Search Results

Search found 14062 results on 563 pages for 'domain forwarding'.

Page 90/563 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

• IP routing Solaris 9 access the internet from local network

  - by help_me

  I am trying to configure the NICS on the Solaris Sparc server. My problem lies in getting out to the "Internet" from the local network. I have requested the NIC to receive a DHCP server address #ifconfig -interface dhcp start. If anyone could guide me as to what I need to do next. I am not able to ping 4.2.2.2 or access the internet. Much appreciated, thank you #uname -a SunOS dev 5.9 Generic_122300-59 sun4u sparc SUNW,Sun-Fire-V210 ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.3 netmask ffffc000 broadcast 10.100.63.255 bge0:2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.22 netmask ffffc000 broadcast 10.100.63.255 bge3: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 12 inet 169.14.60.37 netmask fffffe00 broadcast 169.14.61.255 cat /etc/defaultrouter 10.100.0.254 169.14.60.1 cat /etc/resolv.conf nameserver 169.14.96.73 nameserver 169.10.8.4 netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 169.14.60.37 169.14.60.1 UGH 1 0 169.14.60.0 169.14.60.37 U 1 18 bge3 10.100.0.0 10.100.0.3 U 1 34940 bge0 10.100.0.0 10.100.0.22 U 1 0 bge0:2 224.0.0.0 10.100.0.3 U 1 0 bge0 default 10.100.0.254 UG 1 111 default 169.14.60.1 UG 1 26 127.0.0.1 127.0.0.1 UH 10 59464 lo0 bash-2.05$ sudo ndd -get /dev/ip bge0:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip bge3:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip ip_forwarding 1

  Read the article

• NameServer SOA records misconfigured

  - by Khoa Bui

  This is my config of NS. hostingdk.com. SOA zone1.hostingdk.com admin.hostingdk.com 2010051905; 43100; 7200; 2419100; 86400; hostingdk.com. NS zone1.hostingdk.com. hostingdk.com. NS zone2.hostingdk.com. zone1.hostingdk.com. A 96.30.49.11 zone2.hostingdk.com. A 96.30.46.238 Both zone1 & zone2 have registered name server in Enom domain control panel. My problem is, one domain .lv cant not change DNS to my NS. They said: Error : Nameserver zone1.hostingdk.com cannot be queried for SOA Error : Nameserver zone2.hostingdk.com cannot be queried for SOA Please help me, how to fix it ?

  Read the article

• Forward Hostname via my router to another PC for debugging

  - by Markive

  Hi, My web service runs on for example: http://mydomain.com/mywebservice.asmx. This works great, but I have a PDA application which I want to debug it synchronising through this web service. Currently the only way I can do this is to debug the webservice running on the actual server which is far from ideal. What I would like to do is for any device connecting on my wireless network, if it requests mywebservice.asmx for this to forward the request to my development PC and for IIS to then handle the request and allow me to debug in Visual Studio. So device on the network that requests the hostname: mywebservice.asmx will his this PC.. I am at a loss to set this up on my router (Zoom ADSL X6), this is massively out of my scope but any help would be much appreciated

  Read the article

• Squid - Selective reverse proxy and forward proxy

  - by Dean Smith

  I'd like to setup a squid instance to do selective reverse proxy for a configured list of URLs whilst acting as a normal forward proxy for everything else. We are building new infrastructure, parallel live as it where, and I want to have a proxy that people can use that will force selective traffic into the new platform whilst just acting as a forward proxy for anything else. This makes it very easy for people/systems to test the portions of the new platform we want without having to change too much, just use a proxy address. Is such a setup possible ?

  Read the article

• How to configure traffic from a specific IP hardcoded to an IP to forward to another IP:PORT using i

  - by cclark

  Unfortunately we have a client who has hardcoded a device to point at a specific IP and port. We'd like to redirect traffic from their IP to our load balancer which will send the HTTP POSTs to a pool of servers able to handle that request. I would like existing traffic from all other IPs to be unaffected. I believe iptables is the best way to accomplish this and I think this command should work: /sbin/iptables -t nat -A PREROUTING -s $CUSTIP -j DNAT -p tcp --dport 8080 -d $CURR_SERVER_IP --to-destination $NEW_SERVER_IP:8080 Unfortunately it isn't working as expected. I'm not sure if I need to add another rule, potentially in the POSTROUTING chain? Below I've substituted the variables above with real IPs and tried to replicate the layout in my test environment in incremental steps. $CURR_SERVER_IP = 192.168.2.11 $NEW_SERVER_IP = 192.168.2.12 $CUST_IP = 192.168.0.50 Port forward on the same IP /sbin/iptables -t nat -A PREROUTING -p tcp -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.11:8080 Works exactly as expected. IP and port forward to a different machine /sbin/iptables -t nat -A PREROUTING -p tcp -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.12:8080 Connections seem to timeout. Restrict IP and port forward to only be applied to requests from a specific IP /sbin/iptables -t nat -A PREROUTING -p tcp -s 192.168.0.50 -d 192.168.2.11 --dport 16000 -j DNAT --to-destination 192.168.2.12:8080 Times out as well. Probably for the same reason as the previous entry. Does anyone have any insights or suggestions? thanks,

  Read the article

• Password Expired Server 2008 R2

  - by Shaharyar

  Hello everybody, We're facing some trouble with our Server 2008 R2 installation. The passwords expired and we're prompted to change the password. After changing it, we get following error message: Configuration Information could no be read from the domain controller, either because the machine is unavailable, or access has been denied. But we aren't even using a domain controller. So we tried running the server in Safe Mode where we get following message after changing the password: An attempt was made to logon, but the network logon service was not started. Are there any other things I could try? All help is more than appreciated!

  Read the article

• Port Redirection on Mac OS X Lion

  - by Andreas

  I have tried to solve this issue using pf but with no luck. Basically, I am trying to redirect incoming port 443 traffic to port 22. I have tried to set up a rule in a file and load it in pf but I get syntax error. Can anyone with more experience with pf provide some insight? Here's what I've attempted: pass in on en1 proto tcp from any to any port 443 rdr-to 127.0.0.1 port 22 and pass in quick proto tcp to port 443 rdr-to 127.0.0.1 port 22 I've been able to do this in MacOSX Snow Leopard with ipfw: sudo ipfw add 1443 forward 127.0.0.1,22 ip from any to any 443 in but it doesn't work in Lion (it gives me an Invalid Argument error).

  Read the article

• Corrupted attachments in Thunderbird forward filter

  - by Guandalino

  I created a filter in Thunderbird 14 on client A that, when a certain rule on incoming mail is satisfied, the same mail is forwarded to client B and C. Matching mails received from A are always forwarded to B and C, and that's what I want. Though, when the mail on A has an attachment, it is also forwarded by B and C but the file they receive is corrupted. In my case the incoming file on A is a Word file of about 10kb in size; clients B and C receive a Word file of 27 bytes. I think this could happen because the forward starts from A when the attachment is not yet completely downloaded. I'm not sure this is the cause, though. And I wouldn't have any idea for a fix. Any idea about how to investigate or solve the issue?

  Read the article

• How to browse to a webserver which is reachable through the SSH port only

  - by GetFree

  I have a server at work which is behind a firewall (the company's firewall) so it is reachable only thrugh port 22 (SSH). I'm able to connect to the server with putty without problems. Also, that server has Apache running and listening on port 80 as usual. But I cant connect to the website using my browser since port 80 (and everyone else) is blocked by the company's firewall. Is there a way I can make my browser to connect to Apache in that server so I can browse the site I'm working on? Thanks.

  Read the article

• How to ssh to my dorm computer with shared public IP and no admin rights over the router?

  - by Aamir

  First of all, I am not a Linux or ssh newbie. I have searched for this problem on many forums extensively but nobody seemed to have discussed this. Please help me! I live in a student dorm (off-campus) and all students of the dorm share the same WAN IP (Internet or public IP), which is fortunately static. I am not an admin and have no control over the router that assigns private IP's to all of the students, so I can't really forward port 22 to my computer :( Is it still possible to establish an ssh connection to my dorm computer from a computer on campus?

  Read the article

• Password Expired on Server 2008 R2

  - by Shaharyar

  Hello everybody, We're facing some trouble with our Windows Server 2008 R2 installation. The passwords expired and we're prompted to change the password. After changing it, we get following error message: Configuration Information could no be read from the domain controller, either because the machine is unavailable, or access has been denied. But we aren't even using a domain controller. So we tried running the server in Safe Mode where we get following message after changing the password: An attempt was made to logon, but the network logon service was not started. Are there any other things I could try? All help is more than appreciated!

  Read the article

• Using VMware Guest OS to enable Host OS to ssh to remote network

  - by Reuben L.

  Basically I have an issue because my host OS is 64-bit Linux Mint (Ubuntu derived) and it doesn't seem to be compatible with the Juniper Network Connect that is used by the network at my workplace. Thus, I am unable to ssh from terminal to the network. I can't make changes to the workplace network either so that leaves me with looking for solutions on my end. The main reason for me to access the network from home is to check on my running processes or to issue more commands to a few workstations. Putty is the desperate choice I usually make but it means I have to reboot to Windows and also have limited control. I've tried several other methods and they have all failed. Recently, I setup a VM with Windows 7 as the guest OS. Now half my problems are fixed as I don't have to physically reboot the system - I just have to engage Juniper Network Connect on the VM. However, I would still like to use my Linux terminal to ssh to the network. It sounds plausible that I could somehow manipulate ports to connect to the remote network from the host OS tunneled through the guest OS, but I really have no clue how to do so... Can anyone help?

  Read the article

• Need to open port in a router for two internal PC's

  - by Sergio

  I have two PC's behind a comon internet router and one service running in another network that needs to connect with both PC's through internet using a specific port. To avoid dynamic IP issues I have configured NO-IP accounts in both computers and opened the port in their respective Windows Firewalls. My problem is that when I open the port in the router it only allows me to assign it to one of the computers, but not to both of them. Is there any solution to this?

  Read the article

• Do two portforward rules translate to "and"?

  - by blsub6

  I just set up an Exchange server to replace my DeskNow mail server. I want to start testing my internet mail exchange of my Exchange server. I can only set the MX records on my DNS up to my one external IP address so I was thinking that I could set up a firewall rule on my internet-facing firewall that port forwarded the smtp packets to two different servers. My question is: If I do that, will that mean that the smtp packets will be forwarded to just the first internal IP on the list? Or does it mean that the packet will be cloned and sent to both IPs?

  Read the article

• Iptables rules, forward between two interfaces

  - by Marco

  i have a some difficulties in configuring my ubuntu server firewall ... my situation is this: eth0 - internet eth1 - lan1 eth2 - lan2 I want that clients from lan1 can't communicate with clients from lan2, except for some specific services. E.g. i want that clients in lan1 can ssh into client in lan2, but only that. Any other comunication is forbidden. So, i add this rules to iptables: #Block all traffic between lan, but permit traffic to internet iptables -I FORWARD -i eth1 -o ! eth0 -j DROP iptables -I FORWARD -i eth2 -o ! eth0 -j DROP # Accept ssh traffic from lan1 to client 192.168.20.2 in lan2 iptables -A FORWARD -i eth1 -o eth2 -p tcp --dport 22 -d 192.168.20.2 -j ACCEPT This didn't works. Doing iptables -L FORWARD -v i see: Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 33 144 DROP all -- eth1 !eth0 anywhere anywhere 0 0 DROP all -- eth2 !eth0 anywhere anywhere 23630 20M ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1 any anywhere anywhere 175 9957 ACCEPT all -- eth1 any anywhere anywhere 107 6420 ACCEPT all -- eth2 any anywhere anywhere 0 0 ACCEPT all -- pptp+ any anywhere anywhere 0 0 ACCEPT all -- tun+ any anywhere anywhere 0 0 ACCEPT tcp -- eth1 eth2 anywhere server2.lan tcp dpt:ssh All packets are dropped, and the count of packets for the last rule is 0 ... How i have to modify my configuration? Thank you. Regards Marco

  Read the article

• NAT Error Message - Usage limit exceeded

  - by Kato

  Trying to configure a port to use for Vuze. Using the NAT/server port test, I was getting a message saying the connection timed out, the port was probably closed. I went back and made sure to open the specific port on my router, firewall, etc, but now I'm getting "NAT Error - Usage limit exceeded (173.32.41.24:0). I'm on a mac pro running leopard, trial versions of intego netbarrier and virusbarrier. Network utilities and netbarrier both claim the port is open. I've tested a bunch of other ports, but all give the same message.

  Read the article

• IPv6 routing to another interface

  - by Robert

  I'm trying to get an IPv6 enabled router to forward data from one interface to the other and I'm having issues. When following this example (http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080ba6106.shtml) I am able to get full connectivity between all 3 routers in my simulator. However when I try to use only 1 router; I can't get connectivity to the other interfacs on the same router. My PC is directly attached to FA 0/1 and it can ping the router's interface. However it can not ping any other interface on the router(which unless I'm missing something it should be able to do). The router on the other hand can ping everything. I thought static routes might help; but the router already has routes for everything. I'm thinking the packet should come in; router looks up the destination in it's ipv6 routing table and then realizes it's for itself, and should respond. I thought maybe it couldn't respond directly; so I tried pinging a device like 2001:0000:0000:1000::2, but i don't get a response. I'm running on IOS 12.4. I'm missing something(hopefully simple), but I just can't see what it is. With only 1 router; how do I enable my PC to talk to the other subnets? Thank you in advance, Robert Topology: R1 FA 0/0: 2001:0000:0000:0000::1/52 FA 0/1: 2001:0000:0000:1000::1/52 FA 1/0: 2001:0000:0000:2000::1/52 Loopback 0: 2001:0000:0000:3000::1/52 PC: 2001:0000:0000:2000::2/52 PC plugs directly into FA 1/0 on the router. --- Configuration --- ipv6 cef ipv6 unicast routing interface Loopback0 no ip address ipv6 address 2001:0000:0000:3000::1/52 ipv6 enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000::1/52 ipv6 enable ! interface FastEthernet0/1 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:1000::1/52 ipv6 enable ! interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:2000::1/52 ipv6 enable --- end of config --- --- routing table --- IPV6Lab#show ipv6 route IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2001:0000:0000::/52 [0/0] via ::, FastEthernet0/0 L 2001:0000:0000::1/128 [0/0] via ::, FastEthernet0/0 C 2001:0000:0000:1000::/52 [0/0] via ::, FastEthernet0/1 L 2001:0000:0000:1000::1/128 [0/0] via ::, FastEthernet0/1 C 2001:0000:0000:2000::/52 [0/0] via ::, FastEthernet1/0 L 2001:0000:0000:2000::1/128 [0/0] via ::, FastEthernet1/0 C 2001:0000:0000:3000::/52 [0/0] via ::, Loopback0 L 2001:0000:0000:3000::1/128 [0/0] via ::, Loopback0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 --- end of routing table ---

  Read the article

• How to host an ssh server?

  - by balki

  Hi, I have a broadband internet connection. I have an wireless modem (Airtel India). I don't have a static ip address. I want to host a ssh/web/ftp server to be visible to the outside world just for testing and learning purpose so I can ask my friend to connect to my current ip address and test. My modem has an admin interface which allows to port forward and open ports. I set up ssh server as shown and checked if port 22 is open using this website , Port Scan And port 22 is open. I have an openssh server running and it works if i do, ssh [email protected] which is my local ip address but doesn't work if i do ssh [email protected] where 122.xx.xx.xx is my external ip address of my modem which i checked from whatismyipaddress.com. Since it looks like the port is open, I wonder if there is some setting I need to change in my server config to expose my server. How should I go about solving this?

  Read the article

• How can I redirect/forward all the UDP/TCP traffic on one interface to another interface in OpenWrt

  - by Sina Sou

  I am new to networking and I have a measurement device (D) that periodically sends all its readings over few UDP multicast sockets (with different multicast IP addresses and different port numbers). That device even listens to a TCP socket simultaneously to modify its configuration on port 7234. Since the device has just a Ethernet interface for communication and I want to make it work wireless, I decided to use a very small wireless open-wrt based router that attaches to the device (D) and redirect/forward all the network traffic(Both UDP/TCP) to the router wireless interface. In order to simplify the problem assume that the Device (D) establishes following sockets (at the same time) UM_SOCK1: UDP mcast socket on 239.1.2.3 port# 50620 UM_SOCK2: UDP mcast socket on 239.1.2.4 port# 50640 TC_SOCK3: TCP DHCP/STATIC ip address 192.168.1.200 port 7234 And (D) is connected to Open-Wrt router (R) via interface en01 (Ethernet) the router has it own wireless interface on (wlan0) I want all the traffic from interface pass through wlan01 and vice versa (bi-directional) en01 <---- wlan01 What would be the minimum iptables or ... commands that I need to make this possible? Even I am wondering if traffic directing can be made easier like if the direction is not going to be based on IP addresses(not desired if the device is connected via DHCP) I would rather redirection to be Interface(en0) based or on MAC address (The best solution since my device has unique MAC address)? Thanks

  Read the article

• Looking for a router-like web interface for my Debian gateway.

  - by marcusw

  Hey, I need a web interface program for my debian gateway which has the features of a router's one. Specifically, I must be able to easily Forward ports to various clients on the LAN or the router itself (it's also a server) Manage a DHCP server preferably including DHCP reservation for certain MACs Give me a list of the connected DHCP clients (optionally) Show which clients are the most active as far as bandwidth (something like iftop) Alternatively, it could be a graphical app which I could tunnel over ssh. No command line programs please...I'm used to doing this stuff with a point-and-click interface. Not adverse to command-line setup; just need to be able to reconfigure things graphically. Have a working LAMP setup. I've tried webmin, but it didn't satisfy the "easy" part...too many clicks and too many meny options.

  Read the article

• Access VirtualBox-ed server from behind the router

  - by migajek

  I'm having the following configuration: Windows 7 hosting VirtualBox and it's guest: Ubuntu The machine (physical) which runs VirtualBox is behind the router and has the address of 192.168.0.110 VirtualBox runs the Bridged network, and the IP of VirtualBox-ed Ubuntu (eth0) is 192.168.0.200 Host (Win7) is running HTTP service on port 80, while guest (Ubuntu) is running it's service on port 9000 I can access both services from inside the network by typing the ip_address:port and this works fine. Both ports are forwarded on the router to their's respective IPs: 80 -> 192.168.0.110:80 9000 -> 192.168.0.200:9000 Unfortunately, accessing the router's external IP doesn't work as expected. While external_ip:80 works correctly, external_ip:9000 - doesn't I believe the problem is VBox - related, since the same network is running also other physical machine with Ubuntu and http service on 8000 and this one is forwarded correctly.

  Read the article

• Is there a way to get att.net email to stay connected?

  - by Clay Shannon

  My att.net account at home (wireless connection) has been bad for the last several days: I have to hit F5 quite a few times to "unfreeze" it (I can read an email or two, then it freezes, etc.). At work (company LAN) it's even worse: I can connect to the site and see that I have email, but can't open any of the emails - and the screen constantly refreshes (every couple of seconds) with a "Connecting..." message. It apparently connects and disconnects over and over again, but never stays connected long enough to actually access the email. Is there a way either to fix this OR forward my att.net (from home) to my work email address (accessible via MS Outlook)? Or set it up from work using Outlook to pull in my att.net email? I have Outlook 2003 at work.

  Read the article

• Are less domains better than more domains in active directory?

  - by johnny

  A colleague of mine wants to add a domain to our forest. He said it would be good for security. I believe him but I have no idea why it is any better than with just one domain. I read this on Wikipedia but it has no source: "Microsoft recommends as few domains as possible in Active Directory and a reliance on OUs to produce structure and improve the implementation of policies and administration." I have no idea if it's right or not. I was hoping for comments. Thank you.

  Read the article

• Fastest browser to run over a forwarded X11 session

  - by warren

  So far I have tried Firefox (latest and greatest) and Chrome (also latest and greatest), and while Chrome runs faster than Firefox over X11 from my CentOS server to my Windows 7 workstation, it's still pretty sluggish. What other GUI browsers are available for Linux that would [likely] run faster than Chrome? I've not tried Opera 11, but have had many issues with it under Windows and Mac OS X directly, so am waiting for a new version before going that route.

  Read the article

• Remote desktop to multiple windows machines on a LAN with dynamic IP

  - by kevyn

  Is it possible to use remote desktop to connect to multiple computers inside a network that has a dynamic IP address? I use a netgear WPN824 router which has dyndns onboard - but I currently use No-IP to control a single computer that I use most frequently. Every so often I need to get onto a couple of other computers in the network, but don't know how to go about this without logging onto one computer, and then starting another RDC session from that machine. What I would like to be able to do is connect to my router, and be able to see a list of connected devices, and then choose which to remote desktop onto. - I appreciate this probably is not be possible, but any other suggestions are welcome!

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >