Search Results

Search found 3355 results on 135 pages for 'dual'.

Page 92/135 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

  • How do I recover from a grub renaming issue?

    - by Justin Ardini
    I am currently dual-booting Ubuntu 10.04 and Windows 7 with grub 1.98 as the bootloader. I recently decided to edit the grub menu to remove the old Ubuntu kernels, so I followed the instructions of this guide and added the line list='version_find_latest $list' to the 10_linux file, then ran sudo update-grub. Apparently I made a mistake, because upon restart I had these bootloader entries: Ubuntu, with Linux $list Ubuntu, with Linux $list (recovery mode) Ubuntu, with Linux version_find_latest Ubuntu, with Linux version_find_latest (recovery mode) When I try to load any of these, I get a grub error along the lines of, Error: not a normal file Now I can't start any version of Ubuntu to remove the line I added. What's the best course of action to be able to use Ubuntu again? Thanks.

    Read the article

  • RTL8168B/8111B Lan card is not detected in Redhat..Error is make ***/lib/modules/2.6.18-53.e15/build

    - by Deepak Narwal
    0 Hello friends... In My computer Lan card model is Realtek RTL8168B/8111B PCI-E GIGABIT ETHERNET NIC (NDIS 6.20) My system is dual boot windows 7 and redhat 5.1.Redhat is not picking up this model of Lan card automaticlly. I tried it by downloading from realtak site for this particular model and find some .tar packages for my kernal and when i tried to install them ... check old drivers & unload it build the module and install make */lib/modules/2.6.18-53.e15/build: no such file or directory stop make[1]: *[modules] error 2 make : [modules] error 2 i downloaded tar files from sites and unpack according to their instrution i tried to run autorun.sh script as mentioned in readme file but after doing this it is showing above error... Now what to do i am not getting

    Read the article

  • How to vertically split widescreen into two virtual workspaces on ubuntu/gnome?

    - by David
    My new laptop has a big 16:9 screen, and I'm finding it hard to fully utilize it during the 95% of the time that I'm not watching HD movies on it. I'd like to set it up as a kind of virtual dual screen by splitting the physical screen into two workspaces. I know I could arrange my windows manually, but I'd like to be able to maximize a window and have it only consume half the monitor, and have its pop up dialogs centered on its half-screen, that sort of thing. Is there some kind of plug in available to do this? Thanks in advance for any pointers.

    Read the article

  • Which hardware changes require operating system reinstallation?

    - by Mark
    I'm about to upgrade my computer but might keep some parts. Just wandering what I would have to keep to prevent me having to reinstall my OSs, at the moment I have a dual boot setup with ubuntu and windows 7. I'm pretty sure you can't just take your hard drive with the OS on it and put it into a different box and keep going (can you?) but I know you can change the graphics cards, secondary hard drives and ram with out a problem. So what is it that you can't change? The CPU? Motherboard? Thanks for any replies

    Read the article

  • Semantic is consuming all CPU, causing emacs to hang

    - by Cheeso
    I upgraded to emacs 23.2.1 on Windows 7, not long ago. Since then I've been unable to use Semantic. As soon as I start it, the cpu goes to MAX . (actually, Windows reports it at 50%, but this is a dual core machine, so emacs is effectively consuming 100% of a core). Emacs becomes non-responsive. Is there a particular combination of versions of semantic and emacs I that is unsafe to use together? how would I debug this spin/hang? I've seen other suggestions to change the semantic-idle-scheduler-idle-time, from its default 2 to something very large. I tried that, but got the same results.

    Read the article

  • DC on Hyper V Host

    - by Saif Khan
    I've read a few similar questions but wasn't clear. I have a small office (13) users and recently purchased a new single server (this is all I have to work with for now). Server specs Memory - 16GB Drives - 6 SCSI (2TB) PROCESSOR - DUAL QUAD I plan on making the Hyper-V host the DC and then 2 VMs, one for a file server and the other an application server. Question - since I am restricted to this single server, would it be a big issue making the Hyper-V host the domain controller? Your input greatly appreciated.

    Read the article

  • Will Software RAID And iSCSI Work For A SAN

    - by Justin
    I am looking for a SAN solution, but can't afford even entry level solutions. Basically, the SAN is for development and a proof of concept product. The performance doesn't have to be amazing, but needs to be functional. My buddy says we should just setup sotware RAID and software iSCSI in Linux. Essentially I have a spare server with dual Xeon processors, 4GB of memory, and (2) 500GB 7200RPM drives. It's a bit old but working. I am sure there is reason people don't do software RAID and iSCSI, but will performance be usable? Thinking of configuring the drives in RAID 0 (for performance).

    Read the article

  • WiFi: Connect to a network with hidden SSID in Windows 7

    - by Dor
    I have Windows 7 with the following station: D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.A2) (driver version 3.5.0.21). I'm trying to connect to a wireless network that has an hidden SSID with the command: Netsh wlan connect name="myNetworkProfile" The profile is configured to connect even if the network is not broadcasting its name (SSID). Despite that, the command fails promptly every time with the message: The network specified by profile "myNetworkProfile" is not available to connect. Nonetheless, when trying to connect manually using the dialog box (see image below), it successfully connects to the network after about 10 or 15 seconds. Also, Please - no need to elaborate about how useless the hidden SSID feature is.

    Read the article

  • Trixbox CentOS Default GW Problem (Multi-homed server)

    - by slashp
    I'm having an issue with a CentOS trixbox server which is dual-homed (one private facing NIC [eth1], one internet-facing NIC [eth0]). I can't seem to get the default gateway to set properly to our ISP's GW via eth0. I've modified the /etc/sysconfig/network to contain both a GATEWAY & GATEWAYDEV line and removed the GATEWAY line from /etc/sysconfig/network-scripts/ifcfg-eth1 (as well as /etc/sysconfig/network-scripts/ifcfg-eth0). No default GW shows up in the routing table unless it's specified in the ifcfg-eth1 file (which both the wrong interface and wrong gateway IP), otherwise, the routing table simply does not contain a default gateway..any ideas would be greatly appreciated! Thanks! EDIT Just realized when attempting to add the default gateway manually using the route add command, I receive an error stating: SIOCADDRT: Network is unreachable I know this error can occur when your default gateway and interface IP address are not on the same subnet..in this case, my public IP address of eth0 is a /29.

    Read the article

  • How to install OSX into VirtualBox on a Macbook Air using Apple's Reinstall USB

    - by eug
    I'm currently dual-booting OSX and Ubuntu on my Macbook Air, but it'd be nice to run OSX within Ubuntu via VirtualBox. This seems possible using VirtualBox and is legal - there's even a post on an Oracle blog describing this: http://blogs.oracle.com/karim/entry/installing_mac_os_x_in. Actually, I've read elsewhere that it's only legal with OSX Server, but can't find a reason why it'd be illegal with normal OSX - please let me know if you think otherwise. The problem I have is that a MacBook Air doesn't come with a bootable DVD, but with a "Reinstall Drive" which is a USB stick that comes up as a CDROM drive. It doesn't seem to be ISO9660-formatted though but has an Apple partition table, with OSX installed on an HFS partition. refit says that it has a "boot.efi" as well. I don't know Apple booting/partitioning very well and would really appreciate some advice on how to convert this USB into an ISO or boot it in VirtualBox some other way.

    Read the article

  • D-Link DWA-125 constantly disconnecting in winXP, but works fine on ubuntu..

    - by sil3nt
    Hey there, I'm dual booting winXp and ubuntu 10.10. I'm using a DWA-125 usb adapter to connect to my home wifi connection and I'm having this odd issue. First off, in ubuntu the adapter works fine and I have no trouble at all, but when I boot back in XP I get a dlink connetion wizard and the connection times out after every 2 minutes. It's odd because I can actually load up web pages and use the internet for 2 minutes, and then it would disconnect and the whole thing would repeat. I did a system restore on xp and this stopped the whole connect-disconnect thing but once I booted into ubuntu and came back to xp it started all over again!(?). Any ideas as to how I would go about fixing this?

    Read the article

  • Computer not displaying anything

    - by Justen
    The computer in question worked last week. It's brand new, never been connected to the internet, up-to-date parts, etc. Last week, I installed some 3D software on it, then shut it down and waited for the license files that arrived this week. I've done this to 4 other PCs with the same hardware and software. I've tried: Hooking it up to 3 different monitors using different video cables 2 other graphics cards and a handful of other things like switching which port it's plugged into before and after a restart. I have the driver disc, and a windows reinstallation disc, but they won't do me any good because no display at all for any interval of time. All the fans are moving: psu, gfx, cpu etc, so I don't believe it's a power issue. Here are the specs I know of: 4GB RAM 8800 GTX 700w PSU Intel dual core (not sure of model) Anyways, I'm open to ideas.

    Read the article

  • Grub loading. The symbol ' ' not found. Aborted. Press any key...

    - by John
    Hi there, I have a dual boot system on dell xps 9000 with windows 7 and ubuntu. But after I performed system backup on it as requested by windows 7 I am no longer able to boot into the computer, instead at the beginning after bios I get the following message: Grub loading. The symbol ' ' not found. Aborted. Press any key... I tried to change bios booting config to starting with harddrive and it still returned the same message. Using windows boot disk only asks me to do another system backup or threatens to delete my harddrive completely. The only solution I have so far is to reinstall ubuntu, but that leaves 2 additional copies of ubuntu on my computer. Is there a simpler way to fix the situation so I can actually boot into windows? Thanks so much.

    Read the article

  • My D-Link's Ethernet bridge downlink just got 10-30x slower?

    - by Jay Levitt
    TL;DR: I unplugged my network to move my desk, and now downloading via my DIR-655's Ethernet LAN bridge is 10-30x slower than the Ethernet switch it's plugged into. Background My network is SMC cable modem <-> Cisco firewall <-> Netgear switch <-> D-Link WiFi† | | | | SMC8014 ASA-5505 GS608v2 gigE DIR-655 rev A3 gigE †The DIR-655 is used as an access point, not a router (although what D-Link calls an access point, I'd call a bridge). The "WAN" port is unused; the Netgear connects to the built-in 4-port Ethernet LAN switch, inside the built- in router/firewall. Endpoints: MacBook Pro 17" mid-2010 iPhone 4S Fedora 12 Linux server running reasonably fast dual-Athlon X2, VelociRaptors, etc. All cables are <10 feet, mostly CAT-5e, some CAT-6, all premade. All WiFi endpoints are within three feet of the D-Link. Yesterday I unplugged and rearranged stuff, and now connecting via the D-Link - even through the wired switch, right next to the incoming network cable - is 30x slower than connecting directly to the Netgear switch, on both my MacBook and iPhone. How I'm measuring "slower" I'm mostly using http://speedtest.net, which of course only really measures broadband speeds. I've also installed http://www.speedtest.net/mini.php on my local server, but can't test the iPhone with that. Results Speedtest.net, closest server over Comcast business-class: CONFIG | PING (ms) | DOWN (Mbps) | UP (Mbps) Mac <-> Ethernet <-> Netgear | 9 | 31.6 | 6.8 Mac <-> Ethernet <-> D-Link | 8 | 4.1 | 6.0 Mac <-> WiFi <-> D-Link | 9 | 1.4 | 2.9 iPhone <-> WiFi <-> D-Link | 67 | 0.4 | 1.6 Speedtest Mini on Linux PC: CONFIG | DOWN (Mbps) | UP (Mbps) Mac <-> Ethernet <-> NetGear | 97.2 | 76.9 Mac <-> Ethernet <-> D-Link | 8.2 | 24.2 Mac <-> WiFi <-> D-Link | 1.0 | 8.6 Slow typing in SSH: Mac <-> Ethernet <-> Netgear <-> Linux PC: smooth Mac <-> Ethernet <-> D-Link <-> Linux PC: choppy Note that D-Link upload speeds are normal on broadband, slower locally (but I'd believe that's a D-Link limitation), and always faster than the downloads! Since ssh is choppy just with slow typing, I don't believe it's a throttling-type problem either; that's not a lot of bandwidth. What I've tried Swapping all "good" and "bad" cables Re-plugging "bad" cable from D-Link to Netgear and watching it be the "good" cable pulling cables away from power lines Verify that the Mac auto-detects the D-Link as gigE Try to verify the link speed of the D-Link <- Netgear connection, but the firmware doesn't report that Verify that the D-Link sees no TX/RX errors or collisions Use different Ethernet ports on both Netgear and D-Link Reset the D-Link to factory settings Upgrade the D-Link firmware from 1.21 to 1.35NA, 2010/11/12, the latest Reboot everything at least once On the Mac, disable Wi-Fi during the Ethernet tests, and unplug Ethernet during the Wi-Fi tests Using iStumbler, verify that the D-Link isn't picking overloaded Wi-Fi channels (usually just 1-5 neighbors on my and adjacent channels, average for my apt building) Verify that the only client connected to the Wi-Fi was the iPhone Verify that nothing was being chatty on my network according to the WISH log Enable and disable all sorts of D-Link settings, including forcing WAN auto-detect to gigE So. I don't mind buying a new access point—I wouldn't mind having a dual-link network—but as a guy who's been networking since gated v4 was a drastic rewrite, and who often used physical sniffers in the days before Wireshark, I'm baffled. I hate being baffled. What could I possibly have changed that would result in this? How can I measure it? All I can think of is a static zap—thick carpet, socks, HVAC—but I didn't feel one, and does that really happen anymore? Can I test if it's Ethernet vs. TCP layer slowness? I'm not familiar with modern network utilities; it's hard to Google without hitting "Q: Why is my network slow? A: Is your microwave on?" If I don't get an answer here, will someone big and powerful help me migrate it to serverfault without getting screamed back here? In the words of Inigo Montoya, "I must know." Don't get all Dread Pirate Roberts on me.

    Read the article

  • Eclipse: would more CPU cores with HyperThreading help increase speed?

    - by Dylan
    I'm programming a very large project in Eclipse. Right now I use a dual core machine with 2GB RAM, but Eclipse is sometimes busy for minutes (refreshing/indexing/building), so I'm upgrading to a new machine (with 16GB RAM and an SSD). Now I must choose between an Intel 2500K or an Intel 2600K that has HyperThreading. The price difference is about $100. Would that be worth it, for Eclipse, or is more memory/faster drive much more important for Eclipse ? Can Eclipse make use of the HyperThreading at all?

    Read the article

  • Laptop screen is cracked, external monitor only mirroring the broken laptop screen

    - by user92415
    I did something stupid. When my Dell Vostro 1000 laptop screen cracked and went all crazy and I couldn't see anything, I attached it to an external monitor and pressed Fn + F5 and it worked. But then I did something in the control panel that made the external screen look similar to the laptop screen. That made the external screen completely unusable too. In the control panel it was the last tab – something with "dual screens" I think. Is there anyway to reverse what did, turn off the laptop screen permanently and turn the external monitor into the primary? Remember that I can't see anything on the laptop screen. It is a complete goner – and because of what I did I can't see anything on the external monitor.

    Read the article

  • Caching DNS server (bind9.2) CPU usage is so so so high.

    - by Gk
    Hi, I have a caching-only dns server which get ~3k queries per second. Here is specs: Xeon dual-core 2,8GHz 4GB of RAM Centos 5x (kernel 2.6.18-164.15.1.el5PAE) bind 9.4.2 rndc status: recursive clients: 666/4900/5000 About 300 new queries (not in cache) per second. Bind always uses 100% on one core on single-thread config. After I recompiled it to multi-thread, it uses nearly 200% on two core :( No iowait, only sys and user. I searched around but didn't see any info about how bind use CPU. Why does it become bottleneck? One more thing, here is RAM usage: cat /proc/meminfo MemTotal: 4147876 kB MemFree: 1863972 kB Buffers: 143632 kB Cached: 372792 kB SwapCached: 0 kB Active: 1916804 kB Inactive: 276056 kB I've set max-cache-size to 0 to make sure bind can use as much RAM as it want, but it always stop at ~2GB. Since every second we got not cached queries so theoretically RAM must be exhausted but it wasn't. Do you have any idea? TIA, -Gk

    Read the article

  • Isolate user from the rest of the system..?

    - by Shiki
    There is a non-techsavvy user, who doesn't want to learn, and can only use Windows XP or 7. The problem is, that the computer is shared which she would like to use, and the computer stores sensitive, important data. Since she clicks on everything, it's quite a russian roulette. How could I isolate her account from the rest of the system? Like having a profile on the computer (it runs Windows 7 now) which would have the files and other stuff sandboxed? I was thinking of having a dual boot system, but that could compromise the files too, or the boot sector (talking about Windows). Linux is not a way, hence ... see the first line. Is there such a software that can set up a sandboxed environment?

    Read the article

  • how insecure is my short password really?

    - by rika-uehara
    Using systems like TrueCrypt, when I have to define a new password I am often informed that using a short password is insecure and "very easy" to break by brute-force. I always use passwords of 8 characters in length, which are not based on dictionary words, which consists of characters from the set A-Z, a-z, 0-9 I.e. I use password like sDvE98f1 How easy is it to crack such a password by brute-force? I.e. how fast. I know it heavily depends on the hardware but maybe someone could give me an estimate how long it would take to do this on a dual core with 2GHZ or whatever to have a frame of reference for the hardware. To briute-force attack such a password one needs not only to cycle through all combinations but also try to de-crypt with each guessed password which also needs some time. Also, is there some software to brute-force hack truecrypt because I want to try to brute-force crack my own passsword to see how long it takes if it is really that "very easy".

    Read the article

  • Scanned JPEGs are large and slow to load - can they be optimized losslessly?

    - by Alistair Knock
    I have hundreds of JPEG photographs which were scanned about 5 years ago from negative using a Konica Minolta DiMAGE Scan Dual IV. The dimensions are ~4500x3000, and the filesize is around 12Mb, compared to shots from a DSLR with dimensions of 3000x2300 and filesize of 2-4Mb (actually, these are the output from a RAW convertor). The filesize is obviously quite a big difference, but the issue that's bothering me is that the (perceived) loading time is at least 10 times slower. Is this size/speed discrepancy likely to be because the scanner software saved the JPEGs inefficiently / using an old compression format, or is it simply that the scanned negatives contain much more "detail" (in the form of grain/noise) than the digital images? If the former, is there a way to losslessly optimize them? I've tried re-exporting the scanned files to full size JPEG from my RAW software but the filesize is pretty much the same. Both files will have been saved at 100 quality.

    Read the article

  • Why does Windows 7 need hardware virtualization to run XP mode?

    - by Ken Pespisa
    I have a MacBook Pro and I've run VMware Fusion's unity mode and Parallels' cohesion mode along side the Mac OS X, and both work pretty seamlessly. I figured XP Mode in Windows 7 would be something similar, but I then learned my machine requires hardware virtualization support, which it does not have. My machine is an HP dc7800. That's a dual core 2.2GHz machine with 4GBs of RAM. Certainly it has the horsepower to run a virtual environment alongside the primary OS. I'm wondering: 1) Why Microsoft decided to make hardware virtualization a requirement and 2) What am I missing? Is the experience similar to Parallel's cohesion mode / Fusion's unity mode? Thanks!

    Read the article

  • How to use a custom Windows 7 system drive letter?

    - by Ivan
    The subject PC has many hard drive partitions dedicated for different purposes, C: being a Windows XP system drive and F: (which is actually the next primary partition placed right after C: physically) being intended to host a newly installed Windows 7 instance (meant for "dual boot" configuration). Needless to say the intention was all the partitions to have exactly the same letters under both OSes, needless to say Windows 7 has detected all of them in a completely different order which would not be a problem (as the non-system drives letters can be changed easily after installation) if it wouldn't have named it's system drive C: (meant to be F:), which I have no Idea how to change. Is there a way to set the letter you want? I don't mind reinstalling Windows 7 from scratch if it is to be set at installation time or even configured in some text files on the installation DVD. I have tried this way, but it renders the Windows 7 system desktop unbootable (gets stuck on "Preparing your desktop..." after "Welcome").

    Read the article

  • Changing the partition icon for Boot Camp

    - by zneak
    Hey guys, I've installed Windows 7 for a dual-boot setup on my new Core i7 MacBook Pro. Now, just for the looks, I'd like to change the volume icon. The partition is in NTFS format. I remember that in the past (with Leopard), you just had to add a .VolumeIcon.icns file at the root of a volume to set its icon. It seems this trick wore off with Snow Leopard. It apparently still works with CDs and DVDs, but hard drives keep that old, boring drive icon, no matter how lovely the .VolumeIcon.icns file I've put at the root. How can I change that?

    Read the article

  • Make GRUB automatically boot Ubuntu

    - by Matt Robertson
    I am running a dual-boot with Ubuntu (10.10) and Windows 7. Recently I edited my /boot/grub/grub.cfg file to only show one version of Ubuntu (as opposed to several kernel versions) and Windows, simply by commenting out all other menu entries. My question is if I can edit GRUB to just boot a specific entry automatically. I tried removing all other menu entries, but GRUB still showed the menu with only one entry. I've also considered just setting the timeout to either 0 or 1 second, as this would basically achieve the same thing. What is the best way to do this?

    Read the article

  • upgrading my computer system for office use

    - by denise ellul
    Presently I have the under-mentioned computer system. What should be changed and upgraded with the following products that I own presently? I am interested in performance issues related to cache memory, bus speed, RAM, CAS latency as well as other considerations. Thanks for your help. Processor (CPU): Intel Celeron Dual Core E3300 2.5 GHz Motherboard: Asus P5QPL-AM G41 Main Memory (RAM): 2 GB Team Elite DDR2 PC8000 Case: Coolermaster RC330 Power Supply Unit: 500W EZ-Cool Standard Storage Device (Hard Drive): 500GB Samsung Video Card: Intel GMA X4500 (On-board) Optical Drive: LG GH22NS50 Sound Card: AC 97 (On – board) Card Reader: Akasa Black TFT Monitor: 19” View Sonic Speakers: Logitech S120 2.0

    Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >