-ROM NVIDIA TNT2 Pro 16 MB OKIA 300W ATX PSU USB bracket Modem PCI Before, I actually had a 300 GB hard drive installed. However, I read the FAQ for the motherboard and discovered that a maximum of 250 GB hard drive was supported. So I ended up finding the one listed above and put that in. However, upon booting up, I reset the BIOS to defaults and auto-detected all the drives installed. The 250 GB came up as something like 251.0 GB. I didn't think much about it until I tried to boot up a Windows XP installation disc. It booted up successfully and run for about a minute before the computer randomly rebooted. I've made sure that all the jumpers and settings are correct and everything has been installed correctly. I've tried running it without the addons and one stick of RAM but still the same thing. What else could be causing this problem?

  Read the article

• How is the extra mSATA SSD disk used/configured in a Dell XPS laptop?

  - by Mark

  Some machines in the new XPS laptop range from Dell come with a regular, large (500GB+) HDD and an additional 32GB m-SATA SSD. The only detail I can find about this extra drive on the Dell site is this: Store your important files, multimedia and photos with XPS 15’s large hard drive options. To get instant access to your media, choose an optional mSATA solid-state drive (SSD) that can boot up to twice as fast as a regular hard drive and resumes in less than 1 second. I'd like to know more about how this extra drive is set up and used, specifically: Is anything installed on it (e.g. OS files or a boot loader) or is it just used as swap space? Is the m-SATA drive visible as a lettered drive in Windows? (I'd guess not if it's used for swap file only.) Is this unusual configuration likely to cause any problems later down the line - e.g. when upgrading to Windows 8? As usual, Dell's sales team haven't been able to help. If anyone's actually got a Dell machine with this or a similar hard drive set-up and can give a definitive answer rather than speculation I'll accept the answer.

  Read the article

• Why dd finishes instantly when pipelining to cat?

  - by agsamek

  I start bash on Cygwin and type: dd if=/dev/zero | cat /dev/null It finishes instantly. When I type: dd if=/dev/zero > /dev/null it runs as expected and I can issue killall -USR1 dd to see the progress. Why does the former invocation finishes instantly? Is it the same on a Linux box? * Explanation why I asked such stupid question and possibly not so stupid question I was compressing hdd images and some were compressed incorrectly. I ended up with the following script showing the problem: while sleep 1 ; do killall -v -USR1 dd ; done & dd if=/dev/zero bs=5000000 count=200 | gzip -c | gzip -cd | wc -c Wc should write 1000000000 at the end. The problem is that it does not on my machine: bash-3.2$ dd if=/dev/zero bs=5000000 count=200 | gzip -c | gzip -cd | wc -c 13+0 records in 12+0 records out 60000000 bytes (60 MB) copied, 0.834 s, 71.9 MB/s 27+0 records in 26+0 records out 130000000 bytes (130 MB) copied, 1.822 s, 71.4 MB/s 200+0 records in 200+0 records out 1000000000 bytes (1.0 GB) copied, 13.231 s, 75.6 MB/s 1005856128 Is it a bug or am I doing something wrong once again?

  Read the article

• High disk I/O activity in CentOS server

  - by triiim

  I have about 16 websites in a CentOS dedicated, and I am having some problems on high traffic hours, it seems to be a high disk I/O activity causing a general slowdown. I've installed atop and this is what I see on the bottom (the server has been restarted thats why the values are so low): *** system and process activity since boot *** PID RDDSK WRDSK WCANCL DSK CMD 1/18 2176 1.7G 7.3G 854.4M 39 mysqld 671 1248K 3.0G 0K 13 flush-8:0 566 0K 1.1G 0K 5 jbd2/sda2-8 2401 124.2M 529.1M 22408K 3 crond 2032 2.2G 502.0M 0K 12 nginx 2360 425.8M 115.3M 4188K 2 httpd flush-8:0 and jbd2/sda2-8 are the processes I see with iotop using 99% on the IO column, and they are the processes that write the most on the hdd (after mysql). From what I saw in google this could be caused by some ext4 related bug, the current kernel is: Linux srvr.com 2.6.32-71.29.1.el6.x86_64 #1 SMP Mon Jun 27 19:49:27 BST 2011 x86_64 x86_64 x86_64 GNU/Linux I asked the hosting support to update the kernel and they tried but they now say that the server wont boot with the new installed kernel and they had to go back to the previous, they are not helping very much. Does someone has any idea how could I solve the high disk usage caused by flush-8:0 and jbd2/sda2-8 processes?

  Read the article

• Uninstallation of WSUS form SBS 2008

  - by Logik

  I am not much experienced system admin, but i came across the client who was having SBS 2008. The server was running out of HDD space. So to recover some, I removed its WSUS role (twas not needed).this removed WSUS 3.0 SP1 & freed a lot of space. This SBS is: Domian controller, DNS, DHCP, File server. After i removed WSUS i disabled windows update service & i rebooted serer & checked from one of client if the shared folders are accessible. they were. Next day all of sudden i got call from them saying they can't login into their domain. I looked into server, the Active directory service was stopped. I never remember touching any service other than windows update. How come AD service stopped running all of sudden. Is removing WSUS have such impact? I am not aware of any such thing.

  Read the article

• Where did my backup files go? Can they be recovered?

  - by Ken

  I just purchased a Western Digital Essential SE 1TB external hard drive from Best Buy at their recommendation. I then exchanged it for a Toshiba Canvio (I think that was the name). I have a Toshiba Qosmio X505-Q898. The Canvio locked up my computer and rewrote some kind of OS file, and erased all the restore points as well as the system image backup (according to Best Buy) just by plugging it in for the first time. Never even got to the install part or anything -- plugged it in and fried my computer. They spent about an hour and a half on my computer and got it back to a somewhat working condition and gave me access to my files. So now they say I have to back it up using my recovery disk and rewriting my OS. Enter the Essential. Brought it home last night, plugged it in and installed everything. Works perfect, no problems. Backed up everything on it. I unplugged and plugged it twice to make sure that everything was on it. Essential told me it had both the HDD and SSD backed up. So I reinstalled my OS. Plugged the Essential in and everything loads right up. Went to retrieve my files and the Western Digital has nothing on it. It shows all my music, pics, ETC. as still being on my computer and needing to be backed up, but since there are no files on my computer now. Where is this information coming from and where did my files go? It's about 810GB worth of files I've amassed over several years. Is there any way to recover data from this? I plan to contact Western Digital and Best Buy, just thought I would check here too. Any advice will be appreciated as a lot of these files are invaluable to me.

  Read the article

• Master File Table Corrupt, any way to save data?

  - by domen

  hi. I've used search, but none of the results match my problem so I didn't have to ask separate question. I've Installed Windows 7 RTM recently and since then partitions located on one of my HDDs have gone "crazy". They used to "freeze" and didn't open in explorer for some time (minute or two, usually), sometimes all partitions of the drive wouldn't show until reboot and finally, one of those partitions started showing "disk structure is corrupted and unreadable" warning, it appeared in Disk Management window as RAW and chkdsk showed "mft corrupt". There were no important data on the partition and I didn't have enough time to analyze the problem at the moment, so I just reformatted it and ran antivirus scan on system. After that problem settled for some time, but yesterday the problematic HDD vanished again from the system. After reboot chkdsk identified mft of four partitions corrupt and now they are all in same conditions as the above mentioned one. But the difference is that the files stored in them are extremely important. and just for info: I upgraded from Win7 build 7077, but had some performance issues, so I reformatted system drive and installed fresh Win7 RTM on it. I've downloaded TestDisk and it shows all the partitions marked as NTFS (not RAW) and my knowledge of the program wasn't sufficient to obtain any other info from it :-) and the images that could help describe the problem (sorry, I'm not allowed to post images and more than one hyperlink): http:// img22.imageshack.us/img22/5909/chkdskz.jpg http:// img198.imageshack.us/img198/5576/computeray.jpg I'm interested, is there a way to let me restore the MFT or just access files so I can backup them before reformatting the drive. Thanks for your time. :) P.S. my reformatted drive is showing no problems, could there be a problem with windows 7 itself? I googled, but with no results.

  Read the article

• which is best smart automatic file replication solution for cloud storage based systems.

  - by TORr0t

  I am looking for a solution for a project i am working on. We are developing a websystem where people can upload their files and other people can download it. (similar to rapidshare.com model) Problem is, some files can be demanded much more than other files. The scenerio is like: I have uploaded my birthday video and shared it with all of my friend, I have uploaded it to myproject.com and it was stored in one of the cluster which has 100mbit connection. Problem is, once all of my friends want to download the file, they cant download it since the bottleneck here is 100mbit which is 15MB per second, but i got 1000 friends and they can only download 15KB per second. I am not taking into account that the hdd is serving same files. My network infrastrucre is as follows: 1 gbit server(client) and connected to 4 Nodes of storage servers that have 100mbit connection. 1gbit server can handle the 1000 users traffic if one of storage node can stream more than 15MB per second to my 1gbit (client) server and visitor will stream directly from client server instead of storage nodes. I can do it by replicating the file into 2 nodes. But i dont want to replicate all files uploadded to my network since it is costing much more. So i need a cloud based system, which will push the files into replicated nodes automatically when demanded to those files are high, and when the demand is low, they will delete from other nodes and it will stay in only 1 node. I have looked to gluster and asked in their irc channel that, gluster cant do such a thing. It is only able to replicate all the files or none of the files. But i need it the cluster software to do it automatically. Any solutions ? (instead of recommending me amazon s3) S

  Read the article

• In Windows 7 power management, is it possible to set different sleep settings for different SATA disks?

  - by Ben Voigt

  I'm having an issue with Windows 7 either freezing up or generating a BSOD coming out of sleep. I suspect that it is related to my boot/OS drive, an OCZ Vertex SE SSD, because numerous other Vertex users have reported sleep problems. Notably, if I put the computer to sleep, it almost always wakes correctly. If it goes to sleep after a timeout, it almost always BSODs. I disabled timed sleep and now it freezes when left unattended. My next step is to disable "Put hard disks to sleep after X minutes", but I'd like to change this setting only for the SSD and not for the rotating data disks, which I would like to spin down normally. Does anyone know a place to configure sleep on a per-disk basis? I don't need to set different timeouts on different disks (although that would be nice), simply setting "this disk sleeps" and "sleep is disabled for this disk" would be great. Additional system information: Windows 7 Ultimate x64, Core i5 - P55 chipset, Intel RST drivers are installed. One SSD, two rotating HDD, and a DVD-RW drive are all connected to the Intel SATA ports. I could potentially move some of these to my motherboard's other SATA controller if that would help.

  Read the article

• Is it ok to share private key file between multiple computers/services?

  - by Behrang

  So we all know how to use public key/private keys using SSH, etc. But what's the best way to use/reuse them? Should I keep them in a safe place forever? I mean, I needed a pair of keys for accessing GitHub. I created a pair from scratch and used that for some time to access GitHub. Then I formatted my HDD and lost that pair. Big deal, I created a new pair and configured GitHub to use my new pair. Or is it something that I don't want to lose? I also needed a pair of public key/private keys to access our company systems. Our admin asked me for my public key and I generated a new pair and gave it to him. Is it generally better to create a new pair for access to different systems or is it better to have one pair and reuse it to access different systems? Similarly, is it better to create two different pairs and use one to access our companies systems from home and the other one to access the systems from work, or is it better to just have one pair and use it from both places?

  Read the article

• Dual hard drive Windows 7 system, modified the registry to get programs to install on second drive, now IE doesn't work

  - by paul

  I have a dual hard drive Windows 7 system, Windows is installed on an SSD (C:) and I modified the registry to try to force programs to install on second HDD drive (another letter). The registry edits are pretty simple, just a few keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion to change the drive letter. For the most part the system is very fast and works great, but IE doesn't work anymore. With IE10, it opens for a flash with a white window then closes. I tried installed IE11 which opens a white window for a few seconds, doesn't respond, then crashes. I've tried all the solutions I could find. This includes resetting the IE settings, "uninstalling" and re-installing IE, which is just turning it on and off in "Turn Windows Features on or off", copying the Program Files\Internet Explorer files onto both/either drives, changing the registry keys back to use C:, lots of rebooting, and safe mode. Nothing has worked. I don't see errors in the event viewer, but I might not know what to look for. Any ideas on how to get IE running? I don't need IE for daily browsing, I just need it for cross-browser testing on sites I build and on the rare occasion a page only works in IE. I don't really want to use a virtual machine, but would be ok with something standalone like tredosoft's, but I'm not aware of something like that for current versions of IE.

  Read the article

• Why has my computer started to make noises when I turn it on after I put it into sleep mode for the first time a week ago?

  - by Acid2

  I would usually have my pc on all day and fully shut it down at night time before I went to bed. I decided to put it into sleep mode instead the other day and everything was fine but when I woke it from sleep, I was presented with the blue screen of death and it started with some weird noise that sounded like some spinning part was off balance or possibly hitting something periodically. Sounds like it could be a fan or maybe the HDD. I'm not sure why sleep mode would mess up the hardware. Anyway, now sometimes, randomly, when I turn my computer on from a previous shut down, I still get to hear the noise but the start-up is normal. Sometimes I don't hear anything for the entire duration while I have it on and sometimes it goes away after a few minutes and sometimes it doesn't and I have to restart, like it isn't going away right now. I can hear the noise as I type this. Anyone got possible solutions? I don't want to open the system and mess up other stuff. I'm also not sure if I should take it somewhere to have it fixed - it might not make the noise then and work like normal and nothing would seem like needing to be fixed. Add: I'm running Windows 7, if that's of any relevance.

  Read the article

• Recommend a UK based VPS host equivalent to Dreamhost [closed]

  - by Pez Cuckow

  I appreciate this question could be considered subjective and argumentative so can people make recommendations rather than arguing about the best. I believe the "correct" answer is the one closest to what I am looking for. Basically I live in the UK but have been using the US based Dreamhost for about 6 years now, and my web projects are getting to the scale where the websites need to the UK based to cope with the demand and load. I originally had shared hosting with Dreamhost but upgraded to a VPS a while ago, getting 512mb of RAM, unlimited disk space, bandwidth and domains for $30. Their control panel is a custom easy to use build that they have created in house and offers features very similar to other web panels (as far as I am aware). So basically my question boils down to, is there anywhere that offers an equivalent package? In all honesty as long as I have over 50gb HDD space and unlimited domains it doesn't really matter? Are there any VPS providers you would recommend as reliable? I promise to check every link posted, many thanks for your time!

  Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >